Pistons and Connecting Rods, Remove and Install
|
|
|
- Sharon Kennedy
- 5 years ago
- Views:
Transcription
1 Page 1 of 46 Pistons and Connecting Rods, Remove and Install Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release the fuel pressure. Important: Fuel may escape observe the safety regulations and relevant national legislation. Release the fuel pressure with the pressure tester KM-J (1) via test connection (2). Collect any escaping fuel in a suitable container.
2 Page 2 of Disconnect the fuel lines. 2 union nuts (1) 2 bolts (2) Reposition the fuel lines (3) to one side.
3 Page 3 of Detach the ignition module (1). Release and detach the wiring harness connector. 4 bolts (2)
4 Page 4 of Remove the cylinder head cover. Detach the engine breather hose (2). Detach the engine lifting eyes (5) and (6). 2 bolts, 1 nut Detach the ground cable (7). 1 bolt 12 bolts (1), (3), (4) and (8) 9. Remove the lower heat shield (1). 3 bolts 10. Detach the upper heat shield (2). 3 bolts 11. Undo the bolts on the rear wheels. 12. Raise the lifting ramp. 13. Detach the rear wheels. 14. Remove the wheel arch trim on the left and right hand side. 12 bolts
5 Page 5 of Disconnect the lambda probe wiring harness connector (2). Expose the wiring harness. 5 clips, 1 retaining clip (1) 16. Raise the lifting ramp.
6 Page 6 of Remove the lower engine splash shield (1). 13 bolts 18. Remove the cover from the exhaust system. 14 bolts
7 Page 7 of Detach the front exhaust pipe. 3 nuts (1) Remove the gasket. 20. Place a drip tray underneath. 21. Drain the coolant. Open the coolant drain plug at the radiator and the coolant pump (1). Tighten the coolant drain plugs. Tightening torque 20 Nm
8 Page 8 of Place a drip tray underneath. 23. Drain the engine oil. Open the oil drain plug. Install the oil drain plug using a new oil seal. Tightening torque 25 Nm 24. Remove the oil pan. 17 bolts Note: Use a suitable tool to evenly prise it off at the leverage points (arrow). 25. Place a drip tray underneath.
9 Page 9 of Align the crankshaft. Rotate the crankshaft in the normal direction of rotation to TDC on cylinder no. 4 (marking 1). Note: In this position the cams of cylinder no. 4 point upwards. 27. Unbolt the camshaft timing chain guide rail. Remove the screw plug (1). 1 bolt (2)
10 Page 10 of Disconnect the wiring harness connector (1) for the tank breather valve (2).
11 Page 11 of Lower the lifting ramp. 30. Remove the exhaust manifold (1). 10 nuts. Remove the gasket (2).
12 Page 12 of Undo the bolts on the oil dipstick guide tube (2). Pull out the oil dipstick (1). 1 bolt (3) 32. Remove the oil dipstick guide tube. Detach the knock sensor wiring harness connector. Pull the oil dipstick guide tube out from the oil pan and take it out to the bottom. 33. Detach the tank breather valve line (1). From the intake manifold. Reposition the line to one side.
13 Page 13 of Drill out the shear bolt (4). Centre punch Pre drill Use a 3 mm drill. Max. depth 10 mm Drill out Use a 6.5 mm drill. Until the head of the bolt comes free. 35. Remove retaining bolt (2). 36. Remove the bridge piece (3). Reposition the ground cable to one
14 Page 14 of 46 side. 37. Remove the retaining bolts (1). 2 bolts 38. Take out the engine control unit. 39. Detach the coolant hoses (1) and (2). 2 off
15 Page 15 of Detach the wiring harness connector (1) from the injectors (2). Release and detach the 4 wiring harness connectors. 41. Detach the MAP sensor wiring harness connector. 42. Detach the throttle body wiring harness connector. Release and detach the wiring harness connector. 43. Detach the wiring harness. 2 clips 44. Disconnect the tank breather line from the
16 Page 16 of 46 intake manifold. 45. Unbolt the exhaust gas recirculation pipe. 2 bolts 46. Detach the wiring harness connector from the exhaust gas recirculation valve. Release and detach the wiring harness connector. Reposition the wiring harness to one side. 47. Undo the bolts on the intake manifold (1). 5 bolts, 2 nuts, 2 studs Lift out the intake manifold. 48. Remove the guide rail (1). 2 bolts (2)
17 Page 17 of Note: If there is no marking (1) on the camshaft timing chain tensioner (2), then it should be replaced with a new camshaft timing chain tensioner (part number ) including a new camshaft timing chain tensioner rail (part number ). 50. Remove the camshaft timing chain tensioner (1).
