SYSCO RDC SOUTH ALACHUA, FLORIDA

Size: px

Start display at page:

Download "SYSCO RDC SOUTH ALACHUA, FLORIDA"

William Chandler
5 years ago
Views:

1 SYSCO RDC SOUTH ALACHUA, FLORIDA July, 2018 Infrared Inspection Report Sysco RDC South NW 173rd Street Alachua, Florida, Company Contact: Natha Hall Project: CHARTER OAK DRIVE, LITTLE ROCK, AR PHONE: & FA:

2 ORDER OF REPORT CONTENTS 1: Data To Facilitate Understanding & Utilizing Scan Report 2: Scan Results Overview & Action Taken Form 3: Identified Faulting Conditions, Information & Photographs 4: List Of Facility Equipment Identified By The Customer Representative & Notations Of Faulting Conditions Found DISCLAIMER This report and the recommendations contained in it are based upon conditions and practices observed and information made available to United Spectrographics personnel. This report does not purport to list all hazards or faulty conditions. It is not intended to indicate that other hazards or faulty conditions do not exist. Severity ratings in the report are based on the criteria shown in this report and are intended as guidelines only. No responsibility is assumed for the control of the facility s condition, maintenance practices or correction of conditions indicated herein. By issuing this report, neither United Spectrographics nor any of its employees makes any warranty, expressed or implied, concerning the contents of this report. Furthermore, neither United Spectrographics nor any of its employees shall be liable in any manner (other than liability that may be expressed in any policy of insurance that may be issued by United Spectrographics) for personal injury or property damage or loss of any kind arising from or connected with this inspection or failure to inspect.

3 Utilizing Report Contents Included in this report are Photographs and Thermographs of problem areas found during our recent Infrared Inspection of your facility. Each problem area picture is accompanied by: Date Location Information Temperature Calculations Color-coded Temperature Intensity and/or Condition Significance Data A Brief Comment Relating The Item In The Photograph To Its Corresponding Thermograph Suggested Corrective Recommendations. In most cases, problems (faults) found will be listed according to the date and order that they were located, rather then by significance or priority, as we feel that you and/or your personnel can best judge this, keeping in mind circuit importance and thermograph intensity. Thermal intensity is indicated by use of a color-coded data inserts that locate a fault s position on the standard electrical failure curve. The color of the insert represents the temperature range of the hottest item, or a portion of the item's circuitry, pointed out in the thermograph. The temperature ranges which the colored inserts represent are grouped as follows: INSERT Red Orange Yellow Green Temperature Range 70ºC/126ºF and higher above Ambient Operating Temp. 40ºC/72ºF to 69ºC/124ºF above Ambient Operating Temp. 25ºC/45ºF to 39ºC/70ºF above Ambient Operating Temp. *10ºC/18ºF to 24ºC/43ºF above Ambient Operating Temp. ( * See page 4)

Determining Cost Effective Responses Electrical equipment failures generally follow a standard mechanical/electrical failure curve. Dividing the failure curve into temp.

4 Determining Cost Effective Responses Electrical equipment failures generally follow a standard mechanical/electrical failure curve. Dividing the failure curve into temp. ranges and locating a problems position on the curve allows us to indicate the probable time to its failure. Knowing a problems probable time to failure allows you to make a cost effective response to the problem areas that we locate. Below is a depiction of the electrical fault failure curve with the thermal intensity ranges and the colors that we assign to faults detailed in our reports. STANDARD ELECTRICAL FAULT FAILURE CURVE (Does Not Include Area In Blue) MINOR INTERMEDIATE SERIOUS CRITICAL DEVICE TEMP IS AMBIENT, BUT DEVICE IS EITHER FAULTY OR UNSAFE. 10ºC * 18ºF 25ºC 45ºF 40 C 72ºF 70 C 126ºF AMBIENT TEMP YEARS MONTHS MONTHS TO WEEKS WEEKS TO NOW FAULTY EQUIP Built In Trend Monitoring When yearly scans are accomplished, report results allow you to trend monitor your electrical equipment without having to cross reference previous report findings. If a previous years problem is not repaired it will show up again in the current scan report and its current intensity range indicates a current effective response.

