Stepper Motor & DC HAT for Raspberry Pi A+, B+ or 2.

Transcription

1 Axial Fans 817 Gearboxes 813 Motors 812 Servos 817 Stepper Motors 812 Arduino Motor/Stepper/ Servo Shield Kit Only Stepper Motor & DC HAT for Raspberry Pi A+, B+ or 2 From only Page 119 G901X Step Pulse Multiplier Only G201X Stepper Motor Controller 10 Micro-step Fixed Res Drive 7A 80V D Only Digital Single Output Bench PSU LED 1x0-30V 0-3A Heatsinks Only Page 825 Page 874 of Electronics Components or for our full range of heatsinks visit

2 Motors BEST SELLER 3V, RPM DC Motor A low-cost miniature DC motor with many applications including models, robotics and educational demonstration equipment. Operating voltage 1.5 to 4.5V DC a PCB Rotates counter-clockwise when viewed from shaft end Solder tag termination 3V DC 0.34A max. No load speed 16,400rpm ± 15% Rated load 8.0 g.cm Rated load current 1.07A max. Rated load speed 13,100rpm ± 12% Length excluding shaft 25mm 20mm 15.1mm Shaft length 9.4mm 2mm 17g approx. MOQ 2 Order code V, 13,100 rpm Miniature Motor 3V 5240rpm A low-cost miniature motor offering a higher stall torque. Ideal for models, robotics, etc. Operating voltage 1.5 to 4.5V DC Rotates clockwise when viewed from shaft end Solder tag termination 3V DC 0.13A max. No load speed 6700rpm ±15% Rated load 10.0 g.cm Rated load current 0.45A max. Rated load speed 5240rpm ±12% Length excluding shaft 26.9mm 23.8mm Shaft length 8.6mm 2mm 28g approx V, 5240 rpm motor Miniature Low Inertia Solar Motor 2V 1540 RPM A low inertia precision solar motor with a starting current making it ideal for low power applications. (2V nominal). Direction: Clockwise Constant volts: 2.0V No load speed rpm: 00 (A): Torque g-cm: 5.5 Output watts:0.05 Stall torque g-cm:11 :24mm :21g Mini solar motor Low Inertia Motor 6V 2700rpm A precision low-inertia motor ideal for low power applications. Direction: Clockwise Nominal volts: 6.0V Operating range: 12V max. No load speed rpm: A Torque: 60g-cm Stall torque: 5.88g-cm :45g V, 2700 rpm motor Miniature Motor 3V 8000rpm A high torque miniature DC motor for higher power requirements. Operating voltage 1.5 to 6.0V DC Rotates clockwise when viewed from shaft end Solder tag termination 3V DC 0.23A max. No load speed 9000rpm ±15% Rated load 10.0 g.cm Rated load current 0.63A max. Rated load speed 8000rpm ±12% Length excluding shaft 30.5mm 24.2mm Shaft length 12mm 2mm 42g approx V, 8000 rpm motor Tel: Fax: V DC Model Tuning Motors A range of 7.2V electric motors for upgrading or tuning radio controlled models. The motors are ideally suited to replacing the model s standard engine to gain more power or speed. Replaceable carbon brushes Supplied complete with operating instructions Dimensions (ø x L) 36mm x 54mm 58.1% Idle speed 192rpm Manufacturer part no Motor shaft length 11mm Nominal voltage 7.2V Operating voltage 7.2Vdc Output power of electric motor 36.75W 3.175mm Turns g Dimensions (ø x L) 36mm x 54mm 62.1% Idle speed 18924rpm Manufacturer part no Motor shaft length 11mm Nominal voltage 7.2Vdc Operating voltage 7.2Vdc Output power of electric motor 49.61W 3.175mm Turns g Dimensions (ø x L) 36mm x 54mm 67.8% Idle speed 787rpm Manufacturer part no Motor shaft length 11mm Operating voltage 7.2Vdc Output power of electric motor 77W 3.175mm Turns g V 12,200rpm Miniature Motor A 3V miniature motor ideal for low voltage applications. Operating voltage 1.5 to 4.5V DC Applications include motorised toys, models, etc. Rotates clockwise when viewed from shaft end Connection is by means of 2.8mm fast-on connectors, or by soldering 2mm 3V DC 0.34A max. No load speed 15,000rpm ±15% Rated load 10.0 g.cm Rated load current 1.17A max. Rated