S2 Badge Kit (#28236)
|
|
- Valerie Fox
- 6 years ago
- Views:
Transcription
1 Web Site: Forums: forums.parallax.com Sales: Technical: Office: (916) Fax: (916) Sales: (888) Tech Support: (888) S2 Badge Kit (#28236) The Parallax S2 Badge Kit is a decorative printed circuit that features a smart LED and is easily assembled by novices and advanced users alike. Features Compact, easy-to-assemble module resembling an S2 robot Can be worn on a lanyard or placed on a level surface Seven-color LED, preprogrammed for various color effects Key Specifications Power requirements: CR2032 Lithium Battery Dimensions: 1.5 (38.1mm) dia. What Comes with the Kit Part Parallax No. Description Illustration (not to scale) Quan. PCB Printed circuit board 1 LED Multi-color smart LED 1 SW Tactile Switch 1 BH Battery Holder 1 BAT CR2032 Lithium Battery 1 WH!, WH Wheels 2 BENDER Lead Bender/Battery Remover 1 LANYARD Lanyard 1 Copyright Parallax Inc. S2 Badge Kit (#28236) Rev. A 4/9/2012 Page 1 of 5
2 What You Need to Provide for Assembly Fine-tipped soldering iron and small diameter (1/32 ) rosin-core solder (lead-free or leaded) Wire clippers Eye protection Vise or third hand Assembly Instructions Assemble the Circuit Board 1. Insert the tactile switch into the bottom of the printed circuit board. Be sure to press it in all the way so that it rests flat on the circuit board: 2. Solder the switch in place from this side, being careful not to melt the plastic switch body. Do two diagonally-opposite pins first, then recheck to make sure the switch is still pressed flat against the circuit board. Then solder the remaining two pins. Finally, clip the leads protruding through the top flush with the top surface of the circuit board. 3. Take the LED and insert it into the lead bender fixture as shown in the photo, making sure that the right-angle formed lead is in the rear and the diagonally-formed lead is in front: 4. Press the LED all the way into the fixture: Copyright Parallax Inc. S2 Badge Kit (#28236) Rev. A 4/9/2012 Page 2 of 5
3 5. Bend the leads of the LED over the wider tine of the fixture, once, and then down to form a complete 180 bend: 6. Check to make sure the LED s leads are oriented properly. With the LED pointed upwards and the leads bent behind it, the right-angle formed lead will be on the left; the diagonally-formed lead, on the right: 7. Insert the LED into the circuit board through the large hole, so that its rim rests against the edge of the hole: 8. Solder the LED s leads to the circuit board from this side, and clip the leads flush with the top side: Copyright Parallax Inc. S2 Badge Kit (#28236) Rev. A 4/9/2012 Page 3 of 5
4 9. Insert the battery holder into the board, being sure to press it in all the way so it rests flat: 10. Flip the board over and solder the tabs protruding through the holes to the circuit board: 11. Snap the wheels onto their axles, making sure that the spoke pattern points outward: Copyright Parallax Inc. S2 Badge Kit (#28236) Rev. A 4/9/2012 Page 4 of 5
5 12. Slide the battery into its holder, positive (+) side up. It is very important not to insert the battery upside down. Doing so will damage the LED: 13. Once the battery has been inserted, the LED will go into a power-up mode where it cycles through all of its colors and then flashes them for a while. Once this cycle is complete, the tactile switch may be used to select from among seven constant colors or a mode that cycles through them. The switch can be activated either by pressing it from behind the circuit board or by pressing on the rear of the badge while it s sitting on a level surface. Any mode in which the LED is off will draw minimal current from the battery, so the battery can be left in place without fear of it draining prematurely. 14. To remove the battery, use the skinny tine of the lead-bending tool to push it out: 15. Once the badge is assembled and the battery installed, it may be snapped onto the included lanyard to be worn around the neck if desired. Copyright Parallax Inc. S2 Badge Kit (#28236) Rev. A 4/9/2012 Page 5 of 5
Arlo Power Distribution Board Kit Rev B (#28996)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationArlo Power Distribution Board Kit Rev B (#28996)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationArlo Power Distribution Board Kit (#28996)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationWeb Site: Forums: forums.parallax.com Sales: Technical:
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationMotor, Bracket and Wheel Kit (# )
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationMotor, Bracket and Wheel Kit (# )
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationThese instructions show how to build the Remote Controlled Fart machine Sound Kit.
