Pan Car Setup and Troubleshooting

Size: px
Start display at page:

Download "Pan Car Setup and Troubleshooting"

Transcription

1 Pan Car Setup and Troubleshooting Problems can come up in the midst of competition. Either the car is not handling properly on the track or there are problems with equipment. Troubleshooting problems should be performed in a methodical manner. Work patiently and always make a single change at a time and observe the result(s) of that change. Also take good notes of the changes and the resulting effects. Over time, you will develop enough experience and knowledge to readily recognise the root cause of a problem and correct it. Description of Problem Possible Cause of Problem Car is oversteering Rear tire compound is too hard. Front tire compound is too soft. Front tire diameter is too large. Front suspension springs are too soft. Rear pod movement is too tight. Grease on the rear friction damper plates is too thick. Spring tension on the coil damper or rear shock absorber is too high. Spring tension on the friction damper plates is too high. Viscosity of oil in rear shock absorber is too high. Ball differential setting is too tight. Ball differential setting is too loose. Ball differential is damaged. Thrust bearing in the ball differential is not slipping properly. Corrective Measure Change to softer rear tire compound. Change to harder front tire compound. Reduce the front tire diameter. Remember to re-adjust the ride height. Change to stiffer front springs. Loosen the rear pod (T-bar to main chassis) screws to increase rear pod travel without excessive side to side movement. For even better rear pod movement and control, you can switch to an optional ball mount suspension set. Apply thinner grease on the rear friction damper plates to increase movement of the rear pod. For even smoother response, you can switch to Teflon friction damper plates. Decrease the spring tension by removing spacers or switch to a softer spring to transfer the driving load to the rear end. Also, lightly grease the coil damper shaft for smoother movement. Switch to softer springs to decrease the amount of compression applied to the friction damper plates. For smoother response and easier adjustments, switch to using an adjustable friction damper post assembly. Change to a lower viscosity oil in rear shock absorber. Re-adjust the ball differential to the proper setting. Adjust the rear right axle nut to tighten the ball differential setting and decrease slippage on acceleration. Replace damaged ball differential parts. Replace thrust bearing assembly with a properly oiled one piece thrust bearing for smoother cornering response.

2 Car is understeering Rear center of gravity is too high. Rear wing down force is too low. Front wing down force is too high. Lower the rear end center of gravity using an adjustable ride height gear case to raise the rear axle ride height. Change to a rear wing with three wings (instead of two for increased wing surface area) and/or a higher wing angle. For improved rear wing down force, a rear diffuser set will improve the airflow over the rear wing for higher down force. Change to a smaller front wing with a lower angle. Toe-out angle of front tires is too large. Toe-in front wheels and increase toe-in angle as Front tires experience "edge bite" on hard cornering. Steering servo is too fast in response. Front tire compound is too hard. Front tire diameter is too small. Rear tire compound is too soft. Front suspension springs are too stiff. Chassis flexes too much. Rear pod movement is too loose. Grease on the rear friction damper plates is too thin. Spring tension on the coil spring damper or rear shock absorber is too low. Viscosity of oil in rear shock absorber is too low. Ball differential setting is too tight. Front end ride height is higher than rear end ride height. Weight distribution is lighter at the front end. Round the shoulder of the front tires. Trim steering response if possible. Change to softer front tire compound. Change the front tires to a larger diameter tire set or reduce the diameter of the rear tires. Change to harder rear tire compound. Change to softer front springs. Increase chassis stiffness by changing from the stock chassis plate to a hard carbon-type chassis plate or add the optional FRP upper chassis set (Tamiya Part No ). Tighten the rear pod (T-bar to main chassis) screws to limit rear pod travel. Apply thicker grease on the rear friction damper plates to slow movement of the rear pod. Increase the spring tension with additional spacers to transfer the driving load to the front end. Change to a higher viscosity oil in rear shock absorber. Adjust the rear right axle nut to loosen the ball differential setting and slightly increase slippage on acceleration. Increase rear end ride height using an adjustable ride height gear case to increase front end steering. Reduce weight of rear end and/or move weight distribution forward. You can also switch to a different chassis that allows repositioning of the batteries for better weight distribution.

3 Car does not turn in either direction evenly. Car steering is unstable on straight-aways Front wing down force is low. Toe-in angle of front wheels is too large. Steering servo is too slow in response. Chassis is tweaked. Servo horn neutral position is not set properly. Steering trim for neutral position of the radio transmitter is not properly set. Change to a larger front wing with a higher angle. Toe-out front wheels and decrease toein angle as A slight toe-out may be necessary. Change to a faster steering servo. Adjust suspension settings to remove chassis tweak. Set the servo horn in neutral position with equal steering arm length. Adjust steering trim with radio transmitter steering in neutral position. whichever needs adjustment. Servo is not firmly secured to the Servo saver is worn or loose. Bent steering Uneven tire wear. Uneven bearing wear. Secure the servo to the chassis with glass tape and servo tape. Tighten the servo saver to the servo or replace servo saver Replace and/or true tries to even diameters on each side, both front and rear as Replace worn bearings. whichever needs adjustment. Tires are not glued properly. Front tires are in toe-out condition. Inadequate toe-in angle. Wheel is not firmly secured with lock nut. Servo is not firmly secured to the Glue the tires securely. Adjust front tires for toe-in condition. Increase toe-in angle. Tighten the lock nut to hold the wheel in position. Secure the servo to the chassis with

