OVERHAUL. HINT: COMPONENTS: FLOOR SHIFT ASSY (See page 40 35) 1. REMOVE CONSOLE BOX REAR COVER 2. REMOVE CONSOLE BOX CARPET
|
|
|
- Horace Morrison
- 5 years ago
- Views:
Transcription
1 4037 OVERHAUL COMPONENTS: FLOOR SHIFT ASSY (See page 4035) 1. REMOVE CONSOLE BOX REAR COVER 2. REMOVE CONSOLE BOX CARPET 4013O01 Front side of vehicle 3. REMOVE CONSOLE BOX SUBASSY REAR (a) Remove the console box subassy rear from the vehicle. C Adjust Lock Cap LeftSide Face: 4. DISCONNECT FLOOR SHIFT PARKING LOCK CABLE ASSY (a) Rotate the adjust lock cap clockwise by 90 facing the front of the vehicle, and release it. (b) Push the claw and disconnect the floor shift parking lock cable assy from the shift lock release link. Shift Lever Plate Shift Lock Release Link C89144 (c) Using a screw driver, disconnect the floor shift parking lock cable assy from the shift lever plate. C
2 4038 AUTOMATIC TRANSMISSION / TRANS RightSideFace: Shift Lever Plate 5. DISCONNECT TRANSMISSION CONTROL CABLE ASSY (a) Remove the nut, and disconnect the transmission control cable assy from the floor shift assy. (b) Using a screwdriver, disconnect the transmission control cable assy from the shift lever plate. C89145 Wire harness clamp 6. REMOVE FLOOR SHIFT ASSY (a) Disconnect the 2 connectors. (b) Remove the 2 wire harness clamps from the floor shift assy. (c) Remove the 4 bolts and floor shift assy. Wire harness clamp C REMOVE TRANSMISSION CONTROL SWITCH (a) Remove the connector from the shift lever plate. Connector D (b) (c) (d) Remove the transmission control switch connector from the shift lever plate. Disengage the secondary locking device. Release the locking lug of terminals 2 and 4, and then pull out the terminals from the rear. 1 2 Secondary Locking Device D
3 REMOVE SHIFT LEVER KNOB SUBASSY (a) Separate the wire harness of the transmission control switch from the shift lever plate. D29072 (b) Remove the 2 screws and shift lever knob subassy. NOTICE: Be careful not to apply excessive force to the Transmission control switch wire harness. (c) Remove the shift lever knob cover. (d) Remove the shift lever knob button and spring. (e) Remove the transmission control switch. Shift Lever Knob Subassy Shift Lever Knob Button Claws Spring Shift Lever Knob Cover Transmission Control Switch C89458 Shift Lock Release Button Cover Position Indicator Housing Upper Position Indicator Slide Cover Position Indicator Plate 9. REMOVE POSITION INDICATOR HOUSING UPPER (a) Remove the shift lock release button cover from the position indicator housing upper. (b) Remove the position indicator housing upper from the shift lever assy. (c) Remove the position indicator slide cover from the shift lever plate. (d) Remove the position indicator plate from the position indicator housing upper. C
4 4040 AUTOMATIC TRANSMISSION / TRANS Shift Lock Control Switch 10. REMOVE SHIFT LOCK CONTROL SWITCH (a) Remove the screw and shift lock control switch. Screw D REMOVE SHIFT LOCK SOLENOID (a) Remove the shift lock solenoid from the floor shift assy. Shift Lock Solenoid D REMOVE INDICATOR LAMP WIRE SUBASSY (a) Remove the indicator lamp wire subassy from the floor shift assy. Indicator Lamp Wire Subassy C89571 Shift Lock Release Button 13. REMOVE SHIFT LOCK RELEASE BUTTON (a) Remove the shift lock release button and spring from the floor shift assy. Spring D
5 4041 Spring Shift Lock Release Button D INSTALL SHIFT LOCK RELEASE BUTTON (a) Apply MP grease on the shift lock release button and spring. (b) Install the shift lock release button and spring to the floor shift assy. Ensure that the claws fit tightly. 15. INSTALL INDICATOR LAMP WIRE SUBASSY (a) Install the indicator lamp wire subassy to the floor shift assy. Indicator Lamp Wire Subassy C INSTALL SHIFT LOCK SOLENOID (a) Install the shift lock solenoid to the floor shift assy. Shift Lock Solenoid D29085 Shift Lock Control Switch Screw 17. INSTALL SHIFT LOCK CONTROL SWITCH (a) Install the shift lock control switch to the floor shift assy with the screw. Torque: 2.2 N m (22 kgf cm, 19 in. lbf) D
