1 of 8 10/22/2015 3:08 PM
|
|
- Dana Knight
- 5 years ago
- Views:
Transcription
1 1 of 8 10/22/2015 3:08 PM WM Removing and installing oil mist separator on 4.8-liter DFI engines Preliminary work Preliminary work 1. Remove design cover of bar ignition modules and throttle valve. Information Component overview Oil mist separator for positive crankcase ventilation (M48/51 turbo engine) 1 - Engine ventilation - Tightening torque: 10 Nm (7.5 ftlb.) 2 - Engine ventilation line 3 - Tank ventilation 4 - Holder - Tightening torque: 13 Nm (9.5 ftlb.)
2 2 of 8 10/22/2015 3:08 PM Oil mist separator for positive crankcase ventilation (M48/01 naturally aspirated engine) 1 - Engine ventilation - Tightening torque: 10 Nm (7.5 ftlb.) 2 - Engine ventilation line 3 - Screw, M6 x 12 - Tightening torque: 10 Nm (7.5 ftlb.) 4 - Lid with seal 5 - Engine ventilation line 6 - Line 7 - Tank ventilation with holder - Tightening torque: 13 Nm (9.5 ftlb.) Oil mist separator and gaskets on V8 S Oben - Oil mist separator for cylinder bank 5 to 8 Unten - Oil mist separator for cylinder bank 1 to Flange gaskets 2 - Sealing rings on connection piece 3 - Flange gaskets Removing oil mist separator Removing oil mist separator Cylinder bank 1 to 4 1. Disconnect cable connection on the connection piece for the oil mist separator -1-. Check sealing ring and replace it if necessary.
3 3 of 8 10/22/2015 3:08 PM Oil mist separator for cylinder bank 1 to 4 2. Loosen both screws -2-. Screws are permanently connected. If screws are damaged, press the screws out of the oil mist separator and replace them. 3. Hold oil mist separator at the left and right and pull carefully out of the bore in the valve cover by joggling it. At the same time check the gaskets and replace them if damaged. Cylinder bank 5 to 8 4. Disconnect cable connections to the connection piece on the oil mist separator: Naturally aspirated engine -1 and 2-, Turbo engine -arrows-. Check sealing ring and replace it if necessary. Oil mist separator for cylinder bank 5 to 8 on V8 S
4 4 of 8 10/22/2015 3:08 PM Oil mist separator for cylinder bank 5 to 8 on V8 Turbo 5. Loosen both screws -3-. Screws are permanently connected. If screws are damaged, press the screws out of the oil mist separator and replace them. 6. Hold oil mist separator at the rear and pull carefully out of the bore in the valve cover by joggling it. At the same time check the gaskets and replace them if damaged. Lift carefully, as the oil return line is still fitted. Removing oil mist separator
5 5 of 8 10/22/2015 3:08 PM Detaching oil mist separator at front 7. Detach oil return line underneath the oil mist separator at the plastic connection piece -arrow-. Loosen spring band clamp if necessary (Turbo) -arrow-. Oil return on V8 S
6 6 of 8 10/22/2015 3:08 PM Oil return on V8 Turbo Installing oil mist separator Installing oil mist separator The installation procedure for cylinder banks 1 to 4 and 5 to 8 is essentially the same. 1. Check gaskets on oil mist separator and replace if damaged. -1, 2 and 3- Oil mist separator and gaskets on V8 Oben - Oil mist separator for cylinder bank 5 to 8 Unten - Oil mist separator for cylinder bank 1 to Flange gaskets 2 - Sealing rings on connection pieces 3 - Flange gaskets
7 7 of 8 10/22/2015 3:08 PM 2. Lubricate sealing rings on connection piece on oil mist separator with grease (Kluber Syntheso Glep 1) Place oil mist separator in installation position. 4. Fit oil return line underneath the oil mist separator on the plastic connection piece -arrow-. Fit spring band clamp if necessary (Turbo) -arrow-. Oil return on V8 S Oil return on V8 Turbo 5. Place oil mist separator uniformly and carefully onto the valve cover using both hands. Press connection piece of oil mist separator into bore in valve cover. 6. Screw in and tighten screws for oil mist separator -3-. Screws are permanently connected. If screws are damaged, press the screws out of the oil mist separator and replace them. - Tightening torque: 10 Nm (7.5 ftlb.) 7. Fit cable connections to the connection piece on the oil mist separator: Naturally aspirated engine -1 and 2-, Turbo engine -arrows-. Check sealing ring and replace it if necessary.
