FLOOR SHIFT SHIFT LEVER ASSY (MTM)
|
|
|
- Joel Morris
- 5 years ago
- Views:
Transcription
1 4110 FLOOR SHIFT SHIFT LEVER ASSY (MTM) FLOOR SHIFT SHIFT LEVER ASSY (MTM) COMPONENTS 4105U03 Gasoline Engine: Front Floor Heat Insulator No.1 Console Panel Subassy Upper Floor Shift Lever Knob Subassy 5.5 (56, 49 in. lbf) Console Box Carpet Console Panel Subassy Lower Console Box Subassy Rear Transmission Control Cable Assy 5.0 (51, 44 in. lbf) 12 (122, 9) 12 (122, 9) 5.0 (51, 44 in. lbf) N m (kgf cm, ft lbf) : Specified torque Floor Shift Shift Lever Assy D30489
2 FLOOR SHIFT SHIFT LEVER ASSY (MTM) REPLACEMENT 1. REMOVE FLOOR SHIFT SHIFT LEVER KNOB SUBASSY (See page 7111) 2. REMOVE CONSOLE PANEL UPPER (See page 7111) 3. REMOVE CONSOLE PANEL SUBASSY LOWER (See page 7111) 4. REMOVE CONSOLE BOX ASSY REAR (See page 7111) DR01 5. SEPARATE TRANSMISSION CONTROL CABLE ASSY (a) Remove the 2 clips, separate the cable ends of the control cable assy. D26893 (b) Release the claws, separate the control cable assy. D REMOVE FLOOR SHIFT SHIFT LEVER ASSY (a) Remove the 4 bolts and shift lever assy. D INSTALL FLOOR SHIFT SHIFT LEVER ASSY (a) Install the shift lever assy with the 4 bolts. Torque: 12 N m (122 kgf cm, 9 ft lbf) D30474
3 4112 FLOOR SHIFT SHIFT LEVER ASSY (MTM) 8. CONNECT TRANSMISSION CONTROL CABLE ASSY (a) Connect the control cable assy to the shift lever assy. Make sure that the claws are firmly engaged. D26972 Serrate Part (b) Connect the end of the select cable to the shift lever assy, install the clip. The serrate part of the select cable point should face upward when the select cable point is connected. The clip should be inserted to the direction as shown in the illustration. (c) Connect the end of the shift cable to the shift lever assy. D26894
4 FRONT DIFFERENTIAL OIL SEAL (C50/C250) FRONT DIFFERENTIAL OIL SEAL (C50/C250) REPLACEMENT 1. DRAIN MANUAL TRANSAXLE OIL Torque: 39 N m (400 kgf cm, 29 ft lbf) 2. REMOVE FRONT WHEELS 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT DRIVE SHAFT ASSY LH (See page 306) SST , ( ) 6. REMOVE FRONT DRIVE SHAFT ASSY RH (See page 306) SST , ( ) REMOVE TRANSAXLE CASE OIL SEAL (a) Using, remove the oil seal. SST C REMOVE TRANSMISSION CASE OIL SEAL (a) Using, remove the oil seal. SST D INSTALL TRANSAXLE CASE OIL SEAL (a) Coat a new oil seal lip with MP grease. (b) Using and a hammer, install the oil seal. SST , ( ) Drive in depth: mm ( in.) Be careful not to damage the oil seal lip. D25722
5 414 FRONT DIFFERENTIAL OIL SEAL (C50/C250) 10. INSTALL TRANSMISSION CASE OIL SEAL (a) Coat a new oil seal lip with MP grease. (b) Using and a hammer, install the oil seal. SST , ( ) Drive in depth: mm ( in.) Be careful not to damage the oil seal lip. D INSTALL FRONT DRIVE SHAFT ASSY LH (See page 306) 12. INSTALL FRONT DRIVE SHAFT ASSY RH (See page 306) 13. INSTALL FRONT WHEELS Torque: 103 N m (1,050 kgf cm, 76 ft lbf) 14. ADD MANUAL TRANSAXLE OIL Oil grade: API GL4 or GL5 Viscosity: SAE 75 W90 Capacity: 1.9 liters (2.0 US qts, 1.7 lmp. qts) Torque: 39 N m (400 kgf cm, 29 ft lbf) 0 to 5 mm (0 to 0.20 in.) D INSPECT MANUAL TRANSAXLE OIL (See page 412) 16. INSPECT FRONT WHEEL ALIGNMENT (See page 266) 17. CHECK ABS SPEED SENSOR SIGNAL (a) w/ VSC (See page 05756) (b) w/o VSC (See page 05699)
