Lateral Hip Support INSTALLATION & SET-UP MANUAL. (with Fixed or Removable Hardware) Lateral Hip Support- Fixed Assembly
|
|
- Eleanore Bradford
- 5 years ago
- Views:
Transcription
1 Lateral Hip Support (with Fixed or Removable Hardware) Lateral Hip Support- Fixed Assembly Lateral Hip Support- Removable Assembly (Note: assemblies diagrams are shown for left side only) INSTALLATION & SET-UP MANUAL TRD
2 - 2 -
3 Overview Drawing Lateral Hip Support Assembly
4 Installation & Adjustment Note: The following instructions show installation on the left-hand side of the chair; repeat all steps indicated to complete the right side Hip Support installation. Please read through the entire instruction manual before proceeding with the installation. Lateral Hip Support Installation & Adjustment With the client seated in the chair, determine (approximate) the most desirable fore & aft mounting location for the Lateral Hip Support and select the nearest (existing) mounting holes the seat side frame. (note: the mounting bracket for the Hip Support is typically installed around the center of the seat side frame; Further height and depth adjustments are available via the upright bar and the hip pad). Please refer to Figure 2.0 for detailed adjustment options. 1. With the mounting position determined, use the hardware provided to install the mounting bracket onto the seat side frame. Refer to Step A. in Figure 1.0 below. (note: the seat may need to be tilted to access the underside of the seat side frame). 2. With the mounting bracket installed, slide the upright plate into the slot of the mounting bracket and adjust the height of the plate to establish the final hip pad height. Install the stop bar (see Figure 1.0- Step B. below) onto upright plate at the mounting hole position that comes closest to the achieving the desired overall height. (note: lower plate adjustments are available in 5/8 increments- refer to Figure 2.0). Figure 1.0 Lateral Hip Support Installation hip pad (8 x 3-1/2 ) C Step C: Using the available height and depth adjustments- install the hip pad onto the upright plate using the hardware provided upright plate B stop bar mounting bracket Step B: Adjust the upright plate to the desired position (height) and fasten the stop bar to the plate. A Step A: Secure the mounting bracket onto seat frame using the hardware provided set-screw (for fixed support) hand-wheel lock (for removable support upgrade)
5 Installation & Adjustment PLEASE NOTE: There are 4 optional lateral hip pads sizes available; the height adjustment remains common for all pad sizes, however, the for/aft adjustment can vary depending on the style of pad selected. Please refer to Figure 2.0 below for details on the various pad options and adjustments. 3. Before completing the installation- determine the final height and fore/ aft position (depth) of the lateral hip pad relative to the upright plate: i) The hip pad can be installed onto the upright plate at one of two height positions- see Important note below. (note: A maximum 1/2 of height adjustment is available via the plate). ii) The fore/aft adjustment of the hip pad will vary depending on the selected pad style- see Figure 2.0 below. (note: fore/aft adjustments are available in increments along the length of the hip pad). Once the final mounting position has been chosen, secure the Lateral Hip Pad onto the upright plate using the hardware provided- refer to Figure 1.0- Step C.) Important! - all four (4) mounting screws (provided) must be used to secure the hip pad onto the plate; if the overall height or depth cannot be achieved via the adjustment in the hip pad, then adjustments must be made via the stop bar or the mounting bracket. 4. Secure the Lateral Hip Support Assembly into place on the seating system: i) for fixed hip supports: tighten the set-screw in the mounting bracket until it is snug up against the upright plate (refer to Figure 1.0). ii) for removable hip supports: tighten the hand-wheel lock in the mounting bracket until it is snug up against the upright plate (refer to Figure 1.0). Figure 2.0 Lateral Hip Support Adjustments (left side shown) total adjustment range of 3 Hip Pads (4 sizes available) 1/2 height adjustment (2 positions) { { nonadjustable 8 W x 3-1/2 H 3-1/2 W x 4-1/2 H upright plate total adjustment range of 3 5/8 increments stop bar total adjustment range of 1-7/8 6 W x 5 H total adjustment range of 3 mounting bracket 12 W x 3-1/2 H
6 84 Citation Drive, Units 1-7, Concord, Ontario, Canada L4K 3C1 Toll Free Tel: Fax: Ensminger Rd. Suite 112, Tonawanda, New York, USA Toll Free Tel: Toll Free Fax:
i NOTE: This installation manual contains important set-up and adjustment information. Please forward to the Dealer, together with the TRx system, in
Multi-Axis Armrest Mount Installation & Set-Up Manual i NOTE: This installation manual contains important set-up and adjustment information. Please forward to the Dealer, together with the TRx system,
More informationSupport Harness Mounting Bracket Assembly for the
Support Harness Mounting Bracket Assembly for the Matrx PB and Matrx Elite Back Cushion Installation & Set-up Manual DEALER: This manual contains important Safety, Installation and Set-up information specific
More informationInstallation and Set-Up Manual
MAXX PIVOT PLUS LEGREST (for Manual and Power Legrest Models) Installation and Set-Up Manual NOTE: This manual contains important information related to the installation, set-up and adjustment of our Maxx
More information- 3 - Important! Note: Before proceeding with the installation/ set-up, please ensure that no pages are missing from this manual.
