Directed Digital System

Size: px
Start display at page:

Download "Directed Digital System"

Transcription

1 Directed Digital System TL Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and components. 05 Directed, Vista, CA Directed Digital System 06-0

2 Contents Warning! Safety first... 3 Introduction... 4 Vehicle application guide... 4 OEM Remote Starter Detection... 6 Wiring connections... 7 Main power harness (H), -pin thick gauge connector... 7 Analog harness (H3), 8-pin white connector... 8 MC50 harness (H4), 8 thick-gauge wires (optional)... 8 Installation... 9 Type (Key-Type Vehicles with CAN)... 9 Type a (Push-to-Start Vehicles with CAN)... 0 Type b - with T-Harness THTLC (Push-to-Start Vehicles with CAN)... Type 3a -Without T-Harness THTLC (Push-to-Start Vehicles with CAN)... Type 3b - with T-Harness THTLC (Push-to-Start Vehicles with CAN)... 3 Type 4 (Key-Type Vehicles without CAN)... 4 Type 5 (Push-to-Start Vehicles without CAN)... 5 Type 6 (Push-to-Start Vehicles with Keyport without CAN)... 6 Vehicle wiring reference charts... 7 Pit Stop/ Idle Mode... 7 Installation Type... 7 Installation Type... 9 Installation Type Installation Type 4... Installation Type Installation Type Connecting the module... 6 Important!... 6 Manual or automatic transmission selection... 6 Optional sensors... 7 RF kits... 7 When used in conjunction with SmartStart... 7 Module programming... 8 LED diagnostics and troubleshooting... 3 Module reset Hard reset Learning the Tach (not needed with Virtual Tach) Initializing Virtual Tach (not needed with hardwired or data tach applications) Limited lifetime consumer warranty Quick Reference Guide Viper, Clifford, Python, Avital Automate (Regular Key) Quick Reference Guide Autostart (Regular Key) Quick Reference Guide Viper, Clifford, Python, Avital Automate (Smart Key)... 4 Quick Reference Guide Autostart (Smart Key)... 43

3 Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, () Never remotely start the vehicle with the vehicle in gear, and () Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. 3

4 Introduction The TL firmware for Directed Digital Systems is a complete solution for remote start, security (if applicable), bypass interface, and convenience needs compatible with specific Toyota and Scion vehicles. Warning! This module can only be programmed via the web tool, which can be found on or using the Directechs Mobile application for smartphones. Features and functions will become accessible when you connect the module using the XKLoader. Vehicle application guide The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security Lexus ES ES 350 (Smart Key) GS 300 (Smart Key) 5 GS 350 (Smart Key) 5 5 GS 430 (Smart Key) 5 5 GS 450h (Smart Key) 5 5 GS 460 (Smart Key) 5 GX IS 50 (Smart Key) IS 350 (Smart Key) IS F (Smart Key) 5 LS LS 460 (Smart Key) 5 5 LS 600h (Smart Key) 5 LX RX RX RX 400h Pontiac Vibe Vibe 4 Scion tc xb xd Legend: PK: Transponder Immobilizer Override DL: OE Door Lock Alarm Controls RS: Remote Start Engine Controls SS: Integrated Security Monitoring ST: Function/Feature Status DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Hatch Glass Release DL-Trunk / Hatch Release RS-3x LOCK START (Start control using OEM Remote) RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-E-Brake Status ST-Ignition Status 4

5 Vehicles PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Hatch Glass Release DL-Trunk / Hatch Release RS-3x LOCK START (Start control using OEM Remote) RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-E-Brake Status ST-Ignition Status Toyota 4Runner Avalon Avalon (Smart Key) Camry Camry Camry (Smart Key) Camry Hybrid Corolla Corolla Corolla (Smart Key) FJ Cruiser Highlander Highlander Highlander (Smart Key) Highlander Hybrid Highlander Hybrid 4 4 Land Cruiser Land Cruiser (Smart Key) Matrix Matrix Prius (Smart Key) RAV4 RAV4 4 4 RAV4 (Smart Key) Sequoia Sienna Solara Tacoma Tundra Venza 4 Yaris Yaris Sedan Legend: PK: Transponder Immobilizer Override DL: OE Door Lock Alarm Controls RS: Remote Start Engine Controls SS: Integrated Security Monitoring ST: Function/Feature Status No takeover feature is available on Push-to-Start vehicles. If equipped, OE remote start must be remoted before installaton. See page 6 for more information. Key Types Some Toyota 00+ models have different encryption types. Please look at your key blade and identify the markings. A dot. means the vehicle is compatible with TL firmware. G or H indicates the vehicle is not Some Toyota 00+ models have different encryption types. Please lookat your key blade and identify the markings. compatible A dot. means with the this vehicle firmware. is compatible with TL firmware. G or H indicates the vehicle is not compatible with this firmware. Standard Key G-stamped keys H-stamped keys For vehicles with G-stamped key, see TL4, TL5 or TL7 firmware. TL works only with standard key. For vehicles with H-stamped key, see TL0 firmware. TL works only with standard key. H 5

6 OEM Remote Starter Detection How to Know if the vehicle is Equipped with an OEM Remote Starter - An ENGINE STARTER sticker should be on the remote. - Remote start the OEM remote starter: Press the remote control s lock button twice within seconds, then press and hold the lock button for 3 seconds. The parking lights flash after 3 seconds. The engine starts and the parking lights flash repeatedly for 0 seconds. ENGINE STARTER x Press Hold for 3 seconds If the Vehicle is Equipped with an OEM Remote Starter If the vehicle is equipped with an OEM remote starter, the Directed Digital System LED will start flashing orange to indicate its detection. To skip bypass and use convenience only, press the programming button 5 times.* The reason for this is to allow aftermarket security to be installed while keeping the factory remote starter active. If you wish to use Directed Digital System to control the remote start sequence, the factory remote starter must be disconnected before programming the Directed Digital System as both modules cannot coexist. * The Directed Digital System LED turns ON solid orange for 3 seconds after programming or power up to indicate the bypass is not active. Refer to "LED diagnostics and troubleshooting" starting on page 3 for more information. Locating the OEM Remote Starter Vehicle Toyota Camry (key) Toyota Corolla (key) Toyota Highlander (key) Toyota Matrix (key) Pontiac Vibe (key) Scion xb (key) Scion xd (key) Toyota Rav4 (key) Toyota Sequoia (key) Toyota Tundra (key) Toyota Yaris (key) Toyota Corolla (Smart Key) Toyota Rav4 (Smart Key) Toyota Camry (Smart Key) Toyota Camry Hybrid (Smart Key) Toyota Highlander (Smart Key) Toyota Highlander Hybrid (Smart Key) OEM Remote Starter Connector Location Behind Glove Box Passenger kick panel Behind Glove Box Passenger kick panel Junction Box Steering column Behind Glove Box Steering column Junction Box Behind Glove Box Passenger kick panel Behind Glove Box Junction Box Passenger kick panel Behind Glove Box Passenger kick panel Junction Box Steering column Behind Glove Box Passenger kick panel Junction Box Steering column Behind Glove Box Passenger kick panel Junction Box Steering column Behind Glove Box Passenger kick panel Steering column Behind GloveBox Passenger kick panel Steering column Behind Glove Box Junction Box Steering column Behind Glove Box Passenger kick panel Junction Box Steering column Behind Glove Box Junction Box Behind Glove Box Passenger kick panel Behind Glove Box Passenger kick panel Behind Glove Box Passenger kick panel Behind Glove Box Passenger kick panel 6