8 8 of 8 10/22/2015 3:08 PM Oil mist separator for cylinder bank 5 to 8 on V8 S Oil mist separator for cylinder bank 5 to 8 on V8 Turbo Subsequent work Subsequent work 1. Fit design cover ALLDATA, LLC. All Rights Reserved. (Version )
1 of 27 7/21/2015 3:33 PM
1 of 27 7/21/2015 3:33 PM WM 489819 Removing and installing hydraulic pump - as of model year 2009 Tools Technical values Information 2 of 27 7/21/2015 3:33 PM Overview of hydraulic pump Preliminary work
More informationREMOVING CYLINDER HEAD COVER (VALVE COVER) - AS OF MY 2004 (CAYENNE TIP, CAYENNE MAN) > PRELIMINARY WORK > PRELIMINARY WORK
Page 1 of 9 CYLINDER HEAD, VALVE DRIVE 15 82 21 REMOVING CYLINDER HEAD COVER (VALVE COVER) - AS OF MY 2004 (CAYENNE TIP, CAYENNE MAN) > PRELIMINARY WORK > PRELIMINARY WORK 1. Remove engine compartment
More informationToothed belt, removing and installing
Toothed belt, removing and installing Special Tools and Equipment ^ 3212 spanner wrench ^ 3387 pin wrench ^ T40011 pin ^ T40026 locking pin ^ T40028 socket ^ T40030 camshaft adjuster gauge Removing Lock
More information1 of 13 10/12/2013 2:20 PM
1 of 13 10/12/2013 2:20 PM Coolant Pump, 4-cyl. Warning: Take care if the car is warm. The coolant is hot and there is also a risk of burning yourself on the manifold. To Remove 1. Open the cap on the
More information2006 Porsche Cayenne
Fig. 21: Releasing front wheel housing liner (2 Of 2) 3. Unscrewing fastening screws 3.1. Lift wheel housing liner -8- in the lower area. See Fig. 21. 3.2. Undo fastening screws -4, 6-. See Fig. 21. Fig.
More informationPage 1 of 6 Section 03-01C: Engine 3.4L SHO 1999 Taurus/Sable Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/25/1998 Intake Manifold Upper Removal 1. Disconnect battery ground cable (14301).
More information1 of 25 9/12/2013 9:07 PM
1 of 25 9/12/2013 9:07 PM 46RE Automatic Transmission DISASSEMBLY 1. Clean exterior of transmission with suitable solvent or pressure washer. 2. Place transmission in vertical position. 3. Measure the
More information1 of 2 5/25/17, 4:57 PM
1 of 2 5/25/17, 4:57 PM Overview - Bumper Cover, Audi Q5 S-Line and Audi SQ5 If the vehicle has lane change assistance, the lane change assistance control module (J769) / (J770) must be recalibrated. 1
More informationINSTALLING AND REMOVING THE HEATING/AIR-CONDITIONING UNIT
INSTALLING AND REMOVING THE HEATING/AIR-CONDITIONING UNIT REMOVAL 1. Remove the covers over the heating/air-conditioning system, battery and fluid tank. Disconnect and remove the battery. 2. Remove the
More information2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing
1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement
More information2001 Dodge Pickup R2500
FUEL INJECTION PUMP Removal CAUTION: High-pressure fuel lines must be clamped securely and routed so they do not contact each other or any other components. DO NOT weld or switch high-pressure fuel lines.
More information1 of 2 5/17/17, 1:22 PM
1 of 2 5/17/17, 1:22 PM Trim Molding, Removing and Installing Special tools, testers and auxiliary items required Wedge Set (T10383) Removal Wedge (T40233) Removing - Starting at the front, pry the trim
More informationCylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
More information1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
More informationWM Changing ATF
Page 1 of 7 The present document was valid at the time of print. A later version may be available online WM 370255 Changing ATF Tools Designation Type Number Description Screw connection hose Special tool
More informationTIMING BELT REMOVAL/INSTALLATION [ZM]
ALLDATA Online - 2000 Mazda Protege LX L4-6L DOHC - Service an... 1 of 8 6/26/2012 7:53 PM TIMING BELT REMOVAL/INSTALLATION [ZM] 5. 6. 7. 8. 9. Disconnect the negative battery cable. Remove the CMP sensor.
