Hose and Fitting Edition
|
|
- Brandon Pope
- 5 years ago
- Views:
Transcription
1 and Fitting Edition Phone: Fax:
2 Table of Contents Determining Size 3 Selection Table 4 1SC, 100R2AT 5 100R16, 100R17 6 Jackhose, 2SN 7 4SP, 4SH 8 100R13, 100R15 9 OFW-Oilfield Workover 10 Waterblast, Grease Injection Waterblast and Grease Injection Fittings 13 Hydraulic Fitting Guide 14 Non Skive 1-Piece Fittings- 200, 400, 600 Series Interlock 2-Piece, Fittings Series High and Fittings 31 VHP - 10,000 PSI Thermoplastic 32 VHP Fittings Chemical Compatibility Chart Phone: Fax:
3 Determining Size Determining Size (ID) For Hydraulic Systems Determining proper hose selection is critical for efficient and trouble free operation of hydraulic power systems. Selection of proper hoses involves choosing the correct tube material, type, pressure, and size. The hose selection Table-1A, located on the next page ensures proper sizing practices for inside diameter for hydraulic hoses. Proper sizing of the hose for various parts of a hydraulic system results in an optimum combination of efficient and cost effective performance. A hose that is sized too small causes high fluid velocity, which has many detrimental effects. In suction lines, it causes cavitation which starves and damages pumps. In pressure lines it causes high friction losses and turbulence. Both resulting in high pressure drops and heat generation. High heat accelerates wear in moving parts and rapid aging of hoses, all resulting in reduced component life. High heat generation also means wasted energy, and low efficiencies in the hydraulic power system. Sizing a hose too large increases system cost. Thus, optimum hose sizing is very criticial. The following is a simple procedure to determine required flow diameter for the required flow rate and type of line being sized in the power system. lines - 25 ft per second maximum (velocity) Return lines - 10 ft per second maximum (velocity) Suction lines - 4 ft per second maximum (velocity) If you desire to use different velocities (ft per sec) than chart 1A recommends, then use the following formula oil velocity (ft per sec) GPM x = = ID oil velocity (ft per sec) Phone: Fax:
4 Selection Table Selection Table - 1A Maximum Flow Rate GPM Recommended Flow Diameter in Inches Lines Return Lines Suction Lines Maximum Flow Rate GPM Recommended Flow Diameter in Inches Lines Return Lines Suction Lines Phone: Fax:
5 Hydraulic s 1SC 1- Synthetic Rubber Tube 2- One High Tensile Steel Wire Braid 3- Synthetic Rubber Cover Tube: Oil resistant, synthetic rubber Reinforcement: one braid of high tensile steel wire Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Petroleum based hydraulic fluid, gasoline, water, diesel fuels, lubricating oils, glycol, mineral oils, and more Termination: 200 series, bite to wire, 1-piece fitting Key Note: compact one wire braid, high flexibility and excellent bend radius 100R2AT O.D. 1- Synthetic Rubber Tube 2- Two High Tensile Steel Wire Braids 3- Synthetic Rubber Cover O.D. Max Working Max Working Burst Burst Bend Radius Tube: Oil resistant, synthetic rubber Reinforcement: Two braids of high tensile steel wire Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Petroleum based hydraulic fluid, gasoline, water, diesel fuels, lubricating oils, glycol, mineral oils, and more Termination: 200 series, bite to wire, 1-piece fitting Key Note: Wide range of standard hydraulic use Bend Radius Weight Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type ISC-12 3/ ,520 6, series/1-piece ISC ,280 5, series/1-piece ISC / , series/1-piece ISC / , series/1-piece ISC , series/1-piece Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type 100R2AT-04 1/ ,800 23, series/1-piece 100R2AT-06 3/ ,800 19, series/1-piece 100R2AT-08 1/ ,000 16, series/1-piece 100R2AT-10 5/ ,630 14, series/1-piece 100R2AT-12 3/ ,120 12, series/1-piece 100R2AT ,400 9, series/1-piece 100R2AT / ,820 7, series/1-piece 100R2AT / ,310 5, series/1-piece 100R2AT ,160 4, series/1-piece Phone: Fax:
6 100R16 1- Synthetic Rubber Tube 2- Two High Tensile Steel Wire Braids 3- Synthetic Rubber Cover Tube: Oil resistant, synthetic rubber Reinforcement: Two braids of high tensile steel wire Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Petroleum based hydraulic fluid, gasoline, water, diesel fuels, lubricating oils, glycol, mineral oils, and more Termination: 200 series, bite to wire, 1-piece fitting Key Note: Lightness and flexibility with 2-wire pressure ratings I.D. O.D. Max Working Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type 100R / ,000 20, series/1-piece 100R / ,000 16, series/1-piece 100R / ,500 14, series/1-piece 100R17 Tube: Oil resistant, synthetic rubber Reinforcement: 1/4, 3/8 and 1/2 - one wire braid; 3/4 and 1 - two wire braid Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Petroleum based hydraulic fluid, gasoline, water, diesel fuels, lubricating oils, glycol, mineral oils, and more Termination: 200 series, bite to wire, 1-piece fitting 1- Synthetic Rubber Tube 2- One or Two High Tensile Steel Wire Braids 3- Synthetic Rubber Cover Key Note: 3,000 PSI constant pressure, lightweight with good flexibility I.D. O.D. Max Working Burst Bend Radius 6 Phone: Fax: Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type 100R / ,000 12, series/1-piece 100R / ,000 12, series/1-piece 100R / ,000 12, series/1-piece 100R / ,000 12, series/1-piece 100R ,000 12, series/1-piece
7 Jack 1- Synthetic Rubber Tube 2- Two High Tensile Steel Wire Spirals 3- Synthetic Rubber Cover Tube: Oil resistant, synthetic rubber Reinforcement: Two braids of high tensile steel wire Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Hydraulic oil, water Termination: 200 series, bite to wire, 1-piece fitting Key Note: 10,000 PSI static pressures, hydraulic lifting jacks, hydrostatic testing I.D. O.D. Max Working Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type jackhose-04 1/ ,000 20, series/1-piece jackhose-06 3/ ,000 20, series/1-piece DIN-2SN 1- Synthetic Rubber Tube 2- Two High Tensile Steel Wire Braids 3- Synthetic Rubber Cover I.D. O.D. Max Working Tube: Oil resistant, synthetic rubber Reinforcement: Two braids of high tensile wire Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Petroleum based hydraulic fluid, gasoline, water, diesel fuels, lubricating oils, glycol, mineral oils, and more Termination: 200 series, bite to wire, 1-piece fitting Key Note: 1/2 5,000 PSI working pressure with 4 to 1 safety factor Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type 2SN-08 1/ ,000 20, Series/1-Piece Phone: Fax:
