2014+ Ram 3.0 EcoDiesel EGR Delete
|
|
- Colin Reeves
- 6 years ago
- Views:
Transcription
1 2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD Step 1 Removing air filter and intake tube. Disconnect MAF Sensor by pulling the red tab back out of the connector. Page 1 of 27
2 Page 2 of 27 Disconnect the intake tube from the air cleaner box by untightening the band. Removing the air filter by popping the (4) clips that hold the air cleaner box lid on and remove the lid and filter. Trace the intake tube until you locate the intake tube clamp. Loosen the clamp and remove the intake tube from the turbo.
3 Remove inner wheel well plastic Note: Not required but can very helpful later in the process. Removing lower air cleaner box Remove all remaining clips so the box is free of wires. Remove screws from inside the wheel well plastic. (Note: This step is only necessary if you don t remove the wheel well plastic) Lift lower air cleaner box straight up until it is free from the dowels. You can now remove the box from the truck. Page 3 of 27
4 Removing Vacuum Line Locate vacuum line attached to EGR actuator and disconnect. Page 4 of 27
5 Trace line from actuator to the solenoid and remove any clips from the line. (Will be on passenger side of throttle plate assembly) Remove the line from the solenoid and slowly pull line towards the front of the truck while guiding the rear of the line to fully remove. Page 5 of 27
6 Removing EGR Actuator Remove e-clip and washer from the front of the actuator (Be sure not to drop the washer) Remove (2) T-25 bolts from the bracket Page 6 of 27
7 Pull actuator arm off the unit (towards the front of the truck). Removing Electrical Disconnect blue connector by releasing and pulling tab towards the front of the truck Disconnect red connector by lifting up on the yellow tab. Page 7 of 27
8 Page 8 of 27 Disconnect large black connector by pulling the red tabs towards the back of the truck.
9 Lift gray handle until the plug separates and then disconnect the plug. Push the fixed part of the plug towards the ground to reveal the two clips holding it to the black bracket using the appropriate tools free the plug from the bracket. Once removed disconnect any remaining clips from the bracket. Step 2 Coolant Lines Removing the Coolant Lines Drain about 1 gallon of coolant by removing the cap off of the coolant reservoir. Then locate the radiator drain plug under the front drivers side of the truck. Using a 16mm wrench break the drain loose (be careful not to break the drain itself because the drain is plastic) then you should be able to turn the drain by hand. Page 9 of 27
10 Drain about 1 gallon of coolant out of the truck or until the drain begins to drip slowly. When finished turn the drain off making sure the nut locks into place. Page 10 of 27
11 Removing rear coolant hard lines Locate the rear coolant junction on the body of the EGR. Page 11 of 27
12 Using pliers to free the clamp pull the clamp towards the rear of the truck. Trace the lower coolant line until you find the hard pipe (Note: this will be removed in Step 3 after the EGR has been removed to allow better access.) Page 12 of 27
13 Remove the (2) 10mm bolts (Note: Coolant will drain out of the hose and EGR) Page 13 of 27
14 Next locate the front coolant line (Note: DO NOT DROP OR DAMAGE GASKET. IT WILL BE REUSED). Now remove the (2) 8mm bolts being sure to catch the gasket after removing the second bolt. Page 14 of 27
15 Removing EGR tube Locate the top flange of the EGR tube (Note: This flange is located directly behind the actuator that was removed earlier). Remove the (2) 10mm bolts that connect the tube to the EGR unit (Note: You can carefully bend the heat shield to better access the bolts). Note: You will remove the bottom EGR tube bolts later on. Page 15 of 27
16 Step 3 Remove EGR Valve and EGR Cooler Removing the EGR Cooler Locate and remove a T-40 bolt on the back of the EGR cooler. (Note: This bolt is very difficult to see) Page 16 of 27