Centermount Extending Articulating (CMX) Legrest Installation, Set-Up & Adjustment User Manual TRD0272- CMX Legrest Set-Up/ Adjustment Manual, Rev 2.1- February 5, 2010 - 2 - - 3 - i Important! The most
More informationi NOTE: This installation manual contains important information related to set-up
TRx Heavy-Duty Swing Away Legrests Installation and Set-Up Manual i NOTE: This installation manual contains important information related to set-up and adjustments. Please forward to the Dealer, together
More informationMatrx Back Interface for the
Matrx Back Interface for the Quantum Tru-Balance 3 Seating System Installation Instructions TRD0357, Rev A Important Symbols in this Manual Setting up and operating your wheelchair safely depends on your
More informationATTENTION DEALERS i Important Information on Tilt Actuator Warranty Claims: Dealers must contact our Technical Service Department prior to installing
Installation/ Replacement Instructions for the Ultra-Low CG Tilt and Recline s ATTENTION DEALERS i Important Information on Tilt Warranty Claims: Dealers must contact our Technical Service Department prior
More informationMaxx LNX Power Center Mount Legrest
Maxx LNX Power Center Mount Legrest Installation, Set-Up & Adjustment TRD0341 Rev A - 2 - - 3 - Important! The most important link in the delivery chain is the end user. The user must be satisfied with
More informationInstallation and Set-Up Manual
MAXX LNX Power Center Mount Legrest Installation and Set-Up Manual NOTE: This manual contains important information related to the installation, set-up and adjustment of our Maxx Pivot Plus Legrests. Please
More informationMx1 SuperLite Mount. Back Cushion. Installation/User Manual
Mx1 SuperLite Mount Back Cushion Installation/User Manual DEALER: This manual contains important safety, Installation and Set-up information specific to the Invacare Matrx Mx1 SuperLite Mount Back. This
More informationRETRACTED SIDE MINIMUM. 4 1/4 in. [108.0 mm] CP-493 HANGER (WITHOUT TRIGGER) RETRACTED SIDE CP-007 CLIP ACTIVATED SIDE MINIMUM. [108.
TYPE CC-NRB CATCH N CLOSE CROWDERFRAME POCKET DOOR KIT INSTRUCTION SHEET FOR NARROW DOORS 18 in [457 mm] TO LESS THAN 26 in [660 mm] WIDE ONLY ACTIVATED SIDE CC-493 HANGER (WITH TRIGGER) SEE RIGHT (COMPLETE
More informationREVERSIBLE OUTER COVER: >PELVIC OBLIQUITY KIT
POSTURE SEAT MaTRx PS cushion is designed to provide superior positioning, stability and comfort. The design features an anatomically contoured shape with a unique waffled ischial relief recess, and an
More informationHealthy Care High Chair
Healthy Care High Chair Product features and decoration may vary from the photo above. Model Number: 79638, 79639, 79640, 79641, B2875 Please keep this instruction sheet for future reference, as it contains
More informationTYPE CC-W CATCH N CLOSE CROWDERFRAME POCKET DOOR KIT INSTRUCTION SHEET FOR DOORS 26 in [660 mm] TO 48 in [1219 mm] WIDE ONLY
TYPE CC-W CATCH N CLOSE CROWDERFRAME POCKET DOOR KIT INSTRUCTION SHEET FOR DOORS 26 in [660 mm] TO 48 in [1219 mm] WIDE ONLY (COMPLETE TYPE CC-W KIT ILLUSTRATED. FRAMING BY OTHERS) CATCH N CLOSE TM CROWDERFRAME
More informationTitan Articulating Arm Dual Media Cart INSTALLATION INSTRUCTIONS. Page 1
Titan Articulating Arm Dual Media Cart INSTALLATION INSTRUCTIONS Page 1 INSTRUCTIONS CLEARONE DOCUMENT 800-300-025-01 (REVISION 2.0) February 2013. TITAN DUAL ARTICULATING ARM MEDIA CART The Titan Dual
More informationGives useful tips, recommendations and information for efficient, trouble-free use.