Remote Controlled Fart Machine Assembly Instructions These instructions show how to build the Remote Controlled Fart machine Sound Kit. Tools Required Drill with 7/64, 3/16, and ¼ drill bits. Holt melt
More informationWild Thumper Robot Kit (#28192) Information and Assembly Guide
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationDuraShield Installation Manual
MOTORIZED FACE OF WALL GENERAL MOUNTING DIAGRAM Chase Doors Inc. 800-543-4455 Page 1 8/12 1. Wall preparation refer to following drawing Note and understand the clear opening width and height dimensions
More informationBuild Instructions and User Guide
Build Instructions and User Guide Getting Started To build the Rock Drill 4069 you will need: Solder Wire Cutters Soldering Iron Small pliers The kit is suitable for beginners or more experienced builders
More informationInstructions: General American 6,000 Gallon, 3-Compartment Tank Car Kit 11/2013
Instructions: General American 6,000 Gallon, 3-Compartment Tank Car Kit 11/2013 Thank you for purchasing the Tangent Scale Models General American 6,000 Gallon, 3- Compartment Tank Car Kit! A few quick
More informationLAB 3 SeaMATE PufferFish Practice Board
LAB 3 SeaMATE PufferFish Practice Board Components: Practice Board Kit, (2 resistors, 2 LEDs, 1 DPDT switch, 1 PCB, 1 9-volt battery connector, 2 motor wires color varies) Tools & equipment needed: Safety
More informationAthearn Pacific Digital Sound Decoder Installation Notes
New Dimensions in Digital Sound Technology TM APPLICATION NOTE Overview This application note describes how to install a DSD-100LC Digital Sound Decoder into the Athearn Pacific Locomotive. All of the
More informationBase Kit Chain Drivetrain Build Guide
222fg Base Kit Chain Drivetrain Build Guide August 11, 2017 Chain Drivetrain Build Guide Copyright 2017 REV Robotics, LLC 1 1.1 Description This document outlines the steps required to four wheel, chain
More informationApplication Note. KATO SD40-2 Mid Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a Tsunami TSU-KT1000 Digital Sound Decoder into the HO Kato SD40-2 (Mid-production). Skill Level 2: The entire installation can
More informationUseless Box Kit. Rev 2. March 24, 2014 Kansas State University Electronics Design Club Nathan Reichenberger
Required Materials: Useless Box Kit Rev 2 March 24, 2014 Kansas State University Electronics Design Club Nathan Reichenberger Quantity Description 1 Double Pole Double Throw Switch 1 Micro Switch 1 Battery
More informationApplication Note. Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes
Application Note Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into an HO Atlas RS-3. Skill Level
More informationElectrometer NiCad Battery Replacement
Electrometer NiCad Battery Replacement Table of Contents NOTE: Although this manual is provided by Standard Imaging as a reference, battery replacement by anyone other than a trained Standard Imaging employee
More informationUNPACK AND IDENTIFY THE FOLLOWING PARTS.
SUT-500-S ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first
More informationFigure 1. A CheapBot Robot
A CheapBot controller needs a robot body to function. An ideal robot body for the beginner consists of two sheets of Syntra plastic, separated by four bolts. The bottom deck contains the robot controller
More informationQRPGuys Digital RF Probe
QRPGuys Digital RF Probe First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. This kit contains seventeen 1206 size
More informationUno Compatible Pogobed Kit
Uno Compatible Pogobed Kit Intermediate Level The pogobed kit is a hardware fixture that enables you to temporarily connect from your Arduino development board to any Arduino shield. Using the springloaded
More informationBLUE LIGHT FOR DYNACO STEREO 120 OR PAT-4 ROCKER SWITCHES
BLUE LIGHT FOR DYNACO STEREO 120 OR PAT-4 ROCKER SWITCHES 2012 AkitikA, LLC All rights reserved Revision 1p3 April 18, 2012 Page 1 of 15 Table of Contents Table of Contents... 2 Table of Figures... 2 Section
More informationDuraShield Installation Manual
SOMFY IN-TUBE MOTOR IN JAMB GENERAL MOUNTING DIAGRAM Page 1 1. Wall preparation refer to following drawing Note and understand the clear opening width and height dimensions of the purchased door before
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More information2003 CR-V - A/T Shift Cable Replacement-Print Preview
Page 1 of 7 2003 CR-V - A/T Shift Cable Replacement 1. Raise the front of the vehicle, or lift the vehicle up, and make sure it is securely supported. 2. Remove the driver's dashboard lower cover, and
More informationWeb Site: Forums: forums.parallax.com Sales: Technical:
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationNOTICE: Using old water pump seal installer J on the new water pump coolant seal will result in damage to water pump.
