HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX
|
|
- Ezra Bennett
- 6 years ago
- Views:
Transcription
1 HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX Read and follow these special instructions along with the standard instructions carefully before installing or using this cover. NOTICE TO INSTALLER: Even if familiar with product, read special instructions prior to installation as improvements may be made without notice. Always handle components with care. When done, these special instructions must be given to the consumer. NOTICE TO CONSUMER: Before using this product, read special instructions. Save these special instructions for future reference. NOTE TO OWNER AND INSTALLER: 1. Side rails in this kit mount to the deck rail system with special bolt on brackets instead of standard clamps as shown in standard instructions. 2. Cover may disable or limit use of some deck rail systems.
2 PREPARATION TOOLS NEEDED Protective eyewear Ratchet with 10 mm, 7/16 and 1/2 sockets Torque wrench! CAUTION: Over torquing hardware may damage components. Do not use impact tools. 1. INSTALLING WEATHER SEAL A. Clean vertical surface above deck rail system from bulkhead to tailgate with alcohol pad on both sides. NOTE: For best adhesion, ensure surface is clean and air along with surface temperatures are above 60 o F. B. Peel segment of paper backing from one end of D weather seal. At rear of truck, align top of weather seal with top of box rail then adhere weather seal segment without backing to vertical surface above deck rail system. NOTE: Ensure the top of seal is flush with box rail. C. From tailgate to bulkhead, continue peeling paper backing and adhering weather seal to vertical surface above deck rail system until bulkhead gap. Bulkhead Weather seal Bulkhead gap Area above deck rail Weather seal Truck rear Deck rail D. At bulkhead gap, pull seal section through at downward angle. TIP: Leave paper backing on section to allow for seal placement. Once seal is in place, carefully peel paper backing without removing seal from gap. Angle seal downward at bulkhead gap NOTE: Angling the seal, allows water to drain. E. Trim excess weather seal from both ends. 2
3 2. ASSEMBLING SIDE RAIL A. Locate two side rail sections for DRIVER S side by finding identifying arrow marks at seam of side rail sections. The remaining two side rail sections are for the passenger side. Arrow points toward the truck cab. NOTE: Be aware, side rails require multiple brackets for installation: front, middle and rear. Ensure to use the correct bracket that corresponds with its rail position. Front bracket Middle bracket Rear bracket NOTE: Each side rail assembly requires two different rail shapes: straight and contoured. B. Assemble side rail by mounting middle bracket to inner seams with (2) 1/4-20 x 3/4 bolts, (2) flat washers, (2) lock washers and (2) nuts. C. Align side rails, finger tighten and ensure brackets can be adjusted in or out. NOTE: Middle bracket attaches to side rail through square slots. Front straight side rail Align side rail seams Rear contoured side rail 1/4-20 x 3/4 Bolt Square slot 1/4 Flat washer 1/4 Lock washer 1/4-20 Hex nut 3
4 2. ASSEMBLING SIDE RAIL (Continued) D. Install front bracket to side rail with (1) 1/4-20 x 3/4 bolt, (1) flat washer, (1) lock washer and (1) nut. Finger tighten and ensure brackets can be adjusted in or out. NOTE: Front bracket attaches to side rail through square slots. E. Install rear bracket to side rail with (1) 1/4-20 x 3/4 bolt, (1) flat washer, (1) lock washer and (1) nut. Finger tighten and ensure bracket can be adjusted in or out. NOTE: Rear bracket attaches to side rail through square slot. 3. INSTALLING SIDE RAILS A. Remove deck rail system plug at end of channel near tailgate. Square slot 1/4 Flat washer 1/4 Lock washer 1/4-20 Hex nut Square slot Rear bracket 1/4 Flat washer 1/4 Lock washer 1/4-20 Hex nut 1/4-20 x 3/4 Bolt Side rail Front bracket 1/4-20 x 3/4 Bolt Remove plug 4
