Titan Articulating Arm Dual Media Cart INSTALLATION INSTRUCTIONS. Page 1
|
|
- Darleen Smith
- 6 years ago
- Views:
Transcription
1 Titan Articulating Arm Dual Media Cart INSTALLATION INSTRUCTIONS Page 1
2 INSTRUCTIONS CLEARONE DOCUMENT (REVISION 2.0) February TITAN DUAL ARTICULATING ARM MEDIA CART The Titan Dual Articulating Arm Media Cart is assembled from the shipped parts using standard tools. PARTS USED IN ASSEMBLY A B C D 8X 8X 16X 2X E 2X F 4X G 5X H I J M4 M5 M6 M8 M8 M4 or M5 M6 or M8 4 each (per TV) [8 each] 4 each (per TV) [8 each] K L M 4 (per TV) [8] 5 (per TV) [10] 4 (per TV) [8] 1 Used to secure camera to shelf Not shown in any assembly images M4 M5 M6 4 each (per TV) [8 each] M8 Page 2
3 MEDIA CART COMPONENTS USED IN ASSEMBLY Short Plate 4X Long Plate 4X Spacer Bracket Lock Plate 2X Left Side Assembly Right Side Assembly Camera Mounting Bracket Adjustable Channel Tilt Camera Shelf TV Bracket 2 (per TV) [4] Reinforcing Plate 1 (per TV) [2] TV Inner Bracket 4 (per TV) [8] TV Mounting Tray 1 (per TV) [2] Page 3
4 INSTRUCTIONS FOR ASSEMBLING THE ARTICULATING ARMS AND TV S ON THE MEDIA CART Step 1 1. Place the Right Side Assembly on the top of the cart. Note that the directional arrows at the base of the assembly are to indicate the right or left assembly and point to the outside of the cart when positioned. 2. Align the holes of the assembly to the corresponding holes on the top of the cart. Right Side Assembly A B C Short Plates C Long Plates Page 4
5 Step 2 1. Bolt the Right Side Assembly on the top of the cabinet using 4 bolts (A), 4 washers (B), 2 Short Plates and 2 Long plates with the 4 spacers (C) provided to fill the gap between the long and short plates. Be sure to put Long plates and spacers (C) outside and inside the cabinet. The Long Plates are threaded to accept the bolts. Do not overtighten the bolts. C Short Plates A Long Plate Step 3 1. Repeat the procedure for the Left Side Assembly. Page 5
6 Step 4 1. Assemble the Camera Mounting kit by attaching the Camera Mounting Bracket to the Spacer Bracket with 4 bolts (F) and lock nuts (G). 2. Attach the Adjustable Channel to the Camera Mounting Bracket. The Adjustable Channel has an embedded bolt that can be fastened with a nut (G) on the opposite side. 3. Attach the Tilt Camera Shelf to the Adjustable Channel using the bolt (I), spacer (J) and nut (H). Tilt Camera Shelf H J Adjustable Channel I Camera Mounting Bracket G Step 5 F Spacer Bracket 1. Remove the Clamping Lever from the top of each Articulating Arm assembly. 2. Place the Spacer Bracket with the Adjustable Channel and Tilt Camera Shelf onto the threaded inserts and adjust Articulating arms as needed. 3. Bolt it together using the Clamping Levers and provided flat washers. 4. Make sure the Articulating Arms are securely tightened to the cabinet. Page 6
7 Step 6 1. Assemble the mounting for each TV display. Place the TV s face down on a safe, non-scratch solid surface. Use the TV Brackets, Inner Brackets, Spacers, M4, M5, M6 or M8 screws, lock washers and washers suitable to the mounting holes of the TV. Position the TV Inner Brackets inside the TV Brackets, adjust to the proper spacing for your mounting holes, then place screws, washers and optional spacers so that the assemblies are firmly in place. Do not overtighten the screws or use power tools for assembly. K Optional Spacers TV Inner Bracket Reinforcing Plate TV Bracket 2 (per TV) [4] TV Mounting Tray L M 2. Mount the Reinforcing Plate on the TV Tray, then the TV Tray with Reinforcing Plate to the TV Brackets. Slots in the TV brackets and TV mounting tray may be used to adjust the vertical and horizontal position of the TV s, respectively. Depending on the size of the TV s, this might be necessary to clear the top of the cart or to adjust the gap between the units. Do not overtighten the screws or use power tools for assembly. Page 7
