Pressure-Measuring Tool SMO Nr.: VR
|
|
|
- Benjamin Cameron Hudson
- 5 years ago
- Views:
Transcription
1 Pressure-Measuring Tool SMO Nr.: VR
2 Part List: Pressure Gauge -1/+9 Bar Pressure Gauge 2.5 Bar Pressure Gauge 250 mbar Adapter Connecting Hose/Gauge Measuring Adapter M18x1.5 Measuring Adapter M12x1.5 Measuring Adapter M14x1.5 Measuring Adapter M10x1 Measuring Adapter M12x1.5 Fuel Pressure / Oil Pressure Raw Water Pressure / Coolant Pressure Exhaust Backpressure Raw Water Pressure Exhaust Backpressure / Oil Pressure Fuel Pressure Coolant Pressure Oil Pressure (double hollow screw)
3 General 1) Always use new Copper Rings when using the STEYR MOTORS Pressure- Measuring Tool (Copper Rings are not included). 2) After measurement is finished, always put Ventilation Cap on the Measuring Gauge.
4 Coolant Pressure Engine must be cold!!! 1) Remove HEX.SOCK.SCR.PLUG WITH RUBBER SEAL M10x1. 2) Place M10x1 Adapter and tighten it with pliers. 3) Connect pressure kit hose and use the 2,5 Bar- Manometer The maximum allowed coolant pressure is 1.6 Bar.-
5 Raw Water Supply Pressure Engine must be turned off before working with the manometer. 1) Remove zinc anode (SW 23). 2) Place M18x1.5 Adapter with Copper Seal Rings. Adapter is marked with number 40. 3) Tighten it with a torque of 35Nm+/- 2 4) Connect pressure kit hose and use the 2.5 Bar- Manometer You will find the correct values in the lists of the Operators Manual / Service Manual-Chapter General.
6 Oil Pressure after Oil Filter before Bearing Road a. Engine must be turned off before working with the manometer. b. While measuring the oil pressure, engine must be in hot (working) conditions. 1) Remove HOLLOW SCREW M12x1,5 (SW 17) 2) Place M12x1,5 Hollow Screw- Adapter with Copper Seal Rings. Adapter is marked with number 88. 3) Tighten it with a torque of 20Nm+/- 2 4) Connect pressure kit hose and use the 9 Bar- Manometer Oil Pressure can be 1 7 Bar depending on engine behaviour. The max. allowed delta of oil pressure measured after the oil filter and after the bearing road (oil pressure sensor) should not be more than 1,3 bar.
7 Oil Pressurer after Bearing Road Engine must be turned off before working with the manometer. 1) Remove Hollow Screw 2) Place M12x1,5 Double Hollow Screw Adapter with Copper Seal Rings. 3) Tighten it with a torque of 28Nm+/- 2 4) Oil Pressure after Bearing Road must be compared with the oil pressure schemata Steyr Motors Webpage. Oil Pressure can be 1 7 Bar depending on engine behaviour. The max. allowed delta of oil pressure measured after the oil filter and after the bearing road (oil pressure sensor) should not be more than 1,3 bar.
8 Fuel Pressure after Fuel Pump before Fuel Filter Engine must be turned off before working with the manometer. 1) Remove HOLLOW SCREW M14x1,5 (SW 19) 2) Place M14x1,5 Hollow Screw Adapter with Copper Seal Rings. Adapter is marked with number 89. 3) Tighten it with a torque of 30Nm+/- 2 4) A correct functioning Fuel System should have a min. pressure of 3.5 Bar. If the measured fuel pressure is too high indicator for a blocked fuel filter It depends on the Fuel specification and Fuel Temperature. You will find the correct values in the lists of the Operators Manual / Service Manual-Chapter General. The max. (delta) ΔP should not be more than 0,7 bar. Measured via EDT 2.0 (FSP-sensor) compared with the manometer.
9 Exhaust Back Pressure Engine must be turned off before working with the manometer. 1) Loosen 2x Hex Head Screw M8x20 2) Loosen Hex Head Bolt M8x120 3) Remove Bracket Support. 4) Remove Exhaust Temperature Sensor (SW 17) 5) Place M12x1,5 Adapter with Copper Seal Ring. Adapter is marked with number 18. 6) Tighten it with a torque of 20Nm+/- 2 7) Exhaust back pressure according Data list in manuals You will find the correct values in the lists of the Operators Manual / Service Manual-Chapter General.