5 3. INSTALLING SIDE RAILS (Continued) B. Use 10 mm socket with ratchet to remove 6 mm bolt near end of truck. Save 6 mm bolt for reuse in Step 3G on page 6. 6 mm Bolt C. Slide carriage bolt bracket with 5/16 x 1-1/4 carriage bolt into channel of deck rail system, insert one set per front and middle bracket. D. Reinsert deck rail system plug at end of channel near tailgate. Weather seal Deck rail system E. For front and middle brackets, position side rail against inside lip of box. Align carriage bolts with brackets on side rails. Push side rail forward until rail touches front of box. NOTE: Ensure contoured portion of side rail is at rear of truck. 5/16 x 1-1/4 Carriage bolt and bracket Align slot in bracket with carriage bolt F. Secure with 5/16 serrated nuts. Leave finger tight for now. 5/16 serrated nut 5
6 3. INSTALLING SIDE RAILS (Continued) G. Attach rear bracket to box with 6 mm bolt (removed in Step 3B on page 5). Leave finger tight for now. 6 mm bolt H. For front and middle brackets, align side rail edge with bracket edge then tighten 1/4-20 nut. NOTE: Before tightening middle bracket nuts, ensure side rail is flush and aligned. Align edge of side rail with edge of bracket Tighten 1/4-20 nut I. At front and middle bracket, set height according to standard instructions. J. Position side rail and bracket against box rail and tighten 5/16 serrated nut. Hold side rail level while tightening Tighten 5/16 serrated nut 6
7 3. INSTALLING SIDE RAILS (Continued) NOTE: Before proceeding, ensure weather seal contacts side rail and creates a seal. Weather seal under side rail K. For rear bracket, align side rail edge with bracket edge then tighten 1/4-20 nut. Align edge of side rail with edge of bracket Tighten 1/4-20 nut L. Position side rail and bracket against box rail and tighten 6 mm bolt. Hold side rail level while tightening Tighten 6 mm bolt M. Repeat to install side rail on opposite side. N. Torque 5/16 nuts on 5/16 x 1-1/4 carriage bolts to 20 ft-lbs. O. Torque 1/4-20 nuts on 1/4-20 x 3/4 carriage bolts to 10 ft-lbs. P. Torque 6 mm bolts to 8 ft-lbs. Q. For remaining cover installation, refer to standard instructions. 7
8 Product subject to change without notice _INIT
HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX
HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX Read and follow these special instructions along with the standard instructions carefully before installing or using
More informationJK8 Body Kit KIT CONTENTS 1 K
JK8 Body Kit KIT CONTENTS A B C 1 K6861352 D E G F H 2 K6861352 I M N J K L O P Q R S 3 K6861352 T U V W X Y CALL OUT PART NUMBER DESCRIPTION QUANTITY A P5156021 HARDTOP 1 B P5155997 BULKHEAD 1 C 1PH98/9TZZAE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing VANISH Roll-Up Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship. With proper care, your cover
More informationINSTALLATION INSTRUCTIONS AND OWNER S MANUAL
INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing the AlloyCover from WeatherTech. Manufactured with pride using superior quality materials and workmanship. With proper care, your cover
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing ACCESS Original Roll-Up Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship. With proper care, your
More informationTOYOTA TUNDRA BUMPER STEP ASSIST Preparation
Preparation Part Number: PT392-34140 Kit Contents 1 1 Linkage Assembly 2 1 Mounting Bracket 3 1 Step Pad 4 1 Hardware Bag 5 1 Bumper Support Bracket 6 1 Bumper Re-enforcement Bracket Hardware Bag Contents
More informationINSTALLATION INSTRUCTIONS AND OWNER S MANUAL
INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing the AlloyCover from WeatherTech. Manufactured with pride using superior quality materials and workmanship. With proper care, your cover
More informationLIMIT SWITCH SPECIAL INSTRUCTIONS
LIMIT SWITCH SPECIAL INSTRUCTIONS Use these instructions to install a limit switch. Read and follow these instructions along with the standard instructions carefully before installing or using tarp system.
