Saving you Time, Saving you Money, Putting you First! CENTER HUNG TRAY. Width Length in Inches

Transcription

1 INTRODUCTION For an integrated wire management system, Center Hung Tray simplifies the support and routing of power and telecom/teledata cabling. single hanger rod is used at each support point. This makes installation easier by reducing support requirements and eliminating the need to pull cable through the trapeze supports. Center Hung provides substantial savings in cost and time. With Center Hung Tray, cables can be laid in on both sides. Both the support and connection of the Center Hung Tray sections are accomplished by a single splice coupling designed to save time. If additional support is needed beyond the 10 feet or 3 meter intervals, an intermediate support hanger can be used. Easy step 1, 2, 3 connections for fast and effective site installation: Step 1 - insert rod in splice Step 2 - connect center section to splice Center Hung Tray rungs come already attached transversely through either the top or bottom of the center tubular rail. Each rung is securely staked to the center rail in four places, providing additional strength and rigidity for reliable cable support. The chances for damaging and losing rungs during transportation and cable installation are significantly reduced with this safe, reliable and secure method of rung attachment. TECHNICL DT 6 to 24 inches. Length 10 feet (120 ) standard. Fill 3, 4 and 6 inches. Rung Spacing 3, 6, 9, 12 and 18 inches. Materials luminum lloy 6061-T6, 6063-T6. Step 3 - slide together CTLOG NUMBER 1 2 L Material Style: Rung Space Style (Prefix) Length in Inches T = Center Hung Top Mount Rung WT = Wall Mount Top Rung Single Tier L = Center Hung Bottom Mount Rung WL = Wall Mount Bottom Rung Single Tier page 27

2 DIMENSIONS Top Rung Bottom Rung Load 1/2" Load 1/2" 1 1/2" 1 1/2" Overall Height Top TYPES OF CENTER HUNG Overall Height Bottom Top Load Bottom TOP CENTER HUNG BOTTOM CENTER HUNG DUL CENTER HUNG Unique dual width rungs provide 4 separate cable compartments without dividers. Dual width rung catalog numbers utilize our standard format, except both widths are shown. WLL RCK Three 3/4 wall spacers that are provided with each standard 10 or 3m section must be mounted between back of spine and wall at mounting points. This unique design permits a wall rack to be installed without the use of a wall bracket. page 28

3 CENTER HUNG FITTINGS ND CONNECTORS HORIZONTL TEE/90 CONNECTOR HORIZONTL CROSS COUPLING Horizontal Tee/90 Connector Bottom Rung Top Rung 6 SP-TL-3 SP-TT-3 9 SP-TL-4 SP-TT-4 12 SP-TL-6 SP-TT-6 18 SP-TL-9 SP-TT-9 24 SP-TL-12 SP-TT-12 VERTICL TEE/90 CONNECTOR (SP-VT) Horizontal Cross Coupling Bottom Rung Top Rung 6 SP-XL-3 SP-XT-3 9 SP-XL-4 SP-XT-4 12 SP-XL-6 SP-XT-6 18 SP-XL-9 SP-XT-9 24 SP-XL-12 SP-XT-12 SPLICE CONNECTOR (SP-CR-B) OFFSET VERTICL CONNECTOR (SP-VOFF-3) VERTICL HINGE CONNECTOR (FS-VCR) HORIZONTL HINGE CONNECTOR (FS-HCR) page 29

4 CCESSORIES BOX CONNECTOR Catalog Number: B C ( ) W D (W): 3,, 9, 12, 18, 24 (D): 3, 4, BRRIER STRIP 3 4 3S-144-CR 4S-144-CR 6S-144-CR For mounting to equipment and wall entrance flanges. WLL BRCKET Rugged construction together with the ability to hang tray without any special clamps makes this bracket an efficient and economical device. Fixing Clamps and Screws included. WLL MOUNT Catalog Number: SP-WLL Tray WBK-6 WBK-7 WBK-9 WBK-12 WBK-15 CBLE DROP OUT This connector allows for a sturdy connection for short wall-to-wall runs. Drop Out VD-3-CR VD-4 -CR VD-6-CR VD-8 -CR Drop Out VD-9-CR VD-11 -CR VD-12-CR RUNG CP Rung caps are used for system identification. Option RUNG CP Option B ttaches to rung with hardware provided. Color Red Black Blue Orange Catalog No. RCP Red RCP Black RCP Blue RCP Orange page 30

5 RIL END CP Catalog Number: E P - C R Simplified one nut and bolt installation to close up end of spline. BLIND END Catalog Number: E P ( ) - W - D Simple one nut and bolt installation. Please advise width and rung type (top/bottom) when ordering. CENTER HUNG COVERS Cover ttachment Illustration Cover ( ) For Cable Tray Please insert T for Top Rung and L for Bottom Rung. ( ) For Wall Rack Please insert TR for Top Right Hand, TL for Top Left Hand, LR for Lower Right Hand and LL for Lower Left Hand. Center Hung Cover Insert SOLID TOP COVER Technical Data : to 24 Length: 10 feet (120 ) standard Catalog Number For top mounted rung: CCTF-W-120 For bottom mounted rung: CCLF-W-120 SOLID BOTTOM INSERT Technical Data : to 24 Length: 10 feet (120 ) standard Catalog Number For top mounted rung: ST-W-D-120 For bottom mounted rung: SL-W-D-120 Notch permits cover to slide between the support nut and washers for secure attachment Notch permits cover to slip under washer & nut for easy hold down Note: Includes one sheet metal connector per insert. D W. page 31