* * Inside Toyota Avalon. Tools Required IMPORTANT
|
|
- Elmer Newman
- 5 years ago
- Views:
Transcription
1 Revision 08/02/ Toyota Avalon IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call Crutchfield Technical Support at. Inside... Although reasonable attempts are made to verify the accuracy of the information contained in this MasterSheet, it is presented without warranties or guarantees of any type due to the constantly changing nature of this type of information and running changes in vehicle production. Any person or entity using this information does so at his or its own risk. If you find our instructions are different from your vehicle, or if you have questions, do not continue with your installation. Contact our toll-free technical support for assistance. * * Page 2 Factory Radio Removal 3 OEM Integration 4 Receiver Installation 5 Corner Dash Speakers 6 Center Dash Speaker 7-8 Front Door Speakers 9-10 Rear Door Speakers Rear Deck Woofers 13 Rear Deck Tweeters 14 Wire Splicing Guide Tools Required Phillips Screwdriver Small Flat Blade Screwdriver 10mm 12mm Socket, Ratchet & Extension Panel Tool Needle-Nose Pliers Wire Strippers & Crimp Caps Drill & 1/8 Bit Note: At this time, no aftermarket antenna is available from Crutchfield. A replacement antenna may be purchased from a local dealership.
2 Factory Radio Removal 1. Before proceeding, eject disc(s) from factory unit if present. 2. Set parking brake and disconnect negative battery cable to prevent any electrical short. FIGURE 1 FIGURE 4 3. Starting on the passenger s side, pry out vent/gauge trimpanel to release eighteen (18) clips. Disconnect hazard switch harness, then work trimpanel around steering wheel to remove (Figures 1 & 2). Vent/Gauge Trimpanel Lower Dash Trimpanel 4. Remove two (2) 10mm screws exposed by removal of vent/gauge trimpanel (Figure 3). 5. Pry down lower dash trimpanel to release clips and enough to remove two (2) 10mm screws (Figure 4). 6. Pull out radio/climate control assembly, disconnect and remove (Figure 5). FIGURE 2 (1 of 2 screws shown) Radio/Climate Control Assembly FIGURE 3 (1 of 2 screws shown) FIGURE 5 2
3 OEM Integration This page addresses integrating aftermarket accessories such as R CD Changers, Auxiliary Input Adaptors, ipod Adaptors, etc., with a factory radio system. 1. Remove factory radio following instructions on the previous page. 2. Follow instructions supplied with the accessory device. 3. Connect optional adaptor to input as shown. 4. IMPORTANT: Reconnect all wiring harnesses including airbag, then reconnect battery. Test operation of adaptor and reassemble dash by reversing removal steps. Rear View Factory Radio Input 3
4 Receiver Installation NOTES: Please read first Check to make sure the Crutchfield receiver wiring adaptor plugs into the vehicle receiver harness. If the Crutchfield adaptor is incorrect, please call our Technical Support Department at. A Standard DIN unit is shown. A Double-DIN receiver may also be installed following these steps. 1. Secure receiver to mounting bracket following instructions supplied with the dash kit. 2. Make wiring connections following instructions supplied with the receiver wiring adaptor received from Crutchfield. 3. Hold receiver assembly near dash. Connect receiver wiring adaptor to vehicle harness. Using the antenna adaptor, plug antenna lead into rear of receiver. Receiver Assembly 4. Slide assembly into dash and secure with screws previously removed. 5. IMPORTANT: Reconnect all wiring harnesses including airbag, then reconnect battery. Test operation and reassemble dash by reversing removal steps. 4
5 Corner Dash Speakers NOTES: Please read first Instructions show factory size speakers or speakers with adaptor brackets only. Cutting or fabrication (not shown) will be required for other speaker sizes. IMPORTANT No speaker wiring adaptor is available at this time from Crutchfield for this speaker location. It will be necessary to splice wires in order to install an aftermarket speaker. FIGURE 1 FIGURE 4 1. Starting at the top edge, pry out pillar trimpanel to release clip. Using needle-nose pliers, twist retainer strap to release. Pull trimpanel upward to remove (Figures 1 & 2). Pillar Trimpanel 2. Repeat step one for the opposite side. 3. Pry up dash grille/defroster panel to release clips. Disconnect wiring harness and remove (Figures 3 & 4). FIGURE 2 4. Remove two (2) 10mm screws securing speaker. Pull out speaker, disconnect and remove (Figure 5). FIGURE 5 5. Make wiring connections following instructions on page 14. Return to this page to complete installation. 6. Secure speaker to location with screws previously removed. 7. Test speaker operation and reassemble by reversing disassembly steps. FIGURE 3 Retainer Strap Dash Grille/Defroster Panel 5