6 FRONT DIFFERENTIAL OIL SEAL (E354/E357) FRONT DIFFERENTIAL OIL SEAL (E354/E357) REPLACEMENT 1. DRAIN MANUAL TRANSAXLE OIL Torque: 49 N m (500 kgf cm, 36 ft lbf) 2. REMOVE FRONT WHEELS 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT DRIVE SHAFT ASSY LH (See page 306) SST , ( ) 6. REMOVE FRONT DRIVE SHAFT ASSY RH (See page 306) SST , ( ) REMOVE FRONT TRANSAXLE CASE COVER OIL SEAL (a) Using, remove the oil seal. SST C REMOVE TRANSMISSION CASE OIL SEAL (a) Using, remove the oil seal. SST D INSTALL FRONT TRANSAXLE CASE COVER OIL SEAL (a) Coat a new oil seal lip with MP grease. (b) Using and a hammer, install the oil seal. SST , ( ) Drive in depth: mm ( in.) Be careful not to damage the oil seal lip. D25722
7 416 FRONT DIFFERENTIAL OIL SEAL (E354/E357) 10. INSTALL TRANSMISSION CASE OIL SEAL (a) Coat a new oil seal lip with MP grease. (b) Using and a hammer, install the oil seal. SST , ( ) Drive in depth: mm ( in.) Be careful not to damage the oil seal lip. D INSTALL FRONT DRIVE SHAFT ASSY LH (See page 306) 12. INSTALL FRONT DRIVE SHAFT ASSY RH (See page 306) 13. INSTALL FRONT WHEELS Torque: 103 N m (1,050 kgf cm, 76 ft lbf) 14. ADD MANUAL TRANSAXLE OIL Oil grade: API GL4 or GL5 Viscosity: SAE 75 W90 Capacity: 2.5 liters (2.6 US qts, 2.2 lmp. qts) Torque: 49 N m (500 kgf cm, 36 ft lbf) 0 to 5 mm (0 to 0.20 in.) D INSPECT MANUAL TRANSAXLE OIL (See page 412) 16. INSPECT FRONT WHEEL ALIGNMENT (See page 266) 17. CHECK ABS SPEED SENSOR SIGNAL (a) w/ VSC (See page 05756) (b) w/o VSC (See page 05699)
8 4122 MANUAL TRANSAXLE ASSY (1AZFE/1AZFSE) MANUAL TRANSAXLE ASSY (1AZFE/1AZFSE) COMPONENTS 410DT01 13 (133, 10) Hood Subassy Air Cleaner Assy Engine Room Cover Side Radiator Support Opening Cover Battery Clamp Subassy 5.0 (51, 44 in. lbf) 5.0 (51, 44 in. lbf) 9.0 (92, 80 in. lbf) Battery 13 (131, 9) Battery Tray 40 (410, 30) Engine Cover Subassy No.1 Backup Lamp Switch Connector 46 (469, 34) 64 (653, 47) 26 (260, 19) 80 (816, 59) Transmission Control Cable Assy Transverse Engine Engine Mounting Insulator 64 (653, 47) 52 (530, 38) 44 (449, 32) Clutch Release Cylinder Assy 46 (469, 34) 18 (184, 13) 52 (530, 38) 8.4 (85, 74 in. lbf) 12 (120, 9) 13 (130, 9) 9.0 (92, 80 in. lbf) 44 (449, 32) Starter Connector N m (kgf cm, ft lbf) : Specified torque Nonreusable part 46 (469, 34) Starter Assy Manual Transaxle Assy 37 (380, 27) D30082
9 MANUAL TRANSAXLE ASSY (1AZFE/1AZFSE) 4123 Front Drive Shaft Assy RH 64 (650, 47) Front Drive Shaft Assy LH Snap Ring 64 (650, 47) Transverse Engine Engine Mounting Bracket Transverse Engine Engine Mounting Bracket 74 (755, 55) 64 (653, 47) 87 (887, 64) 64 (653, 47) Transverse Engine Engine Mounting Insulator 52 (530, 38) Cotter Pin 35 (360, 26) 64 (653, 47) 49 (500, 36) Cotter Pin 74 (755, 55) 49 (500, 36) 8.0 (82, 71 in. lbf) 89 (908, 66) Transverse Engine Engine Mounting Insulator 45 (459, 33) 133 (1,356, 83) 52 (530, 38) 89 (908, 66) 133 (1,356, 83) 216 (2,203, 159) 29 (296, 21) Engine Under Cover LH Engine Under Cover RH N m (kgf cm, ft lbf) : Specified torque Nonreusable part D30473