8 DIN-4SP 1- Synthetic Rubber Tube 2- Four High Tensile Steel Wire Spirals 3- Synthetic Rubber Cover Tube: Oil resistant, synthetic rubber Reinforcement: Four spirals of high tensile steel wire Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Petroleum based hydraulic fluid, gasoline, water, diesel fuels, lubricating oils, glycol, mineral oils, and more Termination: 402 series, 2-piece skive fittings Key Note: High impulse cycles I.D. O.D. Max Working Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type 4SP-08 1/ ,018 24, Series/2-piece DIN-4SH 1- Synthetic Rubber Tube 2- Four High Tensile Steel Wire Spirals 3- Synthetic Rubber Cover Tube: Oil resistant, synthetic rubber Reinforcement: Four spirals of high tensile wire Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Petroleum based hydraulic fluid, gasoline, water, diesel fuels, lubricating oils, glycol, mineral oils, and more Termination: 400 series, non skive, 1-piece fitting Key Note: High impulse cycles I.D. O.D. Max Working Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type 4SH-12 3/ ,090 24, /1-piece 4SH ,510 22, /1-piece 4SH / ,000 20, /1-piece 4SH / ,205 16, /1-piece 4SH ,625 14, /1-piece 8 Phone: Fax:
9 100R13 1- Synthetic Rubber Tube 2- Six High Tensile Steel Wire Spirals 3- Synthetic Rubber Cover Tube: Oil resistant, synthetic rubber Reinforcement: 3/4 to 1-1/4 - four spiral wires; 1-1/2 and 2 - six spiral wires Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Petroleum based hydraulic fluid, gasoline, water, diesel fuels, lubricating oils, glycol, mineral oils, and more Termination: 600 series, non skive, 1-piece fitting Key Note: 5,000 PSI constant pressure, high impulse cycle I.D. O.D. Max Working Burst Bend Radius Weight Phone: Fax: Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type 100R / ,000 20, series/1-piece 100R ,000 20, series/1-piece 100R / ,000 20, series/1-piece 100R / ,000 20, series/1-piece 100R ,000 20, series/1-piece 100R15 1- Synthetic Rubber Tube 2- Six High Tensile Steel Wire Spirals 3- Synthetic Rubber Cover I.D. O.D. Max Working Tube: Oil resistant, synthetic rubber Reinforcement: 3/4 and 1 - four spiral wires; 1 to 1-1/2 - six spiral wires Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Petroleum based hydraulic fluid, gasoline, water, diesel fuels, lubricating oils, glycol, mineral oils, and more Termination: 400 and 600 series, non skive, 1-piece fitting Key Note: 6,000 PSI constant pressure, high impulse cycle Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Couplings 100R W 3/ ,000 24, series/1-piece 100R W ,000 24, series/1-piece 100R ,000 24, series/1-piece 100R / ,000 24, series/1-piece 100R / ,000 24, series/1-piece 9
10 OFW-Oilfield Workover 1- Synthetic Rubber Tube 2- Four High Tensile Steel Wire Spirals 3- Synthetic Rubber Cover Tube: Oil resistant, synthetic rubber Reinforcement: Four spirals of high tensile wire Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +212 F, Intermittent use up to 250 F Application: Oilfield workover rigs and well servicing Not to be used with hydraulic systems Termination: 400 series, non skive, 1-piece fitting Key Note: 5,000 PSI working pressure with 2.9 to 1 safety factor when used on oilfield workover rigs and well servicing applications I.D. O.D. Max Working Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type OFW ,000 14, series/1-piece 10 Phone: Fax:
11 Specialty Grease Injection and Waterblast Phone: Fax:
12 Specialty s and Fittings WB-Waterblast 15,000 PSISI 1- Synthetic Rubber Tube 2- Four High Tensile Steel Wire Spirals 3- Synthetic Rubber Cover Tube: Oil resistant, synthetic rubber Reinforcement: Multiple Spiral Technology Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +213 F, Intermittent use up to 250 F Application: Waterblasting market Termination: WB series, interlock, external/internal skive, 2-piece fittings Key Note: Waterblasting market I.D. O.D. Max Working Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type WB-08-15K 1/ ,000 37, WB/2-piece GI-Grease Injection -15,000 PSI 1- Synthetic Rubber Tube 2- Four High Tensile Steel Wire Spirals 3- Synthetic Rubber Cover Tube: Oil resistant, synthetic rubber Reinforcement: Multiple Spiral Technology Cover: Oil and weather resistant synthetic rubber Temperature: -40 F / +213 F, Intermittent use up to 250 F Application: Grease injection, glycol, traces of sour gas Termination: GI series, interlock, external/internal skive, 2-piece fittings Key Note: Used in wireline market for grease injection services. cover must be pin pricked when being used with sour gas I.D. O.D. Max Working Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Fitting Type GI-08-15K 1/ ,000 37, GI/2-piece 12 Phone: Fax:
13 Grease Injection Fitting Waterblast Ferrule Material Thread GI-NPT K 1/2 Carbon Steel 1/2 NPT GI-M16FX-08 1/2 Carbon Steel 1 Type M Swivel GI-NPT K-SS 1/2 Stainless Steel 1/2 NPT GI-M16FX-08-SS 1/2 Stainless Steel 1 Type M Swivel Material Thread WB-NPT K 1/2 Carbon Steel 1/2 NPT WB-M16FX-08 1/2 Carbon Steel 1 Type M Swivel WB-NPT K-SS 1/2 Stainless Steel 1/2 NPT WB-M16FX-08-SS 1/2 Stainless Steel 1 Type M Swivel Material GI-Ferrule-08-15K 1/2 Carbon Steel GI-Ferrule-08-15K-SS 1/2 Stainless Steel WB-Ferrule-08-15K 1/2 Carbon Steel WB-Ferrule-08-15K-SS 1/2 Stainless Steel Phone: Fax:
14 Hydraulic Fitting Guide 200 Series- 1-Piece, Non-Skive Types: 1SC, 100R2AT, 2SN, 100R16, 100R17, Jackhose 400 Series- 1-Piece, Non-Skive Types: 100R12 and 4SH 600 Series- 1-Piece, Non-Skive Types: 100R13 and 100R Series- 2-Piece, Internal and External Skive Types: 100R13 and 100R Series - 2-Piece - Skive Type Types: 1/2 4SP 14 Phone: Fax:
15 Non-Skive 1-Piece Fittings 200 Series, 400 Series, and 600 Series Phone: Fax:
16 Non-Skive 1-Piece Fittings MALE NPT A B H1 Thread 200-NPT P 1/ / NPT P 1/ / NPT P 1/ / NPT P 1/ / NPT P 3/ / NPT P 3/ / NPT P 3/ / NPT P 1/ / NPT P 1/ / NPT P 1/ / NPT P 5/ / NPT P 5/ / NPT P 3/ / NPT P 3/ / NPT P 3/ NPT P NPT P 1-1/ / NPT P 1-1/ / NPT P NPT P 3/ / NPT P NPT P 1-1/ / NPT P 1-1/ / NPT P MALE NPT-API 600-NPT P 3/ / NPT P NPT P 1-1/ / NPT P 1-1/ / A B H1 Thread 400-NPT-API P NPT-API P Phone: Fax:
