2. DISCONNECT BATTERY NEGATIVE TERMINAL (See page 60 1) 3. REMOVE SHIFT LEVER KNOB SUB ASSY 4. REMOVE SHIFT LEVER KNOB SUB ASSY
|
|
|
- Byron Parker
- 5 years ago
- Views:
Transcription
1 7112 INSTRUMENT PANEL/METER 710DV02 REPLACEMENT HINT: COMPONENTS: See page TABLE OF BOLT, SCREW AND NUT HINT: The bolts, screws and nuts, which are necessary for installation and removal of the instrument panel, are shown in the illustration below with alphabets. mm (in.) (L = Length) Code Shape Code Shape Code Shape <A> φ = 6 (0.24) <B> φ = 8 (0.31) L = 24 (0.94) φ = 6 (0.24) L = 20 (0.79) <D> φ = 6 (0.24) L = 16 (0.63) φ = 6 (0.24) L = 18 (0.71) <F> φ = 5 (0.20) L = 14 (0.55) φ = 5 (0.20) L = 16 (0.63) <H> φ = 5 (0.20) L = 18 (0.71) <I> φ = 5 (0.20) L = 14 (0.55) B DISCONNECT BATTERY NEGATIVE TERMINAL (See page 601) 3. REMOVE SHIFT LEVER KNOB SUBASSY 4. REMOVE SHIFT LEVER KNOB SUBASSY 5. REMOVE CONSOLE UPPER PANEL GARNISH NO.2 (a) Disengage the 3 clips and remove the console upper panel garnish No.2. 3 Clips B
2 INSTRUMENT PANEL/METER REMOVE CONSOLE UPPER PANEL GARNISH NO.1 (a) Disengage the 4 clips and remove the console upper panel garnish No.1. 4 Clips B REMOVE CONSOLE PANEL UPPER ASSY (a) Disengage the 11 clips and remove the console panel upper assy, then disconnect the connectors. 11 Clips B REMOVE INSTRUMENT PANEL GARNISH SUBASSY LH (a) Using a moulding remover, disengage the bottom 2 clips. (b) Using a moulding remover, disengage the top 2 clips. (c) While wiggling the center part, disengage the center 3 clips carefully. (d) Disconnect the connector and remove the instrument panel garnish subassy LH. B REMOVE INSTRUMENT PANEL GARNISH SUBASSY RH 10. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER LOWER (a) Disengage the 5 clips and remove the instrument cluster finish panel center lower, then disconnect the connectors. 5 Clips B REMOVE INTEGRATION CONTROL & PANEL ASSY (See page 5512) 3129
3 7114 INSTRUMENT PANEL/METER 12. REMOVE CONSOLE REAR END PANEL SUBASSY (a) Disengage the 2 clips and the 5 claws, and then remove the console rear end panel subassy. (b) Disconnect the connectors. 5 Claws B63455 <F> <D> <D> 13. REMOVE RR CONSOLE BOX ASSY (a) Remove the 2 bolts <D>, the 2 screws <F> and the RR console box assy. <F> B REMOVE CONSOLE BOX INSERT FRONT NO.2 (a) Disengage the 2 claws. (b) Pull the console box insert front No. 2 rearward to remove it. 2 Claws B REMOVE CONSOLE BOX INSERT 16. REMOVE CONSOLE UPPER PANEL GARNISH FRONT (a) Disengage the 5 clips and remove the console upper panel garnish front, then disconnect the connectors. 5 Clips B
4 INSTRUMENT PANEL/METER 7115 <F> 17. REMOVE CONSOLE BOX LOWER (a) Remove the 2 bolts <D>. (b) Remove the 2 screws <F> and the console box lower. <D> <F> <D> B REMOVE STEERING WHEEL COVER LOWER NO REMOVE STEERING WHEEL COVER LOWER NO REMOVE HORN BUTTON ASSY (See page 6017) 21. REMOVE STEERING WHEEL ASSY (See page 508) SST ( , , , ) 22. REMOVE STEERING COLUMN COVER (See page 508) 23. REMOVE TURN SIGNAL SWITCH ASSY W/SPIRAL CABLE SUBASSY (See page 508) 24. REMOVE FRONT DOOR SCUFF PLATE LH (See page 7638) 25. REMOVE FRONT DOOR SCUFF PLATE RH (See page 7638) 26. REMOVE FRONT FLOOR FOOTREST (a) Disengage the 2 claws and remove the front floor footrest. 2 Claws B REMOVE COWL SIDE TRIM BOARD LH (a) Remove the clip. (b) Disengage the 2 clips and remove the cowl side trim board LH. B REMOVE COWL SIDE TRIM BOARD RH 3131
