GTFLOW EXTENSION MANIFOLD ASSEMBLY INSTRUCTIONS
|
|
- Hilary Elliott
- 5 years ago
- Views:
Transcription
1 Page 1 of 5
2 Step 1: ASSEMBLE THE MAIN MANIFOLD AND MANIFOLD EXTENSION KIT First and very important step is to properly connect the main manifold and the manifold extension kit together by using the two Core Connectors provided in the kit. Do not assemble anything else before this step is completed. Apply plumber putty or Teflon tape on both sides of the Core Connector (16). Take the Manifold Core with Flow Meter (5B) and thread the core connector into it. Next, thread the extension Manifold Core with Flow Meter (5B) on the other side of the Core Connector (16). Make sure the Core Connector (16) is threaded all the way and both manifold cores are aligning well so the flow meters are aligned vertically side by side. If Manifold Cores do not align perfectly, unthread one Manifold Core and thread it on the other side. In the same manner move the Core Connector being threaded to the other side of the Manifold Core until required alignment is achieved. Take the Manifold Core with Port Valves (5A) and thread the core connector into it. Next, thread the extension Manifold Core with Port Valves (5A) on the other side of the Core Connector (16). Make sure the Core Connector (16) is threaded all the way and both manifold cores are aligning well so the flow meters are aligned vertically side by side. If Manifold Cores do not align perfectly, unthread one Manifold Core and thread it on the other side. In the same manner, if required, move the Core Connector being threaded to the other side of the Manifold Core in order to find the configuration allowing aligning them perfectly. Step 2: ASSEMBLE THE MANIFOLDS Screw the Air Vent and Bleeding Valve (3B) into the Manifold Core with Flow Meters (5B) tightly; making sure the Air Vent (3B) is pointing to the opposite direction of the Flow Meters (8). If the Air Vent and Bleeding Valve (3B) does not align vertically with the Manifold Core and Flow Meters (5B) after it is tightened, try installing it on the opposite side of the Manifold Core with Flow Meters (5B) to get the correct alignment. Repeat the same process as above to install the Air Vent and Bleeding Valve (3A) in the Manifold Core and Manifold Extension Core assembly with Port Valves (5A). Thread both PEX Male Threaded Adaptors (10) to both Metric Converters (11). Thread one assembly to the Return Ball Valve (Blue) (1) and the other to the Supply Ball Valve (Red) (9). We recommend using plumbers putty or Teflon tape on both PEX Male Threaded Adaptors (10) and Metric Converters (11) to avoid any leaking. Page 2 of 5
3 Thread the Supply Ball Valve (Red) (9) into the Manifold Core with Flow Meters (5B). Thread the Supply Ball Valve (9) into the Manifold Core with Flow Meters (5B) tightly, without over tightening the gasket; making sure the handle (9) is pointing to the Flow Meters (8) on the Manifold Core (5B). Thread the Return Ball Valve (Blue) (1) into the Manifold Core (5A) with Port Valves (2). Thread the Return Ball Valve (1) into the Manifold Core with Port Valves (5A) tightly, without over tightening the gasket; making sure the handle (1) is pointing to the Port Valves (2) on the Manifold Core with Port Valves (5A). In order to align the temperature gauge outward (7A and 7B) loosen the nut on the thermometer (7A and 7B), then tighten. Step 3: ASSEMBLING THE FIXTURES DO NOT ASSEMBLE ON THE WALL AT THIS POINT. WE SUGGEST YOU ASSEMBLE IT ON THE FLOOR BEFORE MOUNTING TO THE WALL TO AVOID DAMAGE. Place the two Wall Mount Brackets (4) parallel, with the less elevated side of the Wall Mount Bracket (4) on the upper position (5B Manifold Core with Flow Meters to be attached at the upper position) so the bottom of the bracket is further off the floor at this point (5A Manifold Core with Port Valves to be attached to this bottom part of bracket). Place the manifolds on the small rubber guides located on the Wall Mount Brackets (4). Make sure the Manifold Core with Port Valves (5A) is in the bottom position of the Wall Mount Bracket (4) and the Manifold Core with Flow Meters (5B) is in the upper position. Install one bracket between the first two Core Ports (6) and the other bracket between the last two Core Ports (6). NOTE: Both main manifold and extension manifold must be supported by their own brackets to ensure the performance of the product and to avoid stress on the core Connector. Step 4: SECURING MANIFOLDS TO THE WALL MOUNTING BRACKETS (4) Secure the Manifold Core with Flow Meters (5B) and Manifold Core with Port Valves (5A) to Wall Mounting Brackets (4) using the 8 Manifold Mounting Bracket Screws (15) provided in the kit. Drive the screw until the screw head is secured flat on the bracket. Step 5: MOUNTING ON WALL Mount the GTFLOW Manifold on the wall. Make sure the proper mounting screws and/or anchors are used for that type of wall (not included). IMPORTANT: THE MOUNTING METHOD YOU USE SHOULD BE ABLE TO SUPPORT A MINIMUM OF 30LBS (14KGS). Page 3 of 5