4 Uneven tire wear Servo saver is worn or loose. Steering trim for neutral position of the radio transmitter is not properly set. Steering blocks are creating oversensitive steering response. Uneven tire wear. Uneven bearing wear. Bent steering Too much play in front end Uneven front spring tension or length. T-bar mounting screws are loose. Countersunk T-bar mounting holes are damaged. Radio interference is causing the steering servo to glitch. Uneven front spring tension or length. Unbalanced wheels. glass tape and servo tape. Tighten the servo saver to the servo or replace servo saver Adjust steering trim with radio transmitter steering in neutral position. Change to offset steering blocks. Replace and/or true tires to even diameters on each side, both front and rear as Replace worn bearings. Replace excessively worn components as Either replace the shorter spring or place a greater preload on it with spacers. Tighten T-bar mounting screws as Replace the T-bar and mounting screws. Identify and eliminate source of radio interference (also see "Radio transmitter is not working." Either replace the shorter spring or place a greater preload on it with spacers. Balance the wheels using lead tape used for balancing golf clubs.

5 whichever needs adjustment. Car ride is very bumpy Bent steering Rear axle intermittently seizes. Unbalanced wheels. Wheel is not firmly secured with lock nut. Tires are rubbing against other Both front and rear tire compounds are too hard. Spring on damper unit is too stiff. Damper fluid is too viscous. Friction damper plate grease is too viscous. Too much play in front end Clean and lubricate rear axle assembly and replace bearings as Balance the wheels using lead tape used for balancing golf clubs. Tighten the lock nut to hold the wheel in position. Increase tire clearance for free movement. Change to softer tire compounds for the front and rear. Replace damper spring with a softer spring. Replace damper fluid with a lower viscosity fluid. Replace friction damper plate grease with a thinner grease. Replace excessively worn components as Too much play in rear end Replace excessively worn components as Worn spur or pinion gear teeth. Worn motor armature. Replace worn gear and properly set gear mesh. Replace any worn armature components as

TIPS TO FINAL ASSEMBLY Radio installation. The Electronic speed control (ESC) and the receiver need to be mounted onto the chassis, using double sided

TIPS TO FINAL ASSEMBLY Radio installation. The Electronic speed control (ESC) and the receiver need to be mounted onto the chassis, using double sided TIPS TO FINAL ASSEMBLY Radio installation. The Electronic speed control (ESC) and the receiver need to be mounted onto the chassis, using double sided tape (not supplied.) Mount the ESC first on the chassis

More information

ROLL CENTER You can adjust the front and rear roll centers of the XB8 by changing the mounting locations of various components.

ROLL CENTER You can adjust the front and rear roll centers of the XB8 by changing the mounting locations of various components. Your XRAY XB8 luxury nitro buggy is a top competition, precision racing machine that features multiple adjustments that allow you to set up for any track condition. The XB8 includes innovative set-up features

More information

Contents. # HUDY Caster Clip Remover Tool. # HUDY Chassis Balancing Tool. # HUDY 3mm Turnbuckle Tool

Contents. # HUDY Caster Clip Remover Tool. # HUDY Chassis Balancing Tool. # HUDY 3mm Turnbuckle Tool Contents Introduction 2 Radio Adjustments 3 Speed Control (ESC) Adjustments 3 Connecting the Motor 3 Motor Gearing 3 Rollout 5 Differential Adjustment 5 Tightening the Differentials 6 Loosening the Differentials

More information

A7741 Truggy Wheel, Yellow

A7741 Truggy Wheel, Yellow STEP H-01 Tire Mounting BAG H 1 2 A7780B XTT Tire, Blue Truggy Foam Insert Only sold with Tires A7741 Truggy Wheel, Yellow STEP H-02 Tire Gluing The Tires need to be glued to the wheels. This can be done

More information

ABC HOBBY ORIGINAL RADIO CONTROL CAR

ABC HOBBY ORIGINAL RADIO CONTROL CAR ABC HOBBY ORIGINAL RADIO CONTROL CAR Instruction Manual Study the instructions thoroughly before assembly. FRONT WHEEL DRIVE NEW STYLE STRUT SUSPENSION BATHTUB CHASSIS 4 BEVEL GEAR DIFFERENTIAL FULL ADJUSTABLE

More information

New Generation Rear Wheel Drive

New Generation Rear Wheel Drive New Generation Rear Wheel Drive ABC HOBBY ORIGINAL RADIO CONTROL CAR Instruction Manual Study the instructions thoroughly before assembly. REAR 2 WHEEL DRIVE REAR MOUNTED MOTOR BELT DRIVE DOUBLE DECK CHASSIS

More information

ON ROAD SETUP GUIDE PART ONE

ON ROAD SETUP GUIDE PART ONE PART ONE Ride height is adjusted by the preload of the spring collars. Winding them down will raise the ride height, while winding them up will decrease the ride height. It is important to note that adjusting

More information

.050 Allen key 1.5mm Allen key 1/16 Allen key 5/64 Allen key 3/32 Allen key Turnbuckle & 3/16 wrench

.050 Allen key 1.5mm Allen key 1/16 Allen key 5/64 Allen key 3/32 Allen key Turnbuckle & 3/16 wrench 1 Thank you for purchasing the Outlaw 4 Sprint Car! The Outlaw sprint car platform has been developed for loose dirt buggy tire racing. In this kit you will find the 4 th evolution of the car which features