17 MALE NPT SWIVEL A B H1 Thread 200-NPTX P 1/ / NPTX P 3/ / NPTX P 3/ / NPTX P 3/ / NPTX P 1/ / NPTX P 1/ / NPTX P 3/ / NPTX P MALE JIC 37 A B H1 Thread 200-MJ P 1/ /16 -UNF MJ P 1/ /16 -UNF MJ P 3/ /16 -UNF MJ P 3/ /4 -UNF MJ P 1/ /4 -UNF MJ P 1/ /8 -UNF MJ P 1/ /16 -UNF MJ P 5/ /8 -UNF MJ P 5/ /16 -UNF MJ P 3/ /16 -UNF MJ P 3/ /16 -UNF MJ P /16 -UNF MJ P 1-1/ /8 -UNF-12 Phone: Fax:
18 37 FEMALE JIC SWIVEL, STRAIGHT A B C H1 H2 Thread 200-FJX P 1/ /16 -UNF FJX P 1/ /16 -UNF FJX P 3/ /16 -UNF FJX P 3/ /16 -UNF FJX P 3/ /4 -UNF FJX P 1/ /16 -UNF FJX P 1/ /4 -UNF FJX P 1/ /8 -UNF FJX P 1/ /16 -UNF FJX P 5/ /8 -UNF FJX P 5/ /16 -UNF FJX P 3/ /16 -UNF FJX P 3/ /16 -UNF FJX P /16 -UNF FJX P /8 -UNF FJX P 1-1/ /8 -UNF FJX P 1-1/ /8 -UNF FJX P /2 -UNF FJX P 3/ /16 -UNF FJX P /16 -UNF FJX P 1-1/ /8 -UNF FJX P 1-1/ /8 -UNF FJX P /2 -UNF-12 FEMALE JIC SWIVEL, FJX P 3/ /16 -UNF FJX P /16 -UNF FJX P 1-1/ /8 -UNF FJX P 1-1/ /8 -UNF FJX P /2 -UNF-12 I.D. A B C D H1 Thread 200-FJX P 1/ /16 -UNF FJX P 1/ /16 -UNF FJX P 3/ /16 -UNF FJX P 3/ /4 -UNF FJX P 1/ /4 -UNF FJX P 1/ /8 -UNF Phone: Fax:
19 FEMALE JIC SWIVEL, 45 CONTINUED I.D. A B C D H1 Thread 200-FJX P 5/ /8 -UNF FJX P 5/ /16 -UNF FJX P 3/ /16 -UNF FJX P /16 -UNF FJX P 1-1/ /8 -UNF FJX P 3/ /16 -UNF FJX P /16 -UNF FJX P 1-1/ /8 -UNF FJX P 1-1/ /8 -UNF FJX P /2 -UNF-12 FEMALE JIC SWIVEL, 90 I.D. A B C D H1 Thread 200-FJX P 1/ /16 -UNF FJX P 1/ /16 -UNF FJX P 3/ /16 -UNF FJX P 3/ /4 -UNF FJX P 1/ /16 -UNF FJX P 1/ /4 -UNF FJX P 1/ /8 -UNF FJX P 1/ /16 -UNF FJX P 5/ /8 -UNF FJX P 5/ /16 -UNF FJX P 3/ /16 -UNF FJX P 3/ /16 -UNF FJX P /16 -UNF FJX P 1-1/ /8 -UNF FJX P 1-1/ /8 -UNF FJX P /2 -UNF FJX P 3/ /16 -UNF FJX P /16 -UNF FJX P 1-1/ /8 -UNF FJX P 1-1/ /8 -UNF FJX P /2 -UNF-12 Phone: Fax:
20 37 FEMALE JIC SWIVEL 90 LONG O RING FACE SEAL SWIVEL, STRAIGHT A B C D H1 Thread 200-FJX90L P 1/ /16 -UNF FJX90L P 3/ /16 -UNF FJX90L P 3/ /4 -UNF FJX90L P 1/ /4 -UNF FJX90L P 1/ /8 -UNF FJX90L P 5/ /8 -UNF FJX90L P 3/ /16 -UNF FJX90L P /16 -UNF FJX90L P 1-1/ /8 -UNF-12 A B C H1 H2 Thread 200-ORFS P 1/ / ORFS P 1/ / ORFS P 3/ / ORFS P 3/ / ORFS P 1/ / ORFS P 1/ ORFS P 1/ / ORFS P 5/ ORFS P 5/ / ORFS P 3/ / ORFS P 3/ / ORFS P / ORFS P / ORFS P 1-1/ / ORFS P 1/ / ORFS P 1/ ORFS P 3/ / ORFS P 3/ / ORFS P / Phone: Fax:
21 O RING FACE SEAL, 45 C B H 1 D A A B C D H1 Thread 200-ORFS P 1/ / ORFS P 1/ / ORFS P 3/ / ORFS P 3/ / ORFS P 1/ / ORFS P 1/ ORFS P 5/ ORFS P 5/ / ORFS P 3/ / ORFS P 3/ / ORFS P / ORFS P / ORFS P 1-1/ / ORFS P 1/ / ORFS P 3/ / ORFS P 3/ / ORFS P /16-12 O RING FACE SEAL, 90 A B C D H1 Thread 200-ORFS P 1/ / ORFS P 1/ / ORFS P 3/ / ORFS P 3/ / ORFS P 1/ / ORFS P 1/ ORFS P 5/ ORFS P 5/ / ORFS P 3/ / ORFS P 3/ / ORFS P / ORFS P / ORFS P 1-1/ / ORFS P 1/ / ORFS P 3/ / ORFS P 3/ / ORFS P / Phone: Fax:
22 MALE O RING BOSS A B H1 Thread 200-MB P 1/ / MB P 1/ / MB P 3/ / MB P 3/ / MB P 1/ / MB P 1/ / MB P 5/ / MB P 5/ / MB P 3/ / MB P /16-12 FEMALE NPT A B H1 Thread 200-FP P 1/ / FP P 1/ / FP P 3/ / FP P 1/ / FP P 3/ / FP P FEMALE PIPE SWIVEL A B H1 Thread 200-FPX P 1/ / FPX P 3/ / FPX P 3/ / FPX P 1/ / FPX P 3/ / FPX P 3/ FPX P FPX P 1/ / FPX P 3/ / FPX P Phone: Fax:
23 FEMALE BRITISH SWIVEL, STRAIGHT A B C H1 H2 Thread 200-FBX P 1/ / FBX P 1/ / FBX P 3/ / FBX P 3/ / FBX P 1/ / FBX P 5/ / FBX P 3/ / FBX P FBX P 1-1/ /4-11 FEMALE BRITISH SWIVEL, FBX P 3/ / FBX P FBX P 1-1/ /4-11 A B C D H1 Thread 200-FBX P 1/ / FBX P 1/ / FBX P 3/ / FBX P 3/ / FBX P 1/ / FBX P 5/ / FBX P 3/ / FBX P FBX P 1-1/ /4-11 FEMALE BRITISH SWIVEL, FBX P 3/ / FBX P FBX P 1-1/ /4-11 A B C D H1 Thread 200-FBX P 1/ / FBX P 1/ / FBX P 3/ / FBX P 3/ / FBX P 1/ / FBX P 5/ / Phone: Fax:
24 FEMALE BRITISH SWIVEL, 90 CONTINUED... A B C D H1 Thread 200-FBX P 3/ / FBX P FBX P 1-1/ /4-11 MALE BRITISH 400-FBX P 3/ / FBX P FBX P 1-1/ /4-11 B A A B H1 Thread 200-MBSPP P 1/ / MBSPP P 3/ / MBSPP P 1/ / MBSPP P 3/ / MBSPP P MBSPP P 1-1/ /4-11 H 1 FLANGE CODE 61, STRAIGHT 400-MBSPP P 3/ / MBSPP P MBSPP P 1-1/ /4-11 B A A B C Thread 200-CD P 3/ /4 - Code CD P Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P Code 61 C 400-CD P 3/ /4 - Code CD P 3/ Code CD P Code CD P /4 - Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P 1-1/ /2 - Code CD P 1-1/ Code CD P Code Phone: Fax:
25 FLANGE CODE 61, 45 B A A B C Thread 200-CD P 3/ /4 - Code CD P Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P Code 61 C 400-CD P 3/ /4 - Code CD P 3/ Code CD P Code CD P /4 - Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P 1-1/ /2 - Code CD P 1-1/ Code CD P Code 61 FLANGE CODE 61, 90 B A A B C Thread 200-CD P 3/ /4 - Code CD P Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P Code 61 C 400-CD P 3/ /4 - Code CD P 3/ Code CD P Code CD P /4 - Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P 1-1/ /2 - Code CD P 1-1/ Code CD P Code 61 Phone: Fax:
26 FLANGE CODE 62, STRAIGHT C B A A B C Thread 200-CD P 3/ /4 - Code CD P Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P Code CD P 3/ /4 - Code CD P 3/ Code CD P Code CD P /4 - Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P 1-1/ /2 - Code CD P 1-1/ Code CD P Code CD P 3/ /4 - Code CD P Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P Code 62 FLANGE CODE 62, 45 B A A B C Thread 200-CD P 3/ /4 - Code CD P Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P Code 62 C 400-CD P 3/ /4 - Code CD P 3/ Code CD P Code CD P /4 - Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P 1-1/ /2 - Code CD P 1-1/ Code CD P Code Phone: Fax:
27 FLANGE CODE 62, 45 Continued... B A A B C Thread 600-CD P 3/ /4 - Code CD P Code CD P 1-1/ /4 - Code 62 C 600-CD P 1-1/ /2 - Code CD P Code 62 FLANGE CODE 62, 90 A B C Thread 200-CD P 3/ /4 - Code CD P Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code 62 B A 200-CD P Code CD P 3/ /4 - Code CD P 3/ Code CD P Code CD P /4 - Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code 62 C 400-CD P 1-1/ /2 - Code CD P 1-1/ Code CD P Code CD P 3/ /4 - Code CD P Code CD P 1-1/ /4 - Code CD P 1-1/ /2 - Code CD P Code 62 Phone: Fax:
28 Interlock 2-Piece Fittings 800 Series 28 Phone: Fax:
29 Interlock 2-Piece Fittings Series FEMALE JIC SWIVEL, STRAIGHT H 1 A A H1 Thread 800-IL-FJX P 3/ / IL-FJX P / IL-FJX P 1-1/ / IL-FJX P 1-1/ / IL-FJX P /2-12 FEMALE BSP SWIVEL, STRAIGHT H 1 A A H1 Thread 800-IL-FJX P 3/ / IL-FJX P IL-FJX P 1-1/ / IL-FJX P 1-1/ / IL-FJX P INTERLOCK CODE 62, STRAIGHT B A A B Thread 800-IL-CD P 3/ /4 - Code IL-CD P Code IL-CD P 1-1/ /4 - Code IL-CD P 1-1/ /2 - Code IL-CD P Code 62 INTERLOCK CODE 62, 45 A A B C Thread 800-IL-CD P 3/ /4 - Code 62 B C 800-IL-CD P Code IL-CD P 1-1/ /4 - Code IL-CD P 1-1/ /2 - Code IL-CD P Code 62 Phone: Fax:
