This module can only be flashed and configured using XpressVIP at or using the Directechs

Transcription

1 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The HYUNDAI firmware for DBALL is an all-in-one door lock and override module compatible with specific Hyundai and Kia vehicles. This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode. This solution offers three () configuration options to control your system: x OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately). This module can only be flashed and configured using XpressVIP at or using the Directechs Mobile application for smartphones. Refer to the Module Programming section for more information. Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. Important! This product is NOT compatible with vehicles equipped with a manual transmission. Takeover feature is NOT available on the Kia Optima. The engine will stop when a door is opened. Index Vehicle Application Guide... Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Type... Type... Type... Type... Type... Type 6... SmartStart/XL0 Installation Notes Programming Module Programming... Module Reset & Hard Reset... Feature & Option List... Feature Programming LED Diagnostics & Troubleshooting... Parking Light Error Codes... Limited One-Year Consumer Warranty... Quick Reference Guide... 9 SmartStart Compatible SmartStart is equipped with DD, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information. Hyundai and Kia are registered trademarks and property of their respective companies.

2 Vehicle Application Guide Page The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles Hyundai PK-Immobilizer Bypass-Data No Key Req'd AV-Panic Mode Activation DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release RS-x LOCK START (Start control using OEM Remote) RS-RAP Shut Down (Retained ACC Power) RS-Remote Start Ready RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-Ignition Status Genesis (Smart Key) Genesis Coupe (Smart Key) Sonata (Smart Key) Sonata Hybrid Kia Magentis (Smart Key) Optima (Smart Key) Sorento (Smart Key) Legend: D: Data-to-Data (DD) only AV: Horn & Lights Controls RS: Remote Start & Engine Controls : DD and WW CC: Comfort & Convenience Controls SS: Integrated Security & Monitoring DL: OE Door Lock & Alarm Controls ST: Function/Feature Status PK: Transponder & Immobilizer Override FOB: Sync CAN Interface w / FOB Remote

3 Installation Type Page Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. (+) Ignition Status:Yellow/Black, pin 9 Diagnostic connector OBDII (connector side view) PDM (Power Distribution Module) Center console on driver side (-) Keysense: Orange, pin B-CAN Low: White, pin B-CAN High: Brown, pin C-CAN High: Orange, pin C-CAN Low: Green, pin Hood Pin HS CAN High: Tan/Black: HS CAN Low: Tan: FT CAN High: Orange/Green: FT CAN Low: Orange/Brown: 6 (+)V Input: Brown: 7 (+) PTS Output: Yellow: 8 (+) V Input: Red: (-) Ground: Black: (-) Parking Light Output: Green/Black: (+) Brake Output: Gray/Black: 7 (-) Keysense Output: Yellow/Black: 0 RF 0 Remote Start Safety Override Switch 6: White/Black: (-) Hood Input 9: Pink: (+) Ignition Input (+) PTS : Orange/Black, pin A Diodes (+) PTS : White, pin 7 Prog. Button LED DBALL PTS Connector (black conn. at Start/Stop Switch) You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. (+) R. Park. Light: White, pin 6 Amp Diodes (+) L. Park. Light: Brown, pin a a 0 Brake pedal (+) Brake: Gray, pin Refer to for alternative brake connections Fuse A Fuse 0 A EF - Black -pin conn. (Passenger kick panel) (+) V: White, pin I/P Junction Box (Driver Side Dash - Rear View) With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

4 Type - Vehicle Wiring Reference Chart Page Wire Information Connector Information Function Color Pin Polarity Location Color Pins Hyundai Genesis (Smart Key) HS CAN High Orange 6 Data OBDll. Black 6 HS CAN Low Green Data OBDll. Black 6 FT CAN High Brown Data Power distribution module in center console on driver side. White 0 FT CAN Low White 0 Data Power distribution module in center console on driver side. White 0 Keysense Orange (-) Power distribution module in center console on driver side. White 0 Ignition Yellow/Black 9 (+) Power distribution module in center console on driver side. White 0 Brake Gray (+) Brake switch. White Parking Lights (Left) Brown (+) Passenger kick. Black Parking Lights (Right) White (+) Passenger kick. Black V White (+) Drivers dash fuse box. White PTS Orange/Black (+) Start/stop switch. Black 0 PTS White 7 (+) Start/stop switch. Black 0