5 7116 INSTRUMENT PANEL/METER 29. REMOVE INSTRUMENT PANEL UNDER COVER SUBASSY NO.1 (a) Remove the screw. (b) Disengage the 2 clips and the claw, and then remove the instrument panel under cover subassy No.1. Claw B REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (a) Disengage the 2 clips and remove the instrument cluster finish panel ornament. B REMOVE SWITCH HOLE BASE NO REMOVE INSTRUMENT PANEL FINISH PLATE (a) Remove the instrument panel finish plate. B Clips B REMOVE INSTRUMENT PANEL FINISH LOWER PANEL RH (a) Remove the 3 bolts. (b) Disconnect the hood lock control cable assy and the fuel lid lock control cable subassy. (c) Disengage the 4 clips. (d) Disconnect the connectors and remove the instrument panel finish lower panel RH. 34. REMOVE INSTRUMENT PANEL LOWER LH (a) Remove the 3 bolts and instrument panel lower LH. 3132
6 INSTRUMENT PANEL/METER REMOVE INSTRUMENT CLUSTER FINISH PANEL SUBASSY (a) Remove the 2 clips. (b) Disengage the 2 clips and remove the instrument cluster finish panel subassy. B63467 <H> <H> 36. REMOVE COMBINATION METER ASSY (a) Remove the 4 screws <H>. (b) Loosen the 2 bolts and remove the combination meter assy. <H> <H> B REMOVE INSTRUMENT PANEL REGISTER ASSY NO.1 (a) Remove the screw. (b) Disengage the 3 claws and remove the instrument panel register assy No.1. 3 Claws B REMOVE INSTRUMENT PANEL UNDER COVER NO.2 (a) Remove the screw. (b) Disengage the 3 clips and remove the instrument panel under cover No.2. 3 Clips B REMOVE INSTRUMENT PANEL ORNAMENT (a) Disengage the 4 clips and remove the instrument panel ornament. 4 Clips B
7 7118 INSTRUMENT PANEL/METER 40. DISCONNECT PASSENGER AIRBAG CONNECTOR (See page 6028) 41. REMOVE GLOVE COMPARTMENT DOOR ASSY (a) Remove the 5 screws. (b) Disengage the 2 clips and remove the glove compartment door assy, then disconnect the connectors. B REMOVE INSTRUMENT PANEL REGISTER ASSY NO REMOVE DISC PLAYER CHANGER W/BRACKET (W/ DISC PLAYER CHANGER) (See page 6726) 44. REMOVE ASSIST GRIP ASSY (See page 7638) 45. REMOVE FRONT PILLAR GARNISH LH (See page 7638) 46. REMOVE FRONT PILLAR GARNISH RH (See page 7638) 3134
8 INSTRUMENT PANEL/METER REMOVE W/DEFROSTER NOZZLE DUCT (a) Remove the 9 bolts and nut <A>. (b) Disconnect the connectors. (c) Remove the instrument panel safety pad subassy w/ defroster nozzle duct. <B> <A> B REMOVE DEFROSTER NOZZLE ASSY (a) Remove the 5 screws <I> and defroster nozzle assy. 49. REMOVE HEATER TO REGISTER DUCT NO.3 (a) Remove the 2 screws <I> and heater to register duct No REMOVE SIDE DEFROSTER NOZZLE DUCT NO REMOVE SIDE DEFROSTER NOZZLE DUCT NO REMOVE AUTOMATIC LIGHT CONTROL SENSOR 53. REMOVE INSTRUMENT PANEL WIRE NO REMOVE CONNECTOR NO.2 HOLDER 55. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUBASSY NO.1 (W/ 12 SPEAKER) 56. REMOVE STEREO COMPONENT SPEAKER ASSY FRONT (W/ 12 SPEAKER) (See page 6718) 57. REMOVE ANTENNA CORD SUBASSY (See page 6730) 58. REMOVE NAVIGATION ANTENNA ASSY (W/ NAVIGATION SYSTEM) (See page 6736) 59. REMOVE INSTR PNL PASS L/DOOR AIR BAG ASSY (See page 6028) 60. REMOVE 61. INSTALL INSTR PNL PASS L/DOOR AIR BAG ASSY (See page 6028) 3135
9 7120 INSTRUMENT PANEL/METER 62. INSTALL W/DEFROSTER NOZZLE DUCT (a) Using a torque wrench, install the bolt <B>. Torque: 20 N m (204 kgf cm, 14 ft lbf) <B> <A> B