5 Defining Total Temperature and Ambient Operating Temperature And Explanation For Their Use Total Temperature: Total Temperature = Ambient Operating Temperature + Fault temperature Allows you, the customer, to evaluate possible damage to equipment. Leads fail between 90ºC/194ºF and 110ºC/230º Phenolic fails around 200ºC/392ºF Transformers and Motor Insulation failure temperature depends on insulation class rating. Contacts start to fail around 130ºC/266ºF Ambient Operating Temperature (AOT*) for Infrared Scanning Purposes: Temperature within a device container (Box or Cabinet) that is not directly affected by faulting component = Normal Equipment Operating Temperature Contained By Box or Cabinet. If there is no container (Example: Device mounted to a wall) it is the temperature adjacent to the device not affected by the fault. Allows you, the customer, to determine if device will operate at intended amperage. Most switchgear is rated to operate at approximately 40ºC/104ºF (Industrial) to 50ºC/122ºF (Marine) If AOT is enough above normal rated temperature, either of the following conditions can cause an unanticipated trip. 1. An intermittent high load. 2. A minor (Green) or intermediate (Yellow) fault. Report pages with photographs: PH stands for Visible Light Photograph TH stands for Infrared Light Thermograph *AOT stands for Ambient Operating Temperature Both black & white and color infrared thermographs are presented to better depict the fault condition.

6 In addition to the corrective response time frame suggested below and the failure curve located on the previous page, you may want to consider using the military standard responses presented below. Military Standard For Evaluating Faults Located In Electrical Equipment Utilizing Temperature Data Obtained With Infrared Imaging Equipment: Temperatures rise above Ambient Operating Temperature: *10ºC/18ºF to 24ºC/43ºF component failure unlikely, but corrective measures required at next scheduled routine maintenance period or as scheduling permits. (Green Label) 25ºC/45ºF to 39ºC/70ºF component failure probable, unless corrected. (Yellow Label) 40ºC/72ºF to 69ºC/124ºF component failure almost certain, unless corrected. (Orange Label) 70ºC/126ºF and above component failure imminent. Immediately inform the person responsible for continued operation of equipment. (Red Label) Note: United Spectrographics uses a Blue Label to indicate faults that require attention due to either ambient temperature (Ex: Phase Not Operating), faulty equipment elements or unsafe conditions. * Note: Temperature conditions below 10ºC/18ºF rise above AOT are not considered significant enough to record and are usually not included in the reports unless the fault temperature is being affected by a cooling medium such as oil or wind. Fault Correction Recommendation When Our Source Assessment Is Inaccurate: When a fault is indicated in a connection or component and examination by your electrician does not turn up a loose connection or faulty component where we have indicated, a fault does exist. The electrician should continue to investigate the next connection or component to be found in the direction that the heat is coming from until a source is located. Example: If a molded case breaker line side lead connection lug is indicated as a fault source and is found to be secure, but not frozen in place, look for a loose connection or sign of over temp. in the lead holder lug.

7 SCAN RESULTS OVERVIEW PROMPT ATTENTION ITEMS: Because of: 1. The intensity or heat level indicated at the time of the scan. 2. Deterioration caused by excessive temperature not present at the time of the scan. 3. Physical condition irregularities observed at the time of the scan. We recommend that the following faults be given prompt attention: Faults: #2 Items With Asterisks Have High Total or Ambient Operating Temperatures. United Spectrographics July, 2018

8 SUMMARY OF FINDINGS FAULTS BY CATEGORY NUMBER OF FAULTS FAULT NO./ITEM NO. MINOR 0 0 INTERMEDIATE 1 1/203 SERIOUS 1 2/224 CRITICAL 0 0 SERIOUS 0 0 Number of items located at facility: 234 Number of faults: 2

9 ACTION TAKEN Sysco RDC South Alachua, Florida July, 2018 Fault # Item # Category Repaired Monitor Date Name Intermediate Serious

PROJECT: 05110818 CUST REP: SCAN REP: Mark Trey Dent DATE: July 11th, 2018 LOCATION:

TH # 1 > COMMENTS Abnormal heat is being generated in fuse block component.