5 Platform: DBALL Installation Type Page Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. Diagnostic connector OBDII (connector side view) C-CAN High: Red, pin PDM (Power Distribution Module) Above gas pedal White connector (-) Keysense: Red, pin B-CAN Low: Blue, pin B-CAN High: Red, pin 9 6 HS CAN High: Tan/Black: HS CAN Low: Tan: FT CAN High: Orange/Green: C-CAN Low: Blue, pin Hood Pin Remote Start Safety Override Switch Brake pedal (+) Brake: Green, pin FT CAN Low: Orange/Brown: 6 (+)V Input: Brown: 7 (+) PTS Output: Yellow: 8 (+) V Input: Red: (-) Parking Light Output: Green/Black: (-) Keysense Output: Yellow/Black: 0 6 (-) Ground: Black: (+) Brake Output: Gray/Black: 7 6 RF Prog. Button LED DBALL 0 6: White/Black: (-) Hood Input 9: Pink: (+) Ignition Input A Diode OR A Diodes a 0 Fuse 0 A (+) V: Red, pin (+) PTS : Blue, pin (+) PTS : Pink, pin C PTS Connector (black conn. at Start/Stop Switch) (-) Parking Lights: Brown/Black, pin 8 9 D A B C D I/P - Driver Side Fuse Box (see back of I/P) (+) Ignition Status: Blue, pin A You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. Blue -conn. (Driver Kick Panel) [] (-) Hood Status: Yellow, pin [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

6 Type - Vehicle Wiring Reference Chart Page 6 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Hyundai Genesis Coupe (Smart Key) 00-0 HS CAN High Red 6 Data OBDll. Black 6 HS CAN Low Blue Data OBDll. Black 6 FT CAN High Red Data Power distribution module in center console on driver side. White 0 FT CAN Low Blue 0 Data Power distribution module in center console on driver side. White 0 Keysense Red (-) Power distribution module in center console on driver side. White 0 Ignition Blue (+) Drivers dash fuse box. White 8 Brake Green (+) Brake switch. White Parking Lights Brown/Black 8 (-) Drivers dash fuse box. White 6 V Red (+) Drivers dash fuse box. White 0 Hood pin Yellow (-) Drivers kick. Blue PTS Blue (+) Start/stop switch. Black 0 PTS Pink 7 (+) Start/stop switch. Black 0

7 Installation Type Page 7 Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. (+) PTS : Yellow/Black, pin White/Gray Connector (Passenger Kick Panel or Driver Kick Panel for Hybrid) (-) Keysense: Yellow or Orange/Black, pin OR (-) Keysense: Yellow (Hybrid), pin 7 A Diode (+) PTS : Yellow/Orange, pin Refer to for alternative brake connections PTS Connector (black conn. at Start/Stop Switch) 0 B-CAN Low: Yellow/Orange or Orange (Hybrid), pin Brake Pedal B-CAN High: White/Orange or Blue (Hybrid), pin I/P Junction Box - Driver Side Dash (see back of I/P Junction Box) C-CAN High: White, pin 6 HS CAN High: Tan/Black: HS CAN Low: Tan: FT CAN High: Orange/Green: FT CAN Low: Orange/Brown: 6 (+)V Input: Brown: 7 (+) PTS Output: Yellow: 8 (+) V Input: Red: (-) Ground: Black: (-) Parking Light Output: Green/Black: (+) Brake Output: Gray/Black: 7 (-) Keysense Output: Yellow/Black: 0 Diagnostic Connector OBDII (connector side view) 8 9 RF 6 C-CAN Low: Yellow or Brown (Hybrid), pin Prog. Button LED DBALL 0 Hood Pin Remote Start Safety Override Switch 6: White/Black: (-) Hood Input 9: Pink: (+) Ignition Input (+) Brake: Green or Green/Orange (Hybrid), pin (-) Parking Lights: Pink, pin I/P Junction Box Driver Side Dash (front view) (+) Ignition Status: Pink, pin Ignition Connector a Fuse 0 A BCM - Above Gas Pedal (+)V: Red, pin You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