load speed 12,200rpm ±12% Length excluding shaft 25mm 21mm Shaft length 10mm 2mm 19g approx. MOQ 5 - In Multiples of 5 Order code V, 12,200 rpm Self Adhesive Motor Mount our range of miniature motors. Base has self adhesive surface for easy mounting of the motor as required Colour may vary Supplied in packs of Motor mount ,292 rpm ,924 rpm ,787 rpm Stepper Motors Step Angle Stepper Motor A 12V bi-directional 4-phase unipolar permanent magnet stepper motor. Applying the correct electrical pulse sequence to the windings of the motor results in a 1.8 step angle rotation of the spindle (200 steps per revolution). Number of steps and speed are determined by frequency of input signal applied Suitable for many control applications where a medium torque motor is required 5mm shaft diameter Step angle 1.8 Holding torque 830gf/cm (8.14Ncm) min. Phase (coil) resistance 75 /phase ±10% Current per coil 160mA Nominal voltage 12V Output shaft 5mm dia. Stepper motor Page 864 Stepper Motor Control/ Driver

3 2 Phase Bipolar Stepper Motor 12V A 2 phase bi-polar stepper motor with a 7.5 step angle rotation of the spindle. Number of steps and speed are determined by the frequency of the input signal applied 3mm shaft diameter Step angle 7.5 full step No. of phases 2 12V DC Rated current 0.48A/phase Insulation class E Ambient temperature 10 C to +50 C Coil temperature 115 C Operating humidity 20% to 90% RH (no condensation) Life span >3000 hours min. 3mm 125g Stepper motor Mini Hybrid Stepper Motor Size 11 A high torque stepper motor suitable for heavy duty applications. By applying the correct electrical pulse sequence to the windings of the motor results in a 1.8 step angle rotation of the spindle. Number of steps and speed are determined by the frequency of the input signal applied Lightweight Compact size Low inertia High accuracy 6 leads for greater control 5mm shaft diameter Rotor inertia Detent torque Insulation class Step accuracy Stepper motor size g-cm² 100g-cm B Angular deviation is ±5% of one step 150g sales@rapidonline.com Size 23 Hybrid Stepping Motor 1.8 The hybrid is probably the most widely used of all stepping motors. The hybrid consists of a multi-phased toothed stator and a three part rotor. These high torque stepper motors are suitable for heavy duty applications. By applying the correct electrical pulse sequence to the windings of the motor results in a 1.8 step angle rotation of the spindle. High torque output Number of steps and speed are determined by the frequency of the input signal applied Step angle 1.8 Available in single stack, two stack and three stack options Single stack available with 4 leads Double and triple stack options available with 8 leads for exceptional control The size 23 motor and drive are contained in a compact aluminium heatsink housing Long life and high reliability Order code Step angle 1.8 Step angle Holding torque 7N-cm Step angle 5% 5% 5% No. of leads 6 accuracy Phase current 0.95A Phase current 2.1A 1.0A 3.0A Phase resistance 3.4 Phase resistance Phase inductance 1.6mH Phase inductance 2.1mH 10mH 2.1mH Rotor inertia 12g-cm² Holding torque - 80Ncm 125Ncm Detent torque 50g-cm unipolar Insulation class B Holding torque 50Ncm 100Ncm 160Ncm Step accuracy Angular deviation is ±5% of one step bipolar 140g Detent torque 2.2Ncm 4.0Ncm 7.0Ncm Rotor inertia 135g cm² 260g cm² 460g cm² Mass 0.42kg 0.6kg 1.0kg Insulation class B B B Stepper motor size Single Single Number of leads Mini Hybrid Stepper Motor Size 14 A high torque stepper motor suitable for heavy duty applications. By applying the correct electrical pulse sequence to the windings of the motor results in a 1.8 step angle