t Technical Cylinder & Valve Sensors Cylinder & Cylinder & Valve Valve Sensors Contents Sensors 5.1 Cylinder & Valve Sensors

Transcription

1 Cylinder & Cylinder & Cylinder & Cylinder sensors are used to provide end-ofstroke and position detection for hydraulic and pneumatic cylinder applications. Hydraulic cylinder walls are typically made of steel. Since inductive and magnetic field sensors cant see through the steel cylinder wall to detect the piston inside, hydraulic cylinders use pressure-rated inductive sensors that can handle direct exposure to pressurized hydraulic fluid in the cylinder to provide end-ofstroke detection. A specialized inductive sensor is bolted or threaded into the cylinder end cap. The sensing face of the inductive sensor directly detects the cylinder rod or cushion as it reaches its end of travel. For n-contact, wear-free position detection of pneumatic cylinder piston position, Balluff magnetic field sensors use magneto-resistive techlogy to detect the piston magnet through the aluminum wall of the cylinder. Typically two sensors are employed to provide end-of-stroke detection in both directions, or can be placed anywhere along the length of the cylinder to detect cylinder position. Advantages of Balluff magnetic field sensors include universal compatibility with either Hall Effect or Reed Switch cylinder magnet polarizations, reduction or elimination of double switch points, higher ise immunity, and elimination of electrical contact wear and sticking. Magnetic field sensors are available in a variety of cylinder-friendly mounting configurations, as well as with special features like weld field immunity..2 Selection Guide. BMF 103 Compact.8 BMF 273 C-Slot.9 BMF 303 Miniature Slot Mount.12 BMF 30 Universal & Universal Metal.22 BMF 307 T-Slot.24 BMF 31 Drop In T-Slot.27 BMF 21 Tie-Rod.29 BMF 32 Rugged Duty.32 BMF 07M, 08M, 12M Prox Style.34 Installation Hints.3 BMF Techlogy Comparison.36 BIL Magneto-Inductive Position Sensor Power Clamp & Gripper Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

2 Selection Guide Selection Guide Series BMF 103 BMF 273 BMF 303 BMF 30K BMF 30M Compact C-Slot Miniature Slot Universal Universal Metal Cylinder Type C-Slot HW-41/42 HW-28/30/31/62 HW-32 (Norgren) HW-32 (Norgren) T-Slot HW-43/63/6/ 79/81 HW-33/40/1/ 60/66 HW-17/20/22/ 23/26/37/0/2/ 3/8/64/67/82 HW-17/20/22/ 23/26 Dove Tail HW-68/7/78 HW-44/69 HW-3/36/38/ 39/4/46/47 HW-3/36/38/ 39/4/46/47 Trapezoidal HW-80 HW-2/27 HW-2/27 Round HW-34/9/61/80 HW-24 HW-24 Tie Round HW-74 HW-21 & HW-8/ HW-21 & HW-10 HW-70/71/72/76/77 HW-21 & HW-8/ HW-21 & HW-10 HW-70/71/72/76/77 Duo Rail Flush Mount Bracketless Connection Integral Connector Pigtail Connector M and M8 M8 M and M8 M8 and M12 Prewired Cable Outputs PNP N.O. 3-Wire PNP N.C. 3-Wire NPN N.O. 3-Wire NPN N.C. 3-Wire PNP N.O. Weld Field Immune 3-Wire NPN N.O. Weld Field Immune 3-Wire PNP N.O. Reed 3-Wire AC/DC Reed 2-Wire V AC/DC Housing Plastic LCP PBT LCP LCP Metal AL Attributes Short Circuit Protection Reverse Polarity Protection Temperature Range Up to 8 C Temperature Range Up to 10 C CE UL Features Pages Optimized for shortstroke cylinders, very compact size, perpendicular mounting, interchangeable brackets. Bracketless type designed for drop in installation into C slot.8 Miniature type for flush mounting in narrow channels, interchangeable brackets.9 Universal sensor designed for most applications; wide variety of outputs, connections, mounting options; plastic housing.12 &.1 Universal sensor designed for most applications; wide variety of outputs, connections, mounting options; metal housing; weld immune extended temperature range.14.2

3 Selection Guide Cylinder & Selection Guide BMF 307 T-Slot HW-73 HW-86 BMF 31K Drop In T-Slot HW-73 BMF 31M Drop In T-Slot Metal HW-73 BMF 21 Tie-Rod HW-11 HW-8/10/10E HW-8 BMF 32 Rugged Duty HW-12/14/18 HW-73 HW-13/1/34 BMF 7M, 8M, 12M Prox Style Cylinder & M8 M8 M8 and M12 M8 M8 and M12 M12 M V AC/DC LCP PA 66 AL PBT AL CuZn Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors Bracketless type for flush installation into T-slot channels.22 Bracketless type designed for drop in replacement into T-slot channels, plastic housing.24 Bracketless type designed for drop in replacement into T-slot channels, metal housing, weld immune extended temperature range.2 Cost-effective, optimized for mounting on tie rod cylinders.27 Rugged metal housing for the most demanding applications, tie rod mounting, available in weld immune.29 Designed for long range target sensing, extremely high switching speeds, suitable for tachometer applications, available in 7, 8, and 12 mm diameters.32 7Accessories o Product Overview t Technical Reference p Part Number Index

4 Selection Guide Selection Guide Series BIL Strokemaster Power Clamp Pressure Rated Bracket Required Connection Integral Connector M8 M12, Mini M8, M12, M18 M12 Pigtail Connector M12 Cable Outputs PNP N.O V PNP N.C V NPN N.O. NPN N.C. PNP N.O. Weld Field Immune AC/DC V AC/DC V ma Housing Plastic PA Metal SS/AL SS, SS430F Attributes Overload Protection Short Circuit Protection Reverse Polarity Protection Temperature Range Up to 7 C Up to 70 C Up to 120 C Up to 70 C Pressure Range 3000 PSI Up to 720 PSI CE UL Features Non-contact position feedback, ideal for short and medium stroke length applications; 10 to 160 mm stroke length Weld field immune, pressure rated to 3000 psi, sealed directly at flange, can be oriented after installation, various lengths available Pressure rated as high as 720 psi, corrosion resistant stainless steel housing, wide variety of housing diameters and thread lengths Designed for use in power clamp and gripper applications, incorporates two sensors into one unit to detect open or closed position, weld field immune Pages

5 BMF 103 Cylinder & BMF 103 Compact Magnetic Field Series Connection Type BMF 103 To create the compact BMF 103 magnetic field sensor, Balluff engineers employed GMR (giant magnetoresistive) techlogy to shrink the length of the sensor housing. The perpendicular cable exit and extremely short sensing face allow two BMF 103's to be placed as close together as mm in a single channel. The BMF 103 is the perfect solution for cramped spaces and today s short-stroke, compact pneumatic cylinders and actuators. PNP NPN Normally-open Normally-closed Normally-open BMF 103 Cable + M0 Pico Connector (S26) BMF 103K-PS-C-2A-S26-** BMF 103 Cable + M08 DC Na Connector (S49) Rotating Threaded Connector BMF 103K-PS-C-2A-SA2-S49-** BMF 103K-PO-C-2A-SA2-S49-** BMF 103K-NS-C-2A-SA2-S49-** BMF 103 PuFlex Cable BMF 103K-PS-C-2A-PU-* BMF 103K-PO-C-2A-PU-* BMF 103K-NS-C-2A-PU-* Cylinder & Rated operating field strength H nl Assured operating field strength I H a I Hysteresis of I H n I Temperature drift of turn-on point of I H n I Turn-on delay Turn-off delay Supply voltage U B Voltage drop U d Rated insulation voltage Ui Rated operating current I e No-load supply current I 0 max. Off-state current Ir Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range T a LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approval Recommended * Please specify the cable length for sensor. Standard lengths are as follows: 03 = 3 m, 0 = m. Consult the factory for other cable length options. **Please specify length for the pigtail. Standard lengths are as follows: 00.2 = 0.2 m, 00. = 0. m. Consult the factory for other cable length options. 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 0.07 ms 0.07 ms 2. V 100 ma ma C LCP M pigtail BKS-B 2-3-PU ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 0.07 ms 0.07 ms 2. V 100 ma ma C LCP M8 pigtail C49 ANE-00-VY-00M 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 0.07 ms 0.07 ms 2. V 100 ma ma C LCP cable, PUR 3 30 AWG Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors Wiring diagrams PNP/Cable PNP/Connector NPN/Cable Output current temperature curves 7Accessories o Product Overview t Technical Reference p Part Number Index