8 Type - Vehicle Wiring Reference Chart Page 8 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Hyundai Sonata (Smart Key) 0-0 HS CAN High White 6 Data OBDll. Black 6 HS CAN Low Yellow Data OBDll. Black 6 FT CAN High White/Orange Data I/P junction box - driver side dash. White FT CAN Low Yellow/Orange 0 Data I/P junction box - driver side dash. White Ignition Pink (+) I/P junction box - driver side dash. Black 0 V Red (+) I/P junction box - driver side dash. Black 9 Keysense Yellow or Orange/Black (-) Passenger kick. White 6 Brake Green (+) Brake switch. White Parking Lights Pink (-) BCM above gas pedal. Gray PTS Yellow/Black (+) Start/stop switch. Black 0 PTS Yellow/Orange 7 (+) Start/stop switch. Black 0 Hyundai Sonata Hybrid 0-0 HS CAN High White 6 Data OBDll. Black 6 HS CAN Low Brown Data OBDll. Black 6 FT CAN High Blue Data I/P junction box - driver side dash. White FT CAN Low Orange 0 Data I/P junction box - driver side dash. White Ignition Pink (+) I/P junction box - driver side dash. Black 0 V Red (+) I/P junction box - driver side dash. Black 9 Keysense Yellow 7 (-) Drivers kick. White 0 Brake Green/Orange (+) Brake switch. White Parking Lights Pink (-) BCM above gas pedal. Gray PTS Yellow/Black (+) Start/stop switch. Black 0 PTS Yellow/Orange 7 (+) Start/stop switch. Black 0

9 Installation Type Page 9 Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. A B C Diagnostic Connector OBDII (connector side view) C-CAN High: White, pin 6 A Diodes (+) PTS : Orange/Black, pin PTS Connector (black conn. at Start/Stop Switch) 8 (+) PTS : White/Orange, pin 7 BCM (Above Brake Pedal) 9 6 C-CAN Low: Black, pin Hood Pin C B-CAN High: White, pin B-CAN Low: Black, pin HS CAN High: Tan/Black: HS CAN Low: Tan: FT CAN High: Orange/Green: Remote Start Safety Override Switch A (+) Ignition Status: Yellow/Black, pin (-) Driver Door Trigger Blue/Black, pin 0 FT CAN Low: Orange/Brown: 6 (+)V Input: Brown: 7 (+) PTS Output: Yellow: 8 (+) V: Red: (-) Ground: Black: (-) Parking Light Output: Green/Black: (+) Brake Output: Gray/Black: 7 (-) Keysense Output: Yellow/Black: 0 (-) Autolight Off Output: Blue/Red: RF 0 6: White/Black: (-) Hood Input [] 9: Pink: (+) Ignition Input A Diode OR Prog. Button LED DBALL Key Port - Under Center Arm Rest (-)KeySense: Orange, pin 7 (-) Parking Lights: Yellow/ Black, pin I/P Box (Above Driver Kick Panel) Connector G 6 7 (+) Brake: Brown, pin B [] (-) Hood Status: Yellow/Black, pin G (+) V: Red, pin 87a 0 Brake Pedal You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

10 Type - Vehicle Wiring Reference Chart Page 0 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Kia Magentis (Smart Key) 00 HS CAN High White 6 Data OBDll. Black 6 HS CAN Low Black Data OBDll. Black 6 FT CAN High White Data BCM above Brake pedal. Gray 8 FT CAN Low Black Data BCM above Brake pedal. Gray 8 Ignition Yellow/Black (+) BCM above Brake pedal. White Driver Door Trigger Blue/Black 0 (-) BCM above Brake pedal. White Parking Lights Yellow/Black (-) BCM above Brake pedal. White 0 Hood Pin Yellow/Black (-) BCM above Brake pedal. White 0 V Red (+) I/P Junction box above driver kick. White Keysense Orange 9 (-) Key port in center console. White 0 Brake Brown (+) Brake switch. White PTS Orange/Black (+) Start/stop switch. Black 0 PTS White/Orange 7 (+) Start/stop switch. Black 0 Kia Optima (Smart Key) 00 HS CAN High White 6 Data OBDll. Black 6 HS CAN Low Black Data OBDll. Black 6 FT CAN High White Data BCM above Brake pedal. Gray 8 FT CAN Low Black Data BCM above Brake pedal. Gray 8 Ignition Yellow/Black (+) BCM above Brake pedal. White Driver Door Trigger Blue/Black 0 (-) BMC above Brake pedal. White Parking Lights Yellow/Black (-) BCM above Brake pedal. White 0 Hood Pin Yellow/Black (-) BCM above Brake pedal. White 0 V Red (+) I/P Junction box above driver kick. White Keysense Orange 9 (-) Key Port - IN Center Console White 0 Brake Brown (+) Brake switch. White PTS Orange/Black (+) Start/stop switch. Black 0 PTS White/Orange 7 (+) Start/stop switch. Black 0

