Quantity Model Length (in.) Width (in.) Height (in.) Volume (CFM) SP (in. wg) 1 Air Curtain Supply (ASP)

Size: px

Start display at page:

Download "Quantity Model Length (in.) Width (in.) Height (in.) Volume (CFM) SP (in. wg) 1 Air Curtain Supply (ASP)"

Franklin Eaton
5 years ago
Views:

1 Mark: ASP 1 Model: ASP S ASP Air Curtain Supply (ASP) Quantity Model Length (in.) Width (in.) Height (in.) Volume (CFM) SP (in. wg) 1 Air Curtain Supply (ASP) Supply Collar Data: Collar # Collar Size (LxW) in. or Diameter (in.) Pos. Off Left Pos. Off Front Velocity (fpm) Mounting 1 22 x Factory Mounted Supply Collar(s) Selected Options & Accessories: 430 Stainless Steel MBD(s) in Plenum CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 1 of 16

2 Mark: ASP 1 Model: ASP S MARK: ASP PERFORATED AIR CURTAIN CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 2 of 16

3 Mark: ASP 2 Model: ASP S ASP Air Curtain Supply (ASP) Quantity Model Length (in.) Width (in.) Height (in.) Volume (CFM) SP (in. wg) 1 Air Curtain Supply (ASP) Supply Collar Data: Collar # Collar Size (LxW) in. or Diameter (in.) Pos. Off Left Pos. Off Front Velocity (fpm) Mounting 1 18 x Factory Mounted Supply Collar(s) 2 18 x Factory Mounted Supply Collar(s) Selected Options & Accessories: 430 Stainless Steel MBD(s) in Plenum CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 3 of 16

4 Mark: ASP 2 Model: ASP S MARK: ASP PERFORATED AIR CURTAIN CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 4 of 16

Model: DG-109-H10 DG-109-H10 Unit Performance Design Conditions Elevation (ft) Summer DB ( F) WB ( F) Winter ( F) Supply (CFM) Outdoor Air (CFM) 692 91.2 77.2-0.

5 Model: DG-109-H10 DG-109-H10 Unit Performance Design Conditions Elevation (ft) Summer DB ( F) WB ( F) Winter ( F) Supply (CFM) Outdoor Air (CFM) ,000 2,000 Unit Specifications Weight (lb) Cooling Type Heating Type Unit Installation Unit ETL Listing 482 (+/- 5%) None Direct Gas-Fired Outdoor/Indoor ANSI Z83.4 / CSA 3.7 Configuration Unit Orientation Unit Configuration Outdoor Air Intake Return Air Intake Supply Air Discharge Horizontal Constant Volume 100% OA End - Bottom Heating Specifications Gas Pressure Capacity (MBH) Performance Temperature Type Gas Type Min Max Input Output Rise ( F) EAT ( F) LAT ( F) (in. wg) (Psi) Direct Gas Natural Air Performance Total Fan External SP Total SP Operating Type Volume RPM (in. wg) (in. wg) Power (hp) (CFM) Qty Type Size (in.) Drive-Type Supply 2, Forward Curve 9 Belt-Drive Motor Specifications Motor Qty Size (hp) Enclosure Efficiency RPM Supply Fan Motor 1 1-1/2 ODP NEMA Premium 1725 Electrical Specifications Power Supply Rating (V/C/P) MCA (A) MOP (A) Unit 208/60/ CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 5 of 16