6 BMF 103 Brackets BMF 103 Typical Ordering Code BMF 103-HW-41 Advantages Cylinder channel C-slot bracket e.g. SMC, Bimba Internal Set Screw BMF 103-HW-42 C-slot Festo Slot-10 Advantages BMF 103-HW-43 Internal Set Screw T-slot Adjust switchpoint in seconds! Turn screw one revolution, adjust position, tighten. Switchpoint can't be lost. Even if you replace the sensor, the adjusted switchpoint is retained by the mounting bracket. BMF 103-HW-63 e.g. Festo Slot-8, Bosch, SMC External Set Screw T-slot Can be inserted into slot from above. e.g. Bimba Flat 1 To order a combo kit of sensor with mounting bracket, include the bracket code in the part number. Example : BMF 103K/HW41- PS-C-2-PU-03 BMF 103-HW-6 BMF 103-HW-68 T-slot e.g. Parker P1M Dovetail e.g. Fabco Pancake.6

7 BMF 103 Cylinder & BMF 103 Brackets Ordering Code BMF 103-HW-74 BMF 103-HW-7 Advantages Cylinder channel Tie Rod e.g. PHD Dove Tail bracket M2x0.4-6H M3X0.-6H M3X0.-6H M2x0.4-6H 3.20 Ø10 Ø º.30 60º 6.70 Cylinder & e.g. Numatics BMF 103-HW-78 Dove Tail 60 BMF 103-HW-79 BMF 103-HW Rexroth PSK Rail Rexroth CKK Rail e.g. Norgren Small Bore M3X0.-6H Ø9.3 Ø8.6 60º Ø6.9 M2x0.4-6H M3X0.-6H M2x0.4-6H M3X0.-6H M2x0.4-6H Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

8 BMF 273 for C-slot BMF 273 BMF 273 The compact sensor for pneumatic cylinders with C-slot Series Connection Type BMF 273 Cable and M08 DC na (S49) BMF 273 PuFlex Cable The C-slot is becoming increasingly common in pneumatic cylinders and grippers. Installation from above into the slot is a requirement for fast and simple installation. The BMF 273 meets all these requirements while also offering reliable switching characteristics. Features Can be installed from above into the C-slot Disappears into the slot Proven electronics from the BMF line: Low hysteresis, precise switching point Rugged, compact low profile housing Hold-down screw protected from over-tightening, uses standard screw driver Cable clip for ease of cable routing and securing Install without a mounting bracket, for cylinders with C-slot, e.g. Festo (Slot 10), SMC, Parker and Sommer Automatik Wiring diagrams N.O. PNP/cable PNP/ NPN/ N.C. NPN/cable PNP/ PNP NPN Normally-open Normally-closed Normally-open Normally-closed Rated switching field strength I H n I Assured switching field strength I H a I Hysteresis of I H n I Temperature drift of turn-on point of I H n I Turn-on delay Turn-off delay Supply voltage U S Voltage drop Ud Rated insulation voltage U i Rated operational current I e No-load supply current I0 max. Polarity reversal protected Short circuit protected Ambient temperature range Ta LED Protection per IEC 6029 Housing material Connection type No. of wires gauge Approval Recommended * Please specify the cable length for sensor. Standard lengths are as follows: 03 = 3 m, 0 = m. Consult the factory for other cable length options. **Please specify length for the pigtail. Standard lengths are as follows: 00.2 = 0.2 m, 00. = 0. m. Consult the factory for other cable length options. BMF 273K-PS-C-2A-SA2-S49-** BMF 273K-PO-C-2A-SA2-S49-** BMF 273K-NS-C-2A-SA2-S49-** BMF 273K-NO-C-2A-SA2-S49-** 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 0.07 ms 0.07 ms 2. V 100 ma 8 ma C PBT M8 pigtail C49 ANE-00-VY-00M BMF 273K-PS-C-2A-PU-* BMF 273K-NS-C-2A-PU-* 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 0.07 ms 0.07 ms 2. V 100 ma 8 ma C PBT Cable, PUR 3 26 AWG Output current temperature curves NPN/.8

9 BMF 303 Cylinder & BMF 303 Minature Slot Mount Series Connection Type BMF 303 The BMF 303 is flush mounted in the cylinder slot. So small it disappears completely. Nothing to stick out thing in the way! Features - Non-contact, wear-free position sensing - Can be installed on any standard cylinder using specific mounting brackets - No "double switch points" - Insensitive to contamination PNP NPN Normally-open Normally-closed Normally-open Normally-closed BMF 303 Cable + M0 Pico Connector (S26) BMF 303K-PS-C-2A-S26-** BMF 303K-NS-C-2A-S26-** BMF 303 Cable + M08 DC Na Connector (S49) Rotating Threaded Connector BMF 303K-PS-C-2A-SA 2-S49-** BMF 303K-PO-C-2A-SA 2-S49-** BMF 303K-NS-C-2A-SA 2-S49-** BMF 303K-NO-C-2A-SA 2-S49-** BMF 303 PuFlex Cable BMF 303K-PS-C-2A-PU-* BMF 303K-PO-C-2A-PU-* BMF 303K-NS-C-2A-PU-* BMF 303K-NO-C-2A-PU-* Cylinder & Rated operating field strength H nl Assured operating field strength I H a I Hysteresis of I H n I Temperature drift of turn-on point of I H n I Turn-on delay Turn-off delay Supply voltage U B Voltage drop Ud Rated insulation voltage U i Rated operating current I e No-load supply current I0 max. Off-state current I r Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range T a LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approval Recommended * Please specify the cable length for sensor. Standard lengths are as follows: 03 = 3 m, 0 = m. Consult the factory for other cable length options. **Please specify length for the pigtail. Standard lengths are as follows: 00.2 = 0.2 m, 00. = 0. m. Consult the factory for other cable length options. 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 0.07 ms 0.07 ms 2 V 100 ma ma C LCP M pigtail BKS-B 2-3-PU-0 Wiring diagrams PNP/Cable 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 0.07 ms 0.07 ms 2 V 100 ma ma C LCP M8 pigtail C49 ANE-00-VY-00M PNP/Connector 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 0.07 ms 0.07 ms 2 V 100 ma ma C LCP cable, PUR 3 30 AWG Output current temperature curves Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview Typical NPN/Cable NPN/Connector t Technical Reference p Part Number Index

10 BMF 303 Brackets BMF 303 Advantages Sensor disappears in the slot! Ordering Code BMF 303-HW-28 Advantages Cylinder channel bracket C-slot Can be inserted into slot from above. Adjust switchpoint in seconds! Turn screw one revolution, adjust position, tighten. BMF 303-HW-30 e.g. SMC C-slot Festo Nut-10 Switchpoint can't be lost. Even if you replace the sensor, the adjusted switchpoint is retained by the mounting bracket. BMF 303-HW-31 C-Nut Other bracket solutions are available. Contact factory for details. To order a combination kit of sensor with mounting bracket, include the bracket code in the part number. Example: BMF 303K/HW30-PS-C-2-PU-03 BMF 303-HW-33 e.g.festo T-slot Installation of BMF 303-HW-60 BMF 303-HW-34 e.g. Festo Nut-8, Bosch, SMC Round Cylinders Ø < mm M Ø2.8 Tube cuffs for BMF 303-HW-9/61 SCHLAUCHSCHELLE BMF GR. Pneumatic Tube Cuff Sizes Tube Cuff Piston Ø Cylinder Ø Size 0 < BMF 303-HW-40 BMF 303-HW-40 BMF 303-HW-44 T-slot e.g. Festo Nut-8, Bosch, SMC Dovetail 60 /90 e.g. Festo, Bosch, Numatics, Hoerbiger-Origa, Norgren-Martonair.10

11 BMF 303 Cylinder & BMF 303 Brackets Ordering Code BMF 303-HW-1 BMF 303-HW-60 BMF 303-HW-9 BMF 303-HW-61 BMF 303-HW-62 Advantages Cylinder channel bracket T-slot A T-Slot B Round Cylinders Ø mm HW9 HW1 HW61 HW60 Cylinder & Selection Guide BMF 303-HW-66 T-slot e.g. Parker P1M M2x0.4-6H.90 Ø2.8 Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive BMF 303-HW-69 Dovetail M2x0.4-6H Cylinder Position º Ø2.8 Power Clamp & Gripper 6Connectors e.g. Fabco Pancake BMF 303-HW-80 7Accessories o Product Overview t Technical Reference e.g. Bosch p Part Number Index

12 BMF 30 BMF 30 BMF 30 With its versatile mounting system, the BMF 30 is the most flexible magnetic field sensor available. A wide selection of interchangeable brackets allows the BMF 30 to fit virtually any cylinder type. Series Connection Type BMF 30 Cable + M08 DC Na Connector (S49) Rotating Threaded Connector Features Interchangeable bracket system Non-contact and wearfree sensing of piston location Insensitive to contamination Detects piston position through the cylinder wall Can be attached to any standard cylinder size using available mounting brackets Eliminates multiple switchpoints Brackets for all common cylinder types Pre-wired cable or quick disconnect Weld-immune version available PNP NPN Normally-open Normally-closed Normally-open Normally-closed Rated operating field strength H nl Assured operating field strength I Ha I Hysteresis of I H n I Temperature drift of turn-on point of I H n I Turn-on delay Turn-off delay Supply voltage U B Voltage drop U d Rated insulation voltage U i Rated operating current I e No-load supply current I 0 max. Off-state current I r Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range T a LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approval Recommended BMF 30K-PS-C-2-SA2-S49-** BMF 30K-PO-C-2-SA2-S49-** BMF 30K-NS-C-2-SA2-S49-** BMF 30K-NO-C-2-SA2-S49-** 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 30 ma C LCP M8 pigtail C49 ANE-00-VY-00M * Please specify the cable length for sensor. Standard lengths are as follows: 03 = 3 m, 0 = m. Consult the factory for other cable length options. **Please specify length for the pigtail. Standard lengths are as follows: 00.2 = 0.2 m, 00. = 0. m. Consult the factory for other cable length options. To order a set (sensor and mounting bracket): Please include the bracket code in the part number e. g. BMF 30K/HW20-PS-C-2-PU-0.12