More information1983 Mazda RX-7 GSL TUNE-UP' 'Mazda Rotary
TESTING ENGINE COMPRESSION The manufacturer recommends using a special compression tester (49 0820 280K). Compression testers for piston engines will read only the highest pressure of the 3 combustion
More informationA: Removing/Installing Camshaft
1 of 6 4/9/2008 9:39 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1995 Mercedes Benz E 320 Cabriolet (124 Chassis) L6-3199cc
More information1 of 8 1/17/2017 8:18 AM
Timing Belt Service and Repair, Removal and Replacement: Replacing... http://repair.alldata.com/alldata/article/display.action?componentid=64&... 1 of 8 1/17/2017 8:18 AM Replacing the timing belt Special
More informationGenerator, removing and
Page 1 of 14 27-26 Generator, removing and installing CAUTION! Disconnect the battery Ground (GND) strap before working on the electrical system. Notes: Before disconnecting the battery, determine the
More informationDISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY DISCONNECT CAM POSITION SENSOR CONNECTOR
1 of 12 4/26/2008 1:50 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1987 Toyota Supra L6-3.0L DOHC Turbo (7M-GTE) Conversion
More informationService and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3.
1 of 12 5/4/2008 10:31 PM Home Account Contact ALLDATA Log Out Help METRO TOYOTA Select Vehicle New TSBs Technician's Reference 1992 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Vehicle Level Engine, Cooling
More informationTORQUE SPECIFICATIONS
2000 Suzuki Truck Grand Vitara LTD JLS 2WD V6-2.5L Vehicle > Engine, Cooling and Exhaust > Engine > Specifications > Mechanical TORQUE SPECIFICATIONS Engine Torque Specifications TORQUE COMPONENT TIGHTENING
More information?P.. Bulletins - SI/MI - ( utg. 2) Replacement of check valve and banjo screw to remedy blue smoke
MODIFICATION INSTRUCTION Bulletin Nbr: 291-2217 utg. 2 Date:...Maj 2000 Market: US, CA, JP Replacement of check valve and banjo screw to remedy blue smoke Emissions-related campaign 10719 Cars in stock
More informationValve Cover - RH Material
1 of 5 5/15/2015 8:06 AM Valve Cover - RH Material 2 of 5 5/15/2015 8:06 AM 3 of 5 5/15/2015 8:06 AM Removal CAUTION: During engine repair procedures, cleanliness is extremely important. Any foreign material,
More informationIntake Manifold Replacement
ALLDATA Online - 2001 Cadillac DeVille V8-4.6L VIN 9 - Intake Manifold Replacement Page 1 of 15 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's
More informationASSEMBLY/INSTALLATION INSTRUCTIONS
ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath
More informationDifferential Assembly Remove and Install ( ) Remove. Rear Axle. Special Tools. Workshop Equipment Transmission jack Angle gauge
Differential Assembly Remove and Install (5 54 0) Special Tools 540-540 Angle gauge Workshop Equipment Transmission jack Materials High-temperature grease WSD-MC37-A Remove. Remove the rear part of the
More informationRemoval & Installation of Hydraulic Cylinder For Soft Top Bow
1 of 4 4/29/2008 9:59 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1997 Mercedes Benz SL 500 (129.067) V8-5.0L (119.982)
More information6.7L Cummins EGR Delete
6.7L Cummins EGR Delete H I A B E C D F J K G L PACKING LIST: Part# A B C D E F G H I J K L QTY. 4 Description Coolant Hose Coolant Hose Connector M0 Flange Nut 5/6 Bolts, Nuts, and Flat Washers /4-0 Bolt,
More information512 HO M285 Engine (FrechW) Maybach Engine M285
512 HO M285 Engine (FrechW) 08-06-03 Maybach Engine M285 These technical training materials are current as of the date noted on the materials, and may be revised or updated without notice. Always check
More information3/13/ :32 AM. NOTICE: Do not disconnect the hose.
