DS4+ INSTALLATION GUIDE TL10. Designed by Installers for Installers

Transcription

1 INSTALLATION GUIDE DS+ TL0 Designed by Installers for Installers 0 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and components. 0-0-

2 Contents Warning! Safety first... Introduction... Pre-installation and application warnings... Vehicle application guide... Wiring connections... Main harness (H), -pin black connector... Relay harness (H), 0-pin white connector... Data harness (H), -pin white connector... Analog input/output harness (H), -pin white connector... RF Port harness (H), -pin white connector... DD harness (H), -pin white () and black () connectors... Temperature sensor harness (H), -pin black connector (optional, T)... Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)... Type with T-Harness (THTON)... Type... 0 Type with T-Harness (THTON)... Type... Type with T-Harness (THTON)... Type... Type with T-Harness (THTON))... Type... Type with T-Harness (THTON)... Type... Type with T-Harness (THTON)... Type... Type with T-Harness (THTON)... Type... Type with T-Harness (THTON)... 0 Type... Type with T-Harness (THTON)... Type... Type 0 with T-Harness (THTON)... Type 0... Type with T-Harness (THTON)... Type... 0 Type with T-Harness (THTON)... Type... Type with T-Harness (THTON)... Type... Type with T-Harness (THTON)... Type... Type with T-Harness (THTON)... Type... Type with T-Harness (THTON)... Type...

3 Configuring the system... Important!... Vehicles equipped with a manual transmission... RF Systems... 0D Combo Sensor... When used in conjunction with SmartStart... DD port configuration... Module programming... LED diagnostics and troubleshooting... 0 Soft reset... Hard reset... Learning the Tach (not needed with Virtual Tach)... Initializing Virtual Tach (not needed with hardwired or data tach applications)... Limited lifetime consumer warranty... Quick Reference Guide...

4 Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, () Never remotely start the vehicle with the vehicle in gear, and () Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. DS+ TL Directed. All rights reserved.

5 Introduction The TL0 firmware for DS+ is compatible with specific Scion and Toyota vehicles. It is a complete solution for remote start, security (when security features are enabled), bypass, and features built in Bluetooth.0 allowing you to configure and control your system. This guide provides information on the installation of the module using TL0. Please refer to the DirectLink application or for more information about which configuration is best for your application. Warning! This module is designed to be configured using the DirectLink application for mobile devices, however it can also be configured using the web tool located at To download the DirectLink mobile application, please visit the Google Play or Apple store. Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness compatible THTON, THTON, THTON Keys required for programming Keys required for operation 0 This guide is compatible with TL0 v.+. It is important to make sure you DO NOT connect the keysense wire in the installation for each of these vehicles or you will encounter issues when attempting to start the vehicle. The optional Plug & Play THTON, THTON and THTON T-Harnesses are sold separately. Refer to the "Vehicle wiring reference chart" for vehicle and t-harness compatibility. The OBDII Diagnostic features will remain the same even when the T-Harness is installed. Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector. It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each wiring diagram. Refer to the "Vehicle wiring reference chart" following each installation type. General notes: This section highlights important information for this specific firmware. [] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin. [] The siren is ONLY required when enabling the security features during module flashing. [] The Green wire is ONLY required for starter disable and antigrind applications. [] Autolight Interrupt connection required only if the vehicle is equipped with automatic headlights. [] SIL Interrupt connection required ONLY if the vehicle is equipped with TPMS (Tire Pressure Monitoring System). [] Trunk release connection required when not available through Data. Additional parts required (maximum required): Diode A 0 x A Diodes a 0 0 x Relay esistor 00 0 x Resistor Fuse.A 0 x Fuse DS+ TL Directed. All rights reserved.

6 Vehicle application guide The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles PK-Immobilizer Bypass-Data No Key Req'd AV-Auto Headlamp Shutoff AV-Parking Lights Control DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock Scion im (H Key) Toyota Camry (H Key) CH-R (H Key) Corolla (H Key) Corolla IM (H Key) Highlander (H Key) Prius c (H Key) RAV (H Key) Sequoia (H Key) Sienna (H Key) Tacoma (H Key) 0 Yaris Hatchback (H Key) W/ OEM Alarm Yaris Hatchback (H Key) W/O OEM Alarm Legend: AV: Horn & Lights Controls DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DL-Driver Priority Unlock DL-Sliding Door Control Driver DL-Sliding Door Control Passenger DL-Trunk / Hatch Release DS+ Only FOB-Control of aftermarket alarm with OEM remote RS-x LOCK START (Start control using OEM Remote) RS-Accessory Activation RS-Ignition Activation RS-SmartStart RS-Start (Crank) Activation RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-Door Locks Status ST-E-Brake Status ST-Ignition Status Key Types Some Toyota 00+ models have different encryption types. Please look look at at your your key key blade blade and and identify identify the the markings. markings. A H means A H means the vehicle the vehicle is compatible is compatible with TL0 with TL0 firmware. firmware. G or a dot. indicates the vehicle is not compatible with this firmware. H-stam ped keys G-stam ped keys Standard Key For vehicles with G-stamped key, see the TL firmware. TL works only with standard key. For vehicles with dot-stamped key, see the TL firmware. TL works only with standard key. H DS+ TL Directed. All rights reserved.

7 Wiring connections The wiring connections listed below are specific to this firmware. Main harness (H), -pin black connector Conn./Pin Color Description H/ Blue/White Relay N.C. SIL Interrupt (vehicle side) H/ Blue/Red Relay N.O. No Connection H/ Blue Relay COM SIL Interrupt (connector side) H/ White/Brown Relay N.C. No Connection H/ White Relay COM (+) Starter Output H/ Red (+) Volt (Battery) H/ Lt. Green/Red Relay N.O. No Connection H/ Lt. Green Relay COM Autolight Interrupt (vehicle side) H/ Lt. Green/White Relay N.C. Autolight Interrupt (connector side) H/0 Black (-) Ground H/ White Relay COM (+) Starter Output H/ Red (+) Volt (battery) Relay harness (H), 0-pin white connector Conn./Pin Color Description H/ N/A No Connection H/ Red/Black (+) Volt Input (Accessory/Starter relay) H/ Pink/Black Relay N.C. Flex Relay Isolation H/ Pink/White Relay COM Flex Relay Output H/ Red (+) Volt Input (Ignition relay) H/ Green Relay COM (+) Starter Disable (key side) H/ Violet Relay N.C. (+) Starter Output (vehicle side) H/ Orange Relay COM (+) Accessory Output H/ Red/White (+) Volt Input (flex relay) H/0 Pink Relay COM (+) Ignition Output Data harness (H), -pin white connector Conn./Pin Color Description H/ Tan HS CAN Low H/ Tan/Black HS CAN High H/ Orange/Brown HS CAN Low H/ Orange/Green HS CAN High H/ Lt. Green No Connection H/ Violet/Brown No Connectiont H/ Orange/Black RDA H/ Yellow/Black SIL Data. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. DS+ TL Directed. All rights reserved.