30 INTERLOCK CODE 62, 90 A A B C Thread 800-IL-CD P 3/ /4 - Code 62 C 800-IL-CD P Code IL-CD P 1-1/ /4 - Code 62 B 800-IL-CD P 1-1/ /2 - Code IL-CD P Code 62 INTERLOCK FERRULE 4-WIRE A A B Thread 800-IL-F4-12-2P 3/ Ferrule B 800-IL-F4-16-2P Ferrule 800-IL-F4-20-2P 1-1/ Ferrule 800-IL-F4-24-2P 1-1/2 Ferrule 800-IL-F4-32-2P 2 Ferrule INTERLOCK FERRULE 6-WIRE A A B Thread 800-IL-F6-16-2P 1 Ferrule B 800-IL-F6-20-2P 1-1/4 Ferrule 800-IL-F6-24-2P 1-1/ Ferrule 800-IL-F6-32-2P Ferrule 30 Phone: Fax:
31 High and Fittings Phone: Fax:
32 High and Fittings VHP 10,000 Inner Tube: Polyester elastomer Reinforcement: Up to three braids of aramid fiber plus one braid of steel wire Cover: Polyurethane-black-non pinpricked- white inkjet branding Temperature: -40 F / +212 F Application: Off-shore and sub-sea high pressure systems, Pumps and valves, Bolt tensioning tools, Jacking and rerailing equipment Key Note: 4 to 1 Safety Factor I.D. O.D. Max Working Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Couplings VHP ,000 40, VHP Colors Available : Black VHP 10,000 TWIN Inner Tube: Polyester elastomer Reinforcement: One or two braids of aramid fiber plus one braid of steel wire Cover: Polyurethane-black-non pinpricked- white inkjet branding Temperature: -40 F / +212 F Application: Rescue and safety equipment, High pressure systems and pumps, Bolt tensioning tools, Jacking and rerailing equipment Key Note: 4 to 1 Safety Factor I.D. O.D. Max Working Burst Bend Radius Weight Termination (mm) (psi) (psi) (mm) (lbs/ft) Couplings VHP / ,000 40, VHP Colors Available : Black, Red and Yellow 32 Phone: Fax:
33 VHP Male NPT VHP-NPT /4 1/4 Male NPT VHP-NPT /4 3/8 Male NPT F VHP Female Rigid NPT VHP-FNPT /4 1/4 Female NPT VHP-FNPT /4 3/8 Female NPT F VHP Male BSPP VHP-MBSPP /4 1/4 Male BSPP VHP-MBSPP /4 3/8 Male BSPP F Phone: Fax:
34 Type M F Material VHP-M9FX-04 1/4 Carbon Steel 9/16 Type M VHP-M9FX-04-SS 1/4 Stainless Steel 9/16 Type M F VHP Ferrule Material L C D VHP-Ferrule-04 1/4 Carbon Steel VHP-Ferrule-04-SS 1/4 Stainless Steel VHP Bend Restrictor L C D VHP-BR / Phone: Fax:
35 Chemical Compatibility Notes on chemical compatibility table: The following data is based on tests and believed to be reliable; However the tabulation should be used as a guide only, since it does not take into consideration all variables, such as elevated temperatures, fluid contamination, concentration, etc. that may be encountered in actual use. All critical applications should be tested. Key: E- Excellent - The fluid has a minimum or absent effect G- Good - The fluid has a weak or moderate effect X - Unsatisfactory - The fluid has a serious effect Chemical Product Polyester SBR EPDM Acetaldehyde - X Acetic Acid, 10% E G Acetone G C Acetylene E E Ammonia 10% - - Ammonium Carbonate, 10% - E Ammonium Chloride, 10% E E Ammonium Hydroxide - X Ammonium Sulfate G E Amyl Acetate G X Amyl Alcohol E E Aniline X X Antimony Chloride, 10% - X Astm Fuel A E X Astm Fuel B E X Astm Fuel C G X Astm Oil N. 1 E X Astm Oil N. 3 E X Atrazine E - Barium Chloride, 10% - E Barium Sulfate, 10% - E Beer E E Chemical Product Polyester SBR EPDM Benzene G X Benzoic Acid, 10% - X Borax Solutions E G Boric Acid, 10% E E Bromine (Anhydrous) X - Bromine Water, 25% - - Butane E X Butyric Acid, 10% - - Butyl Acetate G X Butyl Alcohol - - Calcium Chloride, 5% E E Calcium Hypochlorite, 5% E G Calcium Thiocyanate - - Carbon Dioxide E E Carbon Disulfide G X Carbon Monoxide E G Carbon Tetrachloride G X Carbonic Acid, 10% E E Chlorine (Dry) X - Chlorine (Wet) X - Chloroacetic Acid, 10% X X Chlorobenzene X X Chloroform X X Chlorosulfonic Acid X X Chromic Acid, 10% X - Citric Acid Solutions E E Copper Chloride, 10% E E Copper Cyanide - E Copper Sulfate Solutions E E Cottonseed Oil E X Cresol - X Cychlohexane E X Dibutyl Phthalate E X Diethyl Sebacate E X Dioctyl Phthalate E X Ethanolamine - G Ethyl Acetate G X Ethyl Alcohol E E Ethylene Chloride X X Ethylene Glycol E E Ethylene Oxide E X Ferric Chloride Solutions - E Fluorine X X Phone: Fax:
36 Chemical Product Polyester SBR EPDM Formaldehyde, 40% G E Formic Acid G E Freon R 407C E - Freon R 134a E - Gasoline G X Glycerin E E Glycolic Acid - - Hexane E X Hydrazine X - Hydrochloric Acid, 10% G X Hydrogen E G Hydrogen Peroxide, 5% - - Hydrogen Sulfide, 5% E X Isooctane E - Isopropyl Alcohol E E Lactic Acid, 10% - cold - G Linseed Oil E X Mercury E E Methyl Alcohol E E Methyl Chloride X - Methyl Ethyl Ketone G - Methylene Chloride X - Mineral Oil E X Naptha E X Napthalene G X Nitric Acid, 10% G X Nitric Acid, 30% X X Nitrobenzene X X Nitromethane - G Oil Fiat Tutela Lhm E - Oil Kluber Summit Hy Syn E - Oil Panolin 9632 E - Oil Panolin Hlp Synth E - Oil Pentosin Super Dot Oleic Acid E X Oleum, 20-25% X X Palmitic Acid E X Percholirc Acid, 10% - X Perchloroethylene X X Petrol G X Phenol X X Chemical Product Polyester SBR EPDM Phosphoric Acid (10%) E Phosphoric Acid, 50% - G Potassium Carbonate, 20% - E Potassium Chloride, 90% - E Potassium Hydroxide, (10%) G G Potassium Permanganate, 5% X - Potassium Thiocyanate - - Pydraul 312 E X Sea Water E E Shell Brake Fluid Dot4 - E Silicone Oils E E Skydrol 500B E - Soap Solution E E Sodium Acetate, 60% - X Sodium Bicarbonate - E Sodium Carbonate - E Sodium Chloride, 10% E E Sodium Hydroxide, 10% E G Sodium Hydroxide, 20% E G Sodium Hydroxide, 50% G G Sodium Hypolchlorite, 5% E X Sodium Nitrate, 5% - E Sodium Sulfate, 90% - E Sodium Sulfide - E Steam (100 C) X X Sulfur Dioxide - C Sulfuric Acid > 50% X X Sulfuric Acid, 10% E X Sulfuric Acid, 20-50% E X Sulfurous Acid, 10% G G Tannic Acid, 10% E F Tetrafluoro Propane - - Tetrahydrofuran G - Toluene G X Trichloroethylene X X Triethanolamine X - Trisodium Phosphate E E Water E F Xylene G X Zinc Chloride, 10% E E 36 Phone: Fax:
Selection of DODGE E-Z KLEEN Polymer and Stainless Steel Housed Ball Bearings. P = (X x F R ) + (Y x F A ) F A C o
Selection of DODGE and Stainless Steel Housed Ball Bearings DODGE ball bearings are primarily designed for radial loading. However, they have the capacity to carry thrust loads and combined radial/thrust
More informationApplication Data Sheet. Chemical Compatibility Chart. IND-AS EN-01 (May, 2014) Metals Plastics Seals KEY. Good. Fair. Ethylene Propylene.