4 Step 6: PURGING THE SYSTEM Make sure the Return Ball Valve (Blue) (1) and the Supply Ball Valve (Red) (9) are in closed position. THE VALVE IS CLOSED WHEN IT IS PERPENDICULAR TO THE VALVE CORE. Connect water supply and return to the manifold on the PEX Male Threaded Adaptors (10) using a PEX pipe and a PEX crimp ring (not included). Remove all Flow Meter Base Caps (Black) (14) from all Flow Meters (8) by gripping the tabs and snapping it upward over the Flow Meters (8). The Flow Meter Base Cap (Black) (14) is a black protective sleeve that sits on the base of the Flow Meter. Gently unscrew all Flow Meters (8); counter clock wise so 3 threads of the Flow Meter (8) are visible (about 3 turns). If pliers are needed, use carefully in order to avoid breaking the part. You should unscrew only the ones where you are installing a piping loop. Leave the other Flow Meters (8) in closed position. Flow Meters are in closed position when it shows no thread. Do not replace Flow Meter Base Caps (Black) (14) at this stage. Attach a drain hose to the Air Vent and Bleeding Valve (3A) on the Manifold Core with Port Valves (5A) and open the Bleeding Valve completely. Completely close all but one Port Valves (2). Open water source connected to the Manifold Core with Flow Meters (5B). After purging the first loop, close the Port Valve (2) and open the following one. Continue one loop at the time until each loop has been completely purged. Once the last Port Valve is closed, close the purge valve and remove the drain hose from the Bleeding Valve of the Air Vent and Bleeding Valve (3A) unit. Open the Return Ball Valve (Blue) (1). Any remaining air pockets will be eliminated by the water heating source bleeding system within few circulating hours. Step 7: CALIBRATING FLOW METERS As pipe length may vary from loop to loop, it is important to balance the water flow in each loop to ensure proper flow in the whole system. Maintain water flow in the system. Open all Port Valves (2) for each loop to the maximum. Close all Flow Meters (8) completely by turning them clockwise by hand, until all Flow Meters (8) indicate 0 GPM. Do not use pliers or any other tool to turn them. Page 4 of 5
5 To adjust the desired maximum flow rate per loop, gently turn one Flow Meter (8) at the time counter clock wise until required flow (GPM) is achieved. After calibrating all flow meters check that the desired flow is equal in each loop and this is indicated by all Flow Meters (8). Once adjustment is done, replace each Flow Meter Base Cap (Black) (14) on the base of each Flow Meter (8). The cap is replaced correctly when it is snapped on and you cannot turn it. Note that Flow Meters (8) can be completely shut down if a loop is not used. Note: if the loop is not used and there is no pipe connected to it, you must use port cap (not included) to prevent leakage. Step 8: OPERATING THE SYSTEM Use the Port Valves (2) to increase or reduce the water flow in each loop. When a Port Valve (2) is completely closed, the water doesn t circulate in the pipe loop and it does not heat the area. The more the Port Valve (2) is opened, the more heat will be transferred to the area. If the heating system is not required for a long period of time, we recommend to leave the Return Ball Valve (Blue) (1) and Supply Ball Valve (Red) (9) opened and keep the Port Valves (2) completely closed, or accordingly to the plumbing codes, good practices, or the water heating source and pump instructions. The heating source and pump should be completely closed as per their manufacturers instructions. If you need more help or assistance, please contact us at GTGLOBE ( ) Page 5 of 5
MrPEX 1 ½ " Brass Manifold Installation Guide
MrPEX 1 ½ " Brass Manifold Installation Guide Design MrPEX 1 ½" Brass Manifold is made from high quality alloy extruded and chrome plated after machining, and is offered in 2 through 12 loop configurations.