10 INSTRUMENT PANEL/METER 7121 B INSTALL COMBINATION METER ASSY (a) Pull the check pin backward while pressing the check pin with a flathead screwdriver as shown in the illustration. (b) Check that the wire harness connector is engaged in the instrument panel safety pad installation position. (c) Install the 4 screws in order as shown in the illustration. (d) Tighten the 2 connector fitting bolts until a clicking sound can be heard. (e) After tightening, check that the check pin protrudes. Check Pin Check Pin B ADJUST SPIRAL CABLE SUBASSY (See page 6025) 65. INSTALL STEERING WHEEL ASSY (See page 508) 66. INSTALL HORN BUTTON ASSY (See page 6017) 67. INSPECT HORN BUTTON ASSY (See page 6011) 68. INCLINATION SENSOR ZERO DEGREE CORRECTION (See page 7123) 69. INSPECT SRS WARNING LIGHT (See page 05973) 3137
Code Shape Code Shape. φ = 6 (0.31) (0.24) (A) (B) (C) L = 18 L = 20 (0.71) φ = 5 (0.24) (0.20) (D) (E) (F) L = 16 L = 14 (0.63)
7110 INSTRUMENT PANEL/METER 7108S01 REPLACEMENT HINT: COMPONENTS: See page 717 1. TABLE OF BOLT, SCREW AND NUT HINT: Indicate the bolts, screws and nuts, which are necessary for installation and removal
A750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM000002BHN007X
A750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Last Modified: 4-26-2007 Service Category: Drivetrain 1.6 A Section: Automatic Transmission/Transaxle Model Year: 2007 Model:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.
Page 1 of 12 Last Modified: 9-21-2007 1.6 A Service Category: Vehicle Interior Section: Interior Panels/Trim Model Year: 2008 Model: Tundra Doc ID: RM000002VHU003X Title: INSTRUMENT PANEL: INSTRUMENT PANEL
REMOVAL. 6. REMOVE LOWER FINISH PANEL Using a screwdriver, remove the lower finish panel. HINT: Tape the screwdriver tip before use.
BO90 REMOVAL 1. REMOVE FRONT SEATS (See page BO105 or BO1 12) 2. REMOVE FRONT DOOR WEATHERSTRIPS 3. REMOVE FRONT PILLAR GARNISHES 4. REMOVE STEERING WHEEL PAD (See page SR14 ) 5. REMOVE COLUMN COVERS BO2PV02
Symptom Suspect Area See page 1. Wire Harness or Connector 2. ECM 2. ECM. 1. Wire Harness or Connector 2. Skid control ECU 3. Combination Meter Assy
COMBINATION METER 711 COMBINATION METER PROBLEM SYMPTOMS TABLE Warning Lights and Buzzer: 7105L01 Symptom Suspect Area See page Check Engine warning light does not light up. 2. ECM 051, 05173 Discharge
REPLACEMENT. HINT: The installation procedures are the removal procedures in reverse order.
REPLACEMENT The installation procedures are the removal procedures in reverse order. 7615 7610301 1. REMOVE FRONT DOOR SCUFF PLATE RH (a) Using a screwdriver, disengage the 2 claws and 3 clips, and remove
Model Year: 2008 Model: xb Doc ID: RM000001XUW004X
1 of 18 2/28/2008 10:41 AM Last Modified: 2-12-2007 Service Category: Vehicle Interior 1.6 A Section: Interior Panels/Trim Model Year: 2008 Model: xb Doc ID: RM000001XUW004X Title: INTERIOR: ROOF HEADLINING:
ON-VEHICLE INSPECTION
51 Connector Front Side: A5 ON-VEHICLE INSPECTION 1. INSPECT TOWING CONVERTER RELAY (a) Measure the voltage and check the result in accordance with the value(s) in the table below. Standard E064833E01
Removal and Installation
Page 1 of 14 Removal and Installation Work item table PARTS INSTRUMENT PANEL ASSEMBLY COMBINATION METER DISPLAY UNIT AV control unit CENTER CONSOLE ASSEMBLY Rear console assembly [1] [1] Instrument garnish
ROOF HEADLINING ASSY EXTERIOR/INTERIOR TRIM 760VC 02 REPLACEMENT
REPLACEMENT 7627 The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the LH side, use the same procedures as
REMOVAL IR 11. Slide the inner rear view mirror.