1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install
More informationINSTRUCTION. Internal pump elements APP6.5 - special 180B R R9134
INSTRUCTION Internal pump elements APP6.5 - special 180B3101 180R9134 This document covers the instructions for changing internal pump elements on the axial piston pumps APP6.5. Note: It is essential that
More informationPistons and Connecting Rods, Remove and Install
Page 1 of 46 Pistons and Connecting Rods, Remove and Install Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release
More informationCylinder head/gasket, replacing
1(16) Cylinder head/gasket, replacing Special tools: 951 2666, 951 2767, 999 5450, 999 5452, 999 5454, 999 5670, 999 5718, 999 5719, 999 5750, 999 5972 Removing the cylinder head gasket Note! As the illustrations
More informationVolkswagen > New Beetle, New Beetle Convertible > Liter 4-Cyl. 2V Generic Scan Tool, Engine Code(s): AEG 24 - Components, Checking
Page 1 of 9 Volkswagen > New Beetle, New Beetle Convertible > 1998-2008 2.0 Liter 4-Cyl. 2V Generic Scan Tool, Engine Code(s): AEG 24 - Components, Checking. Throttle Valve Control Module J338, Checking
More information1 of 5 1/10/2017 5:10 PM
1 of 5 1/10/2017 5:10 PM Shock Module Yoke Replacement ^ Tools Required - J 24319-B Steering Linkage and Tie Rod Puller Removal Procedure 1. Raise and support the vehicle. Refer to Vehicle Lifting. 2.
More informationCylinder Head, Remove and Install (Z 22 SE)
Page 1 of 29 Cylinder Head, Remove and Install (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release the
More informationOil trap electrically heated, replacing
1(5) Oil trap electrically heated, replacing Removing Note! As the illustrations in the information are used for different model years and/or models, some variation may occur. However, the essential information
More informationFuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine)
Page 1 of 49 20-6 Fuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine) Note: VAG1921 spring clamp pliers are recommended for installation Always replace
More information1 of 11 8/12/2015 3:23 PM
1 of 11 8/12/2015 3:23 PM ENGINE CONTROL MODULE (ECM) REPLACEMENT REMOVAL PROCEDURE NOTE: Always turn the ignition off when installing or removing the ECM connectors in order to prevent damage to the components.
More informationInstallation Instructions Camaro ZL1 ( Z) ( ZB)
Installation Instructions Camaro ZL1 (501-1099-10-Z) (501-1099-10-ZB) Parts List 1 Insulated Air Box \ Lid 1 Thermal Coated Intake Tube / MAF Housing with (2) M4 x.7 thread 8mm long Stainless Screws; 1
More information1 of 1 7/1/17, 2:02 PM. Air Cleaner Assembly Replacement ALLDATA, LLC. All Rights Reserved. (Version )
Air Cleaner Housing Service and Repair, Removal and Replacement: Ai... http://repair.alldata.com/alldata/article/display.action?componentid=367... 1 of 1 7/1/17, 2:02 PM Air Cleaner Assembly Replacement
More information2016+ Camaro V8 or V6/I4 Exhaust Kit
2016+ Camaro V8 or V6/I4 Exhaust Kit Installation Instructions P/N: 620079 (99-135) P/N: 620078 (99-136) 39555 Schoolcraft Rd, Plymouth MI, 48170 855.SLP.PERF 2016+ Camaro V8 or V6/I4 Exhaust Kit Installation
More information2006 Audi S4 Quattro Sedan (8EC) V8-4.2L (BHF)
1 of 6 2/21/2013 6:57 PM 2006 Audi S4 Quattro Sedan (8EC) V8-4.2L (BHF) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Cylinder Head Cylinder Head Removing All
More information3. FRAME/BODY PANELS/EXHAUST SYSTEM
3. FRAME/BODY PANELS/EXHAUST SYSTEM SERVICE INFORMATION 3-2 TROUBLESHOOTING 3-2 SEAT 3-3 MUD GUARD/FOOTPEG 3-3 TOP COVER ('04 - '05) 3-5 TOP COVER (After '05) 3-5 FRONT FENDER ('04 - '05) 3-6 FRONT FENDER
More informationTiming Chain, Balancer Shaft, Replace (Z 22 SE)
Page 1 of 34 Timing Chain, Balancer Shaft, Replace (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release
More informationMUELLER GAS. Shur StopTM Unit 812 PE Line Stopping. System 8" 12" SDR Reliable Connections. General Information 2
operating Instructions manual MUELLER GAS TAble of contents PAGE TM Unit 812 PE Line Stopping General Information 2 Equipment, Parts and Dimensions 3-5 Operating Instructions 6-12 Troubleshooting and Storage
