Important! This product is NOT compatible with vehicles equipped with a manual transmission.

Transcription

1 Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide This guide supports the installation of a XK09 in Remote Start Ready (RSR) mode with or without a Plug & Play ( CHTHX & CHTHX) T-Harness (Optional). This solution offers two configuration options to control your system; x OEM Lock Remote Start Activation*, RF Kit (all sold separately). Refer to page 7 for a list of RF kits and their part numbers. *x OEM Lock Remote Start Activation is a feature that enables you to start/stop the vehicle using the OEM remote. Press the OEM remote LOCK button three () times within three () seconds to start the vehicle. To stop the vehicle, press the LOCK button three () more times. The OEM remote lock and unlock functions are inactive when the key is inserted into the ignition; therefore, the x OEM Lock Remote Start Activation feature cannot be used for Pit Stop mode. Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. Important! This product is NOT compatible with vehicles equipped with a manual transmission. Index Vehicle Application Guide... Installation Type a (with T-Harness)... Type b (without T-Harness)... Type a (with T-Harness)... Type b (without T-Harness)... Type a (with T-Harness)... Type b (without T-Harness)... Type (without T-Harness) Programming Module Programming for Type to... Module Programming for Type and Reset LED Diagnostics and Troubleshooting Optional RF Kits Using a XK09-CHRYSLER RSR... 9 Limited One-Year Consumer Warranty Chrysler, Dodge, Jeep and Volkswagen are registered trademarks and property of their respective companies.

2 Vehicle Application Guide Page Vehicles DL-Arm Factory Security DL-Disarm Factory Security *To select the proper install type, locate the ignition switch connector and select your install type as illustrated below: DL-Door Lock Control Chrysler 00 D D D D D 00/00c D D D D 00/00c D D D D D Aspen D D D D D Pacifica D D D D PT Cruiser D D D D D Sebring D D D D D Sebring Convertible D D D D D Sebring Sedan D D D D D Town & Country D D D D D Town & Country D D D D Dodge Avenger D D D D D Caliber or * or * D D D D D Caravan D D D D D Caravan D D D D Challenger D D D D D Challenger (Smart Key) D D D D D Charger D D D D Charger D D D D D Dakota D D D D D Durango D D D D D Durango D D D D D Grand Caravan D D D D D Grand Caravan D D D D Journey D D D D D Magnum D D D D Magnum D D D D D Nitro D D D D D RAM D D D D D RAM or * D D D D D Jeep Commander D D D D Commander D D D D D Compass D D D D D Grand Cherokee D D D D Grand Cherokee D D D D D Grand Cherokee (Smart Key) D D D D Liberty D D D D D Patriot D D D D D Wrangler D D D D D Wrangler Unlimited D D D D D Mitsubishi Raider D D D D D Ram 500 D D D D D 500 D D D D D 500 D D D D D C/V D D D D D Volkswagen Routan D D D D D Legend: D: Data-to-Data (DD) only DL: OE Door Lock & Alarm Controls PK: Transponder & Immobilizer Override SS: Entry Point Status-Security : DD and Wire-to-Wire (WW) KI: Ignition Key Sw itch Interface RS: Engine Start & Status ST: Function/Feature Status DL-Door Unlock DL-Sliding Door Control Driver DL-Sliding Door Control Passenger DL-Trunk / Hatch Release KI-Chrysler MUXX Activation KI-Key & Ignition.switch Interface PK-Immobilizer Bypass- Data No Key Req'd RS-x LOCK START (Start control using OEM Remote) RS-RAP Shut Down (Remote ACC Power) RS-Remote Start Ready RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-Hand Brake Status (+) Start, Pin No Start wire Installation Type does not have a Start wire 5 or 6 Connector side view at ignition switch Installation Type has a Start wire 5 or 6 Connector side view at ignition switch

3 Installation Type a (with T-Harness) Page Important! The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the XK09. LED (+)v XL0 Programming Button Antenna The optional XL0 and antenna are not included and MUST be purchased separately. XOVER Neutral Safety Switch 5: Blue: (-) Hood (+) v XK09 (-) Driver door pin Hood Pin : Black/White: (-) Parking Lights via Relay* OR* : Violet/Brown: Parking Light MUX* 0 : - : - : Green: RAP OFF : - Programming Button Purple wire in driver kick panel See page 5 for wiring information Ignition Barrel CHTHX (optional) Facing view Behind Ignition Switch Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked. *See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.