Chemical Compatibility Chart 6 Stainless Acetic Acid Acetone Acetylene Acidic Mine Water Acrylonitrile Ammonium Chloride Ammonium Hydroxide Ammonium Sulfate Ammonium Thio-Sulfate Anhydrous Ammonia Anhydrous
More informationHow to Use the Chemical Compatibility Chart. Vials and Closures >> Chemical Compatibility Chart
How to Use the Chemical Compatibility Chart The following chart contains information regarding the expected effects of 7 day direct solvent exposure on materials used for production of vials, caps and
More informationFR PVC COATED RAINWEAR
FR COATED RAINWEAR INDUSTRY/FORESTRY/RAINWEAR All fabrics are tested and certified in accordance with en 343; the european standard for waterproof clothing. Extreme weather protection - EN 343 Protection
More informationSwivel Joints Flexmaster Joints Part Number NH NH NH NH NH NK NK
FLUID CONVEYING PRODUCTS Section Pages Hose 15-67 Fittings 68-180 Adapters and Tube Fittings 181-228 Description Page Features 246, 247 Technical Data 248, 253 Gasket Selector Chart 249 How to Order 250
More informationIssue One. Chemical Compatibility Guide
Issue One Chemical Compatibility Guide Chemical Compatibility Guide Fluolion 200, 700, 800, 900 modified PTFE sheet gasket materials The following information is issued as a guide only. All media are taken
More informationHigh pressure industrial ball valves
High pressure industrial ball valves High pressure industrial ball valves Applications Legris high pressure ball valves are suited for a wide range of industrial applications. They are designed both for
More informationReplacement Tubes for Gillian Gas Detection Pumps
236SA S 1,1,2-Trichloroethane (10-100 ppm) 235SA S 1,1-Dichloroethane (10-160 ppm) 230SA S 1,2-Dichloroethane (5-50 ppm) 145SA S 1,2-Dichloroethylene (4.2-840 ppm) 194S S 1,3-Dichloropropane (10-500 ppm)
More informationPhysical properties of PET resins. 1. Intrinsic Viscosity (IV)
Physical properties of PET resins 1. Intrinsic Viscosity (IV) Intrinsic viscosity (IV) is a measure of polymer molecular weight, which in turn is a measure of the mechanical strength capability of the
More informationKLINGER KGS. Rubber-Metal-Gaskets Safe sealing of gases and liquids
Rubber-Metal-Gaskets Safe sealing of gases and liquids Rubber-metal-gaskets are used where safe sealing of conventional up to special industrial media such as gases and liquids are required under usual
More informationSmall on price, big on boot
018 VOLUME 1 FEATURES KEY Toe Cap High Heat Non Conductive Female Male Leather Chemical Body International Organization for Standardisation Body PU - Polyurethane RECOMMENDED INDUSTRY USE* General Smelting/
More informationKLINGER-KGS Rubber- Metal-Gasket
Rubber- Metal-Gasket Where safe sealing of water, air, acids, alkalines and hydrocarbons is required at low forces and low temperatures, KLINGER-KGS is an interesting solution. Suitable for flanges made
More informationDynaform Fiberglass Structural Shapes. Design Guide. High Performance Composite Solutions. Corrosion Resistant. Fire Retardant.
Design Guide Dynaform Fiberglass Structural Shapes Corrosion Resistant Fire Retardant Low Maintenance Light Weight Long Service Life High Performance Composite Solutions Q U A L I T Y ISO 9001-2000 C E
More informationKLINGER top-chem A milestone in PTFE gasketing KLINGERsoft-chem
KLINGER top-chem A milestone in PTFE gasketing KLINGERsoft-chem Top Quality PTFE-based materials for every application KLINGER The global leader in static sealing KLINGER top-chem 2000: Universal gasket
More informationP17 Tempra Pro plugs, mobile sockets, fixed sockets, surface mounting sockets and appliance inlets - IP 66/67-63 A A
CONTENTS Page 5 555 09 5 555 29 5 555 59 5 555 9 1. General characteristics...1 2. Use...1 3. Range/Equivalence table...2 4. Dimensions..............................3 5. Technical characteristics...5 6.
More informationStrength, resilience, rigidity - these are all attributes needed to combat arduous and aggressive conditions. Tufflite has them all.
Strength, resilience, rigidity - these are all attributes needed to combat arduous and aggressive conditions. Tufflite has them all. From commercial applications requiring a simple sealed luminaire, right
More informationMetallic Systems TYPE SPTC
CONDUIT 27/01/2009 Technical Data Sheet Page No. 1 Applications Hospitals External Safety Critical Area Fittings IP54 SPB Fittings type A & B Characteristics Very High UV Resistance High Flexibility Medium
More informationJ-FLEX HYDRAULIC HOSE SOLUTIONS
Your Hose & Fitting Connection J-FLEX HYDRAULIC HOSE SOLUTIONS ww.jgbhose.com JGB Headquarters 115 Metropolitan Dr. Liverpool, NY 13088 (315) 451-2770 Buffalo Branch 2540 Walden Ave. Cheektowaga, NY 14225
More informationHYDRAULIC HOSES. FlexIT 015
HYDRAUIC HOSES 015 HYDRAUIC HOSES 015 Intertraco (Italia) S.p.A. lexible Hoses Catalogue - SIHX150 - April 2015 The data reported in this catalogue are not binding. Intertraco (Italia) S.p.A. reserves
More informationNO: AC.2006.CT.01 شرکت کامپوزیت آسیاآسیا(سهامی تولیدکننده انواع قطعات کامپوزیتی گریتینگ و سینی کابل)
NO: AC.2006.CT.01 خاص) شرکت کامپوزیت آسیاآسیا(سهامی تولیدکننده انواع قطعات کامپوزیتی گریتینگ و سینی کابل) (پروفیل FRP SPECIFICATIONS OF PULTRUDED LADDER-TYPE CABLE TRAYS E- mail:info@asiacomposite.comww
More informationQUALITY HYDRAULIC PRODUCTS
QUALITY HYDRAULIC PRODUCTS N.R.P. ISO9001 Certified Quality System NRP- JONES Has What it Takes to Build Your Business! Over a half-century of experience helps you build customer satisfaction while increasing
More informationColorimetric Gas Detector Tube System US Dollar Price List
Colorimetric Gas Detector Tube System US Dollar Price List Sensidyne, LP - Gas Detector Tube Price List Effective Date: February 12, 2012 Rev. A 010612 Table of Contents Gas Detection Pump Kit & Accessories
More informationInformation. Mechanical. Electrical. Chemical. Conversions & Calculations
i Information Installation Monitoring Repair As part of our fluidity.nonstop concept, AxFlow has become one of the leading UK providers of pump care services. We have Pump Service Centres spread across
More informationCONNECTION BULLETIN. Vogt Valves. Experience In Motion. Zero Leakage Forged Steel Check Valves Class 800. FCD VVABR /04 (Replaces CB-03)
CONNECTION BULLETIN Vogt Valves Zero Leakage Forged Steel Check Valves Class 800 FCD VVABR1003-00 10/04 (Replaces CB-03) Experience In Motion Zero Leakage, Forged Steel Check Valves: Class 800 Vogt Series
More informationSETUP, OPERATING AND MAINTENANCE INSTRUCTIONS FOR PNEUMATIC CHEMICAL INJECTORS, SNAP ACTION RELAYS AND TIMERS
SETUP, OPERATING AND MAINTENANCE INSTRUCTIONS FOR PNEUMATIC CHEMICAL INJECTORS, SNAP ACTION RELAYS AND TIMERS 28103 Ave. Stanford / Valencia, CA 91355 (661) 257-3022 - (800) 421-8910 - FAX (661) 257-3385
More informationThe Air Logic Division of Fred Knapp
Introduction to Air Logic The Air Logic Division of Fred Knapp Engraving Company designs and manufactures a comprehensive line of pneumatic and vacuum control equipment. Air Logic has earned a reputation
More informationKLINGER KGS Rubber- Metal-Gasket
KLINGER KGS Rubber- Metal-Gasket Where safe sealing of water, air, acids, alkalines and hydrocarbons is required at low forces and low temperatures, KLINGER KGS is an interesting solution. Suitable for
More informationGeneral applications Chemical plant, oil refinery, power plant, steam, Dowtherm, fused alkali, fuel oil and gas
KTM Gratite Seat i-temp Ball Valves KTM KTM s Gratite seat ball valve not only operates across an impressive range of temperatures, from -29 C to 500 C, it also boasts outstanding performance and a reliability,
More informationHYPRA Prisinter 16/32/63 A
8704 LIMOGES Cedex Telephone: + 33 0 06 87 87 - Fax: + 33 0 06 88 88 HYPR Prisinter 16/32/63 Page 1. General characteristics........1 2. Range......................1 3. Dimensions............... 2-3 4.