8 Analog input/output harness (H), -pin white connector Conn./Pin Color Description H/ Lt. Green/Black (-) Parking Lights Output H/ Blue/White (-) Ground When Running (status) Output H/ Dk. Green/Black (-) Lock Output H/ Red/White (-) Trunk Release Output H/ Brown/Black (-) Horn Output H/ Brown/White (-) AUX Output H/ White (+) AUX Output H/ Violet/Black (+) AUX Output H/ Dk. Blue/Black (-) Unlock Output H/0 Lt. Blue/Black (-) Factory Alarm Disarm (FAD) Output H/ Brown/Red (+) Siren Output H/ Pink (+) Ignition Sense Input H/ Violet (+) Door Input H/ Brown (+) Brake Input H/ White/Blue (-) Activation Input H/ Red/Blue (-) Valet Switch H/ Black/White (-) E-Brake Input (manual transmission) H/ Orange/Black (-) Instant Alarm Input H/ Blue (-) Trunk Sense Input H/0 Green (-) Door Sense Input H/ Gray (-) Hood Pin Input H/ Violet/White (AC) Tach Input RF Port harness (H), -pin white connector Conn./Pin Color Description H/ N/A RF Loop H/ N/A RF Loop DD harness (H), -pin white () and black () connectors Conn./Pin Color Description H/ Blue (Data) TX H/ Black (-) Ground H/ Green (Data) RX H/ Red (+) Volt Temperature sensor harness (H), -pin black connector (optional, T) Conn./Pin Color Description H/ Black Temperature Sensor H/ Black Temperature Sensor. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary.. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page for a list of compatible features. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. DS+ TL Directed. All rights reserved.

9 Installation (wiring diagrams, fuse selection & vehicle wiring reference charts) Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Tire Pressure Warning ECU (white conn. on dash fuse box) Body ECU OR BODY ECU FUSES 0 RDA: Green, pin 0 Body ECU (middle or underside conn. of ECU) 0 RDA: Orange/Black SIL Interrupt (conn. side): Blue Siren Hood Pin -pin White (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS SIL: Blue, pin 0 0 Autolight: Violet, pin 0 Headlight Switch SIL Interrupt (veh. side): Blue/White Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White 0-pin White 0 Slide to open DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

10 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU FUSES OR BODY ECU Tire Pressure Warning ECU (white conn. on dash fuse box) Body ECU (middle or underside conn.of ECU) HS CAN High: Red, pin HS CAN Low: White, pin SIL Data: Lt. Green, pin Diagnostic OBDII HS CAN Low : Tan: (+) V: White, pin Dash Fuse Box (white conn.) SIL: Blue, pin Ignition Refer to the Vehicle Wiring Reference Information for wire and connector details. RDA: Green, pin 0 0 Autolight: Violet, pin 0 Headlight Switch Siren Hood Pin HS CAN High : Tan/Black: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (veh. side): Blue/White: SIL Interrupt (conn. side): Blue: (+) Starter Output: White: & (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS DS+ It is important to check that the fuses are positioned correctly. 0 DS+ TL Directed. All rights reserved.

11 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Scion IM (H Key) 0 THTON Toyota Corolla (H Key) 0-0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Scion im (H Key) 0 HS CAN High Red Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Lt. Green Data OBDII. White A RDA Green Data Body ECU, below drivers fuse box. White 0 B Autolights Violet 0 Headlight switch. White 0 C Accessory Black (+) Ignition switch. White D Ignition Green (+) Ignition switch. White D Ignition Gray (+) Ignition switch. White D Starter White (+) Ignition switch. White D V White (+) Dash fuse box. White E SIL Interrupt Blue Rear of dash fusebox. White 0 F Corolla (H Key) 0-0 HS CAN High Red Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Lt. Green Data OBDII. White A RDA Green Data Below drivers fuse box. White 0 B Autolights Violet 0 Headlight switch. White 0 C Accessory Black (+) Ignition switch. White D Ignition Gray (+) Ignition switch. White D Ignition Green (+) Ignition switch. White D Starter White (+) Ignition switch. White D V White (+) Dash fuse box. White E SIL Interrupt Blue Rear of dash fusebox. White 0 F DS+ TL Directed. All rights reserved.

12 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Tire Pressure Warning ECU (behind glove box) Body ECU Body ECU Conn. (middle left side of steering column) 0 0 Siren -pin White (+) Siren Output: Brown/Red: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) MAIN (A) (+) 0 SIL: Blue, pin 0 RDA: Violet, pin RDA: Orange/Black SIL Interrupt (conn. side): Blue SIL Interrupt (veh. side): Blue/White Hood Pin (-) Hood Input: Gray: -pin Black 0 IGN (0A) (+) DS+ Proper Fuse Positioning (-) RLY/PK LIGHT(A) (+) DS Autolight: Green, pin Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (veh. side): Lt. Green/White 0-pin White 0 DS 0 0 Headlight Switch Slide to open DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

13 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU Body ECU (middle conn. left side of steering column) HS CAN High: Violet, pin SIL: Tan, pin Diagnostic OBDII Tire Pressure Warning ECU (behind glove box) 0 0 RDA: Violet, pin 0 SIL: Blue, pin 0 HS CAN Low: White, pin HS CAN Low: Tan: Siren Hood Pin HS CAN High: Tan/Black: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (veh. side): Blue/White: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ DS MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) Dash Fuse Box (white conn.) Ignition (+) V: Black, pin Autolight: Green, pin 0 0 Headlight Switch SIL Interrupt (conn. side): Blue: (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 Proper Fuse Positioning Slide to open DS DS+ Refer to the Vehicle Wiring Reference Information for wire and connector details. It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

14 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Sequoia (H Key) 0-0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Sequoia (H Key) 0-0 HS CAN High Violet Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Tan Data OBDII. White A SIL Interrupt Blue 0 TPMS warning ECU behind glove box. White F RDA Violet Data Main body ECU left of steering column. White B Autolights Green Headlight switch. White 0 C Accessory Gray (+) Ignition switch. White D Ignition Black (+) Ignition switch. White D Ignition Lt. Green (+) Ignition switch. White D Starter Green (+) Ignition switch. White D V Black (+) Dash fuse box. White E DS+ TL Directed. All rights reserved.

