INSTALLATION GUIDE. Directed Digital Solutions TL5. Designed by Installers for Installers

Transcription

1 INSTALLATION GUIDE Directed Digital Solutions TL5 Designed by Installers for Installers 07 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and components

2 Contents Warning! Safety first... 3 Introduction... 4 Pre-installation and application warnings... 4 Vehicle application guide... 5 Wiring connections... 6 Main power harness (H), -pin thick gauge connector... 6 Auxiliary output harness (H), 6-pin black connector... 6 Analog harness (H3), 8-pin white connector... 7 MC50 harness (H4), 8 thick-gauge wires (optional)... 7 Installation (wiring diagrams & vehicle wiring reference charts)... 8 Type... 8 Type... 0 Type 3... Type Type Type Type 7... Connecting the module... 3 Important!... 3 Manual or automatic transmission selection... 3 Optional sensors... 4 RF Systems... 4 When used in conjunction with SmartStart... 4 Module programming... 5 LED diagnostics and troubleshooting... 6 Soft reset... 8 Hard reset... 8 Learning the Tach (not needed with Virtual Tach)... 9 Initializing Virtual Tach (not needed with hardwired or data tach applications)... 9 Limited lifetime consumer warranty Quick Reference Guide... 3

3 Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, () Never remotely start the vehicle with the vehicle in gear, and () Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. 3 Directed Digital Solutions TL Directed. All rights reserved.

4 Introduction The TL5 firmware for Directed Digital Solutions is compatible with specific Toyota and Scion vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide provides information on the installation of the module as an analog unit. If you would prefer using this system as a digital solution, go to and search for the make, model and year of the vehicle. This will allow you to find the proper firmware and corresponding installation guide. Warning! This module can only be programmed via the web tool, which can be found on or using the Directechs Mobile application for mobile devices. Features and functions will become accessible when you connect the module using the XKLoader. Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness compatible Keys required for programming Keys required for operation 0 Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector. Refer to the "Vehicle wiring reference chart" following each installation type. A MC50 relay pack is required for this installation. General notes: This section highlights important information for this specific firmware. [] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin. [] The siren is ONLY required when enabling the security features during module flashing. [3] The Green wire is ONLY required for starter disable and antigrind applications. [4] Autolight Interrupt connection required ONLY if the vehicle is equipped with automatic headlights. Additional parts required (maximum required): 87 Diode 6A 0 x A Diodes 87a x Relay esistor 00 0 x Resistor Fuse 7.5A 0 x Fuse 4 Directed Digital Solutions TL Directed. All rights reserved.

5 Vehicle application guide The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock Scion tc xb 7 xd 4 Toyota Avalon (G Key) Corolla (G Key) 3 Highlander (G Key) 3 Matrix (G Key) 3 3 RAV4 (G Key) 3 Sienna (G Key) Tacoma (G Key) 3 Tundra (G Key) 5 Yaris (G Key) 6 Legend: AV: Horn & Light Controls DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DL-Sliding Door Control Driver DL-Sliding Door Control Passenger DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote FOB-DL Interface Sync w/fob remote RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-E-Brake Status ST-Ignition Status Key Types Some Toyota 00+ models have different encryption types. Please look at your key blade and identify the markings. A "G" means Some Toyota the vehicle 00+ is models compatible have different with TL5 encryption firmware. types. Standard Please lookat key or your H key indicates blade and the identify vehicle the markings. is not compatible with this firmware. A G means the vehicle is compatible with TL5 firmware. Standard key or H indicates the vehicle is not compatible with this firmware. Standard Key G-stam ped keys H-stam ped keys For vehicles with Standard key, see TL firmware. TL5 works only with G-stamped keys. For vehicles with H-stamped key, see TL0 firmware. TL5 works only with G -stamped keys. H 5 Directed Digital Solutions TL Directed. All rights reserved.

6 Wiring connections The wiring connections listed below are specific to this firmware. Main power harness (H), -pin thick gauge connector Conn./Pin Color Description H/ White Relay 3 COM (+) Starter Output H/ White/Brown Relay 3 N.O. (+) V Input H/3 Brown/Red Relay N.O. No Connection H/4 Yellow/Red Relay COM Autolights Interrupt (connector side) H/5 Orange/Red Relay N.C. Autolights Interrupt (vehicle side) H/6 Yellow Relay COM Keyless Data H/7 White Relay 3 COM (+) Starter Output H/8 White/Brown Relay 3 N.O. (-) V Input H/9 Black (-) Ground H/0 Red (+) V Input H/ Orange/Yellow Relay N.C. RDA H/ Brown Relay N.O. SIL Auxiliary output harness (H), 6-pin black connector Conn./Pin Color Description H/ Violet/Brown No Connection H/ Yellow/Black Data Output or SIL H/3 Orange/Black CODE H/4 Tan HS CAN Low H/5 Tan/Black HS CAN High H/6 Light Green No Connection H/7 Orange/Green No Connection H/8 Orange/Brown No Connection H/9 Violet/Green No Connection H/0 Green/Black (-) Parking Lights Output H/ White/Violet No Connection H/ White/Red No Connection H/3 Lt. Blue/Black (-) Keysense Output H/4 Green/Red No Connection H/5 N/A No Connection H/6 Violet/Yellow TXCT. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 6 Directed Digital Solutions TL Directed. All rights reserved.