10 PROJECT: CUST REP: SCAN REP: Mark Trey Dent DATE: July 11th, 2018 LOCATION: Roof Office Area Box Labeled: RTU-A2-S Fuse Disconnect PH # 1 > ITEM: SOURCE: TEMP: Bø Fuse Block Load side fuse clip Temp. of fuse clip is: 73ºC / 163ºF Total Temp - 37ºC / 99ºF AOT = 36ºC / 64ºF above AOT. TH # 1 > COMMENTS Abnormal heat is being generated in fuse block component. See yellow arrows in PH#1 and TH#1. Loose and/or corroded contact area. Clean, inspect and re-secure. TH # 1 > TEMPERATURE ABOVE AOT 36 C / 64 F

PROJECT: 05110818 CUST REP: SCAN REP: Mark Trey Dent DATE: July 11th, 2018 LOCATION: Roof-Warehouse Area Penthouse #5 Box Labeled: AHU-18

of connection and lug is: 31ºC / 88ºF Total Temp. -(12ºC) / 10ºF AOT = 43ºC / 78ºF above AOT.

11 PROJECT: CUST REP: SCAN REP: Mark Trey Dent DATE: July 11th, 2018 LOCATION: Roof-Warehouse Area Penthouse #5 Box Labeled: AHU-18 Combination Starter < PH # 2 ITEM: SOURCE: TEMP: Cø of Disconnect Load side lead connection lug Temp. of connection and lug is: 31ºC / 88ºF Total Temp. -(12ºC) / 10ºF AOT = 43ºC / 78ºF above AOT. < TH # 2 < TH # 2 COMMENTS Abnormal heat is being generated in disconnect connection. See orange arrows in PH#2 and TH#2. Loose and/or corroded contact area. Clean, inspect and re-secure serviceable components. TEMPERATURE ABOVE AOT 43 C / 78 F

12 AREA/EQUIPMENT LIST Following is a list of the electrical equipment located at the Sysco RDC South, Alachua, Florida, facility and data relating to its operating condition at the time the scan was performed. NOTE: Items noted as visually inspected were not operational or show no visible load at the time of the inspection. No. Equipment Operating Visually Inspected MAIN BUILDING Fault # MAIN ELECTRICAL ROOM 1 Switchboard MDP2 Section 1 Terminals 2 Switchboard MDP2 Section 2 480/277 Volt Distribution Panel 3 Switchboard MDP1 Section 1 Terminals 4 Switchboard MDP1 Section 2 480/277 Volt Distribution Panel 5 Switchboard MSBE-1 / MSBE-2 Section 1 Terminals 6 Switchboard MSBE-1 / MSBE-2 Section 2 480/277 Volt Distribution Panel 7 Switchboard MSBE-1 / MSBE-2 Section 3 NATS-2 Circuit Breaker 8 Switchboard MSBE-1 / MSBE-2 Section 4 ATS-2 Circuit Breaker 9 Switchboard MSBE-1 / MSBE-2 Section 5 Terminals 10 Switchboard MSBE-1 / MSBE-2 Section 6 Tie Breaker 11 Switchboard MSBE-1 / MSBE-2 Section 7 Terminals 12 Switchboard MSBE-1 / MSBE-2 Section 8 ATS-1 Circuit Breaker 13 Switchboard MSBE-1 / MSBE-2 Section 9 NATS-1 Circuit Breaker 14 Switchboard MSBE-1 / MSBE-2 Section /277 Volt Distribution Panel 15 Switchboard MSBE-1 / MSBE-2 Section 11 Terminals 16 ATS-1 17 ATS-2