7 Wiring connections The wiring connections listed below are specific to this firmware. Main power harness (H), -pin thick gauge connector Conn./Pin Color Description H/ White Relay 3 COM Clutch Bypass Output (Type 4) H/ White/Brown Relay 3 N.O. Clutch Bypass Input (Type 4) H/3 Brown/Red Relay N.O. No Connection H/4 Yellow/Red Relay COM Autolight Off (Type 4) H/5 Orange/Red Relay N.C. Autolight Off (Type 4) H/6 Yellow Relay COM Starter (Type ); STSW (Types 3); Brake (Types 5 6) H/7 White Relay 3 COM Clutch Bypass Output (Type 4) H/8 White/Brown Relay 3 N.O. Clutch Bypass Input (Type 4) H/9 Black (-) Ground H/0 Red (+) Volt (Battery) H/ Orange/Yellow Relay N.C. Brake (Types 5 6) H/ Brown Relay N.O. (+) V (Types -3, 5 6) Auxiliary output harness (H), 6-pin black connector Conn./Pin Color Description H/ Violet/Brown No Connection H/ Yellow/Black Data TX (Types, 4-6) H/3 Orange/Black Data RX (Types, 4-6) H/4 Tan HS CAN Low (Types -3) H/5 Tan/Black HS CAN High (Types -3) H/6 Light Green No Connection H/7 Orange/Green No Connection H/8 Orange/Brown No Connection H/9 Violet/Green No Connection H/0 Green/Black (-) Parking Lights H/ White/Violet No Connection H/ White/Red (+) No Connection H/3 Lt. Blue/Black (-) Push-To-Start (PTS) Output (Types, 3, 5 6) H/4 Green/Red No Connection H/5 N/A No Connection H/6 Violet/Yellow No Connection. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 7

8 Analog harness (H3), 8-pin white connector Conn./Pin Color Description H3/ Lt. Blue/Red No Connection H3/ Black/White (-) Parking Brake Input (Manual Transmission) H3/3 Gray (-) Hood Input H3/4 N/A No Connection H3/5 Gray/Black (+) Glow Plug Input H3/6 Violet/White (AC) Tach Input H3/7 Dark Blue No Connection H3/8 Brown/Black No Connection H3/9 Red/White No Connection H3/0 White/Green (-) Door Input H3/ Yellow/Green (+) Door Input H3/ Blue/Red No Connection H3/3 Light Blue (-) Trunk Trigger Input H3/4 Pink/Yellow (-) Activation (Start Trigger) Input H3/5 Dark Green No Connection H3/6 Brown/White (+) Brake Input H3/7 Brown (+) Siren Output H3/8 Blue/White (-) Active When Running (Status) Output MC50 harness (H4), 8 thick-gauge wires (optional) Conn./Pin Color Description H4/ Pink/White (+) Ignition /Flex Relay Output 3 H4/ Red/White (+) Fused (30A) Ignition /Flex Relay Input H4/3 Pink (+) Ignition Output (Also Input to Yellow in Ribbon Cable) H4/4 Red (+) Volt (Battery) Input H4/5 Orange (+) Accessory Output H4/6 Red (+) Volt (Battery) Input H4/7 Green Starter Input (From Key Switch) 4 H4/8 Violet (+) Starter Output (To Starter). If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary.. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" starting on page 4 for a list of compatible features. 3. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 4. The Green wire is only required for starter kill and antigrind applications. 8

9 Installation Type (Key-Type Vehicles with CAN) Refer to "Vehicle wiring reference charts" starting on page 7 for more information on vehicle-specific connections. White Connector Headlight Switch Scion XD and Toyota Yaris Headlight Switch Black Connector Immobilizer DATA RX: pin Diagnostic Connector at OBDII HS CAN High: pin 6 Manual/Auto. Transmission Type Prog. Button Autolight, pin (+) Starter Output (to starter): Violet [] Starter Input (from key switch): Green (+) V Input: Red (+) Accessory Output: Orange (+) V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) Fused (30A) Ignition / Flex Relay Input: Red/White (+) Ignition /Flex Relay Output: Pink/White Ignition Connector OR Parking Lights, pin 8 Refer to the Vehicle Wiring Reference Information to determine the right connector for your vehicle. 8 thick-gauge wires Parking Lights, pin 3 MC50 4 White 7 White 9 HS CAN Low: pin DATA TX: Yellow/Black: DATA RX: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (-) Parking Lights Output: Green/Black: 0 Hood Pin Siren [] (-) Hood Input: Gray: 3 [3] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White Wh 6 Green Bk 4 White 4 Red White : Brown: (+) V 0: Red: (+) V 9: Black: (-) Ground 6: Yellow: (+) Starter DATA TX: pin 5 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 5: Orange/Red: Autolight Off 4: Yellow/Red: Autolight Off (+) V Refer to the Vehicle Wiring Reference Information for wire and connector details. Refer to for clutch wire colors, pin numbers and connector details. (+) Clutch : ONLY for Manual Transmission vehicles OR Manual Transmission: Connect to vehicle s clutch. OR Automatic Transmission: Connect to vehicle s starter. [] The Green wire is only required for starter kill and antigrind connections. [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. [3] The siren is only available with the remote start and security system. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 9

10 Type a (Push-to-Start Vehicles with CAN) Refer to "Vehicle wiring reference charts" starting on page 7 for more information on vehicle-specific connections. White Connector Headlight Switch Diagnostic Connector at OBDII HS CAN High: pin Parking Lights: pin 8 HS CAN Low: pin 4 HS CAN Low: Tan: 4 Manual/Auto. Transmission Type Prog. Button White connector at Fuse Box Black Connector ENGINE START STOP (-) Push-To-Start: pin Connection required only if Pit-Stop/Idle mode is desired (see details on the page 7). (connector side view) 8 Hood Pin Siren HS CAN High: Tan/Black: 5 (-) Parking Lights Output: Green/Black: 0 (-) Push-to-Start Output: Lt. Blue/Black: 3 [] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White Wh 6 Green Bk 4 White 4 Red White : Brown: (+) V 0: Red: (+) V Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 9: Black: (-) Ground 6: Yellow: (+) Starter Switch Wire Output 8: White/Brown: (+) Clutch Bypass Input 7: White: (+) Clutch Bypass Output Change Relay3 function to Starter Output to engage the Clutch during Remote start. (+) V, Black, pin [3] (+) STSW: pin Clutch Bypass: Lt. Green: pin ONLY for Manual Transmission vehicles [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. [] The siren is only available with the Directed Digital System remote start and security system. [3] STSW: Starter Switch Wire. Refer to the wiring reference chart on page 9 for wire color and connections. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). Black Connector Clutch White Connector Main body ECU 0

11 Type b - with T-Harness THTLC (Push-to-Start Vehicles with CAN) Refer to "Vehicle wiring reference charts" starting on page 7 for more information on vehicle-specific connections. White Connector Headlight Switch Connection required only if Pit-Stop/Idle mode is desired (see details on the page 7). (connector side view) Black ENGINE START STOP Connector Diagnostic Connector at OBDII (-) Parking Lights: pin (+) Clutch: Lt. Green, pin ONLY for Manual Transmission vehicles Black Conn. Clutch (+) V (-) Push-To-Start: pin 7 White Conn. Main body ECU 87 87a ONLY for Manual Transmission vehicles Clutch circuit must be activated for vehicles with manual transmission. Use a relay and one of the available output (pin 7, 9 or 5) programmed for Starter Output via the XpressVIP web tool (-) Starter Output Siren Hood Pin [3] (+) STSW : pin 4 or 6 (-) Push-to-Start Output: Lt. Green/Black (-) Parking Lights Output: Lt. Green/White (+) Starter Switch Wire: Yellow 6-pin Black Connector [] (-) Hood Input: Gray: 3 (-) Starter Output [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White Wh Manual/Auto. Transmission Type Prog. Button 6 Green Bk 4 White 4 Red White -pin Black Connector -pin White Connector Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. THTLC Rev. (optional T-Harness) [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. [] The siren is only available with the Directed Digital System remote start and security system. [3] STSW: Starter Switch Wire. Refer to the wiring reference chart on page 9 for wire color and connections. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