10 4124 MANUAL TRANSAXLE ASSY (1AZFE/1AZFSE) REPLACEMENT 1. INSPECT CENTER FRONT WHEEL 2. REMOVE COLUMN HOLE COVER SILENCER SHEET (See page 509) 3. SEPARATE STEERING INTERMEDIATE SHAFT ASSY NO.2 (See page 509) 4. REMOVE STEERING COLUMN HOLE COVER SUBASSY NO.1 (See page 509) 5. REMOVE STEERING INTERMEDIATE SHAFT (See page 509) 6. REMOVE FRONT WHEELS 7. REMOVE ENGINE UNDER COVER LH 8. REMOVE ENGINE UNDER COVER RH 9. DRAIN TRANSAXLE OIL Torque: 49 N m (500 kgf cm, 36 ft lbf) 10. REMOVE HOOD SUBASSY 11. REMOVE RADIATOR SUPPORT OPENING COVER 12. REMOVE ENGINE ROOM COVER SIDE 13. REMOVE ENGINE COVER SUBASSY NO REMOVE AIR CLEANER ASSY 15. REMOVE BATTERY CLAMP SUBASSY 16. REMOVE BATTERY 17. REMOVE BATTERY TRAY 410DU REMOVE BATTERY CARRIER (a) Remove the 4 bolts and battery carrier. D REMOVE STARTER ASSY (See page 1912) 20. SEPARATE WIRE HARNESS (a) Remove the 3 bolts, and separate the 3 wire harnesses. D30081
REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
OVERHAUL. NOTICE: Do not apply grease to each sliding part of the link. HINT: COMPONENTS: See page REMOVE REAR FLOOR FINISH PLATE
7528 ENGINE HOOD/DOOR OVERHAUL NOTICE: Do not apply grease to each sliding part of the link. COMPONENTS: See page 7526 7506701 1. REMOVE REAR FLOOR FINISH PLATE Using a screwdriver, remove the rear floor
OVERHAUL. HINT: COMPONENTS: FLOOR SHIFT ASSY (See page 40 35) 1. REMOVE CONSOLE BOX REAR COVER 2. REMOVE CONSOLE BOX CARPET
4037 OVERHAUL COMPONENTS: FLOOR SHIFT ASSY (See page 4035) 1. REMOVE CONSOLE BOX REAR COVER 2. REMOVE CONSOLE BOX CARPET 4013O01 Front side of vehicle 3. REMOVE CONSOLE BOX SUBASSY REAR (a) Remove the
LUBRICATION SYSTEM (April, 2003)
SYSTEM (April, 2003) SYSTEM (April, 2003) ONVEHICLE INSPECTION 1. CHECK ENGINE OIL LEVEL (a) After warming up the engine and then 5 minutes after the engine stops, oil level should be between the L and
PARTIAL ENGINE ASSY (2ZZ GE)
COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy
PARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
75 5 ENGINE HOOD/DOOR
OVERHAUL Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. 755 750DN01 1. REMOVE
05 15A MANUAL TRANSAXLE [F25M-R]
![05 15A MANUAL TRANSAXLE [F25M-R]](/thumbs/87/96820464.jpg "05 15A MANUAL TRANSAXLE [F25M-R]")
05 15A MANUAL TRANSAXLE [F25M-R] MANUAL TRANSAXLE [F25M-R] LOCATION INDEX................ 05 15A 1 TRANSAXLE OIL INSPECTION [F25M-R]............. 05 15A 2 TRANSAXLE OIL REPLACEMENT [F25M-R].......... 05
REPLACEMENT 1. REMOVE FRONT WHEEL
3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake
Code Shape Code Shape. φ = 6 (0.31) (0.24) (A) (B) (C) L = 18 L = 20 (0.71) φ = 5 (0.24) (0.20) (D) (E) (F) L = 16 L = 14 (0.63)
7110 INSTRUMENT PANEL/METER 7108S01 REPLACEMENT HINT: COMPONENTS: See page 717 1. TABLE OF BOLT, SCREW AND NUT HINT: Indicate the bolts, screws and nuts, which are necessary for installation and removal
PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque
ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)
Symptom Suspect Area See page 5. Engine mounting (Loosen) 6. Clutch disc assy (Runout is excessive) 7. Clutch disc assy (Oily)
CLUTCH CLUTCH SYSTEM (MTM) PROBLEM SYMPTOMS TABLE HINT: CLUTCH SYSTEM (MTM) Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem.
2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation
Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET
OVERHAUL. 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Using a screwdriver, remove the lower frame bracket garnish.
