Important! This product is NOT compatible with vehicles equipped with a manual transmission.

Transcription

1 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The TL firmware for DBALL is an all-in-one door lock and override module compatible with specific Lexus and Toyota vehicles. This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a Plug & Play (TLTH/THTOD) T-Harness (optional). This solution offers three () configuration options to control your system: x OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately). - Refer to Quick Reference Guide (QRG) at the end of this guidefor more information on how to use the various features offered with this product. - Compatible with Plug&Play installation of optional T-Harness TLTH/THTOD (sold separately). - No takeover feature is available on Push-To-Start vehicles. The vehicle will shut down as soon as a door is opened. Note: Keyless and SmartKey will remain functional during remote start. Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. Important! This product is NOT compatible with vehicles equipped with a manual transmission. Index Vehicle Application Guide... OEM Remote Starter Detection Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Type... Type... SmartStart/XL0 Installation Notes... Programming Module Programming... Module Reset... Hard Reset... Feature & Option List... Feature Programming... LED Diagnostics & Troubleshooting... Parking Light Error Codes... Limited One-Year Consumer Warranty Quick Reference Guide... 9 SmartStart Compatible SmartStart is equipped with DD, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information. Toyota and Lexus are registered trademarks and property of their respective companies.

2 Vehicle Application Guide Page The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control Lexus ES 50 (Smart Key) Toyota Camry (Smart Key) Camry Hybrid Corolla (Smart Key) Highlander (Smart Key) Highlander Hybrid RAV (Smart Key) DL-Door Unlock DL-Driver Priority Unlock DL-Hatch Glass Release DL-Trunk / Hatch Release RS-x LOCK START (Start control using OEM Remote) RS-Remote Start Ready RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-Ignition Status Legend: DL: OE Door Lock & Alarm Controls PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status

3 OEM Remote Starter Detection Page How to Know if the Vehicle is Equipped with an OEM Remote Starter - An ENGINE STARTER sticker should be on the remote. - Remote start the OEM remote starter: Press the remote control s lock button twice within seconds, then press and hold the lock button for seconds. The parking lights flash after seconds. The engine starts and the parking lights flash repeatedly for 0 seconds. ENGINE STARTER x & Press & Hold for seconds If the Vehicle is Equipped with an Add-On Lexus/Toyota OEM Remote Starter The factory remote starter must be permanently disconnected before programming the Directed interface as both modules cannot coexist. See locating the OEM Remote Starter below. To remote start the engine, the hood, the hatch and all doors must be closed. Locating the OEM Remote Starter Installation Type Vehicle OEM Remote Starter & Connector Location Toyota Camry (Smart Key) Behind glove box & Passenger kick panel. Toyota Camry Hybrid (Smart Key) Behind glove box & Passenger kick panel. Toyota Corolla (Smart Key) Behind glove box & Passenger kick panel & Junction Box & Steering column. Toyota Highlander (Smart Key) Behind glove box & Passenger kick panel. Toyota Highlander Hybrid (Smart Key) Behind glove box & Passenger kick panel. Toyota RAV (Smart Key) Behind glove box & Junction Box.

4 Installation Type with TLTH/THTOD T-Harness Page Refer to the Wiring Reference Chart section on page 6 for more information on specific wiring and connections. OBDII Diagnostic Connector TLTH/THTOD (optional) Note: Hood pin only required on vehicle not equipped with a factory hood pin. Hood Pin Main Body ECU (white conn. under drivers dash) Remote Start Safety Override Switch [] (-) Push-to-Start: Pin 7 ENGINE START STOP OR (+) STSW: Pin or 6 PTS Switch (black conn. behind PTS button) (+) Start Stop Switch Output: Yellow: 8 [] (-) Push-to-Start Output: Green/Black: (-) Parking Lights Output: Red/Black: 0 6: White/Black: (-) Hood Headlight Switch (white conn. at headlight switch) RF Prog. Button LED DBALL (-) Parking Lights: Pin Neutral Safety Switch You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] Connection required only if Pit Stop/Idle mode is desired. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