8 Step 7 1. Fully extend the arms to a position that allows for easy installation of the TVs. Lift the TV (with the attached mounting hardware from step 6) onto the Articulating Arm. Make sure the Reinforcing Plate fits snug against the Articulating Arm assembly with the weight supported by the TV Support Cleat on the articulating arm. TV Support Cleat NOTE: This operation requires the assistance of another person to lift and hold the TV into place as the attachments are made. 2. Secure the TV to the Articulating Arm with the screw (L) placed through the hole near the bottom of the TV Support Cleat. Then place the lock plate, spacer (D), and the lock knob (E) over the bolt at the top of the cleat on the articulating Arm, then tighten. Note that there is a small amount of left-right tilt that can be brought level and set with the locking knob. Lock Plate D E 3. Repeat this procedure for the remaining TV and Articulating Arm. L Page 8
9 Step 8 1. Power and equipment cables for the TV s can be dressed through the Cable Access Holes in the Cabinet top, up through the Spacer Bracket and over to the TV Mounting Plate to conceal them and make rotation of the Articulating Arms free from obstruction. Rear View of Completed Assembly (TV s not Shown) TV Cable Access Holes CLEARONE LOCATIONS HEADQUARTERS: Salt Lake City, UT USA 5225 Wiley Post Way Suite 500 Salt Lake City, UT Tel: Toll Free: Fax: sales@clearone.com EMEA Tel: 44 (0) global@clearone.com APAC Tel: global@clearone.com LATAM Tel: global@clearone.com TechSales Tel: techsales@clearone.com Technical Support Tel: tech.support@clearone.com Rev ClearOne, Inc. All rights reserved. Information in this document is subject to change without notice. Page 9
TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: SR-FOR SPARTAN RUNNING BOARD FORD ECONOLINE 99-14
TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: SR-FOR203796 SPARTAN RUNNING BOARD FORD ECONOLINE 99-14 PARTS LIST: 1 Driver/Left Side Spartan Running Board 2 10mm Lock Washers 1 Passenger/Right Side
More informationLateral Hip Support INSTALLATION & SET-UP MANUAL. (with Fixed or Removable Hardware) Lateral Hip Support- Fixed Assembly
Lateral Hip Support (with Fixed or Removable Hardware) Lateral Hip Support- Fixed Assembly Lateral Hip Support- Removable Assembly (Note: assemblies diagrams are shown for left side only) INSTALLATION
More informationOne- Touch Installation Instructions
One- Touch Installation Instructions 1 1 Height Adjustable Pivot w/ screws 9 Upper Work Surface 2 Rail Mount Knobs 10 Back Cover 3 Transformer 11 Center Pivot w/ screws 4 Support Legs 12 Left Monitor Arm
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500 QUAD CAB
INSTALLATION INSTRUCTIONS PARTS LIST: 2 Steel Running Boards 5 12mm Lock Washers 1 Driver/Left Mounting Bracket 5 12mm Hex Nuts 1 Driver/Left Center Mounting Bracket 6 10-1.5mm x 35mm Hex Bolts 2 Driver/Left
More informationInstallation Guide. Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) Section 1.0: Mounting the M-Series Arm Parts Reference...
Installation Guide Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) The purpose of this guide is to describe installation of the MP90 M-Series Wall Mount Kit. Table of Contents Section 1.0: Mounting
More informationMyriad Keyboard and Mouse Tray, Articulating Arm Installation Instructions
670 Zinser Street Schofield, WI 54476 Version Dated: 4/2/15 Myriad Keyboard and Mouse Tray, Articulating Arm Installation Instructions Read all the instructions before beginning. Hardware Pack # 50525
More information415/417NR NOTEBOOK TRAY ASSEMBLY & OPERATION INSTRUCTIONS
6703 Zinser Street Schofield, WI 4476 Version Dated: 2/27/1 41/417NR NOTEBOOK TRAY ASSEMBLY & OPERATION INSTRUCTIONS Read all the instructions before beginning. Hardware Pack # 2372 & 031 (Track Hardware)
More informationTOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.
TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm Socket Hack Saw
More informationLicense Plate Bracket (4) Rubber Plugs. (2) Retaining Rings (2) Foam Spacers
LDB-NTIT62-FB PARTS LIST: 1 LD1 Bumper Assembly 2 8mm Hex Nuts 1 Driver/left L Bracket (center LED light) 2 6mm x 20mm Button Head Bolts 1 Passenger/right L Bracket (center LED light) 4 6mm x 18mm x 1.6mm
More information6 6mm Nylon Lock Nuts 4 12mm Lock Washers 12 6mm Hex Nuts 4 12mm x 32mm x 3mm Flat Washers. (2) 12mm x 40mm Narrow Bolt Plates (Rear)
PARTS LIST: ALUMINUM VIEWPOINT RUNNING BOARDS 1 Driver/Left Running Board 4 12mm Hex Nuts 1 Passenger/Right Running Board 2 10mm Lock Washers 1 Driver/Left Mounting Bracket 2 10mm x 30mm x 2.5mm Flat Washers
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY FRONT BUMPER 2015 FORD F150
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Heavy Duty Bumper Assembly 14 12-1.75mm x 45mm Hex Bolts 1 Driver/Left Frame Mounting Bracket 28 12mm x 37mm x 3mm Flat Washers 1 Passenger/Right Frame Mounting
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500 REGULAR CAB REGULAR CAB
INSTALLATION INSTRUCTIONS PARTS LIST: 2 Steel Running Boards 3 12mm Hex Nuts 1 Driver/Left Mounting Bracket 4 10-1.5mm x 35mm Hex Bolts 1 Driver/Left Support Bracket 4 10mm x 27mm OD x 3mm Flat Washers
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500/ CREW CAB
INSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS PARTS LIST: 1 Driver/Left Steel Running Boards 5 12mm Lock Washers 1 Passenger/Right Steel Running Boards 5 12mm Hex Nuts 1 Driver/Left Mounting Bracket
More informationINSTALLATION GUIDE WSD47UINT13 WEAPON STORAGE DRAWER & ASBD47UINT13 ALUMINUM STORAGE DRAWER CURRENT FORD UTILITY INTERCEPTOR
INSTALLATION GUIDE WSD7UINT WEAPON STORAGE DRAWER & ASBD7UINT ALUMINUM STORAGE DRAWER 0 - CURRENT FORD UTILITY INTERCEPTOR STRONG RELIABLE SECURE 800.80.80 THESE COMPONENTS ARE REQUIRED TO INSTALL THE
More informationTilt Steering Column Instruction Sheet
Tilt Steering Column Instruction Sheet PLEASE READ BEFORE YOU BEGIN TO INSTALL COLUMN Flaming River all new parts pledge. The best in the business and a three-year warranty. Flaming River tilt steering
More informationReplacing the Column Stabilizer Tube with Finger-tight Fittings
715000926, REV. H 1 OF 9 Replacing the Column Stabilizer Tube with Finger-tight Fittings This document explains how to replace the column stabilizer tube assembly with finger-tight fittings in the ACQUITY
More informationInstallation Guide Philips MP90 VHM Wall Mount Kit
Installation Guide Philips MP90 VHM Wall Mount Kit The purpose of this guide is to describe the procedures for installing the MP90 VHM Wall Mount Kit. Table of Contents Section 1.0: Mounting the VHM-Series
More informationSOLUTION STATION Instruction Manual
SOLUTION STATION Instruction Manual WAXIE Sanitary Supply 9353 WAXIE Way San Diego, CA 92123 Phone: 800.995.4466 www.waxie.com TABLE OF CONTENTS Unpacking Instructions Disclaimer..... Warranty... Introduction...
More informationIntegra Manually Operated Distribution Valves
P/N 01-025695 REV. D 08/17 INSTRUCTION SHEET Integra Manually Operated Distribution Valves 1", 2-way, multi-turn and sampling manual designs; 1 1 4" 2-way, multi-turn manual designs REPAIR INSTRUCTIONS
More informationEDUIMS INTERACTIVE MEDIA STATION. Assembly Instructions Qty 1 Bottom Frame Assembly Qty 1 Bottom Support Panel LH
EDUIMS INTERACTIVE MEDIA STATION 022-3188 - Qty 1 Bottom Frame Assembly 010-7266 - Qty 1 Bottom Support Panel RH 010-7265 - Qty 1 Bottom Support Panel LH 022-3187 - Qty 1 Upper Frame Assembly 022-3655
More informationCommercial Pro Plow Combo, 50" ATV
CHANGING YOUR LANDSCAPE SINCE 1945 swisherinc.com OWNER S MANUAL 19975 Starting Serial #: L215-001001 Commercial Pro Plow Combo, 50" ATV IMPORTANT Read and follow all Safety Precautions and Instructions
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More information8mm Bolt Plate. (15) 8mm U-Clip Nuts. Passenger/right front Upper Bracket