More informationMrPEX 1 ¼ Stainless Steel Manifold. Installation Guide
MrPEX 1 ¼ Stainless Steel Manifold Installation Guide Design MrPEX 1 ¼ Stainless Steel Manifold is made from high quality stainless steel, and is offered in 2 through 12 loop configurations. The manifold
More informationGTFLOW MANIFOLD FEATURES: BENEFITS:
GTFLOW MANIFOLD AND ACCESSORIES GTFlow is our line of manifolds which includes all accessories needed for a complete radiant floor system. GTFlow is made with high quality brass which comes to you preassembled
More informationM-8100EP. Installation Guide ENGINEERED PLASTIC MANIFOLD SERIES. Introduction. A. Assemble Manifold Components
Introduction The Pro Manifolds with Integrated adaptor are designed for use in Hydronic radiant panel heating and cooling applications. They are available in various sizes, configurations, and options
More information1" QickZone Modular Brass Manifold Installation Instructions Parts List
Parts List QHCMKIT5 1" Manifold Supply End Modules with Lock Shield and Flow Meter QHMODAK: Adjustment Key QHMAVKIT5: Manual Air Vent 1" Manifold Return End Modules with Manual Shut Off QHLABELS: Labels
More informationHouse Hydrant Installation Instructions
House Hydrant Installation Instructions Please read all instructions and warnings before installing. WARNING Failure to turn off water supply prior to installation can result in personal injury or damage
More informationManifold Isolation Valves
300 N. Opdyke Rd. Introduction The Stainless Manifolds are designed for use in Hydronic radiant panel heating and cooling applications. They are available in various sizes, configurations, and options
More informationM Installation Guide. PRECISION Manifold Series. Introduction. A. Assemble Manifold Components
Page 1 Introduction The M-8200 Precision Manifolds are designed for use in Hydronic radiant panel heating and cooling applications. They are available in various sizes, configurations, and options with
More informationInstallation Instructions Series
PORTSMOUTH MONOBLOCK LAVATORY FAUCET with Speed Connect Drain Installation Instructions 70.0 7.0 Series 7.0 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature
More informationINSTALLATION INSTRUCTIONS STUDIO S
INSTALLATION INSTRUCTIONS STUDIO S 70.0 MONOBLOCK LAVATORY FAUCET WITH SPEED CONNECT Thank you for selecting American Standard... the benchmark of fine quality for over 00 years. To ensure that your installation
More informationINSTALLATION INSTRUCTIONS PATIENCE
INSTALLATION INSTRUCTIONS PATIENCE 706.8X DUAL CONTROL WIDESPREAD LAVATORY FAUCET WITH SPEED CONNECT Thank you for selecting American Standard... the benchmark of fine quality for over 00 years. To ensure
More informationInstallation Instructions
TROPIC Spread Lavatory Faucet with EverClean Finish & SpeedConnect Drain Installation Instructions 708.80 Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect
More informationOperation and Maintenance Manual
BM / BMA Hydrometers ½ Operation and Maintenance Manual i This manual is intended for use by the users of this equipment. The information contained herein is the property of the Arad Ltd. Dalia and may
More informationInstallation Instructions
BERWICK / BOULEVARD MONOBLOCK LAVATORY FAUCET with Speed Connect Drain Installation Instructions 70.0 7.0 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature
More informationInstallation Instructions Series Series
PORTSMOUTH Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found onlyon American Standard faucets. Recommended
More informationMrPEX 1 ¼ Stainless Steel Manifold Installation Guide
MrPEX 1 ¼ Stainless Steel Manifold Installation Guide Design MrPEX 1 1/4 Stainless Steel Manifold is made from high quality stainless steel, and is offered in 2 through 12 loop configurations. The manifold
More informationInstallation Instructions
TIMES SQUARE Spread Lavatory Faucet with Speed Connect Drain Installation Instructions 8.80 8.8 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only
More informationInstallation / Operation Manual
Installation / Operation Manual Installation Requirements Pressure Range: 10-150 psi Temperature Range: 40-120 F Max Service Flow Rate: 25gpm NOTE: Position filter on a level surface. Filter must be installed
More informationFor assistance call T&M. Tubing and manifolds. installation guide
For assistance call 1.877.338.5493 1 06.17 T&M Tubing and manifolds installation guide 2 Table of contents For assistance call 1.877.338.5493 3 Manifold diagram Page 4 Manifold installation Page 5 Tubing-to-manifold
More informationInstructions. Certifications Chrome less spray Chrome with spray 10-K82-WNCH-AD-Z Chrome less spray 10-K82-WYCH-AD-Z Chrome with spray
Instructions *Image may vary slightly from actual product Tools Required Adjustable Wrench Groove Joint Pliers Pipe Wrench Phillips Screwdriver Pipe Tape or pipe thread compound Safety Tips If you solder
More informationInstallation Instructions
Spread Lavatory Faucet with the Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect
More informationHKV 1 1/4 in. Brass Manifold Product instructions. Construction Automotive Industry
HKV 1 1/4 in. Brass Manifold Product instructions www.rehau.com Construction Automotive Industry SCOPE This guide provides instruction regarding HKV 1 1/4 in. manifold installation and operation. Manifolds
More informationADVANTAGE Annual Preventive Maintenance Instructions
ADVANTAGE Annual Preventive These instructions should be followed to perform preventive maintenance on the Advantage reprocessor. Before commencing work on the reprocessor, ensure that you have the appropriate
More informationManifolds series 73A and 77A. Instruction manual
KAN-therm System Manifolds series 73A and 77A Instruction manual Manifolds 73A and 77A description and principles of operation................. 18 Manifolds series 73A and 77A valves adjustment............................