More information

#0980 Intimidator 7 Direct Drive Racing Kit

#0980 Intimidator 7 Direct Drive Racing Kit #0980 Intimidator 7 Direct Drive Racing Kit 1 Thank you for purchasing the Intimidator 7! Within this kit you will find a race winning car with over 30 years of Custom Works design and quality. The latest

More information

Assembly Manual. 1/10th Formula 1 Car

Assembly Manual. 1/10th Formula 1 Car Assembly Manual 1/10th Formula 1 Car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 *Note - Sometimes it is helpful to slightly over-tighten the top clamp

More information

RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS

RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 LTO SPORT KIT FOR OVAL RACING. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ THE TEXT, LOOK AT THE PICTURES, AND THE EXPLODED

More information

DIFFERENTIAL STEERING RACK

DIFFERENTIAL STEERING RACK BAG-A DIFFERENTIAL (2 Sets) +Driver Cap Screw Diff Ball Nylon Nut Thrust Washer Thrust Ball Diff Joint Cup A Allen Wrench 850 Bearing Diff Ring Diff Spring Nylon Nut 850 Bearing Diff Ring Diff Ball Ball

More information

RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS

RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 SPORT 3.2 KIT. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ THE TEXT, LOOK AT THE PICTURES, AND THE EXPLODED VIEW

More information

3.0 Tuning Tips. To Shut Off the Engine: Use the included pipe plug or simply bump the flywheel with a wrench or plastic handled tool.

3.0 Tuning Tips. To Shut Off the Engine: Use the included pipe plug or simply bump the flywheel with a wrench or plastic handled tool. TM 8IGHT 3.0 Tuning Tips Before you start making changes on your 8IGHT 3.0 Off-Road Racing buggy, you need to make a few decisions. First of all, tires, and how they are setup, have a tremendous impact

More information

2005 to 2008 #08 Metric Nova Chassis Set Up Sheet

2005 to 2008 #08 Metric Nova Chassis Set Up Sheet Springs 1 2005 to 2008 #08 Metric Nova Chassis Set Up Sheet Flat end of spring down on tubular lower a-arms. Left Front 800lb. Right Front 750lb. Left Rear 200lb. Right Rear 225lb. On Top of Tube Axle

More information

BEFORE YOU START. XRAY USA RCAmerica, 167 Turtle Creek Boulevard Suite C Dallas, Texas 75207, USA

BEFORE YOU START. XRAY USA RCAmerica, 167 Turtle Creek Boulevard Suite C Dallas, Texas 75207, USA BEFORE YOU START The X12 is a high-quality, 1/12-pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not a toy; it is a precision

More information

ASSEMBLY AND OPERATION MANUAL

ASSEMBLY AND OPERATION MANUAL Weight: 1lb 14oz Length: 17.25" [435mm] Width: 8" [205mm] Height: 4.5" [115mm] Wheelbase: 10.5" [265mm] Motor: 20 Turn Photon Speed Radio: 2 channel surface frequency Technical Support Information For

More information

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG mm. When track High Traction or want to reduce steering

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG mm. When track High Traction or want to reduce steering NOTE : =Apply Thread lock adhesive R80059 One Way Cup () R8009 One Way R80 Pulley Set- R80004 Alu-Bulkhead-L BAG 0 CA GE =Apply CA Glue =Apply Grease R8000 Upper Arm Bracket Base R8004 One Way Plastic

More information

Make these adjustments before racing

Make these adjustments before racing FINAL ADJUSTMENTS ADJUSTING CAMBER To set the camber we recommend using our supplied #1719 camber/rear toe-in gauge. When adjusting camber you need to have the car ready to run with no body. Make these

More information

BAG F STEP F-01 STEP F-02 STEP F-03. Front and Rear Clip Installation

BAG F STEP F-01 STEP F-02 STEP F-03. Front and Rear Clip Installation q STEP F-01 BAG F Front and Rear Clip Installation The Servo Link installed in Step B-03 was set to an approximate length. The correct length will vary depending on the type of servo used, the radio settings,

More information

ASSEMBLY AND OPERATION MANUAL

ASSEMBLY AND OPERATION MANUAL Length: 9.5" [240mm] Width: 7.4" [185mm] Height: 4.7" [120mm] Ground Clearance: 1.25" [32mm] Weight: 25 oz [725g] approx. running weight with battery/motor/esc Technical Support Information For technical

More information

Installing and Squaring the Rear Axle

Installing and Squaring the Rear Axle Installing and Squaring the Rear Axle 1. Level the GF1 frame; both front to back and left to right. 2. Install the Jacob s Ladder in the frame. 3. Insert your Torsion Bars and tighten the torsion arms,

More information

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01. R Front One Way Cup (2) R Front One Way

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01. R Front One Way Cup (2) R Front One Way NOTE : =Apply Thread lock adhesive R80059 One Way Cup () R8009 One Way R80 Pulley Set- R80004 Alu-Bulkhead-L BAG 0 =Apply Glue =Apply Grease R8000 Upper Arm Bracket Base R8004 One Way Plastic Shims ()

More information

CONTENTS. All texts and images contained within this set-up book are copyright by XRAY. All rights reserved. XRAY