More informationINSTALLATION & OWNER S MANUAL
Rev. B, p. 1 of 25 INSTALLATION & OWNER S MANUAL POLARIS RANGER RCS (for models XP or HD) (for model years 2009-) cab without doors kit (p/n 1POLRCWD) cab with doors kit (p/n 1POLRC) doors only kit (p/n
More informationWOC Mid Size Door Installation
WOC-10112 Mid Size Door Installation NOTE: If the Mid Size Ranger that you are installing this door system on is a 2010 or newer you will need to remove the sill plates and side nets. If the doors are
More informationTONNEAU INSTALLATION GUIDE
TONNEAU INSTALLATION GUIDE Warranty, Care & Maintenance Model 4056 Toyota Tacoma Double Cab 5' Short Bed 2005-Current (With Multi-Track System) EASY AS 1-2-3! NORMAL INSTALLATION TIME 30 MINUTES For Warranty
More informationTOYOTA TUNDRA BUMPER STEP ASSIST Preparation
Preparation Part Number: PT392-34140 Kit Contents Item # Quantity Reqd. Description 1 1 Linkage Assembly 2 1 Mounting Bracket 3 1 Step Pad 4 1 Hardware Bag 5 1 Bumper Support Bracket 6 1 Bumper Re-enforcement
More information100mm. Part# AA Rev CUSTOMER SUPPORT: Wash truck bed.
Wash truck bed. 1 2 TRI-FOLD TONNEAU INSTALLATION GUIDE Sold exclusively at AutoAnything.com Please contact 800-874-8888 with any questions, to claim your warranty, or to discuss a return. You can also
More informationALUMINUM FORD F BED LENGTH. Installation Instructions: DF4 TOOLS REQUIRED 2015-CURRENT FOLLOW #DECKEDUSA
Installation Instructions: DF4 ALUMINUM FORD F150 5 6 BED LENGTH 2015-CURRENT TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16 deep
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationKK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console)
KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for 2011-2016 FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console) TOOLS Needed: Phillips Screw Driver Power Drill with Drill Bits Trim panel
More informationCENTER BELT SYSTEM INSTALLATION INSTRUCTIONS CARCG121220
CENTER BELT SYSTEM INSTALLATION INSTRUCTIONS 2013+ DODGE CHARGER Distributed by CARCG121220 Important Notice: Read all instructions before starting the installation of the seat. Before drilling or installing
More informationINSTALLATION INSTRUCTIONS South Highway 11 Westminster, SC Toll Free (888) (864) FAX (864)
These instructions apply to the servicing of the Lift Technologies MaxiMizer Integral Sideshifters Cylinder Head. WARNING! Unless the steps in the following Installation Instructions are properly followed
More information2016 Toyota Tacoma INSTALLATION SHEET
2016 Toyota Tacoma INSTALLATION SHEET MISSING PARTS? call Extang at 1-800-877-2588 Any and all needed parts will be shipped to you directly. (DO NOT return whole kit to store) Drill Torx Driver-T30 Wrench
More informationINSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK
INSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK Load capacity: Up to 800 lbs. evenly distributed. Approximate Assembly and Installation Time: 60 min. (1 hr.) depending on truck
More informationINSTALLATION INSTRUCTIONS
Hardware: 12M x 40M hex head bolts Qty: 4 12M flat washers Qty: 8 12M lock washers Qty: 4 12M Ny-lock hex nuts Qty: 4 Extension bracket with bolt Qty: 2 8M Ny-lock hex nuts Qty: 2 8M Lock washer Qty: 2
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing a LOMAX TM Hard Tri-Fold or Professional Series Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship.
