V

Size: px

Start display at page:

Download "V"

Samantha Singleton
5 years ago
Views:

1 V

2 Trademark Information LAUNCH is a registered trademark of LAUNCH TECH. CO., LTD. (LAUNCH for short) in China and other countries. All other LAUNCH trademarks, service marks, domain names, logos, and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos, company names of or are otherwise the property of LAUNCH or its affiliates. In countries where any of the LAUNCH trademarks, service marks, domain names, logos and company names are not registered, LAUNCH claims other rights associated with unregistered trademarks, service marks, domain names, logos, and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. You may not use any trademark, service mark, domain name, logo, or company name of LAUNCH or any third party without permission from the owner of the applicable trademark, service mark, domain name, logo, or company name. You may contact LAUNCH by visiting Launch at or writing to Launch Industrial Park, North of Wuhe Rd., Banxuegang, Longgang, Shenzhen, Guangdong, P. R. China, to request written permission to use Materials on this manual for purposes or for all other questions relating to this manual. Copyright Information Copyright 2012 by LAUNCH TECH. CO., LTD. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of LAUNCH. The information contained herein is designed only for the use of this unit. LAUNCH is not responsible for any use of this information as applied to other units. Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this unit, or unauthorized modifications, repairs, or alterations to this unit, or failure to strictly comply with LAUNCH operating and maintenance instructions. LAUNCH shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original LAUNCH Products or LAUNCH Approved Products by LAUNCH. General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners. LAUNCH disclaims any and all rights in those marks. i

3 This unit is made for the purpose of persons who have special techniques and certifications. Disclaimer To take full advantage of the unit, you should be familiar with tires of various kinds. All information, illustrations, and specifications contained in this manual are based on the latest information available at the time of publication. The right is reserved to make change at any time without notice. Safety Precautions This manual is a necessary part of the product. Please read carefully. Keep the manual for later use when maintaining the machine. This machine can only be used for the designated purposes. Never use it for any other purpose. The manufacturer is not held responsible for the damage incurred by improper use or use other than the intended purpose. The equipment can only be operated by qualified personnel with special training. Modification to any components or parts, or use the machine for other purpose without either obtaining the agreement from the producer, or observing the requirement of the instructions may lead to direct or indirect damage to the equipment. This machine should be installed on the stable ground. Keep the back panel at least 0.5m away from the wall for good ventilation. Enough room should be left on both sides of the machine for convenient operation. Do not put this machine in a place with high temperature or moisture, or near the heating system, water tap, air-humidifier or furnace. Do not put the machine near the window with sunlight. Protect the unit with a curtain or shield if necessary. Avoid lots of dust, ammonia, alcohol, thinner or spraying binder. People who are no operating the machines should be kept away when it is used. Use appropriate equipment and tools, protective and safety equipment, including eyeglasses, earplugs and working boots, etc. Pay special attention to the safety marks on the machine. Do not touch or approach the moving parts by hand(s) during operating. Do not remove the safety device or override it. Use #2 lithium lubricants (grease) only within the safety range. Refer to the appendix for the safety data. Before moving the tire changer, contact maintenance personnel. The product is better used under the following conditions: Temperature: 0 ~45 Relative humidity: 30~95% ii

Description of Safety Signs 1 Keep safety for electrified devices.

3 Do not put your hand(s) between the tire and turntable when machine is operated.

5 It is forbidden to put your hand(s) or tools in the claws when they are opened or

4 Description of Safety Signs 1 Keep safety for electrified devices. 2 Do not put your leg(s) between the splitter and the tire when the splitter is used. 3 Do not put your hand(s) between the tire and turntable when machine is operated. 4 Do not put your hand(s) between the MOUNT/DEMOUNT head and the tire. 5 It is forbidden to put your hand(s) or tools in the claws when they are opened or closed. 6 Pedal down to the first gear to perform direct inflating action; the nozzle whiff when you pedal down to the second gear. iii

5 The Position of Safety Signs Please change the safety signs if it gets blurred or lost. When one or more safety signs get lost, don t operate the machine. The safety signs must be kept within the sight of the operator. iv

6 Table of Contents 1. Structure Installation Unpacking Transportation Placing Column Swing arm Return spring Splitter Power and Air Connections Adjusting Pedal adjustment Clamping Unit of the Jaws Splitter Air Pressure Regulator, Gauge and Lubricator Assembly Mount/Demount Head Maintenance Electric Connection Diagram Equipment Explosion Diagrams and Detailed Parts List Recommended Parts List CE Declaration of Conformity v

