SYSCO INDIANAPOLIS INDIANAPOLIS, INDINA

Transcription

1 SYSCO INDIANAPOLIS INDIANAPOLIS, INDINA November, 2017 Infrared Inspection Report Sysco Indianapolis LLC West 62nd Street Indianapolis, Indiana, Company Contact: Trevor Gray Project: CHARTER OAK DRIVE, LITTLE ROCK, AR PHONE: & FAX:

2 ORDER OF REPORT CONTENTS 1: Data To Facilitate Understanding & Utilizing Scan Report 2: Scan Results Overview & Action Taken Form 3: Identified Faulting Conditions, Information & Photographs 4: List Of Facility Equipment Identified By The Customer Representative & Notations Of Faulting Conditions Found DISCLAIMER This report and the recommendations contained in it are based upon conditions and practices observed and information made available to United Spectrographics personnel. This report does not purport to list all hazards or faulty conditions. It is not intended to indicate that other hazards or faulty conditions do not exist. Severity ratings in the report are based on the criteria shown in this report and are intended as guidelines only. No responsibility is assumed for the control of the facility s condition, maintenance practices or correction of conditions indicated herein. By issuing this report, neither United Spectrographics nor any of its employees makes any warranty, expressed or implied, concerning the contents of this report. Furthermore, neither United Spectrographics nor any of its employees shall be liable in any manner (other than liability that may be expressed in any policy of insurance that may be issued by United Spectrographics) for personal injury or property damage or loss of any kind arising from or connected with this inspection or failure to inspect.

3 Utilizing Report Contents Included in this report are Photographs and Thermographs of problem areas found during our recent Infrared Inspection of your facility. Each problem area picture is accompanied by: Date Location Information Temperature Calculations Color-coded Temperature Intensity and/or Condition Significance Data A Brief Comment Relating The Item In The Photograph To Its Corresponding Thermograph Suggested Corrective Recommendations. In most cases, problems (faults) found will be listed according to the date and order that they were located, rather then by significance or priority, as we feel that you and/or your personnel can best judge this, keeping in mind circuit importance and thermograph intensity. Thermal intensity is indicated by use of a color-coded data inserts that locate a fault s position on the standard electrical failure curve. The color of the insert represents the temperature range of the hottest item, or a portion of the item's circuitry, pointed out in the thermograph. The temperature ranges which the colored inserts represent are grouped as follows: INSERT Red Orange Yellow Green Temperature Range 70ºC/126ºF and higher above Ambient Operating Temp. 40ºC/72ºF to 69ºC/124ºF above Ambient Operating Temp. 25ºC/45ºF to 39ºC/70ºF above Ambient Operating Temp. *10ºC/18ºF to 24ºC/43ºF above Ambient Operating Temp. ( * See page 4)

4 Determining Cost Effective Responses Electrical equipment failures generally follow a standard mechanical/electrical failure curve. Dividing the failure curve into temp. ranges and locating a problems position on the curve allows us to indicate the probable time to its failure. Knowing a problems probable time to failure allows you to make a cost effective response to the problem areas that we locate. Below is a depiction of the electrical fault failure curve with the thermal intensity ranges and the colors that we assign to faults detailed in our reports. STANDARD ELECTRICAL FAULT FAILURE CURVE (Does Not Include Area In Blue) MINOR INTERMEDIATE SERIOUS CRITICAL DEVICE TEMP IS AMBIENT, BUT DEVICE IS EITHER FAULTY OR UNSAFE. 10ºC * 18ºF 25ºC 45ºF 40 C 72ºF 70 C 126ºF AMBIENT TEMP YEARS MONTHS MONTHS TO WEEKS WEEKS TO NOW FAULTY EQUIP Built In Trend Monitoring When yearly scans are accomplished, report results allow you to trend monitor your electrical equipment without having to cross reference previous report findings. If a previous years problem is not repaired it will show up again in the current scan report and its current intensity range indicates a current effective response.