15 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Body ECU Tire Pressure Warning ECU (left of steering column) SIL: White, pin 0 0 Body ECU (middle or underside conn. of ECU) 0 0 RDA: Pink, pin 0 RDA: Orange/Black SIL Interrupt (conn. side): Blue SIL Interrupt (veh. side): Blue/White Autolight Interrupt (veh. side): Lt. Green Siren Hood Pin -pin White (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning DS MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) 0 0 Autolight: Violet, pin Headlight Switch Autolight Interrupt (conn. side): Lt. Green/White 0-pin White 0 DS Slide to open DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

16 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU Body ECU (middle or underside conn. of ECU) SIL: White, HS CAN High: Red, pin pin Diagnostic OBDII HS CAN Low: White, pin HS CAN Low: Tan: RDA: Pink, pin Tire Pressure Warning ECU (left of steering column) 0 SIL: White, pin 0 Siren Hood Pin HS CAN High: Tan/Black: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) SIL Interrupt (veh. side): Blue/White: DS+ DS Ignition SIL Interrupt (conn. side): Blue: (+) V Input: Red: & Proper Fuse Positioning Refer to the Vehicle Wiring Reference Information for wire and connector details. 0 Autolight: Violet, pin 0 Headlight Switch Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 Slide to open DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

17 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Sienna (H Key) 0-0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Sienna (H Key) 0-0 HS CAN High Red Data OBDII. White A HS CAN Low White Data OBDII. White A SIL White Data OBDII. White A SIL Interrupt White 0 ECU left side of the dash fuse box. White F RDA Pink Data Middle Plug main body ECU left of steering column. White 0 B Autolights Violet Headlight switch. White 0 C Accessory Blue (+) Ignition switch. White D Ignition Black (+) Ignition switch. White D Ignition Yellow (+) Ignition switch. White D Starter Red (+) Ignition switch. White D V Red (+) Ignition switch. White D DS+ TL Directed. All rights reserved.

18 Type with T-Harness (THTON)) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Tire Pressure Warning ECU (white conn. on Body ECU) Body ECU SIL: Yellow, pin Autolight: Black, pin 0 RDA: Lt. Green, pin 0 0 Body ECU (middle conn. left side of steering column) RDA: Orange/Black SIL Interrupt (conn. side): Blue SIL Interrupt (veh. side): Blue/White Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White Siren Hood Pin -pin White (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black 0-pin White 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS 0 0 Slide to open DS+ Headlight Switch It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

19 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). HS CAN High: Violet, pin SIL Data: Lt. Blue, pin Diagnostic OBDII Tire Pressure Warning ECU (white conn. on Body ECU) SIL: Yellow, pin 0 0 RDA: Lt. Green, pin Ignition Refer to the Vehicle Wiring Reference Information for wire and connector details. Body ECU Conn. (middle left side of steering column) 0 0 Autolight: Black, pin Headlight Switch HS CAN Low: White, pin Siren Hood Pin HS CAN Low : Tan: HS CAN High : Tan/Black: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (veh. side): Blue/White: SIL Interrupt (conn. side): Blue: (+) Starter Output: White: & (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

20 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Highlander (H Key) 0-0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Highlander (H Key) 0-0 HS CAN High Violet Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Lt.Blue Data OBDII. White A RDA Lt.Green Data Middle Plug main body ECU left of steering column. White 0 B Autolights Black 0 Headlight switch. White 0 C Accessory Gray (+) Ignition switch. White D Ignition Black (+) Ignition switch. White D Ignition Green (+) Ignition switch. White D Starter Blue (+) Ignition switch. White D Starter Gray (+) Ignition switch. White D V Black (+) Ignition switch. White D SIL Interrupt Yellow 0 Body ECU left of steering column. White F 0 DS+ TL Directed. All rights reserved.

21 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). THTON (optional T-Harness) Diagnostic OBDII Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Tire Pressure Warning ECU (white conn. on Body ECU) SIL: Blue, pin Body ECU Body ECU (middle conn. left side of steering column) 0 0 RDA: Pink, pin 0 RDA: Orange/Black Siren -pin White (+) Siren Output: Brown/Red: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) MAIN (A) (+) SIL Interrupt (conn. side): Blue SIL Interrupt (veh. side): Blue/White Hood Pin (-) Hood Input: Gray: -pin Black 0 IGN (0A) (+) DS+ Proper Fuse Positioning (-) RLY/PK LIGHT(A) (+) DS Autolight: Violet or Red, pin Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White 0-pin White 0 DS 0 0 Slide to open DS+ Headlight Switch It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

22 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU Body ECU (middle conn. left side of steering column) Diagnostic OBDII HS CAN High: Gray, pin HS CAN Low: White, pin SIL Data: Black, pin HS CAN Low : Tan: 0 0 Tire Pressure Warning ECU (white conn. on Body ECU) 0 SIL: Blue, pin Ignition RDA: Pink, pin (+) V: Black, pin Dash Fuse Box (white conn.) Autolight: Violet or Red, pin 0 0 Headlight Switch Siren Hood Pin HS CAN High : Tan/Black: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (veh. side): Blue/White: SIL Interrupt (conn. side): Blue: (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS DS+ Refer to the Vehicle Wiring Reference Information for wire and connector details. It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

23 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Yaris Hatchback (H Key) 0-0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Yaris Hatchback (H Key) W/ OEM Alarm 0-0 HS CAN High Gray Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Black Data OBDII. White A RDA Pink Data Middle Plug main body ECU left of steering column. White 0 B Autolights Violet or Red Headlight switch. White 0 C Accessory Blue (+) Ignition switch. White D Ignition Pink (+) Ignition switch. White D Ignition Lt.Blue (+) Ignition switch. White D Starter Green (+) Ignition switch. White D V Black (+) Dash fuse box. White E SIL Interrupt Blue Main Body ECU left of steering column. White F DS+ TL Directed. All rights reserved.