13 BMF 30 Cylinder & BMF 30 Universal Sensor BMF 30 Cable + M12 DC Micro Connector (S4) BMF 30K-PS-C-2-S4-** BMF 30 PuFlex Cable BMF 30K-PS-C-2-PU-* BMF 30K-PO-C-2-PU-* BMF 30K-NS-C-2-PU-* BMF 30K-NO-C-2-PU-* BMF 30 Cable + M12 DC Micro Connector (S4) Weldfield Immune BMF 30K-PS-W-2-SA3-S Wiring diagrams Normally-open PNP/Cable PNP/Connector NPN/Cable NPN/Connector Normally-closed PNP/Cable Cylinder & 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 30 ma C LCP M12 pigtail C04 AEL-00-VY-00M 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 30 ma C LCP cable, PUR 3 26 AWG 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 4 V 20 ma C LCP M12 pigtail C04 AEL-00-VY-00M PNP/Connector NPN/Cable NPN/Connector Output current temperature curves Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

14 BMF 30 BMF 30 Series Connection Type BMF 30 M12 DC Micro Connector (S4) BMF 30 M08 DC Na Connector (S49) BMF 30 M08 DC Na Connector (S49) BMF 30 M12 DC Micro Connector (S4) Welding applications are problem for the BMF 30M/ series magnetic field sensors. Developed with a heavy-duty weld slag resistant metal housing and a specially tuned output circuit (immunity for weld currents up to 2kA), these sensors perform in even the toughest environments. Extended Temperature Weldfield Immune PNP Normally-open BMF 30M-PS-C-2-S4 BMF 30M-PS-C-2-S49 BMF 30M-PS-C-2-SA4-S49 BMF 30M-PS-W-2-S4 Rated operating field strength H nl Assured operating field strength I H a I Hysteresis of I H n I Temperature drift of turn-on point of I H n Turn-on delay Turn-off delay Supply voltage U B Voltage drop U d Rated insulation voltage U i Rated operating current I e No-load supply current I 0 max. Off-state current I r Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range T a LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approval Recommended 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 30 ma C Al C04 AEL-00-VY-00M 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 30 ma C Al C49 ANE-00-VY-00M 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 3 %/ C 3.1 V 30 ma C IP 6 Al C49 ANE-00-VY-00M 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 4 V 30 ma C Al C04 AEL-00-VY-00M Wiring diagrams PNP/Cable NPN/Cable Output current temperature curves PNP/Connector NPN/Connector.14

15 BMF 30 Cylinder & BMF 30 Reed Switch Series Connection Type BMF 30 Reed Switch The ecomical BMF 30K-R reed switch has an LED for function display and as a setup aid. The recovery diode for switching an inductive load is already integrated. Features Fast and easy to install Fits any standard cylinder size using available brackets No loss of the setpoint when replacing a switch DC AC/DC PNP, Normally-open Normally-open BMF 30 Cable + M08 DC Na Connector (S49) BMF 30K-R-PS-F-3-S49-** BMF 30 PuFlex Cable BMF 30K-R-PS-F-3-* BMF 30 PuFlex Cable BMF 30K-R-US-L-3-* Cylinder & Turn-on delay Turn-off delay Supply voltage U B Reed contact rating max. Rated operating current I e Minimum operating current Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range Ta LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approval Recommended * Please specify the cable length for sensor. Standard lengths are as follows: 03 = 3 m, 0 = m. Consult the factory for other cable length options. **Please specify length for the pigtail. Standard lengths are as follows: 00.2 = 0.2 m, 00. = 0. m. Consult the factory for other cable length options. To order a combination kit of sensor with mounting bracket, include the bracket code in the part number. Example: BMF 30K/HW20-PS-C-2-PU ms 0.2 ms 10 W 00 ma 0. µf C IP 6 LCP M8 pigtail C49 ANE-00-VY-00M 0.7 ms 0.2 ms 10 W 00 ma 0. µf C IP 6 LCP cable, PVC 3 26 AWG 0.7 ms 0.2 ms Vac/Vdc 10 W 128 ma at 24 Vac/Vdc 86 ma at 11 Vac/Vdc 43 ma at 230 Vac/Vdc 3 ma C IP 6 PA cable, PVC 2 26 AWG Note: Reed switch is configured for PNP operation with respect to operation of the function LED. The reed switch itself is inherently bi-directional for current. This applies to DC versions only. Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview Wiring Diagrams DC/Cable DC/Connector AC/DC/Cable t Technical Reference p Part Number Index

16 Installation Benefits BMF 30 Brackets BMF 30 Ordering Code BMF 30-HW-17 Advantages Cylinder Channel T-slot Bracket Can be inserted into slot from above. e.g. Festo, SMC BMF 30-HW-20 T-slot Switchpoint is set in seconds! Turn screw one revolution, adjust position, tighten. Switchpoint can't be lost. Even if you replace the sensor, the same switchpoint remains because the bracket doesn't move. without Set screw with Set screw BMF 30-HW-21 together with BMF 21-HW-8 BMF 30-HW-21 together with BMF 21-HW-10 BMF 30-HW-22 T-slot Tube Cuffs for BMF 30-HW-24: SCHLAUCHSCHELLE BMF GR. BMF 30-HW-23 T-slot Pneumatic Tube Cuff Sizes Tube Cuff Piston Ø Cylinder Ø Size 0 < BMF 30-HW-24 BMF 30-HW-2 without slot round cylinder with piston diameter < mm trapezoidal slot.16

17 BMF 30 Ordering Code BMF 30-HW-26 BMF 30-HW-27 Advantages Cylinder Channel T-slot A T-slot B Trapezoidal guide Cylinder & Bracket Position for T-slot A Position for T-slot B BMF 30 Brackets Cylinder & e.g. Bosch BMF 30-HW-32 C-slot Selection Guide BMF 30-HW-3 e.g. Norgren Dovetail slot Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive BMF 30-HW-36 e.g. Tol-o-matic Dovetail slot Cylinder Position 6.6 Power Clamp & Gripper Connectors e.g. Numatics 7Accessories BMF 30-HW-37 T-slot o Product Overview 12.7 t Technical Reference p Part Number Index e.g. Parker, SST, ER

18 Installation Benefits Can be inserted into slot from above. Switchpoint is set in seconds! Turn screw one revolution, adjust position, tighten. Switchpoint can't be lost. Even if you replace the sensor, the same switchpoint remains because the bracket doesn't move. BMF 30 Brackets BMF 30 Ordering Code BMF 30-HW-38 BMF 30-HW-39 BMF 30-HW-4 Advantages Cylinder Channel 7 14 mm dovetail e.g. De-Sta-Co mm dovetail e.g. Compact Air 4 12 mm dovetail Bracket O7 6.9 M3 4. O e.g. Norgren BMF 30-HW mm dovetail O8.8 O BMF 30-HW-47 e.g. Norgren small bore mm dovetail O16.2 O e.g. Norgren large bore BMF 30-HW-0 T-slot BMF 30-HW-2 T-Rail M3x0.-6H O3.3 2mm e.g. SMC.18

19 BMF 30 Ordering Code BMF 30-HW-3 BMF 30-HW-8 Advantages Cylinder Channel.00 T-slot e.g. PHD T-slot M Cylinder & Bracket O12 O8 BMF 30 Brackets Cylinder & BMF 30-HW-64 BMF 30-HW-67 T-slot T-slot Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

20 Installation Benefits Can be inserted into slot from above. BMF 30 Brackets BMF 30 Ordering Code BMF 30-HW-70 BMF 30-HW-71 BMF 30-HW-72 Advantages Cylinder Channel Bracket Switchpoint is set in seconds! Turn screw one revolution, adjust position, tighten. Switchpoint can't be lost. Even if you replace the sensor, the same switchpoint remains because the bracket doesn't move. Cylinder Size 1." 2" 2." 3.2" 4" " 6" 8" Bracket BMF 30-HW-70 BMF 30-HW-70 BMF 30-HW-70 BMF 30-HW-71 BMF 30-HW-71 BMF 30-HW-72 BMF 30-HW-72 BMF 30-HW-72 BMF 30-HW-76 Parker 2 MA 3/4" Ø16.2 M3x0.-6H (2X)