6 4042 AUTOMATIC TRANSMISSION / TRANS Shift Lock Release Button Cover Position Indicator Housing Upper Position Indicator Slide Cover Position Indicator Plate C INSTALL POSITION INDICATOR HOUSING UPPER (a) Install the position indicator plate on the position indicator housing upper. (b) Install the position indicator slide cover on the shift lever plate. (c) Install the position indicator housing upper on the shift lever assy. (d) Install the shift lock release button cover on the position indicator housing upper. 19. INSTALL TRANSMISSION CONTROL SWITCH (a) Apply MP grease to the shift lever knob button and spring. (b) Install the shift lever knob button and spring to the shift lever knob subassy. (c) Install the transmission control switch to the shift lever knob subassy. (d) Install the shift lever knob cover to the shift lever assy with the 2 screws. Coat the threads of screws with sealant. Sealant: Part No , THREE BOND 1344, LOCTITE 242 or equivalent NOTICE: Be careful not to catch the Transmission control switch wire harness. Ensure that the claws fit tightly claws. Shift Lever Knob Subassy MP grease Shift Lever Knob Button Claws Sealant Spring Sealant Shift Lever Knob Cover Transmission Control Switch C
7 INSTALL SHIFT LEVER KNOB SUBASSY (a) Install the 2 terminals into the indicator lamp wire connector. Secondary Locking Device C89577 (b) Clamp the wire harness and connector to the shift lever plate. Connector D29070 A C B Wire harness clamp 21. INSTALL FLOOR SHIFT ASSY (a) Install the floor shift assy with the 4 bolts. Torque: 12 N m (122 kgf cm, 9 ft lbf) Tighten them in the order, A, B, C and D. (b) Install the 2 wire harness clamps on the shift lever plate. D Wire harness clamp C89457 RightSideFace: 22. CONNECT TRANSMISSION CONTROL CABLE ASSY (a) Adjust the shift lever to the N position, push the lever to the R position side and hold it there. (b) While pulling the cable, connect the transmission control cable assy with the nut. Torque: 12 N m (122 kgf cm, 9 ft lbf) (c) Connect the 2 connectors. C
8 4044 AUTOMATIC TRANSMISSION / TRANS Casing Cap C CONNECT FLOOR SHIFT PARKING LOCK CABLE ASSY (a) Insert the floor shift parking lock cable end rod (ø4) in the slit of the shift lever plate. (b) Insert the casing cap of the cable into the shift lever plate throughhole. Check that it is inserted securely. LeftSide Face: (c) Insert the lever pin into the hole in the floor shift parking lock cable end. At this time, ensure that the shift lever is in the N position. After installation, make sure that the lever pin is pulled by the floor shift parking lock cable and is stopped with the stopper. C89573 Slide Cap (d) To check that the spring for automatic adjustment works properly, hold the slide cap and move it back and forth. C57978 (e) Rotate adjust lock cap shown in the illustration counterclockwise by 90 facing front of the vehicle. Install the floor shift parking lock cable on the shift lever side with the key in the ACC position. Make sure the slide amount of the spring for automatic adjustment is 8 mm (0.31 in.). Adjust Lock Cap C
9 INSPECT AND ADJUST SHIFT LEVER POSITION (a) Check that the starter operates when the shift lever is only the in P or N position and does not operate in other positions. (b) Operate the shift lever and check that the reading on the indicator conforms to the actual position. (c) Check that the ignition key can be pulled out with the shift lever in the P position. (d) Check that the ignition key cannot be turned to the LOCK position with the shift lever in any positions other than P. (e) Check that the shift lever can be shifted from the P position to other positions when the shift release button is depressed. 25. INSPECT SHIFT LEVER POSITION (Seepage 4046) 26. ADJUST SHIFT LEVER POSITION (Seepage 4046) Front Side of vehicle 27. INSTALL CONSOLE BOX SUBASSY REAR (a) Install the console box subassy to the vehicle. NOTICE: While installing the console box subassy, pay attention not to make defects on the shift lever knob and the indicator housing. C INSTALL CONSOLE BOX CARPET 29. INSTALL CONSOLE BOX REAR COVER 1295
FLOOR SHIFT ASSEMBLY
FLOOR SHIFT ASSEMBLY Components Removal 1. REMOVE THESE PARTS: a. Front door scuff plates b. Cowl side trim c. Lower finish panels d. Lower LH insert e. Lower instrument panel f. Lower RH panel g. Ash
5. SEPARATE STEERING INTERMEDIATE SHAFT ASSY (a) Fix the steering wheel with the seat belt. Release the 3 springs and separate the dust cover.