11 Slide REMOVAL CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-1). 1. DISCONNECT
OVERHAUL. NOTICE: Do not apply grease to each sliding part of the link. HINT: COMPONENTS: See page REMOVE REAR FLOOR FINISH PLATE
7528 ENGINE HOOD/DOOR OVERHAUL NOTICE: Do not apply grease to each sliding part of the link. COMPONENTS: See page 7526 7506701 1. REMOVE REAR FLOOR FINISH PLATE Using a screwdriver, remove the rear floor
INSTRUMENT PANEL ASSEMBLY. INSTRUMENT PANEL ASSEMBLY Component Parts Drawing IP-10 PFP:68200 AIS005BC PIIB0009E
INSTRUMENT PANEL ASSEMBLY Component Parts Drawing PFP:68200 AIS005BC PIIB0009E IP-10 1. Passenger air bag module 2. Front defroster grille (LH) 3. Front defroster grille (RH) 4. Cluster Lid A 5. Instrument
Removal & Installation
Page 1 of 11 2011 Nissan Rogue : Body > Interior > Instrument Panel > Removal & Installation Removal & Installation 1. Before servicing the vehicle, refer to the Precautions Section. CAUTION Always work
OVERHAUL. 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Using a screwdriver, remove the lower frame bracket garnish.
OVERHAUL The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the RH side, use the same procedures as on the
REMOVAL AND INSTALLATION
501-01-1 Body System Interior 501-01-1 REMOVAL AND INSTALLATION Instrument Panel CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result.
1. General Description
EXERIOR/INERIOR RIM 1. General Description A: COMPONEN 1. FRON GRILLE General Description EI-00627 Front grille Front grille emblem Front grille clip 2. UNDER COVER EI-00681 ightening torque: N m (kgf-m,
2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS
2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When
IR 13 INTERIOR ROOF HEADLINING REMOVAL
INTERIOR ROOF HEADLINING 13 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH (See page SE-43) 3. REMOVE REAR SEATBACK ASSEMBLY RH (See page SE-43)
REAR BUMPER COMPONENTS. Luggage Compartment. Trim Cover Assy RH. Rope Hook Assy. Deck Trim Side Board LH. Deck Trim Side Board RH.
767 COMPONENTS 7615701 Deck Trim Side Board LH Deck Trim Side Board RH Luggage Compartment Trim Cover Assy RH Luggage Compartment Floor Mat Luggage Compartment Trim Cover Assy LH Rear Floor Finish Plate
ED 13. ENGINE HOOD / DOOR FRONT DOOR (w/ Power Window) DISASSEMBLY
13 B088092E01 DISASSEMBLY Use the same procedures for both the LH and RH sides. 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Disengage the
DISASSEMBLY. 1 of 9 2/28/ :48 AM 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR ARMREST BASE UPPER PANEL
1 of 9 2/28/2008 10:48 AM Last Modified: 2-12-2007 1.6 A Service Category: Vehicle Exterior Section: Door/Hatch Model Year: 2008 Model: xb Doc ID: RM000001CE100DX Title: ENGINE HOOD / DOOR: FRONT DOOR:
STEERING SYSTEM PRECAUTION SR 1
System Name Power Window Control System STEERING COLUMN STEERING SYSTEM STEERING SYSTEM PRECAUTION 1 1. HANDLING PRECAUTIONS FOR S AIRBAG SYSTEM (SEE PAGE RS-1) 2. HANDLING PRECAUTIONS FOR STEERING COLUMN
75 5 ENGINE HOOD/DOOR
OVERHAUL Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. 755 750DN01 1. REMOVE
GENERAL INFORMATION HANDLING PRECAUTIONS
BODY BO1 BO2 BODY GENERAL INFORMATION GENERAL INFORMATION HANDLING PRECAUTIONS Taping When it is possible that the body or parts may be scratched during the operation, apply protective tape before starting
SCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
TOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT
Preparation Part Number: Mounting Kit PT546-06061 Tuner Assy 86180-0W030 Tuner Assy Kit Contents (86180-0W030) 1 1 Tuner Assy, Stereo Component Mounting Kit Contents (PT546-06061) 1 Ground Cable 1 1 Wire,
Replacement Cluster Fascia Replacement
1 of 12 11/1/2013 9:13 AM SOUL(AM) >2010 > G 2.0 DOHC > Body (Interior and Exterior) Replacement Cluster Fascia Replacement When prying with a flat-tip screwdriver, wrap it with protective tape, and apply