More informationSingle Wire Smooth Cover Double Wire Smooth Cover Extra Pressure Double Wire Wrapped Cover
SECTION 1 SAE100R1 Page 6 SAE100R2 Page 6 SAE100R2XP Page 7 SAE100R2GP Page 7 Quick Reference Taipan Hose Single Wire Smooth Cover Double Wire Smooth Cover Extra Pressure Double Wire Wrapped Cover SAE100R2H
More informationTANK LINING RESISTANCE GUIDE I-19
INTRODUCTION Wattyl s Tank Lining Resistance Guide provides a list of chemicals and their suitability in contact with Epinamel TL710, Galvit ES600 and Galvit ES510. GUIDE TO DATA R Recommended cargo R,
More informationWe offer two fire retardant (FR) resins for strut systems: polyester and vinyl ester. Both resins are ideal for corrosive environments.
Materials We offer two fire retardant (FR) resins for strut systems: polyester and vinyl ester. Both resins are ideal for corrosive environments. While polyester is sufficient for most uses, vinyl ester
More informationThe Most Trusted Casters IN THE WORLD www.colsoncaster.com Download 3D CAD Models and Data Sheets (See back cover) www.colsoncaster.com 800-643-5515 Designed, tested and proven for over 130 years. Since
More informationThe Industrial Choice. Model TFBD. Model FBD FIBERGLASS AXIAL FLOW FANS. Model FDP / FRV / FBD / TFBD / VTFBD
The Industrial Choice. Model TFBD Model FBD FIBERGLASS AXIAL FLOW S Model FDP / FRV / FBD / TFBD / VTFBD CATALOG 85 October 207 Fiberglass Axial Flow Fans Models FDP FRV FBD TFBD VTFBD Medium Pressure
More informationCatalog June Mounted Bearings
Catalog June 2014 Mounted Bearings Contents. Ultra Kleen Features/Benefits.... 1-3 How to order/nomenclature............................................. 1-6 Easy Selection.... 1-7..................................................
More informationChemical Resistance Chart
Acetaldehyde 0 Acetic Acid @ 20 C 5 0 Acetic Acid @ 20 C 10 0 Acetic Acid @ 60 C 10 0 Acetic Acid @ 20 C 20 0 Acetic Acid @ 20 C 30 0 Acetic Acid @ 60 C 30 0 Acetic Anhydride 0 Acetone 0 Acetonitrile 0
More informationThe Most Trusted Casters IN THE WORLD.
The Most Trusted Casters IN THE WORLD www.colsoncaster.com The following catalog is brought to you by Visit us online at cplauman.com to view our wide selection of casters, wheels, hand trucks, & cargo
More informationFRP RADIAL FUME EXHAUSTERS/ PRESSURE BLOWERS THE NEW YORK BLOWER COMPANY
FRP BULLETIN 58 DECEMBER, 2005 RADIAL FUME EXHAUSTERS/ PRESSURE BLOWERS Fiberglass-reinforced-plastic fans for handling corrosive gas streams in a wide variety of process applications... FRP RADIAL FUME
More informationQ-Duct wiring duct. Q-Duct Wiring duct. Catalog number explanation QD 100 X 100 S G
Q-Duct Wiring duct Wire duct, ties, Q-Duct wiring duct General information ABB offers Q-Duct, a wide variety of wire duct and accessories. Wire duct bases are available in six nominal widths - 1/2" to
More informationFILTRATION SYSTEMS CARBOX PHARMACEUTICAL HOODS ACTIVATED CHARCOAL FILTERS
CARBOX FILTRATION SYSTEMS 47 Filtration systems for the treatment of harmful fumes resulting from chemical processings. INDEX PHARMACEUTICAL HOODS 49 ACTIVATED CHARCOAL FILTERS 53 48 CAP-FARM 60 Aspirated
More informationCeilcote Corrosion Resistant Guide
Ceilcote Corrosion Resistant Guide Monolithic Linings Monolithic Flooring Heavy-Duty Coatings Polymer Grouts Adhesives & Joint Fillers JULY 2012 INTRODUCTION Over 340 corrosive environments are classified
More informationO BRIEN BRASS COMPANY
O BRIEN BRASS COMPANY Table of Contents Quality................................2 Threads...............................3 Hose & Coupling Compatibility.............4 SAE 100R1, SAE 100R2...................5
More informationPTFE Gasket Materials
PTFE Gasket Materials KLINGERtop-chem Top Quality Reinforced Thermoseal soft-chem Expanded Sealex Joint Sealant Sealing Solutions for the Chemical Process Industry. ISO 9001:2000 A Long-standing Tradition
More informationWelcome to JDM Industrial Maintenance Inc.
Welcome to JDM Industrial Maintenance Inc. We are an experienced and innovative company which has been serving the City of Peterborough and the surrounding areas since 98. Our diverse skills and resources
More informationSection 3 - Chemical/Environmental Resistance Part 1 - XR-5 Fluid Resistance Guidelines
Section 3 - Chemical/Environmental Resistance Part 1 - XR-5 Fluid Resistance Guidelines The data below is the result of laboratory tests and is intended to serve only as a guide. No performance warranty
More informationTECHNICAL MANUAL COMPRESSION FITTINGS
TECHNICAL MANUAL COMPRESSION FITTINGS Elysee Join the Professionals! The professional s choice for complete solutions in piping systems. Best value for money. Top quality at competitive prices One- stop
More informationright product for your application.
AUG 2010 8 7 6 5 4 The possibilities are endless with Eagle Polyurethane & Polyester Belting and O-Rings from Fenner Drives. As a world leader in belting, we have a comprehensive range of high quality
More informationSUPERLIT GRP PIPE & FITTINGS AS AS GLASS REINFORCED POLYESTER (GRP) PIPELINE SYSTEM VERSION 1.0
SUPERLIT GRP PIPE & FITTINGS AS3571.1 AS3571.2 GLASS REINFORCED POLYESTER (GRP) PIPELINE SYSTEM VERSION 1.0 The products shown form part of our continuous improvement program and as such the product designs,
More informationTEST REPORT: CHM12-01-LSM
Date: Tel: +65 68851335 Fax: +65 67784301 Client s Ref: QM-0112-056 Email: Sihai.LI@tuv-sud-psb.sg Note: This report is issued subject to the Testing and Certification Regulations of the TÜV SÜD Group
More informationInstruction Manual BL1.5 BL3 BL5 BL7 BL10 BL15 BL20. Dosing Pumps.
Instruction Manual BL1.5 BL3 BL5 BL7 BL10 BL15 BL20 Dosing Pumps www.hannainst.com Dear Customer, Thank you for choosing a Hanna product. Please read this instruction manual carefully before using the
More informationChemical Resistance of Arnitel
Chemical Resistance of Arnitel Chemical resistance of any material is a function of the interactions that occur between the polymer and a chemical in contact. The chemical resistance or the lack of it
More informationDucting & Ventilation Components
Ducting & Ventilation Components 111 Powell Road Independence, MO 64056 visit www.hemcocorp.com Phone: 816-796-2900 Fax : 816-796-3333 E-Mail : info@hemcocorp.com Exhaust Blowers are constructed of chemical
More informationSwivel Joints Flexmaster Joints BD BD BD BD BD BD
FLUID CONVEYING PRODUCTS Section Pages Hose 15-67 Fittings 68-180 Adapters and Tube Fittings 181-228 Description Page How to Order 230 Selection Criteria 231 Selection Chart 232 Fluid Compatibility Chart
More informationThis catalogue has been designed to provide a complete guide to our hydraulic hoses and offer useful technical data for the product range.
