INSTRUCTION GUIDE 6795
|
|
- Debra Chambers
- 5 years ago
- Views:
Transcription
1 with a 402 Uni Pro Seat and Air Suspension in a RowCrop Series or WD Series Tractor with Sound-Gard Cab Hydraulic plug 5/16-18 x1 Bolt 1. Remove the original seat and suspension. 2. Cap the hydraulic lines with the nuts and plugs provided. Cut and plug the breather line by turning a 5/16 x 1 bolt into the tube. 3. Bolt the slide rails to the suspension with four 8mm x 12mm bolts. The slide rail lever must be assembled on the left side of the seat and suspension. Note: Use the slide rails that were shipped with PN: Remove and discard the slide rails that are attached to the seat. 8mm x 12mm Bolts page 1
2 5/16 X 3/4 FLAT HEAD SOCKET CAP SCREWS Installation Instructions to Replace a JD Deluxe Seat Suspension with a 402 Uni Pro Seat and Air Suspension in an Early 30 Series Row Crop Tractor with Sound-Gard Cab 1. Bolt the 6080 SAP to the slide rails with four 5/16 x 3/4 flat head socket cap screws, and 5/16 jam nuts. Place three washers in between the slide rails and SAP 6080, one on each bolt. Two on the right slide rail and one on the rear hole of the left slide rail to allow the SAP 6080 to sit level. Use holes so the SAP 6080 is offset to the right. 5/16 FLAT WASHERS 5/16-18 page 2
3 with a 402 Uni Pro Seat and Air Suspension in a RowCrop Series or WD Series Tractor with Sound-Gard Cab 1. Bolt the suspension to the PED 44 with four 5/16 x 5/8 bolts and flange nuts. You will have to unhook the rubber boot from the bottom of the suspension to get inside and fasten the nuts. It will help to air the suspension up to allow for some room to get inside the suspension. 2. Bolt the PED 44 and suspension to the cab deck with the original bolts. 5/16-18x5/8 Hex Head Bolts 5/16-18 Flange Nuts page 3
4 INSTRUCTION GUIDE 6796 Optional Swivel Instructions If no swivel go to page 5. with a 402 Uni Pro Seat and Air Suspension in a RowCrop Series or WD Series Tractor with Sound-Gard Cab 1. Install the Grammer Swivel. This can be installed two different ways. The lock lever can be installed to the front or rear left of the seat. If you plan on locking the swivel to move freely it is recommended to install the lever to the rear left. When the lever is installed to the front left and locked out, it can hit the tractor seat platform when driving on rough terrain (depending on where the seat is located fore and aft). 2. Place the swivel onto the SAP If you are installing the swivel lock lever to the front left the square part of the swivel will go against the SAP For the lock lever to the rear left, place the rectangular side of the swivel against the SAP The swivel should be centered side to side and the front edge should be close to flush with the SAP Locate the four mounting holes and break the plastic knockouts from the swivel. Fasten the swivel down using four 5/16 x 5/8 socket head cap screws, lock washers, and jam nuts. The lock washer goes on the screw first, then through the swivel and SAP 6080 with the jam nut on the bottom. Tighten the bolts. 5/16-18x5/8 Socket Head Cap Screw 5/16-Lock Washer 5/16-18Jam Nuts Phone / Web Site page 4A
5 with a 402 Uni Pro Seat and Air Suspension in a RowCrop Series or WD Series Tractor with Sound-Gard Cab 1. Install the seat. Remove the seat cushion by removing the two screws from the bottom front of the seat. Place the seat onto the swivel. NOTE: If the swivel was installed with the lock lever to the front left, you will have to place the 5/16 x 1 1/8 flat bar that came with the swivel onto the rear channel of the swivel plate. Center the seat so that two front holes and two rear holes line up. Remove the plastic knockouts from the swivel where the seat holes line up. NOTE: If the lock lever on the swivel is on the front left the rear seat holes will line up with the holes on the flat bar. Fasten the seat down using two 5/16 x 5/8 socket head screws and flange nuts on the front. If the swivel lock lever was installed to the front left, use two 5/16 x 1 flat head socket cap screws and flange nuts on the rear two holes. If the swivel lock lever was installed to the rear left, use another two 5/16 x 5/8 socket head cap screws and flange nuts. Tighten all hardware. 2. Reinstall the seat cushion. 5/16-18 Flange Nuts Flat Bar Spacer 5/16-18x1 Flat Head Socket Cap Screws 5/16-18x5/8 Socket Head Cap Screws page 4B