5 Installation Type Page 5 Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL. Refer to the Wiring Reference Chart section on page 6 for more information on specific wiring and connections. Main Body ECU (white conn. under drivers dash) (+) STSW: Pin or 6 6 Headlight Switch (white conn. at headlight switch) OR 7 OBDII Diagnostic Connector (-) Ground: pin 8 9 HS CAN Low: pin HS CAN High: pin 6 6 (+) V: pin 6 Note: Hood pin only required on vehicle not equipped with a factory hood pin. Hood Pin 0 9 [] Autolight: Green or Yellow, pin 9 CUT (-) Parking Lights: Pin 8 [] (-) Push-to-Start: Pin 7 ENGINE START STOP HS CAN High: Tan/Black: HS CAN Low: Tan: (+) V: Brown: 7 (+) Start Stop Switch Output: Yellow: 8 [] Autolight Interrupt (conn. side): Orange/Red: 0 [] Autolight Interrupt (vehicle side): Yellow/Red: (+) V: Red: (-) Ground: Black: [] (-) Push-to-Start Output: Green/Black: PTS Switch (black conn. behind PTS button) 0 Remote Start Safety Override Switch 6: White/Black: (-) Hood (-) Parking Lights Output: Red/Black: RF Prog. Button DBALL LED Neutral Safety Switch You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] Connection required only if Pit Stop/Idle mode is desired. [] Connection required only if vehicle is equipped with Autolights. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

6 Type - Vehicle Wiring Reference Chart Page 6 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Lexus ES 50 (Smart Key) STSW Gray or Violet or 6 (+) Main body ECU. White 0 A Push-to-Start Blue 7 (-) PTS switch. Black B V Tan 6 (+) OBDII. White 6 C HS CAN High Red/Black 6 Data OBDII. White 6 C HS CAN low White Data OBDII. White 6 C Parking Lights Black 8 (-) Headlight switch. White 0 D Autolights Yellow 9 Cut Headlight switch. White 0 D Toyota Camry (Smart BlueKey) STSW Red or Violet or 6 (+) Main body ECU. White 0 A Push-to-Start Blue 7 (-) PTS switch. Black B V Blue 6 (+) OBDII. White 6 C HS CAN High Black 6 Data OBDII. Black 6 C HS CAN low White Data OBDII. Black 6 C Parking Lights Black 8 (-) Headlight switch. White 0 D Autolights Green 9 Cut Headlight switch. White 0 D Toyota Camry Hybrid STSW Gray or 6 (+) Main body ECU. White 0 A Push-to-Start Blue 7 (-) PTS switch. Black B V Blue 6 (+) OBDII. White 6 C HS CAN High Black 6 Data OBDII. Black 6 C HS CAN low White Data OBDII. Black 6 C Parking Lights Black 8 (-) Headlight switch. White 0 D Autolights Green 9 Cut Headlight switch. White 0 D Toyota Highlander (Smart Key) STSW Gray or Violet (+) Main body ECU. White 0 A Push-to-Start Pink 7 (-) PTS switch. Black B V Green 6 (+) OBDII. White 6 C HS CAN High Black 6 Data OBDII. Black 6 C HS CAN low White Data OBDII. Black 6 C Parking Lights Lt. Blue 8 (-) Headlight switch. White 0 D Autolights Green 9 Cut Headlight switch. White 0 D Toyota Highlander Hybrid STSW Gray or Violet (+) Main body ECU. White 0 A Push-to-Start Pink 7 (-) PTS switch. Black B V Green 6 (+) OBDII. White 6 C HS CAN High Black 6 Data OBDII. Black 6 C HS CAN low White Data OBDII. Black 6 C Parking Lights Lt. Blue 8 (-) Headlight switch. White 0 D Autolights Green 9 Cut Headlight switch. White 0 D

7 Installation Type with TLTH/THTOD T-Harness Page 7 Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL. Refer to the Wiring Reference Chart section on page 9 for more information on specific wiring and connections. OBDII Diagnostic Connector TLTH/THTOD (optional) Note: Hood pin only required on vehicle not equipped with a factory hood pin. Hood Pin Main Body ECU (white conn. under drivers dash) Remote Start Safety Override Switch [] (-) Push-to-Start: Pin 7 ENGINE START STOP PTS Switch (black conn. behind PTS button) (+) STSW: Pin (+) Start Stop Switch Output: Yellow: 8 [] (-) Push-to-Start Output: Green/Black: (-) Parking Lights Output: Red/Black: 0 6: White/Black: (-) Hood Headlight Switch (white conn. at headlight switch) RF Prog. Button LED DBALL (-) Parking Lights: Pin Neutral Safety Switch You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] Connection required only if Pit Stop/Idle mode is desired. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