21 BMF 30 Ordering Code Advantages BMF 30-HW-77 BMF 30-HW-82 Cylinder Channel Tie rod 3/4" T-slot e.g. Exlar Bracket Ø Ø19.0 Cylinder & M3x0.-6H (2X) M4x0.7-6H Ø9.0 M3x.0-6H Ø BMF 30 Brackets Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

22 BMF 307 T-slot sensors BMF 307 Series Connection Type BMF 307 Cable + M08 DC Na Connector (S49) BMF 307 PuFlex Cable BMF 307 Cable + M08 DC Na Connector (S49) BMF 307 The BMF 307 magnetic field sensor is a T-slot style that fits many popular pneumatic cylinders such as Festo and SMC. The BMF 307 is a bracketless design featuring an integrated set screw in the housing LED M8x1 Max. 40 PNP NPN Normally-open Normally-closed Normally-open Normally-closed BMF 307K-PS-C-2-SA2-S49-** BMF 307K-PO-C-2-SA2-S49-** BMF 307K-NS-C-2-SA2-S49-** BMF 307K-NO-C-2-SA2-S49-** BMF 307K-PS-C-2-PU-* BMF 307K-PO-C-2-PU-* BMF 307K-NS-C-2-PU-* BMF 307K-NO-C-2-PU-* AC/DC BMF 307K-R-AS-L-3-S49-** Rated operating field strength H nl Assured operating field strength I H a I Hysteresis of I Hn I Temperature drift of turn-on point of I H n I Turn-on delay Turn-off delay Supply voltage U B Voltage drop U d Rated insualtion voltage Ui Rated operating current I e No-load supply current I 0 max. Off-state current Ir Reed contact rating max. Minimum operating current Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range Ta LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approval Recommended 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 30 ma C LCP M8 pigtail C49 ANE-00-VY-00M 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 30 ma C LCP cable, PUR 3 26 AWG 0.7 ms 0.2 ms Vac/Vdc 128 ma at 24 Vac/Vdc 10 W 3 ma 0. µf C IP 6 LCP M8 pigtail C49 ANE-00-VY-00M * Please specify the cable length for sensor. Standard lengths are as follows: 03 = 3 m, 0 = m. Consult the factory for other cable length options. **Please specify length for the pigtail. Standard lengths are as follows: 00.2 = 0.2 m, 00. = 0. m. Consult the factory for other cable length options..22

23 BMF 307 Cylinder & BMF 307 T-slot sensors BMF 307 Cable + M12 DC Micro Connector (S4) LED Max. 46 BMF 307K-PS-C-2-S4-** BMF 307 PuFlex Cable Wiring diagrams Normally-open AC/DC Reed Connector PNP/cable PNP/ NPN/cable PNP/ Normally-closed AC/DC Reed Cable Cylinder & 1.2 ka/m (1 Gauss) 2 ka/m (20 Gauss) 4 % 0.3 %/ C ac/vdc 3.1 V 30 ma C LCP M12 pigtail C04 AEL-00-VY-00M BMF 307K-R-AS-L-3-* 0.7 ms 0.2 ms Vac/Vdc 128 ma at 24 Vac/Vdc 10 W 3 ma 0. µf C IP 6 LCP cable, PVC 2 26 AWG Output current temperature curves BMF 307-HW (14.4) (14) Ø Piston Ø Inch 1 1/4 1 1/ /2 3 4 mm Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors BMF 307-HW BMF 307-HW-73-2 Tube cuffs Piston Ø Cuff Size BMF 307-HW BMF 307-HW Accessories o Product Overview t Technical Reference p Part Number Index

24 BMF 31 Replacement for T-slots BMF 31 The first choice for pneumatic cylinders with T-slot The T-slot has w become established as the standard slot type for pneumatic cylinders. Series Connection Type BMF 31 Cable + M08 DC Na Connector (S49) Rotating Threaded Connector BMF 31 PuFlex Cable To shorten assembly time, the ability to install from above is critical. max. 1, Nm max. 1, Nm The BMF 31 meets every requirement and stands out with its reliable switching characteristics and wide range of sensing performance. For especially demanding applications you can choose between weld immune or temperature rated versions. Features Proven electronics from the BMF line of sensors Can be installed in the T-slot from above Rugged, compact, low-profile housing Extremely reliable switching behavior PNP NPN Normally-open Normally-closed Normally-open Normally-closed BMF 31K-PS-C-2-SA2-S49-** BMF 31K-PO-C-2-SA2-S49-** BMF 31K-NS-C-2-SA2-S49-** BMF 31K-NO-C-2-SA2-S49-** BMF 31K-PS-C-2-PU-* BMF 31K-PO-C-2-PU-* BMF 31K-NS-C-2-PU-* BMF 31K-NO-C-2-PU-* Wiring diagrams Normally-open PNP/Cable PNP/Connector NPN/Cable NPN/Connector Normally-closed PNP/Cable PNP/Connector NPN/Cable NPN/Connector Rated operating field strength H nl Assured operating field strength I H a I Hysteresis of I H n I Temperature drift of turn-on point of I H n I Turn-on delay Turn-off delay Supply voltage UB Voltage drop U d Rated insualtion voltage U i Rated operating current Ie No-load supply current I 0 max. Off-state current I r Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range Ta LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approval Recommended * Please specify the cable length for sensor. Standard lengths are as follows: 03 = 3 m, 0 = m. Consult the factory for other cable length options. **Please specify length for the pigtail. Standard lengths are as follows: 00.2 = 0.2 m, 00. = 0. m. Consult the factory for other cable length options. 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 1 ma C PA 66 M8 pigtail culus C49 ANE-00-VY-00M 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 1 ma C PA 66 cable, PUR 3 26 AWG Output current temperature curves.24

25 BMF 31 Cylinder & BMF 31 for welding applications or use up to 10 C Series Connection Type PNP Normally-open Rated operating field strength I H n I Assured operating field strength I Ha I Noise field strength max. Noise field frequency Hysteresis of I Hn I Temperature drift of turn-on point of I H n I On delay Off delay Supply voltage U B Voltage drop U d Rated insulation voltage Ui Rated operational current I e No-load supply current I 0 max. Off-state current Ir Protected against polarity reversal Short circuit protected Load capacity Ambient temperature range T a LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approvals Recommended Other cable length on request. BMF 31M Cable + M12 (S4) Rotating Threaded Connector max. 0.3 Nm Weld Field Immune BMF 31M-PS-W-2-S4-00,3 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 200 ka/m (200 Gauss) Hz 4 % 0.3 %/ C 0 ms 0 ms 4 V 20 ma C Al M12 pigtail culus C04 AEL-00-VY-00M BMF 31M Cable + M8 (S49) Rotating Threaded Connector max. 0.3 Nm Weld Field Immune BMF 31M-PS-W-2-S49-00,3 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 200 ka/m (200 Gauss) Hz 4 % 0.3 %/ C 0 ms 0 ms 4 V 20 ma C Al M8 pigtail culus C49 ANE-00-VY-00M Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper Wiring diagrams 6Connectors Normally-open Cable Connector Output current temperature curves 7Accessories o Product Overview t Technical Reference p Part Number Index

26 BMF 31 for welding applications or use up to 10 C BMF 31 Series Connection Type BMF 31M meter cable out BMF 31M Cable + M8 (S49) Rotating Threaded Connector BMF 31M meter cable out max. 0.3 Nm max. 0.3 Nm max. 0.3 Nm Weld Field Immune temperature rated temperature rated PNP Normally-open BMF 31M-PS-W-2-PU-0 BMF 31M-PS-D-2-SA3-S49-00,3 BMF 31M-PS-D-2-SA3-PU-0 Rated operating field strength I H n I Assured operating field strength I H a I Noise field strength max. Noise field frequency Hysteresis of I H n I Temperature drift of turn-on point of I H n I On delay Off delay Supply voltage U B Voltage drop U d Rated insulation voltage U i Rated operational current I e No-load supply current I 0 max. Off-state current I r Protected against polarity reversal Short circuit protected Load capacity Ambient temperature range T a LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approvals Recommended 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 200 ka/m (200 Gauss) Hz 4 % 0.3 %/ C 0 ms 0 ms 4 V 20 ma C Al m cable, PUR 3 26 AWG culus 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 1 ma C Al M8 pigtail 3 culus C49 ANE-00-VY-00M 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4 % 0.3 %/ C 3.1 V 1 ma C Al m cable, PUR 3 26 AWG culus Other cable length on request. Wiring diagrams Normally-open Cable Output current temperature curves Connector.26