More informationTONNEAU COVER SPECIAL SHIM AND CLAMP INSTRUCTIONS
TONNEAU COVER SPECIAL SHIM AND CLAMP INSTRUCTIONS ATTENTION INSTALLER: Read and follow these special instructions along with the standard instructions in owners manual. For 2014-ON Chevy/GMC 1500 Half
More informationINSTALLATION & OWNER S MANUAL
Rev. L p. 1 of 16 INSTALLATION & OWNER S MANUAL V4262 CAMO (SOFT SIDED) CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner
More informationAssist Step Kit Installation (Side Assist Step)
Page 1 of 6 2015 Chevrolet Silverado - 2WD Cheyenne, Sierra, Silverado Accessory Installation Manual Accessories Exterior Trim Accessories Accessories Document ID: 2741491 Assist Step Kit Installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More information** DO NOT EXCEED THE RECOMMENDED VEHICLE TOWING WEIGHT RATING ** DODGE RAM 1500
10/3/2017 DODGE RAM 1500 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE
More informationINSTALLATION & OWNER S MANUAL
Rev. R p. 1 of 16 INSTALLATION & OWNER S MANUAL V4211 HARD SIDED CAB KIT and/or V4275 CAMO HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner.
More information2014-Current. Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16 socket, 7/32 Allen wrench
Installation Instructions Van: VNFD13TRAN65 FORD TRANSIT 148 WHEELBASE 2014-Current TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16
More informationTONNEAU COVER SPECIAL SHIM AND CLAMP INSTRUCTIONS
TONNEAU COVER SPECIAL SHIM AND CLAMP INSTRUCTIONS ATTENTION INSTALLER: Read and follow these special instructions along with the standard instructions in owners manual. For 2014-ON Chevy/GMC 1500 Half
More informationALUMINUM FORD F BED LENGTH. Installation Instructions: DF5 TOOLS REQUIRED 2015-CURRENT FOLLOW #DECKEDUSA
Installation Instructions: DF5 ALUMINUM FORD F150 6 6 BED LENGTH 2015-CURRENT TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16 deep
More informationTOYOTA RAV RUNNING BOARD
TOYOTA RAV4 2013 - RUNNING BOARD Part Number: 00016-42020 Accessory Code:TR1 Conflicts Mudguard Kit Contents Item # Quantity Reqd. Description 1 1 LH Board Assembly 2 1 RH Board Assembly 3 1 LH Rear Mounting
More informationSPECIAL INSTALLATION INSTRUCTIONS
SPECIAL INSTALLATION INSTRUCTIONS WARN 4X FLARES FRONT AND REAR '98 TOYOTA HILUX DUAL-CAB As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a specific purpose.
More informationWait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
2012 Camry DISASSEMBLY Hint: Report a problem with this article Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PRECAUTION NOTICE: After turning the
More informationMODEL 2604 WARNING <THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> Custom 5th Wheel Hitch Mounting Rail Installation Instructions
B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 P:620.473.3664 F:620.869.9031 Custom 5th Wheel Hitch Mounting Rail Installation Instructions
More informationEXPRESS/SAVANNA 155 WHEELBASE. Installation Instructions Van: VNGM96EXSV65 TOOLS REQUIRED 1996-CURRENT. follow us : CHEVROLET & GMC
Installation Instructions Van: VNGM96EXSV65 CHEVROLET & GMC EXPRESS/SAVANNA 155 WHEELBASE 1996-CURRENT TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver,
More informationBolt-On/Rugged Fender Flares Nissan Titan (04-15) Please read instructions entirely before installing this product.