6 Model: DG-109-H10 CONSTRUCTION FEATURES AND ACCESSORIES Unit Unit Installation - Indoor or Outdoor Unit Construction - Single Wall Wall Insulation - 1in. fiberglass - Heat source on Base Insulation - 1in. fiberglass - entire unit base pan Corrosion Resistant Fasteners Access and Connections - Right side when facing intake Service Access - Removable lift off panels Unit Finish - G90 Galvanized Finish Color Supply Fan - Belt-drive, forward-curved Supply Fan and Motor Vibration isolation - Neoprene Controls Unit Controls - Terminal strip Remote Panel Temperature Control - Discharge control Supply Fan VFD Supply Fan Control Melink/Vari-Flow wiring package Recirculation Control Unoccupied Mode (Night Setback) Control Accessories Heating Inlet Air Sensor Cooling Inlet Air Sensor Dirty Filter Switch Fire Stat Type III (Ships loose) 120V/24V Smoke Detector (Ships loose) Inlet Damper End Switch External Cooling Lockout Relay Freeze Protection (Supply Air Low Limit) Auxiliary Supply Starter Contacts Auxiliary Exhaust Starter Contacts Airflow Proving Monitoring Contact Std Std Std Accessories Factory Installed, Lockable, NEMA 3R Disconnect Weatherhood - Aluminum Mesh filtered Supply Air Filters Outdoor Air Inlet Damper Supply Air Outlet Damper Diffuser Roof Curb - GPI Combination Curb Spare Belts Spare Filters Motor with Shaft Grounding Service Outlet Gas Heating Accessories Pilot Ignition Flame Sensing - Flame rod Flame Safeguard Display Agency Approval - ETL and IRI FM Approved Minnesota Code Requirements High Gas Pressure Switch Low Gas Pressure Switch Visual Indication Valves External Gas Pressure Regulator (Ships loose) Warranty Options Unit Warranty - 1 Year 5 Year Burner Warranty 10 Year Burner Warranty Std Std Std Standard Option Std Not Included Included CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 6 of 16

7 Model: DG-109-H10 Fan Charts And Performance Supply Fan Performance Motor Fan Total Volume External SP Total SP Operating RPM (CFM) (in. wg) (in. wg) Power (hp) Size Qty Qty Type Drive-Type (hp) 2, /2 1 Forward Curve Belt Pressure Drop (in. wg) Weatherhood Filter Damper Cooling Heating External Total Sound Performance in Accordance with AMCA Sound Power by Octave Band Lwa dba Sones Supply Fan CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 7 of 16

8 Model: DG-109-H10 Heating Specifications Heating Performance Gas Pressure Capacity (MBH) Performance Temperature Type Gas Type Min Max Input Output Rise ( F) EAT ( F) LAT ( F) (in. wg) (Psi) Direct Gas Natural Gas Train Details Redundant Electronic Main Modulating Valves Valve Pilot Valve Internal Regulator Visual Indication Valve Proof of Closure Valve Hydraulic Gas Pressure Main Valve(s) Switch(es) External Regulator Std Std Std Std Additional Heating Information Agency Approvals ETL and IRI Temperature Control Ignition Control Flame Safeguard Display Minnesota Flame Sensing CO2 Sensor FM Approved Code Std - - Discharge Flame Rod Pilot - - Unit Details 92% thermal efficiency Cast aluminum burner manifold with stainless steel mixing plates Electronic modulation burner control 10 second pre-purge sequence Low fire start ELECTRICAL CONNECTION Gas Connections /4" NPT GAS CONNECTION CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 8 of 16

9 Model: DG-109-H ELEVATION VIEW *Standard configuration for unit access is on the right-hand side, when looking into the unit intake in the direction of airflow. *Note: Order of unit sections is from intake of unit to discharge of unit. *Sections included on this unit: Weatherhood Section, Heating Section *Insulation: Duct Liner, from Burner Section through end of unit. INTAKE BURNER SUPPLY DUCT ACCESS SIDE- CONTROL CENTER PLAN VIEW * Standard configuration for unit access is on the right-hand side, when looking into the unit intake in the direction of airflow. CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 9 of 16