6 Center Dash Speaker NOTES: Please read first Instructions show factory size speakers or speakers with adaptor brackets only. Cutting or fabrication (not shown) will be required for other speaker sizes. IMPORTANT No speaker wiring adaptor is available at this time from Crutchfield for this speaker location. It will be necessary to splice wires in order to install an aftermarket speaker. 1. Follow steps 1-3 on the previous page to remove dash grille/defroster panel. 2. Remove two (2) 10mm screws securing speaker. Pull out speaker, disconnect and remove. 3. Make wiring connections following instructions on page 14. Return to this page to complete installation. 4. Secure speaker to location with screws previously removed. 5. Test speaker operation and reassemble by reversing disassembly steps. 6
7 Front Door Speakers NOTES: Please read first Instructions show factory size speakers or speakers with adaptor brackets only. Cutting or fabrication (not shown) will be required for other speaker sizes. 1. Starting at the top edge, pry out sail panel to release one (1) clip and remove (Figure 1). FIGURE 4 2. Remove one (1) retaining clip on front edge of door panel by pressing in center pin, then prying out clip (Figure 2). 3. Pry out screw cover behind door release and remove one (1) exposed phillips screw (Figure 3). 4. Remove one (1) phillips screw and bumper on rear edge of door panel (Figure 4). 5. Pry up power options switch panel to release three (3) clips. Disconnect wiring harness and remove panel (Figure 5). FIGURE 1 FIGURE 2 Sail Panel Continued on the next page. Power Options Switch Panel Screw Cover FIGURE 5 FIGURE 3 7
8 Front Door Speakers (continued) 6. Remove two (2) phillips screws exposed by removal of power options switch panel (Figures 6 & 7). FIGURE 6 7. Pry out sides and bottom of door panel to release nine (9) clips. Disconnect wiring harness, door lock and release cables. Remove panel (Figures 8 & 9). 8. Remove four (4) 10mm screws securing speaker. Pull out speaker, disconnect and remove (Figure 10). 9. Secure new speaker to adaptor bracket. 10. Connect speaker wiring adaptor of replacement speaker to vehicle speaker harness. Secure speaker/bracket assembly to location. 11. Test speaker operation and reinstall door panel by reversing removal steps. FIGURE 7 FIGURE 9 FIGURE 10 SAFETY CHECK Door Lock & Release Cables Check that wires do not interfere with window operation. Test door lock and release operation. Standard Speaker shown. JBL-Equipped speakers are mounted the same way. FIGURE 8 8
9 Rear Door Speakers NOTES: Please read first Instructions show factory size speakers or speakers with adaptor brackets only. Cutting or fabrication (not shown) will be required for other speaker sizes. IMPORTANT No speaker wiring adaptor is available at this time from Crutchfield for this speaker location. It will be necessary to splice wires in order to install an aftermarket speaker. 1. Pry out screw cover behind door release and remove one (1) exposed phillips screw (Figure 1). 2. Remove one (1) phillips screw and bumper on rear edge of door panel (Figure 2). Screw Cover 3. Pry up power options switch panel to release three (3) clips. Disconnect wiring harness and remove panel (Figure 3). FIGURE 1 FIGURE 2 4. Remove two (2) phillips screws exposed by removal of power options switch panel (Figure 4 - this page, Figure 5 - next page). FIGURE 3 FIGURE 4 Continued on the next page. Power Options Switch Panel 9