7 Analog harness (H3), 8-pin white connector Conn./Pin Color Description H3/ Lt. Blue/Red (-) Keysense Input H3/ Black/White (-) Parking Brake Input (manual transmission) H3/3 Gray (-) Hood Input H3/4 N/A No Connection H3/5 Gray/Black (+) Glow Plug Input H3/6 Violet/White (AC) Tach Input H3/7 Dark Blue (-) Unlock Output H3/8 Brown/Black (-) Horn H3/9 Red/White (-) Trunk Release Output H3/0 White/Green (-) Door Input H3/ Yellow/Green (+) Door Input H3/ Blue/Red No Connection H3/3 Light Blue (-) Trunk Trigger Input H3/4 Pink/Yellow (-) Activation (start) Input H3/5 Dark Green (-) Lock Output H3/6 Brown/White (+) Brake Input H3/7 Brown (+) Siren Output H3/8 Blue/White (-) Ground When Running (status) Output MC50 harness (H4), 8 thick-gauge wires (optional) Conn./Pin Color Description H4/ Pink/White (+) Ignition /Flex Relay Output 3 H4/ Red/White (+) Fused (30A) Ignition /Flex Relay Input H4/3 Pink (+) Ignition Output (also input to Yellow in ribbon cable) H4/4 Red (+) Volt (battery) Input H4/5 Orange (+) Accessory Output H4/6 Red (+) Volt (battery) Input H4/7 Green Starter Input (from key switch) 4 H4/8 Violet (+) Starter Output (to starter). If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary.. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a list of compatible features. 3. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 4. The Green wire is only required for starter disable and anti-grind applications. 7 Directed Digital Solutions TL Directed. All rights reserved.

8 Installation (wiring diagrams & vehicle wiring reference charts) Type Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). HS CAN High: Pink, pin 6 SIL: Violet, pin 7 8 Black 7-pin conn. (transponder key amplifier at ignition switch) Body ECU Connector Diagnostic Connector OBDII (connector side view) 9 6 HS CAN Low: White, pin 4 TXCT: Gray or Brown, pin CODE: Lt.Green, pin 4 Data Output: Yellow/Black: CODE: Orange/Black: 3 HS CAN Low: Tan: 4 RDA: Lt.Green, pin 6 HS CAN High: Tan/Black: 5 (+) Starter Output (to starter): Violet Starter Input (from key switch): Green (+) V Input: Red (+) Accessory Output: Orange (+) V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) Fused (30A) Ignition / Flex Relay Input: Red/White (+) Ignition /Flex Relay Output: Pink/White 8 thick-gauge wires MC50 4 White 7 White (-) Parking Lights Output: Green/Black: 0 (-) Keysense Output: Lt. Blue/Black: 3 TXCT: Violet/Yellow: 6 (-) Keysense Input: Lt. Blue/Red: Hood Pin (-) Hood Input: Gray: 3 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. : Brown: SIL : Orange/Yellow: RDA 0: Red: (+) V Input 9: Black: (-) Ground 6: Yellow: DATA Input Ignition Connector 5: Orange/Red: Autolights Interrupt (veh. side) (+) Siren Output: Brown: 7 4: Yellow/Red: Autolights Interrupt (conn. side) & 8: White/Brown: (+) V Input 4 3 & 7: White: (+) Starter Output Siren Refer to the Vehicle wiring reference chart Information for wire and connector details. (-) Parking Lights: Blue, pin Keysense: Black, pin CUT White 0-pin conn. (headlight switch) White 4-pin conn. (key switch) Autolights Interrupt: Orange, pin 9 8 Directed Digital Solutions TL Directed. All rights reserved.

9 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Avalon (G Key) 00-0 HS CAN High Pink 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL Violet 7 Data OBDII. White 6 A TXCT Gray or Brown 5 Data Transponder Key Amplifier. Black 7 B CODE Lt.Green 4 Data Transponder Key Amplifier. Black 7 B Parking Lights Blue 8 (-) Headlight switch. White 0 C Autolight Interrupt Orange 9 Cut Headlight switch. White 0 C V Black 7 (+) Ignition switch. White 8 D Accessory Gray 3 (+) Ignition switch. White 8 D Ignition Yellow 6 (+) Ignition switch. White 8 D Ignition Green 4 (+) Ignition switch. White 8 D Starter Blue 8 (+) Ignition switch. White 8 D Starter Red (+) Ignition switch. White 8 D RDA Lt.Green 6 Data Body ECU. White 30 E Keysense Black (-) Key Warning Switch. White 4 F 9 Directed Digital Solutions TL Directed. All rights reserved.