2. NOTE: On vehicles equipped with automatic transmissions, move the shift lever to the 1 position to ease removal.
Page 1 of 28 Section 501-12: Instrument Panel and Console REMOVAL AND INSTALLATION 1997 F-150, F-250 Workshop Manual Instrument Panel Removal 1. WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY,
FRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH
761 FRONT BUMPER FRONT BUMPER COMPONENTS 760HX02 Front Bumper Side Mounting Bracket RH Front Bumper Reinforcement 36 (367, 27) Front Bumper Side Mounting Bracket LH 36 (367, 27) 5.0 (51, 44 in. lbf) Front
SCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
REASSEMBLY IR INSTALL ROOF WIRE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining.
31 REASSEMBLY 1. INSTALL ROOF WE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining. Double-sided Tape Marking B130653E01 (b) NOTICE: Apply the tape securely
REMOVAL AND INSTALLATION
501-12-1 Instrument Panel and Console 501-12-1 REMOVAL AND INSTALLATION Instrument Panel Removal 1. If equipped with power seats, move the seat fully rearward. 2. If equipped with adjustable pedal system,
TOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
2012 Camry DISASSEMBLY Hint: Report a problem with this article Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PRECAUTION NOTICE: After turning the
FLOOR SHIFT SHIFT LEVER ASSY (MTM)
4110 FLOOR SHIFT SHIFT LEVER ASSY (MTM) FLOOR SHIFT SHIFT LEVER ASSY (MTM) COMPONENTS 4105U03 Gasoline Engine: Front Floor Heat Insulator No.1 Console Panel Subassy Upper Floor Shift Lever Knob Subassy
TOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
SEAT BELT WARNING SYSTEM
WARNING SYSTEM LOCATION WARNING SYSTEM 611 6105001 Combination Meter (Driver s Seat Belt Warning Lamp) Clock Assy (Passenger s Seat Belt Warning Lamp) Seat Belt Warning Sensor Front Seat Inner Belt Assy
Scion xa SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS
SCION tc Navigation System Preparation. Part Number: PT
Preparation Part Number: PT611-21111 Kit Contents Item # Quantity Reqd. Description 1 1 Navigation System 2 1 GPS Antenna 3 1 Bluetooth Antenna 4 1 Wire Harness (Reverse / Park Brake) 5 1 RCA Relay Cable
FLOOR SHIFT ASSEMBLY
FLOOR SHIFT ASSEMBLY Components Removal 1. REMOVE THESE PARTS: a. Front door scuff plates b. Cowl side trim c. Lower finish panels d. Lower LH insert e. Lower instrument panel f. Lower RH panel g. Ash
SECTION 1A3 - INSTRUMENT PANEL AND CONSOLE
SECTION 1A3 - INSTRUMENT PANEL AND CONSOLE Click on the button for more information. CAUTION: This vehicle will be equipped with a Supplemental Restraint System (SRS). A SRS will consist of either seat
OVERHAUL HINT: COMPONENTS: See page 74 49
7451 OVERHAUL COMPONENTS: See page 7449 7402R01 1. MOVE ROOF PANEL TO HALF Refer to the manual operation procedures, and halfopen the roof. H40336 A A:100 mm (3.94 in.) or less 2. REMOVE REAR SEAT CUSHION
Telescopic Lever Detent Clip Replacement
T-SB-0147-13 September 27, 2013 Service Category Steering Section Steering Column Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 2012 Avalon SUPERSESSION NOTICE The information contained
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F 2002 THROUGH EARLY 2004 MODEL YEAR NORTH AMERICAN PRODUCED (NAP) TOYOTA CAMRY CURTAIN SIDE AIRBAG Page 1 of 26 I. OPERATION FLOW CHART Verify Vehicle
TOYOTA SIENNA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit: PT546-08070 Tuner Assy: 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting Kit Contents
2002 Explorer Sport/Sport-Trac Workshop Manual
Page 1 of 18 SECTION 501-12: Instrument Panel and Console REMOVAL AND INSTALLATION 2002 Explorer Sport/Sport-Trac Workshop Manual Instrument Panel Removal All vehicles CAUTION: Electronic modules are sensitive
ED 42. ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window)
42 ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window) (g) (h) Horizontally and vertically adjust the door by loosening the door side hinge bolts. Tighten the door side hinge bolts after the adjustment. Torque:
SCION xb SIRIUS SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS3-52050 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description Antenna, Exterior 2 Wire Harness 3 Bracket,
file://c:\program Files\tsocache\OFFICE_5164\SYA~us~en~file=SYA1C003.htm~gen~re...