CONTENTS. All texts and images contained within this set-up book are copyright by XRAY. All rights reserved. XRAY CONTENTS Setting up the XRAY T3 3 Downstops 6 Ride Height 8 Droop 10 Track Width 12 Steering Throw Symmetry 13 Camber 14 Caster 16 Bump Steer 17 Ackermann 17 Toe 18 Tweak 20 Roll Center 24 Chassis Flex

More information

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01 NOTE : =Apply Thread lock adhesive R80059 One Way Cup R8009 One Way R80 Pulley Set- R80004 Alu-Bulkhead-L BAG 0 =Apply Glue =Apply Grease R8000 Upper Arm Bracket Base R8004 One Way Plastic Shims () R80005

More information

Bag 1. Bag 1. Center Pivot. Center Pivot

Bag 1. Bag 1. Center Pivot. Center Pivot 8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball

More information

BEFORE YOU START. XRAY Europe K Výstavisku 6992, Trenčín Slovakia EUROPE. XRAY USA RC America, 2030 Century Center Blvd #15 Irving, TX USA

BEFORE YOU START. XRAY Europe K Výstavisku 6992, Trenčín Slovakia EUROPE. XRAY USA RC America, 2030 Century Center Blvd #15 Irving, TX USA BEFORE YOU START The X12 is a high-quality, 1/12-pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not a toy; it is a precision

More information

1. SPECIFICATIONS 2. WHEEL ALIGNMENT

1. SPECIFICATIONS 2. WHEEL ALIGNMENT 441101 083 1. SPECIFICATIONS Front Suspension Rear Suspension Description Suspension type Spring type Shock absorber type Stabilizer bar type Suspension type Spring type Shock absorber type Stabilizer

More information

Assembly Manual. 1/10th World GT car

Assembly Manual. 1/10th World GT car Assembly Manual 1/10th World GT car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the

More information

BEFORE YOU START CUSTOMER SUPPORT

BEFORE YOU START CUSTOMER SUPPORT BEFORE YOU START The X10 is a high-quality, 1/10-pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not a toy; it is a precision

More information

... REQUIRED READING...

... REQUIRED READING... REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing the OUTLAW! Within this kit you will find a race winning car with over 21 years worth of CUSTOM WORKS design

More information

#0711 ROCKET PRO-COMP RACING KIT. Manufactured By: 760-B Crosspoint Drive Denver, NC

#0711 ROCKET PRO-COMP RACING KIT. Manufactured By: 760-B Crosspoint Drive Denver, NC #0711 ROCKET PRO-COMP RACING KIT Manufactured By: 760-B Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing

More information

GTSLOTS 2018 Sideways Lamborghini Huracan Championship Rules RELEASE NOTES: DATE/TIME ELIGIBLE DRIVERS: ELIGIBLE CARS GENERAL:

GTSLOTS 2018 Sideways Lamborghini Huracan Championship Rules RELEASE NOTES: DATE/TIME ELIGIBLE DRIVERS: ELIGIBLE CARS  GENERAL: GTSLOTS 2018 Sideways Lamborghini Huracan Championship Rules RELEASE NOTES: 10/02/18 Official Release 10/14/18 Allowed modification of Sideways GT pod; allowed use of Slot.IT anglewinder pods and Slot.IT

More information

RJS WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS

RJS WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS RJS2006 30 WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS THANKS FOR BUYING THIS RJ SPEED DRAGSTER KIT. IT IS MADE FOR STRAIGHT LINE DRAG RACING AND MAY BE BROKEN IF RUN INTO SOLID OBJECTS REPEATEDLY AT HIGH

More information

Calandra Racing Concepts

Calandra Racing Concepts Calandra Racing Concepts Carpet Knifeä Version 3 Assembly and Setup Manual Congratulations! You now own the best 1/12th scale car on the market today, the Carpet Knifeä Version 3. This completely new car

More information

TP02C. 1:10 Scale Radio Controlled Electric Powered 2WD Racing Buggy. Dimensions. Length 410mm Width 250mm Height 150mm

TP02C. 1:10 Scale Radio Controlled Electric Powered 2WD Racing Buggy. Dimensions. Length 410mm Width 250mm Height 150mm TP02C 1:10 Scale Radio Controlled Electric Powered 2WD Racing Buggy Dimensions Length 410mm Width 250mm Height 150mm Transmitter Preparation Power Switch Antenna 27MHzTransmitter Crystal T 27MHz ON Extend

More information

Next, set the bar level and tighten it down. Do this on both the driver and passenger sides.

Next, set the bar level and tighten it down. Do this on both the driver and passenger sides. Next, set the bar level and tighten it down. Do this on both the driver and passenger sides. Using two tape measures, measure the outside width at the front and the rear of the tubes. The front dimension

More information

2. Remove front wheels.

2. Remove front wheels. Read all instructions before beginning work. Following instructions in the proper sequence will ensure the best and easiest installation. Thank you for purchasing Maximum Motorsports Caster/Camber Plates.

More information

Leaf Springs Technical Information

Leaf Springs Technical Information Leaf Springs Technical Information Leaf springs are the oldest form of suspension in racing. Although they are the oldest, they seem to be the least understood. Leaf springs possess many desirable suspension

More information

E Thank you for purchasing VBC Racing product. COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT INSTRUCTIONS MANUAL

E Thank you for purchasing VBC Racing product. COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT INSTRUCTIONS MANUAL COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT 1/10 SCALE ELECTRIC COMPETITION FORMULA CAR KIT INSTRUCTIONS MANUAL E Thank you for purchasing VBC Racing product. Things that we

More information

... REQUIRED READING...