8 Installation Type Page 8 Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL. Refer to the Wiring Reference Chart section on page 9 for more information on specific wiring and connections. Main Body ECU (white conn. under drivers dash) (+) STSW: Pin OBDII Diagnostic Connector (-) Ground: pin 8 9 HS CAN High: pin 6 6 Note: Hood pin only required on vehicle not equipped with a factory hood pin. Hood Pin Headlight Switch (white conn. at headlight switch) HS CAN Low: pin (+) V: pin 6 Remote Start Safety Override Switch 0 9 [] Autolight: Pin 9 CUT (-) Parking Lights: Pin 8 [] (-) Push-to-Start: Pin 7 ENGINE START STOP HS CAN High: Tan/Black: HS CAN Low: Tan: (+) V: Brown: 7 (+) Start Stop Switch Output: Yellow: 8 [] Autolight Interrupt (conn. side): Orange/Red: 0 [] Autolight Interrupt (vehicle side): Yellow/Red: (+) V: Red: (-) Ground: Black: [] (-) Push-to-Start Output: Green/Black: PTS Switch (black conn. behind PTS button) 0 6: White/Black: (-) Hood (-) Parking Lights Output: Red/Black: RF Prog. Button DBALL LED Neutral Safety Switch You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] Connection required only if Pit Stop/Idle mode is desired. [] Connection required only if vehicle is equipped with Autolights. With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

9 Type - Vehicle Wiring Reference Chart Page 9 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Corolla (Smart Key) STSW Black or White (+) Main body ECU. White 9 A Push-to-Start White 7 (-) PTS switch. Black B V Green 6 (+) OBDII. White 6 C HS CAN High Lt. Green 6 Data OBDII. White 6 C HS CAN low White Data OBDII. White 6 C Parking Lights Brown or White 8 (-) Headlight switch. White 0 D RAV (Smart Key) STSW Red (+) Main body ECU. White 9 A Push-to-Start White 7 (-) PTS switch. Black B V Blue 6 (+) OBDII. White 6 C HS CAN High Black 6 Data OBDII. White 6 C HS CAN low White Data OBDII. White 6 C Parking Lights White 8 (-) Headlight switch. White 0 D Autolights Green 9 Cut Headlight switch. White 0 D

10 SmartStart/XL0 Installation Notes Page 0 The DBALL Remote Start Ready (RSR) solution offers three () configuration options to control your system: x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL0. SmartStart Revision A SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (White & Brown or Blue) Cut Brown or Blue Loop OR DBALL CABLE pins DD ( pins, white) pins, not used LED SmartStart The modules must be connected in a specific order. Refer to the Module Programming section for more information. SmartStart Revision B SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (Gray & White) Connect Gray wire to (-) Ground 5 pins DBALL CABLE pins pins, not used THIS SIDE UP DD ( pins, white) LED The modules must be connected in a specific order. Refer to the Module Programming section for more information. RF Kit The optional XL0 and antenna are not included and MUST be purchased separately. DBALL XOVER LED XL0 Prog. Button Antenna. Use the DD Crossover (XOVER) cable that is provided with XL0, and NOT the one in the DBALL package.. The modules must be connected in a specific order. Refer to the Module Programming section for more information. RF Kit & PKE Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (N0T) for detailed wiring information. RF Kit, PKE & SmartStart BT Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (N0T) for detailed wiring information.