6 with a 402 Uni Pro Seat and Air Suspension in a RowCrop Series or WD Series Tractor with Sound-Gard Cab 1. Install the seat. Remove the seat cushion by removing the two screws from the bottom front of the seat. Place the seat onto the SAP Center the seat so that two front holes and two rear holes line up. 2. Fasten the seat down using two 5/16 x 5/8 socket head screws and flange nuts on the front and back. Tighten all hardware. 3. Reinstall the seat cushion. 4. Connect the suspension to to a power source and ground. 5/16-18 Flange Nuts 5/16-18x1 Flat Head Socket Cap Screws page 5
INSTRUCTION GUIDE 6793
1. Remove the old seat and suspension. 2. For models with the slanted front section on the seat well, bolt the PED JD W43A plate to the bottom of the PED JD W43 with two 5/16 x 3/4 carriage bolts and flange
More informationINSTRUCTION GUIDE 6791
John Deere 30 Series Seat Well Extension Kit for tractors with 7 1/2 wide seat well Installation Instructions to Replace a JD Deluxe Seat Suspension with a 402 Uni Pro Seat and Air Suspension in an Early
More informationSubject: Chassis and Cab Power Distribution Center Nylon Washers Product: Medium Terminal Tractor. Date: 24-JUN-2016
Page 1 of 11 Units Affected: All Kalmar Ottawa T2 model terminal tractors built prior to October 13, 2015. Possible Situation: The fasteners for the cab and chassis power distribution boards may abrade
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationRT1 DUAL OUTLET SLIP-ON EXHAUST HONDA CBR600RR Rev B
18-1022-723-02 08 50 44541 Rev B PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00042 Slip-on S-bend Assembly 1 2) 00-200-01197 Stainless Steel Dual Outlet Muffler 1 3) 03-46-42766 Muffler Mounting
More informationTJ 231/241 CABLE SHIFTER
KIT CONSISTS OF: # Qty Part No. Description P.O. Box 247, 4320 Aerotech Center Way PAGE 1 OF 10 Page Rev. Date: 08-29-16 1 1 300474 WASHER-RUBBER YOKE SEAL 32 SPLINE 2 1 300476 NUT- 7/8"-20 FLANGE LOCKNUT
More informationPLOW MOUNT GLACIER PRO KIT
PLOW MOUNT GLACIER PRO KIT P/N 2880262 APPLICATION FOR USE WITH THE GLACIER PRO MID-SIZE PLOW SYSTEM (P/N 2880260) ON 2015 AND NEWER RZR 00 MODELS BEFORE YOU BEGIN Read these instructions thoroughly and
More informationINDUSTRY STANDARD BASE RAIL UNIVERSAL MOUNTING KIT PART NUMBER 2720
INDUSTRY STANDARD BASE RAIL UNIVERSAL MOUNTING KIT PART NUMBER 2720 INSTALLATION INSTRUCTIONS Introduction The following steps provide general and vehicle-specific instructions for the installation of
More informationGLACIER PRO PLOW FRAME KIT
GLACIER PRO PLOW FRAME KIT P/N 2883255 APPLICATION All 2009 and newer RANGER XP Full installation of the Glacier Pro plow system requires a winch with an auto-stop fairlead and a synthetic winch rope or
More informationCAN AM. Version 1. Version Outlander 400, 500, 650, 800 and Outlander Max Renegade 500/ Outlander 800R/1000R
CAN AM 00-4 Outlander 400, 500, 50, 800 and Outlander Max 007-4 Renegade 500/800 0-4 Outlander 800R/000R BLADE HARDWARE MOUNTING INSTRUCTIONS P/N: 450-04 CUSTOMER MUST RECEIVE A COPY OF THIS INSTRUCTION
More information62 Deck Idler Kit High Speed
Part No. 00 FORM NO. -899 6 Deck Idler Kit High Speed For Model 70 Serial No. 99000 to 99000 For Model 7 Serial No. 9900 to 99000 INSTALLATION INSTRUCTIONS Loose Parts Note: Use the chart below to identify
More informationFM-170 DRIVE ASSEMBLY REBUILD KIT (P/N )
FM-1 70 Drive Assembly Rebuild Instruction Sheet 46-85 And Idler Bearing Assembly Replacement Page 1 FM-170 DRIVE ASSEMBLY REBUILD KIT (P/N 118 800) Description The following procedure details the rebuild
More information07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714-630-0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: K886764 07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES PARTS LIST QTY LIFT
More informationcfr angle kit INSTALLATION INSTRUCTIONS: 2009-present nissan 370z z infiniti g37 v36 Part Numbers: VOO-akns-0400
cfr angle kit INSTALLATION INSTRUCTIONS: 2009-present nissan 370z z34 2008-2013 infiniti g37 v36 Part Numbers: VOO-akns-0400 We recommend that installation of all Voodoo13 parts be completed by a professional
More informationINSTALLATION & OWNER S MANUAL
Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave
More informationHP10220 KIT. See application guide for proper fitment.