PARTS LIST: 2 T-6 Side Bars 8 8mm Double Bolt Plates 1 Passenger/right Upper Bracket (all incl. DEF) 17 8-1.25mm x 25mm Hex Bolts 1 Passenger/right Lower Bracket (all incl. DEF) 33 8mm x 24mm x 2mm Flat
More informationTB-690 Conveyor/Stacker
TB-690 Conveyor/Stacker ASSEMBLY AND OPERATIONS MANUAL Revised: 1-9-09 RENA SYSTEMS INC. 136 Green Tree Road STE 140 Oaks, PA 19456-1069 Phone: (610) 650-9170 Fax: (610) 650-9171 E-Mail: support@renausa.com
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationI - Sheet Number I-PW Rev. A
I - Sheet Number I-PW013988 Rev. A Installation Instructions Part # 23948007/24048007 PARTS LIST: 1 Driver/left Sidebar 17 8-1.25mm x 25mm Hex Bolts 1 Passenger/right Sidebar 17 8mm x 24mm x 2mm Flat Washers
More information(2) 10mm x 50mm T-Bolts (For Rear Brackets only) (6) 10mm Rod Bolts. (2) 10mm x 35mm Button Head Bolt Plates
PARTS LIST: 1 Driver/Left side Running Board 2 10mm x 50mm T Bolts 1 Passenger/Right side Running Board 6 10mm Bent Threaded Rod Bolts 1 Driver/Left front Mounting Bracket 8 10mm Plastic Retainers 1 Passenger/Right
More information(2) Top Support Backing Plates. Passenger/Right Top Bracket. (2) Frame Mounting Brackets. (2) 12mm x 35mm Single Bolt Plates
PARTS LIST: 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting Bracket 8 10mm x 27mm OD x 3mm Flat Washers 1 Passenger/Right Mounting Bracket
More informationINSTALLATION INSTRUCTIONS PART#: SR-GMR13796 SPARTAN RUNNING BOARD CHEVY EXPRESS 1500/2500/3500 GMC SAVANNA 1500/2500/ UP
INSTALLATION INSTRUCTIONS PART#: SR-GMR13796 SPARTAN RUNNING BOARD CHEVY EXPRESS 1500/2500/3500 GMC SAVANNA 1500/2500/3500 03-UP PARTS LIST: 1 Driver Side- 37 Spartan Running Board 8 12mm Hex Nuts 1 Passenger
More informationAssembly Guide ELECTRIC. Model Numbers: C1. (English) /14/11
Assembly Guide Model Numbers: 12601559 12601578 12601663 12601664 12601665 12601688 12601514 12601514-C1 ELECTRIC (English) 42804641 09/14/11 2 ASSEMBLY GUIDE A, B, C, Assembly: CAUTION: For your safety,
More informationIrunning Board Installation Instruction
PARTS LIST: Item QTY Description Item QTY Description #1 2 Running Board(use for left or right) #8 13 8-1.25mm x 25mm Hex Bolt #2 1 Passenger/right Upper Bracket #9 13 8mm x 24mm x 2mm Flat Washer #3 1
More information(2) 10mm x 50mm T-Bolts (For Rear Brackets only) (6) 10mm Rod Bolts. (2) 10mm x 35mm Button Head Bolt Plates
PARTS LIST: 1 Driver/Left side Running Board 2 10mm x 50mm T Bolts 1 Passenger/Right side Running Board 6 10mm Bent Threaded Rod Bolts 1 Driver/Left front Mounting Bracket 8 10mm Plastic Retainers 1 Passenger/Right
More information11-16 Jeep Grand Cherokee 4 Oval Sidebars
Page 1/6 Part #11594.04 Passenger/Right Rear Inner Support Bracket (4) 12mm x 40mm Bolt Plates Driver/Left Rear Inner Support Bracket (2) 10mm x 35mm Long Bolt Plates (2) 10mm x 35mm Short Bolt Plates
More informationHARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX
HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX Read and follow these special instructions along with the standard instructions carefully before installing or using
More informationQ15P. Mitsubishi MQ Triton Dual Cab
Mitsubishi MQ Triton Dual Cab Page 1 of 12 Fitting Instructions Part Number Mitsubishi MQ Triton Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationFOR WALL MOUNT COMBINATION ARMS
INSTALLATION MANUAL FOR WALL MOUNT COMBINATION ARMS LIGHT DUTY ARMS HEAVY DUTY ARMS KEYBOARD TRAY VERSION Weight Capacity 4-20 lbs KEYBOARD TRAY VERSION Weight Capacity 8-40 lbs WORKSTATION VERSION Weight
More informationSUPERMOTOR-V3 INSTALLATION VERSION
SUPERMOTOR-V3 INSTALLATION VERSION 09.03.14 IMPORTANT NOTE: Before starting the installation go to Utilities->Preferences and set the engagement strength for both motors to 3. 1. Remove their clear plastic
More informationpanelclaw.com Polar Bear III for 10 Degree
