CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT

Size: px
Start display at page:

Download "CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT"

Transcription

1 REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE 0) 6. REMOVE OIL LEVEL GAUGE GUIDE SUBASSY (SEE PAGE ). REMOVE EXHAUST MANIFOLD SUBASSY RH (SEE PAGE ). REMOVE EXHAUST MANIFOLD SUBASSY LH (SEE PAGE ) 9. REMOVE DRIVE PLATE & RING GEAR SUBASSY (SEE PAGE 0) SST (093000), FIX ENGINE ASSY. REMOVE IDLER PULLEY SUBASSY NO.. REMOVE ENGINE MOUNTING BRACKET RH (SEE PAGE ) 3. REMOVE VRIBBED BELT TENSIONER ASSY (SEE PAGE ). REMOVE WATER PUMP PULLEY (SEE PAGE 60) SST ( , ). REMOVE TIMING GEAR COVER NO. 6. REMOVE ENGINE MOUNTING STAY NO. RH (SEE PAGE ). REMOVE ENGINE MOUNTING BRACKET FRONT NO. LH (SEE PAGE ). REMOVE WATER INLET HOUSING (SEE PAGE 60) 9. REMOVE CRANKSHAFT PULLEY (SEE PAGE ) SST (093000), , (099000, , , 09900) 0. REMOVE OIL PAN SUBASSY NO. (SEE PAGE ) SST REMOVE OIL STRAINER SUBASSY (SEE PAGE ). REMOVE OIL PAN SUBASSY (SEE PAGE ) 3. REMOVE INTAKE AIR SURGE TANK (SEE PAGE ). REMOVE IGNITION COIL ASSY. REMOVE OIL PIPE NO. (SEE PAGE ) 6. REMOVE OIL PIPE NO. (SEE PAGE ). REMOVE CYLINDER HEAD COVER SUBASSY RH (SEE PAGE ). REMOVE CYLINDER HEAD COVER SUBASSY LH (SEE PAGE ) 9. REMOVE TIMING CHAIN COVER SUBASSY (SEE PAGE ) 30. REMOVE TIMING CHAIN COVER OIL SEAL (SEE PAGE ) 3. SET NO. CYLINDER TO TDC/COMPRESSION (SEE PAGE ) 3. REMOVE CHAIN TENSIONER ASSY NO. (SEE PAGE ) 33. REMOVE CHAIN SUBASSY (SEE PAGE ) 30

2 6 ENGINE MECHANICAL 3. REMOVE CAMSHAFT TIMING GEARS AND NO. CHAIN (LH BANK) must be kept level while it is being removed. If the Push (a) While pushing down the chain tensioner No.3, insert a pin of φ.0 mm (0.039 in.) into the hole to fix it. A966 A96 Turn Hold G090 A963 (b) Hold each hexagonal portion of the No.3 camshaft and No. camshaft with a wrench, and remove the camshaft timing gear set bolt. Be careful not to damage the cylinder head with the wrench. Do not disassemble the camshaft timing gear assembly. (c) Separate the camshaft timing gears with the No. chain subassy. 3. REMOVE CHAIN TENSIONER ASSY NO.3 (a) Remove the bolt and chain tensioner No REMOVE CAMSHAFTS must be kept level while it is being removed. If the (a) Remove the 3 gaskets. G03 30

3 (b) Make sure that the knock pin of the camshaft is positioned as shown in the illustration. Front View G00 G09 Knock Pin G3 (c) Using several steps, loosen and remove the bearing cap bolts in the sequence shown in the illustration. 6 3 G G09 (d) Using several steps, loosen and remove the bearing cap bolts in the sequence shown in the illustration. (e) Remove the camshaft bearing caps, then remove the camshafts. Uniformly loosen the bolts while keeping the camshaft level. Do not pry the camshaft with a tool by applying excessive force to it. Do not damage the intake and exhaust parts on the cylinder head side. HINT: Make sure the removed parts are returned to the same places they were removed from. 306