HOSES CATALOGUE Introduction This catalogue has been designed to provide a complete guide to our hydraulic hoses and offer useful technical data for the product range. The hydraulic hoses shown in this
More informationP17 plugs, mobile sockets and surface-mounting sockets «New range 16 and 32 A»
87045 LIMOGES Cedex Telephone : + 33 0 5 55 06 87 87 - Fax : + 33 0 5 55 06 88 88 P7 plugs, mobile and surface- Cat. Nos. : 555 53/57/58/73/77/78-5 53/57/58/73/77/78 CONTENTS Page 575 4. Definition....
More informationSafety Products brochure 11 Int INDEX. Exhaust Filters 2. Air Inlet Valve 5. GL45 Caps 6. DIN50 Caps 8. GL38 Caps 10. DIN60 Caps 11.
INDEX Safety Products brochure 11 Int Exhaust Filters 2 Air Inlet Valve 5 GL45 Caps 6 DIN50 Caps 8 GL38 Caps 10 DIN60 Caps 11 S51 / S61 Caps 12 B53 / B83 / GL80 Caps 13 Chemical Resistance chart 14 VICI
More informationTECHNICAL DATASHEET. Weatherproof LED luminaire ZALEDA EVOL II. 85,000 h product life. General characteristics. Mounting accessories.
85,000 h product life Frequency 0 50/60Hz PMMA 650 ºC IK03 Rated voltage 220 240V PC 850 ºC IK08 +45 C -30 C ZALEDA EVOL G2 6000-840 ET PC General characteristics New weatherproof LED lighting generation
More informationP17 combined units LIMOGES Cedex Telephone : Fax : Cat. No.(s) : 566 XX XX XX XX
8704 LIMOGES Cedex Telephone : + 33 0 06 87 87 - Fax : + 33 0 06 88 88 P17 combined units Cat. No.(s) : 66 XX - 72 XX - 77 XX - 89 XX CONTENTS Page 1. Description...1 2. Use...1 3. Range.......................
More informationSafety Products brochure 11 Int INDEX. Exhaust Filters 2. Air Inlet Valve 5. GL45 Caps 6. DIN50 Caps 8. GL38 Caps 10. DIN60 Caps 11.
INDEX Safety Products brochure 11 Int Exhaust Filters 2 Air Inlet Valve 5 GL45 Caps 6 DIN50 Caps 8 GL38 Caps 10 DIN60 Caps 11 S51 / S61 Caps 12 B53 / B83 / GL80 Caps 13 Chemical Resistance chart 14 VICI
More informationDead Level. Pre-sloped Trench Drain System. Watts.com
Dead Level Pre-sloped Trench Drain System Watts.com Dead Level Pre-sloped Trench Drain Simple. Straight. Stable. The Dead Level Trench Drain is uniquely designed to install and perform like no other trench
More informationTECHNICAL DATASHEET. Weatherproof LED luminaire DUNA FLEX High Efficiency. 70,000 h product life IK C. Applications recommendation
70,000 h product life Frequency 0 50/60Hz 650 C IK 03 Rated voltage 220 240V +35 C -25 C DHE 1.2 41-840 ET SMC DPM IX CG General characteristics Applications recommendation LED module luminaire manufactured
More informationAssembly and Supply of:
CATALOGUE Inflex Hydraulic Engines & Machinery Spare Parts Trdg llc P.O.Box 392755, Dubai - UAE, Tel: 04 3394677, Fax: 04 3394388 Email: info@inflexhydraulics.com, www.inflexhydraulics.com www.stainlesssteelhosesdubai.com
More informationFAX: HYDRAULIC HOSE FITTINGS AND ADAPTERS
C1T 1-Wire Braid Hose SAE 100R1 Type AT Recommended for: Medium pressure hydraulic lines. Meets or exceeds the requirements of SAE 100R1AT and performance requirements of DIN 20022 1SN. Tube: Black, oil-resistant
More informationGS-HYDRO GATES HOSES & CARBON STEEL COUPLINGS
GS-HYDRO GATES HOSES & CARBON STEEL COUPLINGS General Information GS-Hydro supplies a comprehensive selection of hoses and hose couplings which includes BSP, NPT, JIC, Metric, SAE 3000/6000 Flanges and
More informationFiberglass Centrifugal Exhausters. Series 82 Series 83 Series 87 Series 88 HARTZELL. Hartzell Fan, Inc., Piqua, Ohio
Fiberglass Centrifugal Exhausters Series 82 Series 83 Series 87 Series 88 BUILT WITH HONOR HARTZELL FAN, INC PIQUA, OHIO USA HARTZELL Hartzell, Inc., Piqua, Ohio 45356 November 2007 Index Hartzell Model
More informationTECHNICAL DATASHEET. Weatherproof LED luminaire DUNA FLEX Standard Plus. 50,000 h product life IK C. Applications recommendation
TECHNICAL DATASHEET IK 08 Frequency 0 50/60Hz Rated voltage 220 240V 850 C 50,000 h product life +35 C -25 C DSTP 1.2 40-840 ET PC DPC PA General characteristics Applications recommendation LED module
More informationTUBING. Polyurethane Polyethylene LLDPE Nylon 12 PTFE FEP PVC
TUBING Polyurethane Polyethylene LLDPE Nylon 12 PTFE FEP PVC September 2003 Polyurethane ATP polyurethane tubing is made from the highest quality raw materials available. It is ether-based to provide excellent
More informationMM PISTON PUMP
MM-76500-50 PUMP NATIONAL INSTRUMENT COMPANY Part No. 8649, FSV-60-1 with O-Ring Piston Note: To be used only on the MM-76400-20 and MM-76400-25 Fillers For filling semi viscous** to heavy viscosity***
More informationUniflex is the first in India to manufacture hose assemblies using pallet swage fittings.
Universal Flexibles Pvt. Ltd. is involved in the manufacture of top of the line quality Hydraulic Assemblies having commenced operations at Bangalore in 1987. Tradition of excellence Uniflex is the first
More informationSERIE 2T SERIES 3T ASTM - A216 WCB, A216WCC, A351 CF8, A351 CF8M, A352 LCB, A351 CN7M, A105N, NO. Part Name Material
3 SERIE 2T SERIES 3T NO. Part Name Material 1 Body 2 Body Adaptor 3 Ball 4 Stem 5 Seat Retainers 5a Seat Inserts 6 O-Ring ASTM - A216 WCB, A216WCC, A351 CF8, A351 CF8M, A352 LCB, A351 CN7M, A105N, A182
More informationThe Stability of Sulfur Compounds, Low Molecular Weight Gases, and VOCs in Four Air Sample Bag Materials
The Stability of Sulfur s, Low Molecular Weight Gases, and VOCs in Four Air Sample Bag Materials Linda Coyne Cindy Kuhlman Nicole Zovack SKC Inc. Eighty Four, PA 15330 25 January 2011 Publication 1805
More information90 Dual Plane Swivels Switch Your Swivel!