24 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Tire Pressure Warning ECU (white conn. on Body ECU) SIL: Blue, pin Body ECU 0 RDA: Pink or Lt. Green, pin 0 0 Body ECU (middle conn. left side of steering column) RDA: Orange/Black SIL Interrupt (conn. side): Blue Siren Hood Pin -pin White (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning DS MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) Autolight: Violet or Red, pin SIL Interrupt (veh. side): Blue/White Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White 0-pin White 0 DS 0 0 Slide to open DS+ Headlight Switch It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

25 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Tire Pressure Warning ECU (white conn. on Body ECU) Body ECU Body ECU (middle connector left side of steering column) HS CAN High: Gray, pin SIL Data: Black, pin Diagnostic OBDII SIL: Blue, pin 0 0 RDA: Pink or Lt. Green, pin 0 HS CAN Low: White, pin Siren Hood Pin HS CAN Low : Tan: HS CAN High : Tan/Black: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (veh. side): Blue/White: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS (+) V: Black, pin Dash Fuse Box (one pin white conn.) Ignition Autolight: Violet or Red, pin 0 0 Headlight Switch SIL Interrupt (conn. side): Blue: (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 Proper Fuse Positioning Slide to open DS DS+ Refer to the Vehicle Wiring Reference Information for wire and connector details. It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

26 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Yaris Hatchback (H Key) w/o OEM Alarm 0-0 THTON Toyota Prius c (H Key) 0-0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Yaris Hatchback (H Key) W/O OEM Alarm 0-0 HS CAN High Gray Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Black Data OBDII. White A RDA Pink Data Middle Plug main body ECU left of steering column. White 0 B Autolights Violet or Red Headlight switch. White 0 C Accessory Blue (+) Ignition switch. White D Ignition Pink (+) Ignition switch. White D Ignition Lt.Blue (+) Ignition switch. White D Starter Green (+) Ignition switch. White D V Black (+) Dash fuse box. White E SIL Interrupt Blue Main Body ECU left of steering column. White F Prius c (H Key) 0-0 HS CAN High Gray Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Black Data OBDII. White A RDA Lt.Green Data Middle Plug main body ECU left of steering column. White 0 B Autolights Red Headlight switch. White 0 C Accessory Blue (+) Ignition switch. White D Ignition Pink (+) Ignition switch. White D Ignition Lt.Blue (+) Ignition switch. White D Starter Green (+) Ignition switch. White D V Black (+) Dash fuse box. White E SIL Interrupt Blue Main Body ECU left of steering column. White F DS+ TL Directed. All rights reserved.

27 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). THTON (optional T-Harness) Body ECU Diagnostic OBDII Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition 0 RDA: Lt. Blue, pin 0 0 Body ECU (under main body ECU next to fuse box cover) HS CAN High: Pink, pin Steering Sensor HS CAN Low: White, pin RDA: Orange/Black HS CAN High : Orange/Green HS CAN Low : Orange/Brown Autolight Interrupt (veh. side): Lt. Green Siren -pin White (+) Siren Output: Brown/Red: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) MAIN (A) (+) Autolight: Green, pin Headlight Switch Tire Pressure Warning (blue conn. in passenger kick panel) 0 0 Autolight Interrupt (conn. side): Lt. Green/White SIL Interrupt (conn. side): Blue SIL Interrupt (veh. side): Blue/White Hood Pin (-) Hood Input: Gray: -pin Black 0-pin White 0 0 IGN (0A) (+) DS+ Proper Fuse Positioning (-) RLY/PK LIGHT(A) (+) DS DS SIL: Tan, pin Slide to open DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

28 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Steering Sensor HS CAN High: SIL Data: Green, pin Black, pin Diagnostic OBDII Body ECU 0 Body ECU (under main body ECU next to fuse box cover) RDA: Lt. Blue, pin 0 HS CAN High: Pink, pin 0 HS CAN Low: White, pin HS CAN Low: White, pin Siren Hood Pin HS CAN Low : Tan: HS CAN High : Tan/Black: HS CAN Low : Orange/Brown: HS CAN High : Oange/Green: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) 0 0 SIL: Tan, pin Tire Pressure Warning (blue conn. in passenger kick panel) (+) V: White, pin Dash Fuse Box (one pin white conn.) 0 0 Autolight: Green, pin 0 Headlight Switch SIL Interrupt (veh. side): Blue/White: SIL Interrupt (conn. side): Blue: (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 DS+ Proper Fuse Positioning Slide to open DS DS DS+ Ignition It is important to check that the fuses are positioned correctly. Refer to the Vehicle Wiring Reference Information for wire and connector details. DS+ TL Directed. All rights reserved.

29 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota RAV (H Key) 0-0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. RAV (H Key) 0-0 HS CAN High Black Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Green Data OBDII. White A HS CAN High Pink Data Steering sensor connector. Black G HS CAN Low White Data Steering sensor connector. Black G RDA Lt. Blue Data Below drivers fuse box. White 0 B Autolights Green 0 Headlight switch. Black 0 C SIL Interrupt Tan Passenger kick panel. Blue 0 F Accessory Red (+) Ignition switch. White D Ignition White (+) Ignition switch. White D Ignition Pink (+) Ignition switch. White D Starter White (+) Ignition switch. White D V White (+) Dash fuse box. White E DS+ TL Directed. All rights reserved.

30 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Body ECU RDA: Orange/Black 0 0 Autolight: Violet, pin 0 Headlight Switch RDA: Green, pin HS CAN High: Black or Green, pin 0 Tire Pressure Warning (white conn. on dash fuse box) HS CAN Low: White, pin 0 Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White 0 Body ECU (under main body ECU next to fuse box cover) SIL: Blue, pin HS CAN High: Orange/Green HS CAN Low: Orange/Brown SIL Interrupt (conn. side): Blue SIL Interrupt (veh. side): Blue/White Siren Hood Pin -pin White (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black 0-pin White 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS DS+ It is important to check that the fuses are positioned correctly. 0 DS+ TL Directed. All rights reserved.