11 Module Programming Page Refer to the LED Diagnostics section on pages 5-6 for more information and for troubleshooting purposes. Important Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step. Note: Before connecting either the XL0 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version.5 or higher). Visit to download the latest version of the application. Warning! To take advantage of advanced features, you must use XpressVIP.5 (and higher) or the Directechs Mobile app. Flashing a module using your computer:. Connect the interface module to your computer using the XKLoader.. Go to using Internet Explorer, and select the Config for RSR button.. Follow the instructions to select your vehicle, installation type, and configure your options.. Once you have configured the firmware options, click on the FLASH button. Flashing a module using your smartphone or tablet. Connect the interface module to your XKLoader.. Launch the Directechs Mobile app on your smartphone or tablet.. Select FLASH YOUR MODULE and follow the on screen instructions. When the flashing operation is successful, you can proceed with the programming instructions below. SmartStart Installation The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL. a. To ensure that the DD communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart). b. Do NOT connect the -pin harness (on SmartStart). Power and ground will be provided by the DBALL DD connector. Connect SmartStart to DBALL using the DD port. OR XL0 Installation Connect XL0 to DBALL using the DD port. SmartStart XL0 DD 0-pin DD 0-pin Connect the 0-pin, -pin and -pin harnesses to DBALL, then wait until the LED turns ON solid red. st DD 0-pin rd nd -pin -pin & Solid Press the PTS button twice to turn the ignition ON. The LED flashes red slowly for few seconds to indicate the key is in learning mode. The LED turns ON solid green for seconds, and then shuts OFF*. * If the module flashes Orange, your vehicle is equipped with a factory remote starter. See section OEM Remote Starter Detection on page. ENGINE START STOP PUSH x & Red slowly & Solid Green x secs Press the PTS button once more to turn the ignition OFF. The module is successfully programmed. ENGINE START STOP PUSH x & Off You have successfully completed the module programming sequence.

12 Module Reset Page A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected. If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. st DD 0-pin th nd rd -pin -pin Wait seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red. & & Hard Reset Solid Release Solid Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and DD options) may have to be reconfigured. See the Feature & Option List section of this guide. If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. st DD 0-pin th nd rd -pin -pin Wait seconds until the LED turns ON solid orange, and wait 0 more seconds until the LED starts to flash orange and red. Solid & Release the programming button. The LED turns ON solid red. Release & Solid

13 Feature & Option List Page It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on The web offers more options such as RSR; however, manual configuration of the features is possible using the information on this page. * Default option Feature Operation / Option Description RF Output Type Unlock Driver Priority Trunk Aux. Disabled* Module is connected to a remote starter using a standard installation.. RFTD Output Module is connected to an XL0 using an RSR or RXT installation (when available).. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).. Driver Priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.. All Unlocks all doors on first press.. Trunk* Will pop the trunk if available..tail Glass Opening Will pop the tail gate if available.. Trunk Will pop the trunk if available.. Tail Glass Opening* Will pop the tail gate if available. The OEM alarm will not be controlled by DBALL upon remote start. No disarm. Disabled or arm command will be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter. Smart OEM Alarm Control will behave like a standard Safelock feature on a. Safelock remote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown. 5 Smart OEM Alarm Control. Enabled* Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm control must often be done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with this option and will make it invisible to the user.

14 Feature Programming To enter feature programming routine - Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after seconds). Release the Programming button. - The LED will flash green once slowly to indicate the feature number is. After a short delay, the LED flashes red rapidly to indicate the current option of feature (i.e. x green followed by x red indicates feature is set to option ). The flashing sequence will repeat until a new command is entered. Changing feature options - Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the DBALL in RSR using x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 0-pin harness to ground will change the option for the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered. Accessing another feature - Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered. When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option. Once a feature is programmed - Other features can be programmed. - The feature programming can be exited. Programming Button Exiting feature programming - No activity for 0 seconds; after 0 seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence. OR - Press and HOLD the programming button for seconds. After seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence. Page

15 LED Diagnostics & Troubleshooting Page 5 LED Description Troubleshooting Module Programming Off Module has no power. Make sure the DD harness is connected or that the Volt is present between the red and black wires. If the Volt is present, the module may be defective. Solid red Waiting to begin the programming sequence. Ensure the correct programming procedure is being followed. red & green Solid orange green Initialization failed. Transponder functions were skipped. All required CAN networks has been detected. Reset the module and complete the programming again. If the issue persists, please contact Technical Support. (If compatible) when RXT mode is not desired or convenience features are needed, please reset and reprogram the module. Normal operation. orange orange slowly Solid green x secs of CAN networks has been detected. Normal operation KeyGO initiated. Module was successfully programmed with all functions. Normal operation Please follow the steps indicated in Module programming to complete the KeyGO programming. Solid orange Module was successfully programmed without x secs transponder functions. Module Programming - Error Codes red x red x red x red x CAN not detected. J850 not detected. CAN not detected. Bypass data not detected. Normal operation. Check the CAN Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Check the J850 wire connection. Wake up the data bus by turning the ignition on and try again. Check the CAN Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure the vehicle still operates correctly using the factory key. red x red x 5 red x 6 red x 7 Bypass processing error. ISO not detected. ISO not detected. MUX not detected. The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support. The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections.