... REQUIRED READING... REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing the OUTLAW! Within this kit you will find a race winning car with over 21 years worth of CUSTOM WORKS design

More information

Chapter. Steering System Technology

Chapter. Steering System Technology Chapter 78 Steering System Technology Objectives After studying this chapter, you will be able to: Explain the operating principles of steering systems. Identify the major parts of a steering system. Compare

More information

First, check and record the camber and caster readings, they will be adjusted later.

First, check and record the camber and caster readings, they will be adjusted later. First, check and record the camber and caster readings, they will be adjusted later. The caliper-mounting bosses are machined perpendicular to the spindle so they are an excellent place for the level.

More information

Street-Lynx By. Reilly MotorSports, Inc. Installation Manual

Street-Lynx By. Reilly MotorSports, Inc. Installation Manual Street-Lynx By Reilly MotorSports, Inc. Installation Manual 1 1- Begin by removing your original rear suspension disconnect your brake lines, E-brake cables, and remove the driveshaft. To prevent fire

More information

KSKT RACING PRODUCTS

KSKT RACING PRODUCTS KSKT RACING PRODUCTS ''KSK-B'' SPEC RACING CHASSIS ASSEMBLY INSTRUCTIONS 'The Leader in SK Racing' 1 CHASSIS KIT FEATURES Black Carbon Fiber Chassis Components 2.5 mm Thick Main Chassis Battery mounting

More information

ASSOCIATED 1:10 SCALE ELECTRIC BUGGY INSTRUCTION MANUAL FOR THE TEAM ASSOCIATED RC10B Associated Electrics, Inc. RS-1

ASSOCIATED 1:10 SCALE ELECTRIC BUGGY INSTRUCTION MANUAL FOR THE TEAM ASSOCIATED RC10B Associated Electrics, Inc. RS-1 ASSOCIATED 1:10 SCALE ELECTRIC BUGGY INSTRUCTION MANUAL FOR THE TEAM ASSOCIATED RC10B4 TT RS-1 2003-2006 Associated Electrics, Inc. FINAL ADJUSTMENTS RADIO ADJUSTMENTS Use the following

More information

1. SPECIFICATIONS 2. WHEEL ALIGNMENT Front Suspension. (gas type) Rear Suspension. (gas type)

1. SPECIFICATIONS 2. WHEEL ALIGNMENT Front Suspension. (gas type) Rear Suspension. (gas type) 441101 053 1. SPECIFICATIONS Front Suspension Rear Suspension Description Suspension type Spring type Shock absorber type Stabilizer bar type Suspension type Spring type Shock absorber type Stabilizer

More information

2103 NITRO RAIL DRAGSTER KIT

2103 NITRO RAIL DRAGSTER KIT 203 NITRO RAIL DRAGSTER KIT THANKS FOR BUYING RJ SPEED S NITRO DRAG KIT. IT IS A LITEWEIGHT CAR MADE FOR STRAIGHT LINE DRAG RACING AND CAN BE BROKEN IF RUN INTO SOLID OBJECTS AT HIGH SPEED. YOU WILL NEED

More information

97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT

97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT 921663U00 97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT Thank you for choosing Rough Country for your suspension needs. This kit is an upgrade kit only. This kit includes frame mounting points and adjustable long

More information

OTK CHASSIS- SET UP GUIDE

OTK CHASSIS- SET UP GUIDE OTK CHASSIS- SET UP GUIDE Introduction This setup guide is created to facilitate a user of OTK equipment to reach an optimal chassis setup and on-track performance. The different tuning possibilities and

More information

Chapter. Suspension System Technology. Basic Suspension System. Functions of a Suspension System

Chapter. Suspension System Technology. Basic Suspension System. Functions of a Suspension System 76 Chapter Suspension System Technology Name Instructor Date Score Objective: After studying this chapter, you will be able to explain the construction and operation of modern suspension systems. Basic

More information

#0710 ELECTRIC ROCKET KIT

#0710 ELECTRIC ROCKET KIT #0710 ELECTRIC ROCKET KIT Manufactured By: 760-B Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing the

More information

RC Cheat Sheets. Set Up Your Radio-Control Car to Win! Page 1

RC Cheat Sheets. Set Up Your Radio-Control Car to Win! Page 1 RC Cheat Sheets Set Up Your Radio-Control Car to Win! Page 1 Index GENERAL Page No: Ackermann 5 Anti-dive (on road) 6 Anti-roll Bars, Sway Bars 7 Anti-squat, off road 8 Anti-squat, on road 9 Axle Height,

More information

US Patent You will find many features that set our Caster/Camber Plates apart from the rest.