11 Installation Type Page Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. (-) Keysense:Red or Red/Orange, pin B-CAN Low: Red, pin 6 IPM - Driver Side Dash (see back of IPM) White Connector B-CAN High: Blue, pin Fuse 0 A White Connector White Connector (+) V: Red, pin (-) Driver Door Trigger: Green/Orange, pin 0 B A IPM - Driver Side Dash (front view) B Red Connector A C D C White Connector D (+) Ignition Status: Green, pin 7 Refer to for alternative brake connections. Brake Pedal a 0 (+) Brake: Yellow or Green/Black, pin Diagnostic Connector OBDII (connector side view) HS CAN High: Tan/Black: HS CAN Low: Tan: FT CAN High: Orange/Green: FT CAN Low: Orange/Brown: 6 (+)V Input: Brown: 7 (+) PTS Output: Yellow: 8 (+) V Input: Red: (-) Ground: Black: (-) Parking Light Output: Green/Black: (+) Brake Output: Gray/Black: 7 (-) Keysense Output: Yellow/Black: 0 (-) Autolight Off Output: Blue/Red: C-CAN High: White, pin C-CAN Low: Red, pin RF 6 0 (-) Hood Status: Red/Black, pin 6 [] Hood Pin Remote Start Safety Override Switch 6: White/Black: (-) Hood Input 9: Pink: (+) Ignition Input A Diode OR (-) Parking Lights: Blue, pin (+) PTS : Orange/Black, pin A Diodes (+) PTS : White/Orange, pin 7 Prog. Button LED DBALL IPM - Driver Side Dash (see back of IPM) White Connector PTS Connector (black conn. at Start/Stop Switch) You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

12 Type - Vehicle Wiring Reference Chart Page Wire Information Connector Information Function Color Pin Polarity Location Color Pins Kia Sorento (Smart Key) 00-0 HS CAN High White 6 Data OBDll. Black 6 HS CAN Low Red Data OBDll. Black 6 FT CAN High Blue Data IPM driver side dash. White 6 FT CAN Low Red 6 Data IPM driver side dash. White 6 Keysense Red or Red/Orange 8 (-) IPM driver side dash. White 6 Ignition Green 7 (+) IPM driver side dash. White 0 Driver Door Trigger Green/Orange 0 (-) IPM driver side dash. White 6 Parking Lights Lt.Blue (-) IPM driver side dash. White 6 Hood Pin Red/Black 6 (-) IPM driver side dash. Red 0 V Red (+) IPM driver side dash. White Brake Yellow or Green/Black (+) Brake switch. White PTS Orange/Black (+) Start/stop switch. Black 0 PTS White/Orange 7 (+) Start/stop switch. Black 0

13 Installation Type 6 Page Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. I/P - D I/P-A I/P-D B-CAN High: Red, pin B-CAN Low: Blue, pin 6 I/P Junction Box (Driver Side Dash - Rear View) I/P - A (+) PTS : Orange/ Black, pin PTS Connector (black conn. at Start/Stop Switch) (+) PTS : White/Orange, pin 7 I/P-E Diagnostic Connector OBDII (connector side view) 8 9 C-CAN High: Red, pin 6 6 C-CAN Low: Blue, pin Hood Pin (+) Ignition Status: Green, pin I/P - E 0 9 (+) V: Green, pin 9 Refer to for alternative brake connections. A Diodes (+)Brake: Red/Black, pin HS CAN High: Tan/Black: HS CAN Low: Tan: FT CAN High: Orange/Green: FT CAN Low: Orange/Brown: 6 (+)V Input: Brown: 7 (+) PTS Output: Yellow: 8 (+) V Input: Red: (-) Ground: Black: (-) Parking Light Output: Green/Black: (+) Brake Output: Gray/Black: 7 (-) Keysense Output: Yellow/Black: 0 RF 0 Remote Start Safety Override Switch 6: White/Black: (-) Hood Input 9: Pink: (+) Ignition Input Prog. Button LED DBALL Brake Pedal (-) Parking Lights: Yellow, pin M8 - L Parking Light Connector (-) Keysense: Pink, pin PDM - Above Gas Pedal White Connector You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