5 Defining Total Temperature and Ambient Operating Temperature And Explanation For Their Use Total Temperature: Total Temperature = Ambient Operating Temperature + Fault temperature Allows you, the customer, to evaluate possible damage to equipment. Leads fail between 90ºC/194ºF and 110ºC/230º Phenolic fails around 200ºC/392ºF Transformers and Motor Insulation failure temperature depends on insulation class rating. Contacts start to fail around 130ºC/266ºF Ambient Operating Temperature (AOT*) for Infrared Scanning Purposes: Temperature within a device container (Box or Cabinet) that is not directly affected by faulting component = Normal Equipment Operating Temperature Contained By Box or Cabinet. If there is no container (Example: Device mounted to a wall) it is the temperature adjacent to the device not affected by the fault. Allows you, the customer, to determine if device will operate at intended amperage. Most switchgear is rated to operate at approximately 40ºC/104ºF (Industrial) to 50ºC/122ºF (Marine) If AOT is enough above normal rated temperature, either of the following conditions can cause an unanticipated trip. 1. An intermittent high load. 2. A minor (Green) or intermediate (Yellow) fault. Report pages with photographs: PH stands for Visible Light Photograph TH stands for Infrared Light Thermograph *AOT stands for Ambient Operating Temperature Both black & white and color infrared thermographs are presented to better depict the fault condition.

6 In addition to the corrective response time frame suggested below and the failure curve located on the previous page, you may want to consider using the military standard responses presented below. Military Standard For Evaluating Faults Located In Electrical Equipment Utilizing Temperature Data Obtained With Infrared Imaging Equipment: Temperatures rise above Ambient Operating Temperature: *10ºC/18ºF to 24ºC/43ºF component failure unlikely, but corrective measures required at next scheduled routine maintenance period or as scheduling permits. (Green Label) 25ºC/45ºF to 39ºC/70ºF component failure probable, unless corrected. (Yellow Label) 40ºC/72ºF to 69ºC/124ºF component failure almost certain, unless corrected. (Orange Label) 70ºC/126ºF and above component failure imminent. Immediately inform the person responsible for continued operation of equipment. (Red Label) Note: United Spectrographics uses a Blue Label to indicate faults that require attention due to either ambient temperature (Ex: Phase Not Operating), faulty equipment elements or unsafe conditions. * Note: Temperature conditions below 10ºC/18ºF rise above AOT are not considered significant enough to record and are usually not included in the reports unless the fault temperature is being affected by a cooling medium such as oil or wind. Fault Correction Recommendation When Our Source Assessment Is Inaccurate: When a fault is indicated in a connection or component and examination by your electrician does not turn up a loose connection or faulty component where we have indicated, a fault does exist. The electrician should continue to investigate the next connection or component to be found in the direction that the heat is coming from until a source is located. Example: If a molded case breaker line side lead connection lug is indicated as a fault source and is found to be secure, but not frozen in place, look for a loose connection or sign of over temp. in the lead holder lug.

7 SCAN RESULTS OVERVIEW PROMPT ATTENTION ITEMS: Because of: 1. The intensity or heat level indicated at the time of the scan. 2. Deterioration caused by excessive temperature not present at the time of the scan. 3. Physical condition irregularities observed at the time of the scan. We recommend that the following faults be given prompt attention: Faults: #1* Items With Asterisks Have High Total or Ambient Operating Temperatures. United Spectrographics November, 2017

8 SUMMARY OF FINDINGS FAULTS BY CATEGORY NUMBER OF FAULTS FAULT NO./ITEM NO. MINOR 0 0 INTERMEDIATE 0 0 SERIOUS 0 0 CRITICAL 1 1/25 SERIOUS 0 0 Number of items located at facility: 125 Number of faults: 1

9 ACTION TAKEN Sysco Indianapolis LLC. Indianapolis, Indiana November, 2017 Fault # Item # Category Repaired Monitor Date Name Serious

10 PROJECT: CUST REP: SCAN REP: Trevor Trey Dent DATE: November 16th, 2017 LOCATION: Warehouse 36 Volt Battery Charger Area Battery Labeled: Battery Connector PH # 1 > ITEM: SOURCE: TEMP: Connector Plug Negative Lead Lead connection crimp. Temp. of connection and crimp is: 98ºC / 208ºF Total Temp - 21ºC / 70ºF AOT = 77ºC / 138ºF above AOT. TH # 1 > COMMENTS TH # 1 > Abnormal heat is being generated in battery connector connection. See red arrows in PH#1 and TH#1. Loose and/or corroded contact areas. Clean, inspect and re-secure serviceable components. TEMPERATURE ABOVE AOT 77 C / 138 F