More informationLenntech. Tel Fax
Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 INSTRUCTION Internal pump elements APP5.1-10.2 180R9093 This document covers the instructions for changing internal
More informationALLDATA Online Dodge Truck Caravan V L - Front. Front
Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1994 Dodge Truck Caravan V6-201 3.3L Conversion Calculator Vehicle
More information2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300
Crankcase Vent Housing Removal Fig. 324: Removing & Installing Engine Vent Housing 1. Remove the hoses from the chamber. 2. Remove the chamber bolts. 3. Remove the chamber. 4. Remove the gasket material.
More information2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
More informationFREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
More informationChanging the Engine Oil and Filter
Changing the Engine Oil and Filter 1. While engine is still somewhat warm take out drain plug and drain oil 2. Put plug back in 3. Remove old oil filter (be careful as oil will drain from filter) 4. Apply
More informationDrive/Propeller Shaft: Service and Repair Removing and Installing Rear Cardan Shaft Removing and installing rear cardan shaft Tools
2005 Porsche Cayenne V8-4.5L Page 1 Drive/Propeller Shaft: Service and Repair Removing and Installing Rear Cardan Shaft Removing and installing rear cardan shaft Tools Preliminary work for rear cardan
More information2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
More informationDriveshaft, servicing
Page 1 of 23 39-73 Driveshaft, servicing Important notes A distinction is made between two driveshafts: Driveshaft made of steel Driveshaft made of carbon fiber Only carbon fiber driveshafts were installed
More informationRepair Manual 11/99 PS-34. Page 1
Repair Manual /99 PS-4 Page Table of contents Index Technical Data page Special tools 4 Repair instructions, general 0 Chain brake 6 0 Centrifugal clutch 8 0 Oil pump 9-04 Ignition system - 0 Starting
More information1 of 15 1/26/2017 8:57 AM
1 of 15 1/26/2017 8:57 AM Timing Belt and Balancer Belt Removal Special Tools Required ^ Holder Handle 07JAB-001020A ^ Holder Attachment, 50 mm, Offset 07MAB-PY3010A ^ Socket, 19 mm 07JAA-001020A or a
More information2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: (99-137)
2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: 422046 (99-137) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions
More information2015+ Ford F-150 Off-Road Exhaust Kit
2015+ Ford F-150 Off-Road Exhaust Kit Installation Instructions P/N: 421985 (1115-5E292ORR) Application: 2015+ Ford F-150 OFF-ROAD USE ONLY Important Note: Before installing the ROUSH Performance Product,
More information1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
More informationN63 Valve Stem Seal Tool Kit Part #: AGA-N63-VSK-K
N63 Valve Stem Seal Tool Kit Part #: AGA-N63-VSK-K Problem: Your BMW is smoking due to bad valve stem seals. Old valve stem seals harden over time and no longer provide a proper seal between the seal and
More informationDISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
More informationEngine Remove and Install ( ) Remove. Section Title. Special Tools. Workshop Equipment Trolley jack A Engine lifting tackle
Engine Remove and Install ( 4 0) Special Tools 068A 068A0-068A Engine lifting tackle -068A-0 Lifting eyebolts Workshop Equipment Trolley jack Materials High-temperature grease ESDM-C0-A Proprietary Tools
More information2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
More informationF L Ecoboost V F L Ecoboost V6 Performance Pac Level 2 Installation Instructions P/N: (1115TT-PWRPK2)
2015-2016 F-150 3.5L Ecoboost V6 2015-2017 F-150 2.7L Ecoboost V6 Performance Pac Level 2 Installation Instructions P/N: 422007 (1115TT-PWRPK2) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015-2016
More informationTurbocharger system. Note: Observe rules of cleanliness Page Charge air pressure control connection diagram Page 21-2.