User Manual DEALER: This manual MUST be given to the user of the product. USER: BEFORE using this product, read this manual and save for future reference. Invacare Matrx PB 1 General 1.1 Symbols Signal
More informationRemote Display Mounting Assembly Instructions This manual covers the various mounting options for the Remote Display.
Remote Display Mounting Assembly Instructions This manual covers the various mounting options for the Remote Display. Instructions suitable for these Remote Displays 046D-602-110 Table of Contents 1. INTRODUCTION...1
More informationUser Manual. Invacare Matrx Genera Back. Model Number GB. 1 General
User Manual DEALER: This manual MUST be given to the user of the product. USER: BEFORE using this product, read this manual and save for future reference. Invacare Matrx Genera Back Model Number GB 1 General
More informationKidWalk KidWalk II Dynamic Mobility System
OWNER S MANUAL KidWalk KidWalk II Dynamic Mobility System Manufactured By Prime Engineering A Division of Axiom Industries, Inc. Supplier Info 70111KWOM 2 TABLE OF CONTENTS This owner s manual is organized
More informationCP-TK-2X4 POCKET TRIM KIT INSTRUCTION SHEET
CP-TK-2X4 POCKET TRIM KIT INSTRUCTION SHEET (COMPLETE TYPE CC-W KIT WITH CP-TK-2X4 TRIM KIT ILLUSTRATED) POCKET TRIM KIT POCKET TRIM KIT (CP-TK) SAVES ON INSTALLATION TIME, EASY TO INSTALL AND MAKES EASY
More informationELITE HEAVY-DUTY BACK
WARRANTY Every Matrx Elite HD back is carefully inspected and tested to provide optimum performance. Each back is guaranteed to be free from defects for a period of 24 months from the date of purchase,
More informationINSTALLATION/USERS MANUAL
INSTALLATION/USERS MANUAL ! IMPORTANT: The installation and set up instructions should be carried out by a qualified technician. IMPORTANT: It is important to refer to the wheelchair owner s manual for
More informationInstallation Instructions for Foam Marker ZMAX
2017 Installation Instructions for Foam Marker ZMAX We appreciate your purchase of L.T. Rich s Product. Please Verify Contents before beginning installation. JLD;AES L.T.RICH 5/2/2017 SHIPPING CONTENTS...
More informationHOW TO RELEASE/ REATTACH BACK SUPPORT ACTUATOR AND GAS SPRING
Welcome to the quick reference guide for the Quickie SmartSeat. This guide was created to assist you in the set-up of your SmartSeat.The Quickie SmartSeat with Intelli-motion represents a breakthrough
More informationInstallation Instructions for Foam Marker INTERMEDIATE also applies: JR, JR36
2017 Installation Instructions for Foam Marker INTERMEDIATE also applies: JR, JR36 We appreciate your purchase of L.T. Rich s Product. Please Verify Contents before beginning installation. JLD;AES L.T.RICH
More informationINFINITY MULTA SERIES
ASSEMBLY ASSEMBLY INSTRUCTIONS INSTRUCTIONS ASSEMBLY INSTRUCTIONS INFINITY MULTA SERIES Workstations, WORKSTATIONS, desks, DESKS, and AND tables TABLES with WITH powered POWERED ADJUSTMENT adjustment PARTS
More informationINSTALLATION INSTRUCTIONS JEEP WRANGLER PART# 1050 /
INSTALLATION INSTRUCTIONS 2007-12 JEEP WRANGLER PART# 1050 / 1050-2 PARTS LIST: Qty Description Qty Description 1 Aries Grill guard 10 12mm Lock washers 1 Driver/left mounting bracket 10 12mm Hex nuts
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500 REGULAR CAB REGULAR CAB
INSTALLATION INSTRUCTIONS PARTS LIST: 2 Steel Running Boards 3 12mm Hex Nuts 1 Driver/Left Mounting Bracket 4 10-1.5mm x 35mm Hex Bolts 1 Driver/Left Support Bracket 4 10mm x 27mm OD x 3mm Flat Washers
More informationRodeo Upgrades Q2 2014