12 Type 3a -Without T-Harness THTLC (Push-to-Start Vehicles with CAN) Refer to "Vehicle wiring reference charts" starting on page 7 for more information on vehicle-specific connections. Diagnostic Connector at OBDII White Connector Headlight Switch HS CAN High: pin 6 HS CAN Low: pin HS CAN Low: Tan: 4 Manual/Auto. Transmission Type Prog. Button White connector at Fuse Box (+) V, Black, pin (-) Push-To-Start: pin 7 Black connector (-)Parking Lights: Black, pin 8 ENGINE START STOP Connection required only if Pit-Stop/Idle mode is desired (see details on the page 7). (connector side view) 8 Hood Pin Siren HS CAN High: Tan/Black: 5 (-) Parking Lights Output: Green/Black: 0 (-) Push-to-Start Output: Lt. Blue/Black: 3 [] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White Wh 6 Green Bk 4 White 4 Red White : Brown: (+) V 0: Red: (+) V 9: Black: (-) Ground Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 6: Yellow: (+) Starter SW Output [3] (+) STSW: pin 4 or [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. [] The siren is only available with the Directed Digital Systems remote start and security system. [3] STSW: Starter Switch Wire. Refer to the wiring reference chart on page 9 for wire color and connections. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). White Connector Main body ECU

13 Type 3b - with T-Harness THTLC (Push-to-Start Vehicles with CAN) Refer to "Vehicle wiring reference charts" starting on page 7 for more information on vehicle-specific connections. White Connector Headlight Switch Connection required only if Pit-Stop/Idle mode is desired (see details on the page 7). (connector side view) Diagnostic Connector at OBDII (-)Parking Lights: Black, pin Black ENGINE START STOP Connector (-) Push-To-Start: pin 7 (-) Push-to-Start Output: Lt. Green/Black (-) Parking Lights Output: Lt. Green/White (+) Starter Switch Wire: Yellow 9 6 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. White Connector Main body ECU Manual/Auto. Transmission Type Prog. Button [3] (+) STSW: pin 4 or 6 Siren Hood Pin 6-pin Black Connector [] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White Wh 6 Green Bk 4 White 4 Red White -pin Black Connector -pin White Connector THTLC Rev. (optional T-Harness) [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. [] The siren is only available with the Directed Digital System remote start and security system. [3] STSW: Starter Switch Wire. Refer to the wiring reference chart on page 0 for wire color and connections. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 3

14 Type 4 (Key-Type Vehicles without CAN) Refer to "Vehicle wiring reference charts" starting on page 7 for more information on vehicle-specific connections. White Connector Headlight Switch Black Connector Immobilizer (+) Starter Output (to starter): Violet [] Starter Input (from key switch): Green (+) V Input: Red (+) Accessory Output: Orange (+) V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) Fused (30A) Ignition / Flex Relay Input: Red/White (+) Ignition /Flex Relay Output: Pink/White Ignition Connector Autolight: pin 9 Refer to the Vehicle Wiring Reference Information for wire and connector details. 8 thick-gauge wires (-) Parking Lights: pin 8 MC50 Start (some vehicles require nd start) 4 White 7 White DATA TX: pin 5 Refer to for clutch wire colors, pin numbers and connector details. DATA RX: pin 4 DATA TX: Yellow/Black: DATA RX: Orange/Black: 3 (-) Parking Lights Output: Green/Black: 0 Diagnostic Connector at OBDII (-) E-Brake Input: Black/White: [] (-) Hood Input: Gray: 3 Tach Input: Violet/White: 6 (-) Unlock Output: Dk. Blue: 7 (-) Trunk Output: Red/White: 9 (-) Door Trigger Input: White/Green: 0 (-) Lock Output: Dk. Green: 5 (+) Brake Input: Brown/White: 6 [3] (+) Siren Output: Brown: 7 (-) Keysense Output: Blue/White: 8 [] The Green wire is only required for starter kill and antigrind connections. [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. [3] The siren is only available with the Directed Digital System remote start and security system. [4] Reprogramming the default feature to starter is required for the clutch bypass. Siren 9 Tach: pin 9 (+) Clutch With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise) Black 3 Wh 7 White 8 White Wh Manual/Auto. Transmission Type Prog. Button 6 Green Bk 4 White 4 Red White 0: Red: (+) V 9: Black: (-) Ground Manual Transmission: Connect to vehicle s clutch. OR Automatic Transmission: Connect to vehicle s starter. Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 5: Orange/Red: Autolight Off 4: Yellow/Red: Autolight Off 8: White/Brown: (+) Clutch Bypass Input [4] (+) V 7: White: (+) Clutch Bypass / Starter Output [4] 4

15 Type 5 (Push-to-Start Vehicles without CAN) Refer to "Vehicle wiring reference charts" starting on page 7 for more information on vehicle-specific connections. Black ENGINE START STOP Connector (-) Push-To-Start: DATA RX: pin 7 pin 0 DATA TX: pin 9 Manual/Auto. Transmission Type Prog. Button DATA TX: Yellow/Black: Diagnostic Connector at OBDII Tach: pin Brake Switch DATA RX: Orange/Black: 3 (-) Parking Lights Output: Green/Black: 0 (-) Push-to-Start Output: Lt. Blue/Black: 3 (+) Ignition Input: Yellow: [] (-) Hood Input: Gray: 3 Tach: Violet/White: 6 (-) Unlock Output: Dk. Blue: 7 (-) Trunk Input: Red/White: 9 (-) Door Trigger Input: White/Green: 0 (-) Lock Output: Dk.Green: 5 (+) Brake Input: Brown/White: 6 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White Wh 6 Green Bk 4 White 4 Red White : Brown: (+) V : Orange/Yellow: Brake 0: Red: (+) V 9: Black: (-) Ground 6: Yellow: Brake Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (+) V 4 (+) Ignition: pin 3 3 (+) Brake: pin Refer to for wire and connector details. Siren [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. [] The siren is only available with the Directed Digital Systems remote start and security system. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 5

16 Type 6 (Push-to-Start Vehicles with Keyport without CAN) Refer to "Vehicle wiring reference charts" starting on page 7 for more information on vehicle-specific connections. (+) V ENGINE START STOP Refer to for wire and connector details a 30 (-) Push-To-Start: pin 7 Black Connector Black Connector Immobilizer DATA TX: pin 5 Diagnostic Connector at OBDII 9 Tach: pin 9 (-) Key Sense Blue,pin 3 6 Key Release: Pink,pin 5 8 Siren Black 5-pin Connector at keyport DATA RX: pin 4 DATA TX: Yellow/Black: DATA RX: Orange/Black: 3 (-) Parking Lights Output: Green/Black: 0 (-) Push-To-Start Output: Lt. Blue/Black: 3 (+) Ignition Input: Yellow: [] (-) Hood Input: Gray: 3 Tach: Violet/White: 6 (-) Unlock Output: Dk. Blue: 7 (-) Trunk Output: Red/White: 9 (-) Door Trigger Input: White/Green: 0 (-) Lock Output: Dk.GReen: 5 (+) Brake Input: Brown/White: 6 [] (+) Siren Output: Brown: 7 (-) GWR Status: Blue/White: 8 6 Black 3 Wh 7 White 8 White Wh Manual/Auto. Transmission Type Prog. Button 6 Green Bk 4 White 4 Red White : Brown: (+) V 0: Red: (+) V 9: Black: (-) Ground 6: Yellow: Brake Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. : Orange/Yellow: Brake Brake Switch 4 (+) Ignition: pin 3 (+) V 3 (+)Brake: pin [] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. [] The siren is only available with the Directed Digital System remote start and security system. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 6