More informationLEAK TEST PROCEDURE APPLICABLE TO DC3 INTELLI-GRIP LIFTERS MODELS MRT4-DC3, MRTA8-DC3, MRTALP8-DC3 AND PC/P1-DC3 SERIES
LEAK TEST PROCEDURE APPLICABLE TO DC3 INTELLI-GRIP LIFTERS MODELS MRT4-DC3, MRTA8-DC3, MRTALP8-DC3 AND PC/P1-DC3 SERIES TESTING AND MAINTENANCE MUST BE DONE BY A QUALIFIED PERSON KEEP FOR FUTURE REFERENCE
More informationWARNING. Important Notice
CAL (Color AquaLuminator ) Light and Return Water Flow for Above Ground Pools Owners Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION
More informationSAVE FOR CONSUMER INSTALLATION / OWNER'S MANUAL. Single Handle Kitchen Faucet Model # LK2500. Important! You choose the flow rate!
INSTALLATION / OWNER'S MANUAL Single Handle Kitchen Faucet Model # LK500 Important! You choose the flow rate! This faucet ships with an eco-friendly.5gpm flow regulator installed. If you desire higher
More informationSERIN MONOBLOCK LAVATORY FAUCET with
SERIN MONOBLOCK LAVATORY FAUCET with Speed Connect Drain Installation Instructions 0.0 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American
More informationInstructions. Certifications. Two Handle Kitchen Faucet. Tools Required. Maintenance. Safety Tips. Important Points. Things You May Need.
116874 Chrome less 116864 PVD brushed nickel with 0-K8-CYCH-AD-Z Chrome with 0-K8-CYBN-AD-Z PVD brushed nickel with 0-K8-CNCH-AD-Z Chrome less 0-K8-CNBN-AD-Z PVD brushed nickel less *Image may vary slightly
More informationINSTALLATION, OPERATION, & MAINTENANCE MANUAL Models # MM-30, MM-30HT, MM-50, MM-50HT, & MM-50 EXL with Special HP Tool and Special HP EXL Tool
INSTALLATION, OPERATION, & MAINTENANCE MANUAL Models # MM-30, MM-30HT, MM-50, MM-50HT, & MM-50 EXL with Special HP Tool and Special HP EXL Tool INSTALLATION INSTRUCTIONS FOR THE MODEL MM-30 & MODEL MM-50
More informationInstallation Instructions JASMINE Spread Lavatory Faucet with the EverClean Finish & Speed Connect Drain
Installation Instructions JASMINE 80. Spread Lavatory Faucet with the EverClean Finish & Speed Connect Drain Congratulations on purchasing your American Standard faucet with the EverClean finish and Speed
More informationInstallation Instructions
FLUENT Wide Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed
More informationEDGEMERE DUAL CONTROL WIDESPREAD LAVATORY FAUCET INSTALLATION INSTRUCTIONS
EDGEMERE DUAL CONTROL WIDESPREAD LAVATORY FAUCET INSTALLATION INSTRUCTIONS 708.80 Thank you for selecting American Standard... the benchmark of fine quality for over 00 years. To ensure that your installation
More informationInstallation Instructions
CADET Centerset Lavatory Faucet with Speed Connect Drain Installation Instructions Congratulations on purchasing your American Standard faucet with the Speed Connect Drain, a feature found only on American
More informationRSV16 Retro-Fit Cartridge Acorn Controls SV16 Valve Cartridge
ACORN ENGINEERING COMPANY P.O. BOX 2 CITY OF INDUSTRY, CA 1 UNITED STATES OF AMERICA WWW.ACORNENG.COM RSV Retro-Fit Cartridge Acorn Controls SV Valve Cartridge Patented ADA Compliant Ligature and Vandal
More informationLK Manifold RF. Design. Requirements. Documentation
LK Manifold RF Design LK Manifold RF is made of stainless steel, the variants having 2 to 12 floor heating circuits. The manifold is delivered pre-mounted in brackets. The manifold has thermometers on
More informationDP556 Pump. 55:1, Air-operated, Grease. General. Operation. Technical Data. Installation. Mounting with Reinforced Cover (Recommended)
DP556 Pump 55:1, Air-operated, Grease General The DP556 Pump is a compressed air-operated reciprocating piston pump. This high capacity demand pump is compatible with mineral and synthetic grease and suitable
More informationInstallation Instructions 7024