4 ENGINE MECHANICAL 3. REMOVE CAMSHAFT HOUSING SUBASSY LH (a) Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver. Be careful not to damage the contact surfaces of the cylinder head and camshaft housing. HINT: Tape the screwdriver tip before use. Protective Tape Protective Tape G INSTALL CAMSHAFT TIMING GEAR (SEE PAGE ) 39. INSPECT CAMSHAFT TIMING GEAR ASSY (SEE PAGE ) 0. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSY LH (SEE PAGE ). REMOVE CAMSHAFT TIMING GEAR (SEE PAGE ). INSTALL CAMSHAFTS must be kept level while it is being installed. If the Stem End Cap Rocker Arm (a) Install the camshaft and No. camshaft to the camshaft housing subassy. Before and after setting the camshaft and No. camshaft, check that the rocker arm is firmly set to the lash adjuster. CORRECT INCORRECT Lash Adjuster G3 (b) (c) (d) Apply engine oil to the camshaft journal, camshaft housing and bearing cap. Install the No.3 camshaft and No. camshaft to the camshaft housing LH. Confirm the marks and numbers on the camshaft bearing caps and place them in each proper position and direction. A969 30

5 9 3 (e) Using several steps, install and temporarily tighten the bearing cap bolts uniformly in the sequence as shown in the illustration. Torque: 0 N m (0 kgf cm, ft lbf) 6 G9 3. to. (0.3 to 0.) : Seal Packing mm (in.) G0 3. INSTALL CAMSHAFT HOUSING SUBASSY LH (a) Apply seal packing in a continuous bead as shown in the illustration. Seal packing: Part No or equivalent Seal diameter: 3. to. mm (0.3 to 0. in.) Remove any oil from the contact surface. Install the camshaft housing subassy LH within 3 minutes and tighten the bolts within minutes after applying seal packing. Do not start the engine for at least hours after installation (b) Install the camshaft housing LH, and tighten the 3 bolts in the order shown in the illustration. Torque: N m ( kgf cm, ft lbf) Make sure that the knock pin of the camshaft is positioned as shown in the illustration before installing the camshaft housing LH. Front View G09 Knock Pin G0 3 6 (c) Using several steps, tighten the 9 bearing cap bolts uniformly in the sequence as shown in the illustration. Torque: 6 N m (63 kgf cm, ft lbf) Remove all excess seal packing after installing the bearing cap bolts. G09 30

6 0 ENGINE MECHANICAL (d) Install 3 new gaskets. G03 A96. INSTALL CHAIN TENSIONER ASSY NO.3 (a) Install the chain tensioner No.3 with the bolt. Torque: N m ( kgf cm, ft lbf) (b) While pushing in the tensioner, insert a pin of φ.0 mm (0.039 in.) into the hole to fix it.. INSTALL CAMSHAFT TIMING GEARS AND NO. CHAIN (LH BANK) must be kept level while it is being installed. If the Timing Marks Mark Links (a) Align the mark links (yellow) with the timing marks of the camshaft timing gears as shown in the illustration. (b) Apply a small amount of engine oil to the bolt threads and boltseating surface. (c) Align the knock pin of the camshaft with the pin hole of the camshaft timing gear. Install the camshaft timing gear and camshaft timing exhaust gear LH with the No. chain installed. Do not push the camshaft timing gear assembly to the camshaft forcibly when installing it. G093 Turn Hold (d) (e) Hold the hexagonal portion of the camshaft with a wrench, and tighten the bolts. Torque: 00 N m (,00 kgf cm, ft lbf) Remove the pin from the tensioner. G