5119 OVERHAUL When installing, coat the parts indicated by the arrows with power steering fluid or molybdenum disulfide lithium base grease (See page 5116). 1. INSPECT CENTER FRONT WHEEL 510DA02 2. REMOVE
FLOOR SHIFT SHIFT LEVER ASSY (MTM)
4110 FLOOR SHIFT SHIFT LEVER ASSY (MTM) FLOOR SHIFT SHIFT LEVER ASSY (MTM) COMPONENTS 4105U03 Gasoline Engine: Front Floor Heat Insulator No.1 Console Panel Subassy Upper Floor Shift Lever Knob Subassy
OVERHAUL. NOTICE: Do not apply grease to each sliding part of the link. HINT: COMPONENTS: See page REMOVE REAR FLOOR FINISH PLATE
7528 ENGINE HOOD/DOOR OVERHAUL NOTICE: Do not apply grease to each sliding part of the link. COMPONENTS: See page 7526 7506701 1. REMOVE REAR FLOOR FINISH PLATE Using a screwdriver, remove the rear floor
OVERHAUL. 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Using a screwdriver, remove the lower frame bracket garnish.
OVERHAUL The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the RH side, use the same procedures as on the
75 5 ENGINE HOOD/DOOR
OVERHAUL Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. 755 750DN01 1. REMOVE
AUTOMATIC TRANSMISSION SYSTEM
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION SYSTEM PRECAUTION AUTOMATIC TRANSMISSION SYSTEM If the vehicle is equipped with a mobile communication system, refer to the precautions in the IN section.
SLIDING ROOF SYSTEM LOCATION. Sliding Roof Drive Gear Sub Assy (Include Sliding Roof Limit Switch)
/CONVERTIBLE SYSTEM 741 SYSTEM LOCATION 7405N02 Sliding Roof Drive Gear SubAssy (Include Sliding Roof Limit Switch) Sliding Roof Switch Assy (Include Power Window Relay) Sliding Roof Housing A65611 1815
2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS
2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When
OVERHAUL. 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit.
STARTING & CHARGING 195 OVERHAUL 190C702 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit. A57559 (b) (c) (d) Remove the 2 screws
REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.
14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
REPLACEMENT 1. REMOVE FRONT WHEEL
3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake
Symptom Suspect Area See page 5. Engine mounting (Loosen) 6. Clutch disc assy (Runout is excessive) 7. Clutch disc assy (Oily)
CLUTCH CLUTCH SYSTEM (MTM) PROBLEM SYMPTOMS TABLE HINT: CLUTCH SYSTEM (MTM) Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem.
REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
REAR DRUM BRAKE (1ZZ FE(FF))
REAR DRUM BRAKE (1ZZFE(FF)) OVERHAUL HINT: Overhaul the RH side by the same procedures as LH side. 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID NOTICE: Wash the brake fluid off immediately if it comes into
). 1. REMOVE FR WIPER ARM RH
5120 OVERHAUL When installing, apply power steering fluid or molybdenum disulfide lithium base grease to the parts indicated by arrows (See page 5117). 1. REMOVE FR WIPER ARM RH (See page 666) 2. REMOVE
OVERHAUL HINT: COMPONENTS: See page 74 49
7451 OVERHAUL COMPONENTS: See page 7449 7402R01 1. MOVE ROOF PANEL TO HALF Refer to the manual operation procedures, and halfopen the roof. H40336 A A:100 mm (3.94 in.) or less 2. REMOVE REAR SEAT CUSHION
2. DISCONNECT BATTERY NEGATIVE TERMINAL (See page 60 1) 3. REMOVE SHIFT LEVER KNOB SUB ASSY 4. REMOVE SHIFT LEVER KNOB SUB ASSY
7112 INSTRUMENT PANEL/METER 710DV02 REPLACEMENT HINT: COMPONENTS: See page 718 1. TABLE OF BOLT, SCREW AND NUT HINT: The bolts, screws and nuts, which are necessary for installation and removal of the
Code Shape Code Shape. φ = 6 (0.31) (0.24) (A) (B) (C) L = 18 L = 20 (0.71) φ = 5 (0.24) (0.20) (D) (E) (F) L = 16 L = 14 (0.63)
7110 INSTRUMENT PANEL/METER 7108S01 REPLACEMENT HINT: COMPONENTS: See page 717 1. TABLE OF BOLT, SCREW AND NUT HINT: Indicate the bolts, screws and nuts, which are necessary for installation and removal
SEAT BELT WARNING SYSTEM
WARNING SYSTEM LOCATION WARNING SYSTEM 611 6105001 Combination Meter (Driver s Seat Belt Warning Lamp) Clock Assy (Passenger s Seat Belt Warning Lamp) Seat Belt Warning Sensor Front Seat Inner Belt Assy
OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder.