10 Rear Door Speakers (continued) 5. Pry out sides and bottom of door panel to release seven (7) clips. Disconnect wiring harness, door lock and release cables. Remove panel (Figures 6 & 7). FIGURE 5 6. Remove three (3) phillips screws securing factory speaker/bracket assembly. Pull out assembly, disconnect and remove (Figure 8). 7. Remove two (2) phillips screws securing speaker to bracket (Figure 9). 8. Secure new speaker to factory bracket with screws previously removed. 9. Make wiring connections following instructions on page 14. Return to this page to complete installation. 10. Secure speaker/bracket assembly to location. 11. Test speaker operation and reinstall door panel by reversing removal steps. Door Lock & Release Cables FIGURE 6 FIGURE 8 Standard Speaker shown. JBL-Equipped speakers are mounted the same way. FIGURE 7 SAFETY CHECK Check that wires do not interfere with window operation. Test door lock and release operation. FIGURE 9 10
11 Rear Deck Woofers NOTES: Please read first Instructions show factory size speakers or speakers with adaptor brackets only. Cutting or fabrication (not shown) will be required for other speaker sizes. 1. Disconnect negative battery cable. 2. Pull up front edge of rear seat bottom cushion to release two (2) clips and remove cushion (Figure 1). (1 of 4 bolts shown) 3. Remove four (4) 12mm bolts along bottom edge of rear seat back (Figure 2). 4. Work seat belts through slots in seat belt retainers in rear seat back (Figure 3). FIGURE 1 FIGURE 2 5. Lift rear seat back to clear three (3) hooks securing top edge. Disconnect airbag harnesses, then remove rear seat back (Figure 4). Seat Belt Retainer 6. Pull rear door gasket away from body along rear pillar (Figure 5). 7. Pry up door scuff plate to release clips and remove (Figure 6). Continued on the next page. FIGURE 3 FIGURE 4 Door Gasket Door Scuff Plate FIGURE 5 FIGURE 6 11
12 Rear Deck Woofers (continued) 8. Pry off lower seat side trim to release clips. Pry off airbag harness clip, then remove trimpanel (Figure 7). 9. Pry off rear pillar trimpanel to release clips. Pull panel toward front of vehicle to remove (Figure 8). 10. Repeat steps 6-9 for the opposite side. 11. Disconnect third brake light harness (Figure 9). FIGURE 7 Lower Seat Side Trim FIGURE 10 Rear Deck Panel 12. Pry up rear deck panel to release four (4) clips. Pull panel toward front of vehicle and set panel down (Figure 10). Note: Seat belts remain in panel. Disconnect speaker wiring harness if vehicle is equipped with tweeters. 13. Remove four (4) 10mm screws securing speaker. Pull out speaker, disconnect and remove (Figure 11). 14. Secure new speaker to adaptor bracket. Place speaker/bracket assembly in location and mark new mounting holes. Remove assembly and drill holes with a 1/8 bit. 15. Connect speaker wiring adaptor of replacement speaker to vehicle speaker harness. Secure speaker/bracket assembly to location. 16. Connect airbag wiring harness and reconnect battery. 17. Test speaker operation and reassemble rear of vehicle by reversing removal steps. FIGURE 8 Rear Pillar Trimpanel FIGURE 9 Third Brake Light Harness SAFETY CHECK Make sure seats and seat belts are secured to manufacturer s specifications. Make sure brake light and airbag wiring harnesses are connected. FIGURE 11 Standard Speaker shown. JBL-Equipped speakers are mounted the same way. CAUTION: Always be careful when drilling or cutting in a vehicle. WEAR EYE PROTECTION. Be aware of things such as wiring, windows, fuel lines and safety devices. Check depth and location to avoid damage to vehicle appearance. 12
13 Rear Deck Tweeters NOTES: Please read first Instructions show factory size speakers or speakers with adaptor brackets only. Cutting or fabrication (not shown) will be required for other speaker sizes. IMPORTANT No speaker wiring adaptor is available at this time from Crutchfield for this speaker location. It will be necessary to splice wires in order to install an aftermarket speaker. No speaker adaptor bracket is available at this time for this location. A mounting bracket must be fabricated in order to install an aftermarket speaker. It is possible that the replacement speakers do not have screws supplied. It may be necessary to acquire mounting hardware. 1. Follow steps 1-12 on pages 11 and 12 to remove the rear deck panel. Return to this page to complete installation. 2. Remove three (3) phillips screws securing speaker/bracket assembly to bottom of rear deck panel. Lift assembly, disconnect and remove. 3. Fabricate a speaker mounting bracket and secure speaker to bracket. 4. Make wiring connections following instructions on page 14. Return to this page to complete installation. SAFETY CHECK 5. Secure speaker/bracket assembly to location. Make sure seats and seat belts are secured to manufacturer s specifications. Make sure brake light and airbag wiring harnesses are connected. 6. Connect airbag wiring harness and reconnect battery. 7. Test speaker operation and reassemble rear of vehicle by reversing removal steps. 13