7 6. INSTALL CHAIN TENSIONER ASSY NO. (SEE PAGE ). INSTALL TIMING CHAIN COVER OIL SEAL (SEE PAGE ) SST ( ). INSTALL TIMING CHAIN COVER SUBASSY (SEE PAGE ) 9. INSTALL WATER INLET HOUSING (SEE PAGE 60) 0. INSTALL ENGINE MOUNTING BRACKET FRONT NO. LH (SEE PAGE ) Install engine mounting bracket front No. LH within minutes after apply FIPG to timing chain cover.. INSTALL CYLINDER HEAD COVER SUBASSY LH (SEE PAGE ). INSTALL CYLINDER HEAD COVER SUBASSY RH (SEE PAGE ) 3. INSTALL OIL PIPE NO. (SEE PAGE ). INSTALL OIL PIPE NO. (SEE PAGE ). INSTALL IGNITION COIL ASSY Torque: 0 N m (0 kgf cm, ft lbf) 6. INSTALL INTAKE AIR SURGE TANK (SEE PAGE ). INSTALL OIL PAN SUBASSY (SEE PAGE ). INSTALL OIL STRAINER SUBASSY (SEE PAGE ) 9. INSTALL OIL PAN SUBASSY NO. (SEE PAGE ) 60. INSTALL CRANKSHAFT PULLEY (SEE PAGE ) SST (093000), INSTALL ENGINE MOUNTING STAY NO. RH (SEE PAGE ) 6. INSTALL TIMING GEAR COVER NO. 63. INSTALL WATER PUMP PULLEY (SEE PAGE 60) SST ( , ) 6. INSTALL VRIBBED BELT TENSIONER ASSY (SEE PAGE ) 6. INSTALL ENGINE MOUNTING BRACKET RH (SEE PAGE ) 66. INSTALL IDLER PULLEY SUBASSY NO. 6. REMOVE ENGINE ASSY 6. INSTALL DRIVE PLATE & RING GEAR SUBASSY (SEE PAGE 0) SST (093000), INSTALL EXHAUST MANIFOLD SUBASSY LH (SEE PAGE ) 0. INSTALL EXHAUST MANIFOLD SUBASSY RH (SEE PAGE ). INSTALL OIL LEVEL GAUGE GUIDE SUBASSY (SEE PAGE ). INSTALL AUTOMATIC TRANSAXLE ASSY (SEE PAGE 0) 3. INSTALL STARTER ASSY (SEE PAGE 99). INSTALL FRONT FRAME ASSY (SEE PAGE ). INSTALL ENGINE WIRE 6. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ) 300

25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets.

25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets. CAMSHAFT (RH BANK) (2GRFE) REPLACEMENT 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE 1421) 2. REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE 1421) 4. REMOVE STARTER ASSY (SEE PAGE 199). REMOVE

More information

REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.

REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner. 14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

More information

11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.

11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts. 1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.

More information

1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X

1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION

More information

COMPONENTS ILLUSTRATION

COMPONENTS ILLUSTRATION COMPONENTS ILLUSTRATION ILLUSTRATION REMOVAL 1. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY (a) Remove the camshaft housing sub-assembly. 2. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR 3. REMOVE MANIFOLD STAY

More information

VALVE CLEARANCE (3ZZ FE/4ZZ FE)

VALVE CLEARANCE (3ZZ FE/4ZZ FE) ENGINE MECHANICAL ADJUSTMENT 1. REMOVE CYLINDER HEAD COVER NO.2 1487 140M901 Remove the 2 nuts, 2 clips and cylinder head cover. 2. REMOVE IGNITION COIL ASSY Disconnect the 4 connectors. (b) Remove the

More information

REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2.

REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. ENGINE MECHANICAL 1475 REPLACEMENT 141FV01 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. A66316 2. REMOVE IGNITION COIL NO.1 (a) Remove the 4 bolts and pull out

More information

2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS

2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS 2004 Toyota CAMRY Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS REPLACEMENT 1. REMOVE HOOD SU-ASSY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:

More information

CYLINDER HEAD GASKET (2AZ-FE)

CYLINDER HEAD GASKET (2AZ-FE) 190 REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 111 ) 2. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) 3. REMOVE CHAIN SUBASSY (See page

More information

3/13/ :32 AM. NOTICE: Do not disconnect the hose.

3/13/ :32 AM. NOTICE: Do not disconnect the hose. 1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install

More information

26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]

26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ] Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005

More information

VALVE CLEARANCE (1NZ-FXE)

VALVE CLEARANCE (1NZ-FXE) 146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY

More information

PARTIAL ENGINE ASSY (2TR FE)

PARTIAL ENGINE ASSY (2TR FE) COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER

More information

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)

2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) 2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475

More information

PARTIAL ENGINE ASSY (2ZZ GE)

PARTIAL ENGINE ASSY (2ZZ GE) COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy

More information

10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.