OVERHAUL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 40 times. HINT: When a pressure in power supply system is released, reaction force become
REAR BUMPER COMPONENTS. Luggage Compartment. Trim Cover Assy RH. Rope Hook Assy. Deck Trim Side Board LH. Deck Trim Side Board RH.
767 COMPONENTS 7615701 Deck Trim Side Board LH Deck Trim Side Board RH Luggage Compartment Trim Cover Assy RH Luggage Compartment Floor Mat Luggage Compartment Trim Cover Assy LH Rear Floor Finish Plate
SHOCK ABSORBER ASSY FRONT LH
2612 REPLACEMENT COMPONENTS: See page 263 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. REMOVE FRONT WHEEL 260H802 2. SEPARATE FRONT STABILIZER
POWER STEERING SYSTEM
SYSTEM 511 SYSTEM PRECAUTION 5105K01 1. HANDLING PRECAUTIONS ON STEERING SYSTEM (a) Care must be taken to when replacing parts. Incorrect replacement could affect the performance of the steering system
V160 MANUAL TRANSMISSION MT2 1
MT21 MT22 V160 MANUAL TRANSMISSION PREPARATION SST (SPECIAL SERVICE TOOLS) 0930810010 Oil Seal Puller PREPARATION 0930814010 Replacer Pipe A 0930914040 Remover & Replacer D 0933000021 Companion Flange
REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2.
ENGINE MECHANICAL 1475 REPLACEMENT 141FV01 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. A66316 2. REMOVE IGNITION COIL NO.1 (a) Remove the 4 bolts and pull out
OVERHAUL. Using SST, disconnect the 2 brake tubes from the master cylinder. SST
3215 320J001 OVERHAUL 1. DRAIN BRAKE FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface. 2. REMOVE AIR CLEANER CAP SUBASSY 3. REMOVE (a) Disconnect the brake fluid
CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT
REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE
VALVE CLEARANCE (1NZ-FXE)
146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY
VALVE CLEARANCE (3ZZ FE/4ZZ FE)
ENGINE MECHANICAL ADJUSTMENT 1. REMOVE CYLINDER HEAD COVER NO.2 1487 140M901 Remove the 2 nuts, 2 clips and cylinder head cover. 2. REMOVE IGNITION COIL ASSY Disconnect the 4 connectors. (b) Remove the
10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.
14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE
2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE)
2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE) Vehicle» Steering and Suspension» Steering» Steering Gear» Service and Repair» Disassembly and Assembly Part 1 Of 3 Part 2 Of 3 http://alldatapro.com/alldata/pro~v432223842~c41100~r0~od~n/0/101825161/103142888/105946035/110859872/34853741/34864218/34864219/34864308/
REPLACEMENT. 12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 5 bolts, the engine moving control rod and the engine mounting stay.
1484 ENGINE MECHANICAL REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT WIPER ARM HEAD CAP 3. REMOVE FR WIPER ARM RH (See page 668 ) 4. REMOVE FR WIPER ARM LH (See page 668 ) 5. REMOVE COWL TOP VENTILATOR
REPLACEMENT. HINT: The installation procedures are the removal procedures in reverse order.