SERIES 60 SERVICE MANUAL Detroit Diesel previously released a water pump coolant seal which required the use of seal installer J 35988-19, part of tool set J 35988-D. This seal went into effect with engine
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationAtlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes
Atlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into an Atlas Silver
More information20964/B 20964/B 2014 TOYOTA TUNDRA TUNDRA. Billet Grille. Fig 1. Fig 2
Billet Grille TOOLS REQUIRED: PARTS LIST: Socket Set (6) U-Nuts Flat/Phillips Screw Drivers (8) #10 Screws Pliers (2) #8 Screws ¾ (2) 2 Flange Bracket (1) Top Plate Overlay Bracket - driver (1) Top Plate
More informationMGV (Marshall TM Guv'nor TM Replica) Instructions
This is a replica of the Marshall TM Guv'nor TM Distortion referred to as MGV in these documents. Use the project documents provided, starting with the General Build Instructions. Follow the layout diagrams
More information11. FRONT WHEEL/SUSPENSION/
11 FRONT WHEEL/SUSPENSION/ SERVICE INFORMATION------------------------------------------------ 11-2 TROUBLESHOOTING----------------------------------------------------- 11-3 HANDLEBAR ---------------------------------------------------------------
More informationAtlas HO MP-15 Tsunami Digital Sound Decoder Installation Notes
Atlas HO MP-15 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into an Atlas HO MP-15. Skill Level 2: The entire
More informationPN K K050012: Rebuild Kit for Delco Non-Delay Height Control Valve
APPLICATION: 1959 1989 Cadillac, Oldsmobile, Buick, GMC Truck, Ford, Fruehauf Trailer INTRODUCTION This kit provides the necessary parts and instructions to rebuild Delco/King of the Road non-delay valves.
More informationBLUE LIGHT FOR DYNACO STEREO 120, SCA-80, OR PAT-4 ROCKER SWITCHES
BLUE LIGHT FOR DYNACO STEREO 120, SCA-80, OR PAT-4 ROCKER SWITCHES 2014 AkitikA, LLC All rights reserved Revision 1p5 April 8, 2014 Page 1 of 16 Table of Contents Table of Contents... 2 Table of Figures...
More information12. FRONT WHEEL/FRONT BRAKE/
12 12 12-0 SERVICE INFORMATION... 12-1 FRONT BRAKE... 12-7 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-18 STEERING HANDLEBAR... 12-3 FRONT FORK... 12-21 FRONT WHEEL... 12-4 SERVICE INFORMATION GENERAL
More informationIR Gun Assembly Instructions
IR Gun Assembly Instructions Rev 1.01 SenselessDevices.com 1 Description The IR Gun is part of a shooting Arcade project. Together with the target kits, a variety of shooting galleries can be constructed.
More informationSet Up instructions DB30 Doodlebug Removal from crate
Set Up instructions DB30 Doodlebug Removal from crate 1. Remove carton top 2. Remove set up instuctions, owners manual and parts. E - REV - B Hardware and Parts Front fork assembly Hardware 10mm Front
More informationKimray reserves the right to modify or improve the designs or specifications of such products at any time without prior notice Kimray Inc.
TREATER VALVE All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be construed
More informationRead and understand all instructions and warnings prior to installation of product and operation of vehicle.