14 Wire Splicing Guide These methods can be used to make wiring connections if no receiver or speaker wiring adaptor is available. CRIMP METHOD Factory harness is removed. Save harness if it is to be reconnected in the future by this method. SOLDER METHOD New speaker wires are spliced into factory wires behind harness. 1. Cut factory wires behind factory speaker harness. 2. Strip end of each wire back 1/2. 1. Carefully strip out a 1/2 section on each factory speaker wire behind the factory speaker harness. Factory Wires 2. Twist wires from new speaker to stripped sections of factory wires as shown making sure polarity is correct. Strip Out 1/2 Negative Wires New Wires Positive Wires Twist each positive pair of wires together and insert in crimp cap. Repeat step for negative wires. Factory Wire 4. Squeeze middle of cap for tight connection. 5. Connect new wires to speaker with spade connectors. 3. Heat wires first with soldering iron, then touch solder to wires for solid connections Last - - First Wrap wiring connections with electrical tape. 5. Connect new wires to speaker with spade connectors New Speaker Wire 14
* * Inside Ram. Tools Required 1500, 2500, 3500 IMPORTANT
Revision 10/07/14 IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call Crutchfield Technical Support
More information* * Ford Mustang. Tools Required. Inside...
evision 07/09/07 IMPOTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call Crutchfield at. Inside... TM
More informationIMPORTANT. Tools Needed: (depending upon vehicle) Phillips Screwdriver. Drill & Bit Set. Wire Stripper/ Crimp Tool
Revision 3/14/05 Amplifier Installation Guide IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call:
More informationMobile Video Installation Guide
000MVGUIDE Revision 04/29/04 Mobile Video Installation Guide This installation guide offers examples of mobile video system types and suggested layouts. The installation of your system will depend upon
More informationTOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
More informationTOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationToyota Avalon 2013-up HG
INSTALLATION INSTRUCTIONS FOR PART 95-8244HG KIT FEATURES Double DIN radio provision Painted high-gloss black APPLICATIONS Toyota Avalon 2013-up 95-8244HG Table of Contents Dash Disassembly Toyota Avalon
More informationINSTALLATION INSTRUCTIONS FOR PART
INSTALLATION INSTRUCTIONS FOR PART 99-7605 APPLICATIONS INFINITI G5 Coupe 2005-07 INFINITI G5 Sedan 2005-06 Painted And Finished To Match Factory Dash 99-7605 KIT FEATURES ISO Mount Radio Provision KIT
More informationCVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing
CVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 5/16 inch Socket Phillips Screwdriver 1/2 inch
More informationScion xa SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS
More informationToyota 4RUNNER With/MR Overhead Video
Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:
More informationSCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT
Section I Installation Preparation Part Number: PT900-52080 Kit Contents Item # Quantity Reqd. Description 1 2 DVD Headrest Unit 2 2 Headrest Extension Cables 3 1 Audio Interface Module 4 1 Audio Interface
More informationSCION XB SUBWOOFER ENCLOSURE Preparation
Preparation Part Number: Kit Contents Item # Quantity Reqd. Description 1 1 Subwoofer enclosure 2 1 Wire Harness 3 1 Paper Template 4 1 Plastic Drill Template 5 1 Hardware Bag Hardware Bag Contents 1 Item
More informationConflicts: Vehicles without a sunroof Vehicles with a single sunroof
Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles
More informationConflicts: Vehicles with a sunroof
Toyota 4Runner Non/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit -00110-15, Beige 00016-00120; Fit Kit -00120-15, Gray Accessory Code: ED6 Conflicts: Vehicles with a sunroof Kit Contents:
More informationToyota RAV up
REV. 2/27/2014 INST99-8217 INSTALLATION INSTRUCTIONS FOR PART 99-8217 APPLICATIONS See application list inside Toyota RAV 4 2006-up 99-8217 KIT FEATURES DIN radio provision with pocket ISO DIN radio provision
More informationSCION xa AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-52040 (Compass) PT374-21050 (Homelink) Kit Contents Item # Quantity Reqd. Description 1a 1 AD Mirror Assembly w/compass & Map Lights (P/N PT374-52040) 1b 1 AD Mirror Assembly
More informationIf technical support is required, please contact Advent Technical Support at
Document 128-9015A Created 12/12/11 Kit Contents: Item # Qty. Component Description 1 2 Headrest Assembly 2 2 Cables # 3 3 1 Power Cord # 9 4 1 FM Antenna 5 1 Control Box 6 2 IR Headphones 7 2 Remote Control
More informationTOYOTA TACOMA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,
More informationTOYOTA Matrix XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-12080 Tuner Assembly 86180-0W031 (Music Only) Tuner Assembly PT546-00090 (Music Plus Data) NOTE: Part number of this accessory may not be the same as the part
More informationFor additional technical tips, please visit
NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH IS NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE
More informationPush Start Ignition (05-10 All) Installation
Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10
More informationSTREET SCENE EQUIPMENT,INC. CONNECTING STREET SCENE SIGNAL MIRRORS
STREET SCENE EQUIPMENT,INC. CONNECTING 365 McCormick Avenue STREET SCENE SIGNAL MIRRORS Phone (714) 426-0590 Fax (714) 426-0591 1993-2001 CONNECTING STREET SCENE SIGNAL MIRRORS INSTRUCTIONS FOR PART NUMBERS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 31716 HONDA (For ipod ) FIT Issue Date MAR 2006 PARTS LIST Attachment Kit P/N 08A28-1H1-800 4 Cushion tapes Honda Music Link Kit P/N
More informationPart Number: PT
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationCERTAIN TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE
PAGE 1 OF 19 CERTAIN 2015-2017 TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE OVERVIEW In the affected vehicles, it may be possible for water to pool and
More informationSCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationM GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET
Please contact the Ford Racing Techline for the most current instruction information @ (800) FORD-788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following
More informationTOYOTA LAND CRUISER 2003 DVD VES
LEXUS LX470 Section I Installation Preparation Part Number: PT296 6002D 03/16 (LC) PT296 6002L 03/16 (LX) Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 FPD Assembly
More informationMustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC #
1990-1993 Mustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC # 101000 Kit Components: 1 Light Bar 4 Bolts ( 5 / 16-18 x 2.5 ) #182010 4 Washer #182005 4 Shims #182009 2 Dark Blue Connectors #182004
More informationFor additional technical tips, please visit
NOTICE OF INTENDED INSTALLATION AND USE THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH IS NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE
More informationConflicts: Vehicles with no sunroof or dual sunroof
Toyota Sienna (Single Sunroof) 2012-8.5 Overhead Video Part Number: 00016-00125 -11 Accessory Code: ED9 Conflicts: Vehicles with no sunroof or dual sunroof General Applicability: 2011 Sienna SMR Kit Contents:
More informationTOYOTA SIENNA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit: PT546-08070 Tuner Assy: 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting Kit Contents
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationSCION xb AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Mazda TOOLS REQUIRED:
INSTALLATION INSTRUCTIONS FOR PART 99-7504 APPLICATIONS Mazda 3 2004-2008 99-7504 KIT FEATURES DIN Mount Radio Provision with Pocket ISO Mount Radio Provision with Pocket onus Display Replacement Pocket