17 Page 17 of 27 Remove the Lower Support Bracket (Black Bracket) by locating and removing the (3) 10mm bolts.
18 Remove the Lower EGR Cooler Manifold by locating and removing (3) 13mm bolts (Note: 2 of these bolts will be reused later) At this point you can remove the unit from the truck. Page 18 of 27
19 Step 4 Removing Coolant Line and EGR Tube Lower Coolant Line You will return to the coolant line that was not removed in Step 2. Using pliers you will squeeze the spring clamp and move it so the hose can be removed from the hard coolant line. Remove the coolant hose from the hard line. Page 19 of 27
20 Removing EGR Tube - (Note: This can be done from under the truck or above). Trace the rear EGR tube down to the turbo manifold to locate the (3) 8mm bolts that will be removed. (Note: These bolts will not be reused but the gasket will be) Page 20 of 27
21 Step 5 Installation of Off Road Conversion Kit Install Turbo Manifold Block Off Plate Using (3) 10mm bolts (included) and reusing the factory gasket secure the rear block off plate to the turbo manifold Page 21 of 27
22 Install Block Off Bracket Reusing (2) 13mm bolts attach the Block Off Bracket to the 2 points shown below (Note: These are the same bolt locations that the EGR unit was mounted to) Page 22 of 27
23 Connect Front Coolant Line Reusing (2) 8mm bolts with the included (2) 10mm nuts to attach the front coolant line and gasket to the front of the Block Off Bracket. Page 23 of 27
24 Rear Coolant Line Adapter Locate the lower coolant line that was removed in Step 4 and place a supplied clamp on to the end of the hose that does not have the reducer. Slide hose onto the lower coolant hard pipe and secure with clamp. Page 24 of 27
25 Locate the upper coolant line (the line that runs to the firewall) and install the supplied on the hose. Insert the reducer into the upper coolant hose and secure with clamp. Page 25 of 27
26 Attach coolant line to the Block Off Bracket using the supplied zip tie Page 26 of 27
27 Attaching the electrical Attach the large electrical connector to the Block Off Bracket Attach the small wiring harness to the large wiring harness using the included zip ties Step 6 - Final steps 1. Re-install air box, intake tube and engine cover 2. Re-fill engine coolant 3. Start engine and check for coolant leaks 4. All done! Visit us at rudysdiesel.com for more EcoDiesel parts! Page 27 of 27
H F G I. A (1) Reducer. pg.2
301009 B A D C E H F G I J L M A (1) Reducer B (1) Coolant hose C (1)Block off bracket D (3) Clamps E (1) Cooler side block off plate F (1) Turbo manifold block off plate G (1) Intake manifold side blocker
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More informationFord 6.7 EGR Delete Kit
Fits: 2011 12 Powerstroke 6.7L Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** ***This kit is intended for off road use only.***
More informationForbidden Diesel Performance Ford 6.7L Powerstroke EGR Delete Instructions 6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE. Page 1
6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE Page 1 WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road
More informationINSTALLATION MANUAL
315000 INSTALLATION MANUAL EGR & Cooler Race Kit for 2015+ 6.7L Ford Powerstroke WARNING ONLY install this kit if you are using a tuner that disables the EGR sensors & circuit system. Any product that
More informationPage 6 of 6 OUTLAW DIESEL EGR COOLER DELETE KIT W/INTAKE ELBOW L FORD POWERSTROKE
What s in the box 1 Exhaust Block-Off Plate 1 Exhaust Gasket 2 Coolant Line Plugs 1 Brass Barbed Hose Connector 1 Stand-off Spacer 4 M10-1.25 x 40 Hex Head Bolts (Exhaust Manifold) 2 M10-1.25 x 20 Hex
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More information* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION
XDP 6.0L Complete EGR Delete Kit w/up-pipe Item Number: XD169 PACKING LIST: 2 - Lined 3/4" Hose Clamps, 1-180 Coolant Tube, 1-3/4 Silicone Hose, 1 - Stainless Steel Up-pipe 1 - EGR Valve Block-Off Plate,
More informationXDP Complete EGR Race Track Kit w/up-pipe. Item Number: XD144
XDP Complete EGR Race Track Kit w/up-pipe Item Number: XD144 PACKING LIST: 2 - Lined 3/4" SS Hose Clamp 1-3/4 Silicone Hose 1 - XDP Engraved EGR Valve Block-Off Plate with O-ring 1 - EGR Cooler Block-Off
More information* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION *
XDP Duramax LBZ EGR Race Track Kit Item Number: XD165 PACKING LIST: 1 LBZ EGR Plate for Up Pipe 5 M8x1.25-20mm Bolt 2 M10x1.5 Flange Hex Nut 1 LBZ EGR Plate for Intake 1 M8x1.25-45mm Bolt 1 M8x1.25 Flange
More informationInstallation Instructions
BD DODGE CUMMINS PERFORMANCE E X H A U S T M A N I F O L D Installation Instructions Application List 2007-2015 6.7L / HE351 OE Turbo 1045965 2007-2015 6.7L / T4 S400 Turbo s 1045965-T4 PLEASE READ ALL
More informationDURAMAX LMM EGR DELETE