7 1. Structure Fig1.1 The main operating parts are as shown in Fig Return spring 2- Hexagonal column locking handle 3- Swing arm 4- Hexagonal column 5- Column 6- Mount/demount head 7- Clamping jaw 8- Turntable 9- Clamping cylinder 10- Screw handle 11- Splitter handle 12- Lubricant box 13- Splitter arm 14- Splitter shoe 15- Clamping cylinder control pedal 16- Splitter control pedal 17- Turntable control pedal Accessories provided are as shown in Fig Tire lever 002-Gun inflator with a pressure gauge 003-Brush Fig1.2 1

8 2. Installation Prepare the following tools before installation: two screw wrenches, one set of inner hexagon wrenches, one set of box end wrenches, one plier, one set of screwdrivers and one digital multimeter (for testing voltage). 2.1 Unpacking Unpack according to the instructions on the package. Remove the packing materials and inspect the machine for possible damage or loss of accessories during transportation. Remove the cabinet, column, swing arm and accessory box fitted on the bottom plate and keep them in safety place. Keep the packing materials out the reach of children. Handle in an appropriate way if the packing materials are likely to cause pollution. Caution: The special anti-rust oil applied on the delicate parts may attract dust. Clean in when necessary. 2.2 Transportation Transport with fork lift. Avoid the column and swing arm moving to improper places during transportation. Avoid the excessive tilting in transportation. Drive the fork lift carrying the equipment slowly. Try to keep the machine at the lowest position and make sure it won t overturn in transportation. 2.3 Placing Installation should be in accordance with safety regulations. Install the machine in proximity of power source and air compressed system. Install the machine on level concrete ground. 4 sets of M10*150 anchor bolts are used to fasten the machine onto the ground to avoid vibration and noise. Set enough place (at least 1m in front and on both sides of the machine and 0.5m behind it) for operation and maintenance of the machine. A protective shelter should be built in the case it has to be installed outdoor. Do not operate machine in proximity of flammable gas. Note: For safety and proper operation, keep the machine at least 0.5m away from the wall. 2.4 Column As shown in Fig2.1, the column is connected with the cabinet body through hexagon socket head bolts and washers. 2.5 Swing arm As shown in Fig2.2, the swing arm is connected with the column through one bolt, the two ends of the bolt is locked by one big washer and some cir-clips. 2

Hexagon socket head screws 4 Bolt Cir-clip Washer Washers 8 Fig2.1 Fig2.2 2.

3, before installation you should remove the cap after unscrew the screw on the cap, and

tighten the screw. Cap Screw Return spring 2.7 Splitter Fig2.

The splitter arm and the cabinet body is connected through a bolt, both ends of the bolt

9 Hexagon socket head screws 4 Bolt Cir-clip Washer Washers 8 Fig2.1 Fig Return spring As shown in Fig2.3, before installation you should remove the cap after unscrew the screw on the cap, and install the return spring on the hexagon column, and then assemble the cap back and tighten the screw. Cap Screw Return spring 2.7 Splitter Fig2.3 First install the splitter arm. The splitter arm and the cabinet body is connected through a bolt, both ends of the bolt are locked by cir-clip and washer (Fig2.4). Then put the splitter arm passing through the piston rod at one side of the cabinet body and lock the nut (Fig2.5). Fix the return spring well at last. Cir-clip Piston rod Bolt Return spring Nut Fig2.4 Fig2.5 3

10 2.8 Power and Air Connections Check the power source and the compressed air system are in accordance with the specifications on nameplate. Any electrical connection should be done by professionally trained technician. The power socket should be nearby for convenient operation, at the height of 0.6~1.7m. A voltage stabilizer should be applied to connect power source and the machine in the case of unstable voltage. The machine should be well grounded. 3. Adjusting 3.1 Pedal adjustment Note: The four pedals must be kept at the original position. Press down the pedal to turn the turntable clockwise; Lift the pedal to turn the turntable counter-clockwise; Press down pedal to open splitter; release it to restore; Press down pedal to open the jaws on the turntable; pedal again to move them inward; 3.2 Clamping Unit of the Jaws The position of the jaw on the turntable is controlled by the movement of the piston rod, which in turn is controlled by pedal. There are three levels for pedal. When pedal is placed on high, the piston rod will move inward and pull the jaws moving inward until the minimum. When pedal is placed on low, the piston rod will move outward and pull the jaws moving outward until the maximum 3.3 Splitter The splitter is on the right side of the cabinet. As the procedure requires, press down pedal to start the splitter cylinder, the piston rod will pull the splitter towards the cabinet, with magnitude around 14075N. Release pedal, the splitter will retract. The splitter is able to swing within a certain range. In case the range of swing is not appropriate, adjust the nut (Fig3.1) at the right end of the piston rod. Fig Air Pressure Regulator, Gauge and Lubricator Assembly As shown in Fig3.2, there is a button on the regulator. When pulled up, the pressure can be increased or decreased by turn it clockwise or counter-clockwise. After adjusting the operation pressure, press the button down to lock it. The air cleaner works to filter the water and impurity in the compressed air. When water and impurities run beyond 4