10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching. 14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE

More information

REPLACEMENT. 12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 5 bolts, the engine moving control rod and the engine mounting stay.

REPLACEMENT. 12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 5 bolts, the engine moving control rod and the engine mounting stay. 1484 ENGINE MECHANICAL REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT WIPER ARM HEAD CAP 3. REMOVE FR WIPER ARM RH (See page 668 ) 4. REMOVE FR WIPER ARM LH (See page 668 ) 5. REMOVE COWL TOP VENTILATOR

More information

Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components

Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE

More information

Page 1 of 44 REPLACEMENT 1. 2. 3. 4. REMOVE ENGINE UNDER COVER RH DRAIN COOLANT (See REPLACEMENT ) REMOVE FRONT WHEEL RH REMOVE CYLINDER HEAD COVER NO. 2 a. Remove the 2 nuts, 2 clips and cylinder head

More information

REMOVAL 7. DISCONNECT ACCELERATOR CABLE FROM THROTTLE BODY. 8. DISCONNECT HOSES (a) Remove the 2 bolts from the air intake chamber assembly.

REMOVAL 7. DISCONNECT ACCELERATOR CABLE FROM THROTTLE BODY. 8. DISCONNECT HOSES (a) Remove the 2 bolts from the air intake chamber assembly. ENGINE MECHANICAL (VZFE) EM9 REMOVAL EM1MP01 1. REMOVE ENGINE UNDER COVER. DRAIN ENGINE COOLANT. REMOVE FRONT EXHAUST PIPE (See page EM10 ). DISCONNECT HEATER HOSE. REMOVE AIR CLEANER ASSEMBLY 6. REMOVE

More information

Technical Service BULLETIN

Technical Service BULLETIN Technical Service BULLETIN May 19, 2003 Title: Models: 00 02 Celica GTS EG010-03 ENGINE Introduction In some cases, owners of 2000 2002 model year Celica GTS vehicles equipped with the 2ZZ GE engine may

More information

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide. EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle

More information

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. 144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT

More information

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly. Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE

More information

12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket.

12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket. TIMING BELT (3MZFE) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FR WIPER ARM RH (See page 669) 3. REMOVE FR WIPER ARM LH (See page 669) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 669) 5.

More information

TIMING BELT (1MZ FE Jan., 2003)

TIMING BELT (1MZ FE Jan., 2003) 14 100 TIMING BELT (1MZ FE Jan., 2003) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL RH 3. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See Pub. No. RM972U on page

More information

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)

More information

VALVE CLEARANCE (1ZZ FE)

VALVE CLEARANCE (1ZZ FE) ENGINE MECHNICL DJUSTMENT 145 140OE02 1. REMOVE CYLINDER HED COVER NO.2 (a) Remove the 2 nuts, 2 clips and cylinder head cover. 65077 2. DISCONNECT ENGINE WIRE (a) Remove the 5 clamps from the 5 clamp

More information

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.

OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap. 14218 ENGINE MECHANICAL PARTIAL ENGINE ASSY (2ZZGE) OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 140R901 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.

More information

INSTALLATION EM 21. Inward. Sensor. Plate Washer. 10 mm Hexagon Wrench SST. Fulcrum Length SST TIMING BELT ENGINE MECHANICAL 2002 AVALON (RM872U)

INSTALLATION EM 21. Inward. Sensor. Plate Washer. 10 mm Hexagon Wrench SST. Fulcrum Length SST TIMING BELT ENGINE MECHANICAL 2002 AVALON (RM872U) Inward Sensor A05060 INSTALLATION EM21 EM0ZD02 1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley, and slide on the timing pulley. (b) Install the

More information

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION

EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER

More information

13. INSTALL NO. 2 CHAIN VIBRATION DAMPER 14. INSTALL TIMING CHAIN COVER OIL SEAL

13. INSTALL NO. 2 CHAIN VIBRATION DAMPER 14. INSTALL TIMING CHAIN COVER OIL SEAL 13. INSTALL NO. 2 CHAIN VIBRATION DAMPER 14. INSTALL TIMING CHAIN COVER OIL SEAL (a) Using SST, tap in a new oil seal until its surface is flush with the timing chain cover edge. SST: 0922322010 Keep the