10 Type Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). HS CAN High: Black, pin 6 SIL: Violet or White, pin 7 Black 7-pin conn. (transponder key amplifier at ignition switch) 8 Body ECU Connector Diagnostic Connector OBDII (connector side view) 9 6 HS CAN Low: White, pin 4 TXCT: Red or Yellow/Red, pin CODE: Yellow, pin 4 DATA Output: Yellow/Black: CODE: Orange/Black: RDA: Lt.Green or Pink, pin HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (+) Starter Output (to starter): Violet Starter Input (from key switch): Green (+) V Input: Red (+) Accessory Output: Orange (+) V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) Fused (30A) Ignition / Flex Relay Input: Red/White (+) Ignition /Flex Relay Output: Pink/White 8 thick-gauge wires MC50 4 White 7 White (-) Parking Lights Output: Green/Black: 0 (-) Keysense Output: Lt. Blue/Black: 3 TXCT: Violet/Yellow: 6 (-) Keysense Input: Lt. Blue/Red: Hood Pin (-) Hood Input: Gray: 3 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. : Brown: SIL : Orange/Yellow: RDA 0: Red: (+) V Input 9: Black: (-) Ground 6: Yellow: DATA Input Ignition Connector (+) Siren Output: Brown: 7 5: Orange/Red: Autolights Interrupt (veh. side) 4: Yellow/Red: Autolights Interrupt (conn. side) & 8: White/Brown: (+)V Input 4 3 & 7: White: (+) Starter Output Siren Autolights Interrupt: Violet, pin Refer to the Vehicle wiring reference chart Information for wire and connector details. (-) Keysense: Black or Blue/Black, pin CUT White -pin (Key switch) (-) Parking Lights: Brown or Green/Black, pin White 7-pin conn. (headlight switch) 0 Directed Digital Solutions TL Directed. All rights reserved.

11 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Scion tc 00 HS CAN High Black 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL Violet 7 (-) OBDII. White 6 A TXCT Red 5 Data Transponder Key Amplifier. Black 7 B CODE Yellow 4 Data Transponder Key Amplifier. Black 7 B Parking Lights Brown 4 (-) Headlight switch. White 7 C Autolight Interrupt Not Equipped. V Red 7 (+) Ignition switch. White 8 D Accessory Gray 3 (+) Ignition switch. White 8 D Ignition Blue 6 (+) Ignition switch. White 8 D Ignition Yellow 4 (+) Ignition switch. White 8 D Starter Black 8 (+) Ignition switch. White 8 D Starter Green (+) Ignition switch. White 8 D RDA Lt.Green 6 Data Body ECU. White 30 E Keysense Black (-) Key Warning Switch. White F Toyota Sienna (G Key) 00 HS CAN High Black 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL White 7 Data OBDII. White 6 A TXCT Yellow/Red 5 Data Transponder Key Amplifier. Black 7 B CODE Yellow 4 Data Transponder Key Amplifier. Black 7 B Parking Lights Green/Black 4 (-) Headlight switch. White 7 C Autolight Interrupt Violet Cut Headlight switch. White 7 C V White/Red 5 (+) Ignition switch. White 6 D Accessory Pink 3 (+) Ignition switch. White 6 D Ignition Black 6 (+) Ignition switch. White 6 D Ignition Black/Yellow (+) Ignition switch. White 6 D Starter Black/Yellow 4 (+) Ignition switch. White 6 D Starter Not Equipped. RDA Pink 6 Data Body ECU. White 30 E Keysense Blue/Black (-) Key Warning Switch. White F Directed Digital Solutions TL Directed. All rights reserved.

12 Type 3 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). Diagnostic Connector OBDII (connector side view) HS CAN High: Pin 6 9 SIL: Pin HS CAN Low: Pin 4 Black 7-pin conn. (ignition switch) TXCT: Pin (+) Starter Output (to starter): Violet [] Starter Input (from key switch): Green (+) V Input: Red (+) Accessory Output: Orange (+) V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) Fused (30A) Ignition / Flex Relay Input: Red/White (+) Ignition /Flex Relay Output: Pink/White 8 thick-gauge wires MC50 4 White 7 White SIL: Yellow/Black: CODE: Pin 4 CODE: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (-) Parking Lights Output: Green/Black: 0 (-) Keysense Output: Lt. Blue/Black: 3 TXCT: Violet/Yellow: 6 (-) Keysense Input: Lt. Blue/Red: 0: Red: (+) V Input Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. Ignition Connector Hood Pin (-) Hood Input: Gray: 3 9: Black: (-) Ground 5: Orange/Red: Autolights Interr.(veh. side) Keysense: Pin (+) Siren Output: Brown: 7 4: Yellow/Red: Autolights Interr. (conn. side) & 8: White/Brown: (+) V Input & 7: White: (+) Starter Output Refer to the Vehicle wiring reference chart Information for wire and connector details. White -pin (Key switch) Siren (-) Parking Lights: Pin 8 CUT Autolight Interrupt: Green or Violet, pin White 0-pin conn. (headlight switch) Directed Digital Solutions TL Directed. All rights reserved.