16 Page 6 LED Description Troubleshooting External module synchronization ( red, red then orange) x 0 OBDII feature is not supported. Activation Ground When Running (Status) green Ground When Running (Status) command received. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. The module has initialized the remote start sequence. red & orange green quickly red x 0 red x Commands orange x orange x orange x orange x orange x 5 orange x 6 Ignition ON command received. Start ON command received. PTS shutdown error. CAN bus incorrectly detected. LOCK command received. UNLOCK command received. TRUNK command received. AUX command received. AUX command received. AUX command received. The module has received the Ignition ON command and is processing the remote start sequence. The module has received the Start ON command and is processing the remote start sequence. The PTS output from the module was not activated due to safety protection. Verify the CAN and CAN connections. Refer to Installation (wiring diagrams & vehicle wiring reference charts) to check the connections. If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or DD. Shutdown codes green x red x red x red x red x RSR codes red x 7 red x 9 Takeover successful. Runsafe was not disabled. Brake was not detected. Smart key was not detected. Speed was detected. x OEM Lock Remote Start Activation was attempted when RFTD feature is disabled. Feature error. Normal operation. No UNLOCK command was received prior to opening the door, or the 5 second timer expired in takeover mode. The brakes were not detected, which prevents the system from shutting down the vehicle. The smart key was not detected, which prevents the system from shutting down the vehicle. The vehicle was detected as moving, which prevents the system from shutting it down. Activated from Web automatically when using RSR flash tool or can be done manually. Refer to feature programing section for more information. An RSR feature file mismatch was detected. Please contact Technical Support.

17 Parking Light Error Codes Page 7 The parking lights on your vehicle will flash a specific number of times seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below. Diagnostic Runtime expired. Over-rev shutdown. Low/No RPM. Transmitter shutdown. 5 Brake shutdown. 6 Hood shutdown/remote start safety override switch is ON*. 7 Remote start safety override switch is ON*. * If the vehicle hood status is supported through data, it will also report a 7 flash safety override code.

18 Limited One Year Consumer Warranty Page 8 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold AS-IS and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED s website at: This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. Protected by U.S. Patents: 5,79,55; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,75,7 B; 6,97,7 B; 6,6,876 B; 6,9,5 B; 6,59, B; 6,696,97 B; 6,756,885 B; 6,756,886 B; 6,77,67 B; 6,8,89 B; 6,9,750 B; 7,00,0 B; 7,05,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068,5 B; 7,05,679 B; Cdn. Patent:,0,8;,,99;,5,0;,5,0;,5,07;,5,08;,5,0;,0,97;,6,670;,5,089; European Patent:,05,8; Pat. Pending:,9,06. Made in Canada.

19 Quick Reference Guide DBALL-TL Remote Start Ready (RSR) Installation Remote Start Ready (RSR) Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. List of Available Commands Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information. Vehicle Takeover Note: Takeover feature is not available on Push-To-Start vehicles. The engine will stop when a door is opened. x OEM Lock Remote Start Activation This solution includes the option to remote start your vehicle by pressing the Lock button times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button times once more. Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it. Button(s) x + x + Actions Press & hold for second to lock. Press & hold for second to unlock. Press & hold for second to remote start. Press & hold for 5 seconds to activate the trunk release (optional). Press once, then to activate the rear hatch/tail glass release (optional).* Press times, then to activate the panic mode. Parking Light Error Codes The parking lights on your vehicle will flash a specific number of times seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below. x + Press once, then to reset the remote starter runtime. * This output is configurable. see your authorized installation center for more information. Diagnostic Runtime expired. Over-rev shutdown. Low/No RPM. Transmitter shutdown. 5 Brake shutdown. 6 Hood shutdown/remote start safety override switch is ON*. 7 Remote start safety override switch is ON*. * If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.

20 Quick Reference Guide DBALL-TL Remote Start Ready (RSR) Installation SmartStart Compatible Notes This system is compatible with Directed SmartStart.0. For a complete list of supported features, please visit What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system: Ÿ Lock/Arm Ÿ Unlock/Disarm Ÿ Remote Car Starter Ÿ Trunk Release Ÿ Panic Ÿ Aux Channels You can also control multiple vehicles great for families and assign more than one user to control a vehicle. It's easy with SmartStart! But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more..0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of -way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet. For more information, visit