11 AREA/EQUIPMENT LIST Following is a list of the electrical equipment located at the Sysco Indianapolis LLC., Indianapolis, Indiana, facility and data relating to its operating condition at the time the scan was performed. NOTE: Items noted as visually inspected were not operational or show no visible load at the time of the inspection. No. Equipment Operating Visually Inspected EQUIPMENT LIST BUILDING A WAREHOUSE MAINTENANCE MAIN POWER AREA Fault # 1 C-14 Fuse Disconnect X 2 Panel CR Volt Distribution Panel X 3 HDR Fuse Disconnect X 4 DP Fuse Disconnect X 5 Switchgear X 6 Transformer Fuse Disconnect X 7 D-1 Fuse Disconnect X 8 D-2 Fuse Disconnect X 9 Panel E 208/120 Volt Distribution Panel X 10 Transformer Fuse Disconnect X 11 Office / Showroom 240 Volt Distribution Panel X 12 Panel B1 208/120 Volt Distribution Panel X 13 Transformer Hevi Duty 3ø 50KVA X WAREHOUSE 14 Panel-L 480 Volt Distribution Panel X 15 Panel-M 480/277 Volt Distribution Panel X 16 Transformer 3ø 45KVA X 17 KT ACME Transformer 3ø 75KVA X 18 Transformer Fuse Disconnect X 19 Battery Charger Panel 208/120 Volt Dist. Panel X 20 Unlabeled Fuse Disconnect X 21 Battery Charger Fuse Disconnect X

12 No. Equipment Operating Visually Inspected 22 Transformer Federal Pacific 3ø 75KVA X Fault # 23 KT-1 208/120 Volt Distribution Panel X 24 KT-2 208/120 Volt Distribution Panel X Volt Battery Charger Area X Volt Battery Charger Area X WAREHOUSE CAGE AREA 27 Panel-Z 208/120 Volt Distribution Panel X 28 Unlabeled Fuse Disconnect for Panel Z X WAREHOUSE ROOF ACCESS AREA 29 Panel-R 208/120 Volt Distribution Panel X 30 Hevi Duty Transformer 3ø 75KVA X 31 Panel-R Fuse Disconnect X 32 Refrigerator Fuse Disconnect X 33 A / Warehouse Ceiling Lights 240 Volt Dist. Panel X 34 Warehouse Lights Fuse Disconnect X 35 Panel-A 208/120 Volt Distribution Panel X Volt Fuse Disconnect X 37 Panel A1 Sub-panel 208/120 Volt Distribution Panel X 38 UPS 208/120 Volt Distribution Panel X FIRE PUMP ROOM 39 Fire Panel Control Cabinet X 40 Unlabeled 480/277 Volt Distribution Panel X DRY SIDE WAREHOUSE 41 XLS Fuse Disconnect X 42 Panel G 208/120 Volt Distribution Panel X 43 Panel M 208/120 Volt Distribution Panel X 44 Panel L 208/120 Volt Distribution Panel X 45 Transformer Riser Panel Fuse Disconnect X 46 Riser Panel I 208/120 Volt Distribution Panel X

13 No. Equipment Operating Visually Inspected 47 Transformer 3ø 75KVA X WILL CALL DOCK 48 Transformer X-9 X 49 Panel WC11 208/120 Volt Distribution Panel X 50 Panel WC12 208/120 Volt Distribution Panel X DRY SIDE LOADING DOCK 51 XLS Dock Panel 208/120 Volt Distribution Panel X 52 Sub Panel XLS 208/120 Volt Distribution Panel X 53 XLS2 Transformer X 54 Disconnect R25-27 X 55 P-1 208/120 Volt Distribution Panel X 56 Sub Panel P-1 208/120 Volt Distribution Panel X 57 UPS 208/120 Volt Distribution Panel X 58 P-1 Transformer X BREAK ROOM 59 Panel P1-A 208/120 Volt Distribution Panel X OFFICE BUILDING UPSTAIRS STORAGE 60 Office Panel A 208/120 Volt Distribution Panel X COMPUTER ROOM 61 Right Unlabeled 208/120 Volt Distribution Panel X 62 Left Unlabeled 208/120 Volt Distribution Panel X UTILITY CLOSET 63 Transformer Federal Pacific Singleø 25KVA X 64 CR-1 208/120 Volt Distribution Panel X 65 CR-2 208/120 Volt Distribution Panel X 66 Transformer Hevi Duty Singleø 37.5KVA X 67 Panel C 208/120 Volt Distribution Panel X 68 Panel A 208/120 Volt Distribution Panel X 69 Panel B 208/120 Volt Distribution Panel X Fault #