007.5-010 DURAMAX LMM EGR DELETE Duramax LMM EGR Delete B K I J F D G H A C PACKING LIST: E Part # A B C D E F G H I J K QTY. 1 1 1 1 Description Billet Intake Block Off Plate with O-ring Exhaust Block
More informationIncluded: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware -
Included: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware - Nuts, Bolts, & Washers 2. Hose Clamps 1. Support Bracket
More informationINSTALLATION GUIDE: EGR Delete Kit Ford 6.7L Powerstroke`
INSTALLATION GUIDE: EGR Delete Kit 20 203 Ford 6.7L Powerstroke` ! Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing
More informationIncludes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts
Includes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts WARNING: This product is not legal for sale or use on pollution controlled
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More informationHR ZDX Throttle Body Install (06-11 Civic Si)
HR ZDX Throttle Body Install (06-11 Civic Si) This guide will walk you through the steps to install a ZDX throttle body onto your RBC Intake manifold using the Hybrid Racing ZDX adapter. Written By: Hybrid
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationGHG14 DD15 Asymmetrical Turbocharger May Removal of the GHG14 DD15 Asymmetrical Turbocharger
5 31-13 1 5 31-13 SUBJECT DATE GHG14 DD15 Asymmetrical Turbocharger May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the GHG14 DD15 Asymmetrical
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationASSEMBLY/INSTALLATION INSTRUCTIONS
ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath
More information6.4L EGR Delete With Intake Elbow
6.4L EGR Delete With Intake Elbow J I E C B F D G H A Part# A B C D E F G H I J PACKING LIST: QTY. 2 4 2 4 2 Description Exhaust Block-Off Plate Exhaust Gasket Coolant Line Plugs Brass Barbed Hose Connector
More informationLML 3 Y-Bridge Kit or High Flow Intake Bundle Package
2011-2016 LML 3 Y-Bridge Kit or High Flow Intake Bundle Package Covers installation of PN s: WCF100607, WCF100691, WCF100716, & WCF100353 Note: This Kit is for off road competition use only! Overview-
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More informationIncludes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses
Includes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses CAUTION: Never work on a hot vehicle. The hot exhaust system or hot engine can cause serious injury in the form of burns. If the vehicle has
More informationIAG Competition Series Air / Oil Separator (AOS) For 2017 STI
P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationINSTALLATION INSTRUCTIONS Dual Catch Can Kit Subaru Turbo and STi Document# Support:
INSTALLATION INSTRUCTIONS Dual Catch Can Kit 02-14 Subaru Turbo and 2015+ STi Document# 19-0099 Support: info@radiumauto.com This document covers the installation of a Radium dual catch can kit for the
More information10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
More informationIncludes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps
Includes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps WARNING: This product is not legal for sale or use on pollution controlled vehicles
More informationIncludes: 1. High Flow Turbo Up-Pipe 1. J-Hook Block Off / Coolant Reroute 1. Coolant Hose 1. EGR Valve Block Off Plate 2. Hose Clamps 4.
Includes: 1. High Flow Turbo Up-Pipe 1. J-Hook Block Off / Coolant Reroute 1. Coolant Hose 1. EGR Valve Block Off Plate 2. Hose Clamps 4. Bolts & Nuts WARNING: This product is not legal for sale or use
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More information8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)
P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationApplication List L Cummins
1 Discharging & Recharging of the A/C System is required for this install. INTERCOOLER INSTALLATION FOR 2010+ DODGE 6.7L CUMMINS Application List 2010+ 6.7L Cummins 1042530 PLEASE READ ALL INSTRUCTIONS
More informationFord Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours
Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen
More informationStep 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More informationDuramax LMM EGR Delete With Intake Tube
Duramax LMM EGR Delete With Intake Tube PACKING LIST: QTY. 4 2 2 2 Description Intake Charge Pipe w/ O-Ring M8 Flange Nut M8x25 Flange Hex Bolt M0x20 Hex Head Bolts M8x25 Socket Head Bolts M8x20 Hex Head
More informationADM Performance 6079 Mapleshade Lane Dallas, Texas (214)
1) Disconnect Battery Ground 2) Raise front end of Vehicle FAN INSTALL INSTRUCTIONS 3) Remove lower Radiator hose and drain coolant into a pan. (you will reuse coolant later) 4) Remove Air Intake piping
More informationThese instructions were written for reference only and the use of a factory service manual is recommended.