13 No. Equipment Operating Visually Inspected 18 NATS-1 Fault # 19 NATS-2 20 ATS-3 21 ATS-4 22 Switchboard MSB-1 Section 1 Main Breaker 23 Switchboard MSB-1 Section 2 480/277 Volt Distribution Panel 24 Switchboard MSB-1 Section 3 ATS-1 25 Switchboard MSB-1 Section 4 NATS-1 26 Switchboard MSB-2 Section 1 Main Breaker 27 Switchboard MSB-2 Section 2 480/277 Volt Distribution Panel 28 Switchboard MSB-2 Section 3 ATS-2 29 Switchboard MSB-2 Section 4 NATS-2 VFD ROOM 30 Power Distribution Panel #2 31 VFD 01 AU VFD 02 AU VFD 03 AU VFD 04 AU VFD 05 AU VFD 06 AU22-23 Cond EC1 Fan VFD 07 Cond EC1 Fan Refrigeration Section 1 Control Panel 39 Refrigeration Section 2 I/O Panel 40 Refrigeration Section 3 Distribution Panel 41 Refrigeration Section 4 Starter Panel COMPRESSOR ELECTRICAL ROOM 42 PPB-1 480/277 Volt Distribution Panel 43 PPB-2 480/277 Volt Distribution Panel

14 No. Equipment Operating Visually Inspected 44 LP1E 480/277 Volt Distribution Panel 45 LPA 480/277 Volt Distribution Panel 46 RP /120 Volt Distribution Panel 47 RP /120 Volt Distribution Panel 48 FMR TR1 45 KVA Siemens 3ø Transformer 49 LP /277 Volt Distribution Panel 50 LP /277 Volt Distribution Panel 51 Switchboard MDP3 Section 1 Terminals 52 Switchboard MDP3 Section 2 480/277 Volt Distribution Panel 53 Switchboard MDP4 Section 1 Terminals 54 Switchboard MDP4 Section 2 480/277 Volt Distribution Panel AMMONIA COMPRESSOR ROOM 55 C-1 Compressor Control Cabinet 56 C-2 Compressor Control Cabinet 57 C-3 Compressor Control Cabinet 58 C-4 Compressor Control Cabinet 59 C-5 Compressor Control Cabinet 60 C-6 Compressor Control Cabinet 61 RP-1 Disconnect 62 RP-2 Disconnect 63 RP-3 Disconnect 64 RP-4 Disconnect AMMONIA COMPRESSOR MEZZANINE 65 SF-RF12 Combination Starter 66 SF-RF11 Combination Starter 67 EF-REF13 Combination Starter 68 EF-REF12 Combination Starter 69 EF-REF11 Combination Starter 70 SF-RF13 Combination Starter Fault #

15 No. Equipment Operating Visually Inspected MAINTENANCE SHOP AREA Fault # 71 (Left) Main Battery Charger Switch 72 (Right) Main Battery Charger Switch 73 EF-BC1 Combination Starter 74 EF-BM1 Combination Starter 75 SF-BM1 Combination Starter 76 SF-BC1 Combination Starter MAINTENANCE SHOP MEZZANINE 77 LPBE 480/277 Volt Distribution Panel 78 UPS-2 208/120 Volt Distribution Panel 79 Heat Trace Control Panel HTCP-1 80 RP3 208/120 Volt Distribution Panel 81 FMR TR3 45 KVA Siemens 3ø Transformer 82 LP3 480/277 Volt Distribution Panel 83 LPB-3 480/277 Volt Distribution Panel 84 LPB-1 480/277 Volt Distribution Panel 85 LPB-2 480/277 Volt Distribution Panel 86 RP /120 Volt Distribution Panel 87 RP /120 Volt Distribution Panel 88 FMR TR2 45 KVA Siemens 3ø Transformer 89 LP /277 Volt Distribution Panel 90 LP /277 Volt Distribution Panel 91 LP /277 Volt Distribution Panel AIR COMPRESSOR ROOM 92 Air Compressor #A Control Cabinet 93 Air Compressor #A Disconnect 94 Air Compressor #B Control Cabinet 95 Air Compressor #B Disconnect 96 Air Dryer Disconnect