18 Page 18 of Remove the exhaust camshaft sprocket (1). Hold the exhaust camshaft by the hexagon. 52. Remove the intake camshaft sprocket (2). Hold the exhaust camshaft by the hexagon. 53. Detach the cylinder head. Important: The cylinder head must only be removed when the engine is cold (i.e. at room temperature). 4 Torx bolts and 10 hexagon bolts Note: Undo the bolts in the order shown. Undo the bolts (90 ) Undo the bolts (180 )
19 Page 19 of Remove the cylinder head (1). Note: 2 technicians required Place the cylinder head on wooden blocks. Take off the cylinder head gasket (2). 55. Raise the lifting ramp. 56. Unscrew the bolts on pistons 1 and 4. Attach the rotational vibration damper to the crankshaft, and rotate the crankshaft in the normal direction of rotation until pistons 1 and 4 are at BDC. Mark the connecting rod and big end bearing cap (1). Note: Note the cylinder sequence.
20 Page 20 of Detach the big end bearing caps. 2 off 4 bolts Important: The broken surfaces of the connecting rods and the big end bearing caps form a unique fit and must not be swapped or damaged. Do not put the parts down on the broken surfaces. 58. Press out the piston and connecting rod from the cylinder bore. 59. Lower the lifting ramp. 60. Remove pistons 1 and 4. Take out the pistons and connecting rods. 61. Raise the lifting ramp.
21 Page 21 of Unscrew the bolts on pistons 2 and 3. Rotate the crankshaft via the rotational vibration damper 180 in the normal direction of rotation. Mark the connecting rod and big end bearing cap (1). Note: Note the cylinder sequence. 63. Detach the big end bearing caps. 2 off 4 bolts
22 Page 22 of 46 Important: The broken surfaces of the connecting rods and the big end bearing caps form a unique fit and must not be swapped or damaged. Do not put the parts down on the broken surfaces. 64. Press out the piston and connecting rod from the cylinder bore. 65. Lower the lifting ramp. 66. Remove pistons 2 and 3. Take out the pistons and connecting rods. Note: Clean and visually inspect all components. Measure 67. Take out the big end bearing shells (1) and (2). Note: Note the installation position and allocation. Visually inspect the components.
23 Page 23 of Measure the pistons. Determine the piston diameter with a micrometer. Position the micrometer 90 offset to the piston pin axis and 14.5 mm from the lower edge. 4 off 69. Set up the inside micrometer. Assemble the inside micrometer so that its span is greater than the size of the piston. Attach the dial gauge to the inside micrometer. Adjust the inside micrometer to the size of the piston.
24 Page 24 of Determine the turning point, zero the scale. Note: The turning point of the pointer corresponds to the actual piston size.
25 Page 25 of Measure the cylinder bores. Insert the inside micrometer into the cylinder bores. Measure at three levels (I, II and III), working diagonally in each case (1 to 6).
26 Page 26 of Tip back and forth to determine the turning point of the pointer. The difference between "zero" on the scale and the turning point of the pointer is the obtained running clearance. Make a note of the obtained values. 73. Comparison between specified values and actual values Use the largest value from measurements 1 to 6 as the basis for the wear calculation. Piston size + largest running clearance = cylinder diameter at the measuring
27 Page 27 of 46 point Largest value of a measuring plane smallest value of a measuring plane = ovalness of the cylinder in this measuring plane 74. Dismantle the inside micrometer. Install 75. Insert the big end bearing shells. Into the connecting rods and the big end bearing caps Coat the big end bearing shells with engine oil. 76. Adjust the piston ring gaps on piston 2. First piston ring (rectangular section ring) in position (1) Second piston ring (Napier ring) in position (4) Intermediate ring of the oil scraper ring in position (5), steel band rings of the oil scraper ring in position (2) or (3) 77. Install piston 2. Coat the piston and the cylinder bore with engine oil. Compress the piston rings with a piston ring compressor.