Page 1 of 50 21-1 Turbocharger system Note: Observe rules of cleanliness Page 21-22. Charge air pressure control connection diagram Page 21-2. All hose connections are secured with hose clamps: parts catalog.
More information2002 Dodge or Ram Truck RAM 2500 Truck 4WD L6 5.9L DSL Turbo VIN 6
2002 Dodge or Ram Truck RAM 2500 Truck 4WD L6 5.9L DSL Turbo VIN 6 Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Diesel MFI Pump» Service and Repair REMOVAL CAUTION: Refer to Cleaning
More informationALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair
Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special
More informationCoolant Pump, Remove and Install (Z 22 SE)
Page 1 of 10 Coolant Pump, Remove and Install (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the rear engine cover (1). 4. Detach the rear engine cover. 6 bolts (2) and (3) 5.
More informationHYBRID DEVELOPMENT INTERNATIONAL RACING INTERCOOLER KIT INSTALLATION MENU SUBARU LEGACY B4 BL5 SUBARU LIBERTY GT BL5
HYBRID DEVELOPMENT INTERNATIONAL RACING INTERCOOLER KIT INSTALLATION MENU SUBARU LEGACY B4 BL5 SUBARU LIBERTY GT BL5 Please read before continue Please read through all the instruction and practice all
More informationREMOVAL. Engine removal is not required for this procedure. Remove the engine cover(a).
1 of 25 12/11/2012 4:43 PM REMOVAL Engine removal is not required for this procedure. 1. Remove the engine cover(a). 2. 3. Remove the RH front wheel. Remove the 2 bolts(b) and RH side cover(a). 2 of 25
More information2015+ Mustang GT V8 X-Pipe/H-Pipe Exhaust Kit Installation Instructions
2015+ Mustang GT V8 X-Pipe/H-Pipe Exhaust Kit Installation Instructions P/N: 422046 and 422119 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang GT V8 X-Pipe/H-Pipe Exhaust Kit Installation
More information1999 F-150/250 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 4.6L and 5.4L IN-VEHICLE REPAIR Procedure revision date: 02/03/1999 Intake Manifold Lightning Removal WARNING: Do not smoke or carry lighted tobacco or open flame of
More information1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
More informationAll other use than mentioned above, is the entire responsibility of the owner and/or driver.
The G-Force V-MAX supercharger kit was built to raise the engines horse power of your motorcycle. Make sure you respect the law of your Country for vehicle modification. This system installed on a motorcycle
More informationFuel Filter Housing, Remove and Install (Z 19 DT, Z 19 DTH)
602854Fuel Filter Housing, Remove and Install (Z 19 DT, Z 19 DTH) file://c:\program Files\cosids\DATA\TMP\00602854.rtf.html Page 1 of 2 Fuel Filter Housing, Remove and Install (Z 19 DT, Z 19 DTH) Warning:
More informationValve Body Service and Repair, Removal and Replacement: 0B5A Transmission, Mecha...