US Patent You will find many features that set our Caster/Camber Plates apart from the rest. 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com US Patent 6485223 Read all instructions before beginning work. Following instructions

More information

HEIDTS RF-110. INSTALLATION INSTRUCTIONS Fairlane Comet Rear 4-Link

HEIDTS RF-110. INSTALLATION INSTRUCTIONS Fairlane Comet Rear 4-Link HEIDTS RF-110 INSTALLATION INSTRUCTIONS 66-67 Fairlane 66-67 Comet Rear 4-Link Please read these instructions completely before starting your installation. Remember the basic rule for a successful installation:

More information

MM Caster/Camber Plates, (MMCC7989)

MM Caster/Camber Plates, (MMCC7989) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Caster/Camber Plates, 1979-89 (MMCC7989) IMPORTANT: The bearing used in our

More information

along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet.

along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet. Use this XT2 Dirt Conversion Supplementary Sheet along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet. Parts included in Bag 8: 303141 SHIM 3x5x1.0MM (10) 322111 XT2 COMPOSITE

More information

Modern Auto Tech Study Guide Chapter 67 & 69 Pages Suspension & Steering 32 Points. Automotive Service

Modern Auto Tech Study Guide Chapter 67 & 69 Pages Suspension & Steering 32 Points. Automotive Service Modern Auto Tech Study Guide Chapter 67 & 69 Pages 1280 1346 Suspension & Steering 32 Points Automotive Service 1. The system allows a vehicle s tires & wheels to move up and down as they roll. Steering

More information

#4016 KIT TOOLS SUPPLIED

#4016 KIT TOOLS SUPPLIED #4016 4 =? A F H L A, O = E? 5 J H K J BH JIKIFA IE.=?J HO6A= + = H > B E > A H > K A = K E K I? H A M + I F I E J A + D = I I E = @ > = A @ I 9 E @ A > = J J A H O I JI.=?J HO6A= > K A J E J = E K JK

More information

Team Associated RC10B4 Tuning Guide

Team Associated RC10B4 Tuning Guide Team Associated RC10B4 Tuning Guide This document is a compilation of released pages from Associated Electric made for PetitRC, all credits must go to Associated Electric. Complete Tuning Guide: B4 Front

More information

MM Heavy Duty Torque-arm (MMTA-3 & -4) Engine Torque Table 4.56: : :

MM Heavy Duty Torque-arm (MMTA-3 & -4) Engine Torque Table 4.56: : : 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Orders Only: 800/839-0928 Fax: 805/544-8645 The ultimate rear suspension for your Mustang is now available from Maximum Motorsports.

More information

Section I FRONT WHEEL SUSPENSION

Section I FRONT WHEEL SUSPENSION Section I FRONT WHEEL SUSPENSION SERVICE BULLETIN REFERENCE NUMBER DATE SUBJECT CHANGES 8 FRONT WHEEL SUSPENSION CHRYSLER SERVICE MANUAL FRONT WHEEL SUSPENSION DATA AND SPECIFICATIONS C-67, C-68 C-69,

More information

Before beginning this installation read the instruction sheet thoroughly. Check that all parts on parts list are present.

Before beginning this installation read the instruction sheet thoroughly. Check that all parts on parts list are present. INSTALLATION INSTRUCTIONS C2085 SLIDE-A-LINK, FORD F-150/LIGHTNING The Slide-A-Link by Competition Engineering is designed for use in 2 Wheel Drive Ford Lightning Pickups. The rigid front mount assembly

More information

INSTRUCTIONS MANUAL COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT 1/10 SCALE ELECTRIC COMPETITION CAR KIT

INSTRUCTIONS MANUAL COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT 1/10 SCALE ELECTRIC COMPETITION CAR KIT COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT 1/10 SCALE ELECTRIC COMPETITION CAR KIT INSTRUCTIONS MANUAL E Thank you for purchasing VBC Racing product. Things that we should

More information

Z-CAR ZMXT-8 RTR RTR NITRO OFF-ROAD

Z-CAR ZMXT-8 RTR RTR NITRO OFF-ROAD TEST DRIVE EXCLUSIVE! Z-CAR ZMXT-8 RTR RTR NITRO OFF-ROAD THIS TRUGGY BREAKS THE MOLD WORDS KEVIN HETMANSKI kevinh@airage.com PHOTOS JOSEPH ARTHUR Z-CAR, A DIVISION OF SH ENGINES, is distributed exclusively

More information

DODGE 3 SUSPENSION LIFT KIT

DODGE 3 SUSPENSION LIFT KIT 921351200 Kit Contents: 9280:Front Coil Springs 1351BOX1: Upper Control Arms Lower Control Arms Sway bar Brackets Brake Proportioning Valve Bracket Track Bar Relocation Bracket 1351BOX2: 5.75 Blocks U-bolt

More information

Steering and Suspension

Steering and Suspension The Steering and Suspension system is engineered to allow the vehicle to turn and absorb road irregularities. The suspension is comprised of springs, suspension arms or links and shock dampers. These components

More information

R R11 Eccentric Hub-Alu (4) R R11 Eccentric Hub-Alu (4) NOTICE. Pulley cover direction NOTICE BAG 01 NOTICE BAG 01

R R11 Eccentric Hub-Alu (4) R R11 Eccentric Hub-Alu (4) NOTICE. Pulley cover direction NOTICE BAG 01 NOTICE BAG 01 BAG BAG R Spool Axle Alu RA Front Spool Pulley Set 8T (4pcs) R Diff Gears (with Axle) Trim any excess flashing from the diff gear axle at the mold injection point. (pcs) (4pcs) R Spool Outdrive (pcs) R6

More information

2013-UP 3500 Dodge 5 Lift Kit SRW

2013-UP 3500 Dodge 5 Lift Kit SRW 92369200 2013-UP 3500 Dodge 5 Lift Kit SRW Thank you for choosing Rough Country Suspension for your Off Road needs. Rough Country recommends a certified technician installs this system. In addition to

