Installation instructions Primor 100

Transcription

1 Content 1 General instructions 2 2 Installation input unit Primor RO 2 3 Installation input unit Primor RE 4 4 Installation lock Primor Connection input unit/lock 9 6 Functional test 9 Carl Wittkopp GmbH - Errors and omissions excepted Installation instructions no

2 1 General instructions Please read the installation instructions carefully, before activating the lock. 1.1 Liability notes The mounting of the electronic lock and the input unit has to be carried out according to the installation instruction. We point out that this installation instruction is part of the VdS-certification and non-compliance leads to the loss of this certification. By opening the lock cover warranty of the manufacturer will be void. Take care that the input unit or the lock and the cables should not be damaged. 2 Installation input unit Primor RO 2.1 Input unit Primor RO Dimensions Primor RO 2.2 Installation overview Input unit Primor RO Fixing ring for input unit Connection axis for turnable input unit 4 Cylinder screws M4 x 10 Connection cable Input unit 2

3 Installation instructions Primor Axis length calculation input unit Primor RO In connection with Primor Door drilling for connection axis Türlochbohrung LL. ø10,6 - max. min. mind Ø 10,6 mm/max. Ø ø11,4 11,4 mm AA L A Türlochbohrung mind. ø9 - max. ø10,6 Connection axis: Debur the ends L = A + 28 mm (tolerance -4 mm) 2.4 Mounting LL==AA++43mm 43mm(Toleranz (Toleranz- -4mm) 4mm) Drill pattern fixing Primor RO L = A + 43mm (Toleranz - 4mm) 4 x Fixing position for M4 Hole center congruent with middle axis of nut of the electronic lock. Opening for cable From the front 4 threaded holes M4 with sufficient depth thread and 1 through-hole (opening for cable/connection axis) have to be drilled into the safe door. From the front the fixing ring has to be fixed with the enclosed cylinder screws M4 x Mounting input unit Primor RO 20 Position 1 Position 2 Position 1: Mount the input unit with an angle of approx. 20 to the fixing ring. Position 2: Turn the input unit to the right into position. The turning has to happen easily. 3

4 2.4.3 Cable guidance Primor RO Plug position Primor RO Plug position Connection axis Lead connection cable through the input unit. Insert the connection axis into the input unit from behind. Lead connection cable through the input unit and connect the plug. 3 Installation input unit Primor RE 3.1 Input unit Primor RE Dimensions Primor RE Installation overview Input unit Primor RE O-Ring axe profile Cylinder screws M5 x 18 Cylinder screws M5 x 14 black covering cap red covering cap Lever 4

5 3.3 Axis length calculation input unit Primor RE In connection with Primor Door drilling for connection axis Türlochbohrung min. mind Ø 10,6. ø10,6 mm/max. - max. Ø ø11,4 mm L Connection axis: Debur the ends L = A + 35 mm (tolerance -2 mm) A Türlochbohrung mind. ø9 - max. ø10,6 3.4 Mounting Drill pattern Primor RE (lock is closing towards the right) - (closing towards the left inversely) Opening for cable Ø 11,4 2 x Fixing position for screws M5 x x Fixing position for screws M5 x From the front 4 threaded holes M5 with sufficient depth thread and 1 through-hole (opening for cable/connection axis) have to be drilled into the safe door Cable guidance Primor RE Plug position Primor RE O-Ring Connection axis retaining washer Lead the connection cable through the connection axis. Plug the connection axis into the lever. Push the cable and the O-ring in the direction of the arrow until the inset. Connect the plug of the cable with the plug on the circuit board. Attention: Don t put the connection cable under tensile stress. Fix the input unit from the front with the enclosed cylinder screws M5. 5