28 Page 28 of 46 Important: The arrow on the piston crown points towards the timing chain end of the engine. Attach KM-J (1) to the connecting rod and slide in the piston. 78. Raise the lifting ramp. 79. Detach KM-J Lower the lifting ramp. 81. Adjust the piston ring gaps on piston 3. First piston ring (rectangular section ring) in position (1) Second piston ring (Napier ring) in position (4) Intermediate ring of the oil scraper ring in position (5), steel band rings of the oil scraper ring in position (2) or (3) 82. Install piston 3. Coat the piston and the cylinder bore with engine oil. Compress the piston rings with a piston ring compressor. Important: The arrow on the piston crown points towards the timing chain end of the engine. Attach KM-J (1) to the connecting rod and slide in the piston. 83. Raise the lifting ramp. 84. Detach KM-J
29 Page 29 of Install big end bearing caps 2 and Coat the big end bearing journals with engine oil. Important: Note the applied markings (1). Renew the bolts. Tightening torque 25 Nm Rotate the crankshaft via the rotational vibration damper 180 in the normal direction of rotation. 87. Lower the lifting ramp.
30 Page 30 of Adjust the piston ring gaps on piston 1. First piston ring (rectangular section ring) in position (1) Second piston ring (Napier ring) in position (4) Intermediate ring of the oil scraper ring in position (5), steel band rings of the oil scraper ring in position (2) or (3) 89. Install piston 1. Coat the piston and the cylinder bore with engine oil. Compress the piston rings with a piston ring compressor. Important: The arrow on the piston crown points towards the timing chain end of the engine. Attach KM-J (1) to the connecting rod and slide in the piston. 90. Raise the lifting ramp. 91. Detach KM-J
31 Page 31 of Lower the lifting ramp. 93. Adjust the piston ring gaps on piston 4. First piston ring (rectangular section ring) in position (1) Second piston ring (Napier ring) in position (4) Intermediate ring of the oil scraper ring in position (5), steel band rings of the oil scraper ring in position (2) or (3) 94. Install piston 4. Coat the piston and the cylinder bore with engine oil. Compress the piston rings with a piston ring compressor. Important: The arrow on the piston crown points towards the timing chain end of the engine. Attach KM-J (1) to the connecting rod and slide in the piston. 95. Raise the lifting ramp. 96. Detach KM-J
32 Page 32 of Install big end bearing caps 1 and Coat the big end bearing journals with engine oil. Important: Note the applied markings (1). Renew the bolts. Tightening torque 25 Nm Clean the sealing surfaces. Cylinder block base plate, oil pan 100. Recut the thread. 15 off
33 Page 33 of Install the oil pan. Apply a bead of silicone sealant (grey) (approx. 2 mmto 2.5 mm (dimension I) thick) at a spacing of 0.5 mm to 1.5 mm (dimension II) from the inner edge of the sealing surface to the sealing surfaces of the oil pan. Apply an additional bead of silicone sealant (grey) (approx. 2 mm to 2.5 mm (dimension I) thick) centrally to the oil intake pipe connection (1).
34 Page 34 of Tighten all bolts loosely. Note: Observe the tightening sequence. To the cylinder block base plate tightening torque 23 Nm To the transmission housing tightening torque 23 Nm
35 Page 35 of Rotate the crankshaft in the normal direction of rotation to TDC on cylinder no. 4 (marking 1) Lower the lifting ramp Install new intake manifold gaskets (1) and (2). 5 off 106. Recut the M8 thread. 4 bolts, 4 bores 107. Clean the sealing surfaces and bores. Cylinder block, cylinder head, front exhaust pipe.
36 Page 36 of Check for plane surface. Cylinder block (II), cylinder head (I) Use a straightedge, feeler gauges
37 Page 37 of Place the cylinder head (1) in place. Note: 2 technicians required Fit a new cylinder head gasket (2). Note: The OBEN / TOP mark must face upwards. When placing the cylinder head on the upper part of the cylinder block, guide the camshaft timing chain up through the timing case, e.g. with a bent piece of electrode wire (to be fabricated by the technician).
38 Page 38 of Attach the cylinder head. Use new cylinder head bolts (hexagon bolts). Note: Observe the tightening sequence. Tightening torque (M10) 30 Nm Coat the M8 bolts with thread locking compound (red) and insert them. Tightening torque 35 Nm 111. Install the intake camshaft sprocket. Use a new bolt. Tighten finger tight Attach KM-6148 to the cylinder head Secure the intake camshaft sprocket. Use the positioning bolt from KM to secure it Fit the camshaft timing chain. Feed the camshaft timing chain by hand through the timing case. Note: The TDC reference points on
39 Page 39 of 46 the timing chain are indicated by coloured links in the chain. These must line up with the markings on the chain links. Chain link (copper colour) (1) to INT marking (2) on the intake camshaft sprocket 115. Install the exhaust camshaft sprocket. Important: Check that the TDC reference points line up. Chain link (1) to EXH marking (2) on the exhaust camshaft sprocket Pull back the positioning bolt from KM Rotate the exhaust camshaft by the hexagon until the exhaust camshaft sprocket is seated in the guide. Use a new bolt Detach KM Tighten the camshaft sprockets.