Rodeo Upgrades Q2 2014 New Rodeo Convaid is excited to announce new standard features and accessory options on the Rodeo Tiltin-Space Wheelchair. All new orders received as of June 19 2014 will have all
More informationTyler - Cargo Rack For Eurocopter AS-350 & AS-355 Series Helicopters FAA STC # SR01449LA
Cargo Rack A-Star / Twinstar Installation Manual Tyler - Cargo Rack For Eurocopter AS-350 & AS-355 Series Helicopters FAA STC # SR01449LA PLEASE return THIS MANUAL with equipment This manual is available
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500/ CREW CAB
INSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS PARTS LIST: 1 Driver/Left Steel Running Boards 5 12mm Lock Washers 1 Passenger/Right Steel Running Boards 5 12mm Hex Nuts 1 Driver/Left Mounting Bracket
More informationQuick Release Mounting Hardware
Mounting Hardware USER MANUAL Quick Release Mounting Hardware Stealth s User Manual and Maintenance Guide for ADI s Quick Release Mounting Hardware Customer Satisfaction 1.0 Stealth Products strives for
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500 QUAD CAB
INSTALLATION INSTRUCTIONS PARTS LIST: 2 Steel Running Boards 5 12mm Lock Washers 1 Driver/Left Mounting Bracket 5 12mm Hex Nuts 1 Driver/Left Center Mounting Bracket 6 10-1.5mm x 35mm Hex Bolts 2 Driver/Left
More informationLankota, INC. LAN Installation Instructions
Lankota, INC. LAN - 84206 Converts 600 Series Platform Heads to 50 Series & Earlier Model Combines. Installation Instructions Kit LAN84206 Lankota is the trademark of Lankota, Inc. 1 LAN 84206 Parts break
More informationINSTALLATION INSTRUCTIONS PART#: SR-GMR13796 SPARTAN RUNNING BOARD CHEVY EXPRESS 1500/2500/3500 GMC SAVANNA 1500/2500/ UP
INSTALLATION INSTRUCTIONS PART#: SR-GMR13796 SPARTAN RUNNING BOARD CHEVY EXPRESS 1500/2500/3500 GMC SAVANNA 1500/2500/3500 03-UP PARTS LIST: 1 Driver Side- 37 Spartan Running Board 8 12mm Hex Nuts 1 Passenger
More informationSingle-Sided Storage Rack Assembly Instructions
Single-Sided Storage Rack Assembly Instructions H D I G J K M L F I D B C A E PART NAME QTY A. BASE BAR (50 ) 2 B. BASE BAR HULL GUARD (34 ) 2 C. BASE BAR END CAP 2 D. SAFETY END CAP 4 E. FOOT 4 F. UPRIGHT
More informationP3066 INSTALLATION MANUAL
P3066 INSTALLATION MANUAL Parts List 1 Grille guard 1 Driver / left frame bracket Level of Difficulty Moderate Scan for helpful install tips 1 Passenger / right frame bracket 1 Driver / left top bracket
More informationAn innovative child safety seat designed for children with special health needs. Listening to therapists working with families
An innovative child safety seat designed for children with special health needs Listening to therapists working with families Features EZ-Up Cap Three sizes available EZ-Up Head Rest Cover Incontinent
More informationlifetime limited warranty
lifetime limited warranty Limited lifetime warranty on frame and cross braces One year limited warranty on other components Your Drive brand product is warranted to be free of defects in materials and
More informationTEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: SR-FOR SPARTAN RUNNING BOARD FORD ECONOLINE 99-14
TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: SR-FOR203796 SPARTAN RUNNING BOARD FORD ECONOLINE 99-14 PARTS LIST: 1 Driver/Left Side Spartan Running Board 2 10mm Lock Washers 1 Passenger/Right Side
More informationINSTRUCTION MANUAL & PARTS BOOK. Vibratory Screed
INSTRUCTION MANUAL & PARTS BOOK Vibratory Screed 200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-5400 FAX 732-5444 Doc. # OI-M09201 Current Rev. 07 Revised: 11/2013 Orig. Rel.: 06/2014 SAFETY
More informationTOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.
TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support
More informationTDX 2 Ultra featuring
Ultimate Control. Ultimate Comfort. The Invacare TDX2 Ultra is an elite, high performance, centre wheel drive power wheelchair equipped with the advanced Ultra Low Maxx seating system. Designed to be the
More informationSubject: Align-Trac Procedures. Lit No: LIT1004 Date: 05/30/2015 Revision: A
Watson & Chalin recently announced the addition of the new Align-Trac trailing arm-to-hanger pivot connection for trailer air suspensions. This Technical Bulletin outlines the procedure to align the axle
More informationK710 Product Manual. Support Station. K710 Product Manual
K710 Product Manual Support Station K710 Product Manual Contents Important information 2 Safety messages 3 Recommended use 4 Item dimensions 5 Check your order 6 Installation 6 Basic components 7 Accessories
More informationUNPACK AND IDENTIFY THE FOLLOWING PARTS.
SUT-500-S ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. *Check all lights before towing. *Tire pressure not to exceed recommendation on serial tag. *Re-torque wheel nuts after first
More information4 DOOR SYSTEM ROOMFOLD DELUXE RANGE
ROOMFOLD DELUXE RANGE 3+1 Pattern 4 DOOR SYSTEM SYSTEM OVERVIEW 818 Top 605 Hanger 125 EQUAL Slave Daily Access 282HSS EQUAL Flush bolt on reverse side of door 150 802 Bottom 106 SSMF Guide TOOLS REQUIRED
More informationAmtryke Model AM-12 & AM-16
Amtryke Model AM-12 & AM-16 Carton Contents Carefully remove and lay out all parts from the carton so as not to scratch or lose any parts or pieces. The shipping carton should contain the pictured items
More informationInstallation Instructions Dodge Ram P/N D80014
Patent # US 7,100,956 BA Installation Instructions Dodge Ram 94-01 P/N D80014 CAUTION IT IS NOT RECOMMENDED MOUNTING THE TIREGATE ON TRUCKS THAT HAVE REAR FIBER GLASS REPLACEMENT FENDERS. THE BED DOES
More informationPrime Engineering GRANSTAND II
OWNER S MANUAL PRODUCT PHOTO PARTS LIST ASSEMBLY INSTRUCTIONS FITTING & ADJUSTING DAILY USAGE ACCESSORIES MAINTENANCE WARRANTY Prime Engineering GRANSTAND II Manufactured By Prime Engineering A Division
More informationZippie GS. Growth System
Zippie GS Growth System Folds compactly for easy transport Growth system adjusts in width and depth to last kids a long, long time. Versatile design meets most functional needs. Crash Tested for safe bus
More informationSeats ! WARNING: SEAT ADJUSTMENT. Seat fore and aft position and, if specified, cushion height and front tilt (B):
Seats SEAT ADJUSTMENT Do not make adjustments when the vehicle is moving. Front passengers must not ride with the seat fully reclined. Front seat adjustment The front seats are adjusted electrically by
More informationPositioning & Support USER MANUAL. Combo Series. Stealth s User Manual and Maintenance Guide for the Combo Series Headrest
Positioning & Support USER MANUAL Combo Series Stealth s User Manual and Maintenance Guide for the Combo Series Headrest Customer Satisfaction 1.0 Stealth Products strives for 100% customer satisfaction.