More information

6/6/2018 2ZR-FXE Engine Mechanical: Camshaft: Removal 2012 Toyota Prius V MotoLogic

6/6/2018 2ZR-FXE Engine Mechanical: Camshaft: Removal 2012 Toyota Prius V MotoLogic 2012 Prius V REMOVAL REMOVE ENGINE ASSEMBLY WITH TRANSAXLE Report a problem with this article More Info INSTALL ENGINE STANDMore Info REMOVE ENGINE HANGERMore Info REMOVE THROTTLE BODY ASSEMBLYMore Info

More information

SHOCK ABSORBER ASSY FRONT LH

SHOCK ABSORBER ASSY FRONT LH 2612 REPLACEMENT COMPONENTS: See page 263 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. REMOVE FRONT WHEEL 260H802 2. SEPARATE FRONT STABILIZER

More information

REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14)

REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14) EM34 ENGINE MECHANICAL (2UZFE) EM11U02 REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM14) A02844 Be careful not to drop

More information

Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002

Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 Timing Belt: Service and Repair Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 REMOVAL 1. REMOVE OUTER FR COWL TOP PANEL ASSEMBLY 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FENDER APRON SEAL 4. REMOVE GENERATOR

More information

2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1

2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1 2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL

More information

REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.

REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1. AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD

More information

INSTALLATION. Check that the idler pulley moves smoothly.

INSTALLATION. Check that the idler pulley moves smoothly. ENGINE MECHANICAL (5SFE) INSTALLATION EM23 EM08604 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000,

More information

1ZZ-FE ENGINE MECHANICAL ENGINE UNIT DISASSEMBLY. If you paid for the content in this manual you were screwed!

1ZZ-FE ENGINE MECHANICAL ENGINE UNIT DISASSEMBLY. If you paid for the content in this manual you were screwed! 1ZZ-FE ENGINE MECHANICAL ENGINE UNIT 107 DISASSBLY 1. ROVE OIL FILLER CAP SUB-ASSBLY (a) Remove the oil filler cap from the cylinder head cover. A064852 A065656 A064854 2. ROVE OIL FILLER CAP GASKET (a)

More information

OVERHAUL. 1. REMOVE OIL FILLER CAP SUB ASSY (a) Remove the oil filler cap from the cylinder head cover.

OVERHAUL. 1. REMOVE OIL FILLER CAP SUB ASSY (a) Remove the oil filler cap from the cylinder head cover. 1452 ENGINE MECHNICL OVERHUL 140QU01 1. REMOVE OIL FILLER CP SUSSY (a) Remove the oil filler cap from the cylinder head cover. 64852 2. REMOVE OIL FILLER CP GSKET (a) Using a screwdriver, remove the gasket

More information

REPLACEMENT 1. REMOVE ENGINE UNDER COVER RH. 2. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 2 screw, 3 clips and engine under cover.

REPLACEMENT 1. REMOVE ENGINE UNDER COVER RH. 2. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 2 screw, 3 clips and engine under cover. 14100 ENGINE MECHNICL REPLCEMENT 1. REMOVE ENGINE UNDER COVER RH 140OJ02 2. REMOVE CYLINDER HED COVER NO.2 (a) Remove the 2 screw, 3 clips and engine under cover. 65077 3. REMOVE FN ND GENERTOR V BELT

More information

2000 Toyota Truck Tundra. Timing Belt: Service and Repair

2000 Toyota Truck Tundra. Timing Belt: Service and Repair Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE

More information

Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair

Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI 2001 Timing Belt: Service and Repair REMOVAL 1. REMOVE GENERATOR 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FRONT FENDER APRON SEAL 4. REMOVE PS PUMP DRIVE BELT

More information

2/17/2017 Timing Belt Service and Repair, Removal and Replacement

2/17/2017 Timing Belt Service and Repair, Removal and Replacement http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com

More information

INSTALLATION. 6. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Temporarily install the crankshaft pulley bolt to the crankshaft.