40 Page 40 of 46 Hold the camshaft by the hexagon. Tightening torque 85 Nm Recut the thread. 2 off 119. Install the guide rail. Coat the bolts with thread locking compound (red) and insert them. Tightening torque 8 Nm 120. Raise the vehicle Attach the camshaft timing chain guide rail. 1 bolt (2) Tightening torque 10 Nm Install the screw plug (1). Tightening torque 65 Nm 122. Lower the vehicle.
41 Page 41 of Install the camshaft timing chain tensioner. Pull out the piston (4) from the housing (1). Clamp the piston at the square into a vice. Turn clockwise to lock the internal piston (6) in the last latch position (5). Insert the piston into the housing. Use new oil seals (2) and (3). Tightening torque 75 Nm
42 Page 42 of Important: Failure to follow this instruction could cause the camshaft timing chain to jump Release the camshaft timing chain tensioner by pressing on the tensioner rail or the camshaft timing chain (using a blunt tool e.g. a rounded assembly lever). Note: If the TDC
43 Page 43 of 46 markings no longer line up with the coloured chain links, refit the camshaft timing chain. Once the crankshaft has been rotated another turn they will no longer line up Raise the lifting ramp Rotate the crankshaft720. Rotate the crankshaft in the normal direction of rotation to TDC on cylinder no. 4 (marking 1). Note: In this position the cams of cylinder no. 4 point upwards Lower the lifting ramp.
44 Page 44 of Attach KM Note: In this position the cams (1) and (2) of cylinder no. 4 point upwards. Attach KM-6148 with the enclosed bolts (4). Slide the positioning bolts (5) into the designated bores (3) on the camshaft sprockets Detach KM Attach the intake manifold. 5 bolts, 2 nuts, 2 studs Tightening torque 9 Nm 132. Route the tank breather valve wiring harness. 1 clip 133. Attach the exhaust gas recirculation pipe. Clean the sealing surfaces. Use a new gasket. Tightening torque 9 Nm Attach the engine cover bracket. Tightening torque 8 Nm 134. Attach the tank breather line Attach the wiring harness Attach the wiring harness connector for the throttle body. Secure the wiring harness connector(s) Attach the MAP sensor wiring harness connector.
45 Page 45 of Attach the injector wiring harness connector. Secure the 4 wiring harness connectors Connect the coolant hoses. 2 off 140. Clean the engine control unit. Clean the engine control unit and the plug contacts with compressed air Install the engine control unit. 2 bolts Tightening torque 9 Nm Attach and secure the wiring harness connector. Note: Check for proper seating and good electrical contact. Attach the bridge piece with a new shear bolt. Route the ground cable. 1 bolt Tightening torque 10 Nm 142. Connect the tank breather valve line. To the intake manifold 143. Insert the oil dipstick guide tube. Use new oil seals. Coat the oil seals with silicone grease (white). Insert the oil dipstick guide tube as far as the stop into the oil pan. Attach the knock sensor wiring harness connector Attach the oil dipstick guide tube. Tightening torque 9 Nm 145. Insert the oil dipstick guide. Use new oil seals. Coat the oil seals with silicone grease (white). Insert the oil dipstick guide tube as far as the stop into the oil pan. Attach the knock sensor wiring harness connector Attach the oil dipstick guide tube. Tightening torque 9 Nm 147. Install the exhaust manifold. Use a new gasket. Use new nuts. Tightening torque 12 Nm Wait for 30 seconds. Tightening torque 12 Nm 148. Raise the lifting ramp Connect the tank breather valve wiring harness connector Attach the front exhaust pipe. Use a new gasket. Tightening torque 16 Nm 151. Attach the cover for the exhaust system. 14 bolts 152. Attach the lower engine splash shield. 13 bolts 153. Connect the lambda probe wiring harness.