17 Vehicle wiring reference charts This section provides information on the following connections: "Installation Type " "Installation Type " "Installation Type 3" "Installation Type 4" "Installation Type 5" "Installation Type 6" Refer to for more information on additional connections. Pit Stop/ Idle Mode The Pit Stop/Idle feature allows the vehicle to remain running after leaving the vehicle. Refer to the owner's guide of your remote starter for more details. Installation Type Vehicle Wire function Connector Pin position Wire color CAN High Diagnostic Connector 6 Light Green CAN Low Diagnostic Connector 4 White Pontiac Vibe Autolight Not equipped (Key) Parking Lights Headlight Switch 8 Brown RX Immobilizer 4 Light Blue TX Immobilizer 5 Beige CAN High Diagnostic Connector 6 Light Green CAN Low Diagnostic Connector 4 White Scion xb Autolight Not equipped (Key) Parking Lights Headlight Switch 8 Brown RX Immobilizer 4 Light Blue TX Immobilizer 5 Beige CAN High Diagnostic Connector 6 Violet CAN Low Diagnostic Connector 4 White Scion xd Autolight Not equipped (Key) Parking Lights Headlight Switch 3 White RX Immobilizer 4 Green TX Immobilizer 5 Violet CAN High Diagnostic Connector 6 Black CAN Low Diagnostic Connector 4 White Toyota Camry Autolight Headlight Switch 9 Green (Key) Parking Lights Headlight Switch 8 Black RX Immobilizer 4 Brown TX Immobilizer 5 Red 7

18 Vehicle Wire function Connector Pin position Wire color CAN High Diagnostic Connector 6 Light Green CAN Low Diagnostic Connector 4 White Toyota Corolla Autolight Not equipped (Key) Parking Lights Headlight Switch 8 Brown or White RX Immobilizer 4 Light blue or Pink TX Immobilizer 5 Beige or Green CAN High Diagnostic Connector 6 Blue CAN Low Diagnostic Connector 4 White Toyota Highlander Autolight Headlight Switch 9 Green (Key) Parking Lights Headlight Switch 8 Light Blue RX Immobilizer 4 Red TX Immobilizer 5 Light blue CAN High Diagnostic Connector 6 Light Green CAN Low Diagnostic Connector 4 White Toyota Matrix Autolight Not equipped (Key) Parking Lights Headlight Switch 8 Brown RX Immobilizer 4 Light blue TX Immobilizer 5 Beige CAN High Diagnostic Connector 6 Black CAN Low Diagnostic Connector 4 White Toyota RAV4 Autolight Headlight Switch 9 Green (Key) Parking Lights Headlight Switch 8 White RX Immobilizer 4 Pink TX Immobilizer 5 Green Locating Key Components in the vehicle Headlight switch Immobilizer 8

19 Installation Type Vehicle Wire function Connector Pin position Wire color CAN High Diagnostic Connector 6 Light Green Toyota Corolla (Smart Key) Toyota RAV4 (Smart Key) CAN Low Diagnostic Connector 4 White Autolight Not equipped Parking Lights Headlight Switch 8 Brown or White Push-to-Start PTS button 7 White STSW Main Body ECU (E5) 4 Black or White V Fuse Box (G) White CAN High Diagnostic Connector 6 Black CAN Low Diagnostic Connector 4 White Autolight Headlight Switch 9 Green Parking Lights Headlight Switch 8 White Push-to-Start PTS button 7 White STSW Main Body ECU (E7) 4 Red V Fuse Box (G) White Locating Key Components in the vehicle Main Body ECU Push-To-Start Button Headlight switch Installation Type 3 Vehicle Wire function Connector Pin position Wire color CAN High Diagnostic Connector 6 Light Green CAN Low Diagnostic Connector 4 Pink Lexus ES 350 Autolight Headlight Switch 9 Yellow (Smart Key) Parking Lights Headlight Switch 8 Black Push-to-Start PTS button 7 Blue STSW Main Body ECU (E58) 4 or 6 Red or Violet V Fuse Box (DA) White 9

20 Vehicle Wire function Connector Pin position Wire color CAN High Diagnostic Connector 6 Black CAN Low Diagnostic Connector 4 White Toyota Camry Autolight Headlight Switch 9 Green (Smart Key) Parking Lights Headlight Switch 8 Black Push-to-Start PTS button 7 Blue STSW Main Body ECU (E9) 4 or 6 Gray or Violet V Fuse Box (A) Black CAN High Diagnostic Connector 6 Black CAN Low Diagnostic Connector 4 White Toyota Camry Hybrid Autolight Headlight Switch 9 Green (Smart Key) Parking Lights Headlight Switch 8 Black Push-to-Start PTS button 7 Blue STSW Main Body ECU (E9) 4 Gray V Fuse Box (A) Black CAN High Diagnostic Connector 6 Black CAN Low Diagnostic Connector 4 White Autolight Headlight Switch 9 Green Toyota Highlander Parking Lights Headlight Switch 8 Light Blue (Smart Key) Push-to-Start PTS button 7 Pink STSW Main Body ECU (D0) 4 Pink V Fuse Box (A) Black CAN High Diagnostic Connector 6 Black CAN Low Diagnostic Connector 4 White Autolight Headlight Switch 9 Green Toyota Highlander Parking Lights Headlight Switch 8 Light Blue Hybrid (Smart Key) Push-to-Start PTS button 7 Pink STSW Main Body ECU (D0) 4 Yellow V Fuse Box (A) Black Locating Key Components in the vehicle Main Body ECU Push-To-Start Button Headlight switch 0

21 Installation Type 4 Vehicle Wire function Connector Pin position Wire color Autolight Headlight Switch White Lexus ES 330(Key) RX Immobilizer 4 Green/White TX Immobilizer 5 Blue/Yellow Autolight Headlight Switch Green/Orange Lexus GX 470 (Key) RX Immobilizer 4 Yellow TX Immobilizer 5 Yellow/Black Autolight Not Equipped Lexus LS 430 (Key) RX Immobilizer 4 Red/White TX Immobilizer 5 Blue/Black Autolight Headlight Switch Green/Orange Lexus LX 470 (Key) RX Immobilizer 4 Blue/Black TX Immobilizer 5 Violet/Green Autolight Headlight Switch Brown Lexus RX 330 (Key) RX Immobilizer 4 Light Green TX Immobilizer 5 Brown Autolight Headlight Switch 9 Brown Lexus RX 350 (Key) RX Immobilizer 4 Light Green TX Immobilizer 5 Brown Autolight Headlight Switch 9 Brown Lexus RX 400h (Key) RX Immobilizer 4 Green TX Immobilizer 5 Violet Autolight Not Equipped Pontiac Vibe (Key) Clutch Clutch Switch Black 008 RX Immobilizer 4 Blue TX Immobilizer 5 Green Autolight Not Equipped Yellow (in) Scion tc (Key) Clutch Clutch Switch Black (out) RX Immobilizer 4 Yellow TX Immobilizer 5 Red Autolight Headlight Switch Green/Orange Toyota 4Runner (Key) RX Immobilizer 4 Pink/Green TX Immobilizer 5 Light Green/Yellow Autolight Headlight Switch 9 Orange Toyota Avalon (Key) RX Immobilizer 4 Lt.Green TX Immobilizer 5 Brown Autolight Headlight Switch White Toyota Camry (Key) RX Immobilizer 4 Green/White TX Immobilizer 5 Blue/Yellow Autolight Not Equipped Toyota Corolla (Key) Clutch Clutch Switch Black RX Immobilizer 4 Blue TX Immobilizer 5 Green