rotation of the spindle Number of steps and speed are determined by the frequency of the input signal applied Low noise Low inertia High accuracy 6 leads for greater control 5mm shaft diameter Unipolar voltage 8V Step angle 1.8 Holding torque 8N-cm No. of leads 6 Phase current 0.76A Phase resistance 10.5 Phase inductance 4.8mH Two stack hybrid Single stack hybrid Solar Motor Drive A miniature gearbox and solar motor which provides a gear ratio of 27:1 providing approximately 25 revs. per minute at 0.5 volts. Final output via 2mm shaft Motor operating range 1.5 to 4.5V Gearbox dimensions 36 x 15mm Gearboxes Solar motor drive Motor and Gearbox 1:0 A low-cost miniature DC motor suitable for many applications including models, robotics and educational demonstration equipment. Solder tag termination Nominal voltage: 6V DC Direction of rotation: Bidirectional Change of polarity changes the direction of the motor Gear ratio: 1:0 Overall dimensions excluding output shaft 48 x 47 x 24mm Motor and gearbox Single and Dual Output Shaft Inline Motor and Gearbox 1:200 A choice of either dual output shaft or single output shaft inline motor and gearbox assemblies. The gearbox delivers a ratio of 1:200 and is made from high quality plastic. Ideal for use in the construction of robotics and other models. All you need to do is add wheels, hubs or tracks. Available with dual or single output shaft Gear Ratio: 1:200 Power: 3 to 12V DC Single motor Without loading: mA / rpm Output torque: 2-12kgf.cm : 31.9g Size 68 x 20mm Dual output shaft motor Single output shaft motor BEST SELLER 120:1 Inline Motor and Gearbox This economy motorised 12V DC motor. The output shaft is 5.5mm diameter and of between rpm depending on voltage used. Smooth running 3x mounting holes Ideal for small educational projects including fairgrounds and robots : mA Under load at 6.0V: Motor output turning power is 1.8kgf.cm Dimensions 7(L) x 2(W) excluding shaft x 2(W)cm : 30g Motor and gearbox

4 Twin Motor Gearbox Kit This twin motor gear box uses a two motor system to provide power and speed to turn the round shaft in two different directions. The gear box is made from high quality plastic. Use this gear box and motor set to construct mechanical toys and robotic products. Two battery powered motors are included. The easily adjusted gearboxes can be used with a gear ratio of 1:60, 1:120 or 1:288. Ideal for hobbies and education projects Two motor and gearbox sets to have wheels running in different directions 3 different gear ratios for out of your choice 3V motors Battery operated 17mm radius wheels with tyres Drive shaft diameter 2mm (approx) All other necessary parts included Easy to follow instruction manual included Assembled dimensions 76.5 x 66.5 x 36.5mm (W x D x H) 10+ Twin motor gearbox kit Clunk Click Gearboxes This worm-drive gearbox consists of an MM28 motor and output shaft that simply click into place in the plastic housing. Ideal for is required Perfect for student based projects including robots and buggies Available in a range of colours Black Blue Yellow Red Green Solar Motor Worm Drive Gear Box A worm drive gearbox in an aluminium housing powered by a solar motor. Shaft length 125mm approx. Worm drive gearbox MD25 12V 2.8A Dual H-Bridge for EMG30 Gear Motors Serial/I2C Order code mm 5mm Hub Mounts EMG30 Drive Shaft Order code Worm Drive Gearbox with Motor A robust worm-drive gearbox powered by an MM28 motor (included). torque output is required Ideal for student based projects including robots and buggies Motor operating voltage 3V 6V Motor speed 3V no load 9,700rpm 6V no load 17,100rpm Motor stall torque 1g-cm 0g-cm Gearbox ratio 42:01:00 