OVERHAUL The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the RH side, use the same procedures as on the
2. DISCONNECT BATTERY NEGATIVE TERMINAL (See page 60 1) 3. REMOVE SHIFT LEVER KNOB SUB ASSY 4. REMOVE SHIFT LEVER KNOB SUB ASSY
7112 INSTRUMENT PANEL/METER 710DV02 REPLACEMENT HINT: COMPONENTS: See page 718 1. TABLE OF BOLT, SCREW AND NUT HINT: The bolts, screws and nuts, which are necessary for installation and removal of the
REAR DRIVE SHAFT (3S GTE ENGINE)
SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,
OVERHAUL. Using SST, disconnect the 2 brake tubes from the master cylinder. SST
3215 320J001 OVERHAUL 1. DRAIN BRAKE FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface. 2. REMOVE AIR CLEANER CAP SUBASSY 3. REMOVE (a) Disconnect the brake fluid
2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS
2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When
TRANSFER ASSY (VF4AM)
ASSY (VF4AM) 313 ASSY (VF4AM) COMPONENTS 3103202 ATF Level Gauge Transmission Oil Filler Tube Subassy Propeller Shaft Assy 12 (122, 9) ORing Oil Cooler Inlet Tube No.1 and Oil Cooler Outlet Tube No.1 34
FRONT AXLE HUB SUB-ASSY LH
3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)
REPLACEMENT. 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FAN AND GENERATOR V BELT (See page 14 4)
5540 550JH01 REPLACEMENT HINT: COMPONENTS: See page 5539 1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM (See page 5511) SST 0711058060 (0711758080, 0711758090, 0711778050, 0711788060, 0711788070, 0711788080)
REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.
14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
5. SEPARATE STEERING INTERMEDIATE SHAFT ASSY (a) Fix the steering wheel with the seat belt. Release the 3 springs and separate the dust cover.
5119 OVERHAUL When installing, coat the parts indicated by the arrows with power steering fluid or molybdenum disulfide lithium base grease (See page 5116). 1. INSPECT CENTER FRONT WHEEL 510DA02 2. REMOVE
SHOCK ABSORBER ASSY FRONT LH
2612 REPLACEMENT COMPONENTS: See page 263 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. REMOVE FRONT WHEEL 260H802 2. SEPARATE FRONT STABILIZER
10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic
2005 XB OVERHAUL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 39 N m (398 kgf cm, 29 ft lbf)
FRONT SUSPENSION SYSTEM
SYSTEM PROBLEM SYMPTOMS TABLE SYSTEM Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part in order. If necessary,
FRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH
761 FRONT BUMPER FRONT BUMPER COMPONENTS 760HX02 Front Bumper Side Mounting Bracket RH Front Bumper Reinforcement 36 (367, 27) Front Bumper Side Mounting Bracket LH 36 (367, 27) 5.0 (51, 44 in. lbf) Front
CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT
REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE
4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy.
OVERHAUL Refer to components: See page 304 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN TRANSAXLE OIL (a) Using a #10 socket hexagon wrench,
DF 78. HINT: Face the rough side of the thrust washer marked by # to the differential case. INSPECTION
78 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) Face the rough side of the thrust washer marked by # to the differential case. INSPECTION 1. DIFFERENTIAL SIDE GEAR (w/ LSD Differential)
CYLINDER HEAD (for Bank 2 4WD and Pre-Runner)
144 1GR-FE ENGINE MECHANICAL CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) ENGINE 1GR-FE ENGINE MECHANICAL COMPONENTS 88 (897, 65) x4 88 (897, 65) x4 NO. 1
REAR SUSPENSION SYSTEM
SYSTEM PROBLEM SYMPTOMS TABLE SYSTEM Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part in order. If necessary,
REAR BUMPER COMPONENTS. Luggage Compartment. Trim Cover Assy RH. Rope Hook Assy. Deck Trim Side Board LH. Deck Trim Side Board RH.
767 COMPONENTS 7615701 Deck Trim Side Board LH Deck Trim Side Board RH Luggage Compartment Trim Cover Assy RH Luggage Compartment Floor Mat Luggage Compartment Trim Cover Assy LH Rear Floor Finish Plate
ENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B
22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS............................... 22A OVERHAUL..................... 22B 22A-2 GROUP 22A MANUAL TRANSAXLE CONTENTS GENERAL DESCRIPTION......... 22A-3 DIAGNOSIS 22A-6
OVERHAUL HINT: COMPONENTS: See page 74 49
7451 OVERHAUL COMPONENTS: See page 7449 7402R01 1. MOVE ROOF PANEL TO HALF Refer to the manual operation procedures, and halfopen the roof. H40336 A A:100 mm (3.94 in.) or less 2. REMOVE REAR SEAT CUSHION
10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.
14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE
OIL AND FILTER INSPECTION
F 20 C 29 Recommended Viscosity (SAE): 0 18 20 7 5W30 40 4 60 16 80 27 LUBRICATION (2UZFE) 100 38 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE B16233 OIL AND FILTER OIL AND FILTER INSPECTION 1.