panelclaw.com Polar Bear III for 10 Degree Installation Manual Document Number 9910024 Rev A March 2014 Revision History Rev ECO # Date Description of Changes Approved By 01 TBD 02-FEB-14 Initial Draft
More informationLeft and Right Bar Light L Brackets. Driver/Left Frame Bracket
PARTS LIST: 1 Bumper 14 12mm Nylon Lock Nuts 1 Bull Nose Hoop 2 10mm Double Bolt Plates 1 Winch Tray 4 10-1.5mm x 25mm Hex Bolts 1 Driver/left Frame Mounting Bracket 8 10mm x 30mm x 2.5mm Flat Washers
More informationPARTS LIST: VIEWPOINT RUNNING BOARD NISSAN MURANO EXCLUDES 2dr CROSSCABRIOLET CONVERTIBLE
PARTS LIST: VIEWPOINT RUNNING BOARD Qty Description Qty Description 1 Driver/Left Running Board 14 10-1.5mm x 35mm Bolt Plates 1 Passenger/Right Running Board 6 10-1.50mm x 30mm Hex Bolt 1 Driver/Left
More informationPassenger/Right Support Bracket Driver/Left Support Bracket
PARTS LIST: 1 bumper 24 12mm x 37mm OD x 3mm Flat Washers 1 Driver/left Mounting Bracket 14 12mm Lock Washers 1 Passenger/right Mounting Bracket 14 12mm Hex Nuts 1 Driver/left Lower Support Bracket 2 Plastic
More informationPassenger/Right Top Support Bracket. (2) 10mm Nut Plates
PARTS LIST: 1 Extreme Grille Guard 16 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 10 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 10 12mm Hex Nuts 1 Driver/Left
More information4" Oval Nerf Bar. Part No. A1535S/B. PARTS LIST: Qty Part Description Qty Part Description
` 4" Oval Nerf Bar Part No. A1535S/B Fits: 2009-2015 Dodge Ram 1500 Reg Cab 2010-2015 Dodge Ram 2500/3500/4500/5500 Reg.Cab REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not
More informationMatrx Back Interface for the
Matrx Back Interface for the Quantum Tru-Balance 3 Seating System Installation Instructions TRD0357, Rev A Important Symbols in this Manual Setting up and operating your wheelchair safely depends on your
More informationSWM Series Wall Mount
I N S T A L L A T I O N SWM Series Wall Mount C293M-E (9/13) Contents Important Safety Instructions............................................................................................ 3 Description...........................................................................................................
More informationIntegra Pneumatically Operated Valves
P/N 0-025696 REV. D 09/7 INSTRUCTION SHEET Integra Pneumatically Operated Valves ", 2-way, normally open, normally closed, sampling pneumatic designs; 4" 2-way, normally open, normally closed designs REPAIR
More informationRunning Board. Part No. RBV05B. PARTS LIST: Qty Part Description Qty Part Description
` Running Board Part No. RBV05B Fits: 2014 - Current Dodge Ram Promaster 136 /159 wheel base REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting May be Required Drilling Required
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Haul-Your-Might T3 Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm
More informationFront HD Bumper. Part No. FHDB003TI. PARTS LIST: Qty Part Description Qty Part Description
` HD Bumper Part No. FHDB003TI Fits: 2015-2016 Chevrolet Silverado 2500/3500 ASSISTANCE IS RECOMMENDED. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required Drilling
More informationassembly guide ELECTRIC Model Numbers: Estimated time required for assembly: 1 Hour (English) /02/10
assembly guide Model Numbers: 11601514 11601559 11601578 Estimated time required for assembly: 1 Hour ELECTRIC (English) 42804382 6/02/10 2 ASSEMBLY GUIDE A, B, C, Assembly: CAUTION: For your safety, before
More informationINSTALLATION MANUAL. Level of Difficulty. Parts List. Product Image. Tools Required. Notes and Maintenance. Torque Specifications.
INSTALLATION MANUAL Parts List 1 Bull bar 2 Upper frame mounting bracket 1 Driver / left lower frame mounting bracket 1 Passenger / right lower frame mounting bracket 2 Button head bolt, 6mm 4 Flat washer,
More informationThis procedure is best performed on a vehicle lift, however it is possible to install these coilovers using a floor jack and jack stands.