14 Type 6 - Vehicle Wiring Reference Chart Page Wire Information Connector Information Function Color Pin Polarity Location Color Pins Hyundai Genesis Coupe (Smart Key) 0-0 HS CAN High Red 6 Data OBDll. Black 6 HS CAN Low Blue Data OBDll. Black 6 FT CAN High Red Data I/P junction box - driver side dash. White FT CAN Low Blue 6 Data I/P junction box - driver side dash. White Ignition Green (+) I/P junction box - driver side dash. White 0 V Green 9 (+) I/P junction box - driver side dash. White 8 Keysense Pink (-) PDM above gas pedal. White 0 Brake Red/Black (+) Brake switch. White Parking Lights Yellow (-) Headlights switch. White PTS Orange/Black (+) Start/stop switch. Black 0 PTS White/Orange 7 (+) Start/stop switch. Black 0

15 SmartStart/XL0 Installation Notes Page The DBALL Remote Start Ready (RSR) solution offers three () configuration options to control your system; x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL0. SmartStart Revision A SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (White & Brown or Blue) Cut Brown or Blue Loop OR DBALL CABLE pins DD ( pins, white) pins, not used LED SmartStart The modules must be connected in a specific order. Refer to the Module Programming section for more information. SmartStart Revision B SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (Gray & White) Connect Gray wire to (-) Ground pins DBALL CABLE pins pins, not used THIS SIDE UP DD ( pins, white) LED The modules must be connected in a specific order. Refer to the Module Programming section for more information. RF Kit The optional XL0 and antenna are not included and MUST be purchased separately. DBALL XOVER LED XL0 Prog. Button Antenna. Use the DD Crossover (XOVER) cable that is provided with XL0, and NOT the one in the DBALL package.. The modules must be connected in a specific order. Refer to the Module Programming section for more information. RF Kit & PKE Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (N0T) for detailed wiring information. RF Kit, PKE & SmartStart BT Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (N0T) for detailed wiring information.

16 Module Programming Page 6 Refer to the LED Diagnostics section for more information and for troubleshooting purposes. Important Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step. Note: Before connecting either the XL0 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version. or higher). Visit to download the latest version of the application. Warning! To take advantage of advanced features, you must use XpressVIP. (and higher) or the Directechs Mobile app. Flashing a module using your computer:. Connect the interface module to your computer using the XKLoader.. Go to using Internet Explorer, and select the Config for RSR button.. Follow the instructions to select your vehicle, installation type, and configure your options.. Once you have configured the firmware options, click on the FLASH button. Flashing a module using your smartphone or tablet. Connect the interface module to your XKLoader.. Launch the Directechs Mobile app on your smartphone or tablet.. Select FLASH YOUR MODULE and follow the on screen instructions. When the flashing operation is successful, you can proceed with the programming instructions below. SmartStart Installation The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL. a. To ensure that the DD communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart). b. Do NOT connect the -pin harness (on SmartStart). Power and ground will be provided by the DBALL DD connector. Connect SmartStart to DBALL using the DD port. OR XL0 Installation Connect XL0 to DBALL using the DD port. SmartStart XL0 DD 0-pin DD 0-pin Connect the 0-pin, -pin and -pin harnesses to DBALL, then wait until the LED turns ON solid red. Note: To skip the transponder programming and use convenience features only press the programming button times, The LED will turn orange then proceed to step. st DD 0-pin rd nd -pin -pin & Solid Without pressing the brake and with the key inside the vehicle, press the Push-to-Start (PTS) button twice to turn the ignition ON. The LED will turn ON solid green for sec. then OFF. Note: When skipping transponder programming, the orange LED flashes then the orange LED turns ON for seconds and shuts off. Press the Push-to-Start (PTS) button once more to turn the ignition OFF. Solid x secs Do NOT press the brake pedal & Off X X ENGINE START STOP ENGINE START STOP PUSH PUSH You have successfully completed the module programming sequence.