SUSPENSION AND AXLE SA 1
SUSPENSION AND AXLE SA1 SA2 TROUBLESHOOTING SUSPENSION AND AXLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the
CYLINDER HEAD GASKET (2AZ-FE)
190 REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 111 ) 2. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) 3. REMOVE CHAIN SUBASSY (See page
REAR DIFFERENTIAL LOCATION INDEX
2007 DRIVELINE/AXLES Differential - MX-5 Miata REAR DIFFERENTIAL LOCATION INDEX Fig. 1: Identifying Location Of Rear Differential Components DIFFERENTIAL OIL INSPECTION 1. Park the vehicle on level ground
OIL PUMP (for 4WD and Pre-Runner)
1GR-FE BRICATION OIL PUMP (for 4WD and Pre-Runner) OIL PUMP (for 4WD and Pre-Runner) ENGINE 1GR-FE BRICATION COMPONENTS 23 88 (897, 65) 88 (897, 65) NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY FRONT PROPELLER
ENGINE ASSEMBLY COMPONENTS EM 170 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY V-BANK COVER VACUUM HOSE AIR CLEANER ASSEMBLY NO. 2 VENTILATION HOSE
170 ENGINE 1GR-FE MECHANICAL COMPONENTS 1GR-FE ENGINE MECHANICAL ENGINE 7.5 (76, 66 in.*lbf) V-BANK COVER 8.0 (82, 71 in.*lbf) 8.0 (82, 71 in.*lbf) VACUUM HOSE AIR CLEANER NO. 2 VENTILATION HOSE MASS AIR
V160 MANUAL TRANSMISSION MT2 1
MT21 MT22 V160 MANUAL TRANSMISSION PREPARATION SST (SPECIAL SERVICE TOOLS) 0930810010 Oil Seal Puller PREPARATION 0930814010 Replacer Pipe A 0930914040 Remover & Replacer D 0933000021 Companion Flange
1NZ-FE ENGINE CONTROL SYSTEM
PREPARATION 1NZ-FE ENGINE CONTROL SYSTEM 1NZ-FE ENGINE CONTROL SYSTEM PREPARATION SST 1 09817-33190 Sensor Socket Wrench 2 PREPARATION 1NZ-FE ENGINE CONTROL SYSTEM RECOMMENDED TOOLS 09082-00040 TOYOTA
2AZ-FE ENGINE CONTROL SYSTEM
PREPARATION 2AZ-FE ENGINE CONTROL SYSTEM 2AZ-FE ENGINE CONTROL SYSTEM PREPARATION SST 1 09817-33190 Sensor Socket Wrench Engine coolant temperature sensor 2 PREPARATION 2AZ-FE ENGINE CONTROL SYSTEM RECOMMENDED
REMOVE FRONT WHEEL RH
518 OVERHAUL POWER STEERING Do not overtighten when using a vise. When installing, coat the parts indicated by the arrows with power steering fluid (see page 517 ). 1. REMOVE FRONT WHEEL RH 2. DRAIN POWER
Supercharged MK1 MR2 Part Diagrams
Supercharged MK1 MR2 Part Diagrams Created by: Charles K. (ckowalc) 1 Table of Contents PART DIAGRAM PAGE ACCELERATOR LINK 9 AIR CLEANER 10 AIR CLEANER 4AGZE 11 ALTERNATOR 4AGZE 12 ANTENNA 13 ARMREST &
OIL AND FILTER INSPECTION
F 20 C 29 Recommended Viscosity (SAE): 0 18 20 7 5W30 40 4 60 16 80 27 100 38 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE B16233 OIL AND FILTER OIL AND FILTER INSPECTION 1. CHECK OIL QUALITY LU1
POWER STEERING SYSTEM
SYSTEM 511 SYSTEM PRECAUTION 5105K01 1. HANDLING PRECAUTIONS ON STEERING SYSTEM (a) Care must be taken to when replacing parts. Incorrect replacement could affect the performance of the steering system
Symptom Suspect Area See page 1. Wire Harness or Connector 2. ECM 2. ECM. 1. Wire Harness or Connector 2. Skid control ECU 3. Combination Meter Assy
COMBINATION METER 711 COMBINATION METER PROBLEM SYMPTOMS TABLE Warning Lights and Buzzer: 7105L01 Symptom Suspect Area See page Check Engine warning light does not light up. 2. ECM 051, 05173 Discharge
AUTOMATIC TRANSMISSION SYSTEM
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION SYSTEM PRECAUTION AUTOMATIC TRANSMISSION SYSTEM If the vehicle is equipped with a mobile communication system, refer to the precautions in the IN section.