Installation Instruction for Kit Oil filter Ext. L=1,2m; Kit- P./No. Z
Table of contents 1. Technical Specifications page 1 2. Parts page 1,2 3. Installation Instruction page 3-6 1. Technical Specifications Oil-hose-extension from original engine-oil filter position = 1,2m
2600/2700 Series. Determining the stud length number when using receptacle: Type 1 + 3* G = P + F. * For Type 3: G = 9,9 mm min.
Particular Features Max. tensile strength 1.330 N. Small-size fastener for high tensile load. Wide variety of conventional stud assembly and receptacle designs. 2600 Series: Fillister head; 2700 Series:
Worm gear. Worm Gears. Description. Special features. Customer specific
Worm gear Worm Gears 2010 Description Worm gear for universal applications Center distance 20 mm Compact design Outer dimensions 60x60x35 mm 7 ratios of 13:1 to 65:1 Aluminium housing, anodized Maintenance-free
1. Main structure. Main structure Jet-288 Exploded views. Bearings and impeller shaft
Main structure 1. Main structure Code 288A 288C 288D 288E 288F 288G 288H 288I A B Name Frame Bearings and impeller shaft Impeller Stator Steering nozzle Reversing deflector Hydraulic cylinder Hydraulic
1. Main structure. Main structure Exploded views, AJ 288. Bearings and impeller shaft
Main structure 1. Main structure Code 288A 288C 288D 288E 288F 288G 288H 288I A B Name Body Bearings and impeller shaft Impeller Stator Steering nozzle Reversing deflector Hydraulic cylinder Hydraulic
1. Main structure. Main structure JET-230 Exploded views
Main structure 1. Main structure 230A Hull 230F Steering nozzle 230C Bearing and main shaft 230GT Reversing deflector* 230D Impeller 230HH Actuating cylinder 230E Stator 230I Hydraulic pump 230B Cavitation
40-501, , ,
-9 Silencer, plastic. -5, -5 Silencer, sintered bronze. - Flow control silencer. -5 Check valves. -5 Hand sliding valves. -5, -5 Quick couplings. -5 Miniature regulator, screw-in type.6-55 Check valves.7-56,
Universal instructions CNG Tank-sets. MODEL year 2011 SET Number. NUMMER : DATE : Copyright Prins Autogassystemen B.V VERSIE NR : DB
Universal instructions CNG Tank-sets Make universal MODEL year 2011 SET Number all NUMMER : DATE : 2011-09-12 TABLE OF CONTENTS... 1 Required equipment / tools / materials for installing a complete system...
BOMBARDIER - ROTAX GESELLSCHAFT M.B.H. MOTORENFABRIK. 1) Subject: 3) Concerned:
1) Subject: Checking of the tapped hole 0 in crankcase at cylinder no. 2. 2 )R eason: It was noticed that in some crankcases the thread 0 forthe helicoilinsert@foranchorage studofcylinder and cylinder
Installation instruction do88 Intercooler for Volvo S60 V70 XC70 S80 Turbo 00-09
Installation instruction do88 Intercooler for Volvo S60 V70 XC70 S80 Turbo 00-09 1. This instruction shows how to replace the OEM intercooler with our performance intercooler. At this type of installation
STANDARD PROGRAMME Hydraulic Chucks
20 STANDARD PRORAMME STANDARD PRORAMME 23 Hydraulic Chuck ISO 7388-1, Form AD (prev. DIN 69871-AD), extra short design d 1 d 2 d 3 l3 ISO 7388-1 Form AD 3 µm h6 2.5 25000 min Nominal size SK/ISO Dimensions
15 Flow Meter SCQ. Measurement principle: spring/piston system
15 Flow Meter SCQ Measurement principle: spring/piston system Flow measurement with direction indication Response time < 2 ms Compact design Withstands pressures up to 420 bar Wide range of viscosity p/t/q
SAN JUAN ENGINEERING & MANUFACTURING CO. 766 Marine Drive Bellingham, WA USA PH: (360) FAX: (360)
SANJUAN FRESH WATER COOLING Remove automatic drain, (a) Locate the SYSTEMSt automatic drain reservoir (ADR) on the front, right side and mounted low. (Gray plastic unit with blue plastic drain plug). 4.3/5.0/5.7
Spare parts P/N Description. Q 0R Kit idroguida nr.5:
To All Lamborghini Dealers and Licensed Service Point. From After Sales Department. Subject Power Steering Update. Group 10.02.00 Date 07/09/2012 Pages 12 Subject Power steering update. Model 1. Gallardo