Page 1 of 26 SECTION 501-12: Instrument Panel and Console 2000 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/21/1999 Instrument Panel Removal CAUTION:
Sensor A/C Ambient Temperature 1951
SECTION 412-04: Control Components REMOVAL AND INSTALLATION Sensor A/C Ambient Temperature Removal 1. Remove the radiator upper sight shield. 2. Disconnect the wire harness connector. 3. Remove the A/C
REMOVAL AND INSTALLATION
501-12-1 Instrument Panel and Console 501-12-1 REMOVAL AND INSTALLATION Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage
SHOCK ABSORBER ASSY FRONT LH
2612 REPLACEMENT COMPONENTS: See page 263 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. REMOVE FRONT WHEEL 260H802 2. SEPARATE FRONT STABILIZER
SRS LIGHT "ON" - B0111/B OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB , Date of Issue: June 23, 2010
SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT -2006 Toyota Sienna... Page 1 of 27 SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB-0162-10,
POWER WINDOW CONTROL SYSTEM
POWER WINDOW CONTROL SYSTEM ONVEHICLE INSPECTION POWER WINDOW CONTROL SYSTEM 1. CHECK POWER WINDOW (MANUAL OPERATION FUNCTION) (a) Turn the ignition switch ON. (b) Check that the door glass will rise when
Prius XM Radio Installation Instructions. Eddie Bell
2004-2005 Prius XM Radio Installation Instructions By Eddie Bell www.metrotpn.com 1 Let me begin by saying this is an easy but time consuming job. Set aside a few hours of your time for the install. If
REPLACEMENT 1. REMOVE FRONT WHEEL
3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake
Part Number: TAV-713 TOYOTA AVALON LED DRL
Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad 6 1 Switch 7 2 Drill Jigs Hardware Bag Contents
LEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
OVERHAUL. HINT: COMPONENTS: FLOOR SHIFT ASSY (See page 40 35) 1. REMOVE CONSOLE BOX REAR COVER 2. REMOVE CONSOLE BOX CARPET
4037 OVERHAUL COMPONENTS: FLOOR SHIFT ASSY (See page 4035) 1. REMOVE CONSOLE BOX REAR COVER 2. REMOVE CONSOLE BOX CARPET 4013O01 Front side of vehicle 3. REMOVE CONSOLE BOX SUBASSY REAR (a) Remove the
GENERAL INFORMATION HANDLING PRECAUTIONS
BO1 BO2 GENERAL INFORMATION GENERAL INFORMATION HANDLING PRECAUTIONS BO01M01 Taping When it is possible that the body or parts may be scratched during the operation, apply protection tape before starting
1 of 6 10/31/2017, 1:57 PM. Fig. 19 Automatic Transmission Shift Knob Removal
1 of 6 10/31/2017, 1:57 PM Fig. 19 Automatic Transmission Shift Knob Removal 2 of 6 10/31/2017, 1:57 PM Fig. 20 Manual Transmission Shift Knob Removal 3 of 6 10/31/2017, 1:57 PM Fig. 21 Removing Accessory
DISPOSAL. CAUTION: Never dispose of front seat outer belt which has an inactivated. activated pretensioner.