Please read instructions entirely before installing this product. Hardware Included QTY FUEL DOOR CLIP 1 Bolt Kit Included QTY ALCOHOL TOWELETTE 4 M4 SCREW 1 ALLEN KEY BOLT 42 CLIP.9MM 2 ABRASIVE RESISTANT
More informationPARTS LIST: Components. ` Bi-Fold Tonneau Cover
` Bi-Fold Tonneau Cover Fits: 2004-2014 TFX3401 - Ford F150 5.5 2004-2014 TFX3402 - Ford F150 6.5 2015 TFX3403 - Ford F150 5.5 2015 TFX3404 - Ford F150 6.5 1999-2007 TFX3405 - Ford F250/F350 6.5 2008-2015
More information2 Driver/left Front/Rear Mounting Brackets 6 10mm Lock Washer 2 Passenger/right Front/Rear Mounting 6 10mm Hex Nuts
PARTS LIST: STX300 RUNNING BOARD BRACKET KIT 2 Driver/left / Mounting Brackets 6 10mm Lock Washer 2 Passenger/right / Mounting 6 10mm Hex Nuts Brackets 1 Driver/left Center Mounting Bracket 12 8-1.25mm
More informationInstallation Instructions Vanishing Lid Bracket
-800-447-88 www.coverpools.com Installation Instructions Vanishing Lid WARNING FOR YOUR SAFETY This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment
More informationInstallation Instructions Supertop for Truck
Installation Instructions Supertop for Truck US Patent 6827391 Vehicle Application: Toyota Tacoma Double Cab 2005-2011 (5 ft.) Part Number: 76308 INSTALLATION TIME SKILL LEVEL 1-1/2 Hours 2 - Moderately
More information2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete E
BILLET GRILLS IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete 5122-1900-11E TOOLS REQUIRED Automotive
More informationLOCKN LOAD MOUNTING KIT
LOCKN LOAD MOUNTING KIT TM VOLKSWAGEN AMAROK 2 BAR FIXED POINT HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES + CARGO FIRST TIME INSTALLATION
More informationInstallation Guide CLAAS Lexion Combines with 9 inch Elevators
Installation Guide CLAAS Lexion Combines with 9 inch Elevators 955614_01 4/17 1 Table of Contents System Overview 3 Quick Start Guide 4 Flow Sensor Installation 5 Hydraulic Elevator Adjustment Kit Installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SIDE UNDER S Application 2013 CIVIC 2-DOOR Publications No. AII 13069 Issue Date NOV 2012 PARTS LIST 4 Flare nuts Left spoiler 2 Washer-nuts Right spoiler 2 Screws 2
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationINSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER
Form 5063T, 06-05 Supersedes Form 5063T, 02-04 INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER This document provides the information needed to install the DSP9600/9100 Wheel Balancer. NOTE:
More informationMOUNTING KIT MKPBX
MOUNTING KIT 53221-MKPBX Toyota Tacoma (4x4) (2005-2015) Mounting Kit 53221-MKPBX Item Part # Description MKPBX X-MKB 1 52638-D-GA Lift Frame Galvanized 1 2 50069-C-GA Lift Channel Galvanized 1 3 HH-00972-153
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationN. 15th Street, Middlesboro, KY TARP-N-GO SYSTEMS INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 TARP-N-GO SYSTEMS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Tarp Tarp-N-Go tarping system. With tarping systems
More informationMULTI-POLE MOUNT LARGE GROUND MOUNT. Assembly Instructions. Assembly Instructions. step-by-step assembly and installation
MULTI-POLE MOUNT Assembly Instructions LARGE GROUND MOUNT Assembly Instructions step-by-step assembly and installation PCN 081711-2 The Large Ground Mount A few words about the product The Large Ground
More information2019-ON RAM 1500 INSTALLATION INSTRUCTIONS
2019-ON RAM 1500 INSTALLATION INSTRUCTIONS Thank you for purchasing ROCKSTARTM Splash Guard Mud Flaps. Agri-Cover, Inc. proudly manufactured these mud flaps using superior quality materials and workmanship.
More informationDODGE RAM Current
Installation Instructions Van: VNRA13PROM65 DODGE RAM PROMASTER 159 WHEELBASE 2014-Current TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket,
More informationINVIS-A-RACK INSTALLATION INSTRUCTION DZ , DZ , DZ IR-HOUSING-ASSEML X2 IR-HOUSING-ASSEMR X2 8 FT.