English N4.85. Reference : Date : 12/2007 Version : A. This photograph does not necessarily represent the engine
English N4.85 : 970 34 956 Date : 2/2007 Version : A This photograph does not necessarily represent the engine N4.85 - Owner s manual Technical characteristics Engine specifications Cycle 4 strokes, Diesel
English N Reference : Date : 12/2007 Version : A. This photograph does not necessarily represent the engine
English N4.00 Reference : 970 34 343 Date : 2/2007 Version : A This photograph does not necessarily represent the engine N4.00 - Owner s manual Technical characteristics Engine specifications Cycle 4 strokes,
4002 Series. Determing the stud length number when using receptacle: Type Type 3. G = P + F (8,9 min.) Release January 2009 G-1
Particular Features Max. tensile strength.00 N. Small-size fastener for high tensile load. Wide variety of conventional stud assembly and receptacle design. Floating receptacles available. Selection Instructions
Volvo - Product Code 100,1,2, 4, 6, 7, 8, 9, 10 & 112
Volvo - Product Code 100,1,2, 4, 6, 7, 8, 9, 10 & 112 Item Description Product_ Code On Hand Qty 20460353 TEMPERATURE SENSOR 100 1 3854260 DISTRIBUTOR 100 1 3854001 COIL 100 1 876839 GASKET KIT 100 1 70326595
5. Keep rotating the water pump housing to release the belt tension and remove the belt once it becomes loose.
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to manufacturer s guidelines. Cold Engine Cold tensioner: 1.
Audi S1 Intake kit. Qty. Description
Audi S1 Intake kit Description Qty Silicone Intake pipe 1 Vacuum hose 1 Heatshield 1 Bracket 1 Machined inlet 1 Vacuum connector 1 Filter 1 M6x16 cap head bolt 1 Tools Ratchet Extension Torx socket Sockets
2015+ WRX/STI RADIATOR SHROUD
2015+ WRX/STI RADIATOR SHROUD Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket performance
NOVA COMFORT & STELLA COMFORT. Assembly manual. Rev
P O O L E N C L O S U R E S NOVA COMFORT & STELLA COMFORT Assembly manual Rev. 2016.1 BOX DISASSEMBLY Model Outside dimensions Weight Name Type Glazing Width Height Depth kg Nova Comfort 3x6 A3 4750 1350
Standardmotoren Standard motors
Standardmotoren Standard motors Contents Product description 2/2 Overview of technical data 2/5 2 Series W4.R for Premium Efficiency IE3 2/6 Series WE.R for High Efficiency IE2 2/14 Series K2.R for Standard
TSI Date Group No. Supp. Page
Volvo Trucks North America, Inc. Greensboro, NC USA This TSI Service Bulletin and others in Groups 21 and 33 replace TSI Service Manual 210 600, Basic Engine, D12, D12A, D12B, D12C (8.2000), publication
IPVP High-pressure Internal Gear Pumps for Variable Speed Drives
IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Design and Function 7 6 5 9 2 5 6 7 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing
Engine, disassembling and
Page 1 of 38 13-1 Engine, disassembling and assembling Lock carrier, moving into service position Special tools and equipment 3369 support tool 1 - Bolts 2 - Bolts 3 - Bolts 4 - Bolts 5 - Bore 45 Nm (33
Cooling Systems FLKS - 3S/1.0/W... FLKS - 3L/1.0/W DESCRIPTION
Cooling Systems FLKS - S/1.0/W... FLKS - L/1.0/W... 1. DESCRIPTION 1.1. APPLICATIONS Cooling circuits: Cooling of AC main drives Cooling of motor spindles on machining centres Cooling of transmission and
Pre-assembled plug connectors Product range overview
Pre-assembled plug s Product range overview Function Electrical connection Type Cable Version Page/Internet Round plug M8, 3-pin SEA-3GS-M8-S Pg7 Straight/ SEA-GS-M8 Pg7 Straight/ solder lug M12, -pin
Modules for fine machining. Guhring modules 6x6 and 4x4. NEW: Module 6x6
NEW: Module 6x6 simple, quick and highly accurate setting of 6-fluted tools minimal tension thanks to 6 setting elements perfect balancing with 6 balancing screws Modules for fine machining Guhring modules
Hukseflux USER MANUAL PMF SERIES. Thermal Sensors. A full range of pyranometer mounting fixtures ACCESSORY