DISPOSAL When scrapping vehicles epuipped with a seat belt pretensioner or disposing of a front seat outer belt (with seat belt pretensioner) always first active the seat belt pretensioner in accordance
INSTRUMENT PANEL ASSEMBLY
2003 Dodge or Ram Truck RAM 1500 Truck 2WD V8-4.7L VIN N Vehicle > Body and Frame > Interior Moulding / Trim > Dashboard / Instrument Panel > Service and Repair > Removal and Replacement INSTRUMENT PANEL
Text in Illustration
ON-VEHICLE INSPECTION If using a dropper to adjust the fluid amount, make sure that the dropper has not been used with mineral oils, water or deteriorated brake fluid. Sealed areas may deteriorate and
SRS AIRBAG Toyota RAV4. Supplemental Restraint System - RAV4 PRECAUTION CAUTION:
2005 RESTRAINTS Supplemental Restraint System - RAV4 SRS AIRBAG PRECAUTION CAUTION: The TOYOTA RAV4 is equipped with SRS that includes a driver airbag, front passenger airbag, side airbag and curtain shield
REMOVAL JS - CHRYSLER L V6 V.V.T Body / Instrument Panel / PANEL, Instrument/Removal
2011 - JS - CHRYSLER 200-3.6L V6 V.V.T. 23 - Body / Instrument Panel / PANEL, Instrument/Removal REMOVAL NOTE: Avenger shown, 200 typical, except where noted. 1. Disconnect and isolate the negative battery
INTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52A-1 INTERIOR AN SUPPLEMENTAL RESTRAINT SYSTEM (SRS) CONTENTS INTERIOR... 52A SUPPLEMENTAL RESTRAINT SYSTEM (SRS)... 52B 52A-2 INTERIOR CONTENTS SPECIAL TOOL... 3 INSTRUMENT PANEL*... 3 FRONT FLOOR CONSOLE...
Conflicts. TOYOTA Camry XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly)
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description 1 1 XM Module 2 1 XM Tuner Module 3 1 Wiring Harness 4 1 Hardware
CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT
REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE
TOYOTA LAND CRUISER 2003 DVD VES
LEXUS LX470 Section I Installation Preparation Part Number: PT296 6002D 03/16 (LC) PT296 6002L 03/16 (LX) Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 FPD Assembly
TOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)
Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting
1 of 12 8/18/ :52 AM
1 of 12 8/18/2016 11:52 AM REMOVAL 1. DISCHARGE FUEL SYSTEM PRESSURE a. Discharge fuel system pressure. 2. REMOVE DECK BOARD SUB-ASSEMBLY a. Disengage the 5 clips and turn up the front side of the deck
TOYOTA TACOMA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,
SCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT
Section I Installation Preparation Part Number: PT900-52080 Kit Contents Item # Quantity Reqd. Description 1 2 DVD Headrest Unit 2 2 Headrest Extension Cables 3 1 Audio Interface Module 4 1 Audio Interface
Model Year: 2008 Model: xb Doc ID: RM000000SUR00OX. (a) Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.
WINDSHIELD / WINDOWGLASS: WINDSHIELD GLASS: INSTALLATION (2008 x... Page 1 of 10 Last Modified: 2-12-2007 Service Category: Vehicle Exterior 1.6 A Section: Window/Glass Model Year: 2008 Model: xb Doc ID:
XM Adapter Cable (P/N: ) MUST be used for this vehicle.
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 XM Adapter Cable (P/N: 00016-00076-10) MUST be used for this vehicle. Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description
TECHNICIAN SAFETY INFORMATION
2009 Honda Accord L4-2.4L Vehicle > Restraints and Safety Systems > Air Bag Systems > Service Precautions TECHNICIAN SAFETY INFORMATION SRS Precautions and Procedures General Precautions NOTE: Some systems
1. General Description
EXERIOR/INERIOR RIM GENERAL DESCRIPION 1. General Description A: COMPONEN 1. FRON GRILLE EI-00413 Front grille Front grille emblem Clip 2. UNDER COVER EI-00414 Under cover Clip (side) ightening torque:
VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 PRECAUTION... 2 PREPARATION... 4 FUNCTION DIAGNOSIS...
