LOGAN. Installation manual: Parrot MKi + Parrot CK3100 range LOGAN

Transcription

1 Installation manual: Parrot MKi + Parrot CK3100 range LOGAN This The brand sheet name is designed DACIA LOGAN to help and you the with DACIA the installation logo are the of property a Parrot of product DACIA. and is purely for information. Any installation performed in compliance This document with is the only instructions valid for the appearing vehicle model in this LOGAN document year is 2008 done to under 2011, the excluding sole responsibility all other models of the in installer, the same who range is entirely and excluding responsible later for modifications the quality made of the to installation. the vehicle All by rights the manufacturer. reserved Copyright 2011 PARROT SA RCS PARIS May not be reproduced without the authorisation The Parrot brand of Parrot name SA. and Pictures logos are for the information exclusive property only. of Parrot SA.

2 Fitting time (estimated) / Main features Disassembly 15min YES +IGN Mounting kit 20min YES ISO Reassembly 15min N/A UNIKA Testing 15min FRONT LOUDSPEAKER TEL mode Total 1h 05min ALL MUSIC mode Tools Plastic trim removal tools FACOM / BOJO -Multimeter or Test lamp - Wire tie -Electrical tape FACOM DX-25 kit (n 4 tools) Accessories required "Please contact your wholesaler to purchase accessories. A list of wholesalers is available at " Updating To get the most out of your hands-free kit we recommend that you update your software regularly. The update procedure can be found at

3 Disassembly

4 Disassembly Insert the removal tools into the slots on each side of the radio. Unclip the radio, pull it out and unplug the connectors and the antenna then remove the radio. 4 Using the plastic trim removal tools, unclip the car stereo and air conditioning surround starting at the bottom and moving towards the top. Remove the passenger side door seal.

5 Microphone passage 1 2 Glue the bracket (supplied) to the windscreen, after having thoroughly degreased the surface. 3 Run the cable under the headliner to the passenger side support. 4 Run the cable along the passenger side windshield support while replacing the door seal. 5 Then pass the cable under the dashboard on the bottom of the glove box. To finish, run it to the radio housing.

6 Feeding the accessory cable 1 2 In the bottom of the glove box, insert the cable into the hole next to the DIAG socket. Then bring it out into the radio housing, taking care to leave enough length.

7 Fitting the hands-free system 1 / 2 1 On the kit connector (supplied), reverse the fuses (i.e. swap the red and orange wires) and connect all the cables to the blue box as shown in the diagram below. Test everything before reassembling... ISO adapter 2...then store the box under the radio housing.

8 Fitting the hands-free system 2 / 2 3 4! Glue the bracket (supplied) under the cover of the central console between the air vents, after carefully degreasing the surface. Pass the cable into the air conditioning housing while clipping the console cover (TAKE CARE to avoid cutting the screen cable). 5 Re-clip the assembly and insert the screen.

9 Testing Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob of the remote control, check: 1 - that the menu is displayed on the screen (language or ipod etc) 2 - that the radio system is muted when the kit is in use (click in the blue box) 3 - that the sound through all speakers is properly muted 4 - that there is sound through the front speakers for spoken menus 5 - then turn off the ignition, verify that the kit turns off and that the message goodbye is displayed on the screen (otherwise reverse the fuses on the kit power supply harness) 6 - pair a telephone with the kit and make a call (check that both the microphone and the kit are working)

10 Reassembly Refit the system using the following procedure: 1 - reconnect the connectors and the antenna to the radio and slide it into its housing.