PRODUCT DATASHEET Laura series last update 17/9/2012

Transcription

1 PRODUCT DATASHEET series last update 17/9/2012 CA11959_LAURA-RS-PIN 21.6 x 21.6 mm 8 degrees 93 % CA12011_LAURA-SS-PIN 11 degrees 93 % CA11960_LAURA-D-PIN 13 degrees 93 % CA11837_LAURA-M-PIN 21.6 mm 30 degrees 92 % November 12th :14 Copyright Ledil Oy - Subject to change without prior notice - Page 1/4 Ledil Oy Salorankatu SALO Finland ledil@ledil.com FAX:

2 PRODUCT DATASHEET series last update 17/9/2012 CA12012_LAURA-O-PIN degrees 91 % CA12344_LAURA-W-PIN 47 degrees 92 % CA12325_LAURA-WW-PIN 21.6 mm 66 degrees 86 % CA12984_LAURA-REF-XW-PIN 72 degrees 86 % November 12th :14 Copyright Ledil Oy - Subject to change without prior notice - Page 2/4 Ledil Oy Salorankatu SALO Finland ledil@ledil.com FAX:

3 PRODUCT DATASHEET series last update 17/9/2012 NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. November 12th :14 Copyright Ledil Oy - Subject to change without prior notice - Page 3/4 Ledil Oy Salorankatu SALO Finland ledil@ledil.com FAX:

4 PRODUCT DATASHEET series last update 17/9/2012 GENERAL INFORMATION - Product series especially designed & optimized for series of s. - Special care taken to make light distribution as uniform as possible. - Lens material optical grade with high UV and temperature resistance (105 degrees of Celcius / 220 degrees of Fahrenheit). Allows use of high current and temperature conditions. Please find more information about used material from below: Lens material optical grade with high UV and temperature resistance (120 degrees of Celcius / 248 degrees of Fahrenheit). Allows use of high current and temperature conditions. Please find more information about used materials from below: - Reflector is made of aluminium coated (120 degrees of Celcius / 248 degrees of Fahrenheit) with protective lacquer (110 degrees of Celcius / 230 degrees of Fahrenheit). - Optic holder molded by high quality material (120 dergees of Celcius / 248 degrees of Fahrenheit). - to heat sink with a PU foam adhesive tape of automotive grade. Please find fastening details by clicking link: NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. NOTE 2: to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. Slanted assembly might cause unbalanced bond to the surface. All surfaces where tape is applied must be clean, dry and free from grease and dirt. If cleaning of B surfaces is needed, please follow strictly the cleaning instructions of your manufacturer - this is important as cleaning shall under no circumstances damage s or other electronics components on the B. Further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. November 12th :14 Copyright Ledil Oy - Subject to change without prior notice - Page 4/4 Ledil Oy Salorankatu SALO Finland ledil@ledil.com FAX:

5 Relative intensity of CA12984_LAURA-REF-XW-PIN () 125% 100% 75% 50% 25% % -70

6 D C 4 B A 2 O beam direction O-90 is opposite c/c Bottom view Lens 3 Holder 13.1 Front view 2 Tape Materials: lens: holder:, black Tape: PU Foam 1 This drawing is our property. It can't be reproduced or communicated without our written agreement. DRAWN BY pv CHECKED BY sn DESIGNED BY hh/mav D DATE DATE DATE DRAWING TITLE SIZE A4 Datasheet -Pin-tape assy DRAWING NUMBER Led Teh FIN Fin SCALE 2:1 WEIGHT(g) SHEET 1/1 - A REV 1

7

8