42:01:00 Axle diameter 3mm 3mm Axle length 125mm 125mm Fixing holes 4 x 4mm 4 x 4mm Overall dimensions of box + motor 35(W) x 40(H) x 60(L)mm Worm drive gearbox D Multi-Ratio Gearbox and Motor Tel: Fax: A multi-ratio gearbox available supplied fully assembled or in kit form. Supplied with drive motor which operates on 1.5 or 3.0 volt DC power sources Suitable for battery or transformer operation Sturdy, simple and versatile design Suitable for a host of uses from powering models and robots to teaching the principles of mechanics Current consumption depends on load but is within the range 0.2 to 0.8A Output shaft is 3mm diameter mounting RPM RPM Ratio 1.5V 3V 04:01: :01: :01: :01: :01: :01: Gearbox (kit form) Gearbox (assembled) Multi-ratio Gearbox and Motor A multi-ratio gearbox supplied in kit form which allows a range of different transmission ratios from 5:1 to 3125:1 to be constructed. Possible ratios: 5:1, 15:1, 25:1, 45:1, 125:1, 243:1, 625:1, 1125:1 and 3125:1 Included in the kit is a medium torque motor which will operate from 1.5V to 4.5V DC Easy to mount to any surface with the slots that are provided in the mounting plates Output shaft is 3mm diameter Ideally suited to many projects within education Supplied with full instructions on assembly and gearbox ratios Multi-ratio gearbox Geared Motor Accessory Kit A kit containing a useful selection of mechanical parts, ideal for the construction of motorised models, robots, buggies, technology projects, etc. Motorised gearbox Wheels Hardware Gears Rack and pinion Perforated metal sheet and strips Axles/shafts Nuts Bolts and washers Chain and sprockets Worm drive Toggle switch Size D 1.5V zinc-chloride battery and battery box 5+ Geared motor kit EMG30 Motor with Gearbox and Integrated Encoder The EMG30 is a 12V motor and 30:1 reduction gearbox in a single unit giving a 1.5 to 200rpm output speed. It also has a built-in hall-effect motor encoder which gives precise control. Terminated with a 6-way JST connector for easy connection Mounting bracket available separately ( ) Can be controlled via I2C using the MD25 driver 12V Rated torque 1.5kg/cm Rated speed 170rpm Rated current 530mA No load speed mA Stall current 2.5A Rated output 4.W Encoder counts per o/p shaft turn 360 EMG30 Motor

5 815 Fixed Ratio mm Epicyclic Geared Motor (RE944) This range is designed for smaller industrial and modelling applications. Due to its size and power it is very popular quality 3 pole motor with carbon brushgear. It is of reduction. The output shaft is 4mm diameter with a key For speed regulation see PWM panel mounted speed regulator (see order code ) Designed for heavy duty industrial and model applications. MFA/Como 944D series Motor output at max Rated Torque (g.cm) Mftrs. part no. Order code 4:1 ratio 6 to 12V D :1 ratio 6 to 12V D :1 ratio 6 to 12V D :1 ratio 6 to 12V D (3V) (6V) (9V) 4:1 ratio :1 ratio :1 ratio :1 ratio :1 Epicyclic motor :1 Epicyclic motor :1 Epicyclic motor D Series Fixed Ratio 25mm Spur Geared Motors Suitable for light industrial, educational, modelling and R&D applications. They are of motors with carbon brushgear. Available in 1.5-3V or 12-24V options, they have 4mm diameter For speed regulation see panel mounted PWM speed regulator (see order code ). (Not for use below 6V operation) Designed for heavy duty industrial and model applications. MFA/Como 918D series Technical specification Motor Torque (max. output (max. Mftrs. part no. (g.cm) (W) Order Code 15:1 ratio 1.5 to 3V D :1 ratio 12 to 24V D :1 ratio 1.5 to 3V D :1 ratio 12 to 24V D :1 ratio 1.5 to 3V D :1 ratio 12 to 24V D :1 ratio 1.5 to 3V D :1 ratio 12 to 24V D :1 ratio 1.5 to 3V D5001/ :1 ratio 12 to 24V D500112/ :1 ratio 1.5 to 3V D :1 ratio 12 to 24V D Ratio Order code :1 1.5 to 3V :1 12 to 24V :1 1.5 to 3V :1 12 to 24V :1 1.5 to 3V :1 12 to 24V :1 1.5 to 3V :1 12 to 24V :1 1.5 to 3V :1 12 to 24V :1 1.5 to 3V :1 12 to 24V D Series Fixed Ratio 32mm Epicyclic Geared Motor (RE 385 Motor) Suitable for light industrial, educational, modelling and R&D applications. This combination of motor and gearbox has particular application where high torque with lower current consumption is required. It has a high quality 5 pole motor with carbon brushgear. It is of metal construction with a 6mm diameter output For speed regulation see panel mounted PWM speed regulator, (see order code ) Designed for heavy duty industrial and model applications. MFA/Como 940D series Motor output (max. Torque (max. Mftrs. part no. Order Code 5:1 ratio 6 to 15V D :1 ratio 4.5 to 15V D :1 ratio 7 to 15V D :1 ratio 8 to 15V D :1 ratio 9 to 15V D :1 ratio 4.5 to 15V D (6V) (9V) (15V) 5:1 ratio :1 ratio :1 ratio :1 ratio :1 ratio :1 ratio :1 Epicyclic motor :1 Metal gearbox :1 Metal gearbox :1 Metal gearbox (1.5V) (3V) (6V) (18V) 15:1 ratio 1.5 to 3V :1 ratio 12 to 24V :1 ratio 1.5 to 3V :1 ratio 12 to 24V :1 ratio 1.5 to 3V :1 ratio 12 to 24V :1 ratio 1.5 to 3V :1 ratio 12 to 24V :1 ratio 1.5 to 3V :1 ratio 12 to 24V :1 ratio 1.5 to 3V :1 ratio 12 to 24V (24V) RD02 12V Complete Robot Drive System Order code sales@rapidonline.com 815

6 816 Fixed Ratio 35mm Spur Geared Motor (RE 540/1 Motor) Suitable for light industrial, educational, modelling and R&D applications. This range offers a wide variety of ratios with a quality high torque 3 pole motor with carbon brushgear. They are of metal construction with a 6mm diameter For speed regulation see panel mounted speed regulator (see order code: ) (Not for use below 6V operation) Designed for heavy duty industrial and model applications. MFA/Como 919D series Motor output (W) Rated torque (g.cm) Mftrs. part no. Order code 6:1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D (6V) (9V) (15V) 6:1 ratio :1 ratio :1 ratio :1 ratio :1 ratio :1 ratio :1 ratio :1 ratio :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor :1 Metal gearbox Fixed Ratio 35mm Spur Geared Motor (RE 385) Central Output Shaft Suitable for light industrial, educational, modelling and R&D applications. This unit has a high quality 5 pole motor with carbon brushgear. It differs from the standard 35mm range due to the central output shaft and range of alternative reduction ratios. This range has particular application where high torque requirements with lower current consumption are at a premium. It has a 6mm For speed regulation see panel mounted speed regulator (see order code: ) Designed for heavy duty industrial and model applications. MFA/Como 970D series Motor output at Rated torque (g.cm) Mftrs. part no. Order code :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor :1 Spur geared motor Fixed Ratio 42mm Epicyclic Geared Motors (RE 975) Suitable for medium duty industrial applications. This range is capable of delivering higher torques. They boast high quality 5 pole motors, heavy duty carbon brushgear, with the output shaft running in a ball race. They are of metal construction. They have an 8mm output shaft with For speed regulation see panel mounted speed regulator (see order code: ) Designed for heavy duty industrial and model applications. MFA/Como 975D series Motor output at Rated torque (g.cm) Mftrs. part no. Order code 4:1 ratio 6 to D :1 ratio 6 to D :1 ratio 6 to D (6V) (9V) 4:1 ratio :1 ratio :1 ratio :1 Epicyclic motor :1 Epicyclic motor :1 Epicyclic motor D2 Series PWM / Speed Regulator