6 4 Installation lock Primor 100 Before mounting the lock the input unit RO or RE has to be installed (see up to page 2). The lock can be installed in all conventional safes. The maximal bolt load against ist closing direction may not excel 5N. Depending on the model there can be optional used more locking elements (e.g. angle with bolts) additional to the existing holes of the bolt. Please make sure that the lock and the connections operate properly. Mind sufficient slackness of the locking point. _The electronic lock has got standard installation dimensions and can be mounted in all installation directions (right-hand, left-hand, upwards, downwards). The electronic lock has to be protected against external attacks. Do not insert any lubricants or other substances into the electronic lock. The electronic lock is maintenance free in normal domestic and office surroundings. After approx. 10,000 closures it is recommended to carry out a security and functional test of the electronic lock. 4.1 Dimensions Dimensions lock Primor Hub/Stroke 12 9,1 66,5 Ø 4,5 Middle-axis of the nut has to be congruent with the middle-axis of the input unit 60,7, mm 22 Platzbedarf/Required space Option extension latch Option lock cover - screwed Ø 6, ,5 6

7 4.1.4 Option lock cover - welded (without anti-drilling plate) Option lock cover - welded (with anti-drilling plate) 112, If the lock is mounted without ist lock case further installation guidelines have to be considered. Non-observance leads to loss of VdS certification. A separate installation instruction can be found on Mounting lock Primor lock cover screwed Dimensions lock Primor lock cover srewed Hub/Stroke , ,5 Ø 6,5 8 Platzbedarf für Riegelhub / Required space for bolt throw 60,7 41,4 142 Ø 4, ,5 3 For fixing the electronic lock 4 threaded holes M6 with depth min. 6 mm (or a comparable inch thread) have to be drilled into the safe door. _Optional: Insert extension latches into the guiding pins at the back of the lock in the right direction and pull up the extensi on latch that closes to the top. The lock case is put on top of the electronic lock. Lead the connection cable of the input unit through the square nut of the lock. Attention: Don t put the connection cable under tensile stress. _Fixing the lock with screws M6 or a comparable inch thread. Length and material application of the screw has to be selected such as a secure long-term stability is guaranteed. _Independent loosening of the screws has to be avoided. Recommendation: put lock washers underneath the screw s head Turn the screws with a maximum turning force of Nm. Mind sufficient slackness of the locking point. 7

8 4.3 Mounting lock Primor lock cover welded Dimensions lock lock cover welded (without anti-drilling plate) Dimensions lock Primor lock cover welded (with anti-drilling plate) Hub/Stroke ,1 8 Hub/Stroke Platzbedarf für Riegelhub / Required space for bolt throw Platzbedarf für Riegelhub / Required space for bolt throw 78 60,7,4 142 Ø 4, ,5 3 78,4 142 Ø 4, , ,5 3 Before welding the lock cover, the lock case has to be removed. _When positioning keep the middle of the connection axis congruent with the input unit RO/RE. _Weld the lock case (if so with hardened manganese steel plate) with 4 welding seams, length -20 mm (position of the welding seams on the corners oft he lock case) to the inside of the safe door. Welding distortion must be avoided. Lead the connection cable of the input unit through the square nut of the lock. Attention: Don t put the connection cable under tensile stress. _The lock then has to be plugged onto the connection axis of the input unit, which is already in the safe door. _Optional: Insert extension latches into the guiding pins at the back of the lock in the right direction and pull up the extension latch that closes to the top. _The electronic lock has to be fixed with the 4 enclosed flat-headed screws M6 x 12 with the designated drillings of the lock case in order that permanent foothold is guaranteed. Turn the screws with a maximum turning force of Nm. After the installation the bolt/extension latches may not be under pressure or strain. 8

9 5 Connection input unit/lock 5.1 Primor 100 Plug position Connect the plug of the input unit with the lock in its designated position. Connect the battery with its clip. Only use 9v block batteries. Keep the cables away from sharp edges and movable components and fix permanently. 6 Functional test (when the door is open) Carry out a functional test after installing the lock and input unit. Enter the factory code Within 3 seconds turn the input unit into the opening position. The lock bolt moves in (has to happen easily). The lock is opened. Turn the input unit into the locking position. The lock bolt moves out and locks. The lock is closed. Keep enough clearance to the locking point.. 9