A INVIS-A-RACK INSTALLATION INSTRUCTION DZ 951550, DZ 951600, DZ 951800 DRIVER FRONT / PASSENGER REAR B PASSENGER FRONT / DRIVER REAR IR-HOUSING-ASSEML X2 IR-HOUSING-ASSEMR X2 BUNGEE BOX MOUNTING HOOK
More informationINSTALLATION & OWNER S MANUAL
Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when
More informationRAM 1500, 2019 CLASSIC & 2010-ON 2500/3500 INSTALLATION INSTRUCTIONS
2009-18 RAM 1500, 2019 CLASSIC & 2010-ON 2500/3500 INSTALLATION INSTRUCTIONS Thank you for purchasing ROCKSTARTM Splash Guard Mud Flaps. Agri-Cover, Inc. proudly manufactured these mud flaps using superior
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> Custom 5th Wheel Hitch Mounting Rail Installation Instructions
B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 P:620.473664 F:620.869.9031 Custom 5th Wheel Hitch Mounting Rail Installation Instructions
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE
More informationINSTALLATION INSTRUCTIONS AND PARTS LIST
1. READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS (LISTED ON SERVICE PARTS LIST) ARE ON HAND BEFORE STARTING THE INSTALLATION. 2. PEEL AWAY THE PROTECTIVE VINYL COVERING AND
More informationToyota Tacoma Double Cab up A Toyota Tacoma Access Cab* up A. 3-5 Hours INSTALLATION GUIDE INSTALLATION TIME SKILL LEVEL
INSTALLATION GUIDE APPLICATION MODEL YR PART # Toyota Tacoma Double Cab 2005 - up 75142-01A Toyota Tacoma Access Cab* 2005 - up 75142-01A INSTALLATION TIME 3-5 Hours Professional installation recommended
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing TONNOSPORT Roll-Up Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship. With proper care, your cover
More informationFORD SUPER DUTY 6 9 BED LENGTH. Installation Instructions: DS1 TOOLS REQUIRED FOLLOW #DECKEDUSA
Installation Instructions: DS1 FORD SUPER DUTY 6 9 BED LENGTH 1999-2008 TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16 deep socket,
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL This Curtis Cab is designed and manufactured for use only as reasonable weather protection. This cab is not applicable, Nor should the cab be considered as protection against
More informationParts List ILLUSTRATION #1
Installation Instructions BR20 Rear Bumper Replacement Part Number 28295T 2015-2016 Ford F-150 2/4WD Do not attempt to install this product on any vehicle other than the one listed above! Parts List Item
More informationJEEP Wrangler JK/JKU Swing-A-Way Tire Carrier/RotoPpax WARNINGS/CAUTIONS NOTE. INSTALLATION INSTRUCTIONS 2 Door Models 85209
JEEP Wrangler JK/JKU Swing-A-Way Tire Carrier/RotoPpax 2007-2017 INSTALLATION INSTRUCTIONS Item Kit No. 2 Door Models 85209 4 Door Models 85209 WARNINGS/CAUTIONS These instructions are for both the can
More informationINSTALLATION & OWNER S MANUAL
Rev. C, p. of 2 INSTALLATION & OWNER S MANUAL KUBOTA B2650/3350 Hard Sided Cab p/n KB33AS Soft Sided Cab p/n KB33SS Installation Instructions The contents of this envelope are the property of the owner.
More information(W) INSTALLATION INSTRUCTIONS 90DEG BENT END SIDEBARS F-150 SUPER CREW CAB PART #DZ /DZ /DZ
(W) INSTALLATION INSTRUCTIONS PART #DZ 371691/DZ 371692/DZ 371693 PARTS LIST: Qty Description Qty Description 1 Driver/Left Sidebar 2 12mm x 45mm Double Bolt Plates 1 Sidebar 4 s 1 Driver/Left Mounting
More informationINSTALLATION & OWNER S MANUAL
p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger 400-EV PathPro SS Cab (fits 2010 - current) (p/n: 1PRG400FS) The contents of this envelope are the property of the owner. Be sure to leave with the