31 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU Body ECU (under main body ECU next to fuse box cover) HS CAN High: Red, pin SIL Data: Lt. Green, pin Diagnostic OBDII Tire Pressure Warning (white conn. on dash fuse box) SIL: Blue, pin RDA: Green, pin 0 HS CAN High: Black or Green, pin 0 HS CAN Low: White, pin 0 HS CAN Low: White, pin HS CAN Low: Tan: HS CAN High: Tan/Black: HS CAN Low: Orange/Brown: HS CAN High: Orange/Green: RDA: Orange/Black: SIL Data: Yellow/Black: Siren Hood Pin (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (veh. side): Blue/White: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ DS MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) (+) V: White, pin Dash Fuse Box (one pin white conn.) Autolight: Violet, pin Headlight Switch Ignition Refer to the Vehicle Wiring Reference Information for wire and connector details. SIL Interrupt (conn. side): Blue: (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 Proper Fuse Positioning Slide to open DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

32 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Corolla (H Key) 0 THTON Toyota Corolla IM (H Key) 0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Corolla (H Key) 0 HS CAN High Red Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Lt. Green Data OBDII. White A HS CAN High Black Data Body ECU. White 0 B HS CAN Low White Data Body ECU. White 0 B RDA Green Data Body ECU. White 0 B Autolights Violet 0 Headlight switch. Black 0 C SIL Interrupt Blue Dash Fuse Box. White 0 F Accessory Black (+) Ignition switch. White D Ignition Gray (+) Ignition switch. White D Ignition Green (+) Ignition switch. White D Starter White (+) Ignition switch. White D V White (+) Dash fuse box. White E Corolla IM (H Key) 0 HS CAN High Red Data OBDll. White A HS CAN Low White Data OBDll. White A SIL Lt.Green Data OBDll. White A HS CAN High Green Data Body ECU. White 0 B HS CAN Low White Data Body ECU. White 0 B RDA Green Data Body ECU. White 0 B Autolights Violet 0 Headlight switch. White 0 C SIL Interrupt Blue Dash Fuse Box. White 0 F Accessory Black (+) Ignition switch. White D Ignition Gray (+) Ignition switch. White D Ignition Green (+) Ignition switch. White D Starter White (+) Ignition switch. White D V White (+) Dash fuse box. White E DS+ TL Directed. All rights reserved.

33 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition RDA: Orange/Black HS CAN RDA: Lt. Green, pin High: Tan, pin HS CAN Low: White, pin Body ECU (under main body ECU next to fuse box cover) Autolight: Red, pin 0 0 Headlight Switch HS CAN High: Orange/Green HS CAN Low: Orange/Brown Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White SIL Interrupt (veh. side): Blue/White SIL Interrupt (conn. side): Blue Siren Hood Pin -pin White (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning DS MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) SIL: Blue, pin pin White 0 DS Slide to open DS+ Tire Pressure Warning (white conn. on Body ECU) It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

34 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU (under main body ECU next to fuse box cover) Tire Pressure Warning (white conn. on Body ECU) HS CAN High: Gray, pin SIL Data: Black, pin Diagnostic OBDII SIL: Blue, pin RDA: HS CAN Lt. Green, pin High: Tan, pin HS CAN Low: White, pin HS CAN Low: White, pin Siren Hood Pin HS CAN Low: Tan: HS CAN High: Tan/Black: HS CAN Low: Orange/Brown: HS CAN High: Orange/Green: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (veh. side): Blue/White: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ DS MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) (+) V: Black, pin Dash Fuse Box (one pin white conn.) Autolight: Red, pin 0 0 Headlight Switch Ignition Refer to the Vehicle Wiring Reference Information for wire and connector details. SIL Interrupt (conn. side): Blue: (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 Proper Fuse Positioning Slide to open DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

35 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Prius c (H Key) 0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Prius c (H Key) 0 HS CAN High Gray Data OBDll. White A HS CAN Low White Data OBDll. White A SIL Black Data OBDll. White A HS CAN High Tan Data Body ECU. White 0 B HS CAN Low White Data Body ECU. White 0 B RDA Lt. Green Data Body ECU. White 0 B Autolights Red Headlight switch. White 0 C SIL Interrupt Blue Body ECU. White F Accessory Blue (+) Ignition switch. White D Ignition Pink (+) Ignition switch. White D Ignition Lt. Blue (+) Ignition switch. White D Starter Green (+) Ignition switch. White D V Black (+) Dash fuse box. White E DS+ TL Directed. All rights reserved.

36 Type 0 with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). THTON (optional T-Harness) Headlight Switch Steering Sensor Diagnostic OBDII Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition 0 0 HS CAN High: Yellow, pin HS CAN Low: White, pin HS CAN Low: Orange/Brown Autolight: White, pin 0 HS CAN High: Orange/Green SIL: Lt. Green, pin Body ECU 0 RDA: Black, pin Autolight Interrupt (conn. side): Lt. Green/White 0 (-) Parking Light Output: Green, pin 0 Body ECU (middle connector left side of steering column) Autolight Interrupt (veh. side): Lt. Green SIL Interrupt (veh. side): Blue/White SIL Interrupt (conn. side): Blue RDA: Orange/Black Siren Hood Pin -pin White (-) Parking Light Output: Lt. Green/Black: (-) Lock Output: Dk. Green/Black: (-) Unlock Output: Dk. Blue/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS Tire Pressure Warning ECU (white conn. on Body ECU) White (drivers kick panel or rear of dash fuse box) (-) Lock: Pink, pin 0 (-) Unlock: Yellow, pin OR (-) Lock: Red, pin (-) Unlock: Yellow, pin 0 0 White (drivers kick panel or rear of dash fuse box) OR 0-pin White 0 Slide to open DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