HAMILTON Centerset Lavatory Faucet with EverClean Finish & Speed Connect Drain Installation Instructions 70 Congratulations on purchasing your American Standard faucet with the EverClean finish and Speed
More informationMODEL G300 BRAKE BLEEDER
MODEL G300 BRAKE BLEEDER Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV120716 P/N: 81-0035H THIS PAGE INTENTIONALLY
More informationTWO-STAGE HYDRAULIC PUMP. RWP55-IBT-Air
ORIGINAL INSTRUCTIONS Form No.1000458 5 SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031 Internet
More informationTHANK YOU FOR CHOOSING BATHERBOX GETTING STARTED WHAT S IN THE BOX? N. Northview Ave Sioux Falls, SD 57107
INSTRUCTION MANUAL THANK YOU FOR CHOOSING BATHERBOX You are on your way to creating an unmatched bathing experience both for you and the lucky animal. The BatherBox is designed to save you hours of time
More informationPSR-HP-3000 MANUAL HAND PUMP INTERNAL LIQUID CAPICITY MAXIMUM OUTPUT PRESSURE PsiG (BarG) GALLONS (LITERS) 3000 (207) 5 (19)
PAGE 1 OF 6 P-SERIES HAND PUMP OPERATING INSTRUCTIONS WARNING: PRESSURE TESTING IS INHERENTLY DANGEROUS. STRICT ADHERENCE TO THESE OPERATING INSTRUCTIONS AND INDUSTRY SAFETY PRACTICES COULD PREVENT INJURY
More informationBasin Set INSTALLATION INSTRUCTIONS
P22730-00, P22730-LV, P22730-CC, P22730-BC, P22730-GC, P23100-LV, P23200-LV, P23200-RK, P23200-SK, P23200-SL, P24030-CR, P24030-KL, P24030-CL, P24030-RB, P24030-RL 1 of 6 Thank You For Choosing KALLISTA
More informationInstallation Instructions
Reliant Single Control Centerset Lavatory Faucet with SpeedConnect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard
More informationThe ionpia H 2 Owner s Manual
Hydrogen Enhanced Living The ionpia H 2 Owner s Manual Only from AlkaViva Warning: Incorrect installation and/or operation could void your valuable warranty. Please protect your investment! READ THIS MANUAL
More informationINSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks
INSTRUCTIONS Disassembly To protect against accidental start-up of vehicle, always disconnect the negative battery cable before working on the motorcycle. Failure to disconnect the battery cable could
More informationProduct Information. Brass Manifolds. Version A
Product Information Brass Manifolds Version A Introduction Infloor offers a complete line of brass manifolds for radiant heating applications. This guide explains the how the manifolds work, the setup
More informationFOR TECHNICAL ASSISTANCE
ACORN ENGINEERING COMPANY P.O. BOX 3527 CITY OF INDUSTRY, CA 91744 UNITED STATES OF AMERICA WWW.ACORNENG.COM INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS SV16 TEMPERATURE/PRESSURE BALANCING MIXING
More information6-12 WIDESPREAD 6-12 W. Cleopatra Series INSTRUCTION GUIDE SAVE THIS INSTRUCTION GUIDE
INSTRUCTION GUIDE STEP-BY-STEP ILLUSTRATED INSTALLATION INSTRUCTIONS TROUBLE SHOOTING & REPAIR TIPS 20 YEAR LIMITED WARRANTY PROPER FINISH CARE Read these instructions carefully before installing your
More informationInstallation Manual TWM Performance Full replacement short shifter assembly Civic all trims and models
Installation Manual TWM Performance Full replacement short shifter assembly 2006+ Civic all trims and models Begin the installation by parking on a flat surface, as you will have to engage and disengage
More informationOWNER S MANUAL Model: LG ( ) (15 Gallon Lawn & Garden Trailer Sprayer)
OWNER S MANUAL Model: LG-1500-304 (5301439) (15 Gallon Lawn & Garden Trailer Sprayer) Technical Specifications 15 Gallon Corrosion-Resistant Polyethylene Tank 12 Volt Diaphragm Pump, 2.1 g.p.m. 60 psi
More informationFinal Assembly Instructions: Runaround Cruiser
Final Assembly Instructions: Runaround Cruiser Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationDeck-Mounted Bath Set with Diverter
P24703 2014 KALLISTA THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product. If