#F9378 Installation Instructions 1998-2000 Ford Ranger 3" Body Lift Kit Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products
More informationBrake Shoe: Service and Repair Removal Procedure
2000 Buick Century V6-3.1L VIN J Copyright 2013, ALLDATA 10.52 Page 1 Brake Shoe: Service and Repair Removal Procedure ^ Tools Required - J38400 Brake Shoe Spanner and Spring Remover Caution: Keep fingers
More informationWifiTrax WMR-10 in Atlas RS-3
WifiTrax WMR-10 in Atlas RS-3 How to Install the WifiTrax WMR -10 Board Replacement Wi-Fi Controller in Atlas RS-3 Locomotive Practical notes by Steve Shrimpton Back to Web Site In my opinion the Alco
More information*NOTE* The following suspension system will not work with heavy duty axle housings as pictured below.
1964 ½ - 1970 Ford Mustang Triangulated 4-Link Suspension Installation Instructions Tech Line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work!
More information4.2 WATER PUMP (GEAR CASE MOUNTED AND LATER) (GCM)
SERIES 60 SERVICE MANUAL 4.2 WATER PUMP (GEAR CASE MOUNTED - 1991 AND LATER) (GCM) The centrifugal-type water pump circulates the engine coolant through the cooling system. The pump is mounted on the rear
More informationBachmann Digital Sound Decoder Installation Notes
New Dimensions in Digital Sound Technology TM APPLICATION NOTE Bachmann 2-6-6-2 Digital Sound Decoder Installation Notes Overview This application note describes the installation of a DSD-090LC Digital
More information22K (red red orange gold) 1pcs. 33K (orange orange orange gold) 5pc. 2.7 M (green violet red gold) 2pc.
TURNING FROG Long pliers, soldering, soldering iron stand with sponge, 2 AA batteries, one 9V battery, Tin, diagonal cutting pliers Turning Frog is a robot that uses a microphone as a detector. When microphone
More informationDetroit Speed, Inc. Mini Tubs Camaro/Firebird P/N:
Detroit Speed, Inc. Mini Tubs 1967-1969 Camaro/Firebird P/N: 040401 The Detroit Speed Mini-Tubs are inner wheel housings designed to accommodate a wider wheel and tire package. They are engineered for
More informationSR500 PAPR How to Copyright 2015 by The S.E.A. Group 1
SR500 PAPR How to Copyright 2015 by The S.E.A. Group 1 BEFORE YOU START: Make sure the respirator and all its parts are clean and intact Make sure you are familiar with the equipment and know how to use
More informationCTB-16K Hobbyist Line Kit 40 Amp 16 Channel Light Controller Assembly Manual *** Preliminary ***
CTB-16K Hobbyist Line Kit 40 Amp 16 Channel Light Controller Assembly Manual *** Preliminary *** Version 1.0 January 12, 2006 Copyright Light O Rama, Inc. 2006 Table of Contents 1 Introduction... 3 2 Required
More informationInstallation Instructions for C & R Heat Exchanger Removal of Factory Unit
Installation Instructions for C & R Heat Exchanger Removal of Factory Unit Remove the 8 clips that retain the upper radiator shroud. Remove the shroud. Remove the coolant tank cap from the heat exchanger
More informationHow to Replace the Main Axle Gear on the Bachmann Spectrum GScale using the NWSL # upgrade gear.
How to Replace the Main Axle Gear on the Bachmann Spectrum GScale 4-4-0 and 2-6-0 Mogul (2001era), using the NWSL #2223-6 upgrade gear. By Paul M. Newitt (all text and photos Copyright Paul M. Newitt,
More informationOreck Magnesium Series Service Manual. The Oreck Manufacturing Company
Oreck Magnesium Series Service Manual The Oreck Manufacturing Company 08/2012 10/2011 The Oreck Manufacturing Company Contents Covering all Magnesium Upright Models Including: LW100, LW125, LW1000, AND
More informationGTFLOW EXTENSION MANIFOLD ASSEMBLY INSTRUCTIONS
Page 1 of 5 Step 1: ASSEMBLE THE MAIN MANIFOLD AND MANIFOLD EXTENSION KIT First and very important step is to properly connect the main manifold and the manifold extension kit together by using the two
More informationRS04 RS16 RS19 RS18 PHOTOETCHED: CAST: DECALS: SCREWS: OTHER: - RS02 RS03 RS04 RS05 RS08 RS09 RS16 RS18 RS19 M23. 8x T03
PART 2 chapter 3 building steps 2 A1 Engine/gearbox casing Cyanacrylate () sand paper RS19 RS04 RS16 RS02 RS09 RS08 RS05 RS03 Stick together the crankshaft casing as gap-free as possible from the designated
More information12. FRONT WHEEL/FRONT BRAKE/
12 4.5kgm 0.9kg-m 4.5kg-m 12-0 SERVICE INFORMATION... 12-1 HYDRAULIC BRAKE... 12-10 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-16 FRONT WHEEL... 12-3 STEERING HANDLEBAR... 12-19 FRONT BRAKE...