Printed from CyberCat-STIGA Section: GARDEN ELECTRICAL SYSTEM
Section: GARDEN ELECTRICAL SYSTEM Section: GARDEN ELECTRICAL SYSTEM 2312 2333 1 1 1134-3625-01 Harness 2 1 1134-3623-02.Interlock module 4 2 9849-8013-16 Screw 5 2 1134-3132-01 Cable holder 6 2 1134-3204-01
REMOVAL. 6. REMOVE LOWER FINISH PANEL Using a screwdriver, remove the lower finish panel. HINT: Tape the screwdriver tip before use.
BO90 REMOVAL 1. REMOVE FRONT SEATS (See page BO105 or BO1 12) 2. REMOVE FRONT DOOR WEATHERSTRIPS 3. REMOVE FRONT PILLAR GARNISHES 4. REMOVE STEERING WHEEL PAD (See page SR14 ) 5. REMOVE COLUMN COVERS BO2PV02
1GR-FE ENGINE CONTROL SYSTEM
PREPARATION 1GR-FE ENGINE CONTROL SYSTEM 1GR-FE ENGINE CONTROL SYSTEM PREPARATION RECOMMENDED TOOLS 1 09040-00011 Hexagon Wrench Set (09043-20080) Socket Hexagon Wrench 8 (09043-20100) Socket Hexagon Wrench
Hornet /Wasp / Spyder Fig. 1
Hornet /Wasp / Spyder Fig. 1 1 30A o Q v Hornet / Wasp/ Spyder Fig. 1 ITEM QUANTITY PART NO DESCRIPTION 1 4 4 4 9997.0890-12 Screw 2 17 17 17 9747.0831-02 Lock Nut 3 2 2 2 1134.3165-01 Tube Plate 4 2 2
OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder.
OVERHAUL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 40 times. HINT: When a pressure in power supply system is released, reaction force become
If it exceeds the maximum specification, replace the propeller shaft.
If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown
). 1. REMOVE FR WIPER ARM RH
5120 OVERHAUL When installing, apply power steering fluid or molybdenum disulfide lithium base grease to the parts indicated by arrows (See page 5117). 1. REMOVE FR WIPER ARM RH (See page 666) 2. REMOVE
SLIDING ROOF SYSTEM LOCATION. Sliding Roof Drive Gear Sub Assy (Include Sliding Roof Limit Switch)
/CONVERTIBLE SYSTEM 741 SYSTEM LOCATION 7405N02 Sliding Roof Drive Gear SubAssy (Include Sliding Roof Limit Switch) Sliding Roof Switch Assy (Include Power Window Relay) Sliding Roof Housing A65611 1815
SA 66 Front Differential (Disassembly and Assembly of Differential w/o A D D ) Disassembly and Assembly of Differential (with out A.D.D.
SA66 SUSPENSION AND AXLE Differential w/o A D D ) Disassembly and Assembly of Differential (with out A.D.D.) SUSPENSION AND AXLE Differential w/o A D D ) DISASSEMBLY OF DIFFERENTIAL 1. REMOVE DIFFERENTIAL
POWER WINDOW CONTROL SYSTEM
POWER WINDOW CONTROL SYSTEM ONVEHICLE INSPECTION POWER WINDOW CONTROL SYSTEM 1. CHECK POWER WINDOW (MANUAL OPERATION FUNCTION) (a) Turn the ignition switch ON. (b) Check that the door glass will rise when
MANUAL TRANSMISSION CONTENTS
22-1 MANUAL TRANSMISSION CONTENTS 22109000319 LUBRICANT... 2 SPECIAL TOOLS... 2 ON-VEHICLE SERVICE... 3 Transmission Oil Check... 3 Transmission Oil Replacement... 3 TRANSMISSION CONTROL*... 4 TRANSMISSION
DIAGNOSTICS PREPARATION SST. Recomended Tools Oil Pressure Switch Socket SFI SYSTEM Diagnosis Check Wire No.
DIAGNOSTICS SST DIAGNOSTICS 021 021CL01 0981630010 Oil Pressure Switch Socket SFI SYSTEM 0984318040 Diagnosis Check Wire No.2 SFI SYSTEM SUPPLEMENTAL SYSTEM RESTRAINT Recomended Tools 0908200040 TOYOTA
Technical Service BULLETIN
Technical Service BULLETIN September 16, 2002 Title: Models: 01 02 Sequoia BR005-02 BRAKES TSB REVISION NOTICE: March 5, 2004: A torque specification on page 9, step 24, was changed. September 8, 2003:
ABBREVIATIONS USED IN THIS MANUAL
IN6 INTRODUCTION Abbreviations Used in This Manual ABBREVIATIONS USED IN THIS MANUAL A/T ATM Automatic Transmission ATF Automatic Transmission Fluid B 0 Overdrive Brake B 1 Second Coast Brake B 2 Second
DF 15. DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) REMOVAL
DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) 15 REMOVAL 1. REMOVE FRONT WHEELS 2. REMOVE REAR ENGINE UNDER COVER ASSEMBLY (a) Remove the 6 bolts and engine under cover assembly. 3.