46 Page 46 of 46 Route the wiring harness. 5 clips, 1 retaining clip 154. Attach the wheel arch trim on the left and right hand side. 12 bolts 155. Attach the rear wheels Lower the lifting ramp Tighten the rear wheels. Tightening torque 90 Nm 158. Attach the upper heat shield. Attach the engine lifting eye. 1 nut 3 studs Tightening torque 23 Nm 159. Install the lower heat shield. Tightening torque 8 Nm 160. Attach the cylinder head cover Clean the sealing surfaces. Use new gaskets. Note: The sealing lips of the seals (1) must be inserted into the groove on the cylinder head cover. Tightening torque 9 Nm Attach the ground cable Tightening torque 9 Nm Attach the engine lifting eyes. 2 bolts, 1 nut Attach the engine breather hose. Attach the fuel line bracket. Tightening torque 8 Nm 161. Attach the ignition module. Tightening torque 9 Nm Attach and secure the wiring harness connector Connect the fuel lines. Insert the fuel lines into the clip. Tightening torque 10 Nm 163. Fill up with engine oil and check the oil level Fill up with coolant and correct as required Install the rear engine cover. Check the alignment. 6 bolts, tightening torque 14 Nm 166. Close the rear engine cover Connect the battery Close the bonnet Reprogram the volatile memories.
Cylinder Head, Remove and Install (Z 22 SE)
Page 1 of 29 Cylinder Head, Remove and Install (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release the
Timing Chain, Balancer Shaft, Replace (Z 22 SE)
Page 1 of 34 Timing Chain, Balancer Shaft, Replace (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release
Crankshaft, Remove and Install (Engine Removed) (Z 22 SE)
Page 1 of 36 Crankshaft, Remove and Install (Engine Removed) (Z 22 SE) Remove 1. Remove the engine Note: See operation "Engine, Remove and Install". 2. Separate the manual transmission from the engine.
Valve Timing, Adjust (Z 22 SE)
Page 1 of 15 Valve Timing, Adjust (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release the fuel pressure.
Coolant Pump, Remove and Install (Z 22 SE)
Page 1 of 10 Coolant Pump, Remove and Install (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the rear engine cover (1). 4. Detach the rear engine cover. 6 bolts (2) and (3) 5.
Engine Dismantle and Assemble ( )
Engine Dismantle and Assemble ( 34 8) Special Tools 5 053 Slide hammer 47 Vibration damper remover 47 5053 00 Splined head socket, cylinder head bolts 87 Mounting stand with geared drive 00 059C Installer
Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13)
13 Engine-Crankshaft, Cylinder block (Page GR-13) Engine, disassembly and assembly 10-222 A/21 guide from 10-222 A support tool, modifying Ribbed belt, removing and installing Semi-automatic toothed belt
Engine Dismantle and Assemble ( )
Engine Dismantle and Assemble (2 34 8) Special Tools 2-036A Remover for pilot bearing 2-37 Oil seal installer/aligner 237 2036A 2-044A Installer/Aligner, Pilot Bearing/Clutch Plate 244 2-44 Inlet manifold
Torque Guidelines (Z 22 SE)
Page 1 of 14 Torque Guidelines (Z 22 SE) No. Designation Nm 1 Retaining bolts, coolant pump sprocket to coolant pump 2 Retaining bolts, balancer shaft timing chain guide rail to 3 Retaining bolts, balancer
Removing and installing timing case cover. A. Engine
01-2100 Removing and installing timing case cover Operation no. of operation texts and work units or standard texts and flat rates 01-0080, 8009 A. Engine 119.960 Viscous fan clutch remove, install (20-3120).