37 Type 0 Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU Body ECU (middle conn. left side of steering column) (-) Lock: Pink, pin OR (-) Unlock: Yellow, pin (-) Lock: Red, pin White (drivers kick panel or rear of dash fuse box) RDA: Black, pin (-) Unlock: Yellow, pin 0 0 White (drivers kick panel or rear of dash fuse box) Tire Pressure Warning ECU (white conn. on Body ECU) SIL: Lt. Green, pin (-) Parking Lights: Green, pin OR Ignition Refer to the Vehicle Wiring Reference Information for wire and connector details. HS CAN High: Yellow, pin Steering Sensor HS CAN Low: White, pin Autolight: White, pin Headlight Switch Siren HS CAN Low: White, pin Hood Pin HS CAN High: Blue, pin SIL Data: White, pin HS CAN Low: Tan: HS CAN High: Tan/Black: HS CAN Low: Orange/Brown: HS CAN High: Orange/Green: RDA: Orange/Black: SIL Data: Yellow/Black: (-) Parking Light Output: Lt. Green/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: (+) Starter Output: White: & (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Lock Output: Dk. Green/Black: (-) Unlock Output: Dk. Blue/Black: SIL Interrupt (veh. side): Blue/White: SIL Interrupt (conn. side): Blue: Diagnostic OBDII (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

38 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Tacoma (H Key) 0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Tacoma (H Key) 0 HS CAN High Blue Data OBDII. White A HS CAN Low White Data OBDII. White A SIL White Data OBDII. White A HS CAN High Yellow Data Steering sensor connector. White G HS CAN Low White Data Steering sensor connector. White G RDA Black Data Middle Plug main body ECU left of steering column. White 0 B Parking Lights Green (-) Middle Plug main body ECU left of steering column. White 0 B Autolights White 0 Headlight switch White 0 C Accessory Red (+) Ignition switch. White D Ignition Black (+) Ignition switch. White D Ignition White (+) Ignition switch. White D Starter Green (+) Ignition switch. White D Starter Violet (+) Ignition switch. White D V Red (+) Ignition switch. White D Lock "Red (without window jam protection) or Pink (with window jam protection)" or 0 (-) Drivers kick panel or rear of dash fuse box. White or H Unlock "Yellow (without window jam protection) or yellow (with window jam protection)" 0 or (-) Drivers kick panel or rear of dash fuse box. White or SIL Interrupt Lt. Green Main Body ECU left of steering column. White F H DS+ TL Directed. All rights reserved.

39 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). THTON (optional T-Harness) Steering Sensor Diagnostic OBDII Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Body ECU HS CAN High: Pink, pin 0 HS CAN Low: White, pin RDA: Pink, pin (-) Trunk Release: Blue, pin 0 0 HS CAN Low: Orange/Brown HS CAN High: Orange/Green RDA: Orange/Black (-) Trunk Release Output: Red/White Body ECU (middle connector left side of steering column) Siren -pin White (+) Siren Output: Brown/Red: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) MAIN (A) (+) Dash Fuse Box (white conn.) SIL: Blue, pin Autolight: Violet or Red, pin 0 0 Headlight Switch SIL Interrupt (conn. side): Blue/White SIL Interrupt (veh. side): Blue Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White Hood Pin (-) Hood Input: Gray: -pin Black 0-pin White 0 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open (-) RLY/PK LIGHT(A) (+) DS DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

40 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Steering Sensor HS CAN High: Gray, pin SIL Data: Black, pin Diagnostic OBDII Body ECU 0 RDA: Pink, pin 0 HS CAN High: Pink, pin 0 HS CAN Low: White, pin Body ECU (middle connector left side of steering column) HS CAN Low: White, pin HS CAN Low: Tan: HS CAN High: Tan/Black: Siren HS CAN Low: Orange/Brown: HS CAN High: Orange/Green: RDA: Orange/Black: SIL Data: Yellow/Black: (-) Trunk Release Output: Red/White: (+) Siren Output: Brown/Red: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) MAIN (A) (+) (-) Trunk Release: Blue, pin Hood Pin (-) Hood Input: Gray: SIL Interrupt (conn. side): Blue/White: 0 IGN (0A) (+) DS+ (-) RLY/PK LIGHT(A) (+) DS Dash Fuse Box (white conn.) SIL: Blue, pin Dash Fuse Box (white conn.) Ignition (+) V: Black, pin Refer to the Vehicle Wiring Reference Information for wire and connector details. Autolight: Violet or Red, pin 0 0 Headlight Switch SIL Interrupt (veh. side): Blue: (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 Proper Fuse Positioning Slide to open DS DS+ It is important to check that the fuses are positioned correctly. 0 DS+ TL Directed. All rights reserved.

41 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Yaris Hatchback (H Key) w/ OEM Alarm 0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Yaris Hatchback (H Key) w/ OEM Alarm 0 HS CAN High Gray Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Black Data OBDII. White A HS CAN High Pink Data Steering sensor connector. White G HS CAN Low White Data Steering sensor connector. White G RDA Pink Data Middle Plug main body ECU left of steering column. White 0 B Trunk Release Blue (-) Middle Plug main body ECU left of steering column. White 0 B Autolights Violet or Red Headlight switch. White 0 C SIL Interrupt Blue Dash fuse box. White F Accessory Blue (+) Ignition switch. White D Ignition Pink (+) Ignition switch. White D Ignition Lt.Blue (+) Ignition switch. White D Starter Green (+) Ignition switch. White D V Black (+) Dash fuse box. White E DS+ TL Directed. All rights reserved.

42 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). THTON (optional T-Harness) Steering Sensor Diagnostic OBDII Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Body ECU HS CAN High: Pink, pin HS CAN Low: White, pin HS CAN Low: Orange/Brown HS CAN High: Orange/Green Dash Fuse Box (white conn.) SIL: Blue, pin RDA: Pink, pin 0 0 Autolight: Violet or Red, pin 0 0 Headlight Switch Body ECU (middle connector left side of steering column) (-) Trunk Release: Blue, pin RDA: Orange/Black (-) Trunk Release Output: Red/White SIL Interrupt (conn. side): Blue/White SIL Interrupt (veh. side): Blue Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White Siren Hood Pin -pin White (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black 0-pin White 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