13 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Corolla (G Key) 00 HS CAN High Lt.Green 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL White 7 Data OBDII. White 6 A TXCT Tan or Green 5 Data Transponder Key Amplifier. Black 7 B CODE Lt.Blue or Pink 4 Data Transponder Key Amplifier. Black 7 B Parking Lights Brown or White 8 (-) Headlight switch. White 0 C Autolight Interrupt Not Equipped. V Blue 7 (+) Ignition switch. White 8 D Accessory Gray or Black 3 (+) Ignition switch. White 8 D Ignition Brown or Gray 6 (+) Ignition switch. White 8 D Ignition Green or White 4 (+) Ignition switch. White 8 D Starter Black or White 8 (+) Ignition switch. White 8 D Starter White (if equipped) (+) Ignition switch. White 8 D Keysense Lt. Blue (-) Key Warning Switch. White E Toyota Highlander (G Key) 00 HS CAN High Blue 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL Gray 7 Data OBDII. White 6 A TXCT Lt.Blue 5 Data Transponder Key Amplifier. Black 7 B CODE Red 4 Data Transponder Key Amplifier. Black 7 B Parking Lights Lt.Blue 8 (-) Headlight switch. White 0 C Autolight Interrupt Green 9 Cut Headlight switch. White 0 C V White/Black 5 (+) Ignition switch. White 8 D Accessory Gray (+) Ignition switch. White 8 D Ignition Black 6 (+) Ignition switch. White 8 D Ignition Lt.Blue (+) Ignition switch. White 8 D Starter Yellow 7 (+) Ignition switch. White 8 D Starter Red 3 (+) Ignition switch. White 8 D Keysense Lt.Blue (-) Key Warning Switch. White E 3 Directed Digital Solutions TL Directed. All rights reserved.

14 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Matrix (G Key) 00-0 HS CAN High Lt.Green 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL White 7 Data OBDII. White 6 A TXCT Tan 5 Data Transponder Key Amplifier. Black 7 B CODE Lt.Blue 4 Data Transponder Key Amplifier. Black 7 B Parking Lights Brown 8 (-) Headlight switch. White 0 C Autolight Interrupt Not Equipped. V White 7 (+) Ignition switch. White 8 D Accessory Gray 3 (+) Ignition switch. White 8 D Ignition Brown 6 (+) Ignition switch. White 8 D Ignition Green 4 (+) Ignition switch. White 8 D Starter Black 8 (+) Ignition switch. White 8 D Starter White (.4L models only) (+) Ignition switch. White 8 D Keysense Lt.Blue (-) Key Warning Switch. White E Toyota RAV4 (G Key) 00 HS CAN High Black 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL White 7 Data OBDII. White 6 A TXCT Green 5 Data Transponder Key Amplifier. Black 7 B CODE Pink 4 Data Transponder Key Amplifier. Black 7 B Parking Lights White 8 (-) Headlight switch. White 0 C Autolight Interrupt Green 9 Cut Headlight switch. White 0 C V Blue 7 (+) Ignition switch. White 8 D Accessory Red 3 (+) Ignition switch. White 8 D Ignition White 6 (+) Ignition switch. White 8 D Ignition Pink 4 (+) Ignition switch. White 8 D Starter Yellow 8 (+) Ignition switch. White 8 D Starter White (+) Ignition switch. White 8 D Keysense Blue (-) Key Warning Switch. White E Toyota Tacoma (G Key) 00 HS CAN High Yellow/Black 6 Data OBDII. White 6 A HS CAN Low Blue/White 4 Data OBDII. White 6 A SIL White 7 Data OBDII. White 6 A TXCT Lt.Green/Red 5 Data Transponder Key Amplifier. Black 7 B CODE Pink/Green 4 Data Transponder Key Amplifier. Black 7 B Parking Lights Green 8 (-) Headlight switch. White 0 C Autolight Interrupt Not Equipped. V White/Red 5 (+) Ignition switch. White 8 D Accessory White/Green (+) Ignition switch. White 8 D Ignition Black/Red 6 (+) Ignition switch. White 8 D Ignition Blue/Yellow (+) Ignition switch. White 8 D Starter Green/Black 7 (+) Ignition switch. White 8 D Starter Black/White 3 (+) Ignition switch. White 8 D Keysense Green/Black (-) Key Warning Switch. White E 4 Directed Digital Solutions TL Directed. All rights reserved.