HP10220 KIT Dodge Dakota* (2WD/4WD) * 2005 All Dodge Dakotas 2006 - All Dodge Dakotas except Night Runner and R/T sub models 2007 - All Dodge Dakotas except SXT and TRX4 sub models 2008 - All Dodge Dakotas
More informationKinze 3000 Series Row Unit. Hydraulic Actuator Installation Instructions PN: ENG REV. A
Kinze 3000 Series Row Unit Hydraulic Actuator PN: 2006428-ENG REV. A Installation Overview Required Parts Part Number Qty * Description 4003011 1 HYDRAULIC ACTUATOR ASSY. (INCLUDES MOUNTING HARDWARE) 4003458
More informationINSTRUCTIONS (DROP PIN KIT FOR REPLACEMENT CABLE)
LIFT CORPORATION Sht. 1 of 6 DSG# M-14-48 Rev. - Date: 06/15/16 INSTRUCTIONS (DROP PIN KIT FOR REPLACEMENT ) C1 DROP PIN ASSEMBLY, P/N 295507-01 (10512) RETAINING RING 5/8 DIA. P/N 905004-07 PIN WELDMENT
More informationVALVE AND PLUMBING KIT INSTRUCTIONS SMC 84Q & 2408 LOADERS NEW HOLLAND TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB 1720 X X X 1920 X X X
ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT INSTRUCTIONS SMC 84Q & 2408 LOADERS NEW HOLLAND TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB 1720 X X X 1920 X X X TRACTOR AND VALVE KIT GENERAL
More informationTRACK EXTENSION KIT P/N OWNER S MANUAL ATTENTION DEALER: CUSTOMER MUST RECEIVE A COPY OF THIS MANUAL AT THE TIME OF SALE.
TRACK EXTENSION KIT P/N 33-0300 OWNER S MANUAL Application PLOW PUSH TUBE NO. 33-0000, 33-0070, 34-0000, 34-0070 ATTENTION DEALER: CUSTOMER MUST RECEIVE A COPY OF THIS MANUAL AT THE TIME OF SALE. Before
More informationIllustrated Parts Manual
Illustrated Parts Manual Models 522D LoPro 524D LoPro S/N 0900 P/N - 948-403 Revised July 6, 2007 INTRODUCTION Table of Contents SECTION INTRODUCTION Table of Contents... - thru -4 Alphabetical Index...
