INSTALLATION / OPERATION MANUAL CASE-IH 3200 & 3400 NEW HOLLAND 996

Transcription

1 w w w. S t a l k S t r y k e r. c o m INSTALLATION / OPERATION MANUAL CASE-IH 3200 & 3400 NEW HOLLAND 996

2 INTRODUCTION IMPORTANT: Read through this instruction manual thoroughly and familiarize yourself with the machine before performing any procedures. Average installation time: TABLE OF CONTENTS 2

3 FRAME KIT MAIN COMPONENTS & HARDWARE LIST COMPONENT FRAME KIT A-STR3420 A-STR3440 A-STR3460 A-STR3406 A-STR3408 A-STR3412 A-STR100B A-STR A-STR3T A-STR52T A-STR53T A-HK A-HK A-HK

4 HARDWARE KIT COMPONENTS KITS COMPONENTS A-HK444 (2) 5/8 x 2.5 U-Bolts (8) 5/8 Serrated Nuts (2) 5/8 x 4 U-Bolts A-HK101 (1) Hitch Pin (2) 5/8 x 2.5 U-Bolts (1) Lynch Pin (4) 5/8 Serrated Nuts A-HK531 (2) 1/2 x 3.5 NC Bolts (2) 1/2 Serrated Nuts 4

5 Recognize Safety Information Understand Signal Words DANGER WARNING CAUTION DANGER WARNING CAUTION Follow Safety Instructions Park Machine Safely & Prepare Machine for Service Feeder House Safety Stop Identi- 5

6 INSTALLATION PROCEDURES A-STR3420 A-STR3420C 2-Row Models A-STR3440 A-STR3440C 4-Row Models A-STR3460 A-STR3460C 6-Row Models 2-Row 4-Row 6-Row A) Attach center Main Brackets A-STR434 to header using Hardware Kit A-HK444. 6

7 B) Attach outer Main Bracket A-STR434 to header using Hardware Kit A-HK444. Note: 7

8 C) Assemble toolbars A-STR53T and A-STR52T together using Hardware Kit A-HK & 4 row 8

9 6 row 6 row D) Attach toolbars A-STR53T and A-STR52T assembly to the main brackets using Hardware Kit A-HK444. 9

10 E) Attach Stalk Stryker Mounting Brackets A-STR100B to the toolbar using Hardware Kit A-HK

11 F) Attach Stalk Stryker shoes A-STR101 to the A-STR100B bracket. Adjustment of down pressure is necessary for the correct operation of the Stalk Stryker See page 22 for Down Pressure Adjustment instructions. These instructions cover installation on one side of the header. Repeat to complete Stalk Stryker installation on the opposite side. 11

12 INSTALLATION PROCEDURES A-STR3406 A-STR3406C 6-Row Models A-STR3408 A-STR3408C 8-Row Models A) Attach center Main Bracket A-STR434 to header using Hardware Kit A-HK

13 B) Attach outer Main Brackets A-STR434 to header using Hardware Kit A-HK444. Note: 13

14 C) Assemble toolbars A-STR53T and A-STR52T together using Hardware Kit A-HK

15 D) Attach toolbars A-STR53T and A-STR52T assembly to the main brackets using Hardware Kit A-HK444. E) Attach Stalk Stryker Mounting Brackets A-STR100B to the toolbar using Hardware Kit A-HK

16 F) Attach Stalk Stryker shoes A-STR101 to the A-STR100B bracket. Adjustment of down pressure is necessary for the correct operation of the Stalk Stryker See page 22 for Down Pressure Adjustment instructions. These instructions cover installation on one side of the header. Repeat to complete Stalk Stryker installation on the opposite side. 16

17 INSTALLATION PROCEDURES A-STR3412 A-STR3412C 12-Row Models A) Attach center Main Bracket A-STR434 to header using Hardware Kit A-HK

18 B) Attach middle and outside Main Brackets A-STR434 to header using Hardware Kit A-HK444. Note: 18

19 header 19

20 C) Assemble toolbars A-STR53T, A-STR52T, and A-STR3T together using Hardware Kit A-HK531. D) Attach toolbars A-STR53T and A-STR52T assembly to the main brackets using Hardware Kit A-HK

21 E) Attach Stalk Stryker Mounting Brackets A-STR100B to the toolbar using Hardware Kit A-HK101. F) Attach Stalk Stryker shoes A-STR101 to the A-STR100B bracket. Adjustment of down pressure is necessary for the correct operation of the Stalk Stryker See page 22 for Down Pressure Adjustment instructions. These instructions cover installation on one side of the header. Repeat to complete Stalk Stryker installation on the opposite side. 21

22 Adjustment of the down pressure is necessary for the correct operation of the Stalk Stryker A) The correct adjustment can be achieved by changing the location of the pin into one of the 8 angle/height adjustment position hole locations. IMPORTANT: Be certain to adjust the Stalk Stryker to acheive the correct down pressure. mature wear or failure and will result in loss of warranty coverage for the Stalk Stryker. 22

23 TRANSPORT & STORAGE TRANSPORT SAFETY CAUTION: Stalk Stryker shoes must be removed from the operational position for transport on header carts. A) STORAGE OPTION A-STR290 storage bracket mounting and usage 23

24 w w w. S t a l k S t r y k e r. c o m CT722 July