Description: FeatherLight Single Adjustable Corvette Coilovers Part Number: 430-401004-N Application: 2014-2015 Chevrolet Corvette (C7) Note: Some models might be equipped with Magnetic Ride electric adjustable
More information8mm Bolt Plate. Passenger/right front only Upper Mounting Bracket
4 SIDE STEPS PARTS LIST: 1 Driver/left Side Step 13 8-1.25mm x 25mm Hex Bolts 1 Passenger/right Side Step 13 8mm x 24mm x 2mm Flat Washers 1 Passenger/right Upper Bracket (all incl. DEF) 13 8mm Lock Washers
More informationINSTALLATION INSTRUCTIONS
TEL1-866-XANATOS INSTALLATION INSTRUCTIONS SIDE BAR PART#: 9B076701SS\9B076701A PARTS LIST: 1 Driver/Left Sidebar 4 1/2" x 1-1/2" x 1/8" Flat Washers 1 Passenger/Right Sidebar 4 1/2" Lock Washers 2 Front
More information(6) Universal Mounting Brackets (NOTE: same bracket used for left or right side installation) Driver/left Running Board (example only)
PARTS LIST: Qty Description Qty Description 6 Universal Left/Right Mounting Brackets 12 6-1.0mm x 20mm T-Bolts 12 8-1.25mm Clip-On Nuts 12 6mm x 22mm OD x 2mm Flat Washers 12 8-1.25mm x 25mm Hex Bolt 12
More informationMobile TV Mount Stand with Hydraulic Height Adjustment Model: DMS-172
Mobile TV Mount Stand with Hydraulic Height Adjustment Model: DMS-172 Instruction Manual Images may be different from actual product Disclaimer It is Dyconn s intention to have all the correct information
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY FRONT BUMPER CHEVY SILVERADO 1500
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Heavy Duty Bumper Assembly 16 12mm Nylon Lock Nuts 1 Driver Mounting Bracket 8 4mm x 10mm Socket Head Screws 1 Passenger Mounting Bracket 4 Sensor Plugs 4 Support
More informationCondor Manual. Corporation
Condor Manual Corporation PREFACE IMPORTANT, PLEASE READ CAREFULLY Thank you for your purchase with Amico Accessories Inc. This unit is designed for long lasting performance, providing the end user complies
More informationAP-Xtreme Sim-Racing Chassis Master Assembly Guide
AP-Xtreme Sim-Racing Chassis Master Assembly Guide This guide covers all options available for the AP-Xtreme chassis. Some sections of this guide will be skipped based on the options chosen. APX1000 APX2000
More informationDescription: These racing sway bars are engineered to be a lightweight, adjustable racing sway bar system for C5 and C6 Corvettes.
Product: Corvette Racing Sway Bars Part umbers: 1110212 Heavy Rate 1110213 C6 Z06 Heavy Rate 1110292 Light Rate Applications: Chevrolet Corvette, 1997 - Current Description: These racing sway bars are
More informationATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.
INSTALLATION MANUAL PROMASTER MOUNTING CHANNEL KIT (2115-0-01) ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT. 1/2 in Wrench/ Socket
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2013-UP FORD ESCAPE APP PART # 28-21010, 28-21015 STYLIZED RUNNING BOARD ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 RUNNING BOARDS
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067
INSTALLATION INSTRUCTIONS GRILLE GUARD 07-14 TOYOTA TUNDRA 08-14 TOYOTA SEQUOIA PART # P2067 PARTS LIST: GRILLE GUARD 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left
More informationLogo/Company Name 4 w x.75 h. Assembly Instructions. 1) Remove base, back/back bar, pneumatic cylinder, casters/glides, and seat from box.
w x. h ) Remove base, back/back bar, pneumatic cylinder, casters/glides, and seat from box. ) Put casters or glides on base. Use pressure to push in (). ) Slide optional foot ring () over pneumatic cylinder
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationINSTALLATION & OWNER S MANUAL
Rev. C, p. 1 of 24 INSTALLATION & OWNER S MANUAL HONDA PIONEER 700-4 ClearView Cab p/n: 1HONP7004CV fits model years up thru 2017 The contents of this envelope are the property of the owner. Be sure to
More informationINSTALLATION INSTRUCTIONS PART#: SR-DOR SPARTAN RUNNING BOARD DODGE SPRINTER (FULL SIZE) FREIGHTLINER SPRINTER (FULL SIZE) 10-16
INSTALLATION INSTRUCTIONS PART#: SR-DOR353296 07-09 DODGE SPRINTER (FULL SIZE) 07-16 FREIGHTLINER SPRINTER (FULL SIZE) 10-16 MERCEDES-BENZ SPRINTER (FULL SIZE) PARTS LIST: 1 Driver/left Spartan Running
More information(4) 12mm Plastic Retainers
PARTS LIST: Qty Description Qty Description 1 Driver/Left Sidebar 4 10-1.5mm x 35mm Hex Bolts 1 Passenger/Right Sidebar 4 10mm x 27mm OD x 3mm Flat Washers 1 Driver/Left Mounting Bracket 4 s 1 Driver/Left
More informationDriver/Left Rear Inner Support Bracket. (2) Front Bracket Arms
PARTS LIST: VIEWPOINT RUNNING BOARDS 1 Driver/Left Running Board 2 10mm Lock Washers 1 Passenger/Right Running Board 20 8mm x 25mm Hex Bolts 2 Mounting Bracket Arms 28 8mm x 22mm OD x 2mm Flat Washers
More informationLD1 FRONT BUMPER GMC SIERRA 1500
LDB-GSIE52-FB PARTS LIST: 1 LD1 Bumper Assembly 6 12mm Lock Washers 1 Driver/left Frame Mounting Bracket 6 12mm Hex Nuts 1 Passenger/right Frame Mounting Bracket 6 10-1.5mm x 35mm Hex Bolts 2 Tow Hook
More informationCAUTION. INSTALLATION INSTRUCTIONS Part Number Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck
INSTALLATION INSTRUCTIONS Part Number 69110 Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message
More information(2) 12mm x 40mm Short Low Profile Bolt Plates. (2) Spacer Washers. (4) 12mm Plastic Retainers. Passenger/Right Front.