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 TRANS 4 FRONT CAB KIT (p/n: KAF40T-001WA and p/n: KAF40T-001BA) NOTE: Hard sided doors, soft sided doors, and rear cab are sold
More informationTOYOTA 4-RUNNER TOWING HITCH Preparation
Preparation Part Number: PT228-89460 Kit Contents 1 1 High Assembly 2 1 Wiring Harness Bracket 3 1 Hardware Bag 4 1 Hitch Cover 5 2 Frame Spacer 6 2 Center Spacer 7 1 Close-out Panel Hardware Bag Contents
More informationSERVICE INFORMATION LETTER
SERVICE INFORMATION LETTER DATE: August 19, 2015 SERVICE INFORMATION LETTER NO. 0183 Page 1 of 18 1. SUBJECT: Collective Stick Socket Replacement 2. MODEL: F28A, 280, F28C, 280C, F28F, 280F, and 280FX
More informationOPERATION WARNING WARNING
OPERATION WARNING WARNING SERIOUS INJURY MAY OCCUR IF HEAD CLEARANCE IS NOT ADEQUATE. BEFORE DRIVING OR RIDING IN VEHICLE, ENSURE THAT THERE IS ADEQUATE HEAD CLEARANCE AT THE MAXIMUM UPWARD TRAVEL OF SEAT.
More informationInstallation Instructions
DODGE 20K Industry Standard Rail Custom Mounting Kit #2742 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationFIELD & BRUSH MOWER SERIES 0
Parts Manual for SERIES 0 MODEL FB13250BS FB13250BV FB15250KW McDonough, GA, 30253 U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 1, 8/30/2005 Table Of Contents PAGE GROUP
More informationLankota, INC. LAN Installation Instructions
Lankota, INC. LAN - 84206 Converts 600 Series Platform Heads to 50 Series & Earlier Model Combines. Installation Instructions Kit LAN84206 Lankota is the trademark of Lankota, Inc. 1 LAN 84206 Parts break
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationAutoFarm GPS AutoSteer Hardware Installation Guide
AutoFarm GPS AutoSteer Hardware Installation Guide Supported Models: John Deere 9120 Wheeled John Deere 9220 Wheeled John Deere 9320 Wheeled John Deere 9420 Wheeled John Deere 9520 Wheeled John Deere 9620
More informationADVANCE ADAPTERS INC. P/N: TJ 231/241 CABLE SHIFTER
Paso Robles, CA 93447 PAGE 1 of 10 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 09-25-15 KIT CONSISTS OF: # Qty Part No. Description 1 1 300474 WASHER-RUBBER YOKE SEAL 32 SPLINE 2 1 300476
More informationPart # Impala TQ CoilOver Suspension Package
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11040311 58 Impala TQ CoilOver Suspension Package Front Components: 1 11053511 TQ Series Front Coilovers
More informationDetroit Speed, Inc. Rear Coilover Tower Brace Kit Camaro P/N:
Detroit Speed, Inc. Rear Coilover Tower Brace Kit 2016+ Camaro P/N: 042433 The Detroit Speed, Inc. 2016+ Camaro Rear Coilover Tower Brace Kit is a bolt-in design that increases overall vehicle stiffness.
More informationDo not have any open flame or heat sources close to the installation
March 6, 2017 IS# 791 Page 1 of 16 Thank you for purchasing a Transfer Flow, Inc. 50-gallon replacement fuel system for your 2011-16 Ford diesel short bed pickup. This system will fit any 2x4 or 4x4 crew
More information3 Dualsport rear suspension ram truck 2500 AIR RIDE. AEV30262AA Last Updated: 07/11/17 INSTALLATION GUIDE
3 Dualsport rear suspension ram truck 2500 AIR RIDE AEV30262AA Last Updated: 07/11/17 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm Socket Hack Saw
More informationASSEMBLY MANUAL SMC 2491 LOADER VALVE AND PLUMBING KIT INSTRUCTIONS KUBOTA TRACTORS
ASSEMBLY MANUAL Keep With Loader Operator's Manual SMC 2491 LOADER VALVE AND PLUMBING KIT INSTRUCTIONS KUBOTA TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB L5450 X X Valve and plumbing kit can be installed
More informationINSTALLATION INSTRUCTIONS `64 ½ - 70 MUSTANG, HEIDTS IFS, PRO-G GEN II P/N: MTF-201
INSTALLATION INSTRUCTIONS `64 ½ - 70 MUSTANG, HEIDTS IFS, PRO-G GEN II P/N: MTF-201 Please read these instructions completely Before starting your installation. Assemble suspension on vehicle before powder-coating
More informationDetroit Speed, Inc. Rear QUADRAlink Conversion Kit Camaro/Firebird P/N:
Detroit Speed, Inc. Rear QUADRAlink Conversion Kit 1982-92 Camaro/Firebird P/N: 041721 The Detroit Speed Inc. QUADRAlink Conversion Kit, eliminates the factory torque arm configuration. It features no-compromise
