PRODUCT DATASHEET Mira series last update 25/9/2012

Transcription

1 PRODUCT DATASHEET series last update 25/9/12 C1_MIRAM Lens Clear 32.4 mm 14.7 mm 25 degrees 81 % CA12878_MIRAM Assembly White 35 mm mm Tape 25 degrees 81 % 2. C121_MIRAW Lens Clear 32.4 mm 14.7 mm 39 degrees 82 % CA12879_MIRAW Assembly White 35 mm mm Tape 39 degrees 82 % 1. October 9th 12 14:53 Copyright Ledil Oy Subject to change without prior notice Page 1/3 Ledil Oy Salorankatu 242 SALO Finland ledil@ledil.com FAX:

2 PRODUCT DATASHEET series last update 25/9/12 C122_MIRAWW Lens Clear 32.4 mm 14.7 mm Glue 57 degrees 82 % CA1288_MIRAWW Assembly White 35 mm mm Tape 57 degrees 82 %.8 NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. October 9th 12 14:53 Copyright Ledil Oy Subject to change without prior notice Page 2/3 Ledil Oy Salorankatu 242 SALO Finland ledil@ledil.com FAX:

3 PRODUCT DATASHEET series last update 25/9/12 GENERAL INFORMATION Product series especially designed & optimized for series of s. Special care taken to make light distribution as uniform as possible. Lens material optical grade with high UV and temperature resistance (1 degrees of Celcius / 248 degrees of Fahrenheit). Allows use of high current and temperature conditions. Please find more information about used materials from below: Optic holder molded by high quality material (1 dergees of Celcius / 248 degrees of Fahrenheit). to heat sink with a PU foam adhesive tape of automotive grade. Please find fastening details by clicking link: to B with appropriate adhesive. By clicking link below you can find Ledil recommended glue options. NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. NOTE 2: Assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. Slanted assembly might cause unbalanced bond to the surface. All surfaces where tape is applied must be clean, dry and free from grease and dirt. If cleaning of B surfaces is needed, please follow strictly the cleaning instructions of your manufacturer this is important as cleaning shall under no circumstances damage s or other electronics components on the B. Further note that optical components shall not be cleaned with any chemicals only micro fiber cloth may be used to remove fingerprints or other traces from handling. NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. If cleaning of B surfaces is needed, please follow strictly the cleaning instructions of your manufacturer this is important as cleaning shall under no circumstances damage s or other electronics components on the B. Further note that optical components shall not be cleaned with any chemicals only micro fiber cloth may be used to remove fingerprints or other traces from handling. October 9th 12 14:53 Copyright Ledil Oy Subject to change without prior notice Page 3/3 Ledil Oy Salorankatu 242 SALO Finland ledil@ledil.com FAX:

4 Relative intensity of C1_MIRAM_(LuxeonM) %

5 Relative intensity of CA12878_MIRAM_(LuxeonM) %

6 Relative intensity of C121_MIRAW %

7 Relative intensity of CA12879_MIRAW_(LuxeonM) %

8 Relative intensity of C122_MIRAWW_LuxeonM %

9 Relative intensity of CA1288_MIRAWW_(LuxeonM) %

10 D C B A 4 D 4 Isometric view Bottom view Front view Dimension D: C1_MIRAM 29,7mm C121_MIRAW 28,4mm C122_MIRAWW 28,4mm Top view Material: 1 This drawing is our property. It can't be reproduced or communicated without our written agreement. DRAWN BY CHECKED BY DESIGNED BY D DATE mav sn mav DATE DATE DRAWING TITLE SIZE A4 DRAWING NUMBER Ledil Oy Salorankatu FIN 242 SALO Finland Datasheet MIRA lens SCALE 1:1 WEIGHT(g) SHEET 1/1 A REV 1 1