15 Type 4 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). HS CAN High: Violet, pin 6 SIL: Blue, pin 7 White 3-pin conn. (headlight switch) 8 Black 7-pin conn. (ignition switch) Diagnostic Connector OBDII (connector side view) 9 6 HS CAN Low: White, pin (-) Parking Lights: White, pin 3 TXCT: Violet, pin 5 (+) Starter Output (to starter): Violet [] Starter Input (from key switch): Green (+) V Input: Red (+) Accessory Output: Orange (+) V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) Fused (30A) Ignition / Flex Relay Input: Red/White (+) Ignition /Flex Relay Output: Pink/White 8 thick-gauge wires MC50 4 White 7 White Keysense: Yellow, pin Hood Pin CODE: Green, pin 4 SIL: Yellow/Black: CODE: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (-) Parking Lights Output: Green/Black: 0 (-) Keysense Output: Lt. Blue/Black: 3 TXCT: Violet/Yellow: 6 (-) Keysense Input: Lt. Blue/Red: (-) Hood Input: Gray: 3 0: Red: (+) V Input Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. Ignition Connector (-) Unlock Output: Dk. Blue: 7 (-) Lock Output: Dk. Green: White -pin (Key switch) (-) Unlock: Green, pin 8 (-) Lock: Brown, pin 7 (+) Siren Output: Brown: 7 9: Black: (-) Ground Refer to the Vehicle wiring reference chart Information for wire and connector details Siren White 0-pin conn. (driver kick panel) 5 Directed Digital Solutions TL Directed. All rights reserved.

16 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Scion xd 00 HS CAN High Violet 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL Blue 7 Data OBDII. White 6 A TXCT Violet 5 Data Transponder Key Amplifier. Black 7 B CODE Green 4 Data Transponder Key Amplifier. Black 7 B Parking Lights White 3 (-) Headlight switch. White 3 C Autolight Interrupt Not Equipped. V Yellow 4 (+) Ignition switch. White 8 D Accessory White (+) Ignition switch. White 8 D Ignition Pink 6 (+) Ignition switch. White 8 D Ignition Green (+) Ignition switch. White 8 D Starter Black 7 (+) Ignition switch. White 8 D Starter Not Equipped. Keysense Yellow (-) Key Warning Switch White E Lock Brown 7 (-) Driver kick panel. White 0 F Unlock Green 8 (-) Driver kick panel. White 0 F 6 Directed Digital Solutions TL Directed. All rights reserved.

17 Type 5 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). HS CAN High: Violet, pin 6 SIL: Tan, pin 7 8 Black 7-pin conn. (transponder key amplifier at ignition switch) Diagnostic Connector OBDII (connector side view) 9 6 HS CAN Low: White, pin 4 TXCT: Blue, pin CODE: Lt.Green, Pin 4 SIL: Yellow/Black: CODE: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (+) Starter Output (to starter): Violet Starter Input (from key switch): Green (+) V Input: Red (+) Accessory Output: Orange (+) V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) Fused (30A) Ignition / Flex Relay Input: Red/White (+) Ignition /Flex Relay Output: Pink/White 8 thick-gauge wires MC50 4 White 7 White (-) Parking Lights Output: Green/Black: 0 (-) Keysense Output: Lt. Blue/Black: 3 TXCT: Violet/Yellow: 6 (-) Keysense Input: Lt. Blue/Red: Hood Pin (-) Hood Input: Gray: 3 0: Red: (+) V Input 9: Black: (-) Ground Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 5: Orange/Red: Autolights Interrupt (veh. side) 4: Yellow/Red: Autolights Interrupt (conn. side) Ignition Connector (+) Siren Output: Brown: 7 & 8: White/Brown: (+) V Input & 7: White: (+) Starter Output 4 3 Siren Refer to the Vehicle wiring reference chart Information for wire and connector details. White -pin (Key switch) Keysense: Gray, pin CUT Autolights Interrupt: Green, pin 9 (-) Parking Lights: Tan, pin White 0-pin conn. (headlight switch) 7 Directed Digital Solutions TL Directed. All rights reserved.

18 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Tundra (G Key) 00 HS CAN High Violet 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL Tan 7 Data OBDII. White 6 A TXCT Blue 5 Data Transponder Key Amplifier. Black 7 B CODE Lt.Green 4 Data Transponder Key Amplifier. Black 7 B Parking Lights Tan 8 (-) Headlight switch. White 0 C Autolight Interrupt Green 9 Cut Headlight switch. White 0 C V Blue or White 5,4 (+) Ignition switch. White 8 D Accessory Gray (+) Ignition switch. White 8 D Ignition Black 6 (+) Ignition switch. White 8 D Ignition Lt.Green (+) Ignition switch. White 8 D Starter Green 7 (+) Ignition switch. White 8 D Starter Not Equipped. Keysense Gray (-) Key Warning Switch. White E 8 Directed Digital Solutions TL Directed. All rights reserved.