More informationSCION xb SIRIUS SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS3-52050 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description Antenna, Exterior 2 Wire Harness 3 Bracket,
More informationTOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Mazda For Models With Manual Climate Controls TOOLS REQUIRED:
INSTALLATION INSTRUCTIONS FOR PART 99-7509 APPLICATIONS Mazda 5 2006-2007 For Models With Manual Climate Controls 99-7509 KIT FEATURES Painted To Match Factory Dash DIN Radio Provision with Pocket ISO
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationMazda S
INSTALLATION INSTRUCTIONS FOR PART 99-7523S KIT FEATURES Double DIN radio provision ISO DIN radio provision with pocket Painted silver Pre-wired ASWC-1 harness included (ASWC-1 sold separately) APPLICATIONS
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 12035 SYSTEM 2012 RIDGELINE Issue Date NOV 2011 PARTS LIST Security System Attachment Kit: P/N 08E55-SJC-101 Flange bolt Unit bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26042-26353 XM INTERFACE ODYSSEY EXCEPT EX-L WITH NAVI/RES Issue Date FEB 2004 PARTS LIST 8 Wire ties XM Radio Attachment P/N 08B15-S0X-100
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ATTACHMENT (EX-L WITH NAVI) 2008 RIDGELINE AII 36587 Issue Date MAY 2007 PARTS LIST Attachment Kit P/N: 08B21-SJC-102 Template Rear camera
More informationTape the screwdriver tip before use. Using a screwdriver, remove the inside handle bezel.
Page 1 of 16 DISASSEMBLY 1. REMOVE DOOR INSIDE HANDLE BEZEL a. Using a screwdriver, open the cap. Tape the screwdriver tip before use. b. c. Remove the screw. Using a screwdriver, remove the inside handle
More informationTOYOTA im NAVIGATION UPGRADE Preparation
Preparation Part Number: PT296-00170 PT296-12170 (Extension Module w/ AHA) Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna kit 5 6 Bolt
More informationSCION FR-S FOG LIGHTS
Part #: PT413-18130 Conflicts: Lowering Springs PTR07-18130-LL (California only) Kit Contents: For Anniversary Edition, Monogram & RS 2.0 vehicles, additional parts need to be ordered (PT413-18130-LL)
More informationNissan Sentra (without pocket door)
INSTALLATION INSTRUCTIONS FOR PART 99-7422 APPLICATIONS See application list inside Nissan Sentra 2007-2012 (without pocket door) 99-7422 KIT FEATURES DIN radio provision with pocket Double DIN radio provision
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW REGULATOR (742-269) Ford Mustang 1996 2004 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CD CHANGER ATTACHMENT KIT 2005 CIVIC SI AII 27936 Issue Date AUG 2004 PARTS LIST CD Changer Attachment Kit (sold separately): P/N 08B26-S5T-100
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 22903-22963 ODYSSEY Issue Date MAY 2002 PARTS LIST Subwoofer Kit: P/N 08A39-EP7-100 Subwoofer 2 Cushion tapes 8 Wire ties (1 not used)
More informationXM Adapter Cable (P/N: ) MUST be used for this vehicle.
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 XM Adapter Cable (P/N: 00016-00076-10) MUST be used for this vehicle. Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description
More informationSCION xb EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24642 BODY SIDE CLADDING 2003 CR-V P/N 08P21-S9A-100 Issue Date OCT 2002 PARTS LIST Right rear bumper piece Right front fender piece
More informationTOYOTA COROLLA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationTOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)
Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting
More informationLEXUS CT 200h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-89100 Kit Contents Item # Quantity Req'd. Description 1 1 Door Sill, Front Right Hand 2 1 Door Sill, Front Left Hand 3 1 Door Sill, Rear Right Hand 4 1 Door Sill, Rear Left
More informationI-Sheet Number Rev.B 3-1/2 OVAL BULL BAR DODGE RAM 1500
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 2563000 Parts List 1 Carrier weldment 2 Support arm assembly 1 Third brake light assembly 1 Light extension bracket 1 Spare tire adjustment plate 1 Spare tire mount plate 1 Female spade
More informationTHE safety accessory of the 21 st Century.