10 Model: DG-109-H END VIEW NOTE: Roof Opening Requirements: Minimum Roof Opening: The minimum roof opening size is the illustrated duct diameter plus 0.25 in. on all sides. For example: If the duct size is 14 x 14 in. square, the minimum roof opening size is 14.5 x 14.5 in. square. Maximum Roof Opening: There must be a minimum perimeter of 1.75 in. between the roof opening and the roof curb. For example: If the roof curb is 75 x 30 in. square, the maximum roof opening is 71.5 x 26.5 in. inches square CURB LENGTH ACTUAL Supply Duct CURB WIDTH ACTUAL 5.47 NOTE: The weatherhood and filter sections of the make-up air unit extend beyond the curb. This is by design, to prevent water infiltration. MUA Unit supports are shipped loose with unit. FOOTPRINT VIEW CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 10 of 16

11 Model: DG-109-H10 UNIT BASE INSULATION CURB INSIDE OF RAILS CURB VIEW Notes: All dimensions shown are in in.'s. Curb Dimenision: Length = 74.5 in. Width = 24.5 in. Height = 20 in. Recommended Minimum Combustible Clearances Floor Top Sides Ends Insulated/Units 0 in. 0 in. 0 in. 0 in. Non-Insulated/Units 0 in. 6 in. 6 in. 6 in. Clearance to combustibles is defined as the minimum distance required between the heating source and the adjacent combustible surfaces to ensure the adjacent surface's temperature does not exceed 90 F above the ambient temperature. Housing 32 and less Recommended Minimum Service Clearances 42 in. on the controls side of the unit Housing 35 and higher 48 in. on the controls side of the unit To ensure ample space for component removal (evaporative cooling media, coils, filters, etc.), service clearances should be 6 in. wider than the width of the module itself. CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 11 of 16

12 Model: DG-109-H10 MAIN POWER TO UNIT 208V GROUND L1 L2 L3 DS1 T1 T2 T3 ST1 O.L. L1 T1 L2 T2 L3 T3 M1 SUPPLY FAN MOTOR A C C U R E ENGINEERED RESTAURANT SYSTEMS Wiring Diagram Code: AD61N401A010N10NM19 CAUTION UNIT SHALL BE GROUNDED IN ACCORDANCE WITH N.E.C. POWER MUST BE OFF WHILE SERVICING. NOTES USE COPPER CONDUCTORS ONLY 60 C FOR TERMINALS RATED LESS THAN 100 AMPS. 75 C FOR TERMINALS RATED 100 AMPS OR MORE. FIELD CONTROL WIRING RESISTANCE SHOULD NOT ECEED 0.75 OHM. FIELD WIRED TR5 FACTORY SUPPLIED AND WIRED 40VA 24V WIRE COLOR CODE BLUE R S2 FSC G PINK ST1 O.L TR1 24V VA C RED BLACK D1 INLET DAMPER 2CBL-ID 2CBL-ID PINK PINK 4 RF SUPPLY FAN RELAY A2 A1 WHITE BK BLACK BL BLUE BR BROWN GY GRAY LT BL LIGHT BLUE O ORANGE PK PINK PR PURPLE R RED W WHITE Y YELLOW LEGEND AMP AMPLIFIER D1 INLET DAMPER DS1 MAIN DISCONNECT SWITCH FSC FIRE SYSTEM CONTACT FSG FLAME SAFE GUARD HLC HIGH LIMIT CONTROL M# MOTOR MOD MODULATING VALVE OL# MOTOR OVERLOAD PS2 AIR PROVING SWITCH RF SUPPLY FAN RELAY RH HEAT RELAY S2 FAN SWITCH S4 HEAT AND COOL SWITCH SG SPARK GENERATOR ST# MOTOR STARTER TR# TRANSFORMER TS2 DISCHARGE AIR SENSOR TS4 INLET AIR SENSOR - HEAT V1 PILOT VALVE V2 MAIN VALVE RF BROWN ST1 A2 A1 SUPPLY FAN S4 W1 RED 13 ST1 14 RED R TS4 B RED A2 RH A1 POST HEAT RH HLC1 RED RED R R PS2 PS2 RED BLACK C NO NC C RED 27 O 21 DIRECT GAS CONTROL SENSOR SPARK SENSE SPARK TH/24V FSG MV PV GND (BURNER) GND (24V) WHITE 29 LT BLUE V1 WHITE BLUE ORANGE WHITE 37 V2 TR6 INT 10 SEC AMP 7 DISCHARGE STAT. TEMP RANGE F 39 BLUE 30 VA 24 VAC YELLOW BLACK WHITE BLUE BLUE TS2 1 2 MOD Wiring Template: M19 DOC NUMBER: ---- REV: ---- Manufacturer reserves the right to change, modify, or improve this product at anytime CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 12 of 16