More informationAdvancement Chair. R901, R902, & R903 Product Manual
Advancement Chair R901, R902, & R903 Product Manual Contents Warnings and Important Information 3 Recommended Use 4 User and Item Dimensions 4 Assembly and Adjustment Information 5 Maintenance 14 Cleaning
More informationSEATING INSTRUCTIONS. Trooper
Trooper Trooper Asynchronous Control 6 8 2 Seat Depth 9 Arm Width 5 Tilt Tension 7 Back Angle Forward Tilt 1 Seat Angle 1. Enables the seat to adjust to the preferred height. To raise the seat, lift your
More informationBasic Task (B) Chair Adjustment Information
Basic Task (B) Adjustable back depth For custom lumbar support. To adjust, turn handwheel left to loosen. Move the back in or out to the desired depth, then turn handwheel to the right to tighten. Swivel
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA / SEQUOIA PART # &
(W) INSTALLATION INSTRUCTIONS PART # 501894 & 501895 PARTS LIST: 1 Grille Guard 4 3/8" Flat Washers 1 Driver/Left Frame 2 3/8" Nylon Lock Nuts 1 Passenger/Right Frame 4 12mm Plastic Washers 1 Driver/Left
More informationM1 - NPO. Dealer Information. Client Information. Client Measurements
Dealer Information * Contact: Dealer Code: * Dealer Name: Address: * City: * Province: * Phone#: * Fax#: PO#: Email Address: Client Information Permobil recommends that the client is evaluated by a certified
More information5 details (same width)
Dexter + Dexter Plus TM 5 details (same width) TM Dexter TM Intensive use and multi-shift seating is comfortable, generous and well designed. 2437-1 Medium Back Synchro-Tilter This state-of-the-art multi-shift,
More informationINSTALLATION INSTRUCTIONS BULL BAR DODGE RAM 1500 PART # B-D1091;B-D2091
INSTALLATION INSTRUCTIONS PART # B-D1091;B-D2091 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Brackets (for trucks without tow hooks only) 8 12-1.75mm Hex Nuts
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY TRUTRACK TRUNNION BAR WEIGHT DISTRIBUTION SYSTEM MAINTENANCE Keep the socket-mounted ends of the
More informationFUZE T20. Order Form - Canada Prices in Canadian Dollars. January 1, C u s t o m e r a n d O r d e r I n f o r m a t i o n.
C u s t o m e r a n d O r d e r I n f o r m a t i o n Purchase Order * Dealer/Provider Name * Purchaser Name and Contact Information * Billing Address * Tag v.070118 Shipping Address * * required F r a
More informationPhoto is courtesy of Enable-Me COMFORT SUPERIOR SEATING ACCESS ADJUSTABILITY. REHAB SHOWER COMMODE CHAIRS The Choice of Health Care Professionals
Photo is courtesy of Enable-Me COMFORT SUPERIOR SEATING ACCESS ADJUSTABILITY REHAB SHOWER COMMODE CHAIRS The Choice of Health Care Professionals INTRODUCING THE NEW LOW COST JAZ AP & SP The JAZ AP and
More informationINSTALLATION INSTRUCTION BULL BAR DODGE RAM 1500 PART NUMBER
INSTALLATION INSTRUCTION 09-12 DODGE RAM 1500 PART NUMBER - 200691 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Mounting Brackets (for trucks without tow hooks
More informationAssembly Guide T9200, T9300, T9400HRT, T9500HRT, T9600HRT, T9700HRT, & T9700S PLATFORM TREADMILLS
Assembly Guide T9200, T9300, T9400HRT, T9500HRT, T9600HRT, T9700HRT, & T9700S PLATFORM TREADMILLS T9200 T9300 T9400HRT T9500HRT T9600HRT T9700HRT platform treadmills T9700S To avoid possible damage to
More informationPremium Dry Freight (Plywood) Door Installation REFERENCE FIGURE 1
Premium Dry Freight (Plywood) Door Installation A Premium door can be identified as usually having a two-spring balancer, 2 diameter (nominal) rollers, and end hinges with removable covers. If your Whiting
More informationMAINTENANCE WEIGHT RATINGS WARNINGS. warning: never exceed your vehicle manufacturer's recommended towing capacity
Installation instructions warning: never exceed your vehicle manufacturer's recommended towing capacity Round Bar WEIGHT DISTRIBUTION kit MAINTENANCE Keep the socket-mounted ends of the spring bars and
More information(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers
PARTS LIST: EXTREME GRILLE GUARD 1 Extreme Heavy Duty Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting Bracket 4 10mm x 24mm OD x 2.2mm Flat Washers
More informationPassenger/Right. Driver/Left. Driver/Left Side Frame. Mounting Bracket. (2) 12mm Double Nut Plates (models without tow hooks)
PARTS LIST: Qty Description Qty Description 1 Grille Guard 4 10-1.5mm x 30mm Hex Bolt 1 Driver/left Frame Bracket 8 10mm x 24mm OD x 2.2mm Flat Washer 1 Passenger/right Frame Bracket 4 10-1.5mm Nylon Lock
More informationAERO-TRI BAR FELT CARBON FIBER AEROBAR INSTRUCTION MANUAL
AERO-TRI BAR FELT CARBON FIBER AEROBAR INSTRUCTION MANUAL TABLE OF CONTENTS Introduction.......................................................... 3 Parts list..........................................................