REPLACEMENT The installation procedures are the removal procedures in reverse order. 7615 7610301 1. REMOVE FRONT DOOR SCUFF PLATE RH (a) Using a screwdriver, disengage the 2 claws and 3 clips, and remove
7. MT Gear Shift Lever
7. A: REMOVAL 1. STI MODEL 1) Disconnect the ground cable from battery. 2) Remove the gear shift knob by turning it counterclockwise. 3) Remove the console box assembly.
POWER WINDOW CONTROL SYSTEM
POWER WINDOW CONTROL SYSTEM ONVEHICLE INSPECTION POWER WINDOW CONTROL SYSTEM 1. CHECK POWER WINDOW (MANUAL OPERATION FUNCTION) (a) Turn the ignition switch ON. (b) Check that the door glass will rise when
11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.
1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.
PARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
SERVICE DATA TRIMMER/BRUSHCUTTER KIORITZ CORPORATION F-00 SRM-260 SRM-261 Series 1
10-25F-00 SRM-260 SRM-261 Series 1 1 SERVICE DATA TRIMMER/BRUSHCUTTER SRM-260 (Serial number : 05001001~05999999) SRM-260S (Serial number : 05001001~05999999) SRM-260U (Serial number : 05001001~05999999)
FRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH
761 FRONT BUMPER FRONT BUMPER COMPONENTS 760HX02 Front Bumper Side Mounting Bracket RH Front Bumper Reinforcement 36 (367, 27) Front Bumper Side Mounting Bracket LH 36 (367, 27) 5.0 (51, 44 in. lbf) Front
10-25J-00 SRM-261T 1 INTRODUCTION. Reference No J-00 ISSUED:
10-25J-00 SRM-261T 1 1 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40L 2004 PRIUS BRAKE LIGHT SWITCH REPLACEMENT
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40L 2004 PRIUS BRAKE LIGHT SWITCH REPLACEMENT I. OPERATION FLOW CHART Verify Vehicle Eligibility 1. Check VIN range. 2. Check for SSC 40L Completion
SERVICE MANUAL SUPPLEMENT
21-63H-01 PB-770H, PB-770T 1 SERVICE MANUAL SUPPLEMENT 2 ECHO: PB-770H ECHO: PB-770T INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment
4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy.
OVERHAUL Refer to components: See page 304 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN TRANSAXLE OIL (a) Using a #10 socket hexagon wrench,
STARTING SYSTEM (1ZZ FE) (April, 2003)
STARTING & CHARGING STARTING SYSTEM (1ZZ FE) (April, 2003) STARTING SYSTEM (1ZZ FE) (April, 2003) INSPECTION 19 1 190QO 02 1. INSPECT STARTER ASSY NOTICE: These tests must be performed within 3 to 5 seconds
SERVICE DATA. SRM-230U (Serial number : ~ ) SRM-231U (Serial number : ~ ) TRIMMER/BRUSHCUTTER KIORITZ CORPORATION
10-22E-00 SRM-230 SRM-231 Series 1 1 SERVICE DATA TRIMMER/BRUSHCUTTER SRM-230 (Serial number : 05001001~05999999) SRM-230S (Serial number : 05001001~05999999) SRM-230U (Serial number : 05001001~05999999)
PS 23. POWER STEERING POWER STEERING LINK (for 2WD)
23 ZK08184E02 ZK08184E01 ZX09355E03 16. INSPECT TIE ROD END SUB-ASSEMBLY LH (a) Flip the ball joint stud back and forth 5 times as shown in the illustration, before installing the nut. (b) Using a torque
TOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT
Preparation Part Number: Mounting Kit PT546-06061 Tuner Assy 86180-0W030 Tuner Assy Kit Contents (86180-0W030) 1 1 Tuner Assy, Stereo Component Mounting Kit Contents (PT546-06061) 1 Ground Cable 1 1 Wire,
BRAKE E
8-1 GENERAL...8-2 SPECIFICATIONS...8-6 COMPONENTS...8-7 FRONT BRAKE...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn1, Cu2 3 TON SERIES)...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn2 3 TON SERIES)...8-17 BRAKE
Items Vehicles with 4G63 engine Vehicles with 4D56 engine. Type 4-speed full automatic 4-speed full automatic. 2nd rd
23-2 AUTOMATIC TRANSMISSION General Information/ Service Specifications GENERAL INFORMATION 23100010141 Items Vehicles with 4G63 engine Vehicles with 4D56 engine Transmission model R4AW2-6 V4AW2-6 Type