27 BMF 21 Cylinder & BMF 21 Series Connection Type BMF 21 The BMF 21 is designed with an integral swinging bracket arm that allows it to self-adjust across a wide range of cylinder diameters. This makes the BMF 21 ideal for the tie-rod and external rail profile cylinders. PNP NPN Rated operating field strength Hnl Assured operating field strength I H a I Hysteresis of I H n I Temperature drift of turn-on point of I Hn I Turn-on delay Turn-off delay Supply voltage UB Voltage drop U d Rated insulation voltage U i Rated operating current Ie No-load supply current I 0 max. Off-state current I r Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range Ta LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approval Recommended Normally-open Normally-open BMF 21 M08 DC Na Connector (S49) BMF 21K-PS-C-2-S49 BMF 21K-NS-C-2-S ka/m (1 Gauss) 2 ka/m (2 Gauss) 4% 0.3%/ C 0. ms 0. ms 3.1 V 30 ma 80 µa 1µF -2 C...+8 C PBT Hardened C49 ANE-00-VY-00M BMF 21 PuFlex Cable BMF 21K-PS-C-2-PU-* BMF 21K-NS-C-2-PU-* 1.2 ka/m (1 Gauss) 2 ka/m (2 Gauss) 4% 0.3%/ C 0. ms 0. ms 3.1 V 30 ma 80 µa 1µF -2 C...+8 C PBT Hardened cable, PUR 3 x 26 AWG Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position * Please specify the cable length for sensor. Standard lengths are as follows: 03 = 3 m, 0 = m. Consult the factory for other cable length options. Power Clamp & Gripper 6Connectors Wiring Diagram Output current temperature curve PNP/Connector NPN/Connector 7Accessories o Product Overview PNP/Cable NPN/Cable t Technical Reference p Part Number Index

28 BMF 21 BMF 21 BMF 21-HW-8 for pneumatic cylinders with tie rods Piston Ø = any Tie rod Ø mm or Pneumatic cylinders with DUO rail Piston Ø = any BMF 21-HW-10 BMF 21-HW-10E for pneumatic cylinders with tie rods Piston Ø mm Tie rod Ø mm or for pneumatic cylinders with integral tie rod (profile) Piston Ø mm Profile width mm BMF 21-HW-11 + Tube Cuff (SCHLAUCHSCHELLE BMF GR. ) for pneumatic cylinders without tie rods/rail Tube cuffs sold separately. Tube cuff sizes available for the following cylinder diameters: Pneumatic Tube Cuff Sizes Tube Cuff Size Piston Ø Cylinder Ø 0 < To order a combination kit of sensor with mounting bracket, include the bracket code in the part number. Example: BMF 21K/HW10-PS-2-C-S49.28

29 BMF 32 Cylinder & BMF 32 Series Connection Type BMF 32 The BMF 32's tough aluminum housing, compact size and rugged electronics make it the sensor of choice in tough industrial applications. The BMF 32 will perform where lesser devices call it quits. The BMF 32 is also available with a weld field immune circuit for demanding arc and reisistance welding applications. PNP Normally-open NPN Normally-open Rated operating field strength H nl Assured operating field strength I Ha I Hysteresis of I H n I Temperature drift of turn-on point of I H n I Turn-on delay Turn-off delay Supply voltage U B Voltage drop Ud Rated insualtion voltage U i Rated operating current I e No-load supply current I0 max. Off-state current I r Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range T a LED Degree of protection per IEC 6029 Housing material Connection No. of wires gauge Approval Recommended BMF 32 M08 DC Na Connector (S49) BMF 32M-PS-C-2-S49 BMF 32M-NS-C-2-S ka/m ( 1 Gauss ) 2 ka/m ( 2 Gauss ) 4% 0.3%/ C 0.0 ms 0.0 ms 3.1V 30 ma 80 µf 1µF -2 C...+8 C IP67 Al C49 ANE-00-VY-00M To order a combination kit of sensor with mounting bracket, include the bracket code in the part number. Example: BMF 32M/HW12-PS-C-2-S49 BMF 32 M12 DC Micro Connector (S4) BMF 32M-PS-C-2-S4 BMF 32M-NS-C-2-S4 1.2 ka/m ( 1 Gauss ) 2 ka/m ( 2 Gauss ) 4% 0.3%/ C 0.0 ms 0.0 ms 3.1V 30 ma 80 µf 1µF -2 C...+8 C IP67 Al C04 AEL-00-VY-00M Wiring Diagrams PNP/Connector BMF 32 M12 DC Micro Connector (S4) Weld Field Immune NPN/Connector Weld Field Immune BMF 32M-PS-W-2-S4 BMF 32M-PS-W-2-S4 1.2 ka/m ( 1 Gauss ) 2 ka/m ( 2 Gauss ) 4% 0.3%/ C 0.0 ms 0.0 ms 4 V 30 ma 80 µf 0.1 µf -2 C...+8 C IP67 Al C04 AEL-00-VY-00M Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors BMF 32 fits 12mm wide, 60 trapezoidal channel or tie rods and rails with optional brackets. See following page for bracket options. Output current temperature curves 7Accessories o Product Overview t Technical Reference p Part Number Index.29

30 BMF 32 Brackets BMF 32 BMF 32-HW-12 for pneumatic cylinders with trapezoidal rail Mecman EUROMEC Piston Ø = any BMF 32-HW-13 for pneumatic cylinders with tension rod Piston Ø = any Tie rod Ø max. 11 mm BMF 32-HW-14 for pneumatic cylinders with trapezoidal rail Bosch types /31/32/33/ 34/3 Piston Ø = any BMF 32-HW-1 for pneumatic cylinders with tie rods Piston Ø = any Tie rod Ø mm BMF 32-HW-16 for pneumatic cylinders with duo rail or tie rods Piston Ø = any.30

31 BMF 32 Cylinder & BMF 32 BMF 32-HW-18 for pneumatic cylinders with trapzoidal rail SCHLAUCHSCHELLE BMF GR. for pneumatic cylinders without tie rods/rail Pneumatic Tube Cuff Sizes Tube Cuff Piston Ø Cylinder Ø Size 0 < Cylinder & BMF 32-HW-49 for small tie rod cylinders 3/4"-1 1/8" bore e.g. PHD A, AV, HV series Bracket is secured to tie rod and leverage holds sensor firmly in position BMF 32-HW-4 for tie rod cylinders up to 10 mm diameter tie rod Bracket is secured to tie rod and leverage holds sensor firmly in position O M4x0.7-6H Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 9.7 6Connectors Ø9.7 º Ø10.8 R Accessories o Product Overview t Technical Reference p Part Number Index

32 Prox Style Prox Style Housing type Connection type Housing size BMF 07M PuFlex-cable 6. O LED Some advantages of magnetic field sensors in the classic inductive sensor housing: Large sensing distances with small sizes Sensing through walls made of n-ferrous metals like aluminum, without reduced sensing distances Reacts only to magnetic fields; faulty switching by metal shavings or other metal parts Magnet can be flush mounted in steel Protected against polarity reversal Supply voltage Reacts to the rth or south poles Solid-state Wear-free Vibration insensitive Output protected against inductive peaks Short circuit protected PNP Normally-open NPN Normally-open Rated operating field strength Hn Assured operating field strength H a Differential travel Temperature drift Switch on response time Switch off response time Supply voltage UB Voltage drop U d at l e 100 ma Rated insulation voltage U i Rated operational current I e No-load supply current I 0 d./und. Off-state current I r Protected against polarity reversal Short circuit protected Load capacitance Ambient temperature range T a LED Degree of protection per IEC 29 Housing material Connection No. of wires size Approvals Recommended BMF 07M-PS-C-2-KPU-03 BMF 07M-NS-C-2-KPU ka/m (1 Gauss ) 2 ka/m (2 Gauss ) 4 % 0.3 %/ o C 3.1 V 22 ma/ 10 ma C nickel plated brass cable, PUR 3 x 26 AWG Wiring diagrams PNP/Cable PNP/Connector Output current temperature curves NPN/Cable NPN/Connector.32

33 Prox Style Cylinder & Prox Style Ø 6. mm, M8, M12 BMF 07M Cable + M8 (S49) Rotating Threaded Connector Ø 6. BMF 07M-PS-D-2-SA2-S49-00,3 BMF 07M-NS-D-2-SA2-S49-00,3 1.2 ka/m (1 Gauss ) 2 ka/m (2 Gauss ) 4 % 0.3 %/ o C 3.1 V 30 ma C nickel plated brass cable with, PUR culus C49 ANE-00-VY-00M BMF 07M Cable + M12 (S4) Rotating Threaded Connector Ø 6. BMF 07M-PS-D-2-S4-00,6 1,2 ka/m (1 Gauss ) 2 ka/m (2 Gauss ) 4 % 0.3 %/ o C 3.1 V 30 ma C nickel plated brass cable with, PUR culus C49 ANE-00-VY-00M BMF 08M PuFlex-cable 13 M8 M8x1 30. LED BMF 08M-PS-C-2-KPU-03 BMF 08M-NS-C-2-KPU ka/m (1 Gauss ) 2 ka/m ( 2 Gauss ) 4 % 0.3 % / o C 3.1 V 30 ma C nickel plated brass cable, PUR 3 26 AWG BMF 12M M12 DC Micro (S4) 17 M BMF 12M-PS-D-2-S4 BMF 12M-NS-D-2-S4 1.2 ka/m ( 1 Gauss ) 2 ka/m ( 2 Gauss ) 4 % 0.3 % / o C 3.1 V 12 ma/ 10 ma C nickel plated brass C04 AEL-00-VY-00M Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Operating Magnets Magnet type Samarium Cobalt Ferrite Strontium Ferrite Power Clamp & Gripper 6Connectors 7Accessories Ordering codes Nominal Dimensions Thickness Assured operating distance Sa Differential travel MAGNET PLATTE 16x12x mm 3 mm 28 mm 8 mm RUNDMAGNET 10.0x mm 10 mm 1 mm 2 mm RUNDMAGNET 4.0x.0 4 mm mm mm 2 mm o Product Overview t Technical Reference p Part Number Index