13 Roof Curb - GPI CONSTRUCTION FEATURES Welded aluminum (0.064 in.) or galvanized steel (18 ga.) Straight sided 2 in. mounting flange 1 in., 3 lb. density insulation Wood nailer Dimension Description Value (in.) A Length 74.5 B Width 24.5 C Height 20 * All dimensions are actual GPI Curb Weight: 64 lb Printed Date: 11/02/2018 Model: DG-109-H10 ADDITIONAL NOTES The Roof Opening Dimension may NOT match the Structural Roof Support Dimension. Curbs with length > will ship knocked-down Curbs with length > may ship knocked-down, dependent on manufacturing location CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 13 of 16

14 Model: DG-109-H10 Corner Weights 133 lb 96 lb 146 lb 106 lb Note: Estimated corner weights are shown looking down on unit and airflow from left to right. Weights are applied at the base of the unit. Images not drawn to scale. CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 14 of 16

15 Model: DG-109-H10 Unit Controls The unit shall be provided from the factory with: SEQUENCE OF OPERATIONS 24VAC Transformer Terminal Strip Supply fan motor starter (contactor and overload) Factory mounted and wired outdoor air inlet damper with actuator Field Provided Control Requirements The following field provided control signals must be provided for proper operation of the unit (Reference the unit wiring diagram for additional information): Supply fan enable Contact closure between R and G (24VAC) Heating enable Contact closure between R and W1 (24VAC) Unit Start-Up Sequence Supply Fan Enable Is Received Outdoor air inlet damper actuator is energized Supply Fan Is Enabled Supply Fan Sequence The supply fan is configured for constant volume operation. The fan speed is set to the design fan RPM at the factory through the use of belts and sheaves. Adjustment or replacement of belts/sheaves is necessary to balance the supply airflow. The supply fan speed is not to be modulated. Heating Control A heating enable signal must be present and the supply fan must enabled before the unit will enable heating. Heating Inlet Air Sensor (Heating Lockout) The heating will be locked out when the outside air temperature is above the heating inlet air sensor set point (typical 65 F, adj.) Direct Gas Fired Heating (Discharge Control) The gas control amplifier located in the unit shall modulate the heating to maintain a supply temperature set point (55 F-90 F, adj.). The set point is adjusted in the unit control center. CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 15 of 16

16 Model: DG-109-H10 Warranty Information Limited Warranty - Unit Accurex warrants this equipment to be free from defects in material and workmanship for a period of 1 year(s) from the purchase date. Any component which proves defective during the warranty period will be repaired, or replaced, at Accurex's sole option when returned to our factory, transportation prepaid. The warranty does not include labor costs associated with troubleshooting, removal, or installation. Accurex will not be liable for any consequential, punitive, or incidental damages resulting from use, repair, or operation of any Accurex product. This warranty is exclusive, and is in lieu of all other warranties, whether written, oral or implied, including the warranty of merchantability and the warranty of fitness for a particular purpose. CAPS C:\Users\holbrook\Syncplicity Folders\Acx-OH\2018 Jobs\skyline Chili\Skyline Chilli.acxj Page 16 of 16

Direct Gas-Fired Heating

Direct Gas-Fired Heating Model DG 800 to 15,000 cfm Up to 1,600,000 BTU/hr Optional Evaporative Cooling January 2005 PRODUCT FEATURES Model DG Direct Gas-Fired Make-Up Air Unit The Greenheck model DG is