4 Installation Type b (without T-Harness) Page Important! The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the XK09. Neutral Safety Switch LED (+)v XL0 Programming Button Antenna The optional XL0 and antenna are not included and MUST be purchased separately. Hood Pin XOVER OR* (+) v 5: Blue: (-) Hood 9: Red: (+) V 0: Black: (-)Ground : Black/White: (-) Parking Lights* : Violet/Brown: Parking Light MUX* 5: Yellow 6: Brown: (+) V 7: Orange 9: Tan:HS CAN Low 0: Tan/Black: HSCAN High 0 XK09 : - : - : Green: RAP OFF : - Programming Button (-) Driver door pin Purple wire in driver kick panel See page 5 for wiring information CAN Low, Pin 6 CAN High, Pin 5, Pin (+) Ignition, Pin (+) V, Pin Ignition Barrel 6 Connector side view at ignition switch 7 Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked. *See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.

5 Parking Light Vehicle Wiring Reference Chart (Type ) Page 5 Vehicle Years Vehicle Wire Location on vehicle (+) / (-) Chrysler XK09 Output from Pin connector 00/00c 008- White/Brown Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Town & Country 0+ White/Green Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Town & Country White/Brown Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Dodge Caravan 0+ White/Green Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Caravan White/Brown Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Challenger 008- White/Brown Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Challenger (Smart Key) 008- White/Brown Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Charger White/Brown Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Durango 0+ White/Green Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Grand Caravan 0+ White/Green Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Grand Caravan White/Brown Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX : Black/White: (-) Parking Lights Journey White/Purple Passenger kick panel (+) via Relay Magnum 008 White/Brown Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX RAM 009- White Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Jeep Commander White/Dk. Blue Hazard light switch* (-) : Black/White: (-) Parking Lights Grand Cherokee White/Dk. Blue Hazard light switch* (-) : Black/White: (-) Parking Lights Grand Cherokee 0+ White/Green Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Grand Cherokee (Smart Key) 0+ White/Green Black connector at light switch, pin MUX : Violet/Brown: Parking Lights MUX Ram White Black connector at light switch, pin MUX : Violet/Brown: Parking Light MUX White Black connector at light switch, pin MUX : Violet/Brown: Parking Light MUX White Black connector at light switch, pin MUX : Violet/Brown: Parking Light MUX C/V 0 White Black connector at light switch, pin MUX : Violet/Brown: Parking Light MUX Volkswagen Routan 0+ White/Green Black connector at light switch, pin MUX : Violet/Brown: Parking Light MUX Routan White/Brown Black connector at light switch, pin MUX : Violet/Brown: Parking Light MUX * This connection will make the Hazard lights flash when remote started. Light switch, black 0-pin plug Light switch, black 6-pin plug (+) Passenger kick panel To vehicle s (+) Parking Lights a 0 (-) Hazard Light Switch +v Fuse 5A : Violet/Brown: Parking Light MUX* : Violet/Brown: Parking Light MUX* : Black/White: (-) Parking Lights : Black/White: (-) Parking Lights

6 Installation Type a (with T-Harness) Page 6 Important! The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the XK09. Neutral Safety Switch Hood Pin To vehicle s (+) Parking Lights See page 8 for wiring information XOVER LED (+)v XL0 Programming Button Antenna The optional XL0 and antenna are not included and MUST be purchased separately a 0 XK09 Fuse 5A +v 5: Blue: (-) Hood : Black/White: (-) Parking Lights 0 : - : - : - : - Programming Button CHTHX (optional) 8 Connector side view at ignition switch Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.

7 Installation Type b (without T-Harness) Page 7 Important! The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the XK09. Neutral Safety Switch Hood Pin To vehicle s (+) Parking Lights LED (+)v XL0 Programming Button Antenna The optional XL0 and antenna are not included and MUST be purchased separately XOVER 87a 0 (+) v XK09 Fuse 5A +v See page 8 for wiring information 5: Blue: (-) Hood 9: Red: (+) V 0: Black: (-)Ground : Black/White: (-) Parking Lights : Violet/Brown: Multiplex Output 6: Brown: (+) V 9: Tan:HS CAN Low 0: Tan/Black: HSCAN High 0 : - : - : - : - : - : - : Pink/White: (+) Ignition Output : - Programming Button CAN Low, Pin 7 CAN High, Pin 6 (+) V, Pin 5, Pin (+) Ignition, Pin MUX, Pin 8 Connector side view at ignition switch Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.