19 Type 6 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). HS CAN High: Violet, pin 6 SIL: Gray, pin 7 Black 7-pin conn. (transponder key amplifier at ignition switch) 8 Diagnostic Connector OBDII (connector side view) 9 6 HS CAN Low: White, pin TXCT: Violet, pin 5 CODE: Green, pin 4 CODE: Orange/Black: 3 SIL: Yellow/Black: HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (+) Starter Output (to starter): Violet Starter Input (from key switch): Green (+) V Input: Red (+) Accessory Output: Orange (+) V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) Fused (30A) Ignition / Flex Relay Input: Red/White (+) Ignition /Flex Relay Output: Pink/White 8 thick-gauge wires MC50 4 White 7 White (-) Parking Lights Output: Green/Black: 0 (-) Keysense Output: Lt. Blue/Black: 3 TXCT: Violet/Yellow: 6 (-) Keysense Input: Lt. Blue/Red: Hood Pin (-) Hood Input: Gray: 3 0: Red: (+) V Input Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. Ignition Connector (+) Siren Output: Brown: Siren 9: Black: (-) Ground Refer to the Vehicle wiring reference chart Information for wire and connector details. (-) Keysense: Yellow, pin White -pin (Key switch) (-) Parking Lights: White, pin White3-pin conn. (headlight switch) 9 Directed Digital Solutions TL Directed. All rights reserved.

20 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Toyota Yaris (G Key) 00 HS CAN High Violet 6 Data OBDII. Black 6 A HS CAN Low White 4 Data OBDII. Black 6 A SIL Gray 7 Data OBDII. Black 6 A TXCT Violet 5 Data Transponder Key Amplifier. Black 7 B CODE Green 4 Data Transponder Key Amplifier. Black 7 B Parking Lights White 3 (-) Headlight switch. White 3 C Autolight Interrupt Not Equipped. V Gray 5 (+) Ignition switch. White 8 D Accessory White (+) Ignition switch. White 8 D Ignition Pink 6 (+) Ignition switch. White 8 D Ignition Green (+) Ignition switch. White 8 D Starter Black 7 (+) Ignition switch. White 8 D Starter Not Equipped. Keysense Yellow (-) Key Warning Switch. White E 0 Directed Digital Solutions TL Directed. All rights reserved.

21 Type 7 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). HS CAN High: Lt.Green, pin 6 Diagnostic Connector OBDII (connector side view) 9 SIL: White, pin HS CAN Low: White, pin 4 Black 7-pin conn. (ignition switch) TXCT: Green, pin 5 CODE: Pink, pin 4 SIL: Yellow/Black: (+) Starter Output (to starter): Violet [] Starter Input (from key switch): Green (+) V Input: Red (+) Accessory Output: Orange (+) V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) Fused (30A) Ignition / Flex Relay Input: Red/White (+) Ignition /Flex Relay Output: Pink/White 8 thick-gauge wires MC50 4 White 7 White CODE: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (-) Parking Lights Output: Green/Black: 0 (-) Keysense Output: Lt. Blue/Black: 3 TXCT: Violet/Yellow: 6 (-) Keysense Input: Lt. Blue/Red: Hood Pin 0: Red: (+) V Input Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (-) Hood Input: Gray: 3 Ignition Connector Keysense: Blue, pin (-) Unlock Output: Dk. Blue: 7 9: Black: (-) Ground Refer to the Vehicle wiring reference chart Information for wire and connector details. White -pin (Key switch) (-) Lock: Lt.Blue, pin 7 Siren (-) Unlock: Pink, pin 6 (-) Lock Output: Dk. Green: 5 (+) Siren Output: Brown: 7 & 8: White/Brown: (+) V Input & 7: White: (+) Starter Output (-) Parking Lights: White, Pin White 8-pin conn. (driver kick panel) White 0-pin conn. (headlight switch) Directed Digital Solutions TL Directed. All rights reserved.

22 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Scion xb 00 HS CAN High Lt.Green 6 Data OBDII. White 6 A HS CAN Low White 4 Data OBDII. White 6 A SIL White 7 Data OBDII. White 6 A TXCT Green 5 Data Transponder Key Amplifier. Black 7 B CODE Pink 4 Data Transponder Key Amplifier. Black 7 B Parking Lights White 8 (-) Headlight switch. White 0 C Autolight Interrupt Not Equipped. V White 7 (+) Ignition switch. White 8 D Accessory Black 3 (+) Ignition switch. White 8 D Ignition Gray 6 (+) Ignition switch. White 8 D Ignition White 4 (+) Ignition switch. White 8 D Starter White 8 (+) Ignition switch. White 8 D Starter White (+) Ignition switch. White 8 D Keysense Blue (-) Key Warning Switch. White E Lock Lt. Blue 7 (-) Drivers kick panel. White 8 F Unlock Pink 6 (-) Drivers kick panel. White 8 F Directed Digital Solutions TL Directed. All rights reserved.