More informationKJ-108. Seal Kit Instructions. Weaver Jack Corporation 343 Lawrence Street Adrian, MI 49221
KJ-108 Seal Kit Instructions Weaver Jack Corporation 343 Lawrence Street Adrian, MI 49221 KJ-108 Seal Kit For Use with WA-75A & WA-75B 10 Ton Floor Jacks COMPONENTS S-6615 Piston Rod Packing (3) S-22963
More informationInstallation. Tools. Single Handle Kitchen Faucet With Optional Spray. Maintenance. Safety Tips. Important Points. Need Help? For Model:
Installation Tools - Basin Wrench - Adjustable Wrenches - Pipe Wrench - Screwdriver - Thread Seal Tape - Supply Lines - Protective Goggles - Silicone Sealant - Pliers - Soft Cloth For Model: 673-6809 Single
More informationFleck 2510 Manual Sediment Filter Installation & Start-Up Guide
Clean Water Made Easy www.cleanwaterstore.com Fleck 2510 Manual Sediment Filter Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine
More informationLEAK TEST PROCEDURE MRTALPCH611LDC REMOTE READY LIFTERS W/ 3 BUTTON CONTROL APPLICABLE TO LIFTERS WITH SERIAL NUMBERS GREATER THAN #
LEAK TEST PROCEDURE MRTALPCH611LDC REMOTE READY LIFTERS W/ 3 BUTTON CONTROL APPLICABLE TO LIFTERS WITH SERIAL NUMBERS GREATER THAN # 20100742 TESTING AND MAINTENANCE MUST BE DONE BY A QUALIFIED PERSON
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Randall Single Lever Lavatory and Vessel Faucets Lavatory Model D500C Vessel Model D505C Model D506C Thank you for selecting DXV. To ensure that your installation proceeds smoothly,
More informationCOMMERCIAL. BV & BVM Series Installation Instructions 06/29/15
COMMERCIAL Bray Controls Commercial Division 13788 West Road, Suite 00A Houston, Texas 77041 BCDSales@Bray.com Phone: 1-888-41-79 Fax: 1-888-41-70 www.braycommercialdivision.com BV & BVM Series Installation
More informationINSTALLATION AND MAINTENANCE OF TOP LOADING ARM
INSTALLATION AND MAINTENANCE OF TOP LOADING ARM D TABLE OF CONTENTS 1. INTRODUCTION 04 2. SPECIFICATION OF THE REDLANDS LOADING ARM 04 3. INSTALLING THE LOADING ARM 3.1. Installation Procedures 05 4.
More information3M Overhaul Service Kit
SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 3 in. (77 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20346, 3M Overhaul Service Kit, contains all the replacement parts that naturally wear
More informationPILLOWS DECK-MOUNT BATH FAUCET WITH FLUME SPOUT
PILLOWS DECK-MOUNT BATH FAUCET WITH FLUME SPOUT BEFORE YOU BEGIN NOTES Observe all local plumbing and building codes. Advance planning before installation is crucial. Carefully read the entire instructions
More informationKAN-therm System. Series 71A, 75A, 51A, 55A manifolds. installation and maintenance instructions
instrukcja_rozdzielacz71a-55a_pl_ru_en:print 2010-09-30 14:14 Strona 25 KAN-therm System Series 71A, 75A, 51A, 55A manifolds installation and maintenance instructions Series 71A and 75A manifolds Installation
More informationPRO-BALANCE 1 1/4 IN. BRASS MANIFOLD. Product Instructions
PRO-BALANCE 1 1/4 IN. BRASS MANIFOLD Product Instructions CONTENTS 1. Scope 3 2. Product Overview 3 3. Technical Data 5 4. Mounting the Manifold 7 5. Installing RAUPEX Pipes 8 6. Flushing and Filling Radiant
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MODEL: GRAFTON RH-510 1 REV.A Restoration Hardware Balance Pressure Tub /Shower Set Specification Diagram Ensure that the stop ring () is correctly installed, prior to finished
More informationMercedes E63/CLS AMG Carbon Turbo Intake System Instructions
Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions The goal of Alpha Performance is to provide the highest quality, best performing products available. By utilizing research and development,
More informationWARNING CAUTION. CAUTION Do not exceed 120 psig (8.3 bar) air-inlet pressure.
