Installation manual: CK3100 range TRANSPORTER T5

Transcription

1 Installation manual: TRANSPORTER Parrot MKi + T5 Parrot CK3100 range TRANSPORTER T5 This The VOLKSWAGEN sheet is designed TRANSPORTER to help you T5 with marque the and installation VOLKSWAGEN of a Parrot logo are product the property and is purely of the VOLKSWAGEN for information. France Any Group installation s.a or VOLKSWAGEN performed in compliance AG. This document with the is instructions only valid for appearing the vehicle in model this document TRANSPORTER is done T5 under year the 2002 sole to 2009, responsibility excluding of all the other installer, models who in the is entirely same range responsible and for excluding the quality later of modifications the installation. made All to rights the vehicle reserved by the Copyright manufacturer PARROT SA RCS PARIS May not be reproduced without the authorisation The Parrot brand of Parrot name SA. and Pictures logos are for the information exclusive property only. of Parrot SA.

2 Fitting time (estimated) / Main features Disassembly 15min NO +IGN Mounting kit 20min NO ISO Reassembly 15min NO UNIKA Testing 15min FRONT LOUDSPEAKER TEL mode Total 1h 05min ALL MUSIC mode Tools Plastic trim removal tools FACOM / BOJO -TORX screwdriver - Cutting pliers - Crimping pliers - Multimeter or Test lamp - Wire tie - Electrical tape - Soldering Iron FACOM DX-25 kit (tool no.1) CK range Accessories required MKi range Kram ref. Dealer ref. CK range YY 138 CABL 2 MKi range YY 138 CABL 2 Photos for illustration purposes Updating "Please contact your wholesaler to purchase accessories. A list of wholesalers is available at " To get the most out of your hands-free kit we recommend that you update your software regularly. The update procedure can be found at

3 Disassembly

4 Disassembly Insert the removal tools into the 4 slots in the radio. Press them down until the radio unclips and remove the radio unit with the tools. Unclip the fusebox cover.

5 Finding an ACC wire 1 2 Using a guide, feed an electric wire from the fusebox to the radio housing. 3 Then connect to the 5 amp fuse (located in the middle of the lower row) by means of a 2.5 mm terminal. Connect the +IGN using a male round terminal to the blue wire of the adapter in front of the fuse holder or on the red wire of the or YY138CABL2 adapter.

6 Wiring the microphone Unclip the upper steering wheel cover. Using a guide, feed the cable under the steering wheel cover towards the radio housing. Glue the bracket (supplied) in the centre of the plastic steering wheel cover after degreasing. Then replace the flexible cover.

7 Feeding the accessory cable 1 2 Remove the cover. Feed the cable towards the radio housing. 3 Then block the hole with the cover (provided) on the cable.

8 Fitting the hands-free system 1 / 2 1 Connect the adaptor to the original connector and connect all of the wires to the blue box as shown in the diagram below. Test the assembly before completing fitting and then slide everything behind the air conditioning control unit. Direct adaptor cable

9 Fitting the hands-free system 2 / Unclip the release button cover to the left of the radio. Make a notch using a file or a knife. 4 5! Feed the screen cable via the cover towards the radio. Then glue the mounting (supplied) onto the same button cover after degreasing it (TAKE CARE not to trap the cable).

10 Testing Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob of the remote control, check: 1 - that the menu is displayed on the screen (language or ipod etc). 2 - that the radio system is muted when the kit is in use (click in the blue box). 3 - that the sound through all speakers is properly muted. 4 - that there is sound through the front speakers for spoken menus. 5 - then turn off the ignition, verify that the kit turns off and that the message goodbye is displayed on the screen (otherwise reverse the fuses on the kit power supply harness). 6 - pair a telephone with the kit and make a call (check that both the microphone and the kit are working).

11 Reassembly Refit the system using the following procedure: 1 - replace the fusebox cover. 2 - reconnect the adapter and the aerials behind the radio, and slide them into the housing. 3 - retest to check that the system is working correctly.