00 006 Chevrolet SSR Signal Mirror Installation Instructions THE safety accessory of the st Century. Note: Professional Installation Recommended Warranty does not cover damage to the vehicle or mirror
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationSCION im PREMIUM AUDIO Preparation
SCION im 2016 - PREMIUM AU Preparation Part Number: PT296-12160 (Extension Module w/ AHA) Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna
More informationPART NUMBER: H630SXC001. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4)
Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) E. Clip B. Interface / Power Harness (1) C. Cable tie (8) F. Mounting Nuts (2) G. Replacement Front Speaker (2) H. Badge mounting
More informationTOYOTA RAV INTERFACE KIT FOR IPOD Preparation Part Number: PT
Preparation Part Number: PT545-00082 NOTE: Part number of this accessory may not be the same as the part number shown. General Applicability Note: Kit Contents Item # Quantity Reqd. Description 1 1 Unit
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS Lexus ES Series
INSTLLTION INSTRUCTIONS FOR PRT 99-855 PPLICTIONS 997-00 Lexus ES Series 99-855 KIT FETURES DIN Head Unit Provision with Pocket ISO DIN Head Unit Provision with Pocket KIT COMPONENTS ( ) Radio Housing
More informationConflicts: Highlander without sunroof
Toyota Highlander (Sunroof) 2011-8.5 Overhead Video Part Number: 00016-00125; Fit Kit-00016-00125-02 Accessory Code: ED9 Conflicts: Highlander without sunroof Kit Contents: Item # Qty. Component Description
More informationINSTALLATION INSTRUCTIONS
Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8838) Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions Required Tools & Supplies
More informationTOYOTA CAMRY EC REARVIEW MIRROR Preparation
TOYOTA CAMRY 2010 - EC REARVIEW MIRROR Preparation Part Number: 00016-09101 Code: CM9 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ Compass 2 1 Hardware bag Hardware Bag Contents
More informationTOYOTA VENZA HANDS FREE BLU LOGIC Preparation
TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationScion xb EC Rearview Mirror w/ Shift Light Preparation
2008 - Preparation Part Number: 00016-79800 Accessory Code: YM10 Kit Contents Item # Quantity Reqd. Description 1 1 Mirror Assembly w/ PRNDL 2 1 Hardware bag 3 1 Installation Manual Hardware Bag Contents
More informationPART NUMBER: H630SSJ000. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4)
Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) E. Clip B. Harness (1) C. Cable tie (8) F. Mounting Hardware (2) G. Replacement Speaker (2) H. HVAC Duct extension (2) IMPORTANT:
More informationTOYOTA 4 RUNNER 2010-UP
INSTALLATION INSTRUCTIONS FOR PART 99-8227S KIT FEATURES KIT COMPONENTS APPLICATIONS TOYOTA 4 RUNNER 2010-UP U.S. PATENT # D639,292 99-8227S DIN Head unit provisions with pocket ISO DIN Head unit provision
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE ENGINE STARTER SYSTEM Application 2010 CIVIC 4-DOOR Publications No. AII 42460 Issue Date AUG 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B
More informationHonda Accord (Equipped with Single Zone Climate Controls)
INSTLLTION INSTRUCTIONS FOR PRT 99-7864 PPLICTIONS Honda ccord 2003-2007 (Equipped with Single Zone Climate Controls) 99-7864 KIT FETURES DIN Radio Provision ISO Radio Provision KIT COMPONENTS ) Radio/Climate
More informationGentex by VOXX Corporation Installation Instructions
KIT CONTENTS: Item Qty Part Number Description 1 1: ADVGEN20A 7 Pin Auto-Dimming Mirror with Compass and Temperature 2 1 Gentex by VOXX Corporation Installation Instructions Contact VOXX Customer Service