Page 1 of 7 Mechatronic Circuit Board, Removing and Installing Removing - Remove the DSG Transmission Mechatronic (J743). Refer to => [ Mechatronic, Removing and Installing ] See: Valve Body, ASMT > Removal
More informationFig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS
connecting rods are marked for reassembly. 3. Thoroughly clean and inspect all components. Coat pin with engine oil and heat piston to 158-176 F (70-80 C). Pin should push fit with thumb pressure through
More information2006 Chevrolet Impala SS ENGINE Engine Electrical - Impala
BATTERY REPLACEMENT (RPOS LZE/LZ4/LZ9) Removal Procedure IMPORTANT: Do not tip the battery more than 40 degrees during removal. Fig. 52: View Of Negative Battery Cable Terminal & Battery 1. Disconnect
More information1992 Toyota Cressida
Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May
More informationARTICLE BEGINNING INTRODUCTION IGNITION SYSTEM CAMSHAFT POSITION (CMP) SENSOR DISTRIBUTOR
Article Text Thursday, August 19, 1999 11:40PM ARTICLE BEGINNING 1996 ENGINE PERFORMANCE Volkswagen Removal, Overhaul & Installation - Gasoline Cabrio, Golf III, GTI, Jetta III, Passat CAUTION: When battery
More informationON-VEHICLE INSPECTION
452 DLC3 CAN VIM Intelligent Tester G035612E02 ON-VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Listen to the throttle control motor operating sounds. (1) Turn the ignition switch to ON. (2) When pressing
More informationF L and 2.7L Ecoboost V6
2015-2016 F-150 3.5L and 2.7L Ecoboost V6 Installation Instructions P/N: 421981 (1115TT-9600) Application: 2015-2016 Ford F-150 2.7L Ecoboost V6, 2015-2016 Ford F-150 3.5L Ecoboost V6 Important Note: Before
More information2015+ Mustang LoudMouth I and LoudMouth II Exhaust Kits
2015+ Mustang LoudMouth I and Installation Instructions P/N: 620054, 620055, 620061, 620062 (S1315-5231LM1, S1315-5231LM2, S1315S1-5231LM1, S1315S1-5231LM2) *LoudMouth II shown. BY 39555 Schoolcraft Rd,
More informationTiming Belt: Service and Repair TIMING BELT
2008 Hyundai Accent L4-1.6L Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT EMOVAL Engine removal is not required for this procedure. 1. Remove the engine cover. 2. Remove
More informationDISASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More informationENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More informationEngine and A4LDE Automatic Transmission Remove and Install ( ) Remove
Engine and A4LDE Automatic Transmission Remove and Install ( 3 0) Special Tools 068A -068A Engine lifting bracket -540 Bolt tightening angle gauge Workshop Equipment Transmission jack Workshop crane Assembly
More informationInstallation Manual v1.0: P/N 202-A Aurora 3000/5000 Compound Turbo Kit Dodge Cummins 5.9
Installation Manual v1.0: P/N 202-A35-2272 Aurora 3000/5000 Compound Turbo Kit 2003-2007 Dodge Cummins 5.9 Please read all instructions before installation. Figure 1. Figure 2. Figure 3. Figure 4. 1. Install
More informationOverview of rear lid trim panels
Overview of rear lid trim panels Overview of rear lid trim panels 1 - Rear lid trim (bottom) Exploded view and installing 2 - Rear lid trim (top) Exploded view and installing vw-wi://rl/a.en-gb.a00.5a50.39.wi::46107222.xml?xsl=3
More informationSubaru WRX MRT Turbo Back Exhaust System
2015-16 Subaru WRX MRT Turbo Back Exhaust System Part No. 98P113 STOP Verify that all of the following components are included in kit before beginning installation: Part #1 J-Pipe / Downpipe Part #2 Mid-Pipe
More informationTECHNICAL SERVICE BULLETIN
TSB No. 2-2418 ed. 4 Date April 2006-3 (400) Distr. all TECHNICAL SERVICE BULLETIN Oil leakage from engine Cars affected Saab -3 (400) M - M03 with engine variants B205 and B235 Background The flow through
More informationIN-VEHICLE REPAIR. Upper Intake Manifold
303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric
More informationPIERBURG. Carburetor: 2E3
PIERBURG Carburetor: 2E3 1 fast idle adjusting screw 2 throttle lever 3 fuel mixture adjusting screw 4 main body 5 idle cut off valve 6 stop screw 7 accelerator pump cover 8 diaphragm 9 spring 10 valve
More informationSteering Gear: Service and Repair POWER STEERING GEAR BOX
2003 Kia Truck Sorento V6-3.5L Copyright 2013, ALLDATA 10.52 Page 1 Steering Gear: Service and Repair POWER STEERING GEAR BOX COMPONENTS REMOVAL 1. Drain the power steering fluid. 2. Disconnect the pressure
More information2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,
More informationCAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
Installation Engines with ratcheting timing chain tensioners 1. CAUTION: Timing chain procedure must be followed exactly or damage to valves and pistons will result. CAUTION: Do not compress the ratchet
More informationM-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly
More information