34 separation Installation Hints The response travel of a magnetic field sensitive sensor is virtually independent of the field strength of typical piston magnets. Still the sensor does t exhibit false switching. When using more than one of the magnetic field switches, the BMF sensors can be mounted directly next to or beside each other. Installation Adjustment and mounting 1. Set piston to end of travel. 2. Slide sensor (with power on) until the output turns on (LED on). Mark the location of the front edge of the sensor on the cylinder body. 3. Continue to slide the sensor until the output is off (LED off). 4. Change direction and slide the sensor back towards the other end of the cylinder. When output turns on, mark location of the same sensor edge (original front edge) on the cylinder body.. The two marks on the cylinder body define the width of the zone of the sensor with this cylinder. Determine the midpoint of the two marks and lock down the sensor so the original front edge is located at this midpoint..34 Use in weld fields Weld-immune magnetic field sensors can be operated in external fields up to a field strength of E max = 200 ka/m. This limit is often exceeded in the direct vicinity of high current lines, e. g. welding equipment. The sensor should therefore be mounted at a distance d min from such lines, as shown in the diagram at right showing the relationship between current and conductor diameter. Weld-immune sensors include: BMF 32M...W... BMF 30M...W... BMF 31M...W... BMF 30K...W...

35 Techlogy Cylinder & BMF Techlogy Comparison Operating principle Solid-state, wear-free operation Radio frequency immunity Required magnetic field strength Switching speed Contact bounce Susceptibility to damage by AC welding fields Susceptibility to false tripping by AC welding fields Works with magnet type Required magnetic polarity orientation BALLUFF Magnetoresistive (MR) Giant Magnetoresistive (GMR) Change of resistance/current Yes Moderate Low to high High No Low WFI versions, ne to low Hall Effect or Reed Magnet* MR Perpendicular or Parallel GMR Parallel BMF Techlogy Comparison Hall Effect Microvolt signal Yes Low High High No Low High Hall Effect Magnet only Perpendicular only Reed Switch Mechanical contact No High High Low Yes High High Reed Magnet only Parallel only Cylinder & Susceptible to double switchpoints Output short circuit protection Output reverse polarity protection Output overload protection Kw your cylinder? Find your sensor. No* Yes Yes Yes Yes Sometimes Sometimes Sometimes Yes No Yes (bipolar) *Always test in actual application. Some Hall Effect magnets will t trigger sensor reliably; others may cause double switch points. No It's that easy with Balluff's Pneumatic Cylinder Sensor Resource Center... - Over 1000 cylinders cataloged - Lifetime warranty on all solid state cylinder sensors Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

36 Precision in a compact housing BIL is the compact displacement sensor for position sensing up to 160 mm. The BIL analog position sensor utilizes n-contact magnetic inductive techlogy to provide continuous, absolute position feedback. BIL Analog Position Sensor Output signal U a Output signal I a Working range s a Linear range s I Voltage V or Current mA mm... mm BIL Features Power and magnet indicator LEDs (AMDO & EMDO) Magnet missing/out of range max output value indication (AMDO & EMDO) Non-contact Wear-free Suitable for harsh environments with potted sensor and electronics Processing electronics integrated, external components Housing cross-section 1 1 mm Applications Robotics/handling Clamping cylinders Packaging Process industry Position sensing on grippers Installation tes When installing and attaching the BIL and magnet, nmagnetizable materials such as alloys, austenitic steels, plastics, etc. are recommended. This applies both to the sensor as well as the magnet. Magnetizable materials can affect the geometry and strength of the field coming from the permanent magnet. Magnetic fields in the area of the BIL can, depending on their orientation and strength, affect the output signal. Ordering code 0-10 Vdc 0-10 Vdc / 4-20 ma Rated operational voltage U e Supply voltage U B Ripple Rated insulation voltage U i Rated sensing distance s e Load resistance R L No-load supply current I 0 at U e Protected against polarity reversal Short circuit protected Supply voltage indication Position marker inside/outside working range Ambient temperature range T a Repeat accuracy R BWN Non-linearity Limit frequency ( 3dB) Measuring speed Temperature coefficient TK typ. in the optimal range min. from C max. Degree of protection per IEC 6029 Housing material Connection Recommended Wiring diagrams BIL AMD0... t used BIL ED0 & EMD0... Connect to either voltage or current output. Recommended distances from magnetizable materials (for optimum function) BIL AMD0-T060A-01-S7 BIL EMD0-T060A-01-S Vdc 10 % of Ue 30 mm at Ua 2 kω, at Ia 00 Ω 30 ma (LED 1) (LED 2) C ±60 µm ±1 mm 100 Hz m/s + µm/k 20 µm/k +2 µm/k PA fiberglass reinforced C7A or C7B Output Curve l a U a BIL AMD0 & EMD all data in mm

37 BIL Sa mm, mm, V or ma distance "D" between magnet and sensor, see page.39 Voltage V or Current ma mm... mm BIL ED0-P060A-01-S7 at U a Vdc, at I a 10 % of Ue 30 mm at Ua 2 kω, at Ia 00 Ω 30 ma C ±60 µm ±0.6 mm 100 Hz m/s µm/k +1 µm/k 2 µm/k PA fiberglass reinforced C7A or C7B Output Curve BIL ED0... unusable area indexing slot 0 V voltage 10 V 4 ma current 20 ma unusable area distance "D" between magnet and sensor, see page.39 unusable area Voltage V or Current ma mm mm 0 V voltage 10 V 4 ma current 20 ma indexing slot BIL ED0-P160A-01-S7 at U a Vdc, at I a 10 % of Ue 80 mm at Ua 2 kω, at Ia 00 Ω 2 ma C ±80 µm ±2.4 mm 300 Hz m/s 40 µm/k +120 µm/k 200 µm/k PA fiberglass reinforced C7A or C7B unusable area Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview The original bracket and screws are recommended for mounting the BIL. Please order accessories separately. See page.39. t Technical Reference p Part Number Index.37

38 Output signal U a Output signal Ia Working range s a Linear range s I Micro-BIL For Analog Position Sensor Voltage V or current ma mm mm BIL 300 mm button Ordering code Field strength axial Hn 3dB width of axial field distribution, typical (axial field strength typ. parallel to ) Rated operational voltage Ue Supply voltage U B Ripple Rated insulation voltage Ui Rated sensing distance s e Load resistance R L No-load supply current I 0 at U e Protected against polarity reversal Short circuit protected Ambient temperature range T a Repeat accuracy R BWN Non-linearity Temperature coefficient TK typical in the optimal range min. from C max. Supply voltage indication Programming indication Degree of protection per IEC 6029 Housing material Connection Recommended BIL ED0-B010P-02/30-S7 10 ka/m typical 2. mm at U a Vdc, at I a 10 % of U e mm at U a 2 kω, at I a 00 Ω 30 ma C ±30 µm ±0.3 mm +4 µm/k +2 µm/k +10 µm/k PA fiberglass reinforced C7A or C7B Wiring diagram V output ma output Connect to either voltage or current output. Micro-BIL is the solution for continuous position sensing on pneumatic miniature grippers with T-slot. The analog output signal allows you to sense end-of-travel and intermediate positions of gripper jaws absolutely and without contact. To use the Micro-BIL a magnet is installed in the gripper. A button is provided for calibrating to various magnetic field strengths. The technical data refers to reference measurements. Different grippers with differing magnetic field strengths may affect the technical data. Output curve.38

39 BIL Cylinder & BIL Accessories Description Dimensions Material Distance "D" Ordering code Description Material Magnet Hard ferrite 2 mm BIL 000-MH-A Bracket stainless steel Magnet PA fiberglass reinforced 1 mm BIL 001-MH-A Bracket stainless steel Analog Set Point Controller M18 1 CuZn nickel plated C7 ENL-04-VY-003M BES _S-1-PU-0 Analog output PNP or NPN rmally- open Input signal V Resolution 8 bits 3 binary switch points Teach-in programming See page 7.34 for technical information Bracket stainless steel Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper Ordering code BIL 01-HW-1 BIL 01-HW-2 BIL 01-HW-3 6Connectors Installation Examples 7Accessories o Product Overview t Technical Reference p Part Number Index