More informationQrpkits.com 10 Watt SMT Dummy Load Assembly and Operating Manual
Qrpkits.com 10 Watt SMT Dummy Load Assembly and Operating Manual Introduction The Hendricks 10 Watt (DC 150MHz) 50 Ohm Dummy Load kit is a compact, SMT (Surface Mount Technology) design, that in addition
More informationPrusa i3 Printer Assembly Guide
Prusa i3 Printer Assembly Guide Special thanks to Carlos Sanchez and Miguel Sanchez for the graphics. All graphics captured from their great animation: http://www.carlos-sanchez.com/ Prusa3/ For copyright
More informationDetroit Speed, Inc. Mini Tubs Camaro/Firebird P/N:
Detroit Speed, Inc. Mini Tubs 1967-1969 Camaro/Firebird P/N: 040401 The Detroit Speed Mini-Tubs are inner wheel housings designed to accommodate a wider wheel and tire package. They are engineered for
More information(H) TOUR VANTAGE STROLLER ASSEMBLY INSTRUCTIONS ADULT ASSEMBLY REQUIRED. Styles and colors may vary
TOUR VANTAGE STROLLER ASSEMBLY INSTRUCTIONS ADULT ASSEMBLY REQUIRED Styles and colors may vary IMPORTANT: Read all instructions before assembly and use of the stroller Keep the instructions for future
More informationENG CRANKCASE AND REED VALVE. REED VALVE INSPECTION 1. Measure: 8 Valve stopper height 1 Out of specification Adjust stopper/replace valve stopper.
CRANKCASE AND REED VALVE ENG REED VALVE INSPECTION. Measure: 8 Valve stopper height Out of specification Adjust stopper/replace valve stopper. Valve stopper height 6.0~6. mm(0.~0.5 in). Measure: 8 Reed
More information»Product» Safety Warning
J1457, J1458 Installation Instructions 1984-2001 Jeep Cherokee XJ 4.5 Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationFOR FUTURE REFERENCE SERIES 93HPS
Hypro Series 93HPS Hydraulically Driven Wetseal Multistage Pumps Repair Manual KEEP FOR FUTURE REFERENCE Form L-1578R Rev. A SERIES 93HPS Hydraulically Driven Stainless Steel Multistage Centrifugal Pumps
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 6525 REAR AXLE FLIP & HANGER KIT 5 OR 6 INCH LOWERING 14&UP CHEVROLET SILVERADO / GMC SIERRA 1500 Thank you for being selective enough to choose our high quality BELLTECH PRODUCT.
More information29048, 29049, 29050, 29051, 29052, 29053, 29054,
May 1, 2018 Lit. No. 29206, Rev. 13 29048, 29049, 29050, 29051, 29052, 29053, 29054, 29400 7 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM w/3 PLUG SYSTEM HARNESSES Installation Instructions Read this
More information»Product» Safety Warning
#F9383 Installation Instructions 2004-2005 F-150 5dr/5.4L 3" Body Lift without Factory Receiver Read and understand all instructions and warnings prior to installation of product and operation of vehicle.