22 Vehicle Wire function Connector Pin position Wire color Autolight Not Equipped Toyota FJ Cruiser (Key) Clutch Clutch Switch Black/Yellow RX Immobilizer 4 Pink/Green TX Immobilizer 5 Light Green/Red Autolight Headlight Switch Pink Toyota Highlander (Key) RX Immobilizer 4 Gray TX Immobilizer 5 White Autolight Headlight Switch Green/Orange Toyota Land Cruiser (Key) RX Immobilizer 4 Blue/Black TX Immobilizer 5 Violet/Green Autolight Not Equipped Toyota Matrix (Key) Clutch Clutch Switch Black RX Immobilizer 4 Blue TX Immobilizer 5 Green Autolight Not Equipped Toyota RAV4 (Key) RX Immobilizer 4 Blue/Red TX Immobilizer 5 Pink Autolight Headlight Switch 9 White Toyota Sequoia (key) RX Immobilizer 4 Blue/Red TX Immobilizer 5 Pink Autolight Headlight Switch 9 Green Clutch Clutch Switch Black/White Toyota Solara (Key) RX Immobilizer 4 Yellow or Green/White TX Immobilizer 5 Yellow/Red or Blue/Yellow Autolight Not Equipped Toyota Sienna (Key) RX Immobilizer 4 Yellow TX Immobilizer 5 Yellow/Red Toyota Tacoma (Key) Toyota Tundra (Key) Autolight Not Equipped Parking Lights Headlight Switch 8 Green Clutch Clutch Switch Black/Yellow RX Immobilizer 4 Pink/Green TX Immobilizer 5 Lt. Green/Red Autolight Headlight Switch 9 Green Parking Lights Headlight Switch 8 Orange or Beige RX Immobilizer 4 Light Green TX Immobilizer 5 Blue

23 Vehicle Wire function Connector Pin position Wire color Autolight Headlight Switch 9 Brown Toyota Venza (Key) 009 RX Immobilizer 4 Green TX Immobilizer 5 Violet Autolight Not Equipped Toyota Yaris (Key) Clutch Clutch Switch Black RX Immobilizer 4 Green TX Immobilizer 5 Violet Locating Key Components in the vehicle Headlight switch Immobilizer Installation Type 5 Vehicle Wire function Connector Pin position Wire color Push-to-Start PTS button 7 Pink Lexus GS 300 (Smart Key) RX PTS button 0 Yellow 006 TX PTS button 9 Blue Brake Brake Switch Red/Black Push-to-Start PTS button 7 Pink Lexus GS 350 (Smart Key) RX PTS button 0 Yellow TX PTS button 9 Blue Brake Brake Switch Red/Black Push-to-Start PTS button 7 Pink Lexus GS 430 (Smart Key) RX PTS button 0 Yellow TX PTS button 9 Blue Brake Brake Switch Red/Black Push-to-Start PTS button 7 Pink Lexus GS 450h (Smart Key) RX PTS button 0 Yellow TX PTS button 9 Blue Brake Brake Switch Red/Black Push-to-Start PTS button 7 Pink Lexus GS 460 (Smart Key) RX PTS button 0 Yellow 008 TX PTS button 9 Blue Brake Brake Switch Red/Black 3

24 Vehicle Wire function Connector Pin position Wire color Push-to-Start PTS button 7 Black Lexus IS 50 (Smart Key) RX PTS button 0 Light Blue TX PTS button 9 Blue Brake Brake Switch Red/Black Push-to-Start PTS button 7 Black Lexus IS 350 (Smart Key) RX PTS button 0 Light Blue TX PTS button 9 Blue Brake Brake Switch Red/Black Push-to-Start PTS button 7 Black Lexus IS F (Smart Key) RX PTS button 0 Light Blue 008 TX PTS button 9 Blue Brake Brake Switch Red/Black Push-to-Start PTS button 7 White Lexus LS 460 (Smart Key) RX PTS button 0 White TX PTS button 9 Orange Brake Brake Switch Blue Push-to-Start PTS button 7 White Lexus LS 600h (Smart Key) RX PTS button 0 White 008 TX PTS button 9 Orange Brake Brake Switch Blue Push-to-Start PTS button 7 Blue Toyota Avalon RX PTS button 0 White (Smart Key) TX PTS button 9 Gray Brake Brake Switch White Toyota Land Cruiser (Smart Key) Push-to-Start PTS button 7 Black RX PTS button 0 Green TX PTS button 9 Lt. Green Brake Brake Switch Red Locating Key Components in the vehicle Push-To-Start Button Brake switch 4

25 Installation Type 6 Vehicle Wire function Connector Pin position Wire color Push-to-Start PTS button 7 Yellow Prius RX Black 7-pin at keyport 4 Blue TX Black 7-pin at keyport 5 Light Green Brake Brake Switch Blue Locating Key Components in the vehicle Push-To-Start Button Brake switch 5

26 Connecting the module Important! Before connecting the Directed Digital System, it is important to ensure that the proper feature and function programming is selected using the configuration wizard. Visit to use the latest version of the online tool. Flashing a module using your computer:. Disconnect the main module from any (+) V power source, then connect it to your computer using the XKLoader.. Go to using Internet Explorer; the configuration wizard will be displayed automatically. 3. Follow the instructions in the pop up window that will be displayed when the module is detected. Flashing a module using your smartphone or tablet:. Disconnect the main module from any (+) V power source, then connect it to the XKLoader3.. Launch the Directechs Mobile app on your smartphone or tablet. 3. Select FLASH YOUR MODULE and follow the on-screen instructions. When the flashing operation is successful, you can proceed with the instructions below. Manual or automatic transmission selection The yellow loop on the Directed Digital System controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected. Uncut (default): Manual transmission. Cut: Automatic transmission. For safety reasons, all Directed Digital Systems are shipped ready to use with a manual transmission (the yellow loop is untouched). If the loop is cut after power has been applied, it is necessary to cycle power to the main module (via the white -pin main power harness) so the unit will see the state change on the loop and appropriately configure the transmission type. Ready mode To successfully remote start a vehicle equipped with a manual transmission, the Ready Mode feature must be enabled before exiting the vehicle. Please refer to the Owner s Guide for more details on this required process. Additional connections required for vehicles equipped with a manual transmission (if not supported by firmware) Connection (-) Emergency Brake Input (black/white, pin ) (-) Door Input (white/green, pin 0) OR (+) Door Input (yellow/green, pin ) (AC) Tachometer Input (violet/white, pin 6) Description Must be connected to a working emergency brake in the vehicle. Although most vehicles have simple (-) trigger emergency brake circuits note some vehicles do not and may require unique integration methodologies. Must be connected to a working door trigger in the vehicle, which monitors all doors. The unit must monitor the door pins to allow the Ready Mode process to be enabled. Note: Some vehicles may require unique integration methodologies for this circuit. Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.) and learned successfully to the Directed Digital System. Note: Refer to for more information. 6

27 Optional sensors Note: The sensor port is only active on hybrid systems. The 4-pin sensor port is compatible with a number of different Directed sensors including, but not limited to: Shock Sensor 504D Field Disturbance Sensor 508D Ultrasonic Sensor 509U Note: In the case of 508D, power and ground must be hardwired to the vehicle power and ground should NOT be obtained from the 4-pin sensor port. Each sensor will have its own instructions, which must be followed for installation and adjustment. RF kits An RF kit consists of one or multiple remotes, a Control Center (antenna), and an antenna cable various combinations exist. An RF kit allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow the instructions included with the kit for appropriate installation and programming information. When flashing the Directed Digital System, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination. When used in conjunction with SmartStart The Directed Digital System main module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage main module. To ensure that the DD communication between the Directed Digital System and SmartStart works properly, one of the following actions must be executed, depending on the hardware you are using: Rev A SmartStart The brown or blue loop must be cut. Rev B SmartStart The gray wire must be connected to a ground source. Do NOT connect the SmartStart -pin power harness. Power and ground will be provided by the DD connector on main module. 7