Hukseflux Thermal Sensors ACCESSORY USER MANUAL PMF SERIES A full range of pyranometer mounting fixtures Copyright by Hukseflux manual v1804 www.hukseflux.com info@hukseflux.com Contents Contents 2 Warning
SERVICE INSTRUCTION OIL LEAKAGES IN THE AREA OF THE CYLINDER BARREL FOR ROTAX. SI-912 i-006 R1 SI R3 SI R3
SERVICE INSTRUCTION OIL LEAKAGES IN THE AREA OF THE CYLINDER BARREL FOR ROTAX MOTOR TYPE 912 i, 912 AND 914 (SERIES) d05797 This SI revises SI-912 i-006 Initial issue, SI-912-019 R2 and SI-914-021R2 dated
10. MOULD CLAMPING. 212 Moulding Supplies Edition 9 // POWER CLAMPS 10.2 STANDARD CLAMPS
10. MOULD CLAMPING 213 214 10.1 POWER CLAMPS 10.2 STANDARD CLAMPS 212 Moulding Supplies Edition 9 // www.mouldpro.com POWER CLAMPS POWER SLIDING CLAMP Part No. Thread Size h-min h-max s e1 d sw L e b c
Throttle valve and throttle check valve type CQ, CQR and CQV
Throttle valve and throttle check valve type CQ, CQR and CQV Product documentation Screw-in valve Operating pressure pmax: Flow rate Qmax: 700 bar 50 lpm D 7713 10-2016-1.1 by HAWE Hydraulik SE. The reproduction
Service Bulletin. HIITMill (X) Brake Lever Drift
HIITMill (X) Brake Lever Drift Applies to: HIITMill (9-4590) + HIITMIll X (9-4640) On some HIITMill and HIITMill X units, the brake lever can drift when the user is Rev. A applying load to the belt. This
Installation Instructions
Description The following pages show the steps required to assemble and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation
SHEET DESCRIPTION PAGE NO. NO.
CONTENTS SHEET DESCRIPTION PAGE NO. NO. E-1 CYLINDER BLOCK, LINER AND OIL SUMP 2 E-2 CYLINDER HEAD 6 E-3 PISTON AND CONNECTING ROD ASSY 10 E-4 CRANK SHAFT 12 E-5 TIMING GEAR COVER & SEALING 14 E-6 TIMING
05 COOLING SYSTEM Coolant pump Exchange coolant pump Install coolant pump... 32
SERVICE MANUAL MARINE ENGINES Table of Contents Page 05.00 Functional description cooling circuit... 05.00.0 Raw water circuit (external cooling circuit)... 05.00.0 Closed coolant from cooling circuit
2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
Figure Figure
ENGINE COOLING SYSTEM (CONT D) Water Pump Housing Cover Removal And Installation Remove the seat. Drain the coolant from the radiator. (See Cooling System Pressure Test on Page 50-50-.) Water Pump Disassembly
The Worlds First Tuned Air Intake System
!"#$%&'()*#%+,+-.//01! 2/--3-2%40++54%6'7* -89:%;?%@ABC8%!"#$#%&'('#&)*'+(,,-'+#%&%'#.&* 1-2-1/2 hump hose (#3034) 1-2-3/4 elbow hose (#3173) 2- Power-Band.048 (#4004) 2- Power-Band.040 (#4003) 1- M6
BW0511FP. ByWire Elements BW0511FP Flow Sharing Element Interface IBW0511
ywire Elements Flow Sharing Element Interface IW05 efore use, carefully read the GENERL INSTRUCTIONS FOR USE OF DIRECTIONL CONTROL VLVES Technical data Nominal flow Nominal pressure 35 l/min - P=8 bar
Series PD directly operated solenoid valves
> Series PD solenoid valves CATALOGUE > Release 8.8 Series PD directly operated solenoid valves /-way - Normally Closed (NC) Please note that all Series PD solenoid valves are supplied with direct current
High-pressure switch for gas, air, flue gases and combustion products GW 500 A4 GW A4/2 HP
High-pressure for gas, air, flue gases and combustion products HP /2 HP 5.04 Printed in Germany Rösler Druck Edition 06.04 Nr. 241 654 1 6 Technical description The pressure is an adjustable pressure for
ON-VEHICLE INSPECTION
452 DLC3 CAN VIM Intelligent Tester G035612E02 ON-VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Listen to the throttle control motor operating sounds. (1) Turn the ignition switch to ON. (2) When pressing
ALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 0003 e 00 000 e 00 004 Installation Instructions Mitsubishi Pajero Diesel
Alcoa Fastening Systems. Camloc Quick-Operating Fasteners
Camloc Quick-Operating Fasteners Contents Page General Information... A-2 Important Information... A-3 - A-4 General Installation Instructions for 1/4-Turn Fasteners... A-5 1/4-Turn Fasteners 5F Series...
Mounting on manifold strip. Working pressure min./max. Max. particle size 5 µm. Connector standard ISO 15217
1 00137795 Version Spool valve, zero overlap Sealing principle Soft sealing Mounting on manifold strip P-strip Working pressure min./max. See table below Control pressure See table below min./max. Ambient
ELWOOD HIGH PERFORMANCE MOTORS
SW SERIES WASHDOWN MOTOR DATA: M42X FRAME 115V Drive Supply Motor Data (160VDC Bus) MOTOR MODEL M422 L M423 S M422 L M423 S MECHANICAL DATA (1) Nm 0.62 0.99 0.62 0.99 lb in 5.49 8.81 5.49 8.81 Nm 1.86
Fuel System of Service Manual
Fuel System of Service Manual for H Series Engine for Generator sets October of 2015 1 Table of Contents 13.1 About System... 13-3 13.2 System Diagram... 13-4 13.2.1 Fuel system (4 cylinders)... 13-4 13.2.2
Housing: black plastic Measuring element: copper spring. Protection rate: IP31 Threaded: axial type. Setting: 0 10 bar (0 150 psi)
DESCRIPTION The wide range of FI FILTRI indicators, covers all industrial applications. They are directly installed on the filter, and allow a complete control of the clogging level of the element. This
Level indicators, screw plugs
Level indicators, screw plugs 885 Product overview Level indicators, screw plugs Oil level gauges K0443 Plastic plugs K0452 Oil level gauges K0444 Page 888 Aluminium plugs K0453 Page 894 Oil level sight
SILOXA frame-mounted gas drying system, GK model, set up for outdoor installation
Technical Datasheet 1/5 Condensate trap Moulded piece, material No. 1.4571, for fl ange-mounting on gas cooler DN 150-400 Demister, material No. 1.4571 Condensate outlet via liquid shut-off valve Monitoring
Body, front. Lock carrier with attachments, removing and installing
Page 1 of 19 50-1 Body, front Lock carrier with attachments, removing and installing 1 - Hex bolt (6x) 45 Nm (33 ft lb) 2 - Hex bolt 45 Nm (33 ft lb) 3 - Hex bolt (4x) 10 Nm (7 ft lb) 4 - Hex bolts (2x)
Cooling system components, removing and installing
19-1 Cooling system components, removing and installing Note: When the engine is warm the cooling system is under pressure. If necessary release pressure before starting repair work. Hoses are secured
ContiTech: Expert Tips for Changing Timing Belts
ContiTech: Expert Tips for Changing Timing Belts Detailed instructions for a CT1015 WP1 and CT1018K1 in an Audi A4 (B6) 2.5-liter V6 TDI with engine code AKE MY 2001 ContiTech shows how to avoid errors
IE MK5 & MK6 Downpipe Install Guide IEEXCC5
IE MK5 & MK6 Downpipe Install Guide IEEXCC5 Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation of IE s 3 Downpipe System for VW
Removing and installing toothed belt
Page 1 of 10 Special tools and workshop equipment required Diesel injection pump locking pin -3359- (2x) Pin wrench -T10020- Crankshaft stop -T10050- for engines with circular crankshaft sprocket Locking
Series PD directly operated solenoid valves
> Series PD solenoid valves CATALOGUE > Release 8.7 Series PD directly operated solenoid valves New /-way Normally Closed (NC) Note: all Series PD /-way solenoid valves are basically in DC. To operate
Threaded fittings. Festo core product range Covers 80% of your automation tasks
q/w Worldwide: Superb: Easy: Festo core product range Covers 80% of your automation tasks Always in stock Festo quality at an attractive price Reduces procurement and storing complexity qgenerally ready
Duct filter units. Duct HEPA filter units AKF
Duct HEPA filter units AKF Application Duct HEPA filter unit AKF is being used in the network of inlet and outlet ducts used to supply or extract air from the rooms with highest demands regarding air cleanness.
CYLINDER HEAD. Cylinder Head Assembly. Sized for Print VALVES
CYLINDER HEAD Cylinder Head Assembly VALVES DISASSEMBLY 1. Using a tool remove the cylinder head bolts in the order shown in the illustration. 2. Using the special tool (09222-28000, 09222-28100), remove
Technote. Frese YDF-2F & YDF-20F - differential pressure control valve. Application. Benefits. Features.
Page 1 of 5 Application Frese YDF-2F and YDF-20F differential pressure control valves are used in central heating-, ventilation-, and district heating systems This model is a high-performing adjustable
SERVICE INSTRUCTIONS Air Motor
SERVICE INSTRUCTIONS Air Motor 338905 DESCRIPTION The air motor has a 3" diameter piston with a -5/8" stroke. When the pump-tube upper packing is not incorporated into the air motor, the air motor is considered
Directional valves Mechanically operated Series CD07. Brochure
Series CD07 InduParts Pneumatics B.V.B.A. Sint-Jorisstraat 40 B-8800 ROESELARE BELGIUM Tel. + (0)5 58 88 Fax. + (0)5 58 98 info@induparts.com www.induparts.com Brochure Bosch Rexroth AG Pneumatics Series
Type and Type Pneumatic Control Valves Type 3510 Micro-flow Valve
Type 3510-1 and Type 3510-7 Pneumatic Control Valves Type 3510 Micro-flow Valve ANSI version Application Control valve especially designed for controlling low flow rates in pilot plants and technical research
Magnetic and Hydraulic-Magnetic Circuit Breaker 8340-G V
Description Single and two pole magnetic circuit breakers with trip-free mechanism and push/pull on/off manual actuation. A choice of fast magnetic only or hydraulically delayed switching characteristics
Standards ISO Max. particle size 50 µm. Pressure for determining piston forces. Materials: Polyurethane
Ports: - double-acting with magnetic piston Cushioning: elastic Piston rod: external thread 1 Standards ISO 21287 Compressed air connection Internal thread Working pressure min./max. 1 bar / 10 bar Ambient
2007 Ford Freestyle SEL
Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold
Replacing the timing belt
"VCC116740 EN 20091209" 1(5) Replacing the timing belt Special tools: 999 5433, 999 5456 Removing the timing belt Note! As the illustrations in this service information are used for different model years
Brass Compression Fitting Range
Compression Fitting Range Fittings Stud Fittings 0105 BSPT Page 5-9 0105 NPT Page 5-9 0101 BSPP/Metric Page 5-10 0101..39 BSPP Page 5-10 0101 Metric Page 5-11 01 BSPP Page 5-11 0109 BSPT Page 5-12 0109
RoFLEX - HIGH PRESSURE - SCREW COUPLINGS
Edition E 01/2013 DAT Copyright 2014 by Swiss Technology RoFLEX - HIGH PRESSURE - SCREW COUPLINGS - connectable and disconnectable under full pressure - Part "A" (Aussengewinde) Part "S" (Sechskantmutter)
Instruction Manual P/N: Make: Honda Model: Accord Year: Engine: L4-2.4L
Instruction Manual P/N: 12559006 Make: Honda Model: Accord Year: 2008-2012 Engine: L4-2.4L Please read the entire instruction manual before proceeding. Ensure all components listed are present. If you
Number of fingers 2. Max. particle size 5 µm. Pressure for determining forces
Bosch Rexroth AG Pneumatics Version Parallel Number of fingers 2 Grip tolerance 0,02 mm Lubrication gripping elements Lubricated for life 00117208 Ambient temperature min./max. +5 C / +60 C Medium Compressed