Symptom Suspect Area See page 1. Wire Harness or Connector 2. ECM 2. ECM. 1. Wire Harness or Connector 2. Skid control ECU 3. Combination Meter Assy
COMBINATION METER 711 COMBINATION METER PROBLEM SYMPTOMS TABLE Warning Lights and Buzzer: 7105L01 Symptom Suspect Area See page Check Engine warning light does not light up. 2. ECM 051, 05173 Discharge
7. Side Airbag Module
AIRBAG SYSTEM Side Airbag Module 7. Side Airbag Module A: REMOVAL Refer to CAUTION of General Description before handling the airbag module. NOTE: Remove
Installation instructions, accessories - Volvo Navigation System, widescreen
S60 Section Group Weight(Kg/Pounds) Year Month 3 39 2001 04 S60 2001, S60 2002 Page 1 of 21 Page 2 of 21 Required tools A0000162 A0000161 A0801178 M8802509 M3903563 Page 3 of 21 M3903565 M8503983 Page
PS 37. POWER STEERING POWER STEERING LINK (for 4WD) REMOVAL
POWER STEERING POWER STEERING LINK (for 4WD) 37 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 3. REMOVE FRONT WHEELS 4. REMOVE NO. 1 ENGINE UNDER
REPLACEMENT. 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FAN AND GENERATOR V BELT (See page 14 4)
5540 550JH01 REPLACEMENT HINT: COMPONENTS: See page 5539 1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM (See page 5511) SST 0711058060 (0711758080, 0711758090, 0711778050, 0711788060, 0711788070, 0711788080)
MANUAL TRANSMISSION Click on the applicable bookmark to selected the required model year
MANUAL TRANSMISSION 22-1 MANUAL TRANSMISSION CONTENTS LUBRICANT............................... 2 SEALANTS AND ADHESIVES.............. 2 ON-VEHICLE SERVICE..................... 2 Transmission Oil Check.......................
Front seats. Special tools and equipment. VAS 5094 airbag adapter. Connecting page 72-9.
Page 1 of 23 72-1 Front seats Special tools and equipment VAS 5094 airbag adapter Connecting page 72-9. Page 2 of 23 72-2 Front seats, removing and installing WARNING! Before starting work on seats, connect
TRANSFER ASSY (VF4AM)
ASSY (VF4AM) 313 ASSY (VF4AM) COMPONENTS 3103202 ATF Level Gauge Transmission Oil Filler Tube Subassy Propeller Shaft Assy 12 (122, 9) ORing Oil Cooler Inlet Tube No.1 and Oil Cooler Outlet Tube No.1 34
7-0 ENGINE REMOVAL 7. ENGINE REMOVAL/INSTALLATION MXU 500
7 ENGINE REMOVAL SERVICE INFORMATION------------------------------------------------ 7-1 ENGINE REMOVAL ------------------------------------------------------- 7-2 ENGINE INSTALLATION ------------------------------------------------
REMOVAL. 6. REMOVE LOWER FINISH PANEL Using a screwdriver, remove the lower finish panel. HINT: Tape the screwdriver tip before use.
BO90 REMOVAL 1. REMOVE FRONT SEATS (See page BO105 or BO1 12) 2. REMOVE FRONT DOOR WEATHERSTRIPS 3. REMOVE FRONT PILLAR GARNISHES 4. REMOVE STEERING WHEEL PAD (See page SR14 ) 5. REMOVE COLUMN COVERS BO2PV02
OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB ASSY
1416 OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUBASSY 140RL01. INSPECT CONNECTING ROD THRUST CLEARANCE (a) Using a dial indicator, measure the thrust clearance while moving the connecting rod
REMOVE FRONT WHEEL RH
518 OVERHAUL POWER STEERING Do not overtighten when using a vise. When installing, coat the parts indicated by the arrows with power steering fluid (see page 517 ). 1. REMOVE FRONT WHEEL RH 2. DRAIN POWER
Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket.
TIMING BELT (3MZFE) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FR WIPER ARM RH (See page 669) 3. REMOVE FR WIPER ARM LH (See page 669) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 669) 5.