More information(WW03f) BR PIPE WAGON 4 shoe brake
(WW03f) BR PIPE WAGON 4 shoe brake History. The pipe wagons were built to four basic diagrams sharing the same basic dimensions. The first 300 pipe wagons were built at Derby works to diagram 460, and
More information200-4R TRANSMISSION LOCK-UP HARNESS INSTALLATION INSTRUCTIONS
2501 Ludelle Street Fort Worth, Texas 76105 817-244-6212 Phone 817-244-4024 Fax 888-350-6588 Sales 800-423-9696 Tech E-mail: painless@painlessperformance.com Web: www.painlessperformance.com 60110 200-4R
More informationDuraShield Installation Manual
SIMU IN-TUBE MOTOR IN JAMB GENERAL MOUNTING DIAGRAM Page 1 1. Wall preparation refer to following drawing Note and understand the clear opening width and height dimensions of the purchased door before
More informationPRODUCT MANUAL Gecko Wireless One Zone LED Dimmer and Receiver
Product Description The Gecko Wireless One Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location
More informationEvo X Walbro 450 Pump System
Evo X Walbro 450 Pump System Installation Guide Please contact us at sales@wtftuned.com with any additional questions Tools required: 8 mm socket and wrench, needle-nose pliers, razor, drill w/ 5/64 bit,
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationBachmann D11 EM/S4 Finescale Conversion
Bachmann D11 EM/S4 Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than crawling
More informationSachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport
Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,
More informationZeiss ZAT Cube Assembly Procedure
1.1.1 The ZAT cube assembly has two filter retainer rings; one is located on the Exciter side and one is on the Emitter side as shown below. Note that the Exciter housing is marked with a red dot and the
More information29048, 29049, 29050, 29051, 29052, 29053, 29054,
April 15, 2014 Lit. No. 29206, Rev. 11 29048, 29049, 29050, 29051, 29052, 29053, 29054, 29400 5 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM w/3 PLUG SYSTEM HARNESSES Installation Instructions Read
More informationOVERHAUL. Using SST, disconnect the 2 brake tubes from the master cylinder. SST
3215 320J001 OVERHAUL 1. DRAIN BRAKE FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface. 2. REMOVE AIR CLEANER CAP SUBASSY 3. REMOVE (a) Disconnect the brake fluid
More informationBuild your own THUNDERBIRD 2
PACK 11 PAGE 67 Pod 4 ramp tracks and Jet Air Transporter 224 68 Left rear booster and Alan s Racing Car 227 69 Right rear booster and Alan s Racing Car 230 70 Left booster speaker 233 71 Right rear booster
More informationRe-Energy.ca - Solar Electricity - Build Your Own Solar Car
Backgrounder Build Your Own Solar Car Back to Page 1 Build It! These step-by-step instructions provide you with a plan for making a basic solar car. If you can think of ways to improve the design of your
More information»Product» Safety Warning
J1455, J1456 Installation Instructions 1984-2001 Jeep Cherokee XJ 4.5 Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS COOLANT EXPANSION TANK FORD FOCUS Document: 19-0151 Support: info@radiumauto.com WARNINGS: DO NOT WORK ON THE COOLANT SYSTEM WHEN THE ENGINE IS AT OPERATING TEMPERATURE. WAIT
More informationw w w. h d o n l i n e s h o p. d e FLHT FRONT END LOWERING KIT GENERAL -J02546 REV Kit Number Models Additional Parts Required
-J0546 REV. 007--0 GENERAL Kit Number 5468-06 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English only). Additional
More informationMaintenance Information
45530136 Edition 1 July 2008 Electric Screwdrivers EL 24V DC Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this tool.
More informationPart Numbers: TTU-BGP14 & TTU-BGB14
Date: 10.14.2015 TOYOTA TUNDRA 2014-17 Billet Grille Part Numbers: TTU-BGP14 & TTU-BGB14 Grille Hardware Bag Contents Item # Quantity. Description 1 6 U-Nuts 2 8 #10 Screws 3 2 #8 Screws 4 2 2 Flange Brackets
More information401B/1KDB CoolRite/FreezeRite Installation Manual I003
401B/1KDB CoolRite/FreezeRite Installation Manual 99-16105-I003 Copyright 2011 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in
More informationSHELBY GT500
2007-2009 SHELBY GT500 Removal of Factory Unit WARNING: 1. Radiator fluid must be handled properly. Please observe local ordinances with regards to handling and disposal. 2. Allow vehicle and components
More informationAC-20 Multi Point Actuator
29.6 (1.17) 51.1 (2.01) 29.6 (1.17) 51.1 (2.01) Cable B 52 27.3 (2.05) (.68) 27.3 (.68) 4X Ø 5.2 ± 0.1 (.210 ±.005) Cable A 29.6 (1.17) 17.3 (.68) 80.9 (3.19) 119 (4.7) (1.17) AC-20 Multi Point Actuator
More informationInstallation Instructions
1999-2010 GM 2500-3500 HD 18K Industry Standard SuperRail Custom Mounting Kit #2326 Industry Standard Super 5 th #1900 Gross Trailer Weight (Maximum) 16,000 lbs. Vertical Load Weight (Max. Pin Weight)
More informationDRIVE SHAFT LOCATION INDEX
DRIVE SHAFT LOCATION INDEX 2005 DRIVELINE/AXLE Drive Shaft - MX-5 Miata Fig. 1: Identifying Drive Shaft Location DRIVE SHAFT PRE-INSPECTION 1. Inspect the dust boot on the drive shaft for cracks, damage,
More informationTake off case cover.