43 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU Dash Fuse Box (white conn.) SIL: Blue, pin 0 RDA: Pink, pin 0 Dash Fuse Box (white conn.) Ignition (+) V: Black, pin Refer to the Vehicle Wiring Reference Information for wire and connector details. 0 Steering Sensor HS CAN High: Pink, pin Body ECU (middle connector left side of steering column) (-) Trunk Release: Blue, pin HS CAN Low: White, pin Autolight: Violet or Red, pin 0 0 Headlight Switch Siren Hood Pin HS CAN High: Gray, pin HS CAN Low: White, pin SIL Data: Black, pin Diagnostic OBDII HS CAN Low: Tan: HS CAN High: Tan/Black: HS CAN Low: Orange/Brown: HS CAN High: Orange/Green: RDA: Orange/Black: SIL Data: Yellow/Black: (-) Trunk Release Output: Red/White: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (conn. side): Blue/White: SIL Interrupt (veh. side): Blue: (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

44 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Yaris Hatchback (H Key) w/o OEM Alarm 0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Yaris Hatchback (H Key) w/o OEM Alarm 0-0 HS CAN High Gray Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Black Data OBDII. White A HS CAN High Pink Data Steering sensor connector. White G HS CAN Low White Data Steering sensor connector. White G RDA Pink Data Middle Plug main body ECU left of steering column. White 0 B Trunk Release Blue (-) Middle Plug main body ECU left of steering column. White 0 B Autolights Violet or Red Headlight switch. White 0 C SIL Interrupt Blue Dash Fuse Box White F Accessory Blue (+) Ignition switch. White D Ignition Pink (+) Ignition switch. White D Ignition Lt.Blue (+) Ignition switch. White D Starter Green (+) Ignition switch. White D V Black (+) Dash fuse box. White E DS+ TL Directed. All rights reserved.

45 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition SIL: Yellow, pin 0 Body ECU RDA: Lt. Green, pin 0 HS CAN High: Red, pin HS CAN Low: White, pin 0 0 Body ECU (under main body ECU next to fuse box cover) Autolight: Black, pin 0 RDA: Orange/Black HS CAN High: Orange/Green HS CAN Low: Orange/Brown SIL Interrupt (conn. side): Blue/White SIL Interrupt (veh. side): Blue Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White Siren Hood Pin -pin White (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black 0-pin White 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning DS MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS Dash Fuse Box (white conn.) 0 0 Headlight Switch Slide to open DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

46 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). HS CAN High: Red, pin HS CAN Low: White, pin HS CAN High: SIL Data: Lt. Blue, pin Violet, pin Diagnostic OBDII Dash Fuse Box (white conn.) SIL: Yellow, pin 0 0 Ignition 0 RDA: Lt. Green, pin Refer to the Vehicle Wiring Reference Information for wire and connector details. 0 Body ECU (under main body ECU next to fuse box cover) Autolight: Black, pin Headlight Switch Siren HS CAN Low: White, pin Hood Pin HS CAN Low: Tan: HS CAN High: Tan/Black: HS CAN Low: Orange/Brown: HS CAN High: Orange/Green: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (conn. side): Blue/White: SIL Interrupt (veh. side): Blue: (+) Starter Output: White: & (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

47 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Highlander (H Key) 0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Highlander (H Key) 0 HS CAN High Violet Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Lt. Blue Data OBDII. White A HS CAN High Red Data Middle Plug main body ECU left of steering column. White 0 B HS CAN Low White Data Middle Plug main body ECU left of steering column. White 0 B RDA Lt. Green Data Middle Plug main body ECU left of steering column. White 0 B Autolights Black 0 Headlight Switch. White 0 C SIL Interrupt Yellow 0 Dash Fuse Box. White F Accessory Gray (+) Ignition switch. White D Ignition Black (+) Ignition switch. White D Ignition Green (+) Ignition switch. White D Starter Blue (+) Ignition switch. White D Starter Gray (+) Ignition switch. White D V Black (+) Ignition switch. White D DS+ TL Directed. All rights reserved.

48 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU Body ECU (under main body ECU next to fuse box cover) Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition RDA: Lt. Green, pin RDA: Orange/Black Autolight: White, pin 0 SIL: Lt. Blue, pin Headlight Switch 0 0 (-) Parking Light: Yellow, pin Tire Pressure Warning ECU (white conn. in Driver Kick Panel) HS CAN High: Brown, pin Steering Sensor HS CAN Low: White, pin HS CAN High : Orange/Green HS CAN Low : Orange/Brown Autolight Interrupt (conn. side): Lt. Green/White Autolight Interrupt (veh. side): Lt. Green SIL Interrupt (conn. side): Blue/White SIL Interrupt (veh. side): Blue Siren Hood Pin -pin White (-) Parking Light Output: Lt. Green/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black 0-pin White 0 MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning Slide to open MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

49 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). 0 RDA: Lt. Green, pin 0 Steering Sensor 0 Siren Hood Pin HS CAN High: SIL Data: Lt. Blue, pin Red, pin Diagnostic OBDII Body ECU HS CAN Low: White, pin HS CAN HS CAN HS CAN Low : Tan: High: Brown, Low: White, HS CAN High : Tan/Black: Body ECU pin pin (under main body ECU HS CAN Low : Orange/Brown: next to fuse box cover) HS CAN High : Oange/Green: RDA: Orange/Black: SIL Data: Yellow/Black: (-) Parking Light Output: Lt. Green/ Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: SIL Interrupt (conn. side): Blue/White: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) DS SIL: Lt. Blue, pin (+) V: White, pin Dash Fuse Box (white conn.) 0 0 Autolight: White, pin 0 (-) Parking Light: Yellow, pin Headlight Switch Ignition SIL Interrupt (veh. side): Blue: (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 Proper Fuse Positioning Slide to open DS DS+ Tire Pressure Warning ECU (white conn. in Driver Kick Panel) It is important to check that the fuses are positioned correctly. Refer to the Vehicle Wiring Reference Information for wire and connector details. DS+ TL Directed. All rights reserved.

50 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota CH-R (H Key) 0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. CH-R (H Key) 0 HS CAN High Red Data OBDll White A HS CAN Low White Data OBDll White A SIL Lt. Blue Data OBDll White A HS CAN High Brown Data Steering sensor connector. Blue G HS CAN Low White Data Steering sensor connector. Blue G RDA Lt. Green Data Body ECU connector. White 0 B Autolights White 0 Headlight switch. White 0 C Parking Lights Yellow (-) Headlight switch. White 0 C Accessory Green (+) Ignition switch. White D Ignition Gray (+) Ignition switch. White D Starter Violet (+) Ignition switch. White D V Black/White (+) Dash Fuse Box. White E SIL Interrupt Lt. Blue Driver Kick Panel. White F 0 DS+ TL Directed. All rights reserved.