11 the red line, turn open the draining valve to release them. The lubricator is used to add a certain amount of lubricant into gas for the moving parts in the cylinder and regulator. Depress pedal or 3~5 times, a drop of lubricant will fall into the cup in the regulator. If it does not happen, the adjusting screw needs to be adjusted. Fig Mount/Demount Head Checking 1) Mount a 13 inch diameter aluminum alloy rim (preferably new) onto the turntable. 2) Lower the mount / demount head onto the rim and lock. 3) By means of the appropriate gauge kit, check measurements as indicated in Fig.33 (for mount/demount head with roller) and Fig.34 (mount /demount head with insert). Fig3.3 Fig3.4 5

12 Calibration 1) Loosen all screws securing the mount / demount head. 2) Lower the mount / demount head onto the rim and lock. 3) Finger-tighten screws A3-A4 (Fig3.7 and Fig3.8) in order to turn the mount / demount head and obtain the correct position. 4) Tighten screws A1-A2 (Fig3.5, 3.9 mount/demount head with roller; Fig3.6, 3.10 mount / demount head with insert) to tilt the mount / demount head and obtain the correct position and then finger-tighten screw B. 5) Unlock and raise the hexagonal column, then lower it onto the rim and lock again. 6) First tighten screws A1-A2-A3-A4 in torque of 50Nm and check by means of gauges that the measurements remain the same. 7) Lastly, tighten screw B to a torque of 50Nm and carry out checks once again with the gauges. Fig3.5 Fig3.6 Fig3.7 Fig3.8 Fig3.9 Fig3.10 6

depress pedal 15 for 3 or 4 times to bleed the residual compressed air in the machine.

13 4. Maintenance Note: Maintenance can be carried out only by the specialized technician. Before any maintenance is performed, disconnect the power and keep the plug within the sight of the maintenance personnel, and shut off compressed air, push the air valve switch to Off position and depress pedal 15 for 3 or 4 times to bleed the residual compressed air in the machine. To keep the tire changer in good condition and to prolong the work life, it is necessary to do regular maintenance according to the instructions on the User s Manual. Otherwise, the normal operation and reliability of the machine will be affected, or personal injury would be caused. Keep the machine and working area clean and prevent dust or foreign matter from entering the moving parts. Keep the hexagonal column clean and dry (clean with diesel as shown in Fig4.1). Keep the swing arm clean and lubricate it periodically so that it can move expectably. Weekly clean the turntable, jaws, guide ways (Fig4.2); clean and lubricate the column. Weekly lubricate the faying surface between moving parts and rubbing surface with lithium lubricant. Check the oil level in the sprayer regularly. If the oil level does not reach the second line, fill SAE20 (Fig4.3). Clear away the condensed material in the water separator around the sprayer regularly. Regularly check and adjust the tension of the belt. Check all connecting parts and bolts regularly and tighten them if necessary. Regularly check and adjust the hexagonal column to keep the proper distance between the inside of the mount/demount head and the rim. Note: About 15 days after starting to use the equipment, fasten the jaws and positioning bolts A (Fig4.4). Fig4.1 Fig4.2 Fig4.3 Fig4.4 7

14 5. Electric Connection Diagram 8

15 6. Equipment Explosion Diagrams and Detailed Parts List General Assembly Drawing The Body Assembly 9

16 The Splitter Assembly The Control Pedal Assembly 10

17 The Gear Box Assembly The Motor Assembly 11

18 The Pedal Valve Assembly The Big Cylinder Assembly 12

19 The Vertical Column Assembly The Turntable Assembly 13

20 The Small Cylinder Assembly 14

21 NO. NAME QTY NO. NAME QTY 101 Body assembly Screw M10* Vertical column assembly Washer Washer Washer Washer Gear box assembly Bolt M12* Motor assembly Bolt M12* Bolt M10* Turntable assembly Washer Flat bond 10* Nut M Cap Bolt M10* Screw M12* V-belt A Rubber wheel support Body assembly Washer Tire assembly Screw M6* Cushion Front cover Splitter cylinder assembly Screw M6* Bolt Nut M Nut M18* Water jug holder Spring Water jug Bolt M16* Body cover Washer Screw M6* Nut M Body cushion Quick inflator valve assembly Cross bar 1 15