14 No. Equipment Operating Visually Inspected ELECTRICAL ROOM DOWN STAIRS Fault # 70 T-1 Transformer GE 3ø 75KVA X 71 P1A 208/120 Volt Distribution Panel X 72 P1B 208/120 Volt Distribution Panel X 73 L1 480/277 Volt Distribution Panel X 74 L2 Main Disconnect X 75 H2 Main Disconnect X 76 H1 480/277 Volt Distribution Panel X ELECTRICAL ROOM UPSTAIRS 77 UPS Panel 208/120 Volt Distribution Panel X 78 Sub-Panel P2A 208/120 Volt Distribution Panel X 79 P2A 208/120 Volt Distribution Panel X 80 L2 480/277 Volt Distribution Panel X 81 H2 480/277 Volt Distribution Panel X UPSTAIRS KITCHEN AREA 82 Unlabeled 208/120 Volt Distribution Panel X 83 Unlabeled 208/120 Volt Dist. Panel (under sink) X TELEPHONE ROOM 84 Unlabeled 208/120 Volt Distribution Panel X ELEVATOR CONTROL ROOM 85 Elevator Control Cabinet X 86 Elevator Fuse Disconnect X 87 Cab-Lights Fuse Disconnect X BARN 88 Panel N 208/120 Volt Distribution Panel X TRUCK SHOP 89 HVWB 480/277 Volt Distribution Panel X 90 TWB Transformer X 91 LVWB 208/120 Volt Distribution Panel X

15 No. Equipment Operating Visually Inspected BUILDING B FREEZER BUILDING MAIN ELECTRICAL ROOM Fault # 92 Switchgear #1 Sections 1-5 X 93 Switchgear #2 Sections 1-3 X 94 MCC 1 X 95 P2 480/277 Volt Distribution Panel X 96 P1 480/277 Volt Distribution Panel X 97 P3 208/120 Volt Distribution Panel X 98 P3-A 208/120 Volt Distribution Panel X 99 T1 Transformer GE 3ø 45KVA X 100 Transformer Federal Pacific 3ø 45KVA X COMPRESSOR ROOM 101 North Video Cameras Control Cabinet X 102 C1 Compressor Control Cabinet X 103 D2 Compressor Control Cabinet X Compressor Control Cabinet X Compressor Control Cabinet X 106 B4 Ammonia Pump Control Cabinet X 107 A5 Ammonia Pump Control Cabinet X BATTERY CHARGER AREA 108 PP4 480/277 Volt Distribution Panel X 109 Battery Chargers X FREEZER DOCK 110 HV2 480/277 Volt Distribution Panel X 111 LV2 208/120 Volt Distribution Panel X 112 HV1 480/277 Volt Distribution Panel X 113 LV1 208/120 Volt Distribution Panel X 114 HV3 480/277 Volt Distribution Panel X

16 No. Equipment Operating Visually Inspected COOLER RISER ROOM Fault # 115 Air Compressor Control Cabinet X 116 Air Compressor Fuse Disconnect X FREEZER AIR COMPRESSOR ROOM 117 Air Compressor Control Cabinet X 118 Air Compressor Fuse Disconnect X OUTSIDE 119 ATS 1 X 120 ATS 2 X 121 Utility Transformer 1 (Fins Only) X 122 Utility Transformer 2 (Fins Only) X 123 Mobile Generator Tap Box X 124 Transfer Switch X 125 Building A Emergency Panel X