FRONT AXLE HUB SUB-ASSY LH
3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)
COMPONENTS (KOYO Type)
STEERING SR55 COMPONENTS (KOYO Type) DISASSEMBLY OF STEERING GEAR HOUSING 1. CLAMP GEAR HOUSING IN VISE Using SST, secure the steering gear in a vise. SST 0961200012 2. REMOVE RIGHT AND LEFT TURN PRESSURE
2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS
2004 Toyota CAMRY Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS REPLACEMENT 1. REMOVE HOOD SU-ASSY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER
ENGINE ASSEMBLY COMPONENTS EM 170 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY V-BANK COVER VACUUM HOSE AIR CLEANER ASSEMBLY NO. 2 VENTILATION HOSE
170 ENGINE 1GR-FE MECHANICAL COMPONENTS 1GR-FE ENGINE MECHANICAL ENGINE 7.5 (76, 66 in.*lbf) V-BANK COVER 8.0 (82, 71 in.*lbf) 8.0 (82, 71 in.*lbf) VACUUM HOSE AIR CLEANER NO. 2 VENTILATION HOSE MASS AIR
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
14218 ENGINE MECHANICAL PARTIAL ENGINE ASSY (2ZZGE) OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 140R901 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
80-52A-00 EA Reference No A-00 ISSUED:
80-52A-00 EA-500 1 lntroduction We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications,
DRAIN BRAKE FLUID NOTICE:
OVERHAUL Overhaul procedure of the RH side is the same as that of with LH side. 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID Wash off the brake fluid immediately if it comes into contact with a painted surface.
Technical Service BULLETIN
Technical Service BULLETIN December 24, 1999 98 00 Sienna ST003 99 STEERING Introduction To provide a smoother steering return feeling, the steering rack guide has been changed. Applicable Vehicles 1998
DESCRIPTION. Exhaust Heat Recirculation System Circuit
Exhaust Heat Recirculation System Circuit DESCRIPTION In the exhaust heat recirculation system, coolant is warmed up using conventionally wasted exhaust gas heat to accelerate engine warm-up time, enhancing
CYLINDER HEAD GASKET (2AZ-FE)
190 REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 111 ) 2. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) 3. REMOVE CHAIN SUBASSY (See page
ON VEHICLE REPAIR Valve Body
AT28 AUTOMATIC TRANSMISSION ONVEHICLE REPAIR Valve Body REMOVAL OF VALVE BODY 1. CLEAN TRANSMISSION EXTERIOR To prevent contamination, clean the exterior of the trans mission. 2. DRAIN TRANSMISSION FLUID
PRECAUTION TROUBLESHOOTING
STEERING SR1 SR2 PRECAUTION Care must be taken to replace parts properly because they could affect the performance of the steering system and result in a driving hazard. The steering wheel pad has an SRS
ASX / OUTLANDER SPORT / RVR REAR VIEW CAMERA MZ380552EX INSTALLATION AND HANDLING INSTRUCTIONS
ASX / OUTLANDER SPORT / RVR REAR VIEW CAMERA MZ380552EX INSTALLATION AND HANDLING INSTRUCTIONS Navigation (MMCS) unit Camera Thank you for purchasing the Mitsubishi Genuine Accessory. To install and use
Installation instructions, accessories RTI S80
Installation instructions, accessories Instruction No 8685714 Version 1.0 5 Part. No. RTI S80 Volvo Car Corporation RTI S80-8685714 - V1.0 Page 1 / 25 Equipment A0000161 A0000162 A0801178 D8802049 Page
Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair
![Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair](/thumbs/86/93834005.jpg "Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair")
HMM180001 Brake System H1.5-1.8TX, H2.0TXS [B475]; H2.5-3.5TX [B466] Safety Precautions Maintenance and Repair When lifting parts or assemblies, make sure all slings, chains, or cables are correctly fastened,
ROOF HEADLINING ASSY EXTERIOR/INTERIOR TRIM 760VC 02 REPLACEMENT
REPLACEMENT 7627 The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the LH side, use the same procedures as
21-21H-00 PB-2100,PB-2155,PB-2200SI 1
21-21H-00 PB-2100,,PB-2200SI 1 2 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice.