More informationLOADER MOUNTING KIT 5211 LOADER JOHN DEERE TRACTORS
ASSEMBLY MANUAL 2-6976 Keep with Operators Manual LOADER MOUNTING KIT 5211 LOADER JOHN DEERE TRACTORS MODEL 2WD FWA ROPS CAB JD 6110, 6120 X X X X JD 6210, 6220 X X X X JD 610, 620 X X X X JD 610, 620
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS FOR E-Z-GO MPT BALL CAGE (p/n 72685-G01) The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation
More informationOPERATOR ADAPTER A21ABA
OPERATOR ADAPTER A21ABA Installation Instructions for Allen Bradley Bulletin 1494F Disconnect Switches And Bulletin 1494D Circuit Breaker Operating Mechanisms (For parts list, see page 2) For floor mounted
More informationTrailer Hitch Platform Package Installation
Page 1 of 9 2014 Chevrolet Silverado 1500-2WD Sierra, Silverado VIN C/K Accessory Installation Manual Accessories Trailer Hitch Platform Package Installation Table 1: Light Duty Hitch Platform Kit Contents
More informationREVTEK SUSPENSION RECOMMENDS USING RED LOCTITE ON ALL FASTENERS UNLESS OTHERWISE NOTED. ALSO, HAVE THE FRONT END ALIGNMENT CHECKED AFTER INSTALLATION
2016 TOYOTA TACOMA 4WD & PRERUNNER INSTRUCTIONS 3 SUSPENSION LIFT KIT W/BLOCKS P/N 40014 WARNING!!!! PRODUCT SAFETY LABEL MUST BE INSTALLED INSIDE THE CAB OF THE VEHICLE IN PLAIN VIEW OF ALL OCCUPANTS!
More informationEngineered to Ride, Built to last
Congratulations on your selection to purchase an Arnott Air Suspension System. We at Arnott Air Suspension Systems are proud to offer a high quality product at the industries most competitive pricing.
More informationInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2766 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
More informationDODGE / RAM 1500 *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMENDED TOWING CAPACITY ***
6444 DODGE / RAM 500 6/8/207 OF 5 *** DO NOT EXCEED MANUFACTURER'S RECOMENDED TOWING CAPACITY *** ITEM QTY PART NUMBER 0 /2-3 x 2" 2 4 /2-3 x 3/4, GR8 3 4 CM-SP2 4 2 CM-SP6 5 4 HFN 23, GR8 6 2 CM-SP4 7
More informationINSTRUCTION BULLETIN
INSTRUCTION BULLETIN No. 328288 Machine: M20/T20/M30/ S30 Published: 05-2011 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in
More informationSTOP. 44" High Speed Sweeper. Operator's Manual. Model No Safety Assembly Operation Maintenance Parts
Operator's Manual STOP 44" High Speed Sweeper Model No. 486.029 DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 CAUTION: Before using this product, read this manual and
More informationInstallation Instructions
DODGE 20K Industry Standard Rail Custom Mounting Kit #2740 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationLifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Intermediate Pulley Shaft and Bearings
How To... Replace the Pulley Shaft and s Special Service Tools: Service Tool Kit Part Number: ToolKit 1. Remove the side covers. Refer to, How To Remove Pedals, Pedal Levers, and Side Shrouds. Main Drive
More informationGravely Dealers (US & CAN), RM s, DM s, Sales Partners, Tech Service, Customer Service
Date: 01//2012 No. DB02-G Dealer Bulletin Product Family: Gravely From: Distribution: Subject: Ariens Product Marketing Gravely Dealers (US & CAN), RM s, DM s, Sales Partners, Tech Service, Customer Service
More informationFord C4 and C6 Floor Mount Automatic Transmission Shifter Installation Instructions
Ford C4 and C6 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford C4 and C6 Mount
More informationPRODUCT USE INFORMATION
9RC61000 Jeep YJ Body Lift Thank you for choosing Rough Country for all your suspension needs. This body lift fits both manual and Automatic equipped vehicles!!! Refer to last page of this Instruction
More informationInstallation Instructions
DODGE 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2230 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note, in
More informationSafety First. Please remember to always use SAFE shop practices when performing all service procedures.