VENTILATION, HEATER & AIR CONDITIONER SECTION VTL A VENTILATION SYSTEM B C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK IMPREZA. Installation Instruction. No. Name Qty Socket ASSY 1 Plug 1 Ring 1 TOOLS NEEDED
02 EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK IMPREZA PART No. EN: COMPONENTS No. Name Qty Socket ASSY 1 Plug 1 Ring 1 Installation Instruction H6710AL010 1 2 3 TOOLS NEEDED PRECAUTIONS Please refer to
EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK, IMPREZA, ASCENT,FORESTER. Installation Instruction. No. Name Qty Socket ASSY 1 Plug 1 Ring 1 TOOLS NEEDED
04 EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK, IMPREZA, ASCENT,FORESTER Installation Instruction PART No. H6710AL010 EN: COMPONENTS No. Name Qty Socket ASSY 1 Plug 1 Ring 1 1 2 3 TOOLS NEEDED PRECAUTIONS
SLIDING ROOF SYSTEM LOCATION. Sliding Roof Drive Gear Sub Assy (Include Sliding Roof Limit Switch)
/CONVERTIBLE SYSTEM 741 SYSTEM LOCATION 7405N02 Sliding Roof Drive Gear SubAssy (Include Sliding Roof Limit Switch) Sliding Roof Switch Assy (Include Power Window Relay) Sliding Roof Housing A65611 1815
ILLUSTRATION ILLUSTRATION
ILLUSTRATION ILLUSTRATION REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. When the brake pedal is depressed or the door courtesy switch is turned on even if the
TOYOTA RAV TRAILER WIRE HARNESS Section I Installation Preparation
Section I Installation Preparation Part Number: 08921-42900 Kit Contents Item # Quantity Reqd. Description 1 1 Converter 2 1 Wire harness 3 1 Sub wire harness No.1 4 2 Plastic Tie (300mm) 5 21 Plastic
VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 FUNCTION DIAGNOSIS... 3 PRECAUTION... 6 PREPARATION...
VENTILATION, HEATER & AIR CONDITIONER SECTION VTL A VENTILATION SYSTEM B C D CONTENTS E FUNCTION DIAGNOSIS... 3 AUTOMATIC AIR CONDITIONER SYSTEM... 3 WITH COLOR DISPLAY...3 WITH COLOR DISPLAY : Switches
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. (Trunk Mount) 2009 CIVIC 4-DOOR AII 40184 Issue Date AUG 2008 PARTS LIST 8 Cushion tapes Changer Attachment (Sold Separately) P/N 08B26-SNA-101
SCION XB SUBWOOFER ENCLOSURE Preparation
Preparation Part Number: Kit Contents Item # Quantity Reqd. Description 1 1 Subwoofer enclosure 2 1 Wire Harness 3 1 Paper Template 4 1 Plastic Drill Template 5 1 Hardware Bag Hardware Bag Contents 1 Item
TOYOTA Matrix XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-12080 Tuner Assembly 86180-0W031 (Music Only) Tuner Assembly PT546-00090 (Music Plus Data) NOTE: Part number of this accessory may not be the same as the part
SCION tc ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PTS21-21070 Kit Contents Item # Quantity Reqd. Description 1 2 Hardware Kit w/ power harness 2 1 Front Left Illuminated Door Sill Protector 3 1 Front Right Illuminated Door Sill
1. General Description
General Description 1. General Description A: COMPONENT (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (24) (23) (22) (21) (20) (19) (18) (17) (16) (15) (14) (13) (12) (11) AB-02007 (1) Curtain airbag module
Part Number: TAV-713. Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL. Hardware Bag Contents.
Date: 09.04.2013 TOYOTA AVALON 2013 - LED DRL Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad
SCION tc 2005 LEATHER STEERING WHEEL Preparation. Part Number: (Silver/Dark Gray)
Preparation Part Number: 08460 21810 (Silver/Dark Gray) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description 1 1 Steering Wheel
SCION tc PREMIUM AUDIO Preparation. Part Number: PT (Extension Module w/ AHA)
Preparation Part Number: PT296-12160 Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna kit 5 6 Bolt (M5x8) 6 5 Wire tie (10 ) Hardware
SRS AIRBAG PRECAUTION
SRS AIRBAG PRECAUTION SRS AIRBAG The LEXUS ES300 is equipped with SRS, which comprises a driver airbag and a front passenger airbag. Failure to carry out service operations in the correct sequence could
FRONT AXLE HUB SUB-ASSY LH
3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)
DISPOSAL HINT: CAUTION: Never dispose of the horn button assy that has an undeployed
DISPOSAL 6015 When scrapping a vehicle equipped with the SRS or disposing of the horn button assy, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality
Instrument Panel Assembly Replacement. Fig. 14 Battery Negative Cable Removal/Installation
Page 1 of 11 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2003 Chrysler Truck PT Cruiser L4-2.4L VIN B Conversion