More information6 Inch Oval Step Board
` 6 Inch Oval Step Board Part No. G9001B-1 Fits: 1999-2013 Chevrolet Silverado / GMC Sierra 1500/2500/3500 HD ( All Cabs ) REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 35-45 min Cutting Required
More informationINSTALLATION INSTRUCTIONS JK DECK ENCLOSURE #326 (2 & 4 Door)
SHIPMENT CONTENTS INSTALLATION INSTRUCTIONS JK 2011+ DECK ENCLOSURE #326 (2 & 4 Door) Please read and fill out the enclosed warranty registration card to activate your warranty. #3 Lid #7 Front Panel #4
More informationTOYOTA TUNDRA SKID PLATE Preparation
Preparation Part Number: PT98-4140 Kit Contents Item # Quantity Reqd. Description 1 1 Skid Plate (Pre-Assembled with Hardware) 2 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1
More informationPart Number: TBL-016S
5/18/17 TOYOTA TACOMA 2016-2017 LED Bed Light Kit Part Number: TBL-016S Kit Contents Item # Quantity Reqd. Description 1 2 LED Bed Light Harness (10 ) 2 2 LED Bed Light Harness (5 ) 3 1 Y Harness Extension
More informationPassenger/Right Support Bracket Driver/Left Support Bracket
PARTS LIST: 1 bumper 24 12mm x 37mm OD x 3mm Flat Washers 1 Driver/left Mounting Bracket 14 12mm Lock Washers 1 Passenger/right Mounting Bracket 14 12mm Hex Nuts 1 Driver/left Lower Support Bracket 2 Plastic
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory FABRIC FRONT DOORS P/N 0SR90-HL4-211A (BLACK) P/N 0SR90-HL4-221A (CAMO) Application SXS1000M3/M3P/M5P/M5D Honda Dealer: Please give a copy of these instructions to your
More informationINSTALLATION & OWNER S MANUAL
Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Left front trim piece
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More informationMobtown Offroad Toyota Tacoma Bolt On Rock Slider Installation Instructions
Mobtown Offroad 2005+ Toyota Tacoma Bolt On Rock Slider Installation Instructions Tools Needed: 9/16 Box Wrench 9/16 Standard and Deep Well Socket, 3/8 Drive Ratchet, 3/8 Drive 3/4 Standard Socket 3/4
More informationI-317. AWWA Check Valves WARNING INSTALLATION AND MAINTENANCE INSTRUCTIONS SERIES 317 WARNING
Read and understand all instructions before attempting to install, remove, adjust, or perform maintenance on any Victaulic piping products Wear safety glasses, hardhat, and foot protection. Failure to
More informationINSTALLATION INSTRUCTIONS AND PARTS LIST MODEL BRACKET PACKAGE TO MOUNT O-MEGA STEPS/GRIP STEPS VEHICLE APPLICATION: 2001 AND NEWER FORD VANS
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL 570124 BRACKET PACKAGE TO MOUNT O-MEGA STEPS/GRIP STEPS VEHICLE APPLICATION: 2001 AND NEWER FORD VANS READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350
6065 SUBKIT 7/7/0 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-50, F-50 PAGE OF WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR
More informationInstallation Instructions Bolt-On Fender Flares Ford F150 (09-12) Part #17394
Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 29.5ft ALCOHOL TOWELETTE 4 BLACK HEX BOLT 42 RETAINING CLIP.9mm
More informationParts List. Item Qty. Part # Description Item Qty. Part # Description Torque. 1 1 Bumper Replacement Shell 10 4 ½ x 1 ½ Hex Bolt 65 Ft.
Installation Instructions BR20 Rear Bumper Replacement Part # 28371T 2011-2016 Ford F-250 & F-350 Super Duty 2/4WD Do not attempt to install this product on any vehicle other than the one listed above!