28 Module programming Refer to "LED diagnostics and troubleshooting" starting on page 3 for more information and for troubleshooting purposes. Installation Type : Key-Type Vehicles with CAN To connect the module: Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. Connect all the harnesses to the Directed Digital System, EXCEPT the white-pin main power harness. Connect all but the white -pin harness 3 Connect the white-pin main power harness, and wait until the LED turns ON solid red. Must be connected LAST Solid 4 Insert the key in the ignition switch. The LED flashes red slowly for a few seconds to indicate the key is in learning mode AND the LED will then turn ON solid green.* *If the LED starts to flash orange, it indicates the vehicle is equipped with a factory remote starter. Refer to "LED diagnostics and troubleshooting" starting on page 3 for more information. Key IN OFF ON START Flashes Red slowly Solid Green 5 Turn the ignition to ON position. After 3 seconds, the LED shuts OFF. Key IN OFF ON START Solid Green x3 sec. Off 6 Turn vehicle ignition OFF once the module is successfully programmed. Key OUT OFF ON START 7 8 Pair remotes (if applicable). For information on how to pair a specific remote, please refer to its corresponding owner documentation, which can be found inside the product packaging of the complete system or on By default, the tachometer is preprogrammed for the vehicle. For instructions on how to program tach, refer to the Analog Installation Guide, which can be found on Pair remotes* Initialize tachometer * Your aftermarket remote may differ from the model shown in the illustrations. 8

29 Installation Types 3: Push-to-Start (PTS) Vehicles with CAN To connect the module: Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. Connect all the harnesses to the Directed Digital System, EXCEPT the white-pin main power harness. Connect all but the white -pin harness 3 Connect the white-pin main power harness, and wait until the LED turns ON solid red. Must be connected LAST Solid 4 Make sure the key is inside the vehicle. Press the Push-to-Start (PTS) button twice to turn the ignition ON. The LED flashes red slowly for a few seconds to indicate the key is in learning mode AND the LED will then turn ON solid green for 3 seconds then shut off.* *If the LED starts to flash orange, it indicates the vehicle is equipped with a factory remote starter. Refer to "LED diagnostics and troubleshooting" starting on page 3 for more information. X PUSH Flashes Red slowly Solid Green x3 sec. Off 5 Turn vehicle ignition OFF once the module is successfully programmed. X PUSH Off 6 7 Pair remotes (if applicable). For information on how to pair a specific remote, please refer to its corresponding owner documentation, which can be found inside the product packaging of the complete system or on By default, the tachometer is preprogrammed for the vehicle. For instructions on how to program tach, refer to the Analog Installation Guide, which can be found on Pair remotes* Initialize tachometer * Your aftermarket remote may differ from the model shown in the illustrations. 9

30 Installation Type 4: Key-Type Vehicles without CAN To connect the module: Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. Connect all the harnesses to the Directed Digital System, EXCEPT the white-pin main power harness. Connect all but the white -pin harness 3 Connect the white-pin main power harness, and wait until the LED turns ON solid red. Must be connected LAST Solid 4 Insert the key in the ignition switch. The LED flashes red slowly for few seconds to indicate the key is in learning mode. Wait until the LED turns ON solid green. Key IN OFF ON START Flashes Red slowly Solid Green 5 Press the IPB 5 times to skip the CAN programming.the LED turns off quickly then the green LED will turn on for 3 seconds. Press 5x Off Solid Green x3 sec. 6 Remove the key from the ignition once the module is successfully programmed. Key OUT OFF ON START Key IN OFF ON START K 7 8 Pair remotes (if applicable). For information on how to pair a specific remote, please refer to its corresponding owner documentation, which can be found inside the product packaging of the complete system or on By default, the tachometer is preprogrammed for the vehicle. For instructions on how to program tach, refer to the Analog Installation Guide, which can be found on Pair remotes* Initialize tachometer * Your aftermarket remote may differ from the model shown in the illustrations. 30

31 Installation Types 5 6: Push-to-Start (PTS) Vehicles without CAN To connect the module: Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. Connect all the harnesses to the Directed Digital System, EXCEPT the white-pin main power harness. Connect all but the white -pin harness 3 Connect the white-pin main power harness, and wait until the LED turns ON solid red. Must be connected LAST Solid 4 Open the OEM key fob and remove the battery, then place the OEM key fob in front of the PTS button. For Prius (Smart Key) Insert key fob into keyport. HOLD Remove Battery 5 Press the Push-to-Start (PTS) button twice to turn the ignition ON. The LED flashes red slowly for a few seconds to indicate the key is in learning mode and the LED will then turn ON solid green for 3 seconds then shut off. If the LED starts to flash orange, it indicates the vehicle is equipped with a factory remote starter. Refer to "LED diagnostics and troubleshooting" starting on page 3 for more information. X X PUSH PUSH Flashes Red slowly Solid Green x3 sec. Off 6 Press the IPB 5 times to skip the CAN programming. The LED turns off quickly then the green LED will turn on for 3 seconds. Press 5x Off Solid Green x3 sec. 7 Turn vehicle ignition OFF once the module is successfully programmed. X PUSH Off Pair remotes (if applicable). For information on how to pair a specific remote, please refer to its 8 corresponding owner documentation, which can be found inside the product packaging of the complete system or on By default, the tachometer is preprogrammed for the vehicle. For instructions on how to program tach, refer 9 to the Analog Installation Guide, which can be found on * Your aftermarket remote may differ from the model shown in the illustrations. PUSHPair remotes* 3 X Initialize tachometer

Directed Digital System

Directed Digital System Directed Digital System HYUNDAI2 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

INSTALLATION GUIDE. Directed Digital Solutions TL11. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL11. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL11 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions HONDA4. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions HONDA4. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions HONDA4 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions TL6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL6. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL6 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions TL5. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL5. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL5 Designed by Installers for Installers 07 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

DS4+ INSTALLATION GUIDE TL11. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE TL11. Designed by Installers for Installers INSTALLATION GUIDE DS4+ TL11 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by

More information

DS4+ INSTALLATION GUIDE TL10. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE TL10. Designed by Installers for Installers INSTALLATION GUIDE DS+ TL0 Designed by Installers for Installers 0 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person

More information

INSTALLATION GUIDE. Directed Digital Solutions HKHT1. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions HKHT1. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions HKHT1 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions TL1. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL1. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL Designed by Installers for Installers 207 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

Directed Digital System

Directed Digital System Directed Digital System MIT4 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

INSTALLATION GUIDE. Directed Digital Solutions GM11. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions GM11. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions GM Designed by Installers for Installers 208 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions TL3. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL3. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL3 Designed by Installers for Installers 206 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions FORD6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions FORD6. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions FORD6 Designed by Installers for Installers 208 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions FORD4. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions FORD4. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions FORD Designed by Installers for Installers 0 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions MIT2. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions MIT2. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions MIT2 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions GM5. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions GM5. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions GM5 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions FORD12. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions FORD12. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions FORD12 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions HK7. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions HK7. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions HK7 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions MIT6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions MIT6. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions MIT6 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions NISS3HT. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions NISS3HT. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions NISS3HT Designed by Installers for Installers 208 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions FORD6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions FORD6. Designed by Installers for Installers INSTALLATI GUIDE Directed Digital Solutions FORD6 Designed by Installers for Installers 2016 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

Directed Digital System

Directed Digital System Directed Digital System AUDI02 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

Installation Guide. Index. Vehicle Canbus Integration System

Installation Guide. Index. Vehicle Canbus Integration System Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Index

More information

The TL1 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific TOYOTA and LEXUS vehicles.

The TL1 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific TOYOTA and LEXUS vehicles. Platform: DBALL Firmware: TL Rev.: 005 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER13. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER13. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER13 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE. Directed Digital Solutions NISS2HT. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions NISS2HT. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions NISS2HT Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

Automotive Data Solutions Inc.