17 Module Reset Page 7 A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected. If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. st DD 0-pin th nd rd -pin -pin Wait seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red. & & Hard Reset Solid Release Solid Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and DD options) may have to be reconfigured. See the Feature & Option List section of this guide. If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. st DD 0-pin th nd rd -pin -pin Wait seconds until the LED turns ON solid orange, and wait 0 more seconds until the LED starts to flash orange and red. Solid & Release the programming button. The LED turns ON solid red. Release & Solid

18 Feature & Option List Page 8 It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on The web offers more options such as EIPS and RSR; however, manual configuration of the features is possible using the information on this page. * Default option Feature Operation / Option Description RF Output Type Unlock Driver Priority Automatic Controlled Door Lock. Disabled* Module is connected to a remote starter using a standard installation.. RFTD Output Module is connected to an XL0 using an RSR or RXT installation (when available).. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).. Driver Priority* Unlocks only the driver door when the button is first pressed, and unlocks all doors when it is pressed a second time within seconds.. All Unlocks all doors when the button is first pressed.. Disabled* The vehicle doors will not lock automatically.. Ignition The vehicle doors will lock when ignition is turned ON and unlock when ignition is OFF.. Brake The vehicle doors will lock when the brake pedal is applied and unlock when ignition is OFF.. Disabled The OEM alarm will not be controlled by the interface upon remote start. No disarm or arm command will be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter. Smart OEM Alarm Control. Safelock. Enabled* Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown. Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start sequence, only when required. Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Feature Programming To enter feature programming routine - Turn the ignition ON, then OFF. - Within seconds, press and HOLD the programming button until the LED turns ON orange (after seconds). Release the Programming button. - The LED will flash green once slowly to indicate the feature number is. After a short delay, the LED flashes red rapidly to indicate the current option of feature (i.e. x green followed by x red indicates feature is set to option ). The flashing sequence will repeat until a new command is entered. Changing feature options - Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the DBALL in RSR using x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 0-pin harness to ground will change the option for the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered. Accessing another feature - Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered. When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option. Once a feature is programmed - Other features can be programmed. - The feature programming can be exited. Programming Button Exiting feature programming - No activity for 0 seconds; after 0 seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence. OR - Press and HOLD the programming button for seconds. After seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence.

19 LED Diagnostics & Troubleshooting Page 9 LED Description Troubleshooting Module Programming Off Module has no power. Make sure the DD harness is connected or that the Volt is present between the red and black wires. If the Volt is present, the module may be defective. Solid red Waiting to begin the programming sequence. Ensure the correct programming procedure is being followed. & green Solid orange green Initialization failed. Transponder functions were skipped. All required CAN networks has been detected. Reset the module and complete the programming again. If the issue persists, please contact Technical Support. (If compatible) when RXT mode is not desired or convenience features are needed, please reset and reprogram the module. Normal operation. orange orange slowly Solid green x secs of CAN networks has been detected. Normal operation KeyGO initiated. Module was successfully programmed with all functions. Normal operation Please follow the steps indicated in Module programming to complete the KeyGO programming. Solid orange Module was successfully programmed without x secs transponder functions. Module Programming - Error Codes x x x x CAN not detected. J80 not detected. CAN not detected. Bypass data not detected. Normal operation. Check the CAN Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button times. Check the J80 wire connection. Wake up the data bus by turning the ignition on and try again. Check the CAN Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button times. Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure the vehicle still operates correctly using the factory key. x x x 6 x 7 Bypass processing error. ISO not detected. ISO not detected. MUX not detected. The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support. The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections.

20 Page 0 LED Description Troubleshooting External module synchronization (, red then orange) x 0 OBDII feature is not supported. Activation Ground When Running (Status) green Ground When Running (Status) command received. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. The module has initialized the remote start sequence. & orange green quickly x 0 x Commands orange x orange x orange x orange x orange x orange x 6 Ignition ON command received. Start ON command received. PTS shutdown error. CAN bus incorrectly detected. LOCK command received. UNLOCK command received. TRUNK command received. AUX command received. AUX command received. AUX command received. The module has received the Ignition ON command and is processing the remote start sequence. The module has received the Start ON command and is processing the remote start sequence. The PTS output from the module was not activated due to safety protection. Verify the CAN and CAN connections. Refer to Installation (wiring diagrams & vehicle wiring reference charts) to check the connections. If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or DD. Shutdown codes green x x x x x RSR codes x 7 x 9 Takeover successful. Runsafe was not disabled. Brake was not detected. Smart key was not detected. Speed was detected. x OEM Lock Remote Start Activation was attempted when RFTD feature is disabled. Feature error. Normal operation. No UNLOCK command was received prior to opening the door, or the second timer expired in takeover mode. The brakes were not detected, which prevents the system from shutting down the vehicle. The smart key was not detected, which prevents the system from shutting down the vehicle. The vehicle was detected as moving, which prevents the system from shutting it down. Activated from Web automatically when using RSR flash tool or can be done manually. Refer to feature programing section for more information. An RSR feature file mismatch was detected. Please contact Technical Support.