16 No. Equipment Operating Visually Inspected 97 EF-DW5 Combination Starter 98 SF-DW2 Combination Starter 99 EF-DW6 Combination Starter 100 SF-DW1 Combination Starter 101 EF-DW4 Combination Starter 102 SF-DW3 Combination Starter 103 EF-DW3 Combination Starter 104 SF-DW4 Combination Starter 105 EF-DW2 Combination Starter 106 SF-DW5 Combination Starter 107 EF-DW1 Combination Starter 108 SF-DW6 Combination Starter Not In Service 109 SF-DW6 Drive Cabinet Not In Service 110 EF-ACP1 Combination Starter RAIL DOCK 111 EF-RC1 Combination Starter 112 SF-RD22 Combination Starter 113 SF-RD12 Combination Starter 114 SF-RD32 Combination Starter 115 SF-RC1 Combination Starter 116 SF-RD31 Combination Starter 117 EF-RD3 Combination Starter 118 SF-RD21 Combination Starter 119 EF-RD2 Combination Starter 120 SF-RD11 Combination Starter 121 EF-RD1 Combination Starter 122 LP /277 Volt Distribution Panel 123 LP /277 Volt Distribution Panel 124 LP /277 Volt Distribution Panel Fault #

17 No. Equipment Operating Visually Inspected RAIL DOCK MEZZANINE Fault # 125 LP7 480/277 Volt Distribution Panel 126 RP7 208/120 Volt Distribution Panel 127 FMR TR7 30 KVA Siemens 3ø Transformer 128 Heat Trace Control Panel HCTP LP8 480/277 Volt Distribution Panel 130 FMR TR8 30 KVA Siemens 3ø Transformer 131 RP8 208/120 Volt Distribution Panel 132 LP8E 480/277 Volt Distribution Panel OFFICE AREA ROOM 205 ELEVATOR MECHANICAL ROOM 133 Elevator Control Cabinet 134 Elevator Disconnect 135 Elevator Cab Lights Disconnect ROOM 227 ELECTRICAL ROOM 136 LPC 480/277 Volt Distribution Panel 137 LPCE 480/277 Volt Distribution Panel 138 FMR TR6 150 KVA Siemens 3ø Transformer 139 RP /120 Volt Distribution Panel 140 RP /120 Volt Distribution Panel 141 LP /277 Volt Distribution Panel 142 LP /277 Volt Distribution Panel 143 Main Switch KVA Siemens 3ø Transformer 145 RP /120 Volt Distribution Panel 146 RP /120 Volt Distribution Panel

18 No. Equipment Operating Visually Inspected ROOM 509 KITCHEN 147 KP1 208/120 Volt Distribution Panel Fault # ROOM 521 ELECTRICAL ROOM 148 RP /120 Volt Distribution Panel 149 RP /120 Volt Distribution Panel 150 Main Switch 151 PP /277 Volt Distribution Panel 152 PP /277 Volt Distribution Panel 153 RP /120 Volt Distribution Panel 154 RP /120 Volt Distribution Panel 155 FMR TR KVA Siemens 3ø Transformer ROOM 523 COMPUTER ROOM 156 UPS Control Cabinet TRUCK SHOP OUTSIDE 157 ATS Switchboard MDP5 480/277 Volt Distribution Panel 159 Switchboard MDP5E 480/277 Volt Distribution Panel KVA Siemens 3ø Transformer GARAGE FLOOR 161 FMR TM1 75 KVA Siemens 3ø Transformer 162 FMR TM4 30 KVA Siemens 3ø Transformer 163 FMR TM5 45 KVA Siemens 3ø Transformer 164 EF-2 Combination Starter 165 EF-13 Combination Starter 166 EF-14 Combination Starter 167 EF-19 Combination Starter ELECTRICAL ROOM