Engine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D)
SECTION 303-01A: Engine 4.0L SOHC 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 05/10/2010 Engine Special Tool(s) Adapter for 303-564 303-578 (T97T-6256-A) Adapter for 303-577 303-576
1989 BMW 635CSi. 3.5L 6-CYL Engine - 3.5L 6-Cylinder
Fig. 3: Rocker Arm Assembly Courtesy of BMW OF NORTH AMERICA, INC. VALVE SPRINGS NOTE: Install springs with paint stripe (tight coil end) against head. Inspection Check spring free length. Check spring
ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)
303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket
Engine Dismantle and Assemble ( )
Engine Dismantle and Assemble (21 134 8) Special Tools 15-030A Universal flange-holding wrench 21147 21-147 Vibration damper remover 15030A 16-067 Locator for clutch disc 21-167 Wrench for cylinder head
1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder
ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION
AJV8 Engine Assembly. AJV8 Engine Assembly
AJV8 Engine Assembly Contents Cylinder Block Dowels, Plugs and Pipes 2 4 Crankshaft Bearing and Cylinder Bore Dimensions 5 9 Bearing Measuring 6 Engine Dimensions and Codes 6 7 Main Bearing Selection Chart
2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
Removing and installing cylinder head
31 30 29 28 27 26 25 24 23 22 1 2 3 11 12 10 4 9 5 6 7 8 Removing and installing cylinder head Checking compression pressure page 15-24. Notes: When installing a replacement cylinder head with a mounted
Valve gear, servicing
Page 1 of 62 15-1 Valve gear, servicing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once, and are unreliable and may fail if
Timing Chain - Renew ( )
«Escort 1991/1996 Table of Contents» «Group 21: Basic Engine» «Section 21-09: 2.0l DOHC 16V Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 15-030 AUniversal flange holding
DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
1995 Aerostar/Ranger/Explorer
Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,
Sealing flanges and flywheel/drive plate, removing and installing
Page 1 of 20 13-47 Sealing flanges and flywheel/drive plate, removing and installing Note: For repairs to the clutch: Repair Manual, 5 Spd. Manual Transmission 012/01W Front Wheel Drive, Repair Group 30
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS
connecting rods are marked for reassembly. 3. Thoroughly clean and inspect all components. Coat pin with engine oil and heat piston to 158-176 F (70-80 C). Pin should push fit with thumb pressure through
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT
ASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
Removing and installing toothed belt
Page 1 of 10 Special tools and workshop equipment required Diesel injection pump locking pin -3359- (2x) Pin wrench -T10020- Crankshaft stop -T10050- for engines with circular crankshaft sprocket Locking
Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
1.6L 4-CYL - VIN [E]
![1.6L 4-CYL - VIN [E]](/thumbs/81/84172348.jpg "1.6L 4-CYL - VIN [E]")
1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES
Camshaft - Remove and Install ( )
«Escort 1991/1996 Table of Contents» «Group 21: Basic Engine» «Section 21-09: 2.0l DOHC 16V Engine» «REMOVAL AND INSTALLATION» Camshaft - Remove and Install (21 283 0) Special Tools 15-030 AUniversal flange
DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX)
2012 Cadillac CTS Wagon AWD V6-3.0L Vehicle > Engine, Cooling and Exhaust > Engine > Locations > Components DISASSEMBLED VIEWS Disassembled Views Engine Covers and Component Assemblies (1 of 2) (LF1, LFW
Lower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
General Specifications
General Specifications Engine Data Description Litres Engine management EEC V/SFI Emission standard 96 EEC Engine code NSD Firing order 1-3 - 4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cm 3 1998 Compression
Cylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
1990 Buick Electra Limited
4. To install remaining components, reverse removal procedure. Coat rocker arm bolts with GM Threadlock (12345493) prior to installation. Fig. 3: Cylinder Head Bolt Tightening Sequence FRONT CRANKSHAFT
TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump SERVICE DATE MODEL 2002 MY.
SERVICE V8 XJ Series DATE 12/02 TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump 100-21 MODEL 2002 MY V8 XJ Series VIN F44114 - F55936 Issue: Some 2002
IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
AR01.30-P-5800PK Remove/install cylinder head
Page 1 of 10 AR01.30-P-5800PK Remove/install cylinder head 7.6.00 ENGINE 111.955 in MODEL 203.045 /245 /745 P01.30-2081-09 1 Air filter housing 2 Air recirculation flap actuator 3 Top engine trim panels
Testing and Inspection. Diagnostic Procedure Step 1-2
1 of 4 5/22/2008 7:54 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Nissan-Datsun Altima 2.5 S L4-2.5L (QR25DE) Vehicle
SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking
D8 - Distributor. D9 - Auxiliary unit belts
D8 - Distributor l ubricate Lubricate the distributor shaft sparingly (1-2 drops of oil) D9 - Auxiliary unit belts check/adjust Applies to engines which do not have multi-tooth belts Check belt tension.
2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper
Valvetrain, servicing
Page 1 of 51 15-32 Valvetrain, servicing Note: Cylinder heads with small cracks between the valve seats that are less than 0.3 mm (0.012 in.) wide and/or between one valve seat and only the first 4 threads
NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B.