Safety First Please remember to always use SAFE shop practices when performing all service procedures. 2006 Update Manual January 2006 Country Clipper 2006 Update Manual Index Joystick Kill Switch Oil
More informationInstallation Guide. Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) Section 1.0: Mounting the M-Series Arm Parts Reference...
Installation Guide Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) The purpose of this guide is to describe installation of the MP90 M-Series Wall Mount Kit. Table of Contents Section 1.0: Mounting
More informationMOUNTING INSTRUCTIONS JOHN DEERE GATOR NON-ROPS CAB
MOUNTING INSTRUCTIONS JOHN DEERE GATOR NON-ROPS CAB FITS 4X2 & 6X4 GATORS A-11112, A-11224, A-11225, A-11226 MANUFACTURED BY: BOX 70 LITCHFIELD, MINNESOTA 55355-0070 (320) 693-3221 Fax: (320) 693-7252
More informationK Autoslide & K Autoslide
HJ26077, Rev 16 07/18 5th wheel hitch 6077 18K Autoslide & 6107 21K Autoslide US Pat. 7,506,886 US Pat. 7,753,392 CA Pat. 2,576,427 AS Pat. 2007200421 Important Information WARRANTY POLICY, OPERATOR MANUALS
More information05 12 TOYOTA TACOMA 2WD
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714 630 0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: PARTS LIST K756864 6" LIFT KIT 05 12 TOYOTA TACOMA 2WD QTY SPINDLE,
More informationE-Z-GO RXV Long Travel Lift Kit 2008 & Newer Gas Installation Instructions Part# 7495 U.S.PAT U N E J K E L B C M
E-Z-GO RXV Long Travel Lift Kit 2008 & Newer Gas Installation Instructions Part# 7495 U.S.PAT. 7581740 R S T O Q P U N E J K E D F G L B C M ITEM H A I QTY A. JAKES SUB-FRAME 1 B. TIE ROD EXTENSION 1 C.
More informationTrucks with a mass damper on the front diff, the damper will have to be removed.
922912000B *1291BAG6* 1291BAG6 Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More informationLIFT-506 BMF Lift Kit Club Car DS Gas & Electric Installation Instructions
LIFT-506 BMF Lift Kit Club Car DS Gas & Electric 2003.5-09 Installation Instructions Contents of LIFT-506 Club Car DS BMF Lift Kit: a (1 ea.) BMF Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1
More informationJD TRIPLE EGRESS TRIPLE EGRESS SECTION
JD 52-5525 TRIPLE EGRESS TRIPLE EGRESS SECTION 5525 EGRESS 5-1 ASSEMBLY - TRIPLE EGRESS, CAB TRIPLE EGRESS MOUNTING Park the tractor on a flat, hard, level surface. Lower both side decks down onto the
More informationRead and understand all instructions and warnings prior to installation of system and operation of vehicle.
