Marina Cabinets LIMOGES Cedex Telephone: Fax:

Transcription

1 87045 LIMOGES Cedex Telephone: Fax: Marina s CONTENTS Page 1. Main characteristics Range Technical characteristics Dimensions Equipments Mounting ccessories GENERL CHRCTERISTICS Grey polyester cabinets RL 7035, IP 66 - IK 10 (1) - Classe II, particularly suited to corrosive environments. Direct mounting of equipment at back of cabinet. Possible to fit a partial plate (cabinets height M 500 mm) and/or rails (cabinets height M 400 mm) on intermediate fixing points.. Optional: - equipments depth adjustment (cabinet height M 400 mm), - horizontal or vertical coupling (cabinet height M 500 mm), - reinforced protection with roof (cabinet height M 700 mm), - up to 7 solutions for cabinet mounting (with brackets, on base, on stand, etc...) 2. RNGE Cat. No(s) Dimensions Height x Width x Depth With plane With glass Overall Corresponding door door metal cabinets x 220 x x 200 x x 300 x x 300 x x 400 x x 400 x x 400 x x 400 x x 510 x x 500 x x 610 x x 600 x x 810 x x 800 x x 810 x x 800 x TECHNICL CHRCTERISTICS 3.1 Framework - Fibreglass filled polyester resin RL 7035 (SMC), heat polymerised, - one-piece body, without cable entries, - brass fixing inserts (only supplied with ), - top and bottom protective flange (except Cat. No ), - reversible door with captive pin (except Cat. No ) in stainless steel, opening 180 (130 for Cat. No ), - two-point closure with two plastic double bar locks (one bolt for Cat. No ) with interchangeable barrel, - polyurethane seal, - tinted tempered glass door. 3.2 Protection index, insulation class - IP 66 according to IEC EN 60529: totally protected against dust and totally protected against jets of water of similar force to heavy seas, - IK 10 according to IEC EN 62262: protected against mechanical impacts of 20 joules (IK 08 = 5 joules for Cat. No ), - conform to IEC EN 62208, - classe II: allow for the production of assemblies in total insulation according to IEC EN Mechanical resistance - maximum load: 500 kg / m 3, - maximum load on door: 2.5 kg per 100 mm height, - maximum static load with 4 fixing brackets: Cat. No (for cabinets height 300 mm) : 100 kg, Cat. No (for cabinets height M 400 mm) : 150 kg, - insert resistance: axial wrenching > 250 kg (by insert) - fixing with stand Cat. No /37 conform to EN (railway applications, permanent installations). 3.4 Resistance to climatic conditions - operating temperature: - 40 C to + 85 C (+ 100 C at peak), - salt spray according to ISO 9227 (NSS test) and IEC EN (Ka test): 1500 hours, - sulphur dioxide with condensation according to EN ISO 6988: 500 hours, - ultraviolet resistance (UV): exposure 240 hours according to EN ISO ( method) with ie < 2.5 (colorimetric variation). 3.5 Fire behaviour - glow wire resistance according to IEC EN : 960 C, - limited owygen index (LOI) according to EN ISO 4589 / STM D 2863: 22 %, - without halogens. (1) height 300 mm. 1/8

2 3. TECHNICL CHRCTERISTICS (continued) 3.6 Resistance to chemical agents Resistant to ambient temperature compared to exposure risk spraying. ++: Excellent resistance (continuous exposure) + : Good resistance (prolonged exposure) : Limited resistance (possible momentary exposure) : Weak resistance (exposure to be acoided) queous solutions lcohols Glycols Carbolic Cresols ases Strong oxidant acids Weak acids Oils and greases Hydrocarbons Cold water ++ Hot water + Vapor Saltwater 5 % + Hydrogen peroxide Water + detergent + Water + surfactants + ldehyde Ethanol + Methyl alcohol + Propanol + utanol + Ethylene glycol + mmoniia + Sodium hydroxide + Sodium hypoclorite + Potassium hydroxide + cetic acid + Nitric acid 5 % + Sulfuric acid 30 % + Muriatic acid 30 % + Perchloric acid 70 % ++ Hydrofluoric acid 70 % Chromic acid 50 % Phosphoric acid 30 % + Diluted acetic acid < 25 % + Citric acid ++ Lactic acid ++ Formic acid + Uric acid + From Lard ++ of animal origins utter and cream ++ Linseed oil ++ From of vegetable origins From of mineral origins Peanut and olive ++ Castor oil ++ Glycerin + Paraffin ++ Engin oil + Silicon oil ++ Machine oils ++ Hydraulic fluid + Unleaded gas + Diesel oil ++ Kerosene ++ White spirit ++ Chlorinated solvents romatic solvents liphatic solvents Fluoride solvents Ketones Terpenes Trychloroethylene Trichloroethane Perchloroethylene Methylene chloride Carbon tetrachloride Chloroform enzene + Toluene Xylene + Hexane ++ Heptane ++ Trichlorofluoromethane cetone Methyl ethyl ketone Ethyl acetate Turpentine 3.7 Painting behaviour fter having used sandpaper (grain 400 to 600) and degreasing, Marina cabinets can be painted using a polyurethane component paint. The application of a bonding primer allows the use of all types of paint. 4. DIMENSIONS 4.1 Overall dimensions/weight H L Overall dimensions Weight Weight with H x L x P (kg) glass door (kg) x 220 x / x 300 x / x 400 x / x 400 x / x 510 x / x 610 x / x 810 x / x 810 x P 2/8

