Platform: XK09 Firmware: DLHO4

Transcription

1 DL doorlock INTERFACE Upgradable Door Lock Alarm Interface Downloadable Firmware for Platform XK09: DLPKGM, DLGM5X, CHRYSLER, PLXR, PKN3, DLVW1, DLHO4, DLHO5, DLHY, DLKIA1, DLKIA2, DLCH2, DLCH3, DLCH4. Installation Guide Door lock only module that interfaces directly with Honda and Acura to provide features compatible with sliding doors, motorized trunks/hatches, and factory alarms. Index Vehicle Compatibility Chart... Installation Procedure Overview... Wiring Diagram.... Vehicle Wiring Reference Chart... Programming the Module... User Configuration - Optional Programming Warranty Update Alert Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Acura and Honda are registered trademarks and property of their respective companies. TECHNICAL SUPPORT / INFORMATION web resources:

2 Vehicle Compatibility Chart Page 2 Vehicle Application Guide 2010 Acura CSX X X X X RDX X X X X TL X X X X X TSX X X X X X Honda Accord X X X X X Accord Hybrid X X X Civic X X X X X Civic Hybrid X CRV X X X X Odyssey X X X X X X Ridgeline X X X X X To see a list of available features for each vehicle, visit

3 Installation Procedure Overview Page 3 Please Note: Failure to proceed in the following order could result in possible vehicle damage. If your remote start system has D2D Jumpers, make sure both Jumpers are in the horizontal position Wiring Make all the connections as per the provided wiring schematics, either in W2W or D2D. Connect the remote starter to the vehicle Make the necessary connections in the vehicle, as instructed in the vehicle-specific guides. Power up the XK09 If connected in D2D Connect the 4-pin D2D harness first, then connect the 20-pin harness. Once done, the interface red LED will turn ON. If connected in W2W Connect the 20-pin harness. Caution! The 20-pin connector can be easily plugged in backwards. 4 Module programming See details on page 5.

4 Wiring Diagram Page 4 See the Vehicle Wiring Reference Chart on page Blue/White Violet/Black Light Green White/Violet Blue Red/White (-) Ground When Running (Status)* (-) Driver sliding door* (-) Lock* (-) Passenger sliding door* (-) Unlock* (-) Trunk* Single Wire CAN Green Red Black (+) 12 Volt* XK09 Back Side (+) 12 Volt RX (-) Ground TX D2D connector wire side view PIN connector wire side view USB CABLE USB PORT (-) Ground* +12VDC Internet XKLOADER2 Option A - Firmware Upgrades Use with D2D harness XKD2D65. XL202 XL202** Antenna ** Sold separately. Option B - Range Extender Connection Use with D2D harness HARD2D Rev. 3. Option C - Plug D2D Harness Directly Into Remote Starter 04 Blue/Red Gray Green (-) Hood Detection Output* (-) Trunk Detection Output* (-) Door Detection Output* Programming button 01 4 PIN connector wire side view XK09 Front Side * These wires are not required in D2D.

5 Vehicle Wiring Reference Chart Page 5 Vehicle Years Data Wire BCM Location Acura CSX Pink Pin 4 in 7-pin Transponder connector RDX Pink Pin 4 in 7-pin Transponder connector TL Brown/Black Pin 4 in 21-pin DKP connector (bottom row) TSX Brown/Red Pin 4 in 21-pin DKP connector (bottom row) Honda Accord Brown/Red Pin 4 in 21-pin DKP connector (bottom row) Accord Hybrid Dark Green Pin 4 in 21-pin DKP connector (bottom row) Civic Pink Pin 4 in 7-pin Transponder connector Civic Hybrid 2006 Pink Pin 4 in 7-pin Transponder connector CRV Pink Pin 4 in 21-pin DKP connector (bottom row) Odyssey Dark Green/Red Pin 4 in 21-pin DKP connector (bottom row) Ridgeline Brown/Black Pin 4 in 21-pin DKP connector (bottom row) Connector location: DKP: Green 21-pin connector above relays at the fuse box, in the driver kick panel. Transponder: at the ignition switch. Module Programming 1 Once all the wires are properly connected, plug the wire connector into the module. If connected in D2D Connect the 4-pin D2D harness first, then connect the 20-pin harness. Once done, the interface red LED will turn ON. If connected in W2W Connect the 20-pin harness. Connect module On Solid 2 Insert 3 Turn the key into the ignition barrel and turn it to the Ignition () position. The LED turns to confirm that the module was successfully programmed. the key to the position and remove it from the ignition barrel. Key at Remove Key Off Caution! The 20-pin connector can be easily plugged in backwards.

6 User Configuration - Optional Programming Page 6 USER MODES are identified by a slow LED flashing pattern. For example, 1 slow flash = Mode1 and 2 slow flashes = Mode 2. 1 Insert the key into the ignition at the position and hold the Programming button down for at least 2 seconds. The LED flashes rapidly for 2 seconds to confirm you are in programming mode. Key at Press Hold Flash 2 Secs 2 Release the Programming button. The LED first flashes a number of times slowly to indicate the MODE. It then flashes a number of times quickly to indicate the OPTION. Release No. of Slow Flashes = Mode No. of Quick Flashes = Option 3 To change the MODE, press once on the Programming button. The LED confirms the MODE with a number of slow flashes. Only modes 1, 6 and 8 are available. To change the OPTION in the selected MODE, press LOCK or 4 UNLOCK on the alarm or remote starter transmitter. The LED confirms the OPTION with a number of quick flashes. See the list of options at the bottom of this page. ( Press Once or Press ( No. of Slow Flashes = Mode No. of Quick Flashes = Option 5 To exit the programming mode, hold the Programming button down until the LED flashes once quickly. Press Hold Flashes Once 6 Remove the key from the ignition barrel. Remove Key Mode 1 - Driver door priority Mode 6 - Lock when remote starter stops Mode 8 - Reset *Option 1: 1st pulse unlocks all doors. *Option 1: Activate. *Option 1: No reset. Option 2: 1st pulse unlocks driver door, 2nd pulse unlocks all doors. Option 2: Deactivate. Option 2: Complete reset of the options and module. * Default option.

7 Limited One-Year Consumer Warranty Page 7 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES ER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connexion with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. PROTECTED BY U.S. PATENTS: 5,719,551; 6,011,460 B1 *;6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7, 0 4 6, B 1 ; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; CDN. PATENT: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2, 4 2 0, ; 2,426,670; 2,454,089 EUROPEAN PATENT:1,053,128 PAT. PENDING: 2,291,306; MADE IN CANADA