23 Connecting the module Important! Before connecting the Directed Digital Solutions, it is important to ensure that the proper feature and function programming is selected using the configuration wizard. Visit to use the latest version of the online tool. Flashing a module using your computer:. Disconnect the main module from any (+) V power source, then connect it to your computer using the XKLoader.. Go to using Internet Explorer; the configuration wizard will be displayed automatically. 3. Follow the instructions in the pop up window that will be displayed when the module is detected. Flashing a module using your smartphone or tablet:. Disconnect the main module from any (+) V power source, then connect it to the XKLoader3.. Launch the Directechs Mobile app on your smartphone or tablet. 3. Select FLASH YOUR MODULE and follow the on-screen instructions. When the flashing operation is successful, you can proceed with the instructions below. Manual or automatic transmission selection The yellow loop on the Directed Digital Solutions controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected. Uncut (default): Manual transmission. Cut: Automatic transmission. For safety reasons, all Directed Digital Solutions are shipped ready to use with a manual transmission (the yellow loop is untouched). If the loop is cut after power has been applied, it is necessary to cycle power to the main module (via the white - pin main power harness) so the unit will see the state change on the loop and appropriately configure the transmission type. Ready mode To successfully remote start a vehicle equipped with a manual transmission, the Ready Mode feature must be enabled before exiting the vehicle. Please refer to the Owner s Guide for more details on this required process. Additional connections required for vehicles equipped with a manual transmission (if not supported by firmware) Connection (-) E-Brake Status Input (Black/White, pin ) (-) Door Trigger Input (White/Green, pin 0) OR (+) Door Input (Yellow/ Green, pin ) (AC) Tachometer Input (Violet/White, pin 6) Description Must be connected to a working emergency brake in the vehicle. Although most vehicles have simple (-) trigger emergency brake circuits note some vehicles do not and may require unique integration methodologies. Must be connected to a working door trigger in the vehicle, which monitors all doors. The unit must monitor the door pins to allow the Ready Mode process to be enabled. Note: Some vehicles may require unique integration methodologies for this circuit. For more information, refer to Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.) and learned successfully to the Directed Digital Solutions. 3 Directed Digital Solutions TL Directed. All rights reserved.

24 Optional sensors Note: The sensor port is only active on hybrid systems. The 4-pin sensor port is compatible with a number of different Directed sensors including, but not limited to: Shock Sensor 504D Field Disturbance Sensor 508D Ultrasonic Sensor 509U Note: In the case of 508D, power and ground must be hardwired to the vehicle power and ground should NOT be obtained from the 4-pin sensor port. Each sensor will have its own instructions, which must be followed for installation and adjustment. RF Systems An RF System consists of one or multiple remotes, a Control Center (antenna), and an antenna cable various combinations exist. An RF System allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow the instructions included with the kit for appropriate installation and programming information. When flashing the Directed Digital Solutions, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination. When used in conjunction with SmartStart Disconnect power from the Directed Digital Solutions before connecting the SmartStart module. Failing to do so could damage main module. To enable DD communication between the Directed Digital Solutions and the SmartStart one of the following actions must be executed: SmartStart with Loops The brown loop must be cut. SmartStart with Pigtails The gray wire must be connected to a ground source. Loops Pigtails DO NOT connect the SmartStart -pin power harness when using the Directed Digital Solutions. Power and ground will be provided by the DD connector on main module. Refer to the SmartStart documentation for further details. 4 Directed Digital Solutions TL Directed. All rights reserved.

25 Module programming Refer to "Pre-installation and application warnings" on page 4 for more information and for troubleshooting purposes. To connect the module: Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. Connect all the harnesses to the Directed Digital Solutions, EXCEPT the -pin main power harness. Connect all but the -pin harness 3 Connect the -pin main power harness, and wait until the LED turns ON solid red. Must be connected LAST & Solid 4 Enable the CAN bus by pressing the unlock button on the OEM remote or the unlock button on the inside of the door or by pressing and releasing the door pin switch. The LED starts flashing orange quickly. Enable CAN Bus & Flashes Quickly Note: To skip bypass, wait until the LED turns ON solid orange, then press the programming button 5 times, before proceeding with the next step to continue programming. This will only program convenience features then proceed to step 8. 5 Insert the key in the ignition barrel. The LED turns OFF. Wait until the LED turns back ON solid orange to indicate the key is in learning mode (this may take up to 0 seconds). Key IN OFF ON START & Off & Solid Note: If the LED turns ON solid green, then shuts OFF, go to step 0. A module has already been programmed into the vehicle. 6 Turn the ignition ON. The LED starts flashing green quickly after a few seconds (this may take up to 5 seconds). Key IN OFF ON START & Flashes Quickly 7 Turn the key to OFF and remove the key from the ignition barrel. The LED keeps flashing green quickly. Wait for the LED to flash orange slowly (this may take up to 0 seconds). Key OUT OFF ON START & Flashes Quickly & Flashes Slowly 8 Insert the key and turn the ignition ON then OFF, before removing the key. The LED starts to flash green (slowly). Key IN OFF ON START & Key OUT OFF ON START & Flashes Slowly 9 Wait for LED to turn ON solid green or orange for 3 seconds, before shutting OFF (this may take up to 90 seconds). Green: The bypass was successfully programmed. Orange: The bypass programming was skipped in favor of only programming the convenience features. OR & Solid x 3 secs Solid x 3 secs Off 0 Pair remotes (if applicable). For information on how to pair a specific remote, please refer to its corresponding owner documentation, which can be found inside the product packaging of the complete system or on Pair remotes* By default, the tachometer is preprogrammed for the vehicle. For instructions on how to program tach, see page 9. Initialize tachometer * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. 5 Directed Digital Solutions TL Directed. All rights reserved.