FLOOR SHIFT ASSEMBLY
FLOOR SHIFT ASSEMBLY Components Removal 1. REMOVE THESE PARTS: a. Front door scuff plates b. Cowl side trim c. Lower finish panels d. Lower LH insert e. Lower instrument panel f. Lower RH panel g. Ash
Symptom Suspect Area See page. 3. Shock absorber (Worn out) 3. Shock absorber (Worn out)
TROUBLESHOOTING PROBLEM SYMPTOMS TABLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part
MANUAL TRANSMISSION Click on the applicable bookmark to selected the required model year
MANUAL TRANSMISSION 22-1 MANUAL TRANSMISSION CONTENTS LUBRICANT............................... 2 SEALANTS AND ADHESIVES.............. 2 ON-VEHICLE SERVICE..................... 2 Transmission Oil Check.......................
1. General Description
1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh
TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN ESD * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN ESD * * * * * * * * * * * * * * * * * * * * * * * * * * * * * CERTAIN 2005 THROUGH 2008 MODEL YEAR TACOMA * * * * * * * * * * * * * * * * * * * * * *
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.
Page 1 of 12 Last Modified: 9-21-2007 1.6 A Service Category: Vehicle Interior Section: Interior Panels/Trim Model Year: 2008 Model: Tundra Doc ID: RM000002VHU003X Title: INSTRUMENT PANEL: INSTRUMENT PANEL
1. General Description
1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final
03 1 SERVICE SPECIFICATIONS
SERVICE SPECIFICATIONS STANDARD BOLT STANDARD BOLT HOW TO DETERMINE BOLT STRENGTH 031 0307K02 Bolt Type Hexagon Head Bolt Normal Recess Bolt Deep Recess Bolt Stud Bolt Weld Bolt Class 4 4T No Mark No Mark
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT
REAR DRUM BRAKE (1ZZ FE(FF))
REAR DRUM BRAKE (1ZZFE(FF)) OVERHAUL HINT: Overhaul the RH side by the same procedures as LH side. 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID NOTICE: Wash the brake fluid off immediately if it comes into
AUTOMATIC TRANSMISSION FLUID (A750E/A750F)
404 AUTOMATIC TRANSMISSION / TRANS ADJUSTMENT 4017G02 1. BEFORE FILLING TRANSMISSION This transmission requires Toyota Genuine ATF WS. It is necessary to refill the transmission with the correct amount
OPERATION AT-2. Clutch No.3 (C 3 ) Clutch No.1 (C 1 ) One-way Clutch
AT2 OPERATION AT13K01 Clutch No.3 (C 3 ) Clutch No.1 (C 1 ) Clutch No.2 (C 2 ) Oneway Clutch No.2 (F 2 ) Brake No.3 (B 3 ) Oneway Clutch No.1 (F 1 ) Brake No.1 (B 1 ) Brake No.2 (B 2 ) Oneway Clutch No.3
6-2.REAR DIFFERENTIAL REAR DRIVE (REAR DIFFERENTIAL) A:4.2~4.4 kgf-m B:3.0~3.5 kgf-m C:0.7~0.9 kgf-m D:2.0~2.2 kgf-m E F:1.2~1.5 kgf-m G: 11~12kgf-m
6-2.REAR DIFFERENTIAL REAR DRIVE (REAR DIFFERENTIAL) A:4.2~4.4 kgf-m B:3.0~3.5 kgf-m C:0.7~0.9 kgf-m D:2.0~2.2 kgf-m E F:1.2~1.5 kgf-m G: 11~12kgf-m 6-2-1 6-2. REAR DIFFERENTIAL REAR DIFFERENTIAL REMOVAL
22A-1 CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B o00111
MANUAL TRANSAXLE OVERHAUL................. 22B 22A-1 CONTENTS 22109o00111 MANUAL TRANSAXLE............................. 22A ~ TRAN AXLE CONTENTS 22109000180 GENERAL INFORMATION....3 SPECIAL TOOLS....6
MANUAL TRANSMISSION CONTENTS
22-1 MANUAL TRANSMISSION CONTENTS GENERAL INFORMATION.................. 2 LUBRICANTS.............................. 2 SEALANT.................................. 2 SPECIAL TOOLS...........................