491 W. Garfield Ave., Coldwater, MI 49036 Phone: 517-279-2135 Web/live chat: www.bds-suspension.com E-mail: tech@bds-suspension.com Part#:022410 Product: 4" Suspension System Application: 2002-2005 Dodge
More informationGLACIER PRO RANGER MID SIZE MOUNT KIT
GLACIER PRO RANGER MID SIZE MOUNT KIT P/N 2880261 APPLICATION FOR USE WITH THE GLACIER PRO MID SIZE PLOW SYSTEM (P/N 2880260) ON 2010 AND NEWER RANGER MID SIZE MODELS BEFORE YOU BEGIN Read these instructions
More informationSERVICE BULLETIN SB.DSL rev02
DSL 505 Rear Delt / Pec Fly Cable Repair Applies to DSL 505 Rear Delt / Pec Fly built prior to 5/16/2017 Issue/Symptoms On some machines using the 1/8 diameter lift cables, the cam cables may twist and
More informationSERVICE BULLETIN #
SERVICE BULLETIN # 910044 DATE: December 4, 2006 TO: Miller Pro Dealers & Service, Miller St. Nazianz FROM: OXBO International Corp. / NY Engineering / M. Leiston RE: 2006 Triple merger updates (S/N s
More informationInstruction Sheet Kit Number:
Instruction Sheet Kit Number: 7914400 POWERED DECK LIFT KIT WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand and follow all safety practices
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory FABRIC FRONT DOORS P/N 0SR90-HL4-211A (BLACK) P/N 0SR90-HL4-221A (CAMO) Application SXS1000M3/M3P/M5P/M5D Honda Dealer: Please give a copy of these instructions to your
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More information09-12 Dodge 4WD /4 Body Lift
92RC80000 09-12 Dodge 4WD 1500 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationCollector Drive for 60 Mower
FORM NO. -66 Collector Drive for 60 Mower Model No. 7965-990000 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the
More information7/18 HJ26077 Rev 16. US Pat. 7,506,886 US Pat. 7,753,392 CA Pat. 2,576,427 AS Pat PAGE 1
7/18 HJ26077 Rev 16 US Pat. 7,506,886 US Pat. 7,753,392 CA Pat. 2,576,427 AS Pat. 2007200421 PAGE 1 WARRANTY POLICY, OPERATOR MANUALS & REGISTRATION Go online to www.demco-products.com to review Demco
More informationMobtown Offroad Toyota Tacoma Bolt On Rock Slider Installation Instructions
Mobtown Offroad 2005+ Toyota Tacoma Bolt On Rock Slider Installation Instructions Tools Needed: 9/16 Box Wrench 9/16 Standard and Deep Well Socket, 3/8 Drive Ratchet, 3/8 Drive 3/4 Standard Socket 3/4
More informationVALVE AND PLUMBING KIT NEW HOLLAND 7310 LOADER NEW HOLLAND TRACTORS
ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT NEW HOLLAND 73 LOADER NEW HOLLAND TRACTORS MODEL 2WD FWA LESS CAB WITH CAB TT55 X X X TT75 X X X Valve and plumbing kit can be installed
More informationTO THE OWNER ASSEMBLY
TO THE OWNER This is an operational and general maintenance manual only and does not cover repair. All repair work must be performed by an authorized BOLENS DEALER or the factory warranty is void. Bolens
More informationINSTALLATION INSTRUCTIONS AND PARTS LIST MODEL , GRIP STEPS (BOARDS ONLY) UNIVERSAL APPLICATIONS
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL 415114, GRIP STEPS (BOARDS ONLY) UNIVERSAL APPLICATIONS 1. Read instructions completely and check to make sure that all required parts (listed on the service
More informationPN# PLT Toyota Tacoma/ Toyota Tundra/ Toyota 4- Runner/ Toyota Sequoia 2WD & 4WD Spacer Kit
PRO COMP SUSPENSION Suspension Systems that Work! PN# 1996-2004 Toyota Tacoma/ 1996-2006 Toyota Tundra/ 1996-2002 Toyota 4- Runner/ 2000-2006 Toyota Sequoia 2WD & 4WD Spacer Kit This document contains
More informationASSEMBLY MANUAL. Keep With Operator s Manual
ASSEMBLY MANUAL Keep With Operator s Manual 2-6347 VALVE AND PLUMBING KIT INSTRUCTIONS SMC 64Q LOADER KUBOTA TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB B2150DT & B2150HSD X X B8200DT & B8200HSD X X B9200DT
More informationPFadvantage JD 3300/4400/6600/7700; 4420
Ag Leader Technology Combine Installation JD 33//66/77; 2 Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number 3 3 6 6
More informationLIFT Standard A-Arm Lift Kit Club Car Precedent Installation Instructions
LIFT-563 6 Standard A-Arm Lift Kit Club Car Precedent Installation Instructions Contents of LIFT-563 Club Car Precedent Lift Kit: a (1 ea.) Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1 ea.)