51 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Body ECU FUSES OR BODY ECU 0 RDA: Blue, pin 0 Body ECU (middle or underside conn. of ECU) 0 RDA: Orange/Black Siren -pin White (+) Siren Output: Brown/Red: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) MAIN (A) (+) SIL Interrupt (veh. side): Blue SIL Interrupt (conn. side): Blue/White Hood Pin (-) Hood Input: Gray: -pin Black 0 IGN (0A) (+) DS+ Proper Fuse Positioning (-) RLY/PK LIGHT(A) (+) DS 0 SIL: Yellow, pin Autolight: Green, pin 0 Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White 0-pin White 0 DS Tire Pressure Warning ECU (white conn. in passenger kick panel) 0 Slide to open DS+ 0 Headlight Switch It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

52 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Body ECU FUSES OR BODY ECU Body ECU (middle or underside conn.of ECU) HS CAN High: Blue, pin SIL Data: Gray, pin Diagnostic OBDII HS CAN Low: White, pin HS CAN Low : Tan: Tire Pressure Warning ECU (white conn. in passenger kick panel) 0 SIL: Yellow, pin RDA: Blue, pin Siren Hood Pin HS CAN High : Tan/Black: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: (-) Hood Input: Gray: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) SIL Interrupt (conn. side): Blue/White: SIL Interrupt (veh. side): Blue: (+) Starter Output: White: & DS+ Proper Fuse Positioning DS Ignition Refer to the Vehicle Wiring Reference Information for wire and connector details. Autolight: Green, pin Headlight Switch (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 Slide to open DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

53 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota Camry (H Key) 0-0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Camry (H Key) 0-0 HS CAN High Blue Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Gray Data OBDII. White A RDA Blue Data Middle Plug main body ECU left of steering column. White 0 B Autolights Green 0 Headlight switch. White 0 C Accessory White (+) Ignition switch. White D Ignition Black (+) Ignition switch. White D Ignition Pink (+) Ignition switch. White D Starter Blue (+) Ignition switch. White D Starter Lt. Green (+) Ignition switch. White D V Green (+) Ignition switch. White D SIL Interrupt Yellow Passenger Kick Panel. White F DS+ TL Directed. All rights reserved.

54 Type with T-Harness (THTON) Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). Diagnostic OBDII THTON (optional T-Harness) Refer to the "Vehicle wiring reference chart" for more specific T-harness compatibility. Ignition Tire Pressure Warning ECU (blue conn. in passenger kick panel) 0 0 SIL: Tan, pin Body ECU OR BODY ECU 0 FUSES RDA: Lt. Blue or Green, pin 0 Body ECU (middle or underside conn. of ECU) 0 RDA: Orange/Black SIL Interrupt (conn. side): Blue/White Siren Hood Pin -pin White (+) Siren Output: Brown/Red: (-) Hood Input: Gray: -pin Black MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) 0 IGN (0A) (+) DS+ Proper Fuse Positioning DS MAIN (A) (+) (-) RLY/PK LIGHT(A) (+) SIL Interrupt (veh. side): Blue Autolight Interrupt (veh. side): Lt. Green Autolight Interrupt (conn. side): Lt. Green/White Autolight: Green, pin 0 0-pin White 0 DS 0 0 Slide to open DS+ Headlight Switch It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

55 Type Refer to "Pre-installation and application warnings" on page for important information, such as the description of special notes referenced in the diagram ( ). FUSES BODY ECU Body ECU (Body Ecu on back of dash fuse box) HS CAN High: Black, pin SIL Data: Green, pin Diagnostic OBDII HS CAN Low: White, pin HS CAN Low : Tan: Tire Pressure Warning ECU (blue conn. in passenger kick panel) 0 0 RDA: Lt. Blue or Green, pin Siren HS CAN High : Tan/Black: RDA: Orange/Black: SIL Data: Yellow/Black: (+) Siren Output: Brown/Red: MAIN (A) (+) (-) RLY PK LIGHT (A) (+) 0 (-) ACC & START (0A) (+) 0 (-) FLEX RLY (0A) (+) MAIN (A) (+) SIL: Tan, pin Hood Pin (-) Hood Input: Gray: 0 IGN (0A) (+) (-) RLY/PK LIGHT(A) (+) (+) V: White, pin Dash Fuse Box (white conn.) Ignition Refer to the Vehicle Wiring Reference Information for wire and connector details. 0 Autolight: Green, pin 0 0 Headlight Switch SIL Interrupt (conn. side): Blue/White: SIL Interrupt (veh. side): Blue: (+) Starter Output: White: & (+) V Input: Red: & Autolight Interrupt (veh. side): Lt. Green: Autolight Interrupt (conn. side): Lt. Green/White: (-) Ground: Black: 0 (+) V Input: Red/Black: (+/-) Flex Output: Pink/White: (+) V Ignition Input: Red: Starter Disable (key side): Green: (+) V Starter Output (starter side): Violet: (+) V Accessory Output: Orange: (+/-) Flex Input: Red/White: (+) Ignition Input/Ouput: Pink: 0 0 DS+ Proper Fuse Positioning Slide to open DS DS DS+ It is important to check that the fuses are positioned correctly. DS+ TL Directed. All rights reserved.

56 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. T-Harness compatibility Vehicle Year T-Harness Toyota RAV (H Key) 0-0 THTON Wire Information Information Function Color Pin Polarity Location Color Pins Ref. RAV (H Key) 0-0 HS CAN High Black Data OBDII. White A HS CAN Low White Data OBDII. White A SIL Green Data OBDII. White A RDA Lt. Blue or Green Data Body ECU on back of dash fuse box. White 0 B Autolights Green 0 Headlight switch. White 0 C Accessory Red (+) Ignition switch. White D Ignition White (+) Ignition switch. White D Ignition Pink (+) Ignition switch. White D Starter White (+) Ignition switch. White D V White (+) Dash fuse box. White E SIL Interrupt Tan Passenger Kick Panel. Blue 0 F DS+ TL Directed. All rights reserved.