8 Parking Light Vehicle Wiring Reference Chart (Type ) Page 8 Vehicle Years Wire (+) / (-) Location Chrysler 00 0 White/Violet (+) Driver kick panel Aspen Pink/Red (+) Driver kick fuse box, black 0-pin plug, pin 6 Sebring White/Violet (+) Driver kick panel Sebring Convertible White/Violet (+) Driver kick panel Sebring Sedan White/Violet (+) Driver kick panel Dodge Avenger 008- White/Violet (+) Driver kick panel Caliber 007- White/Violet (+) Driver kick panel Dakota 007- Pink/Red (+) Underhood fuse box, black 0-pin plug, pin 5 Durango Pink/Red (+) Driver kick fuse box, black 0-pin plug, pin 6 Nitro 007- White/Violet (+) Driver kick panel RAM White/Gray (+) Above driver kick, gray 7-pin plug, pin 9 Jeep Compass 007- White/Violet (+) Driver kick panel Liberty White/Violet (+) Driver kick panel Patriot 007- White/Violet (+) Driver kick panel Wrangler 007- White/Violet (+) Passenger kick panel Wrangler Limited 007- White/Violet (+) Passenger kick panel Mitsubishi Raider Pink/Red (+) Underhood fuse box, black 0-pin plug, pin 5 Driver kick fuse box, black 0-pin plug Underhood fuse box, black 0-pin plug Above driver kick, gray 7-pin plug

9 Installation Type a (with T-Harness) Page 9 Important! The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the XK09. Hood Pin Neutral Safety Switch LED (+)v XL0 Programming Button Antenna The optional XL0 and antenna are not included and MUST be purchased separately. XOVER XK09 See page for wiring information 5: Blue: (-) Hood : Black/White: (-) Parking Lights* 5: Yellow: (+) Starter 0 Programming Button CHTHX (optional) 8 Connector side view at ignition switch (+) Start, Pin Violet/Brown, Pin 5 or 6 Connector side view at ignition switch Cut Purple/Brown wire, Pin 8 (on male end) Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked. *See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.

10 Installation Type b (without T-Harness) Page 0 Important! The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the XK09. Neutral Safety Switch Hood Pin LED (+)v XL0 Programming Button Antenna The optional XL0 and antenna are not included and MUST be purchased separately. XOVER (+) v 5: Blue: (-) Hood XK09 See page for wiring information 9: Red: (+) V 0: Black: : Black/White: (-) Parking Lights* : Violet/Brown: Multiplex Output 6: Brown: (+) V 5: Yellow: (+) Starter 9: Tan:HS CAN Low 0: Tan/Black: HSCAN High 0 : - : - : - : - : - : - : Pink/White: (+) Ignition Output : - Programming Button (+) V a CAN High, Pin 6 (+) V, Pin 5, Pin CAN Low, Pin 7 (+) Start, Pin (+) Ignition, Pin Violet/Brown, Pin 0 8 Connector side view at ignition switch 5 or 6 Connector side view at ignition switch Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked. *See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.

11 Parking Light Vehicle Wiring Reference Chart (Type ) Page Vehicle Years Wire (+) / (-) Location Chrysler 00/00c White/Violet (+) Passenger kick panel PT Cruiser White/Violet (+) Driver kick panel Dodge Caliber 007- White/Violet (+) Driver kick panel Charger White/Violet (+) Passenger kick panel Magnum White/Violet (+) Passenger kick panel RAM 006 White/Gray (+) Above driver kick, gray 7-pin plug, pin 9 Jeep Commander White/Dk. Blue (-) Hazard light switch* Grand Cherokee White/Dk. Blue (-) Hazard light switch* * This connection will make the Hazard lights flash when remote started. Above driver kick, gray 7-pin plug 7 8 (+) Parking Lights (see table for location) To vehicle s (+) Parking Lights a (-) Hazard Light Switch v Fuse 5A : Black/White: (-) Parking Lights : Black/White: (-) Parking Lights

12 Installation Type (without T-Harness) Page Important! The Hood Pin and Neutral Safety Switch are mandatory security devices, but are NOT supplied with the XK09. Neutral Safety Switch Hood Pin LED (+)v XL0 Programming Button Antenna The optional XL0 and antenna are not included and MUST be purchased separately. XOVER +v Fuse 5A Parking Lights a 0 (+) V 5: Blue: (-) Hood XK09 Chrysler Pacifica requires a resistor. See diagram on page (+) V, Pin 6, Pin 5 (+) Ignition,Pin Pin, J850 9: Red: (+) V 0: Black: : Black/White: (-) Parking Lights : Violet/Brown: Multiplex Output 5: Yellow 7: Orange 8: Green: J850 0 Connector side view at ignition switch : - : Orange/Red: (+) Starter : Pink/White: (+) Ignition Output : - Programming Button 6 Module-Sentry Key Remote Entry (+) Start, Pin (+) Ignition, Pin (+) Violet/Brown, Pin Only connect with Pacifica Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.