Introducing the CorkSport High Pressure Fuel Line designed for the MZR DISI. This fuel line is designed to replace the OEM fuel line which are prone to failure at the brazed connection at the rail. The
More informationIndustrial Injections Compound Turbo Installation For 6.7L Scorpion
Industrial Injections Compound Turbo Installation For 6.7L Scorpion Step 1: Whenever you are doing an installation the first thing you should do is unhook the batteries to avoid arcing. You will need an
More information6.7L Cummins EGR Delete
6.7L Cummins EGR Delete H I A B E C D F J K G L PACKING LIST: Part# A B C D E F G H I J K L QTY. 4 Description Coolant Hose Coolant Hose Connector M0 Flange Nut 5/6 Bolts, Nuts, and Flat Washers /4-0 Bolt,
More information-Magnet (not completely necessary but can come in handy)
McLeod High Performance Hydraulic Clutch Line Upgrade (05-14 V8) Included in kit: -New clutch line -2 fittings Required Tools: -Floor jack and jack stands (or a lift) -Flashlight -Angled pick tool -13mm
More informationDodge 6.7L
22 March 2016 2007-2010 6.7L Dodge Cummins (I-00014) 1 A Tuner capable of eliminating DTC codes, must be used with this kit. EXHAUST GAS BLOCKER KIT 2007-2016 Dodge 6.7L Part #: 1090011 Part #: 1090012
More informationThese instructions were written for reference only and the use of a factory service manual is recommended.
Introducing the CorkSport High Pressure Fuel Line designed for the MZR DISI. This fuel line is designed to replace the OEM fuel line which are prone to failure at the brazed connection at the rail. The
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationDURAMAX LML EGR DELETE
2011-2012 DURAMAX LML EGR DELETE Sinister Diesel EGR Delete Kit A B C D E F G H PACKING LIST: QTY. A B C D E F G H QTY. 1 4 1 1 1 3 1 4 Description Blue Coolant Hose M8 x 25 Hex Head Bolts Exhaust Block
More informationFord 6.0L Regulated Return Kit
2003-2007 Ford 6.0L Regulated Return Kit A. Passenger Rear Return B. Line (Longer w/ 1-90 fitting) C. Driver Rear Return Line (Shorter w/ 1-90 fitting) D. Fuel Return Line (2 female fittings) E. Passenger
More informationInstallation Manual v1.1: Piece Pulse Flow Exhaust Manifold, Stock Replacement L Cummins
Installation Manual v1.1: 204-927-2326 2-Piece Pulse Flow Exhaust Manifold, Stock Replacement 2007.5-2016 6.7L Cummins Please read all instructions before installation. We suggest purchasing new gaskets
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More informationPage 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1-19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More informationPowerstroke 6.4L EGR Block Kit
Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** You will need the following tools for this installation: 10mm wrench 13mm wrench
More information05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Valve Cover» Service and Repair» Procedures» LH Valve Cover LH Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located
More informationBD TrackMaster S D o d g e H P C R Installation Instructions
7 July 2016 PN#1045701, 1045702, 1045704 Dodge 6.7L TMS400 (I-00361) 1 BD TrackMaster S400 2008-2012 D o d g e H P C R Installation Instructions 1045701 2008-2009 Dodge 6.7L TMS400 1045702 2010-2012 Dodge
More information4 December 2017 PN# , , Dodge 6.7L Rumble B SXE (I-00400) 1. BD Rumble B SXE. D o d g e 6. 7 L H P C R Installation Instructions
4 December 2017 PN#1045705, 1045706, 1045708 Dodge 6.7L Rumble B SXE (I-00400) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Rumble B SXE D o d g e 6. 7 L H P C R Installation Instructions
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More information2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section
Exhaust Gas Recirculation (EGR) Valve 2.3L 1. Drain the cooling system. For additional information, refer to Section 303-03. 2. Disconnect the battery ground cable. For additional information, refer to
More information2001 Lincoln LS Workshop Manual
Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More informationPart number SP Honda Fit cyl. Converts into a short ram
Part number SP1512 2009 Honda Fit 1.5 4 cyl. Converts into a short ram 1- Three piece cold air intake 1-2.75 Injen/AMSOIL (#1010) Ea nano-fiber dry filter 1 2.50 straight hose (#3048) 1- Two bend silicone
More informationDURAMAX LBZ EGR DELETE
006-007.5 DURAMAX LBZ EGR DELETE ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More information2016+ NISSAN TITAN XD
PARTS LIST AND PARTS INCLUDED 1PC MISHIMOTO INTERCOOLER 2PC SILICONE BOOTS WITH DURACORE TECHNOLOGY 4PC CONSTANT-TENSION T-BOLT CLAMPS 2PC ALUMINUM SPACERS MOUNTING HARDWARE CAUTION Never work on the cooling
More informationExhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove
1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release
More informationParts List See cover Page
Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationGM 6.6L DURAMAX LLY EGR DELETE
2004.5-2005 GM 6.6L DURAMAX LLY EGR DELETE ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationDODGE SRT-4 PART NUMBER P (with Turbo Toys) P (without Turbo Toys) P (Stage 2 to Stage 3R Upgrade Kit)
INFORMATION SHEET Stage 3R Turbo Upgrade Kit Components (1) Stage 3R PCM (4) 682 cc/min Fuel Injectors* (1) 3.0 bar MAP Sensor* (1) 3.0 bar TIP Sensor* (1) Block-off Connector for PCM (1) Mopar TD05HR
More informationRotated Tuner Kit for Garrett GT Turbos
Rotated Tuner Kit for Garrett GT Turbos 031411 Thank you for purchasing the PERRIN performance rotated turbo kit. Installation of this turbo should only be performed by persons experienced in the installation
More informationREMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationCOMPONENTS ILLUSTRATION
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION REMOVAL 1. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (a) Remove the windshield wiper motor and link assembly. 2. REMOVE COWL BODY MOUNTING REINFORCEMENT
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
26 September 2012 1045140 6.7L Super B Special Turbo Installation 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140 PLEASE
More informationChevy Sonic 1.4L Intake Manifold
Chevy Sonic 1.4L Intake Manifold Install Time: 3 hours In the Box: (1) Racer X Intake manifold (6) M8x1.25 bolts (4) M6x1 bolts (2) 1/8 NPT plugs (1) 3/8 NPT plug (1) 1/4 NPT 90 degree barb (4) Small O-rings
More informationA Simple Guide to Installing the C2Motorsports 2.5L SRI
A Simple Guide to Installing the C2Motorsports 2.5L SRI Special Thanks to Josh and the Crew at Nothing-Leaves-Stock **Disclaimer: This is an aid for installing the SRI on a 2.5L motor. C2Motorsports is
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationFULL LENGTH HEADERS/ CATTED HEAD PIPES
INSTALLATION INSTRUCTIONS INS232 2016-2018 CAMARO 6.2L V8 FULL LENGTH HEADERS/ CATTED HEAD PIPES Part #4044 and 40440 Special Tools required: 10mm, 12mm, 13mm, 15mm Socket and Wrenches, Pliers, Saw, Welder
More informationENGINE AND EMISSION CONTROL
17-1 ENGINE AND EMISSION CONTROL CONTENTS EMISSION CONTROL SYSTEM... 2 GENERAL... 2 Outline of Changes... 2 GENERAL INFORMATION... 2 SERVICE SPECIFICATION... 2 VACUUM HOSE... 3 Vacuum Hose Piping Diagram...
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More information03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions
Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More informationEXPANSION TANK MUSTANG GT FORD FIESTA ST PARTS LIST AND INSTALLATION GUIDE PARTS LIST AND INSTALLATION GUIDE
PARTS LIST MMHOSE-MUS8-15L: 4 PC SILICONE HOSES 8 PC CLAMPS 1 PC STAINLESS STEEL ADAPTER MMHOSE-MUS8-15U: 1 PC SILICONE HOSE 1 PC QUICK-DISCONNECT FITTING 1 PC CLAMP MMHOSE-MUS8-15ANC: INSTALLATION INSTRUCTIONS
More informationL DURAMAX LBZ EGR DELETE GDP TUNING
2006-2007.5 6.6L DURAMAX LBZ EGR DELETE GDP TUNING ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the be used on vehicles that are operated
More informationThis information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA EGR Valve, Replacement DService Bulletin Trucks Date Group No. Page 11.2006 254 24 1(17) EGR Valve Replacement D16F W2005772 This information covers the proper
More informationSection 7.3 Water Manifold has been updated.
NUMBER: 08 DD15-11 S.M. REF.: 7.3 ENGINE: DD15 DATE: September 2008 SUBJECT: WATER MANIFOLD PUBLICATION: DDC-SVC-MAN-0002 Section 7.3 Water Manifold has been updated. 7.3 WATER MANIFOLD Coolant flows from
More informationSpecial tools required:
11 12 100 Removing and installing/sealing cylinder head (S54) Special tools required: 11 4 400 12 1 120 Remove both exhaust manifolds. Remove intake filter housing with air-mass flow sensor. Remove cylinder
More informationINSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,
More informationPage 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
More information99-04 GT. Hellion Power Systems Mustang GT Kit Instructions
Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationEngine and A4LDE Automatic Transmission Remove and Install ( ) Remove
Engine and A4LDE Automatic Transmission Remove and Install ( 3 0) Special Tools 068A -068A Engine lifting bracket -540 Bolt tightening angle gauge Workshop Equipment Transmission jack Workshop crane Assembly
More information1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
More information