More information

97-06 JEEP TJ 3 1/4 PROGRESSIVE COIL/SPACER KIT

97-06 JEEP TJ 3 1/4 PROGRESSIVE COIL/SPACER KIT 92PERF1641 97-06 JEEP TJ 3 1/4 PROGRESSIVE COIL/SPACER KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition

More information

OWNER'S MANUAL Magnolia Ave., Chino, CA phone: (909) fax: (909)

OWNER'S MANUAL Magnolia Ave., Chino, CA phone: (909) fax: (909) OWNER'S MANUAL Carefully read through all instructions to familiarize yourself with the parts, construction techniques, and tuning tips outlined in this manual. Being able to grasp the overall design of

More information

REAR AXLE AND SUSPENSION RA 1

REAR AXLE AND SUSPENSION RA 1 REAR AXLE AND SUSPENSION RA1 RA2 REAR AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated Replace tires or inflate to

More information

SECTION steering mechanism

SECTION steering mechanism 07-302.01/ 1 2011MR17 SECTION 07-302.01 GENERAL Description See Figure 1. The includes the steering wheel (1), the steering column, the miter box (3), the steering shafts (2 and 4), and the drag link (7).

More information

Bag 1. Bag 1. Center Pivot. 3 Center Pivot Cap. Center Pivot

Bag 1. Bag 1. Center Pivot. 3 Center Pivot Cap. Center Pivot Battle Axe 2.0 1:10th Oval Weapon from Team CRC Assembly Manual 0 2. e Ax s tle Win s! t rd Ba s + bi C. ow CR T.Q Sn 0 20 servo and saver not included Part # 100 Calandra Racing Concepts 6785 Martin Street

More information

iracing.com Williams-Toyota FW31 Quick Car Setup Guide

iracing.com Williams-Toyota FW31 Quick Car Setup Guide iracing.com Williams-Toyota FW31 Quick Car Setup Guide In this guide we will briefly explain a number of key setup parameters which are distinct to the FW31 and which are new to iracing vehicles. We hope

More information

DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I

DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment

More information

Quarter Midget Catalog

Quarter Midget Catalog Quarter Midget Catalog 317.271.7100 1698 Midwest Blvd, Indianapolis, IN 46214 www.advancedracing.net 5500 SERIES QUARTER MIDGET SHOCK The Advanced Racing Suspensions quarter midget shock continues to be

More information

The DINO files: Ford GT40 set-up

The DINO files: Ford GT40 set-up The DINO files: Ford GT40 set-up Start removing the body and take a look to the motor mount. Using the axle with has a reduced section in the middle, we'll improve clearance between axle and motor can,

More information

INSTRUCTIONS MANUAL COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT 1/12 SCALE ELECTRIC COMPETITION CAR KIT

INSTRUCTIONS MANUAL COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT 1/12 SCALE ELECTRIC COMPETITION CAR KIT COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT 1/12 SCALE ELECTRIC COMPETITION CAR KIT INSTRUCTIONS MANUAL E Thank you for purchasing VBC Racing product. Things that we should

More information

TOYOTA 4-RUNNER KIT 5 KIT

TOYOTA 4-RUNNER KIT 5 KIT 92173600 1990-1995 TOYOTA 4-RUNNER KIT 5 KIT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these

More information

COMPETITION ENGINEERING. 80 Carter Drive P.O. Box 1470 Guilford, CT Phone: (203) Fax: (203)

COMPETITION ENGINEERING. 80 Carter Drive P.O. Box 1470 Guilford, CT Phone: (203) Fax: (203) INSTALLATION INSTRUCTIONS P/N: C2094 SLIDE-A-LINK The Slide-A-Link by Competition Engineering is designed for use in Stock Eliminator and Bracket Racing vehicles. The rigid front mount assembly clamps

More information

Mounting Overlap Shield. Face Clamps. Gap. Seat Depth. Lead In Chamfer. Loose Fit.

Mounting Overlap Shield. Face Clamps. Gap. Seat Depth. Lead In Chamfer. Loose Fit. Mounting Introduction: Reali-Slim thin section ball bearings have a crosssection thickness that is much thinner than standard bearings of the same diameter, and are therefore more sensitive to shaft and

More information

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS XJ SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 7 page REAR SUSPENSION... 16 ALIGNMENT TABLE OF CONTENTS page AND WHEEL ALIGNMENT...1 DIAGNOSIS AND TESTING SUSPENSION

More information

SUSPENSION 2-1 SUSPENSION CONTENTS

SUSPENSION 2-1 SUSPENSION CONTENTS ZJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 14 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION

More information

VariShock QuickSet 2 Coil-Over Installation and Tuning Guide

VariShock QuickSet 2 Coil-Over Installation and Tuning Guide VariShock QuickSet 2 Coil-Over Installation and Tuning Guide Part Number Qty. Description Various 2 Coil-Over Shock with Threaded Body (pair) 899-002-200 2 Lower Coil-Over Spring Seat 899-002-201 2 Upper

More information

Manufactured By: #0723 OUTLAW 3-SHOT RACING KIT. 760 Crosspoint Drive Denver, NC

Manufactured By: #0723 OUTLAW 3-SHOT RACING KIT. 760 Crosspoint Drive Denver, NC Manufactured By: #0723 OUTLAW 3-SHOT RACING KIT 760 Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING...UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing the OUTLAW