INSTALLATION. 6. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Temporarily install the crankshaft pulley bolt to the crankshaft. EM19 ENGINE MECHANICAL (5VZFE) INSTALLATION EM0Z003 1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley and slide on the timing pulley. (b) Slide on

More information

ENGINE ASSEMBLY. COMPONENTS (Part 1)

ENGINE ASSEMBLY. COMPONENTS (Part 1) 1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS

More information

REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.

REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove

More information

8/14/2016 8:12 PM. Bolt: Part No for Type B

8/14/2016 8:12 PM. Bolt: Part No for Type B 1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR

More information

EM-81 EM0Z7-01 DISASSEMBLY

EM-81 EM0Z7-01 DISASSEMBLY EM81 EM0Z701 DISASSEMBLY 1. M/T: REMOVE FLYWHEEL 2. A/T: REMOVE DRIVE PLATE 3. REMOVE REAR END PLATE 4. INSTALL ENGINE TO ENGINE STAND FOR DIS ASSEMBLY 5. REMOVE TIMING BELT AND PULLEYS (See page EM13

More information

ALLDATA Online Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15. Timing Belt Installation. Timing Belt (3S-FE)

ALLDATA Online Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15. Timing Belt Installation. Timing Belt (3S-FE) ALLDATA Online - 1990 Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15 Timing Belt Installation Timing Belt (3S-FE) INSTALLATION OF TIMING BELT 1. INSTALL OIL PUMP PULLEY a. Align

More information

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender

More information

2007 Ford Freestyle SEL

2007 Ford Freestyle SEL Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold

More information

EM 6 VALVE CLEARANCE ENGINE MECHANICAL EM11I 01 ADJUSTMENT HINT:

EM 6 VALVE CLEARANCE ENGINE MECHANICAL EM11I 01 ADJUSTMENT HINT: EM6 ADJUSTMENT EM11I01 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY

More information

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS 2000 Suzuki Truck Grand Vitara LTD JLS 2WD V6-2.5L Vehicle > Engine, Cooling and Exhaust > Engine > Specifications > Mechanical TORQUE SPECIFICATIONS Engine Torque Specifications TORQUE COMPONENT TIGHTENING

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are

More information

REMOVAL. 16. LOOSEN CRANKSHAFT PULLEY BOLT Using SST, loosen the pulley bolt. SST ( ), EM 20 SST TIMING BELT

REMOVAL. 16. LOOSEN CRANKSHAFT PULLEY BOLT Using SST, loosen the pulley bolt. SST ( ), EM 20 SST TIMING BELT EM20 REMOVAL EM11901 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY 5. REMOVE NO.2 CYLINDER HEAD COVER 6. REMOVE IGNITION COILS (See

More information

Timing Belt: Service and Repair Timing Belt Replace. Timing Belt Removal

Timing Belt: Service and Repair Timing Belt Replace. Timing Belt Removal 1998 Toyota Corolla DX Sedan 4-Door L4-1762cc 1.8L DOHC MFI Page 1 Timing Belt: Service and Repair Timing Belt Replace Timing Belt Removal SPECIAL SERVICE TOOL (SST) REQUIRED ^ 09213-70010 Crankshaft Pulley

More information

VALVE CLEARANCE (K3-VE)

VALVE CLEARANCE (K3-VE) ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT

More information

TIMING BELT COMPONENTS

TIMING BELT COMPONENTS EG134 3SGTE ENGINE TIMING BELT COMPONENTS 3SGTE ENGINE EG135 EG136 3SGTE ENGINE 3SGTE ENGINE TIMING BELT REMOVAL EG137 (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL

More information

TIMING BELT COMPONENTS EM 15

TIMING BELT COMPONENTS EM 15 ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work

More information

Fastener Tightening Specifications Specification

Fastener Tightening Specifications Specification 2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt

More information

TIMING BELT (5S FE) COMPONENTS

TIMING BELT (5S FE) COMPONENTS ENGINE MECHANICAL Timing Belt (5SFE) EM67 TIMING BELT (5SFE) COMPONENTS REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds

More information

OIL AND FILTER INSPECTION

OIL AND FILTER INSPECTION F 20 C 29 Recommended Viscosity (SAE): 0 18 20 7 5W30 40 4 60 16 80 27 LUBRICATION (2UZFE) 100 38 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE B16233 OIL AND FILTER OIL AND FILTER INSPECTION 1.