Modules These regulators from the MFA 919D2 range, have variable outputs providing smooth, progressive speed control from min to max, ideal for use in controlling motors and geared motors. They can also provide a dimmer facility for low voltage lighting circuits (6 to 15V only). They employ Pulse-Width Modulation (PWM) circuitry, giving a constant voltage output. Speed control is achieved by varying the width of the output pulse. Maximum rated output is 3A constant, (5A peak). The modules operate from an input voltage of 6 to 15V DC from a non-digital power supply, i.e., a battery or a linear power supply. Pulse width modulated output provides torque maintenance and proportional output control Small, compact, robust construction for versatility and reliable service Input voltage 6 to 15V DC Output voltage 0 to 15V DC Output current 3A continuous, 5A peak Modulation frequency 1136 to 1250Hz MFA 919D2 series Note: supply and output cables must be trimmed to 21cm to meet current EMC regulations Free Panel mount :1 ratio 6 to 15V D :1 ratio 6 to 15V D :1 ratio 6 to 15V D :1 ratio 6 to 15V D :1 ratio 6 to 15V D :1 ratio 6 to 15V D (6V) (9V) (15V) 6:1 ratio :1 ratio :1 ratio :1 ratio :1 ratio :1 ratio Same day despatch GUARANTEED! On all orders for in-stock items placed between 8am and 7pm Monday to Friday 816 Tel: Fax:

7 Bevel Gearbox 1:1 Gear Ratio These drives are used primarily to transmit power at 90 degrees. The unit has steel gears and shafts running in ballraces and sintered bronze bearings. 1:1 gear ratio Lubricated for life Designed for rugged service life 1 ball race and S B bearing per shaft strength 4 pre-drilled mounting holes Gear Input speed Case Backlash Mild steel: BS rpm max. 1 degree approximately 5+ Bevel gearbox D Series Spur Geared Motor Single Ratio Metal Geared 35mm A range of high quality motors that feature single ratio metal gearboxes with sleeved bearings, enabling the transfer of high amounts of torque from the motor, through the spurred gears, to the 6mm keyed output with carbon brushes and sintered bronze bearings. This robust motor and gearbox is designed for use in heavy-duty industrial applications. Mounted on a 1mm thick plated steel bracket this range of motors, available in a selection of ratios, are ideal for when a lower current consumption is required. Designed for heavy duty industrial and model applications. Robust construction Operating voltage 6 to 15V ø35mm High quality motor Keyed output shaft ø6mm MFA/Como 950D series Motor Torque (max. Mftrs. part Order Code output (max. no. (g.cm) (W) 11:1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D :1 ratio 4.5 to 15V D (6V) (9V) (15V) 11:1 ratio :1 ratio :1 ratio :1 ratio :1 ratio :1 ratio :1 Geared motor :1 Geared motor :1 Geared motor :1 Geared motor :1 Geared motor :1 Geared motor Servos Tower Pro SG90 Mini Servo The Tower Pro SG90 Mini Servo is a low- servo ideal for use in radio-controlled models and for interfacing with microcontroller systems like Arduino, Raspberry Pi, PICAXE, etc. Size: 23 x 12.2 x 29mm Low-cost, high quality Supplied complete with control horns and mounting screws Tower Pro type SG90 Dimensions 23 x 12.2 x 29mm Operating voltage 4.8V Stall torque 1.8kg/cm (4.8V) Operating speed 0.1s / 60 (4.8V) Dead band width 10μs Temperature range 0 to 55 C 9g Mini servo BMS-410C Plastic Gear JR Standard Servo Analogue Servo The Modelcraft BMS-410C Standard Servo is not only economical, but ideal for many applications in Radio Control modelling owing to its standard dimensions. It is also compatible with microcontroller systems such as PICAXE, Arduino and Raspberry Pi. Standard dimensions Includes control horn