More informationJEEP JK 3 1/4 COIL & SPACER KIT W/ PERFORMANCE 2.2. SHOCK ABSORBERS
92PERF693 JEEP JK 3 1/4 COIL & SPACER KIT W/ PERFORMANCE 2.2. SHOCK ABSORBERS Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install
More informationChrysler 727, 904, 518 Floor Mount Automatic Transmission Shifter Installation Instructions
Chrysler 727, 904, 518 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Release Button
More information72K850ZP PARTS MANUAL
7 2 K 8 5 0 Z P PARTS MANUAL 72 MID-CUT GAS ENGINE OPTION SECTION 72 MID-CUT DECK ASSEMBLY 72" Mid-Cut Deck Assembly # PART NO. QTY DESCRIPTION 1 582096 1 72" MC DECK WELDMENT 2 582098 1 72" DECK CHANNEL
More information2010 Current Ford Raptor Lower Control Arm Installation Instructions
PREPARATION 2010 Current Ford Raptor Lower Control Arm Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We
More informationFord AOD-4R70W-AODE Cable Operated Shifter Installation Instructions
Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable
More informationDODGE SuperRail Mounting Kit #0848
DODGE SuperRail Mounting Kit #0848 #1200 Super 5 th (16K) #0800 Super 5 th (20.5K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)
More informationFord F150/Raptor & F150 Lower Control Arm Installation Instructions
2009-2010 Ford F150/Raptor & 2015-2017 F150 Lower Control Arm Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency
More informationFORD SuperRail Mounting Kit #3361
FORD SuperRail Mounting Kit #3361 #4100 SuperGlide (16K) #4400 SuperGlide (20K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)
More informationK Autoslide. HJ26141, Rev 13 12/18
5th wheel hitch 6141 13K Autoslide HJ26141, Rev 13 12/18 INTRODUCTION WARRANTY POLICY, OPERATOR MANUALS, PARTS MANUALS & REGISTRATION Go online to www.demco-products.com to review Demco warranty policies,
More informationInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2738 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
More informationDetroit Speed, Inc. QUADRA Link Rear Suspension Nova P/N:
Detroit Speed, Inc. QUADRA Link Rear Suspension 1968-1974 Nova P/N: 041704 The Detroit Speed Inc., QUADRA Link rear suspension system is a great way to upgrade from an original leaf spring rear suspension.
More informationWINDSHIELD WIPER KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS NOTE. Instr Rev 02 06/15 Page 1 of 7
WINDSHIELD WIPER KIT P/N 2879968 APPLICATION RANGER 570, RANGER ETX AND RANGER EV Polaris does not recommend use of this kit with Tip-Out Windshield PN 2880442. BEFORE YOU BEGIN Read these instructions
More informationJD TRIPLE EGRESS TRIPLE EGRESS SECTION
JD 72-7420 TRIPLE EGRESS TRIPLE EGRESS SECTION Assembly Section 5-1 ASSEMBLY - TRIPLE EGRESS, CAB TRIPLE EGRESS MOUNTING Park the tractor on a flat, hard, level surface. Lower both side decks down onto
More informationLankota, INC. LAN AR100. Adapts Older Model Row Crop Heads To Newer 50 & 60 Series Combines. Installation Instructions
Lankota, INC. LAN AR100 Adapts Older Model Row Crop Heads To Newer 50 & 60 Series Combines Installation Instructions Kit LAN-AR100 Lankota is the trademark of Lankota, Inc. 1 LAN AR100 Parts break down
More informationHP10207 KIT. Ram WD*
HP10207 KIT Ram 1500 4WD* (For 2WD call customer service 800.663.0096 for assistance) * See application guide for proper fitment. Use the most advanced air springs on the market to eliminate your vehicle
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FX4 ELITE REAR DISC CONVERSION KITS WITH INTERNAL PARKING BRAKE A110-14, A111-25, A111-29 for FORD 8" & 9" REAR ENDS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More information2 Strut Spacer / Preload Lift. Ford Ranger 4wd Part#:
Part#: 013203 2 Strut Spacer / Preload Lift Ford Ranger 4wd 2019 Rev. 022119 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web: www.bds-suspension.com. E-mail: tech-bds@ridefox.com Read
More informationRear bumper cannot be used for towing after installation of the rear bumper relocation brackets.
921RC7030 GM 88-98 4WD 1500 P/U 3 Body Lift Thank you for choosing Rough Country for all your suspension needs. *RC703BAG2* RC703BAG2 Rough Country recommends a certified technician install this kit. Attempts
More information