Automotive Data Solutions Inc. Automotive Data Solutions Inc. INSTALL GUIDE BLADE-AL(TB)-TL TL Available for : BLADE-AL Rev. Date: November, 009 Doc. No.: ##848## 00906 Version FRançaise disponible en ligne au www.idatalink.com please

More information

Directed Digital System

Directed Digital System Directed Digital System VW02 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER10. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER10. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER10 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE. Directed Digital Solutions GM4. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions GM4. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions GM4 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

The TL4 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Toyota and Lexus vehicles.

The TL4 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Toyota and Lexus vehicles. Rev.: 0700 Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation

More information

INSTALLATION GUIDE Toyota Corolla (H Key) TL Designed by Installers for Installers

INSTALLATION GUIDE Toyota Corolla (H Key) TL Designed by Installers for Installers INSTALLATION GUIDE DB3 2017 Toyota Corolla (H Key) - 403.TL10 2.18 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only!

More information

INSTALLATION GUIDE. Directed Digital Solutions GM2. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions GM2. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions GM2 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER7. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER7. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER7 Designed by Installers for Installers 2016 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE Toyota Camry (Smart Key). 933.TL Designed by Installers for Installers

INSTALLATION GUIDE Toyota Camry (Smart Key). 933.TL Designed by Installers for Installers INSTALLATION GUIDE DS4+ 2010 Toyota Camry (Smart Key). 933.TL1 5.02.179 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer

More information

INSTALLATION GUIDE. Directed Digital Solutions VW08. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions VW08. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions VW08 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE Toyota Camry (G Key) TL Designed by Installers for Installers

INSTALLATION GUIDE Toyota Camry (G Key) TL Designed by Installers for Installers INSTALLATION GUIDE DB3 2013 Toyota Camry (G Key) - 403.TL5 4.00 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only!

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER12. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER12. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER2 Designed by Installers for Installers 207 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER6. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER6 Designed by Installers for Installers 208 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

The SUBARU1 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Subaru vehicles.

The SUBARU1 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Subaru vehicles. Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The SUBARU

More information

Important! This product is NOT compatible with vehicles equipped with a manual transmission.

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide This

More information

INSTALLATION GUIDE Honda Accord HONDA Designed by Installers for Installers

INSTALLATION GUIDE Honda Accord HONDA Designed by Installers for Installers INSTALLATION GUIDE DB3 2011 Honda Accord - 403.HONDA56 3.22 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

DS4+ INSTALLATION GUIDE VW08. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE VW08. Designed by Installers for Installers INSTALLATION GUIDE DS4+ VW08 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by

More information

Important! This product is NOT compatible with vehicles equipped with a manual transmission.

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The TL

More information

INSTALLATION GUIDE Chevrolet Impala GM Designed by Installers for Installers

INSTALLATION GUIDE Chevrolet Impala GM Designed by Installers for Installers INSTALLATION GUIDE DB3 2001 Chevrolet Impala - 403.GM2 4.04 Designed by Installers for Installers 2016 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

DS4+ INSTALLATION GUIDE GM2. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE GM2. Designed by Installers for Installers INSTALLATION GUIDE DS4+ GM2 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by

More information

DS4+ INSTALLATION GUIDE FORD12. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE FORD12. Designed by Installers for Installers INSTALLATION GUIDE DS4+ FORD12 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product

More information

INSTALLATION GUIDE Chevrolet Silverado GM Designed by Installers for Installers

INSTALLATION GUIDE Chevrolet Silverado GM Designed by Installers for Installers INSTALLATION GUIDE DB3 2010 Chevrolet Silverado 1500. 403.GM11 1.08 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only!

More information

Transponder Bypass. install type SeLeCtiOn NOTE. Scion/Toyota. FeaTUres. data IMMoBILIZer Bypass

Transponder Bypass. install type SeLeCtiOn NOTE. Scion/Toyota. FeaTUres. data IMMoBILIZer Bypass Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(TB)-TL5-EN TL5 Available for : ADS-AL CA Rev. Date: February 7, 05 Doc. No.: ##088## please visit www.idatalink.com for complete product details The

More information

Installation Guide. Index. Vehicle Canbus Integration System

Installation Guide. Index. Vehicle Canbus Integration System Platform: CANMAX00 Rev.: 20003 Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

More information

The HYUNDAI4 firmware for DBALL2 is an all-in-one door lock and override module compatible with. Vehicle Application Guide...

The HYUNDAI4 firmware for DBALL2 is an all-in-one door lock and override module compatible with. Vehicle Application Guide... Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The HYUNDAI4

More information

INSTALLATION GUIDE Acura TL (Smart Key). 933.HONDA Designed by Installers for Installers

INSTALLATION GUIDE Acura TL (Smart Key). 933.HONDA Designed by Installers for Installers INSTALLATION GUIDE DS4+ 202 Acura TL (Smart Key). 933.HONDA56 3.26.85 Designed by Installers for Installers 207 Directed, Vista CA This product is intended for installation by a professional installer

More information

INSTALLATION GUIDE Dodge/Ram CHRYSLER Designed by Installers for Installers

INSTALLATION GUIDE Dodge/Ram CHRYSLER Designed by Installers for Installers INSTALLATION GUIDE DB3 2016 Dodge/Ram 1500-403.CHRYSLER6 2.04 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

Directed Digital System

Directed Digital System Directed Digital System GM0 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

The NISS3HT firmware for DBALL2 is an all-in-one door lock and override module compatible with. Vehicle Application Guide...02

The NISS3HT firmware for DBALL2 is an all-in-one door lock and override module compatible with. Vehicle Application Guide...02 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The NISS3HT

More information

The SUBARU3 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Subaru vehicles.

The SUBARU3 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Subaru vehicles. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The SUBARU3

More information

DS4+ INSTALLATION GUIDE GM9. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE GM9. Designed by Installers for Installers INSTALLATION GUIDE DS4+ GM9 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by

More information

INSTALL GUIDE OEM-AL(RS)-TL7-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-TL7-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 545 REVISION DATE 08098 FIRMWARE OEM-AL(RS)-TL7-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly

More information

Installation Tips for your Remote Start system (for Toyota vehicles) V3.3 revised 1/10/2013

Installation Tips for your Remote Start system (for Toyota vehicles) V3.3 revised 1/10/2013 Installation Tips for your Remote Start system (for Toyota vehicles) V3.3 revised 1/10/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts

More information

INSTALLATION GUIDE Chevrolet Spark GM Designed by Installers for Installers

INSTALLATION GUIDE Chevrolet Spark GM Designed by Installers for Installers INSTALLATION GUIDE DB3 2015 Chevrolet Spark - 403.GM10 4.07 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

DS4+ INSTALLATION GUIDE CHRYSLER12. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE CHRYSLER12. Designed by Installers for Installers INSTALLATION GUIDE DS4+ CHRYSLER2 Designed by Installers for Installers 7 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product

More information

INSTALLATION GUIDE Dodge/Ram Grand Caravan CHRYSLER Designed by Installers for Installers

INSTALLATION GUIDE Dodge/Ram Grand Caravan CHRYSLER Designed by Installers for Installers INSTALLATION GUIDE DB3 2014 Dodge/Ram Grand Caravan - 403.CHRYSLER 7.23 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer

More information

Vehicle Application Guide... Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Type 1... Type 2... Type 3...

Vehicle Application Guide... Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Type 1... Type 2... Type 3... Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

INSTALL GUIDE OEM-AL(RS)-TL1-[ADS-ALCA]-EN

INSTALL GUIDE OEM-AL(RS)-TL1-[ADS-ALCA]-EN INSTALL GUIDE DOCUMENT NUMBER 56703 REVISION DATE 084 FIRMWARE OEM-AL(RS)-TL-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are

More information

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE FT-DC-S DOCUMENT NUMBER REVISION DATE 060809 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that

More information

The GM9 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Buick, Cadillac, Chevrolet and GMC vehicles.