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.

REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration. 21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine

More information

EG1 485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION

EG1 485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION EG1485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION EG1486 EG1487 EG1488 OIL PUMP REMOVAL (See Components for Removal and Installation) HINT: When repairing the oil pump, the oil pan an^ strainer should

More information

INSTALLATION. NOTICE: Do not scratch the angle sensor of the timing pulley.

INSTALLATION. NOTICE: Do not scratch the angle sensor of the timing pulley. EM26 INSTALLATION EM11B01 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000, 0996300600) Torque:

More information

MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing.

MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. ST 499817100 ENGINE STAND Apply a coat of engine oil to the bearing and

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

2nd Timing Chain and Chain Tensioner Components S6RW0C

2nd Timing Chain and Chain Tensioner Components S6RW0C 8) Install cylinder head cover referring to Cylinder Head Cover Removal and Installation. 9) Install oil pan. Refer to Oil Pan and Oil Pump Strainer Removal and Installation in Section 1E for 10) Install

More information

CYLINDER HEAD (for Bank 2 4WD and Pre-Runner)

CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) 144 1GR-FE ENGINE MECHANICAL CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) ENGINE 1GR-FE ENGINE MECHANICAL COMPONENTS 88 (897, 65) x4 88 (897, 65) x4 NO. 1

More information

VALVE CLEARANCE (3MZ-FE)

VALVE CLEARANCE (3MZ-FE) ENGE MECHANICAL ADJUSTMENT. DRA ENGE COOLANT (See page ). REMOVE FR WIPER ARM LH (See page 7 ). REMOVE FR WIPER ARM RH (See page 7 ) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 7 ). REMOVE WDSHIELD

More information

TIMING BELT (4A FE) COMPONENTS

TIMING BELT (4A FE) COMPONENTS EM30 Timing Belt (4AFE) TIMING BELT (4AFE) COMPONENTS REMOVAL OF TIMING BELT 1. REMOVE RH FRONT WHEEL 2. REMOVE RH ENGINE UNDER COVER 3. REMOVE WASHER TANK 4. LOOSEN WATER PUMP PULLEY BOLTS AND REMOVE

More information

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: IS 350:

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: IS 350: TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: 2007 2008 IS 350: 2006 2008 I. OPERATION FLOWCHART Verify Vehicle Eligibility 1. Check the VIN range. 2.

More information

EM 38 2TR-FE ENGINE MECHANICAL CAMSHAFT REMOVAL

EM 38 2TR-FE ENGINE MECHANICAL CAMSHAFT REMOVAL 38 2TR-FE ENGINE MECHNICL CMSHFT ROVL 1. DISCONNECT CLE FROM NEGTIVE TTERY TERMINL 2. ROVE NO. 1 ENGINE UNDER COVER SU- SSLY (for 4WD) (a) Remove the 4 bolts, then remove the No. 1 engine under cover.

More information

3. Using the ST, align the Top mark on crank sprocket to nine o clock position as shown in the figure

3. Using the ST, align the Top mark on crank sprocket to nine o clock position as shown in the figure 2008 Tribeca (3.6L) MECHANICAL(H6DO) > Timing Chain Assembly Report a problem with this article INSTALLATION Be careful that the foreign matter is not into or onto assembled component during installation.

More information

EM 27 2UZ-FE ENGINE MECHANICAL CAMSHAFT REMOVAL

EM 27 2UZ-FE ENGINE MECHANICAL CAMSHAFT REMOVAL 2UZ-F NGIN MCHANICAL CAMSHAFT M 27 RMOVAL 1. RMOV TIMING BLT (See page M-18) 2. RMOV IGNITION COIL ASSMBLY (a) Disconnect the 4 ignition coil connectors. (b) Remove the 4 bolts and 4 ignition coils. 3.