and screw Modelcraft type BMS-410C Manufacturer part No. BMS-410C Servo type Standard servo Connector system JR Gears Plastic Servo technology Analogue servo Servo time 6V / 7.4V 0.15sec/ 60 Servo time at 4.8 V 0.17sec/ 60 Servo time at 6 V 0.15sec/ 60 Servo torque at 4.8 V 35Ncm Servo torque at 6 / 7.4 V 44Ncm Servo torque at 6 V 44Ncm Stroke time at 4.8 V 0.17sec/ 60 / 0.15sec/ 60 Length 40.5mm Width 20mm 38g Plastic gear servo Servo Mount Kit Modelcraft mounting kit for servos with a hole distance of 10mm in the bracket. Servo width maximum 20mm Servo height maximum 30mm up to bracket Manufacturer part no. NO. 79 Servo Mount Axial Fans 40mm Low Axial Fans AD4010 Series The AD4010 series is a low-cost range of lowvoltage fans offering low Frames and impellers are manufactured in black UL94V-0 glass Fitted with 300mm UL and TUV approved 5V DC 12V DC Input current 0.11A 0.08A Power 0.55W 0.96W Speed (rpm) Noise dba 1m Operating temperature 10 C to +70 C 10 C to +70 C Dimensions 40 x 40 x 10mm(FC 32 x 32mm) 40 x 40 x 10mm(FC 32 x 32mm) Adda type AD0405MS-G70 AD0412MS-G V DC V DC mm Low Noise Axial Fans Low voltage DC medium speed axial fans. Quiet operation strengthened plastic fan Only operates when polarity is correct 310mm 28AWG leads 25g UL, VDE, CSA and CE approved Papst 600 F series Input voltage 12V DC 24V DC range 11.5V to 13.2V DC 21.6V to 26.4V DC Power input 1W 1.1W 17.1m3/h 17.1m3/h Speed 3900rpm 3900rpm Noise 27dB (A) 27dB (A) Life expectancy >50,000 hours >50,000 hours Temperature range 20 C to +70 C 20 C to +70 C Dimensions 60 x 60 x 15mm 60 x 60 x 15mm Papst type 612 F 614 F Order code 1+ 24V SK482100SA + 4XTHFU2 Heatsink SK SA + 4X THFU 2 Order code sales@rapidonline.com 817

8 818 80mm Low Axial Fans The AD8025GL series is a range of low-cost, voltage DC high speed axial fans. Fitted with sleeve bearings Life expectancy >50,000 hours Frames and impellers are manufactured in UL94V-0 glass UL, CSA and TUV approved. 12V DC 24V DC Input Current 0.25A 0.16A Power 3W 3.8W Speed (rpm) Noise dba 1M 10 C to +70 C 10 C to +70 C Adda AD0812HS-A70GL AD0824HS-A706L V V mm Low Axial Fans The AD12025GL series is a collection of low voltage DC medium with sleeve bearings (life expectancy >50,000 hours). Frames and impellers are manufactured in UL94V-0 polyester Fitted with 280mm UL, CSA and TUV approved 12V DC 24V DC Input Current 0.34A 0.2A Power 4.08W 4.8W Speed (rpm) Air Flow (cu ft/min) Noise dba 1m Operating Temperature 10 C to +70 C 10 C to +70 C Adda AD1212MS-A71GL AD14MS-A71GL V V mm 230V Mains Axial Fans High-speed, mains with copper sleeve or ball bearings. Impeller manufactured polyester UL and TUV approved See this section for suitable guards. Order code Frame size 120 x 120 x x 120 x 25mm Frame material Plastic Aluminium alloy Adda type AA1282HX-AW-(CF) AA1252MB-AT Bearing type Sleeve Ball 230V AC 230V AC Frequency 50Hz 50Hz Current 0.12A 0.10A Power 16.0W 21.6W Termination Wire Tags Rated speed 2600rpm 00rpm Noise level 42.2dB 38.7dB 550g 340g Sleeve bearing Ball bearing Cooling Fan Guards of fans. Nickel-chrome plated steel mm cm mm mm mm mm Easy ways to order The fastest & easiest way to order is ONLINE 24 hours a day! Quick order form Live help Save paper go green Fast product search Latest prices and stock levels Ability to pay by credit/debit card or on account Orderline (Between 8.00am and 7.00pm, Monday to Friday, 9.00am to 5.00pm Saturday) sales@rapidonline.com education@ rapidonline.com Fax Post Rapid Severalls Lane, Colchester Essex C04 5JS 60 x 60 x 15/25mm DC Axial Fans 12V/24V, Ball/Sleeve Bearing Order code x 80 x 25mm DC Axial Fans 12V/24V, Ball/Sleeve Bearing Order code Tel: Fax: