* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION *
|
|
- Gervase Fields
- 5 years ago
- Views:
Transcription
1 XDP Duramax LBZ EGR Race Track Kit Item Number: XD165 PACKING LIST: 1 LBZ EGR Plate for Up Pipe 5 M8x mm Bolt 2 M10x1.5 Flange Hex Nut 1 LBZ EGR Plate for Intake 1 M8x mm Bolt 1 M8x1.25 Flange Hex Nut 1 - EGR blocker support plate 1 M10x mm Bolt 3 EGR Gaskets 1 Standoff A 2 - M6x1.0-25mm Bolts 1 20" 5/8" Heater Hose 1 Standoff B 1 M10x1.5-80mm Stud 2 5/8" Hose Clamps 1 Standoff C 1 M10x1.5-95mm Stud Before removing any parts from your truck, please compare the items you have received with the packing list provided to verify that you have everything necessary to install your XDP Duramax LBZ EGR Race Track Kit. WARNING: This high performance product is intended SOLELY for closed-course racing use and is not street legal in ANY state. This product cannot be used on any vehicle that is registered or certified for highway use. *Aftermarket Tuning Required* Ensure that the vehicle has not been in use and that the engine is cool to the touch. Always wear eye protection when working on any vehicle. * PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION * XDP Duramax LBZ EGR Race Track Kit (XD165) Page 1
2 XDP Duramax LBZ EGR Race Track Kit Step 1: Disconnect negative battery cables. Step 2: Remove passenger side inner fender. Step 3: Remove coolant tank cap. Step 4: Locate the lower radiator hose on the passenger side of the radiator. Step 5: Remove the butterfly clip. Step 6: Place a drain pan under the passenger side of the radiator. Step 7: Gently pull the radiator hose back to drain. (The coolant will drain quickly.) Intake Tube Step 8: Remove the resonator and intake tube. Step 9: Remove the (3) wiring harness retaining bolts on top of the intake bridge using a T30 tork drive. Step 10: Remove the (2) bolts retaining the cast aluminum CAC pipe. Bolt 1 Resonator Bolt 2 XDP Duramax LBZ EGR Race Track Kit (XD165) Page 2
3 Step 11: Remove the bolt retaining the dipstick tube. Step 12: Remove the ignition wire for the intake air heater. Step 13: Disconnect the MAF sensor connector. Step 14: Remove the EGR actuator connector on the passenger side of the truck. XDP Duramax LBZ EGR Race Track Kit (XD165) Page 3
4 Step 15: Remove the butterfly clip retaining the cast aluminum CAC pipe and the plastic CAC pipe together. Step 16: Remove the wiring harness bracket connected to the stud on the intake horn by removing the nut with a 12mm socket. Step 17: Gently pull the wiring harness towards the front of the truck. Step 18: Remove the bolt holding down the PCV hose to the valve cover on the passenger side of the motor with a 10mm socket. XDP Duramax LBZ EGR Race Track Kit (XD165) Page 4
5 Step 19: Use needle nose pliers to remove the spring clamp on the turbo intake. Lay the PCV hoses over to the driver side of the truck. Step 20: Remove the turbo vane actuator solenoid connector and set aside. Step 21: Loosen the band clamp on the turbo intake mouthpiece and remove XDP Duramax LBZ EGR Race Track Kit (XD165) Page 5
6 Step 22: Remove the (4) bolts retaining the intake bridge. Set the intake bridge aside. Step 23: Remove the heater core coolant hose that is closest to the driver side of the truck. Step 24: Remove the two nuts retaining the EGR cooler to the uppipe. Nuts are removed from the back of this flange Step 25: Remove the two bolts retaining the EGR cooler to the EGR cooler bracket. Bolts retain the cooler in this bracket XDP Duramax LBZ EGR Race Track Kit (XD165) Page 6
7 Step 26: Using a 14mm socket remove the two bolts on the front of the EGR cooler and remove the cooler. Step 27: Clean the up-pipe sealing surface to ensure a proper seal. Step 28: Install the up -pipe blocker plate and gasket. Use one M8x mm bolt for the upper blocker plate hole, and use the M8x mm bolt for the lower blocker plate bolt. (Make sure you tighten these two bolts before moving to the next step) Step 29: Remove the two bolts on the EGR bracket that are retaining the heat shield above the Rail Pressure Sensor. Step 30: Install the EGR blocker support plate provided with your kit using the two M6x1.0-25mm bolts. Step31: Finger tighten the M8x1.25 nut onto the M8x mm bolt and the M10 bolt that retains the up -pipe blocker plate to the EGR cooler bracket. Once both installed they can then be tightened each with a wrench. Step 32: Install the heater hose on the two open coolant ports and secure with supplied hose clamps. Step 28 Step 29 Photo shows an LMM plate Step 30 XDP Duramax LBZ EGR Race Track Kit (XD165) Page 7
8 Step 33: Set standoff A in the mounting location of the EGR actuator closest to the alternator. Step 34: Set the wiring harness ring terminal on top of standoff A. Step 35: Install the 95mm stud through the wiring harness ring terminal and standoff A. Step 36: Install standoff B on the 90mm stud. Step 37: Install the 80mm stud in the outer most bolt hole that previously retained the EGR motor. Step 38: Install standoff C on this stud. Standoff A Standoff C Standoff B Wiring harness ring terminal Step 39: Install the intake bridge bracket with the long straight edge toward the front of the truck and the laser engraving facing down. Step 40: Retain the intake bridge with the two M10 flange head nuts. (Do not tighten the flange head nuts yet.) Step 41: Clean the sealing surface of the intake bridge. Step 42: Lay the intake bridge gaskets in their appropriate location on the intake bridge support plate. Step 43: Install the intake bridge on the intake horn and support plate. Fasten the intake bridge to the support plate using (4) M8x mm flange head bolts and use factory fasteners to refasten the intake bridge to the intake horn. Step 44: Tighten the two M10 flange head nuts on the studs. XDP Duramax LBZ EGR Race Track Kit (XD165) Page 8
9 Step 45: Reinstall the cast aluminum CAC pipe and retaining bolts. Step 46: Reinstall the turbo intake mouthpiece. Do not tighten. Step 47: Reinstall the PCV on the passenger side valve cover and into the intake mouthpiece. Step 48: Reinstall the turbo vane actuator solenoid connector. Step 49: Reinstall the intake pipe from the mouthpiece to the air filter box. Tighten both ends then tighten the mouthpiece. Step 50: Reinstall the resonator and PCV tube. Step 51: Ensure the radiator drain plug is closed and refill the cooling system with coolant. Step 52: Connect the battery cables. Step 53: Start the truck and check for leaks. Step 54: Drive the truck to further check for coolant leaks and check for drive pressure leaks. (A drive pressure leak will create a squealing sound.) PLEASE CONTACT XDP ( ) FOR TECHNICAL ASSISTANCE XDP Duramax LBZ EGR Race Track Kit (XD165) Page 9
Duramax LMM EGR Delete With Intake Tube
Duramax LMM EGR Delete With Intake Tube PACKING LIST: QTY. 4 2 2 2 Description Intake Charge Pipe w/ O-Ring M8 Flange Nut M8x25 Flange Hex Bolt M0x20 Hex Head Bolts M8x25 Socket Head Bolts M8x20 Hex Head
More informationDURAMAX LMM EGR DELETE
007.5-010 DURAMAX LMM EGR DELETE Duramax LMM EGR Delete B K I J F D G H A C PACKING LIST: E Part # A B C D E F G H I J K QTY. 1 1 1 1 Description Billet Intake Block Off Plate with O-ring Exhaust Block
More informationL DURAMAX LBZ EGR DELETE GDP TUNING
2006-2007.5 6.6L DURAMAX LBZ EGR DELETE GDP TUNING ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the be used on vehicles that are operated
More informationIncluded: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware -
Included: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware - Nuts, Bolts, & Washers 2. Hose Clamps 1. Support Bracket
More informationXDP Complete EGR Race Track Kit w/up-pipe. Item Number: XD144
XDP Complete EGR Race Track Kit w/up-pipe Item Number: XD144 PACKING LIST: 2 - Lined 3/4" SS Hose Clamp 1-3/4 Silicone Hose 1 - XDP Engraved EGR Valve Block-Off Plate with O-ring 1 - EGR Cooler Block-Off
More informationIncludes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts
Includes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts WARNING: This product is not legal for sale or use on pollution controlled
More informationDURAMAX LBZ EGR DELETE
006-007.5 DURAMAX LBZ EGR DELETE ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing
More informationIncludes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses
Includes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses CAUTION: Never work on a hot vehicle. The hot exhaust system or hot engine can cause serious injury in the form of burns. If the vehicle has
More informationDURAMAX LML EGR DELETE
2011-2012 DURAMAX LML EGR DELETE Sinister Diesel EGR Delete Kit A B C D E F G H PACKING LIST: QTY. A B C D E F G H QTY. 1 4 1 1 1 3 1 4 Description Blue Coolant Hose M8 x 25 Hex Head Bolts Exhaust Block
More information* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION
XDP 6.0L Complete EGR Delete Kit w/up-pipe Item Number: XD169 PACKING LIST: 2 - Lined 3/4" Hose Clamps, 1-180 Coolant Tube, 1-3/4 Silicone Hose, 1 - Stainless Steel Up-pipe 1 - EGR Valve Block-Off Plate,
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More information2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
More informationIncludes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps
Includes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps WARNING: This product is not legal for sale or use on pollution controlled vehicles
More informationIncludes: 1. High Flow Turbo Up-Pipe 1. J-Hook Block Off / Coolant Reroute 1. Coolant Hose 1. EGR Valve Block Off Plate 2. Hose Clamps 4.
Includes: 1. High Flow Turbo Up-Pipe 1. J-Hook Block Off / Coolant Reroute 1. Coolant Hose 1. EGR Valve Block Off Plate 2. Hose Clamps 4. Bolts & Nuts WARNING: This product is not legal for sale or use
More information4 December 2017 PN# , , Dodge 6.7L Rumble B SXE (I-00400) 1. BD Rumble B SXE. D o d g e 6. 7 L H P C R Installation Instructions
4 December 2017 PN#1045705, 1045706, 1045708 Dodge 6.7L Rumble B SXE (I-00400) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Rumble B SXE D o d g e 6. 7 L H P C R Installation Instructions
More informationBD TrackMaster S D o d g e H P C R Installation Instructions
7 July 2016 PN#1045701, 1045702, 1045704 Dodge 6.7L TMS400 (I-00361) 1 BD TrackMaster S400 2008-2012 D o d g e H P C R Installation Instructions 1045701 2008-2009 Dodge 6.7L TMS400 1045702 2010-2012 Dodge
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationLML 3 Y-Bridge Kit or High Flow Intake Bundle Package
2011-2016 LML 3 Y-Bridge Kit or High Flow Intake Bundle Package Covers installation of PN s: WCF100607, WCF100691, WCF100716, & WCF100353 Note: This Kit is for off road competition use only! Overview-
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
28 January 2014 1045140 6.7L Super B Special Turbo Installation (I-00266) 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
26 September 2012 1045140 6.7L Super B Special Turbo Installation 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140 PLEASE
More informationHR ZDX Throttle Body Install (06-11 Civic Si)
HR ZDX Throttle Body Install (06-11 Civic Si) This guide will walk you through the steps to install a ZDX throttle body onto your RBC Intake manifold using the Hybrid Racing ZDX adapter. Written By: Hybrid
More informationIndustrial Injections Compound Turbo Installation For 6.7L Scorpion
Industrial Injections Compound Turbo Installation For 6.7L Scorpion Step 1: Whenever you are doing an installation the first thing you should do is unhook the batteries to avoid arcing. You will need an
More information3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B
3 October 2016 PN#1045320 24V Dodge Twin Turbo Kit (I-00274) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Twin Turbo Kit 1998½- 2 0 0 2 D o d g e 2 4 v I S B Part# 1045320 PLEASE READ
More informationInstallation Instructions
2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com
More informationDodge 6.7L
22 March 2016 2007-2010 6.7L Dodge Cummins (I-00014) 1 A Tuner capable of eliminating DTC codes, must be used with this kit. EXHAUST GAS BLOCKER KIT 2007-2016 Dodge 6.7L Part #: 1090011 Part #: 1090012
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationPowerstroke 6.4L EGR Block Kit
Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** You will need the following tools for this installation: 10mm wrench 13mm wrench
More informationStep 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More informationFord 6.7 EGR Delete Kit
Fits: 2011 12 Powerstroke 6.7L Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** ***This kit is intended for off road use only.***
More informationINSTALL MANUAL D o d g e 1 2 v 6 B T A PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.
PN#1045310 12V Dodge Twin Turbo Kit (I-00273) 1 INSTALL MANUAL BD Twin Turbo Kit 1994-1 9 9 8 D o d g e 1 2 v 6 B T A Part# 1045310 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. * Picture as shown
More informationInstallation Instructions
BD DODGE CUMMINS PERFORMANCE E X H A U S T M A N I F O L D Installation Instructions Application List 2007-2015 6.7L / HE351 OE Turbo 1045965 2007-2015 6.7L / T4 S400 Turbo s 1045965-T4 PLEASE READ ALL
More informationFord Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours
Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen
More informationForbidden Diesel Performance Ford 6.7L Powerstroke EGR Delete Instructions 6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE. Page 1
6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE Page 1 WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More informationInstallation Manual v1.1: Piece Pulse Flow Exhaust Manifold, Stock Replacement L Cummins
Installation Manual v1.1: 204-927-2326 2-Piece Pulse Flow Exhaust Manifold, Stock Replacement 2007.5-2016 6.7L Cummins Please read all instructions before installation. We suggest purchasing new gaskets
More informationInstallation Instructions
Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor
More informationASSEMBLY/INSTALLATION INSTRUCTIONS
ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath
More informationInstallation Instructions PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
1 GMC/CHEVY LMM DURAMAX (2007.5-10) FOR 2500 & 3500 SERIES PICKUPS V A R I A B L E V A N E E X H A U S T B R A K E Installation Instructions P/N# 2001030 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
More informationP/N# Application Description Ford 6.0L Turbo Kit Only w/sct Tuner Ford 6.0L Turbo Kit Only (No drivability guarantee)
1 Low stall convertors are not recommended for this turbocharger kit. BD FORD 6.0L TURBOCHARGER KIT P/N# Application Description 1047070 2003-07 Ford 6.0L Turbo Kit Only w/sct Tuner 1047071 2003-07 Ford
More information6.4L EGR Delete With Intake Elbow
6.4L EGR Delete With Intake Elbow J I E C B F D G H A Part# A B C D E F G H I J PACKING LIST: QTY. 2 4 2 4 2 Description Exhaust Block-Off Plate Exhaust Gasket Coolant Line Plugs Brass Barbed Hose Connector
More information05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
More informationPage 6 of 6 OUTLAW DIESEL EGR COOLER DELETE KIT W/INTAKE ELBOW L FORD POWERSTROKE
What s in the box 1 Exhaust Block-Off Plate 1 Exhaust Gasket 2 Coolant Line Plugs 1 Brass Barbed Hose Connector 1 Stand-off Spacer 4 M10-1.25 x 40 Hex Head Bolts (Exhaust Manifold) 2 M10-1.25 x 20 Hex
More informationH F G I. A (1) Reducer. pg.2
301009 B A D C E H F G I J L M A (1) Reducer B (1) Coolant hose C (1)Block off bracket D (3) Clamps E (1) Cooler side block off plate F (1) Turbo manifold block off plate G (1) Intake manifold side blocker
More information* Optional ( ) Instruction Manual P/N: Make: Infiniti Model: G37 Year: Engine: V6-3.7L
* Optional (12529002) Instruction Manual P/N: 12529001 Make: Infiniti Model: G37 Year: 2008-2011 Engine: V6-3.7L Please read the entire instruction manual before proceeding. Ensure all components listed
More informationCHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic
More informationINSTALLATION GUIDE: EGR Delete Kit Ford 6.7L Powerstroke`
INSTALLATION GUIDE: EGR Delete Kit 20 203 Ford 6.7L Powerstroke` ! Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing
More informationPowerMax Diesel Upgrade For Cummins Engines
PowerMax Diesel Upgrade For Cummins Engines 00.5-007.5 Dodge Ram With Cummins 5.9L Item 3 4 5 6 7 8 9 0 3 4 5 6 7 8 Parts List Description Turbocharger Ancillary kit 773069- (includes) Installation Instructions
More informationThis information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA EGR Valve, Replacement DService Bulletin Trucks Date Group No. Page 11.2006 254 24 1(17) EGR Valve Replacement D16F W2005772 This information covers the proper
More informationDodge 5.9L Cummins 24v ISBe
15 December 2011 Part # 1045160 Killer B Dodge 2003-07 - 1 - BD Killer B Single Turbo 2003-2007 Dodge 5.9L Cummins 24v ISBe Part #1045160 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. UNLESS AN EO#
More informationREMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
More informationCUSTOM-DIESEL.COM ATTENTION VERY IMPORTANT - PLEASE READ
ATTENTION VERY IMPORTANT - PLEASE READ IF YOU PURCHASED THIS ITEM FROM EBAY, WE WANT YOU TO KNOW THAT EBAY HAS ALWAYS GIVEN YOU, THE BUYER, THE STRENGTH TO VOICE YOUR OPINION OF EBAY SELLERS BY LEAVING
More information6.7L Cummins EGR Delete
6.7L Cummins EGR Delete H I A B E C D F J K G L PACKING LIST: Part# A B C D E F G H I J K L QTY. 4 Description Coolant Hose Coolant Hose Connector M0 Flange Nut 5/6 Bolts, Nuts, and Flat Washers /4-0 Bolt,
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationAll cores due 30 days after invoice date - no credit after 60 days.
NO WARRANTY STATEMENT High performance parts & products no warranty policy: The purchaser understands and recognizes that high performance diesel products and services sold by INDUSTRIAL INJECTION SERVICE.
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationPlease call us at Mon-Fri 8am-5pm if you need any additional assistance.
TM Upgraded 6.0L EGR Cooler R Thank you for purchasing a Sinister Diesel Upgraded EGR Cooler. This EGR cooler is designed to endure years of heavy use.these installation instructions have been written
More informationPart number SP Honda Fit cyl. Converts into a short ram
Part number SP1512 2009 Honda Fit 1.5 4 cyl. Converts into a short ram 1- Three piece cold air intake 1-2.75 Injen/AMSOIL (#1010) Ea nano-fiber dry filter 1 2.50 straight hose (#3048) 1- Two bend silicone
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More informationSLP Camaro ZL1 STAGE 3 (650 HP)
SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
More informationEGR Cooler Delete Kit
EGR Cooler Delete Kit 2008-2010 6.4 Liter Ford ATTENTION!!!! The Street Diesel Performance Egr Cooler Delete System kits are designed to be used in conjunction with proper tuning and supporting hardware
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located
More informationDISCLAIMER 1) By installing this product onto your vehicle, you assume all risk and liability associated with its use.
WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing vehicles and cannot be used on
More informationBD SUPER B SINGLE TURBO KIT Dodge 5.9L Cummins v ISBe (Non 600 motors)
1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD SUPER B SINGLE TURBO KIT Dodge 5.9L Cummins 2003-2004 24v ISBe (Non 600 motors) Part # 1045230 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
More informationREMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.
EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,
More informationApplication List L Cummins
1 Discharging & Recharging of the A/C System is required for this install. INTERCOOLER INSTALLATION FOR 2010+ DODGE 6.7L CUMMINS Application List 2010+ 6.7L Cummins 1042530 PLEASE READ ALL INSTRUCTIONS
More informationPart number SP Honda Element 2.4L, 4 cyl.
Part number SP1727 07-08 Honda Element 2.4L, 4 cyl. 1-2 piece cold air intake 1-3 Injen filter (#1017) 1-2.75 straight hose (#3043) 1-3 straight hose (#3044) 1-12 8mm vacuum hose (#3091) 2- Power Bands.312.040
More informationGM 6.6L DURAMAX LLY EGR DELETE
2004.5-2005 GM 6.6L DURAMAX LLY EGR DELETE ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationREMOVAL AND INSTALLATION
303-08-1 Engine Emission Control 303-08-1 REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Cooler 6.4L Diesel, Vertical Cooler Item Part Number Description 1 Fuel cooler tube 2 W701317 Power steering
More informationTABLE OF CONTENTS PARTS LIST
TROUBLESHOOTING: Note: You will have a check engine light and/or other problems unless using this product with a compatible ECM calibration. H&S Motorsports provides compatible calibrations for H&S Performance
More informationINSTALLATION MANUAL
315000 INSTALLATION MANUAL EGR & Cooler Race Kit for 2015+ 6.7L Ford Powerstroke WARNING ONLY install this kit if you are using a tuner that disables the EGR sensors & circuit system. Any product that
More informationBD Twin Turbo Cobra Kit
14 September 2017 1045780-94 Dodge Cobra Kit (I-00377) 1 BD Twin Turbo Cobra Kit 2003-2012 Dodge HPCR Machined BD turbochargers only BUILDERS KIT Installation reccomendations to aid asssembly Does not
More information4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
More informationCOBB Tuning MAZDASPEED6 SF Intake System. Install Instructions
781500 COBB Tuning MAZDASPEED6 SF Intake System Install Instructions Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions will assist you through your installation
More informationThis information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
More informationInstallation Instructions Camaro ZL1 ( Z) ( ZB)
Installation Instructions Camaro ZL1 (501-1099-10-Z) (501-1099-10-ZB) Parts List 1 Insulated Air Box \ Lid 1 Thermal Coated Intake Tube / MAF Housing with (2) M4 x.7 thread 8mm long Stainless Screws; 1
More informationINSTALLATION GUIDE: EGR Delete Kit Chevy 6.6L Duramax
INSTALLATION GUIDE: EGR Delete Kit 004.5 005 Chevy 6.6L Duramax ! WARNING: EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for
More informationPart # 6695S. Read all instructions carefully before attempting installation.
Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions and Warranty Information 2007-10 5.4 Ford Mustang Shelby
More information2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions
Page1 James Barone Racing Aftermarket Parts and Accessories 2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2008-105 FORD 6.4 LITER DIESEL F-SERIES VERSION 3/10 Parts Blackbird Wiring Manual Installation Supplement 6.4 liter Diesel Owner s Manual Includes Warrantee Registration
More informationDOWNLOAD ENHANCED INSTALL MANUALS
U 3 October 2016 1041564 6.7L Performance Intake Plate Manual (I-00371) 1 DOWNLOAD ENHANCED INSTALL MANUALS Cummins 6.7L High Flow Intake Plenum Cover 1041564 2008-2016 6.7L RAM 2500-3500 Pickup PLEASE
More informationL CUMMINS COOLANT FILTER KIT
07.5-12 6.7L CUMMINS COOLANT FILTER KIT ! DISCLAIMER 1) By installing this product onto your vehicle, you assume all risk and liability associated with its use. 2) It is your responsibility to make sure
More informationX Flow Intake Manifold For Dodge 5.9L Cummins Trucks
21 September 2012 1998-02 Dodge Intake Manifold 1041550 & 1041550P - 1 - X Flow Intake Manifold For 1998-02 Dodge 5.9L Cummins Trucks Part # Description 1041550 Intake Horn (Black Powder Coat) 1041550-P
More informationINSTALLATION INSTRUCTIONS MAZDA ROTARY FUEL RAILS
INSTALLATION INSTRUCTIONS MAZDA ROTARY FUEL RAILS ENGINES:,, Document: 19-0195 Support: info@radiumauto.com For Engines follow "" below For Engines follow "" below For Engines follow "" below STEP TOOLS
More informationOwner smanual. Banks Monster-Ram Intake and Grid Heater Delete Kit. For Racing Only Ram 6.7L Pickup Trucks. with Installation Instructions
with Installation Instructions Owner smanual Banks Monster-Ram Intake and Grid Heater Delete Kit For Racing Only 2007-2017 Ram 6.7L Pickup Trucks THIS MANUAL IS FOR USE WITH SYSTEM 42788, 42788-PC, 42790,
More informationBHW Engine Coolant Temperature Replacement
BHW Engine Coolant Temperature Replacement NEVER perform this procedure on a hot engine. Parts: 059 919 501 A dual temperature sensor 032 121 142 retaining spring N 903 168 02 sensor round seal N 905 216
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationGHG14 DD15 Asymmetrical Turbocharger May Removal of the GHG14 DD15 Asymmetrical Turbocharger
5 31-13 1 5 31-13 SUBJECT DATE GHG14 DD15 Asymmetrical Turbocharger May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the GHG14 DD15 Asymmetrical
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More informationINSTALLATION INSTRUCTIONS Dual Catch Can Kit Subaru Turbo and STi Document# Support:
INSTALLATION INSTRUCTIONS Dual Catch Can Kit 02-14 Subaru Turbo and 2015+ STi Document# 19-0099 Support: info@radiumauto.com This document covers the installation of a Radium dual catch can kit for the
More informationIAG Air / Oil Separator (AOS) For STi
IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,
More informationINSTALLATION INSTRUCTIONS
N-MT13-1 & N-MT13-2 COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS MUSTANG GT 2015-up PARTS INCLUDED Part Number Descrip on Qty 9-SA-INTAKE-100 Intake Assembly 1 9-SA-HEATSHIELD-100 Heatshield Assembly
More informationInstallation Manual v1.0: : Pulse Flow Exhaust Manifolds 2006 LBZ Duramax 6.6L EGR Equipped Vehicles
10/11/2013 204-901-4308 - INST Installation Manual v1.0: 204-901-4308: Pulse Flow Exhaust Manifolds 2006 LBZ Duramax 6.6L EGR Equipped Vehicles Figure 1 - Kit Contents 1 Please read all instructions before
More informationCOMPONENTS ILLUSTRATION
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION REMOVAL 1. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (a) Remove the windshield wiper motor and link assembly. 2. REMOVE COWL BODY MOUNTING REINFORCEMENT
More informationThis kit may void factory warranty please check with manufacturer.
Thank you for purchasing a Sinister Manufacturing Company EGR delete kit. Precision manufactured using aircraft quality 304 stainless steel and billet aluminum; this EGR kit is designed to endure years
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-822C (GUN METAL GRAY FINISH) 2008-12 Honda Accord 2.4L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-203DOS Air
More informationTABLE OF CONTENTS PARTS LIST
TROUBLESHOOTING: Note: You will have a check engine light and/or other problems unless using this product with a compatible ECM calibration. Contact your tuning supplier to learn whether or not aftermarket
More information18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines
8SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines KIT DESCRIPTION These service kits include all necessary parts to replace the low pressure fuel lines between the fuel filter housing and fuel
More information