19 No. Equipment Operating Visually Inspected 168 MS1-N 208/120 Volt Distribution Panel Fault # 169 MS2 208/120 Volt Distribution Panel 170 MS /120 Volt Distribution Panel 171 MS /120 Volt Distribution Panel 172 LPG /277 Volt Distribution Panel 173 LPG /277 Volt Distribution Panel 174 LPG1E-1 480/277 Volt Distribution Panel 175 LPG1E-2 480/277 Volt Distribution Panel 176 LPG2 480/277 Volt Distribution Panel 177 ATS-2 TRUCK WASH BAY 178 EF-20 Combination Starter 179 EF-25 Combination Starter TRUCK WASH ELECTRICAL ROOM 180 Unlabeled 480/277 Volt Distribution Panel 181 Main Switch 182 EF-7 Combination Starter OIL ROOM 183 EF-1 Combination Starter 184 Air Compressor Control Cabinet 185 Air Compressor Disconnect 186 Air Dryer Disconnect GUARD SHACK 187 LPG3 208/120 Volt Distribution Panel 188 FMR TM KVA Siemens 1ø Transformer 189 GS1 208/120 Volt Distribution Panel PUMP HOUSE DIESEL ROOM

20 No. Equipment Operating Visually Inspected 190 Fire Pump Controller Control Cabinet Fault # 191 Jockey Pump Control Cabinet ELECTRICAL ROOM 192 Fire Pump Controller Control Cabinet 193 Fire Pump Controller Disconnect 194 Jockey Pump Control Cabinet 195 Jockey Pump Disconnect 196 PS1 208/120 Volt Distribution Panel 197 Transformer Disconnect 198 Pad Mounted Transformer (Fins Only) (Outside) ROOF-OFFICE AREA 199 RTU-A2-N Fuse Disconnect 200 RTU-A12 Fuse Disconnect 201 RTU-A11 Fuse Disconnect 202 RTU-A13 Fuse Disconnect 203 RTU-A2-S Fuse Disconnect 1 REFRIGERATION PENTHOUSE 204 AHU-14 Combination Starter 205 AHU-12 Combination Starter 206 AHU-10 Combination Starter 207 AHU-9 Combination Starter 208 AHU-11 Combination Starter 209 AHU-13 Combination Starter 210 AHU-15 Combination Starter 211 AHU-16 Combination Starter ROOF-WAREHOUSE COOLING TOWER AREA 212 EC 1 Fan 1 Disconnect

21 No. Equipment Operating Visually Inspected 213 EC 1 Fan 2 Disconnect Fault # 214 EC 1 Fan 3 Disconnect 215 EC 1 Pump 1 Disconnect 216 EC 2 Pump 2 Disconnect 217 EC 2 Fan 1 Disconnect 218 EC 2 Fan 2 Disconnect 219 EC 2 Fan 3 Disconnect PENTHOUSE #3 220 AHU #8 Combination Starter 221 AHU #7 Combination Starter 222 AHU #6 Combination Starter PENTHOUSE #5 223 AHU #17 Combination Starter 224 AHU #18 Combination Starter AHU #19 Combination Starter 226 AHU #20 Combination Starter 227 AHU #21 Combination Starter PENTHOUSE #4 228 AHU #22 Disconnect 229 AHU #23 Disconnect PENTHOUSE #2 230 AHU #4 Combination Starter 231 AHU #5 Combination Starter PENTHOUSE #1 232 AHU #3 Combination Starter 233 AHU #2 Combination Starter 234 AHU #1 Combination Starter

SYSCO INDIANAPOLIS INDIANAPOLIS, INDINA

SYSCO INDIANAPOLIS INDIANAPOLIS, INDINA November, 2017 Infrared Inspection Report Sysco Indianapolis LLC. 4000 West 62nd Street Indianapolis, Indiana, 46268 Company Contact: Trevor Gray Project: 05161117