More informationInstallation Instructions
Installation Instructions CUSTOM QUICK INSTALL MOUNTING KIT 2011 & UP Ford Super Duty F-250/F-350/F-50 2011 & UP Part Number: 50073 WARNING: Under no circumstances do we recommend exceeding the towing
More informationMISSING PARTS? call Extang at
MISSING PARTS? call Extang at 1-800-877-2588 Any and all needed parts will be shipped to you directly. (DO NOT return whole kit to store) 1/2 Socket Wrench 3/4 Sheetmetal Drill Bit #2 Phillips Screwdriver
More informationMon - Thurs 7:30am - 5:00pm Friday 7:30am - 4:00pm CST PLEASE INSPECT YOUR PRODUCT FOR DAMAGE BEFORE PROCEEDING TO INSTALLATION
1-800-779-2102 Mon - Thurs 7:30am - 5:00pm Friday 7:30am - 4:00pm CST PLEASE INSPECT YOUR PRODUCT FOR DAMAGE BEFORE PROCEEDING TO INSTALLATION INSTRUCTIONS FOR RETURNS: ALL PRODUCTS NEED RETURNED TO THE
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Item Qty. A B C D E F G H 1 Bedliner Under Rail Bedliner Titan Crew Cab/King Cab/Single Cab 999T1 W3700, 999T1
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350
60647 SUBKIT 7/3/204 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350 PAGE OF 4 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE
More informationPassenger/Right Top Support Bracket. (2) 10mm Nut Plates
PARTS LIST: 1 Extreme Grille Guard 16 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 10 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 10 12mm Hex Nuts 1 Driver/Left
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 2051108 Parts List 1 Driver / left running board 1 Passenger / right running board Level of Difficulty Easy Scan for helpful install tips 2 Mounting bracket, front 2 Mounting bracket,
More informationF Ext Cab 40/20/40 w/ integral seatbelt Installation
2001-07 F-250-350 Ext Cab 40/20/40 w/ integral seatbelt Installation Step 1. Driver and Passenger Tops/DT & PT: Temporarily remove the headrests by lifting them up all the way. Then with slight upward
More informationINSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT
INSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT P FRONT 1 with MFK 4 for 2008 2019 CHEVROLET PASSENGER VANS W/DUAL SIDE SWING OUT DOORS P FRONT 2 with MFK 8 for 2008 2019 CHEVROLET
More information2007-Current. Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16 socket, 7/32 Allen wrench
Installation Instructions Van: VNMB07SPRT55 MERCEDES BENZ / DODGE / FREIGHTLINER SPRINTER VAN 144.3 WHEELBASE 2007-Current TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench,
More informationTOOLS REQUIRED. INSTALLATION INSTRUCTIONS TRUCK MODEL: DT1 TOYOTA TUNDRA 5 7 bed length 2007-current year. NOTE: These might actually be useful
INSTALLATION INSTRUCTIONS TRUCK MODEL: DT1 TOYOTA TUNDRA 5 7 bed length 2007-current year VERSION 1.5 TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver,
More informationBefore starting installation
Before starting installation The load rating for these tire-can/tire carriers is a MAXIMUM of 175 lbs. Please be aware that some tire and wheel combinations along with gas cans and hi-lift jacks can exceed
More information(2) Support Brackets (fit left or right) (2) 12mm x 40mm Bolt Plates
PARTS LIST: 1 bumper 6 12-1.75mm x 160mm Hex Bolts 2 Frame Mounting Brackets (fit left or right) 2 12-1.75mm x 50mm Hex Bolts 2 Support Brackets (fit left or right) 18 12mm x 37mm OD x 3mm Flat Washers
More informationGenesis Roll Up Tonneau Cover
Installation Instructions Genesis Roll Up Tonneau Cover or proper installation and best possible fit, please read all instructions EORE you begin. Contents Cover ssembly river Side Rail C Passenger Side
More informationTONNEAU INSTALLATION GUIDE
TONNEAU INSTALLATION GUIDE Warranty, Care & Maintenance Model 1080 GMC Sierra Ext/Crew Cab 5.7' Short Bed 2007-Current EASY AS 1-2-3! NORMAL INSTALLATION TIME 30 MINUTES For Warranty Issues, Contact UnderCover
More informationINSTALLATION & OWNER S MANUAL
Rev. D, p. 1 of 14 INSTALLATION & OWNER S MANUAL Bobcat CT 230 and KIOTI CK30 cab kit with hard doors and soft rear curtain p/n 1BCT230 & 1KTCK30 The contents of this envelope are the property of the owner.
More information2 Rubber Bumper GSM MM nut GSM30201 K9-F18-PT_INST_4-16
K9-F18-PT INSTALLATION INSTRUCTIONS K9 Kit for 2013-2019 FORD INTERCEPTOR UTILITY Vehicle Notes: 1. For K9 applications, it is recommended to order the Interceptor Utility with the OEM optional Aux Rear
More information