22 NO. NAME QTY NO. NAME QTY 301 Splitter arm Washer Shovel jointing Nut M Cushion Screw M6* Nut M Screw M6* Handle Spring Bushing Bracket jointing Air valve assembly Pedal Screw M6* Long bushing Switch connecting rod Long shaft Bolt M8* Washer Nut M Valve pole holder Bolt M8* Connecting rod Twist spring support Bushing Twist spring Washer Washer Nut M Switch lever Valve assembly Connecting rod shaft Screw M5* Bend board Washer Reverse switch Washer Washer Nut M Washer Nut M Screw M4* Cam Screw M5* Cam support Screw M6*

23 NO. NAME QTY NO. NAME QTY 501 Gear box cover Motor Bearing Z Pulley Gear box cover Motor support Stifled Cushion Bearing Washer Worm Washer Oil seal FB Bolt M8* Bond 6* Pulley Valve Washer O ring Bolt M8* Bushing Pin 8* Valve pole Screw M8* Pin 4* Washer Washer Nut M Bearing Z Piston pole Worm wheel shaft Splitter cylinder cover Bond 14* Splitter cylinder jointing Worm Screw M6* Washer Washer Screw M6* Nut M Rotating union casing Bushing O ring Y ring Rotating union casing Cushion Screw M3* Washer O ring Piston 1 17

24 NO. NAME QTY NO. NAME QTY 912 Y ring M/D head Washer Idler wheel shaft Nut M Pulley O ring Cushion Cushion Column jointing Bolt M10* Cushion Screw M12* Rocker jointing Screw M12* Rocker shaft Washer Turntable jointing Nut M Connecting plate Screw Claw Spring cover Shaft sheath Spring Slide plate Screw M8* Boat jointing Six side shaft Connecting rod jointing Spring Cylinder support jointing Stifled Cylinder assembly Locked board Washer Screw M10* Washer Nut M Screw M10* Washer Eccentricity sheath Locking shaft jointing Washer Adjusting cushion Washer Washer Screw M10* Cushion Washer

25 NO. NAME QTY NO. NAME QTY 1118 Washer Cylinder shell Cylinder cover Cylinder cover Piston Piston pole Connecting rod O ring O ring Y ring Washer Nut M Nut M

7. Recommended Parts List SN ERP Code Picture Part Name Qty.

307990074 1 Upper cover of big cylinder 0602# 307990075 switch lever 0935# 1 307990077

307990102 Air pipe joint 1 307990103 Pipe joint with different diameters 1 228

26 7. Recommended Parts List SN ERP Code Picture Part Name Qty. Remark big cylinder assembly 0204# hose connector(short)0205# Upper cover of big cylinder 0602# switch lever 0935# Screw M10* # Hand wheel Control pedal s valve body Air pipe joint Pipe joint with different diameters water jug holder, # O-ring , # pedal, # cam, #

27 air valve assembly, # twist spring, # reverse switch, # O ring , # Spring cover,# claw, #

28 CE Declaration of Conformity 22

29 Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER S BUSINESS. LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages. Final determination of defects shall be made by LAUNCH in accordance with procedures established by LAUNCH. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein. Disclaimer THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Order Information Replaceable and optional parts can be ordered directly from your LAUNCH authorized tool supplier. Your order should include the following information: 1. Quantity 2. Part number 3. Item description Customer Service If you have any questions on the operation of the unit, please contact us: If your unit requires repair service, return it to the manufacturer with a copy of the sales receipt and a note describing the problem. If the unit is determined to be in warranty, it will be repaired or replaced at no charge. If the unit is determined to be out of warranty, it will be repaired for a nominal service charge plus return freight. Send the unit pre-paid to: Attn: Overseas Department LAUNCH TECH. CO., LTD. Launch Industrial Park, North of Wuhe Rd., Banxuegang, Longgang, Shenzhen, Guangdong, P. R. China 23

V

V1.00.000 2012-09-05 Trademark Information LAUNCH is a registered trademark of LAUNCH TECH. CO., LTD. (LAUNCH for short) in China and other countries. All other LAUNCH trademarks, service marks, domain