www.clubsuprafrance.com CLUTCH 1996 Toyota Supra 1995-96 Clutch Supra DESCRIPTION The single, dry-type disc clutch uses a hydraulicallyoperated master cylinder with a clutch release cylinder mounted on
Oil Pan Seal Cutter Oil Filter Wrench Transmission & Transfer Bearing Replacer. ( ) Replacer Pipe
EG359 PREPARATION SST (SPECIAL SERVICE TOOLS) 0903200100 Oil Pan Seal Cutter No.2 oil pan 0922807500 Oil Filter Wrench 0931660010 Transmission & Transfer Bearing Replacer (0931600010) Replacer Pipe Crankshaft
ENGINE SPECIFICATIONS
ENGINE SPECIFICATIONS MECHANICAL LOCATION INDEX Engine cover 1 (See ENGINE COVER REMOVAL/INSTALLATION.) 2 Drive belt Page 1 (See DRIVE BELT DEFLECTION/TENSION INSPECTION.) (See DRIVE BELT ADJUSTMENT.)
MR2 U SECTION 8 SPECIFICATIONS. Dimensions and weight Service specifications MR2 (OM17475U)
SPECIFICATIONS SECTION 8 Dimensions and weight...................................... 192 Engine.................................................... 192 Fuel.......................................................
VALVE CLEARANCE (3MZ-FE)
ENGE MECHANICAL ADJUSTMENT. DRA ENGE COOLANT (See page ). REMOVE FR WIPER ARM LH (See page 7 ). REMOVE FR WIPER ARM RH (See page 7 ) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 7 ). REMOVE WDSHIELD
VALVE CLEARANCE (1NZ-FXE)
146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY
Part 8 SPECIFICATIONS
Part 8 SPECIFICATIONS Dimensions and weight Engine Fuel Service specifications Tires Fuses Dimensions and weight P195/70R 14 tire Overall length 4783 (188.3) Overall width 1780 (70.1) Overall height 1416
REAR AXLE AND SUSPENSION RA 1
REAR AXLE AND SUSPENSION RA1 RA2 REAR AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated Replace tires or inflate to
SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE
SA1 SA2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Front Page Rear Wanders/pulls Tires worn or improperly inflated Wheel alignment incorrect Hub bearing worn Front or rear suspension
OVERHAUL. 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit.
STARTING & CHARGING 195 OVERHAUL 190C702 1. REMOVE REPAIR SERVICE STARTER KIT (a) Remove the nut, and disconnect the lead wire from the repair service starter kit. A57559 (b) (c) (d) Remove the 2 screws
Printed from CyberCat-STIGA Section: VILLA ACCESSORY BAG
Section: VILLA ACCESSORY BAG Section: VILLA ACCESSORY BAG Pos. Quantity Spare part No Description Kit Notes New 2721 2722 2723 2724 0 1 1134-4664-01 Accessory bag assy 1 1 9595-0262-00.Locating pin 2A
A 1 SERVICE SPECIFICATIONS
A1 A2 Clutch CLUTCH Specifications Pedal height (from asphalt sheet) Release point (from pedal stroke end position) Push rod play at pedal top Pedal freeplay Disc rivet head depth Disc runout Diaphragm
MANUAL TRANSAXLE Return to Main Table of Contents
MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER
ED 42. ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window)
42 ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window) (g) (h) Horizontally and vertically adjust the door by loosening the door side hinge bolts. Tighten the door side hinge bolts after the adjustment. Torque:
FRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR
FRONT DRIVE SHAFT DRIVE LINE SHAFT COMPONENTS 1 FRONT DRIVE SHAFT HOLE SNAP RING 23 (235, 17) FRONT DRIVE SHAFT ASSEMBLY RH w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT ASSEMBLY LH
BRAKE E
8-1 GENERAL...8-2 SPECIFICATIONS...8-6 COMPONENTS...8-7 FRONT BRAKE...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn1, Cu2 3 TON SERIES)...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn2 3 TON SERIES)...8-17 BRAKE
ROOF HEADLINING ASSY EXTERIOR/INTERIOR TRIM 760VC 02 REPLACEMENT
REPLACEMENT 7627 The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the LH side, use the same procedures as
Item P/N Description MSRP 1 TS250-B01.01 Handlebar >
TS 250cc TNG SCOOTER Item P/N Description MSRP 1 TS250-B01.01 Handlebar 132.77 --> 3 TS250-B01.03 Throttle cable 22.55 --> 7 TS250-B01.07 Cable Seat 1.98 --> 8 TS250-B01.08 Grip, Right 7.04 --> 9 TS250-B01.09