26 LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module programming LED Description Troubleshooting Module has no power. Make sure the DD harness is connected and that Volt is present between the red and black wires. If Volt is present, the module may be defective. Waiting to begin the programming sequence. Ensure the correct programming procedure is being followed. Initialization failed. Reset the module and complete the programming again. If the issue persists, please contact Technical Support. Transponder functions were skipped. (If compatible) when the RXT mode is not desired or convenience features are needed, please reset and reprogram the module. All required CAN networks has been detected. Normal operation. of CAN networks has been detected. Normal operation. KeyGO initiated. Please follow the steps indicated in "Pre-installation and application warnings" on page 4 to complete the KeyGO programming. Solid green x 3 secs Module was successfully programmed with all functions. Normal operation. Solid orange x 3 secs Module was successfully programmed without transponder functions. Normal operation. Off Solid red Flashes red & green Solid orange Flashes green Flashes orange Flashes orange slowly Module programming Error codes LED Description Troubleshooting CAN not detected. Check the CAN Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. J850 not detected. Check the J850 wire connection. Wake up the data bus by turning the ignition on and try again. CAN not detected. Check the CAN Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Bypass data not detected. Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure the vehicle still operates correctly using the factory key. Bypass processing error. The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support. ISO not detected. The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" on page 8 to check the connections. ISO not detected. The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" on page 8 to check the connections. MUX not detected. The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" on page 8 to check the connections. (Flashes red, red, then orange) x Detection of key failed. Check SIL & Data connection. (Flashes red, red, then orange) x Sub key is detected. Insert master key and retry. (Flashes red, red, then orange) x 3 Registration failed. Check SIL & Data connection or car does not support registration process. Flashes red x Flashes red x Flashes red x Flashes red x 3 Flashes red x 4 Flashes red x 5 Flashes red x 6 Flashes red x 7 6 Directed Digital Solutions TL Directed. All rights reserved.

27 External module synchronization LED Description Troubleshooting (Flashes red, red, then orange) x 0 OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. Active Ground When Running (Status) LED Description Troubleshooting Flashes green Ground When Running (Status) command received. The module has initialized the remote start sequence. Flashes red & orange Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence. Flashes green quickly Start ON command received. The module has received the Start ON command and is processing the remote start sequence. PTS shutdown error. The PTS output from the module was not activated due to safety protection. CAN bus incorrectly detected. Verify the CAN and CAN connections. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" on page 8 to check the connections. Description Troubleshooting Flashes red x 0 Flashes red x Commands LED Flashes orange x Flashes orange x Flashes orange x 3 Flashes orange x 4 Flashes orange x 5 Flashes orange x 6 LOCK command received. UNLOCK command received. TRUNK command received. AUX command received. If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or DD. AUX command received. AUX3 command received. Shutdown codes LED Flashes green x Flashes red x Flashes red x Flashes red x 3 Flashes red x 4 Description Troubleshooting Takeover successful. Normal operation. Runsafe was not disabled. No UNLOCK command was received prior to opening the door, or the 45 second timer expired in takeover mode. Brake was not detected. The brakes were not detected, which prevents the system from shutting down the vehicle. Smart key was not detected. The smart key was not detected, which prevents the system from shutting down the vehicle. Speed was detected. The vehicle was detected as moving, which prevents the system from shutting it down. Analog error codes LED Description Troubleshooting Flashes red, green & orange DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. 7 Directed Digital Solutions TL Directed. All rights reserved.

28 Soft reset A module reset will only erase the steps performed in "Pre-installation and application warnings" on page 4. The firmware and settings flashed to the module will not be affected. If required for your installation, connect all the harnesses to the Directed Digital Solutions, EXCEPT the -pin main power harness. Press and hold the programming button, then connect the -pin harness to the module. Connect all but the -pin harness Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red. Solid & Release & Solid Hard reset Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings may need to be reconfigured. Connect your module to a computer and use the web configuration tool to edit its programmable features. If required for your installation, connect all the harnesses to the Directed Digital Solutions, EXCEPT the -pin main power harness. Press and hold the programming button, then connect the -pin harness to the module. Connect all but the -pin harness After 3 seconds the LED turns ON solid orange. Keep holding the programming button until the LED flashes red, then orange slowly. Solid & Hold & Flashes 3 Release the programming button. The LED turns ON solid red. Release & Solid 8 Directed Digital Solutions TL Directed. All rights reserved.