PARTS LIST: 1 Driver/Left Running Board with 1 Rubber Backing (use on SX & Limited models) 4 12mm Plastic Retainer 1 Passenger/Right Running Board with 1 Rubber 4 12mm Lock Washer Backing (use on SX &
More informationPassenger/Right. Driver/Left. Driver/Left Side Frame. Mounting Bracket. (2) 12mm Double Nut Plates (models without tow hooks)
PARTS LIST: Qty Description Qty Description 1 Grille Guard 4 10-1.5mm x 30mm Hex Bolt 1 Driver/left Frame Bracket 8 10mm x 24mm OD x 2.2mm Flat Washer 1 Passenger/right Frame Bracket 4 10-1.5mm Nylon Lock
More informationSECTION 1 SEAT BACK SUPPORT INSTALLATION
TM REAR SEAT KIT IMPORTANT: Do not fully tighten hardware until instructed. Read through all instructions before beginning installation. PATRIOT SEAT INSTALLATION TABLE OF CONTENTS: Section 1 - Seat Back
More informationProPass-200 Top Dresser
Setup Manual Form No. 3365-184 Rev A ProPass-200 Top Dresser Model No. 44700-Serial No. 310000001 and Up Model No. 44701-Serial No. 310000001 and Up Model No. 44704 Model No. 44705 Model No. 44706 Model
More informationInstallation Instructions
L-PB L-PW Installation Instructions Component Checklist Arm Assembly (with pre-assembled Desk Clamp) Hardware Desk Single Rotation Limiter (x1) (x1) 2mm Allen (x1) Cable Clip (x4) Spacer Bush (x4) Fasteners
More informationTJ/LJ Metal Cloak Front Fender Flare Install Instructions Rev. A Page 1 of 16
TJ/LJ Metal Cloak Front Fender Flare Install Rev. A Page 1 of 16 READ FITTING INSTRUCTIONS IN FULL BEFORE INSTALLATION This article is sold without warranty expressed or implied. No warranty or representation
More informationMUSTANG TIGER CAGE INSTRUCTIONS MANUAL PAGE 1
2005-2011 MUSTANG TIGER CAGE INSTRUCTIONS MANUAL PAGE 1 Thank you for purchasing our 2005-2011 Mustang Tiger Cage. Please read through all of the instructions first and then start installing the kit. We
More informationNISSAN #2744. Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY
NISSAN 16K Industry Standard Rail Custom Mounting Kit #2744 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationMURPHY. Library Bed - Model # BC-2 Hardware. Cabinet Cut List - Assembly Procedure and Sequence. Fits all Single/Twin, Double/Full, Queen Beds
MWBS MURPHY WALLBED SYSTEMS INC. MURPHY Library Bed - Model # BC-2 Hardware Cabinet Cut List - Assembly Procedure and Sequence Fits all Single/Twin, Double/Full, Queen Beds 2010 Murphy WallBed Systems
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 1500350 Parts List 1 Driver / left inner fender liner 1 Passenger / right inner fender liner 4 Z-hanger brackets 1 Thread-set bolt, M6 1 Thread-set washer 1 Thread-set spacer 22 Hex
More informationINSTALLATION INSTRUCTIONS 5" BENT END SIDEBARS ROCKER PANEL MOUNT SILVERADO/SIERRA CREW CAB INCLUDES DIESEL W/DEF PART NUMBER
INSTALLATION INSTRUCTIONS 5" BENT END SIDEBARS ROCKER PANEL MOUNT PART NUMBER WB51010S WB51010B WB51019S WB51019B PARTS LIST: 1 Driver/left Sidebar 25 8-1.25mm x 25mm Hex Bolt 1 Passenger/right Sidebar
More informationDEBRISMASTER BATTERY & GAS SWEEPER REPLACEMENT PARTS LIST
BATTERY & GAS SWEEPER REPLACEMENT PARTS LIST COVER & CHASSIS ASSEMBLY PARTS DRAWING (SEE PAGE 8 FOR PARTS LIST) PAGE 1 PN 222720 - DebrisMaster Parts List - Printed in USA 06/29/07 DEBRISMASTER CONTROLS
More informationKAWNEER 1686 CONCEALED EXIT DEVICE
FEBRUARY, 2015 1 ROD AND CENTER CASE ASSEMBLY: 1) For inactive doors or doors without exterior cylinder, or doors without the need for exterior cylinder dogging, the removal of the cylinder dogging pawl
More information(4) 10mm x 35mm Bolt/8mm Nut Plates. (2) 12mm Double Nut Plates. (2) Center Mounting Brackets (use for driver or passenger side)