8 CORRECT Adjusting Bar 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT Generator Vehicle Front A077960E03 INSTALLATION 1. INSTALL VANE PUMP V BELT (a) Temporarily install the belt on each pulley. 2. INSTALL
Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar
Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer
Timing Chain Renew ( )
Timing Chain Renew (1 314 0) Special Tools 1 137 Oil seal installer/aligner, crankshaft front 1168 1 168 Crankshaft immobilising tool 1137 1 140 Engine support bar 4 003 Remover/installer, radiator hose
IN-VEHICLE SERVICE. Engine Components
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown
Timing Chain - Renew ( )
«Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140
ALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair
Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special
2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
Intake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
DISASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
TEST AND ADJUSTMENT Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking (Minimum).......................... 28 kpa (4 psi) Oil Pressure.....................................
1992 Toyota Cressida
Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May
Exhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove
1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release
Service 5. Workshop Manual FABIA /55; 1.4/74 Engine - Mechanical Components Edition Service Department. Technical Information
Service 5 Workshop Manual FABIA 2000 1.4/55; 1.4/74 Engine - Mechanical Components Edition 08.99 Engine code AUA AUB BBY BBZ BKY Service Department. Technical Information Printed in Czech Republic S00.5306.00.20
1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder
Removal & Installation See VALVE SPRINGS under CYLINDER HEAD under OVERHAUL. CAMSHAFT Removal 1. Rotate crankshaft until "0" mark on flywheel aligns with timing mark on flywheel cover. Remove inspection
Page 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft
Toothed belt, removing and installing
Toothed belt, removing and installing Special Tools and Equipment ^ 3212 spanner wrench ^ 3387 pin wrench ^ T40011 pin ^ T40026 locking pin ^ T40028 socket ^ T40030 camshaft adjuster gauge Removing Lock
ENGINE MECHANICAL EM SECTION CONTENTS
ENGINE MECHANICAL EM SECTION CONTENTS INTAKE MANIFOLD...EM-2 Component Parts Location...EM-2 Removal and Installation...EM-3 Inspection...EM-3 EXHAUST MANIFOLD...EM-4 Component Parts Location...EM-4 Removal
General Specifications
General Specifications Engine Data General Engine management EEC V/SEFI Emission standard 96 EEC Engine code N3A Firing order 1-3-4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cc 1998 Compression ratio
1999 Acura SLX. Fig. 6: Identifying Piston & Connecting Rod Size Courtesy of ISUZU MOTOR CO.
3. Check cylinder bore to determine piston-to-cylinder clearance. Clearance should be within specification. See PISTONS, PIN & RINGS table under ENGINE SPECIFICATIONS. Fig. 6: Identifying Piston & Connecting
DISASSEMBLY AND REASSEMBLY
24 01 DISASSEMBLY AND REASSEMBLY COMPONENTS AND SPECIAL TOOLS Injector Puller Y99220072B Glow Plug Wrench Y99220132B Fuel Pipe Wrench Sealing Caps 665 995 5844 Injector Copper Washer Puller Y99220022B
Page 1 of 5 Section 03-01C: Engine, 4.0L V-6 IN-VEHICLE SERVICE Workshop Manual Camshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Sensor Adjusting Wrench T94T-12270-A Removal NOTE: It is
1999 Honda Accord DX
Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are
FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G )
PUBLISHED: 10-OCT-2017 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G1473741) GENERAL PROCEDURES 19.90.17 HIGH PRESSURE FUEL TIMING CHECK AND
OVERHAULING THE ENGINE. 85 Nm (8.5 m kg, 61 ft Ib) Order Job/Part Q ty Remarks Removing the drive sprocket
INE EAS00188 INE DRIVE SPROCKET OVERHAULING THE INE 10 Nm (1.0 m kg, 7.2 ft Ib) 85 Nm (8.5 m kg, 61 ft Ib) Order Job/Part Q ty Remarks Removing the drive sprocket Remove the parts in the order listed.