13966-300-BM SAFETY MANUAL READ FIRST! IMPORTANT: READ THESE WARNINGS AND SAFETY PRECAUTIONS PRIOR TO INSTALLATION OR OPER- ATION. FAILURE TO COMPLY WITH THESE INSTRUC- TIONS COULD RESULT IN PERSONAL INJURY
More informationSAI GM Series Piston Hydraulic Motor Crankshaft Design Radial Piston Motors
SAI GM Series Piston Hydraulic Motor Crankshaft Design Radial Piston Motors www.chinawinches.cn (Dimension: inch) Brief Performance Table of Sai GM Series Piston Hydraulic Motor (Full range GM05- GM9 series)
More information3.1 DISPENSER BLACK SHADOW SERIES. Tools Needed for Mounting SCS Dispenser Hammer
SCS 2 BLACK SHADOW SERIES 3.1 DISPENSER ALWAYS OBSERVE PRODUCT SAFETY AND HANDLING INSTRUCTIONS. ALWAYS DIRECT DISCHARGE AWAY FROM YOU or other persons. ALWAYS DISPENSE CLEANERS AND CHEMICALS AS DIRECTED
More informationPACKING, HANDLING, TRANSPORTING AND STORING MOTORS
PACKING, HANDLING, TRANSPORTING AND STORING MOTORS Make sure that the shaft of the motor is not loaded in any way and is protected from knocks. Axial loads or shocks may easily damage the bearings inside
More informationInstallation Instructions
Installation Instructions To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. P r o d u c t s Luxury Faucets and Accessories Savina Product Numbers
More informationand 1/4 TURN SECOND STAGE REGULATOR TAL 502 (L) Rev. 0 MSA 2005 Prnt. Spec (I) Mat Doc
and 1/4 TURN SECOND STAGE REGULATOR TAL 502 (L) Rev. 0 MSA 2005 Prnt. Spec. 10000005389 (I) Mat. 10064383 Doc. 10064383 REGULATOR COMPONENTS Item Part No. Description 1 MASK MOUNTED REGULATOR ASSEMBLY
More information5000/6000 SERIES BALL VALVES INSTALLATION - MAINTENANCE MANUAL
Date: August 2011 / Page 1 of 6 5000/6000 SERIES BALL VALVES INSTALLATION - MAINTENANCE MANUAL DESIGN The design features three piece construction and a free floating ball allowing ease of maintenance
More informationSecond Stage Regulator - 1/4 Turn
Second Stage Regulator - 1/4 Turn MAINTENANCE AND REPAIR TAL 806 (L) Rev. 6 MSA 2008 Prnt. Spec. 10000005389 (I) Mat. 10042827 Doc. 10000015245 1/4 TURN SECOND STAGE REGULATOR SECOND STAGE REGULATOR COMPONENTS
More informationINSTALLATION MANUAL IMPORTANT CONSIDERATIONS TECHNICAL INFORMATION. Tools you may need
Model: IS203, IS203-1-X Three Way Thermostatic Valve 3/4 Rough and Trim Set INSTALLATION MANUAL U P C C Compliance: ASME A112.18.1 CSA B125.1 IMPORTANT CONSIDERATIONS This product and other additional
More informationInstallation Instructions To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.
Widespread Lavatory Faucet Installation Instructions To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. P r o d u c t s L u x u r y F a u c e
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
AQUALUMINATOR & AQL LIGHT AND RETURN WATER FLOW FOR ABOVE GROUND SWIMMING POOLS INSTALLATION AND USER'S GUIDE Contents SECTION I. IMPORTANT SAFETY INSTRUCTIONS... 2 SECTION II. LAMP HOUSING INSTALLATION...
More informationInstallation and Maintenance Instructions for Morin MRP Pneumatic Rack and Pinion Actuators
for Morin MRP Pneumatic Rack and Pinion Actuators Introduction The Morin MRP Pneumatic Actuator is a compact, rack & pinion design, conforming to Keystone standard or direct mount standards or EN ISO 5211
More informationSachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport
Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,
More informationBEFORE BEGINNING INSTALLATION
COMPLETE CHASSIS FUEL LINE KITS For 1996-2000 Honda Civic Equipped with B-Series Engine INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations
More informationF-4600 INLINE ULTRASONIC FLOW METER Installation and Operation Guide
F-4600 INLINE ULTRASONIC FLOW METER Installation and Operation Guide 11451 Belcher Road South, Largo, FL 33773 USA Tel +1 (727) 447-6140 Fax +1 (727) 442-5699 1054-7 / 34405 www.onicon.com sales@onicon.com
More informationWelker Sampler. Installation, Operation, & Maintenance Manual. Model GSS-4HP
Installation, Operation, & Maintenance Manual Welker Sampler Model GSS-4HP The information in this manual has been carefully checked for accuracy and is intended to be used as a guide to operations. Correct
More informationSection 1: Parts List. Section 2: Replacement Instructions
Page 1 of 6 Section 1: Parts List Components Supplied by EPI (1) Pump Motor (if motor is being replaced) (1) #200 Mechanical Seal (1) Seal Bracket O-Ring (1) Diffuser Seal Tools Required (supplied by others)
More informationR11B EN R11A EN. RackCDU. Service Manual. Edition August 2016 Page 1 of 24 V /8
R11B-1528-02EN R11A-0555-03EN Service Manual - English RackCDU Service Manual Edition August 2016 Page 1 of 24 Version history Issue number Reason for update 1.0 / December 2015 Initial release 2.0 / February
More informationSteam/Water Washdown Units Safety and Operation Installation and Maintenance Instructions
INSTALLATION AND MAINTENANCE INSTRUCTIONS IM-8-002-US October 2016 Steam/Water Washdown Units Safety and Operation Installation and Maintenance Instructions These instructions should be read by the Company
More informationHydroCycle 6" Pro NFT Lettuce Systems
HydroCycle 6" Pro NFT Lettuce Systems Designed to grow healthy plants without soil using mineral-nutrient solutions. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission.