More information

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43

More information

TIMING BELT (3S FE) COMPONENTS

TIMING BELT (3S FE) COMPONENTS Timing Belt (3SFE) TIMING BELT (3SFE) COMPONENTS EM23 REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY 2. REMOVE RH FRONT WHEEL 3. REMOVE ENGINE RH UNDER COVER 4. REMOVE CRUISE

More information

OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB ASSY

OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB ASSY 1416 OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUBASSY 140RL01. INSPECT CONNECTING ROD THRUST CLEARANCE (a) Using a dial indicator, measure the thrust clearance while moving the connecting rod

More information

1 of 12 11/20/2016 9:32 PM

1 of 12 11/20/2016 9:32 PM 1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing

More information

REMOVE FRONT WHEEL RH

REMOVE FRONT WHEEL RH 518 OVERHAUL POWER STEERING Do not overtighten when using a vise. When installing, coat the parts indicated by the arrows with power steering fluid (see page 517 ). 1. REMOVE FRONT WHEEL RH 2. DRAIN POWER

More information

4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)

4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].) TIMING CHAIN REMOVAL/INSTALLA... < Previous Next > 2007 Mazda3 Engine TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Remove the battery cover. 2. Disconnect the negative battery cable. 3. Remove the

More information

CO/HC INSPECTION HINT:

CO/HC INSPECTION HINT: CO/HC Meter CO/HC CO/HC INSPECTION HINT: EM1 EM03T03 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) Engine at normal operating

More information

OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder.

OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder. OVERHAUL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 40 times. HINT: When a pressure in power supply system is released, reaction force become

More information

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary. Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

More information

LUBRICATION SYSTEM (April, 2003)

LUBRICATION SYSTEM (April, 2003) SYSTEM (April, 2003) SYSTEM (April, 2003) ONVEHICLE INSPECTION 1. CHECK ENGINE OIL LEVEL (a) After warming up the engine and then 5 minutes after the engine stops, oil level should be between the L and

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil

More information

CO/HC INSPECTION HINT:

CO/HC INSPECTION HINT: ENGINE MECHANICAL (1MZFE) CO/HC Meter CO/HC CO/HC INSPECTION HINT: EM1 EM0I0 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) Engine

More information

CO/HC INSPECTION HINT:

CO/HC INSPECTION HINT: ENGINE MECHANICAL (2UZFE) CO/HC CO/HC INSPECTION HINT: EM1 EM0KQ09 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) Engine at normal

More information

EM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side

EM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side 112 Intake Air Surge Tank Side Cylinder Head Side 1GR-FE ENGINE MECHANICAL ENGINE ASSBLY INSPECTION 1. INSPECT INTAKE MANIFOLD FOR WARPAGE (a) Using a precision straight edge and feeler gauge, measure

More information

EM 84 ENGINE MECHANICAL (2RZ FE, 3RZ FE) EM16Y 02 DISASSEMBLY

EM 84 ENGINE MECHANICAL (2RZ FE, 3RZ FE) EM16Y 02 DISASSEMBLY EM84 ENGINE MECHANICAL (2RZFE, 3RZFE) EM16Y02 DISASSEMBLY 1. M/T: REMOVE FLYWHEEL Remove the 10 bolts and flywheel. 2. A/T: REMOVE DRIVE PLATE Remove the 10 bolts, front spacer, drive plate and rear plate.

More information

2AZ-FE Engine Oil Consumption Repair Procedure

2AZ-FE Engine Oil Consumption Repair Procedure S-SB-0024-11 Rev2 August 11, 2011 Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2007 2010 tc Engine(s): 2AZ VDS(s): DE167,

More information

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX)

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX) 2012 Cadillac CTS Wagon AWD V6-3.0L Vehicle > Engine, Cooling and Exhaust > Engine > Locations > Components DISASSEMBLED VIEWS Disassembled Views Engine Covers and Component Assemblies (1 of 2) (LF1, LFW

More information

75 5 ENGINE HOOD/DOOR

75 5 ENGINE HOOD/DOOR OVERHAUL Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. 755 750DN01 1. REMOVE

More information

INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B.

INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B. 8 CORRECT Adjusting Bar 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT Generator Vehicle Front A077960E03 INSTALLATION 1. INSTALL VANE PUMP V BELT (a) Temporarily install the belt on each pulley. 2. INSTALL

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information