SPAREPARTSCATALOG: // ENGINE 390 DUKE 2015 ART.-NR.: 3CM081270OEN
SPAREPARTSCATALOG: // ENGINE ART.-NR.: 3CM08270OEN CONTENT ENGINE CASE CLUTCH COVER 3 CRANKSHAFT, PISTON BALANCER SHAFT 4 CLUTCH 7 SHIFTING MECHANISM 5 TRANSMISSION I - MAIN SHAFT 8 WATER PUMP CYLINDER
Trouble in Passenger Airbag ON / OFF Indicator
8 SUPPLEMENTAL RESTRAINT SYSTEM OCCUPANT CLASSIFICATION SYSTEM Trouble in Passenger Airbag ON / OFF Indicator DESCRIPTION The occupant classification system detects the front passenger seat condition and
MK 10-9V - PL 10 7, MK 10-13V - PL REF d1 d2 d3 d4 L L1 P (bar) T ( C)
Euro MK10-PL Quick Release coupling straight with valve Push-to-Lock, O-ring: Viton REF d1 d2 d3 d4 L L1 P (bar) T ( C) MK 10-9V - PL 10 7,5 17 9 54 24 15 200 MK 10-13V - PL 13 10 23 13 64 28 10 200 MK15-PL
Holistic Method of Thermal Management Development Illustrated by the Example of the Traction Battery for an Electric Vehicle
20 th Aachen Colloquium Automobile and Engine Technology 10 th 12 th October 2011 Holistic Method of Thermal Management Development Illustrated by the Example of the Traction Battery for an Electric Vehicle
* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION *
XDP Duramax LBZ EGR Race Track Kit Item Number: XD165 PACKING LIST: 1 LBZ EGR Plate for Up Pipe 5 M8x1.25-20mm Bolt 2 M10x1.5 Flange Hex Nut 1 LBZ EGR Plate for Intake 1 M8x1.25-45mm Bolt 1 M8x1.25 Flange
Rotary vane vacuum pump(dry-running) Type T 4.4 T T V T /400V TS V
Operation Manual Rotary vane vacuum pump(dry-running) Type T 4.4 T 4.500 TF 4.4-24V TF 4.6-24V T 4.4-230V T 4.4-230/400V T 4.8-230V T4.8-230/400V T 4.8-500V T4.16-230/400V TS4.16-230V T 4.16-230V TS4.16-230/400V
Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13)
13 Engine-Crankshaft, Cylinder block (Page GR-13) Engine, disassembly and assembly 10-222 A/21 guide from 10-222 A support tool, modifying Ribbed belt, removing and installing Semi-automatic toothed belt
Bill of Materials for
Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1
For applications with high axial play. For applications with reduced mounting space
Fig. Example of use Use : Pitch circle diameter Suitable for encoders Page high axial play 8.000.4K00.0000 cylindrical pin Long spring element 0 mm A020, A02H 9080, 908 262 reduced mounting space 8.000.4J00.0000
NR Rack Installation Guide
Technical Data Sheet Doc no; NR Rack Installation Guide Page 1 TABLE OF CONTENTS SECTION SAFETY WARNINGS 1 600 WIDE EXPLODED VIEW 2 800 WIDE EXPLODED VIEW 3 SWITCHING DOOR HANDING 4 STABILIZING 5 BAYING
Built-in motors. Contents. Product description 7/2 Overview of technical data 7/3
Built-in motors Contents Product description 7/2 Overview of technical data 7/3 Motor selection data Series W4.R (corresponds to Efficiency IE3) 7/4 Series WE.R (corresponds to High Efficiency IE2) 7/6
PA-S small filter. Technical Data G 1/8
PA-S small filter PA-S small filter G 1/8 Bowl material Polyamid Head material Polypropylene Gasket material Buna-N Filter material PE 5µm, 35µm or 80µm Temperature Min./Max. C 5-50 Maximum pressure bar
TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
22K (red red orange gold) 1pcs. 33K (orange orange orange gold) 5pc. 2.7 M (green violet red gold) 2pc.