13 Parking Light Vehicle Wiring Reference Chart (Type ) Page Vehicle Years Wire (+) / (-) Location Chrysler Pacifica Brown/White (-K) MUX Headlight switch, black -pin plug, pin 6 Town & Country White/Orange (+) Driver kick panel Dodge Caravan White/Orange (+) Driver kick panel Grand Caravan White/Orange (+) Driver kick panel Headlight switch, black -pin plug (+) Parking Lights KÙ 5 6 To vehicle s (+) Parking Lights a 0 +v OR To vehicle s (MUX) Parking Lights : Black/White: (-) Parking Lights 87a : Black/White: (-) Parking Lights +v Fuse 5A Positive (+) MUX

14 Module Programming for Type to Page Refer to the LED Diagnostics section on page 6 for more information and for troubleshooting purposes. Connect the -pin DD harness to the XL0 module, then connect the 0-pin harness. Caution! The 0-pin connector can be easily plugged in backwards. XL0 -pin 0-pin The LED turns ON solid or flashes rapidly. Connect one or both of the other -pin harnesses, depending on the requirements of each installation types. On Solid or Flashes -pin Make sure the hood of the vehicle is open before proceeding to step. (Hood pin to Ground) Caution! Failure to do so will NOT put the module in RSR mode and may cause unexpected behavior in the car. 5 Turn Insert the key into the ignition barrel and turn it to ON. Wait for the LED to start flashing slowly. the key back to the OFF position. KEY OFF Key at ON ON START & KEY Flashes OFF ON START Key at OFF WITHOUT Factory Keyless Remote 6 Press the module programming button. The LED flashes quickly for second, turns ON solid for seconds, then turns OFF. The module is now programmed. WITH Factory Keyless Remote 6 Press the UNLOCK button on the factory keyless remote. The LED flashes quickly for second, turns ON solid for seconds, then turns OFF. The module is now programmed. Press & LED Sequence Press Unlock & LED Sequence Important! If the LED does not flash quickly for second at step 6, the module is NOT in RSR mode. Reset the module and repeat the programming sequence. You must make sure the vehicle hood is open in step.

15 Module Programming for Type Page 5 Refer to the LED Diagnostics section on page 6 for more information and for troubleshooting purposes. Connect the -pin DD harness to the XL0 module, then connect the 0-pin harness. Caution! The 0-pin connector can be easily plugged in backwards. XL0 -pin 0-pin The LED turns ON solid. On Solid Connect one or both of the other -pin harnesses, depending on the requirements of each installation types. -pin Make sure the hood of the vehicle is open (Hood pin to Ground) before proceeding to step. Caution! Failure to do so will NOT put the module in RSR mode and may cause unexpected behavior in the car. 5 Insert the key into the ignition barrel to the OFF position. Wait for the LED to start flashing quickly. Turn the key to ON position. The LED will flash slowly then quickly for second, turns ON solid for seconds, then turns OFF (it could take up to 0 seconds). The module is now programmed and ready to use. KEY KEY OFF OFF ON Key at OFF ON Key at ON START START & & LED Sequence LED Sequence Important! If the LED does not flash quickly for second at step 5, the module is NOT in RSR mode. Reset the module and repeat the programming sequence. You must make sure the vehicle hood is open in step. Module Reset Disconnect the module from any power source. Press and HOLD the programming button. While holding the button, connect the module to the power source. Wait until the red LED flashes once and release the programming button. Disconnect from Power & Press & Hold Connect to Power & Flashes Once Release

16 LED Diagnositics and Troubleshooting Page 6 LED Status Description Troubleshooting During Power Up x secs x secs x Flashes quickly Module is in Standalone mode. for second The bus type cannot be Solid detected. The vehicle type is not yet Flashes quickly detected. Flashes slowly Solid for seconds Flashes once quickly Waiting for keyless. Module was successfully programmed or is already programmed. Modules was reset. Normal operation. Make sure the T-Harness is properly connected and insert the key in the ignition switch. Insert the key in the ignition switch and turn to the ON position. You may need to wait up to 0 seconds. Remove the key from the ignition switch and press Unlock on the factory remote. Normal operation. Normal operation if the Programming button was held during the power up sequence. Off Module has no power. Check the power connections. Remote Start Period Solid Incorrect behavior. Data is not processing correctly. Disconnect the power from the module and power up. Off No Start command was received. Make sure the module was programmed with the hood open (Ground on Blue wire). If not, reset the module and reprogram it with the hood open. x sec Flashes for Normal operation upon receiving a command from the A command is processing. second remote. Flashes The unit is in a remote start sequence. Normal operation during runtime. Programmed & Installed (Idle) Off The unit is waiting for a command. Normal operation. x Flashes for Normal operation upon receiving a command from the sec A command is processing. second remote. Solid Incorrect behavior. Data is not processing correctly. Disconnect the power from the module and power up.