More information

The following items are needed to install your Speed Kit. Phillips head screw driver 3/16" nut driver 1.5mm hex wrench

The following items are needed to install your Speed Kit. Phillips head screw driver 3/16 nut driver 1.5mm hex wrench BRUSHLESS SPEED KIT INSTALLATION INSTRUCTIONS REQUIRED TOOLS The following items are needed to install your Speed Kit. Phillips head screw driver 3/16" nut driver 1.5mm hex wrench 1. REMOVE STEERING LINKAGE

More information

1:12 SCALE ON ROAD CAR KIT

1:12 SCALE ON ROAD CAR KIT 2 SCALE ON ROAD CAR KIT INSTRUCTION MANUAL OR KIT #4015 SAVE VE THIS MANUAL! Use with current catalog for future, hassle-free re-ordering of parts. 1998 Associated Electrics, Inc. - 9? D = I I EI @ A I

More information

ASSEMBLY AND OPERATION MANUAL

ASSEMBLY AND OPERATION MANUAL ASSEMBLY AND OPERATION MANUAL www.duratrax.com ITEMS INCLUDED The following items are included with your Vendetta Rally. Chassis Transmitter Body Decal Sheet Instruction Manual Exploded View/Parts Listing

More information

JEEP JK 3 1/4 COIL & SPACER KIT W/ PERFORMANCE 2.2. SHOCK ABSORBERS

JEEP JK 3 1/4 COIL & SPACER KIT W/ PERFORMANCE 2.2. SHOCK ABSORBERS 92PERF693 JEEP JK 3 1/4 COIL & SPACER KIT W/ PERFORMANCE 2.2. SHOCK ABSORBERS Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install

More information

#0715 NITRO ROCKET KIT

#0715 NITRO ROCKET KIT #0715 NITRO ROCKET KIT Manufactured By: 760-B Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing the ROCKET!

More information

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS

SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL

More information

GM 2016-UP wd 3.5 Stamped Steel & Aluminum LCA Knuckle Lift Kit

GM 2016-UP wd 3.5 Stamped Steel & Aluminum LCA Knuckle Lift Kit 921121300B *12130BAG4* 12130BAG4 GM 2016-UP 1500 4wd 3.5 Stamped Steel & Aluminum LCA Knuckle Lift Kit Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified

More information

DODGE LIFT KIT

DODGE LIFT KIT 9237100R1 Kit Contents: 9280:Front Coil Springs 1371BOX1: Upper Control Arms Lower Control Arms 1371BOX2 Sway bar Brackets Track Bar Bracket 4-U-bolts 2-4 blocks 6612: Pitman Arm 8159: Front Shock 8160:

More information

:: Additional Features Your new TC6 comes unassembled and requires the following items for completion. (refer to catalog section for suggestions):

:: Additional Features Your new TC6 comes unassembled and requires the following items for completion. (refer to catalog section for suggestions): 8/10 2 :: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10TC6. Please take a moment to

More information

Manufactured By: CustomWorks RC Products LLC 760-B Crosspoint Drive Denver, NC #0928 ENFORCER GSX2 RACING KIT

Manufactured By: CustomWorks RC Products LLC 760-B Crosspoint Drive Denver, NC #0928 ENFORCER GSX2 RACING KIT #0928 ENFORCER GSX2 RACING KIT Manufactured By: CustomWorks RC Products LLC 760-B Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and

More information

BIND ST-TRIM TH-TRIM ST-D/R

BIND ST-TRIM TH-TRIM ST-D/R 4 4 4 4 BIND ST-TRIM TH-TRIM ST-D/R 1. Put the battery in the car. 2. Install the battery. 3. Turn on the transmitter. Connect firmly. 4. Turn on the electronic speed controller. ON OFF AX80084 UV Joint

More information

Engine Does Not Start or Is Hard to Start Cause of Trouble. 1. Open the drain screw, and check Fuel not supplied (1) Fuel tank empty

Engine Does Not Start or Is Hard to Start Cause of Trouble. 1. Open the drain screw, and check Fuel not supplied (1) Fuel tank empty 20. Engine Does Not Start or Is Hard to Start 20-1 Engine Output Insufficient 20-2 Poor Performance at Low Speed and Idling 20-3 Poor Performance at High Speed 20-3 Unsatisfactory Operation 20-4 Fuel Gauge

More information

Mod 71 Nose gear leg bungee, replacement with springs

Mod 71 Nose gear leg bungee, replacement with springs Mod 71 Nose gear leg bungee, replacement with springs Classification Optional Applicability Compliance Europa Tri-gear Classic and XS Optional Introduction The steel tube of the Europa s nose gear leg

More information

#0918 INTIMIDATOR GSX2 RACING KIT. Manufactured By: 760-B Crosspoint Drive Denver, NC

#0918 INTIMIDATOR GSX2 RACING KIT. Manufactured By: 760-B Crosspoint Drive Denver, NC #0918 INTIMIDATOR GSX2 RACING KIT Manufactured By: 760-B Crosspoint Drive Denver, NC 28037 www.customworksrc.com REQUIRED READING.........UNDERSTAND THIS MANUAL! Thank You and Congratulations on purchasing

More information