More informationOlli and Ozzi Instruction Manual
0 000011 6 Olli and Ozzi Instruction Manual This belt-positioning booster seat (booster seat) is designed for use by children who meet these requirements: 40 57 in. 101 145 cm. 40 120 lb. 18 54 kg. 4 years
More informationSequoia 2 Post System
Sequoia 2 Post System Owner s Manual Use and Care Fault Finding Warranty Information Table of Contents Sequoia 2 Post System Introduction... 3 Overview... 3 Placement of the Sequoia... 4 Components of
More informationMAINTENANCE WEIGHT RATINGS WARNINGS. warning: never exceed your vehicle manufacturer's recommended towing capacity
Installation instructions warning: never exceed your vehicle manufacturer's recommended towing capacity Round Bar WEIGHT DISTRIBUTION MAINTENANCE Keep the socket-mounted ends of the spring bars and the
More informationTrike. Instructions. Model Number: 72633
Trike Model Number: 72633 Instructions Please keep these instructions for future reference. Adult assembly is required. Tools needed for assembly: Hammer, Phillips Screwdriver, Scrap Block of Wood. (Tools
More informationPart List ASSEMBLY INSTRUCTIONS. Backrest. Seat. Armrests. Star Base. Caster. Arm Bolts (M8 X 22mm) Back Bolts (M8 X 15mm) Allen Wrench
IOO-BLK/IOO-WHT ASSEMBLY INSTRUCTIONS IOO-BLK/IOO-WHT Part List Key Description Part Qty. Spare A Backrest B Seat C Armrests ( left & right armrest) 2 D Seat Post(Cylinder) E Star Base F Caster r 5 G H
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY PIN-STYLE TRUNNION BAR WEIGHT DISTRIBUTION KIT MAINTENANCE Keep the socket-mounted ends of the spring
More informationIcon Back System with VariLock Hardware
Icon Back System with VariLock Hardware Simple Streamlined Secure Overview Available in 4 models: Low Mid Tall Deep Design Features: Simple yet secure hardw are Integrated permanent mount Aluminum shell
More informationTEL:1-866-XANATOS. INSTALLATION INSTRUCTIONS PART#: SR-DOR SPARTAN RUNNING BOARD DODGE PROMASTER 136 /159 wheel base 14-UP
TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: SR-DOR303285 SPARTAN RUNNING BOARD DODGE PROMASTER 136 /159 wheel base 14-UP PARTS LIST: 1 Driver/left Spartan Running Board 12 8-1.25mm x 25mm Hex Bolts
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationINTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D
INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D330-0021 APPLICATION: 2014-16 F22 228i & xdrive coupe (see restrictions below) 2015-16 F23 228i & xdrive convertible 2012-16 F30 328i & xdrive
More informationTHE GLIDER 5th Wheel Attachment
April 2007 APPLICATION: INSTALLATION INSTRUCTIONS MODEL NO. 70460 70046 THE GLIDER 5th Wheel Attachment For use on short bed pickup applications US Patent No. 6247720 COMPLETE PARTS LIST Part Description
More informationDODGE RAM 1500 / 2500 / 3500
Installation Instructions: DR5 DODGE RAM 1500 / 2500 / 3500 8 BED LENGTH 1500: (2009-2017) 2500 & 3500: (2010-2017) TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips
More informationOPERATION WARNING WARNING
OPERATION WARNING WARNING SERIOUS INJURY MAY OCCUR IF HEAD CLEARANCE IS NOT ADEQUATE. BEFORE DRIVING OR RIDING IN VEHICLE, ENSURE THAT THERE IS ADEQUATE HEAD CLEARANCE AT THE MAXIMUM UPWARD TRAVEL OF SEAT.
More informationInstallation instructions
Installation instructions warning: never exceed your vehicle manufacturer's recommended towing capacity BOLT-TOGETHER WEIGHT DISTRIBUTION MAINTENANCE Keep the socket-mounted ends of the spring bars and
More informationPARTS LIST: VIEWPOINT RUNNING BOARD NISSAN MURANO EXCLUDES 2dr CROSSCABRIOLET CONVERTIBLE
PARTS LIST: VIEWPOINT RUNNING BOARD Qty Description Qty Description 1 Driver/Left Running Board 14 10-1.5mm x 35mm Bolt Plates 1 Passenger/Right Running Board 6 10-1.50mm x 30mm Hex Bolt 1 Driver/Left
More informationInstallation Instructions
DODGE 20K Industry Standard Rail Custom Mounting Kit #2740 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationThe economical 42U cabinet that s easy to transport and assemble on-site.