33 14 520 Removing complete locking differential. (Type K) - final drive removed - Removing and installing final drive, refer to 33 10 010 Drain off fluid. Secure final drive to special tool 33 1 010 (retaining
More informationAET48 Owner s Manual. TOW AERATOR Owner s Manual AET48 Beginning Serial #: Replacement Parts
Tine Row Kit Complete tine row set for replacement of one complete row of tines. Includes mounting plates, spacer, and all hardware. TOW AERATOR Owner s Manual AET48 Beginning Serial #: 0206001 Tine Kit
More informationMopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion
Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion This kit is for either Mopar 8 ¾ or Mopar 9 ¾ (Dana). This kit is designed to work with axles with either GM 5 x 4.75 Bolt Pattern
More informationInstallation Instructions: Epson 1400 CFS
Installation Instructions: Epson 1400 CFS Epson 1400 with MIS CFS Installed *A perfect print with OEM cartridges is a must* Prerequisite - Before starting this installation, you MUST test your printer
More informationLEXMARK C780 CARTRIDGE REMANUFACTURING INSTRUCTIONS LEXMARK C780 TONER CARTRIDGE
LEXMARK C780 CARTRIDGE REMANUFACTURING INSTRUCTIONS LEXMARK C780 TONER CARTRIDGE REMANUFACTURING THE LEXMARK C780 BLACK & COLOR TONER CARTRIDGES First released in April 2008, the Lexmark C780 is based
More informationHOW TO CHECK YOUR G4 SPREAD PATTERN
HOW TO CHECK YOUR G4 SPREAD PATTERN - NEW LEADER DIVISION 1330 76 th AVE SW, CEDAR RAPIDS, IOWA 52404-7052 PH. (319) 363-8281 www.highwayequipment.com FAX (319) 632-3081 SPREAD PATTERN UNIT SERIAL NUMBER
More informationOptimax Pro Retrofit Instructions
Copyright 2011 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in examples herein are fictitious unless otherwise noted. No part
More information24 Volt Eco Flex LED Neon Part Numbers: LFN-2700K, LFN-5800K
24 Volt Eco Flex LED Neon Part Numbers: LFN-2700K, LFN-5800K 11235 West Bernardo Court, Suite 102 San Diego, CA 92127 888-880-1880 Fax: 707-281-0567 EnvironmentalLights.com Eco Flex LED Neon is an adaptable
More informationSMD Push-to-Fix (P2F) Reflowable fixing element for LED boards
LED A50 cd / klm SMD Push-to-Fix (P2F) Reflowable fixing element for LED boards 100 200 300 400 500 The smartest route to your LED application Waterproof luminaire with cover Batten luminaire Pendant luminaire
More informationSMITHS CAR CLOCK REPAIR KIT
SMITHS CAR CLOCK REPAIR KIT Version 9 1 Introduction These instructions explain how to repair a Smith s electric car clock mechanism using the Clocks4Classics repair kit. This kit uses a specially developed
More informationInstallation Guide. Enhanced Easy-Stop Trailer ABS 2S/2M Standard with PLC Installation Instructions TP Revised 1 Technical Bulletin
Revised 08-05 Installation Guide Enhanced Easy-Stop Trailer ABS 2S/2M Standard with PLC Installation Instructions Revised 1 Technical 08-05 Bulletin Hazard Alert Messages Read and observe all Warning and
More information