More informationAir / Hydraulic Pump
Form No. 538016 Parts List & Operating Instructions for: 2510A Original Instructions Air / Hydraulic Pump Maximum Capacity: 690 bar (10,000 psi) Description: The 2510A air/hydraulic pump is designed to
More informationLEAK TEST PROCEDURE DC CHANNEL LIFTERS SINGLE VACUUM SYSTEMS TESTING AND MAINTENANCE MUST BE DONE BY A QUALIFIED PERSON KEEP FOR FUTURE REFERENCE
LEAK TEST PROCEDURE DC CHANNEL LIFTERS SINGLE VACUUM SYSTEMS TESTING AND MAINTENANCE MUST BE DONE BY A QUALIFIED PERSON KEEP FOR FUTURE REFERENCE TST-008 Rev. 2013-048 Page 1 of 10 THIS PAGE INTENTIONALLY
More informationApplication Note Xicato XTM LED Module Assembly Instructions Version
Application Note Xicato XTM LED Module Assembly Instructions Version 20150916 General Handling When handling the XTM module, it is important to avoid touching both the phosphor coating on top of the LED
More informationOil Metering Valve. Information and rebuild instructions. #905005
Sig Marine Products #407-204 Cayer St. Coquitlam B.C. Canada V3K 5B1 www.sigmarine.com info@sigmarine.com T: 800 659 9768 Oil Metering Valve Information and rebuild instructions. #905005 Do not plug the
More informationM661 Instruction Manual
M661 Instruction Manual Please inspect your machine carefully upon receipt. Let us know immediately if you note any damage. -IMPORTANT NOTICE- THIS MACHINE IS NOT TO BE OPERATED BY ANYONE UNTIL HAVING
More informationTemperature Sensor Series
GENERAL DESCRIPTION The patented* No. 85026-Series Temperature Sensor contains a two-position valve operated by temperature variations around the integral sensing bulb. It is used to vent or block a pneumatic
More informationINSTALLATION INSTRUCTIONS FUEL RAIL
INSTALLATION INSTRUCTIONS FUEL RAIL MITSUBISHI EVO X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM PREPARING THE VEHICLE:
More informationMilano AUTOMATIC FAUCET
Milano AUTOMATIC FAUCET with Surround Sensor Technology Installation & Maintenance IMPORTANT: PLEASE READ ENTIRE INSTRUCTION BOOKLET BEFORE YOU BEGIN INSTALLATION! Looks Clean - Is Clean. AutoFaucet Parts
More informationInstallation Instructions
COLONY/COLONY SOFT Bidet Faucet and Transfer Valve with Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect drain, a feature found only on American Standard
More informationMAINTENANCE ROAD 2013 WHEELS TECHNICAL MANUAL
2013 WHEELS TECHNICAL MANUAL ROAD CYCLOCROSS PISTA GROUPSET TYPE OPERATION REVISION DESCRIPTION ROAD GROUPSETS CONE / CUP MOVEMENT 002 1/2011 SERVICING FRONT HUB ASSEMBLY PRODUCTS ON WHICH THE PROCEDURE
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) & (3120/3320/3520/3720) HARD SIDED CAB ENCLOSURE (p/n 1JD3520AS) SOFT SIDED CAB ENCLOSURE
More informationSM Valve Installation
INSRUCIONS FOR MODELS SM-12000 Valve Installation OOLS AND SUPPLIES Adjustable Pipe 1 Shut off the water supply to the tub and shower. Verify that the hole sizes and positions in the wall are correct:
More informationInstruction Manual For MrPEX Composite Radiant Manifold
Instruction Manual For MrPEX Composite Radiant Manifold For Radiant Floor Heating and Cooling Applications Read manual before use! Observe all safety information! Keep manual for future use! A Division
More informationProduct Instructions. Mixing Station. Features. Specifications. Materials
Mixing Station The Viega Mixing Station provides supply water temperature modulation when connected to a variety of heat sources such as conventional or condensing boilers, water heaters, or geothermal
More information