40 .40 Cylinder &

41 Inductive Cylinder Balluff s cylinder-position sensors provide precision end-of-stroke sensing for hydraulic cylinders. The sensor body allows 304 of rotation to eliminate the hassle of postinstallation cable management, which in some competitive designs requires unbolting the flange and breaking the hydraulic seal. A high-pressure, inductive proximity sensor, the Strokemaster provides a 2mm (0.08") sensing range to detect the spud of hydraulic/ pneumatic cylinders and indicate fully retracted or extended position. It mounts with two socket-head cap screws and seals with a Viton O-ring. Withstanding cylinder pressures up to 3000 PSI (207 bar), the embeddable design keeps most of the switch protected within the cylinder, with only a 0.62" (16 mm) high housing exposed outside. Strokemaster sensors are available in 3-wire DC and 2-wire AC/DC versions, both with mini or micro s. Switching frequency is 0 Hz for the AC/DC versions. All units are weld-field immune, short-circuit, and reversepolarity protected. They fit all popular cylinder designs, with standard available probe lengths of 0.912" " (23.16mm mm). Custom probe lengths can be achieved by using factory spacer kits. Probes are made of stainless steel with a high-strength ceramic face. Both DC and AC/DC sensors have all-metal housings. The Strokemaster sensor is CE-certified, and its housing is sealed to IP67 requirements..42 DC.43 AC/DC.44 Technical Information Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

42 DC s n 2 mm Rated operating distance s n Assured operating distance s a Flush 2 mm mm PNP Normally-open! Rated operational voltage U e Supply voltage U B Voltage drop U d at l e Rated insulation voltage U i Rated operational current I e No-load supply current I 0 damped/undamped Off-state current I r Protected against polarity reversal Short circuit/overload protected Load capacitance Repeat accuracy R Ambient temperature range Ta Operating frequency f Utilization categories Function/Operating voltage indication Degree of protection per IEC 6029 Housing material Material of sensing face Connection Approvals High pressure rated up to Standard lengths (L) Recommended BES S 29/0.912" "-S4 2. V 18 ma/ 10 ma / 1.0 µf % C 10 Hz DC 13 / stainless steel/aluminum ceramic micro culus 207 bar (3000 psi) see table on page.44 C04 AEL-00-VY-00M Bolt sensor to cylinder. Position cable to desired orientation (even over mounting bolts). Lock chosen position with one or both of the two integral set screws. Note: Some DC units are also available with S Mini. Consult factory for sensor and cable part numbers..42

43 AC/DC s n 2 mm Rated operating distance s n Assured operating distance sa AC/DC Wiring Diagrams! 30 PNP N/O AC/DC N/O w/ Gnd. 1 GRN RD/BLK RD/WH LED 1 LED 2 Normally-open Rated operational voltage Ue Supply voltage U B Voltage drop U d at l e Rated insulation voltage Ui Rated operational current I e Minimum operational current I m Off-state current Ir Inrush current I k (t = 20 ms) Protected against polarity reversal Short circuit protected Repeat accuracy R Ambient temperature range T a Operating frequency f Utilization categories Function/Operating voltage indication Degree of protection per IEC 6029 Insulation class Housing material Material of sensing face Connection Approvals High pressure rated up to Standard lengths (L) Recommended Flush 2 mm mm BES S 2/0.912" "-S Vac Vac/Vdc 6 V 20 Vac 00 ma ma 1.7 ma at 110 Vac 3 A max./1 Hz % C 0 Hz AC 140/DC 13 / 1 stainless steel/aluminum ceramic micro culus 207 bar (3000 psi) see table on page.44 C21 AE3-00-VY-10F Flush 2 mm mm UNC 1/4-20x3/ UNC 1/4-20x3/ O-ring X 2.62 O-ring X 2.62 ½ UNF-20-2A 7/8-16 UN 7 O12.7 L L O12.7 BES S 2/0.912" "-S 110 Vac Vac/Vdc 6 V 20 Vac 00 ma ma 1.7 ma at 110 Vac 3 A max./1 Hz % C 0 Hz AC 140/DC 13 / 1 stainless steel/aluminum ceramic mini culus 207 bar (3000 psi) see table on page.44 C0 AE1-00-VY-10F 64.2 Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

44 Installation & Spacers Installation Note: Spacer may be required to elevate cylinder sensor to position sensing face in optimal position. Balluff recommends the following guidelines when mounting our sensors: A - Recommended to allow for Spacers mechanical wear (0.02" to 0.047") B - This dimension must be large eugh to allow the sensor to turn off when the rod is present (0.110" to 0.118") Probe length (inches) Below is a table to help you pick out a spacer for custom lengths needed with sensors: Z/Spacers (inches) Example: Need probe length of 1.12" combine sensor BES S2-1.3-S21 with a 0.22" spacer. (1.3" tube length " spacer = 1.12" adjusted length) Note: A difference of 0.00" will still have to be carefully considered when sizing a spacer and sensor to the cylinder. - Spacer kits include a spacer, "O" ring, and appropriate mounting screws. - Other spacer kits may be available: consult factory. To order a spacer kit: Use part number BESA KIT-* (X.XXX) *measured in inches (For both DC and AC/DC devices - there is difference in flange dimensions).44

45 Cylinder & Introduction Inductive Cylinder Balluff offers a world-class line of pressurerated inductive cylinder sensors to service high pressure applications. Designed to withstand severe duty, Balluff high pressure sensors deliver reliable switching performance under demanding industrial conditions. Corrosion-resistant housing materials, highstrength ceramic sensing faces, and special sealing techniques allow dependable service up to 30 bar or 00 bar according to the sensor type. All Balluff high pressure sensors are rated for continuous operation in ambient temperatures up to 90 C, with some versions also hightemperature rated up to 120 C..46 DC 3-wire M8, M12.48 DC 3-wire M16.49 DC 3-wire M18.0 Extended Temperature DC 3-wire M12, M18.1 Extended Range M12.2 Power Clamp & Gripper Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper of Pressure Rated with O-Ring d1: of bore for switch head, 10 H8 = d2: minal thread diameter, 6H L: recommended insertion depth L 0.8 d2 H8 Note: To ensure sealing under extremely high pressure, the sensors are supplied with an O-ring and a PTFE supporting ring. The 1 to 30 chamber is required to avoid damage to the O-ring when the sensor is inserted. thread undercut D DIN 76 6H 0.6 O-ring-cord diameter assembly direction 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

46 DC 3-Wire M8, M12 S n 1. mm Housing size Rated operating distance s n Assured operating distance s a M8 1 flush 1. mm mm M12 1 flush 1. mm mm M12 1 flush 1. mm mm M12 1 flush 1. mm mm O-Ring 12.9 O-Ring 12.9 O-Ring PNP Normally-open! BES S289-BO-D-PU-0 BES S292-BO-D-PU-0 BES S162-S4-D BES S163-S4-D BES S164-S4-D NPN Normally-open $ BES S242-S4-D Rated operational voltage U e Supply voltage U B Voltage drop U d at l e Rated insulation voltage U i Rated operational current I e No-load supply current I0 d./und. Off-state current I r Protected against polarity reversal Short circuit/overload protected Load capacitance Repeat accuracy R Ambient temperature range Ta Operating frequency f Utilization categories Function indication Degree of protection per IEC 6029 Housing material Material of sensing face Connection No. of wires gauge High pressure rated up to Recommended Vdc 1 V 10 ma 0 µa 0.2 µf 1 % C 6000 Hz DC 13 stainless steel ceramic cable 3 x 26 AWG 100 bar (140 psi) 2 V 10 ma/ 2 ma / 1.0 µf % C 2000 Hz DC 13 IP 68 stainless 430F EP 00 bar (720 psi) C04 AEL-00-VY-00M 1. V 8 ma/ 1 ma / 0. µf % C 1000 Hz DC 13 IP 68 stainless 430F EP 00 bar (720 psi) C04 AEL-00-VY-00M 1. V 20 ma/ 12 ma / 0. µf % C 1000 Hz DC 13 IP 68 stainless 430F EP 00 bar (720 psi) C04 AEL-00-VY-00M Other cable lengths may be available. Additional models may exist. Replacement o-rings and support rings are also available. Consult factory or company website for details. Accessory seal nut: BES 08-DM-1 (see page 7.13) O10e O10e O10e PNP N/O PNP N/C PNP N/O & # NPN N/O NPN N/C NPN N/O & N/C $ % ^.46