Items Vehicles with 4G63 engine Vehicles with 4D56 engine. Type 5-speed, floor-shift 5-speed, floor-shift. 2nd rd
22-2 MANUAL TRANSMISSION General Information GENERAL INFORMATION 22100010113 Items Vehicles with 4G63 engine Vehicles with 4D56 engine Transmission model R5M21-5 R5M21-5 Type 5-speed, floor-shift 5-speed,
LUBRICATION SYSTEM (April, 2003)
SYSTEM (April, 2003) SYSTEM (April, 2003) ONVEHICLE INSPECTION 1. CHECK ENGINE OIL LEVEL (a) After warming up the engine and then 5 minutes after the engine stops, oil level should be between the L and
INDEX INTRODUCTION. Reference No L-01 REVISED:
12-21L-01 1 1 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications
www.clubsuprafrance.com CLUTCH 1996 Toyota Supra 1995-96 Clutch Supra DESCRIPTION The single, dry-type disc clutch uses a hydraulicallyoperated master cylinder with a clutch release cylinder mounted on
1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION
STEERING COLUMN - TILT
STEERING COLUMN - TILT 1993 Toyota Celica 1993 STEERING Toyota - Steering Columns - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate an upper steering shaft, attached by a "U"
Technical Service BULLETIN
Technical Service BULLETIN May 19, 2003 Title: Models: 00 02 Celica GTS EG010-03 ENGINE Introduction In some cases, owners of 2000 2002 model year Celica GTS vehicles equipped with the 2ZZ GE engine may
25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets.
CAMSHAFT (RH BANK) (2GRFE) REPLACEMENT 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE 1421) 2. REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE 1421) 4. REMOVE STARTER ASSY (SEE PAGE 199). REMOVE
PS 60. POWER STEERING POWER STEERING LINK (for 4WD and Pre-Runner) INSPECTION
60 ZK08184E01 INSPECTION 1. INSPECT TIE ROD END SUB-ASSEMBLY (a) Flip the ball joint stud back and forth 5 times as shown in the illustration before installing the nut. (b) Using a torque wrench, turn
00-33A-01 CS-330T, CS-360T 1
00-33A-01 CS-330T, CS-360T 1 0 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice.
IR 13 INTERIOR ROOF HEADLINING REMOVAL
INTERIOR ROOF HEADLINING 13 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH (See page SE-43) 3. REMOVE REAR SEATBACK ASSEMBLY RH (See page SE-43)
(c) Remove the solenoids.
ONVEHICLE REPAIR AT117 4. WHEN REPLACING 3 SOLENOIDS (a) Disconnect the connectors from the solenoids. (b) Remove the solenoid mounting bolts. Torque: 10 N m (100 kgf cm, 7 ft lbf) (c) Remove the solenoids.
11. ALTERNATOR/STARTER CLUTCH
11. ALTERNATOR/STARTER CLUTCH COMPONENT LOCATION 11-2 SERVICE INFORMATION 11-3 TROUBLESHOOTING 11-3 STATOR REMOVAL 11-4 FLYWHEEL/STARTER CLUTCH 11-6 STATOR INSTALLATION 11-12 11 11-1 ALTERNATOR/STARTER
SERVICE DATA TRIMMER/BRUSHCUTTER ECHO: SRM-236ES STAGE MODEL. (Serial number : and after) INTRODUCTION CONTENTS
10-21V-00 SRM-236ES 1 * 1 SERVICE DATA TRIMMER/BRUSHCUTTER ECHO: SRM-236ES STAGE MODEL (Serial number : 37000001 and after) INTRODUCTION We are constantly working on technical improvement of our products.
01-36D-02 CS INTRODUCTION. Reference No D-02 ISSUED:
01-36D-02 CS-370 1 0 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications,
Text in Illustration
ON-VEHICLE INSPECTION If using a dropper to adjust the fluid amount, make sure that the dropper has not been used with mineral oils, water or deteriorated brake fluid. Sealed areas may deteriorate and
DRAIN BRAKE FLUID NOTICE:
OVERHAUL Overhaul procedure of the RH side is the same as that of with LH side. 1. REMOVE FRONT WHEEL 2. DRAIN BRAKE FLUID Wash off the brake fluid immediately if it comes into contact with a painted surface.
ABBREVIATIONS USED IN THIS
IN10 INTRODUCTION ABBREVIATIONS USED IN THIS MANUAL ABBREVIATIONS USED IN THIS MANUAL ATF Automatic Transmission Fluid B 0 Overdrive Brake B 2 Second Brake B 3 No. 3 Brake C 0 Overdrive Direct Clutch C