TURNING FROG Long pliers, soldering, soldering iron stand with sponge, 2 AA batteries, one 9V battery, Tin, diagonal cutting pliers Turning Frog is a robot that uses a microphone as a detector. When microphone
A/C compressor brackets
Page 1 of 8 87-76 A/C compressor brackets A/C compressor bracket (4-cyl. engine), removing and installing - Remove front noise insulation panel under engine, detach complete front bumper/grille assembly
Pressure regulators E/P pressure regulators Series ED05. Brochure
Series ED05 Brochure Series ED05 Qn= 000 l/min Compressed air connection output: G /4 Electr. connection: via signal connection Signal connection: input and output, Plug, M, 5-pin 4 Qn= 000 l/min Compressed
PIERBURG. Carburetor: 2E3
PIERBURG Carburetor: 2E3 1 fast idle adjusting screw 2 throttle lever 3 fuel mixture adjusting screw 4 main body 5 idle cut off valve 6 stop screw 7 accelerator pump cover 8 diaphragm 9 spring 10 valve
Compression Fittings. Brass Compression Fittings. Stainless Steel Compression Fittings. PL Nickel-Plated Brass Spigot Fittings
Compression Fittings Compression Fittings Stainless Steel Compression Fittings PL Nickel-Plated Spigot Fittings Compression Fittings Compression Fittings Compression Fittings (P. 5-5) Stainless Steel Compression
Types 1808 and 1808A Pilot-Operated Relief Valves or Backpressure Regulators
Instruction Manual Form 5116 Types 1808 and 1808A July 2010 Types 1808 and 1808A Pilot-Operated Relief Valves or Backpressure Regulators! Warning Failure to follow these instructions or to properly install
Eliminator Vented Disc Brakes Owners Manual
Eliminator Vented Disc Brakes Owners Manual TIE DOWN ENGINEERING 255 Villanova Drive SW, Atlanta, GA 30336 www.tiedown.com (404) 344-0000 Fax (404) 349-0401 Instruction Sheet #08075 101310,C752 Eliminator
REMOVAL AND INSTALLATION
303-08-1 Engine Emission Control 303-08-1 REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Cooler 6.4L Diesel, Vertical Cooler Item Part Number Description 1 Fuel cooler tube 2 W701317 Power steering
AL-KO SIDE LIFT JACK HANDBOOK FOR THE 800KG SIDE LIFT JACK FOR CARAVANS WITH A MAXIMUM GROSS WEIGHT OF 1600KG
AL-KO SIDE LIFT JACK HANDBOOK FOR THE 800KG SIDE LIFT JACK FOR CARAVANS WITH A MAXIMUM GROSS WEIGHT OF 1600KG CONTENTS 3 WARNINGS & TECHNICAL INFORMATION 4 FITMENT OF JACK BRACKETS 7 OPERATING INSTRUCTIONS
WINCH MOUNT KIT FOR YAMAHA VIKING P/N ASSEMBLY / OWNERS MANUAL. Application WINCH KIT NO. 25-9xxx
WINCH MOUNT KIT FOR YAMAHA VIKING P/N 25-5270 ASSEMBLY / OWNERS MANUAL Application WINCH KIT NO. 25-9xxx Before you begin, please read these instructions and check to be sure all parts and tools are accounted
BHW Engine Coolant Temperature Replacement
BHW Engine Coolant Temperature Replacement NEVER perform this procedure on a hot engine. Parts: 059 919 501 A dual temperature sensor 032 121 142 retaining spring N 903 168 02 sensor round seal N 905 216
Anti-lock Brake System (ABS),
Page 1 of 12 45-6 Anti-lock Brake System (ABS), Bosch 5.0 CAUTION! The anti-lock brake system is basically maintenance-free. Specialist knowledge is required for performing any work on this system. Failure
Toothed belt, removing and installing
Toothed belt, removing and installing Special Tools and Equipment ^ 3212 spanner wrench ^ 3387 pin wrench ^ T40011 pin ^ T40026 locking pin ^ T40028 socket ^ T40030 camshaft adjuster gauge Removing Lock
The GK units differ from the LK units in that the springs of the GK units have a spring eye at the front.
01 09 Installation guidelines Mechanical suspension units GK LK GN0032-0 Mechanical suspension units GK LK The GK units differ from the LK units in that the springs of the GK units have a spring eye at