21 Parking Light Error Codes Page The parking lights on your vehicle will flash a specific number of times seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below. Diagnostic Runtime expired. Over-rev shutdown. Low/No RPM. Transmitter shutdown. Brake shutdown. 6 Hood shutdown/remote start safety override switch is ON*. 7 Remote start safety override switch is ON*. * If the vehicle hood status is supported through data, it will also report a 7 flash safety override code.

22 Limited One Year Consumer Warranty Page For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold AS-IS and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED s website at: This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. Protected by U.S. Patents:,79,; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,7,7 B; 6,97,7 B; 6,6,876 B; 6,9, B; 6,9, B; 6,696,97 B; 6,76,88 B; 6,76,886 B; 6,77,67 B; 6,8,89 B; 6,9,70 B; 7,00,0 B; 7,0,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068, B; 7,0,679 B; Cdn. Patent:,0,8;,,99;,,0;,,0;,,07;,,08;,,0;,0,97;,6,670;,,089; European Patent:,0,8; Pat. Pending:,9,06. Made in Canada.

23 Quick Reference Guide DBALL-HYUNDAI Remote Start Ready (RSR) Installation Vehicle Takeover with Get In and Go Note: Takeover feature is not available on the Kia Optima. The engine will stop when a door is opened. GG Pit Stop Mode The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running. Press Press the remote start button on the transmitter to start the vehicle.* remote start button* Stop the vehicle in a safe parking spot and put the gear in Park (P). & P Stop & put vehicle in Park (P) Press the Unlock button on the aftermarket remote.* Press Unlock button* Press the button to remote start the vehicle.* Press remote start button* Enter the vehicle, while making sure the key is inside with you.** Press the brake pedal, put the car in gear and drive off. Ready to drive off HOLD Enter vehicle with Smart Key * Your aftermarket remote may differ from the model shown in the illustrations. ** The vehicle will shutdown if the key is not in the vehicle. It is now safe to leave the engine running and exit the vehicle with the Smart Key in hand. Note: We recommend that you always lock the doors of your vehicle when leaving it unattended. HOLD Exit vehicle with Smart Key * Your aftermarket remote may differ from the model shown in the illustrations. Get In and Go GG Get In and Go is designed to provide users with easy takeover when entering their Push-to-Start (PTS) equipped vehicle, once it has been remote started. Typically, users would have to remote start their vehicle, then get inside and press the vehicle start button to perform a takeover. There is therefore a physical action required to drive away. With Get In and Go technology, you simply remote start the vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and enjoy your vehicle. This unique feature monitors a variety of parameters such as the key fob, vehicle speed sensor and door sensor, in order to perform takeover securily.

24 Quick Reference Guide DBALL-HYUNDAI Remote Start Ready (RSR) Installation Remote Start Ready (RSR) Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. x OEM Lock Remote Start Activation This solution includes the option to remote start your vehicle by pressing the Lock button times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button times once more. List of Available Commands Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information. Button(s) Actions Press & hold for second to lock. Press & hold for second to unlock. Press & hold for second to remote start. Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it. x + x + Press & hold for seconds to activate the trunk release (optional). Press times, then to activate the panic mode. Press once, then to reset the remote starter runtime. * This output is configurable. see your authorized installation center for more information.

25 Quick Reference Guide DBALL-HYUNDAI Remote Start Ready (RSR) Installation SmartStart Compatible Notes This system is compatible with Directed SmartStart.0. For a complete list of supported features, please visit What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system: Ÿ Lock/Arm Ÿ Unlock/Disarm Ÿ Remote Car Starter Ÿ Trunk Release Ÿ Panic Ÿ Aux Channels You can also control multiple vehicles great for families and assign more than one user to control a vehicle. It's easy with SmartStart! But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more..0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of -way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet. For more information, visit