3 4. DIMENSIONS (continued) 4.2 Dimensions for the window (glass door) Window centred in height and width. Useable dimensions (1) (1) C D E F G H I maxi J / / / / / / / (1) Except cabinets with glass door Marking every 50 mm (25 mm for ) inside the door. 4.3 Useable dimensions Thiekness of wall (indicative dimensions) Door Sides Rear / / / / / / / Equipment fixing Direct fixing at back of cabinet. Intermediate fixing points for partial plate (except /51/71) and rails (except ). J E D 26 C C E E D 26 F I H F C G Dimensions C D E F / / / / / / / /8

4 4. DIMENSIONS (continued) 4.5 Equipment adjustment Depth adjustment using kit (except ). 5. EQUIPMENTS 5.1 Plain plates, Lina 12.5, perforated Lina 25 Lina 12.5 Lina 25 - Total plates: Total plate Chassis with rail max. min. max. min. with Cat. with Cat. No No / / / / / / / s Total plate H x L Plain Lina 12.5 Lina x / x / x / x / x / x / x / x Partial plates: Rail angled at 45 with supports Set of 4 wall mounting brackets Example of a cabinet with partial plate and rail mounted on intermediate studs. s Plates H x L Partial plates Plain Lina 12.5 Lina / x / x / x / x / x / x /8

5 1.5 Marina s 5. EQUIPMENTS (continued) 5.2 Sectioned uprights and Lina 25 rails For chassis production - Uprights: 8, Internal door H x L / x / x / x / x / x / x / x (1) (1) Internal door like with adjustable distance of 200 mm at top and bottom of door Chassis with insulating plates RL Rails: Uprights Height (set of 2) / / / / / / / m to be cut to length Rail Faceplate lanking plate End strip Chassis 15 Width Rail / /55/72/ / / /64/83/ m to be cut to lenght H x L x P Capacity / x 300 x rows of 10 modules / x 400 x rows of 16 modules / x 400 x rows of 16 modules / x 500 x rows of 21 modules / x 600 x rows of 27 modules / x 800 x rows of 38 modules / x 800 x rows of 38 modules - Mounting plate for chassis: 5.3 Internal polyester doors RL 7035 Chassis Mouting plate H x L x P For power devices x 600 x DPX 125, DPX160 ou Vistop x 800 x x 800 x DPX 125, DPX 160, DPX 250 ER, Vistop 160 ou Vistop 250 5/8

6 5. EQUIPMENTS (continued) 5.5 VDI chassis On stand On post Direct fixing with kit outside and by threaded /47/ mounting rods /47/48/49 equipment area and by threaded and on stand rods (mm 3 ) C D E F / / / / , / , / / VDI chassis H x L x P Capacity / x 400 x U (1) / x 600 x U (2) (1) For same equipment as mini XL VDI cabinet (2) For 19-inch equipment. 6. FIXING Rear fixing on inserts (no passthrough) maintains IP66 and Class II. Direct fixing With With through rear vertical brackets horizontal brackets of cabinet (mm 3 ) G H R S V T U Y (1)(2) / / / / / / / (1) With brackets (2) S and T: insert centre distances (3) Through fixing - Wall fixing with brackets: Y U S V R T Set of brackets RL D F For cabinet H 300 mm Polyamide H Ø 18 E C G For cabinets H 400 mm Polyester Polyamide cover RL /8

7 6. FIXING (continued) - Wall fixing by threaded rods: - Floor fixing on plinth H 170 mm (polyester RL 7035): Roof RL /94/95 M8 Plinth Insert x 250 mm 600 x 300 mm 800 x 300 mm 600 x 300 mm 800 x 300 mm 7. CCESSORIES - Fixing on post: Réf /47/48/ Joining kit s can be joined horizontally or vertically with Cat. Nos /51/71). The kit is composed of: - 2 linking pieces of fixing brackets ( to be ordered separately) stainless steel, - 1 cable crossing frame in glassfibre-filled polyester with integrated polyurethane seals, - 1 drilling template, screw in stainless steel. IP 66, Class II and max. load (500 kg/m 3 ) are maintained. Link piece Floor fixing with stand: Stand /37 (H 1203/1603 mm) Cable crossing useable passage 80 x mm nti-tipping cross-pieces (optional) From height 800 mm upwards 2 cable crossign frames can be fitted on the height of the cabinet. Stand is supplied with accessories to maintain IP 66 and Class II at the level of the passthrough fixing. 7/8

8 7. CCESSORIES (continued) 7.2 Cabstop Kit RL Kit enables mounting of IP 55 Cabstop plates on flat surface. Kit enables mounting of 2 IP 55 Cabstop plates Cat. Nos or 95, and or 97 (supplied with drilling template). Class II is maintained (insulated screws). 7.5 Self adhesive pockets for plans - Cat. Nos , 340 x 235 mm (internal dimensions: 310 x 200 x 18 mm) and Cat. Nos , 260 x 165 mm (internal dimensions: 230 x 130 x 18 mm). Opened, RL 7035 Cabstop plate /95/96/ , 325 x 120 mm (internal dimensions: 324 x 120 x 18 mm). Closed IP 50, RL Capacity of some fifteen 4 sheets of papers folded in two , 305 x 220 mm (4 format). Flexible and transparent. 7.6 Door contact Handle lock with barrel Handle lock is composed of a 2433 barrel. IP 66 maintained. Handle lock and other key codes possible. 7.4 Stainless steel padlocking lug The lug allows the padlocking of cabinets (except ) with 3 padlocks Ø 6 mm max. in addition to the locks. IP and Class II are maintained Other padlocking possible: on lock (or handle lock in accessory). 8/8