PARTS LIST: PREMIUM RUNNING BOARD Qty Description Qty Description 1 Driver/Left Running Board 8 10mm Lock Washers 1 Passenger/Right Running Board 4 10-1.5mm Hex Nuts 2 Driver/Left Mounting Brackets (front
More information6945 (12v) 6944 (24V) installation instructions
6945 (12v) 6944 (24V) installation instructions included: tools needed: Cordless drill Breezeeasy Fan Mounting brackets 1/4 Drill Bit 10mm Socket Hardware Pack 10mm Wrench Fuse Assembly Wire Stripper Crimper
More informationInstallation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit
Installation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit The purpose of this guide is to: 1. Describe mounting of MP2 equipment on Mounting Bracket (page 2). 2. Describe mounting
More informationLSS1U-144/7 FIBER OPTIC SPLICE SHELF INSTALLATION GENERAL CUSTOMER SERVICES REFERENCES TOOLS REQUIRED
OFS Fitel LSS1U-144/7 Fiber Optic 636-99-103-1 Instruction Sheet Splice Shelf Installation COMCODE 845 866 474 LSS1U-144/7 FIBER OPTIC SPLICE SHELF INSTALLATION GENERAL This instruction sheet provides
More informationSTOP. 44" High Speed Sweeper. Operator's Manual. Model No Safety Assembly Operation Maintenance Parts
Operator's Manual STOP 44" High Speed Sweeper Model No. 486.029 DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 CAUTION: Before using this product, read this manual and
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationINSTALLATION INSTRUCTIONS ELEVATION REAR BUMPER FORD SUPERDUTY F #PW016687
INSTALLATION INSTRUCTIONS #PW016687 PARTS LIST: 1 Elevation Bumper Assembly 2 Plastic Plugs for license plate mount 2 2-hole Spacer Plates (for tow hitch only) 8 4mm x 10mm Socket Head Screws 4 Sensor
More information(6) Plastic Retainers. Mounting Bracket
PARTS LIST: 1 Driver/Left Sidebar 5 12mm Hex Nuts 1 Passenger/Right Sidebar 6 10-1.5mm x 35mm Hex Bolts 1 Driver Mounting Bracket 6 10mm x 27mm OD x 3mm Flat Washers 1 Driver Support Bracket 6 s 1 Driver
More informationAssembling a Wall-Mounted CTS
CHAPTER 3 Revised: February 4, 2010, This chapter provides you with the information you need to assemble a wall-mounted CTS-500-37 and includes the following sections:, page 3-1 Installing the External
More information2 Driver/left Front/Rear Mounting Brackets 6 10mm Lock Washer 2 Passenger/right Front/Rear Mounting 6 10mm Hex Nuts
PARTS LIST: STX300 RUNNING BOARD BRACKET KIT 2 Driver/left / Mounting Brackets 6 10mm Lock Washer 2 Passenger/right / Mounting 6 10mm Hex Nuts Brackets 1 Driver/left Center Mounting Bracket 12 8-1.25mm
More informationCheck what you have received against the component checklist and hardware above.
SSS SSPW SSW SSPB SSB Component Checklist Installation Instructions SYSTEMA Systema Monitor Spring Arm HARDWARE Display Mounting Spacers (x4) 3/4mm Allen Keys Display Mounting Screws Arm Assembly VESA
More informationOFS LSS1U-864/ Instruction Sheet Fiber Optic Comcode: Splice Shelf Installation
OFS LSS1U-864/9 636-299-103-49 Instruction Sheet Fiber Optic Comcode: 848 461 620 Splice Shelf Installation LSS1U-864/9 FIBER OPTIC SPLICE SHELF INSTALLATION GENERAL This instruction sheet provides procedures
More informationH15P. Toyota Hilux A-DECK Dual Cab
Toyota Hilux A-DECK Dual Cab Page 1 of 14 Fitting Instructions Part Number H15 Toyota Hilux A-DECK Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationClub Car 1510 to Curtis 1268 Conversion
Club Car 1510 to Curtis 1268 Conversion Installation Instructions 62-12685501CKI Rev. 05 7/18/14 Page 1 of 7 1510 to Curtis 1268 Conversion Installation Instructions Before you start turn Tow/Run switch
More information