6 cylinder turbocharged diesel engines for industrial applications
Perkins 2800 Models 2806C-E16 WORKSHOP MANUAL 6 cylinder turbocharged diesel engines for industrial applications Publication TSD3450E, Issue 1 Proprietary information of Perkins Engines Company Limited,
Service and Repair CAMSHAFT
Service and Repair CAMSHAFT Removal and Installation REMOVAL 1. Remove front timing chain case, camshaft sprocket, timing chain and rear timing chain case. Refer to "REMOVAL". 2. Remove camshaft position
Cylinder Heads Remove and Install (all) ( ) Remove. 2,5l TCI Diesel Engine. Special Tools Bolt tightening angle gauge
Cylinder Heads Remove and Install (all) ( 64 0) Special Tools 00 00 00 Splined head socket, cylinder head bolts 00 Cylinder head locating studs 540 04 540 Bolt tightening angle gauge 04 Wrench for injectors
The following tools will be required to perform this new service procedure outlined in this bulletin:
The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure
VALVE CLEARANCE (K3-VE)
ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT
2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)
Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with
2.4L 4-CYL - VINS [F,H,S]
![2.4L 4-CYL - VINS [F,H,S]](/thumbs/72/66412829.jpg "2.4L 4-CYL - VINS [F,H,S]")
2.4L 4-CYL - VINS [F,H,S] 1990 Nissan 240SX 1990 ENGINES Nissan 2.4L 4-Cylinder Axxess, Pickup, Stanza, 240SX * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article,
Fuel and exhaust systems 4A 21
Fuel and exhaust systems 4A 21 15.40 Unscrew the union nuts and disconnect the fuel feed and return hoses from the manifold 41 Disconnect the injector wiring harness connector and the vacuum hose from
SECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing.
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. ST 499817100 ENGINE STAND Apply a coat of engine oil to the bearing and
DISASSEMBLY. Engine. Special Tool(s) Locking Tool, Camshaft Phaser Sprocket Special Tool(s)
303-01B-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Rear Slinger 303-514 (T95P-6701-AH) Special Tool(s) 303-01B-1 Locking Tool, Camshaft Phaser Sprocket 303-1046 Remover, Crankshaft Rear Seal
FUEL PUMP CAMSHAFT TIMING CHECK
PUBLISHED: 26-FEB-2018 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING CHECK (G1473740) GENERAL PROCEDURES 19.90.16 HIGH PRESSURE FUEL TIMING CHECK 5000 CC,
Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
SECTION A Engine 3.7L
303-01A-i Engine 3.7L 303-01A-i SECTION 303-01A Engine 3.7L CONTENTS PAGE SPECIFICATIONS... 303-01A-2 303-01A-2 Engine 3.7L 303-01A-2 SPECIFICATIONS Material Motorcraft High Performance Engine RTV Silicone
Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
Engine, disassembling and
Page 1 of 38 13-1 Engine, disassembling and assembling Lock carrier, moving into service position Special tools and equipment 3369 support tool 1 - Bolts 2 - Bolts 3 - Bolts 4 - Bolts 5 - Bore 45 Nm (33
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Procedures» Removal Cylinder Heads http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=376&nonstandardid=682956&vehicleid=45317&windowname=maina
2nd Timing Chain and Chain Tensioner Components S6RW0C
8) Install cylinder head cover referring to Cylinder Head Cover Removal and Installation. 9) Install oil pan. Refer to Oil Pan and Oil Pump Strainer Removal and Installation in Section 1E for 10) Install
ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)
ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pressure and oil pressure switch, checking Sump, removing and installing Valve gear, servicing (Page
9/24/2017 Camshaft Timing Chain Removal and Installation Engine Mechanical 2002 Audi A6/S6/Quattro/Allroad MotoLogic
2002 A6/S6/Quattro/Allroad The information in this article comes from a service manual containing information that applies to the following engine code: BAS. Section Info: Report a problem with this article
1999 Nissan Altima GLE
TIMING CHAIN CAUTION: If cylinder head is installed and timing chain is disconnected, DO NOT rotate camshaft or crankshaft; valves will contact pistons, resulting in bent valves. NOTE: Following procedure
ENGINE OVERHAUL <2.4L ENGINE>
11D-1 GROUP 11D ENGINE OVERHAUL CONTENTS GENERAL SPECIFICATIONS 11D-2 SERVICE SPECIFICATIONS 11D-2 REWORK DIMENSIONS 11D-3 TORQUE SPECIFICATIONS 11D-4 SEALANTS 11D-7 SPECIAL TOOLS 11D-8 GENERATOR
Chapter 5 Part B: Ignition system - transistorised type
5B 1 Chapter 5 Part B: Ignition system - transistorised type Contents Coil - testing........................................... 9 Distributor - overhaul..................................... 7 Distributor
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
14218 ENGINE MECHANICAL PARTIAL ENGINE ASSY (2ZZGE) OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 140R901 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
Engine Cylinder Head Installation
Engine Cylinder Head Installation Important: Install the cylinder head without the camshafts. 1. Install the engine cylinder head to the engine block. 2. Install the AIR pump bolt and fir tree fastener