RMT3200A-R2 Universal Flat Pack Cabinet The economical 42U cabinet that s easy to transport and assemble on-site. Customer Support Information Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
More informationASSEMBLY AND USER GUIDE
ASSEMBLY AND USER GUIDE "DESIGNED FOR THE OPTIMAL GAMING EXPERIENCE AND UNPARALLELED COMFORT" Congratulations on purchasing your EDGE GX1 gaming chair. The chair has several important adjustments. Spending
More informationProtect your short bed pickup by using a positioning device like the Husky Glider with your 16K S
Husky Tilt Plate 16K S Straight Jaw Fifth Wheel Hitch (Husky Silver Series) Husky 16K S Tilt Plate Design Advantages: Addition of a pop out safety hookup indicator Engineered/designed tolerances for less
More information(W) INSTALLATION INSTRUCTIONS 90DEG BENT END SIDEBARS F-150 SUPER CREW CAB PART #DZ /DZ /DZ
(W) INSTALLATION INSTRUCTIONS PART #DZ 371691/DZ 371692/DZ 371693 PARTS LIST: Qty Description Qty Description 1 Driver/Left Sidebar 2 12mm x 45mm Double Bolt Plates 1 Sidebar 4 s 1 Driver/Left Mounting
More informationINTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D
INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D330-0021 APPLICATION: 2014-16 F22 228i & xdrive coupe (see restrictions below) 2012-16 F30 328i & xdrive sedan 2014-16 F31 328i xdrive wagon 2014-16
More informationPrime Engineering Superstand
OWNER S MANUAL PRODUCT PHOTO PARTS LIST ASSEMBLY INSTRUCTIONS FITTING & ADJUSTING DAILY USAGE ACCESSORIES MAINTENANCE WARRANTY Prime Engineering Manufactured By Prime Engineering A Division of Axiom Industries
More informationSUT-250-S (These instructions are used for SUT-250-SCLC also)
SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16,
More informationSPRING MAX. TONGUE MAX. GROSS TRAILER BAR WEIGHT(LB) WEIGHT (LB)
INSTALLATION / OPERATION INSTRUCTIONS WEIGHT DISTRIBUTING HITCH SYSTEMS 7901, 7902, 7903, 7979 (DUAL SWAY CONTROL ATTACHMENT) 7901=600LB WDH KIT, 7902=800LB WDH KIT, 7903=1200LB WDH KIT, 7979=HEAD KIT
More informationLOCKN LOAD MOUNTING KIT
LOCKN LOAD MOUNTING KIT TM VOLKSWAGEN AMAROK 2 BAR FIXED POINT HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES + CARGO FIRST TIME INSTALLATION
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # 2067/2067-2
INSTALLATION INSTRUCTIONS 07-15 TOYOTA TUNDRA 08-15 TOYOTA SEQUOIA PART # 2067/2067-2 PARTS LIST: 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting
More informationSTOP IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED TO ACTIVATE YOUR LIMITED LIFETIME WARRANTY GO TO: CORSAPERFORMANCE.
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust We ask that you take a few moments to complete
More informationRating when used as a weight distributing hitch with spring bars:
May 2004 APPLICATION: INSTALLATION INSTRUCTIONS MODEL NO. 70201 Bolt Together Weight Distributing Hitch System Without Shank Rating when used as a weight distributing hitch with spring bars: Part Number
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD F-150 P/N 3066;3066-2
INSTALLATION INSTRUCTIONS P/N 3066;3066-2 PARTS LIST: 1 Grille Guard 4 12mm Lock Washer 1 Driver/left Frame Bracket 4 10-1.5mm x 30mm Hex Bolt 1 Passenger/right Frame Bracket 8 10mm x 24mm OD x 2.2mm Flat
More informationMirage Dental Delivery Unit MSP3500/3550 Installation Instructions
! Mirage Dental Delivery Unit MSP3500/3550 Installation Instructions TPC 851 S. Lawson St. City Of Industry, CA 91748 P626-810-4337 Fax 626-810-4245 REV. 1-1-13 Table on Contents: Page GENERAL INFORMATION
More information