90 Dual Plane Swivels Switch Your Swivel! HOW TO ODE STEM BODY OPTIONS 9 SS 8 FP 50 X FP 50 Z - V SS-SINGLE PLANE DP- DUAL PLANE SEIES (THOUGH HOLE) THEAD SIZE MULTIPLES OF 100 FO N.P.T.F. MULTIPLES OF
More informationQUICK DISCONNECT COUPLINGS
FLUID CONVEYING PRODUCTS Serving your industry with quality fluid conveying products Construction Forestry Public Safety Utility Marine and Defense Oil and Gas Transportation Steel Machine Tool 268 RETURN
More informationQuick Disconnect Couplings
Quick Disconnect Couplings Serving your industry with quality fluid conveying products Construction Forestry Public Safety Utility Marine and Defense Oil and Gas Transportation Steel Machine Tool FLUID
More informationHigh-Strength Steel Reinforced HDPE Pipe. For pipe specifications, please visit:
Kanaflex Steel Reinforced Pipe (SRPE) Kanapipe for Storm and Sanitary Sewer Applications-12"-72" Kanaflex Steel Reinforced Pipe (SRPE) is the sound solution for storm drainage, combined sewer overflow,
More informationINTRODUCTION OF KOMAN
H Y D R A U L I C INTRODUCTION OF KOMAN KOMAN HYDRAULIC 02 03 시대는변해도, 기업환경은달라도 NO.1 비즈니스파트너, Koman 입니다 코만은 1981년회사설립이래, 오랫동안축척된기술과신뢰를바탕으로, 정밀한품질관리체제에서유압용호스및호스피팅과어댑터를 SAE, DIN, JIC 및 JIS 등의국제규격을통해생산하고있으며,
More informationNew Pig One Pork Avenue Tipton, PA Chemical Compatibility Guide for: FTI Pumps
Chemical Compatibility Guide for: FTI Pumps The guide on the following page(s) was provided by the supplier. New Pig Corporation assumes no responsibility, obligation, or liability in conjunction with
More informationANALYTICAL RESULTS. PWS ID/Name: ROCKHOUSE MOUNTAIN - CONWAY Report Date: 03/29/2016
10014605 Analyzing Lab: 1012-EASTERN ANALYTICAL INC ANTIMONY, TOTAL ND MG/L.001 1 03/18/2016 ARSENIC, TOTAL 0.002 MG/L.001 1 03/18/2016 BARIUM, TOTAL 0.005 MG/L.001 1 03/18/2016 BERYLLIUM, TOTAL ND MG/L.001
More informationProduct Information S/PA
Description Tico S is a high performance machinery mounting material. It matches today s fast changing manufacturing environment, where ease of machine mounting and flexibility of plant layout are prime
More informationMarina Cabinets LIMOGES Cedex Telephone: Fax:
87045 LIMOGES Cedex Telephone: 0 5 55 06 87 87 - Fax: 0 5 55 06 88 88 Marina s CONTENTS Page 1. Main characteristics...1 2. Range....1 3. Technical characteristics...1 4. Dimensions....3 5. Equipments...4
More informationSection Fume Hoods Specifications 6/1/14 LABORATORY FUME HOODS
1.01 SUMMARY A. Section Includes: Fume hoods LABORATORY FUME HOODS B. Related Sections 1. Division 12 Section - 12345 - Steel Laboratory Casework 2. Division 12 Section - 12346 - Agility Adaptable Furniture
More informationIntroduction AMCA SEAL TEXEL-SEIKOW USA.,
FTF BLOWER MODELS Introduction This catalog features Fiberglass Reinforced Plastic Centrifugal Fan, FTF models, which are suitable for use in the chemical, metal, wastewater, semiconductor, pharmaceutical,
More informationGS-HYDRO INTERTRACO HOSES & CARBON STEEL COUPLINGS
GS-HYDRO INTERTRACO HOSES & CARBON STEEL COUPLINGS PRODUCT CATALOGUE INTERTRACO HOSES & CARBON STEEL COUPLINGS General Information GS-Hydro supplies a comprehensive selection of hoses and hose couplings
More informationMM PISTON PUMP
MM-76500-30 PISTON PUMP NATIONAL INSTRUMENT COMPANY Part No. 8655, FKS-60-75 Pump with O-Ring Piston For filling free flowing* to semi viscous** liquids INSTRUCTIONS U.S. AND FOREIGN PATENTS ISSUED AND
More informationPolycarbonate & Laminate Half Trays
Polycarbonate & Laminate Half Trays Positioning pg. 8-47 Premium Transparent Half Trays (Viewline Plus) 3/8 thick break-resistant polycarbonate Heavy-duty moisture-resistant tray for institutional or long
More informationDelta Intercontinental Pte Ltd Tel : Fax: Woodlands Industrial Park E1, #
Impact, tear and abrasion resistant. Excellent corrosion protection. Low permeability. Fast reactivity and cure time with no catalysts. Applicable in temperatures from -30C to 70C. Almost immediate return-to-service
More informationModels 910, 911, 916, 917, 920, 921, 927 ASME Section VIII, Air/Gas/
Models 910, 911, 916, 917, 920, 921, 927 ASME Section VIII, Air/Gas/ Steam/Liquid, UV National Board Certified. Also available for Vacuum Service Model 921: Steel body and bonnet with plain lift lever
More information150 Series Brass Horizontal Float Valve. Technical Information
150 Series Brass Horizontal Float Valve Technical Information HORIZONTAL FLOAT VALVES Based on a simple yet effective operating principle, Philmac horizontal float valves are quick and easy to install
More informationEZ-View. Flow Meters ISO CERTIFIED 9001
EZ-View ISO CERTIFIED 9001 General Design Features OPERATING PRINCIPLE The EZ-View Flow Meter is a variable-area instrument. A precisionmolded, sharp-edged Orifice, located within the Piston Assembly,
More informationAPPLICATIONS Pollution Control Scrubbers Odor Control Fume Exhausting / Fume Hood
FTF BLOWER MODELS Introduction This catalog features Fiberglass Reinforced Plastic Centrifugal Fan, FTF models, which are suitable for use in the chemical, metal, wastewater, semiconductor, pharmaceutical,
More informationEF 8 EF 9. Company name Idemitsu Nippon Oil Cosmo Oil Showa Shell Sekiyu TonenGeneral Sekiyu Japan Energy
2 3 4 5 6 7 8 9 Company name Idemitsu Nippon Oil Cosmo Oil Showa Shell Sekiyu TonenGeneral Sekiyu Japan Energy Turbine oil P-32 Turbine oil 32 Turbine 32 Turbine oil 32 R turbine oil 32 Turbine oil 32
More informationBulletin JB27B Supersedes Bulletin JB27A. Quick Disconnect Couplings
Bulletin JB27B Supersedes Bulletin JB27A Quick Disconnect Couplings Serving your industry with quality fluid conveying products Construction Forestry Public Safety Utility Marine and Defense Oil and Gas
More informationCERTIFIED & TESTED TO ISO-22241
DEF HOSE TUBE Specially Formulated Polyurethane COVER Specially Formulated TPR APPLICATIONS DEF, AUS 32, oil, diesel FEATURES CERTIFIED & TESTED TO ISO-22241 Clean Certified DEF Assemblies Available. Lighter
More information05. YY XX. XX. series nominal size
Balflex MicroTest Check Line Hoses, Connectors & Gauges Balflex MicroTest is the range of hoses, couplings and gauges for check lines in hydraulic or refrigeration systems. Balflex MicroTest is produced
More informationFibreglass Reinforced Plastic
Fibreglass Reinforced Plastic Grating / Structural / Hand Rail Systems Won t Rust - Stronger than Steel ISO 2001 Certified Grating FRP Handrail Systems Certified to Australian Standards AS-1657-2013 We
More informationHOSE & HOSE PROTECTION
ALL YOU CAN EXPECT AND MORE Think about Hydraulics Differently Quality European Hose SECTION A HOSE INDEX 1 Hydraulic Hose HOSE & HOSE PROTECTION 1SN - SAE R1 AT - 1 Wire Thin Cover Hose 1SN - 1 Wire Thin
More informationHYDRAULIC HOSES. FlexIT 018
HYDRAULIC HOSES FlexIT 018 HYDRAULIC HOSES Flexit 018 Intertraco (Italia) S.p.A. Flexible Hoses Catalogue - GSIHFX180 - March 2018 The data reported in this catalogue are not binding. Intertraco (Italia)
More informationPressure switch FF 4 Approval acc. to ATEX EN For mining and chemistry
Approval acc. to ATEX EN 679 Description n... 3 bar with perbunan diaphragm. n 6... 5 bar with plastic plunger and throttle. n Throttle must be removed when using viscous media. 151 mm 7 13 mm a 1 mm,5
More informationVentureClad Insulation Jacketing Tapes 1577 Series
VentureClad Insulation Jacketing Tapes 1577 Series Technical Data August 2017 Product Description 3M VentureClad Insulation Jacketing System is a zero permeability, all weather, multi-layered laminate
More information221 S. Westgate Drive Carol Stream, IL FAX: AG-10/2. January 2014
221 S. Westgate Drive Carol Stream, IL 60188 630-752-0600 FAX: 630-752-0680 www.jasonindustrial.com AG-10/2 January 2014 TRUE-PREEM TPR SPRAYER HOSE TUBE/COLOR: TPR, Black REINFORCEMENT: Polyester Braid
More information