47 Cylinder & DC 3-Wire M12 S n 1. mm M12 1 flush 1. mm mm BES S281-S4-D O-Ring 17 M12 1 flush 1. mm mm BES S26-S4-D M12 1 flush 1. mm mm BES S240-D-PU-0 BES S241-D-PU-0 M12 1 flush 1. mm mm BES S249-S4-D M12 1 flush 1. mm mm BES S13-S4-D Cylinder & 1. V 130 ma 2 ma/ 1 ma / 1.0 µf % C 1000 Hz DC 13 IP 68 stainless 430F EP 00 bar (720 psi) C04 AEL-00-VY-00M 2.0 V 10 ma/ 2 ma / 1.0 µf % C 2000 Hz DC 13 IP 68 stainless 430F EP 00 bar (720 psi) C04 AEL-00-VY-00M O10e V 20 ma/ 12 ma 10 µa / 1.0 µf % C 2000 Hz DC 13 IP 68 stainless 430F EP cable 3 24 AWG 00 bar (7200 psi) 2.0 V 10 ma/ 2 ma 10 µa / 1.0 µf % C 2000 Hz DC 13 IP 68 stainless 430F EP 00 bar (720 psi) C04 AEL-00-VY-00M O10e V 10 ma/ 1 ma 10 µa / 0. µf % C 1000 Hz DC 13 IP 68 stainless 430F EP 00 bar (720 psi) C04 AEL-00-VY-00M O10e Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

48 DC 3-Wire M12, M16 S n 1. mm Housing size Rated operating distance s n Assured operating distance s a M12 1 flush 1. mm mm M12 1 flush 1. mm mm M12 1 flush 1. mm mm M16 1 flush 1. mm mm M16x1 O14e7 O-Ring O-Ring Ø1 14 PNP Normally-open! BES S20-D-PU-0 BES S262-S4-D BES S13-D-PU-0 BES S178-D-PU-0 BES S12-S4-D Rated operational voltage U e Supply voltage U B Voltage drop U d at l e Rated insulation voltage U i Rated operational current Ie No-load supply current I 0 d./und. Off-state current I r Protected against polarity reversal Short circuit/overload protected Load capacitance Repeat accuracy R Ambient temperature range T a Operating frequency f Utilization categories Function indication Degree of protection per IEC 6029 Housing material Material of sensing face Connection No. of wires gauge High pressure rated up to Recommended Other cable lengths may be available. Additional models may exist. Replacement o-rings and support rings are also available. Consult factory or company website for details. 2.0 V 10 ma/ 2 ma 10 µa / 1.0 µf % C 2000 Hz DC 13 IP 68 stainless 430F EP cable 3 24 AWG 30 bar (000 psi) O10e V 10 ma/ 2 ma 10 µa / 1.0 µf % C 2000 Hz DC 13 IP 68 stainless 430F EP 00 bar (720 psi) C04 AEL-00-VY-00M O10e V 10 ma 10 µa 0. µf % C 1000 Hz DC 13 IP 68 stainless steel EP cable, PUR 3 x 26 AWG 00 bar (720 psi) 1. V 8 ma/ 1 ma 10 µa / 0. µf % C 1000 Hz DC 13 IP 68 stainless 430F EP 30 bar (000 psi) C04 AEL-00-VY-00M M16x1 O14e7 PNP N/O PNP N/C PNP N/O & # NPN N/O NPN N/C NPN N/O & N/C $ % ^.48

49 Cylinder & DC 3-Wire M16, M18, Ø 10 mm, Ø 36 mm S n 1. mm, 3 mm O-Ring 22 M16 1 flush 1. mm mm 14 M16x1 O14e BES S149-S4-D BES S16-S4-D O-Ring M18 1 flush 1. mm mm M18x1 O14e7 13 M20 8 BES S144-S4-D 73 M18 1 flush 3 mm mm BES S190-S4 Ø 10 mm/ø 36 mm flush 1. mm mm BES S260-S4-D Cylinder & 1. V 1 ma/ 12 ma 10 µa / 0. µf % C 1000 Hz DC 13 IP 68 stainless 430F EP 30 bar (000 psi) C04 AEL-00-VY-00M M16x1 O14e V 8 ma/ 1 ma 10 µa / 0. µf % C 1000 Hz DC 13 IP 68 stainless 430F EP 30 bar (000 psi) C04 AEL-00-VY-00M M18x1 O14e V 130 ma 2 ma/ 12 ma / 1.0 µf % C 400 Hz DC 13 IP 68 stainless 430F PEEK 00 bar (720 psi) C04 AEL-00-VY-00M 2.0 V 10 ma/ 2 ma 10 µa / 1.0 µf % C 2000 Hz DC 13 IP 68 stainless 430F EP 30 bar (000 psi) C04 AEL-00-VY-00M 3.8 Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

50 DC-3 Wire M12, M18 s n 1. mm Extended Duty Housing size Rated operating distance s n Assured operating distance s a M12 1 flush 1. mm mm M12 1 flush 1. mm mm M18 1 flush 1. mm mm Ø10e7 Ø10e7 O-Ring O-Ring O-Ring Extended Temperature Extended Temperature Extended Temperature PNP Normally-open! BHS B13V-PSD1-S04 BHS B249V-PSD1-S04 BHS E308V-PSD1-S04 Rated operational voltage U e Supply voltage U B Voltage drop U d at l e Rated insulation voltage U i Rated operational current I e No-load supply current I 0 d./und. Off-state current I r Protected against polarity reversal Short circuit/overload protected Load capacitance Repeat accuracy R Ambient temperature range Ta Operating frequency f Utilization categories Function indication Degree of protection per IEC 6029 Housing material Material of sensing face Connection No. of wires gauge High pressure rated up to Recommended 2. V 8 ma 10 µa 0. µf % C 400 Hz DC 13 IP 68 stainless steel ceramic 00 bar (720 psi) C04 AEL-00-VY-00M 2. V 8 ma 10 µa 0. µf % C 400 Hz DC 13 IP 68 stainless steel ceramic 00 bar (720 psi) C04 AEL-00-VY-00M 2. V 8 ma 10 µa 0. µf % C 400 Hz DC 13 IP 68 stainless steel ceramic 00 bar (720 psi) C04 AEL-00-VY-00M Extended Temperature Models Provide high pressure rating of 00 bar Allow use in higher ambient temperature environments up to 120 C! PNP N/O.0

51 Extended Duty Cylinder & DC-3 Wire M12 s n 2. mm O-Ring M12 1 flush 2. mm mm Ø10e Extended Range BHS B13V-PSD2-S V 8 ma 10 µa 0. µf % C 400 Hz DC 13 IP 68 stainless steel ceramic bar (720 psi) C04 AEL-00-VY-00M O-Ring M12 1 flush 2. mm mm Ø10e Extended Range BHS B249V-PSD2-S V 8 ma 10 µa 0. µf % C 400 Hz DC 13 IP 68 stainless steel ceramic 00 bar (720 psi) C04 AEL-00-VY-00M O-Ring M12 1 flush 2. mm mm Ø10e Extended Range BHS B26V-PSD2-S V 8 ma 10 µa 0. µf % C 400 Hz DC 13 IP 68 stainless steel ceramic 6 00 bar (720 psi) C04 AEL-00-VY-00M Simulation (FEM method) of the stress distribution under high pressure on housing and ceramic cap Extended Range Models Provide extended sensing ranges of 2. mm High pressure rated to 00 bar Temperature rated to +90 C Cylinder & Selection Guide Magnetic Field BMF 103 BMF 273 BMF 303 BMF 30 BMF 307 BMF 31 BMF 21 BMF 32 BMF Prox Style Installation/ BIL Magneto- Inductive Cylinder Position Power Clamp & Gripper 6Connectors 7Accessories o Product Overview t Technical Reference p Part Number Index

52 Power Clamp & Gripper Clamp & Gripper Description Rated operating distance s n The Power Clamp & Gripper Large Sensing Coils 2 mm Small Sensing Coils 2 mm Small Sensing Coils 2 mm These sensors are specifically designed for use in power clamp and gripper applications. These devices incorporate two sensors into one unit, reducing the number of sensors and connection systems required for applications. Each sensor has two sensing coils (chicklets) that are used to detect whether the clamp/ gripper is in the open or closed position. 20 Cable length LED 1 LED 2 LED The base has a compatible mounting configuration for the cartridges used by the major clamp manufacturers. PNP N/O BES Z02KR2-PSC20F-P*-S04-V BES Z02KR1-PSC20F-P*-S04-V BES Z02KR3-PSC20F-P100-S04-V Rated operational voltage Load current Leakage current Voltage drop Repeatability Hysteresis Pulse protection Noise protection Short circuit protection Overload protection Weld field immunity Approvals Protection class Housing material Material of sensing face Cable material Operating temperature LED Connector * Cable lengths are: * P100 = 100 mm * P16 = 16 mm * P200 = 200 mm 10 ma 10 ma 2. V 2 % % 1600 Gauss culus, CE plastic plastic PUR C Gn = PWR, Org = S1, Rd = S2 C04 AEL-00-VY-00M 10 ma 10 ma 2. V 2 % % 1600 Gauss culus, CE plastic plastic PUR C Gn = PWR, Org = S1, Rd = S2 C04 AEL-00-VY-00M 10 ma 10 ma 2. V 2 % % 1600 Gauss culus, CE plastic plastic PUR C Gn = PWR, Org = S1, Rd = S2 C04 AEL-00-VY-00M Features Superior LED visibility Weld-field immune Shielded construction Short circuit protection Overload protection Transient ise protection False pulse protection Reverse polarity protection culus and CE certified.2