The GM9 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Buick, Cadillac, Chevrolet and GMC vehicles. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The GM9

More information

The FORD3 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Ford and Lincoln vehicles.

The FORD3 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Ford and Lincoln vehicles. Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The firmware

More information

INSTALL GUIDE OEM-AL(RS)-TL2-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-TL2-[FLCAN]-EN INSTALL GUIDE OEM-AL(RS)-TL-[FLCAN]-EN DOCUMENT NUMBER 5364 REVISION DATE 08098 FIRMWARE OEM-AL(RS)-TL-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc.

More information

Vehicle Application Guide... Key2GO...

Vehicle Application Guide... Key2GO... Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

INSTALLATION GUIDE Mazda 6 (Smart Key) MA RSR. Designed by Installers for Installers

INSTALLATION GUIDE Mazda 6 (Smart Key) MA RSR. Designed by Installers for Installers INSTALLATION GUIDE DB3 2009 Mazda 6 (Smart Key) - 403.MA1 4.00 RSR Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only!

More information

DS4+ INSTALLATION GUIDE. Analog Mode (Viper & Automate) Designed by Installers for Installers

DS4+ INSTALLATION GUIDE. Analog Mode (Viper & Automate) Designed by Installers for Installers INSTALLATION GUIDE DS4+ Analog Mode (Viper & Automate) Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE Chevrolet Cruze GM Designed by Installers for Installers

INSTALLATION GUIDE Chevrolet Cruze GM Designed by Installers for Installers INSTALLATION GUIDE DB3 2011 Chevrolet Cruze - 403.GM10 4.12 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

This module can only be flashed and configured using XpressVIP at or using the Directechs

This module can only be flashed and configured using XpressVIP at  or using the Directechs Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The HYUNDAI

More information

Automotive Data Solutions Inc. Rev. Date: March 18, 2013 Doc. No.: ##11179##

Automotive Data Solutions Inc. Rev. Date: March 18, 2013 Doc. No.: ##11179## Automotive Data Solutions Inc. INSTALL GUIDE ADS-TB-TL5-EN TL5 Available for : ADS-TB Rev. Date: March 8, 03 Doc. No.: ##79## Version FRançaise disponible en ligne au www.idatalink.com please visit www.idatalink.com/support

More information

This module can only be flashed and configured using XpressVIP at or using the Directechs

This module can only be flashed and configured using XpressVIP at   or using the Directechs Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The NISS08

More information

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE 206025 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that

More information

ALWAYS TEST THE INSTALLATION ONCE A RELAY IS INSTALLED, TO ENSURE THE VEHICLE CANNOT BE STARTED IN GEAR.

ALWAYS TEST THE INSTALLATION ONCE A RELAY IS INSTALLED, TO ENSURE THE VEHICLE CANNOT BE STARTED IN GEAR. Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The DBALL-NISS2

More information

Door lock and transponder interface compatible with first generation Chrysler, Dodge and Jeep vehicles. Vehicle Application Guide...

Door lock and transponder interface compatible with first generation Chrysler, Dodge and Jeep vehicles. Vehicle Application Guide... Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

The FORD12 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Ford and Lincoln

The FORD12 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Ford and Lincoln Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The FORD12

More information

Door lock and key interface compatible with the latest Kia vehicles. The available features include brake, hood, trunk and door trigger sensors.

Door lock and key interface compatible with the latest Kia vehicles. The available features include brake, hood, trunk and door trigger sensors. Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

Vehicle Application Guide... Installation Type 1... Type 2... Type 3... Wiring Reference Charts...

Vehicle Application Guide... Installation Type 1... Type 2... Type 3... Wiring Reference Charts... Platform: DBALL/DBALL Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation

More information

TL2 INSTALL GUIDE OL-AL(MDB)-TL2-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

TL2 INSTALL GUIDE OL-AL(MDB)-TL2-EN. Alarms & Remote Start. Automotive Data Solutions Inc. Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE OL-AL(MDB)-TL2-EN TL2 AVAILABLE FOR : OL-MDB-ALL Rev. Date: April 08, 2016 Doc. No.: ##28069## U.S. PATENT NO. 8,856,780 The brand names

More information

Programming Module Programming & Reset... Features & Options List... Features Programming... LED Diagnostics & Troubleshooting...

Programming Module Programming & Reset... Features & Options List... Features Programming... LED Diagnostics & Troubleshooting... Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The DBALL/DBALL2-NISS01

More information

Vehicle Application Guide... Key2GO... Installation Wiring Diagram... Optional T-Harness... Wiring Reference Charts...

Vehicle Application Guide... Key2GO... Installation Wiring Diagram... Optional T-Harness... Wiring Reference Charts... Platform: DBALL/DBALL Rev.: 05050 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this

More information

Vehicle Application Guide... Installation (Wiring Diagram & Vehicle Wiring Reference Charts)...

Vehicle Application Guide... Installation (Wiring Diagram & Vehicle Wiring Reference Charts)... Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The GM

More information

INSTALLATION GUIDE Nissan Altima (Smart Key) NISS3HT 3.08 RSR. Designed by Installers for Installers

INSTALLATION GUIDE Nissan Altima (Smart Key) NISS3HT 3.08 RSR. Designed by Installers for Installers INSTALLATION GUIDE DB3 2009 Nissan Altima (Smart Key) - 403.NISS3HT 3.08 RSR Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer

More information

Important! NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide...02

Important! NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide...02 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The NISS3HT

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN DOCUMENT NUMBER 990 REVISION DATE 008 FIRMWARE OEM-AL(RS)-CH0-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) NOTICE

More information

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide...

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide... Platform: DBALL Rev.: 058 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE DOCUMENT NUMBER 80 REVISION DATE 008 FIRMWARE OEM-AL(RS)-VW-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE DOCUMENT NUMBER 809 REVISION DATE 0608 FIRMWARE COL-AL(RS)-VW6-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) OMEGA-CARLINK-GPS (OPTIONAL) NOTICE

More information

Vehicle Application Guide... Key2GO... Installation Without T-Harness... With T-Harness THCHD3...

Vehicle Application Guide... Key2GO... Installation Without T-Harness... With T-Harness THCHD3... Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

Vehicle Application Guide... Key2GO... Installation Without T-Harness... With T-Harness THCHD3... Vehicle Wiring Reference Charts...

Vehicle Application Guide... Key2GO... Installation Without T-Harness... With T-Harness THCHD3... Vehicle Wiring Reference Charts... Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

This firmware does not support transponder override. One factory programmed key is required to install a remote starter.

This firmware does not support transponder override. One factory programmed key is required to install a remote starter. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide This

More information

idatastart HC Document number Revision Date

idatastart HC Document number Revision Date PRODUCT guide idatastart HC Document number Revision Date 05 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that

More information

Important! This product is NOT compatible with vehicles equipped with a manual transmission.

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide This

More information

Vehicle Application Guide...

Vehicle Application Guide... Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE FT-DC-S DOCUMENT NUMBER REVISION DATE 0605 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

Programming Module Programming & Reset... Features & Options List... Features Programming... LED Diagnostics & Troubleshooting...

Programming Module Programming & Reset... Features & Options List... Features Programming... LED Diagnostics & Troubleshooting... Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The DBALL-NISS03

More information

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: June 28, 2018 Doc. No.: ##51678##

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: June 28, 2018 Doc. No.: ##51678## Automotive Data Solutions Inc. INSTALL GUIDE FLC-AL(DL)-HK-EN AVAILABLE FOR : FLCAN Rev. Date: June, 0 Doc. No.: #### HK U.S. PATENT NO.,,0 PLEASE VISIT WWW.FLASHLOGIC.COM FOR COMPLETE PRODUCT DETAILS

More information