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM ACCORD 2-DOOR (LX/EX L4, LX V6) AII 25749 Issue Date FEB 2004 PARTS LIST Double-sided adhesive tape XM Radio Attachment Kit : P/N
More informationTOYOTA TUNDRA TVIP V4 Preparation
Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. Remote Engine Starter Attachment Kit P/N 08E92-SNA-100B
INSTALLATION INSTRUCTIONS Accessory Application Publications No. REMOTE ENGINE STARTER SYSTEM 2008 CIVIC 2-DOOR AII 38215 Issue Date OCT 2007 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B
More informationHonda Civic
Installation instructions for part 99-7816 KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted to match factory dash: 99-7816G = Gunmetal, 99-7816T= Taupe Honda Civic 2006-2011
More informationTOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford F-250 to F-750 Pick-Up, Super-Duty 1998-2007 Trailer Tow Mirror Ford Excursion XLT/Limited 2000-2002 Trailer Tow Mirror Ford Excursion (all models) 2003-2005
More informationConflicts TOYOTA TACOMA HANDS FREE BLU TOOTH. Part Number: Accessory Code: BT4 ADDITIONAL ITEMS REQUIRED FOR INSTALL
TOYOTA TACOMA 2011 - HANDS FREE BLU TOOTH Part Number: 00016-00401 Accessory Code: BT4 Conflicts Factory Bluetooth System & JBL Audio KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE MODULE 2 1 INTERFACE
More informationLEXUS LC/LCh CARBON FIBER LOWER GRILLE Preparation
Preparation Part Number: PT478-11175-05 Kit Contents Item # Quantity Reqd. Description 1 1 Carbon Fiber Lower Grille Insert 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 2 3 Additional
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 32459-34084 XM RADIO SYSTEM 2007 RIDGELINE Issue Date NOV 2006 PARTS LIST 4 Washer-screws, 5 x 8 mm Attachment Kit: P/N 08B15-SJC-100A
More informationShelby GT500 Front Fascia Conversion Kit (05-09 All) Item # Installation Time: 1 Day. Required tools:
Shelby GT500 Front Fascia Conversion Kit (05-09 All) Item #53611 Installation Time: 1 Day Required tools: Phillips Screw driver 10mm Socket + Ratchet/Wrench 8mm Socket + Ratchet/Wrench 5mm Socket + Ratchet/Wrench
More informationGeneral Applicability: Toyota Sienna. Issues Updated CAN wire location and attachment
Document #730145 Created ACH 10/19/2018 Revised ACH 10/26/18 A2 General Applicability: 2018-19 Toyota Sienna Issues Updated CAN wire location and attachment Kit Contents: Item# Component Description 1
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26031 2004 ODYSSEY Issue Date AUG 2003 NOTE: You cannot install the subwoofer in a vehicle equipped with both an under seat Navigation
More informationSCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationINSTALLATION INSTRUCTIONS FOR PART APPLICATIONS. Mercedes C-Class Mercedes CLK 2004 TOOLS REQUIRED:
INSTLLTION INSTRUCTIONS FOR PRT 99-870 PPLICTIONS Mercedes C-Class 200-2004 Mercedes CLK 2004 99-870 KIT FETURES DIN Radio Provision with Pocket KIT COMPONENTS ) Radio Housing TOOLS REQUIRED: Small Flat
More informationTOOLS REQUIRED: Panel Removal Tool Phillips Screwdriver 10mm Nut Driver Ratchet 10mm Socket 7mm Wrench 7mm Nut Driver Straight Screwdriver
CONTENTS: 1EA. FIVE CHANNEL AMPLIFIER/BRACKET ASSEMBLY P/N MPDSP039AA 1EA. OVERLAY HARNESS P/N RH41LX10 3EA. 7MM SCREWS P/N RF7MM 6EA. WIRE TIE P/N RFZIP6 1EA. 30 AMP FUSE P/N RFUSE30 1EA. INSTRUCTIONS
More informationTOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Honda Dealer: Please give a copy of these instructions to your customer. PARTS LIST (15) (8) (12) (14) (13) (10) (11) (18) (17) (1) Accessory Application Publications No. TRX500FA/FGA
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More information