17 Optional RF Kits Page 7 Note: RF kits are sold SEPARATELY. Request an order from Directed using the part numbers listed below. 9VL Viper -Way Responder ONE - Plug & Play RF Kit with XL0. UPC: Also available as: Python: 9PL Clifford: 9XL 95VL Viper -Way - Plug & Play RF kit with XL0. UPC: Also available as: Python: 95PL Clifford: 95XL 95VL Viper -Way Responder LE - Plug & Play RF Kit with XL0. UPC: Also available as: Python: 95PL Clifford: 95XL 975VL Viper -Way LC - Plug & Play RF kit with XL0. UPC: Also available as: Python: 975PL Clifford: 975XL

18 Optional RF Kits Page 8 Note: RF kits are sold SEPARATELY. Request an order from Directed using the part numbers listed below. AF-RFK6 AF-RFK55 Astrostart -way LED Receiver kit with up to,500 of range. UPC: Astrostart -way LCD Receiver kit offering TM XRT technology with up to 5,000 of range. UPC: AS-RFK700 AS-RFK00 Autostart -way Receiver kit with up to,000 of range. UPC: Autostart -way LED Receiver kit offering TM HDR technology with up to,000 of range. UPC:

19 PANIC Using your XK09-CHRYSLER RSR Page 9 Takeover with Smart Key Press the button to remote start the vehicle.* Press button to remote start* Enter the vehicle, while making sure the key is inside with you. Enter vehicle with the Smart Key in hand Important: Do NOT press the brake pedal. Press the Push-to-Start (PTS) button twice to turn the ignition ON. Do NOT press the brake pedal X ENGINE START STOP PUSH You can now put the vehicle in gear and drive off. Ready to drive off * Your aftermarket remote starter model may differ from the one shown in the illustrations. Takeover with Key Press the button to remote start the vehicle.* Enter the vehicle and turn the key to ignition. Press button to remote start* KEY OFF ON Key at ON START You can now put the vehicle in gear and drive off. Ready to drive off * Your aftermarket remote starter model may differ from the one shown in the illustrations.

20 Using your XK09-CHRYSLER RSR Page 0 Pit Stop with Smart Key Stop the vehicle in a safe parking spot and put the gear in Park (P). Stop & put vehicle in Park (P) & P Press the button to activate the remote start.* Press button to remote start* Important: Do NOT press the brake pedal. Press the Push-to-Start (PTS) button once to turn the ignition OFF. Do NOT press the brake pedal X ENGINE START STOP PUSH You can now exit the vehicle. * Your aftermarket remote starter model may differ from the one shown in the illustrations. Pit Stop with Key Stop the vehicle in a safe parking spot and put the gear in Park (P). Stop & put vehicle in Park (P) & P Press the button to activate the remote start.* Press button to remote start* Turn the key to OFF position and remove it from the barrel. You can now exit the vehicle. KEY OFF ON Key at OFF START * Your aftermarket remote starter model may differ from the one shown in the illustrations.

21 Limited One-Year Consumer Warranty Page For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. PROTECTED BY U.S. PATENTS: 5,79,55; 6,0,60 B *;6,,00 B; 6,9,6 B; 6,75,7 B; 6,97,7 B; 6,6,876 B; 6,9,5 B; 6,59, B; 6,696,97 B; 6,756,885 B; 6,756,886 B; 6,77,67 B; 6,8,89 B; 6,9,750 B; 7,00,0 B; 7,05,80 B; 7,0,86 B; 7, 0 6, 6 B ; 7,06,7 B; 7,068,5 B; 7,05,679 B; CDN. PATENT:,0,8;,,99;,5,0;,5,0;,5,07;,5,08;,5,0;, 0, 9 7 ;,6,670;,5,089 EUROPEAN PATENT:,05,8 PAT. PENDING:,9,06; MADE IN CANADA