HP5 BULL PIN FOR FRAME LINE APPLICATIONS 754 LBF RETRACT 60 PSI
|
|
- Arlene McKinney
- 5 years ago
- Views:
Transcription
1 ISO 9001 REGISTERED HP5 BULL PIN FOR FRAME LINE APPLICATIONS 754 LBF RETRACT 60 PSI RETRACTING LOCATING PIN WITH A 2KG SLIDE HAMMER PISTON. RAP ACTION* PROVIDES CONCENTRATED PULLING POWER. A GREATER THAN FOUR TIMES SHAFT DIAMETER TO BEARING LENGTH RATIO IS ALWAYS FULLY ENGAGED, OFFERING LONG PRECISION LIFE. NO MAINTENANCE OR GREASING REQUIRED. (*RAP ACTION ON PNEUMATIC UNIT ONLY) PNEUMATIC CYLINDER SAFETY BLUE POWDER COAT FINISH SOLID STATE CYLINDER SWITCH OR WORLD SWITCH ANTI-ROTATE FEATURE IS COMPLETELY SEALED FROM CONTAMINATION. ALLOWS MOUNTING OF 2-WAY PINS AND CROWDER PADS CHROME-PLATED SHAFT WITH HIGH-LOAD PTFE COMPOSITE BEARINGS. SHAFT IS 100% CONTINUOUSLY ENGAGED IN BEARINGS URETHANE SCRAPER KEEPS OUT WELD SPATTER HYDRAULIC CYLINDER ONLY AVAILABLE WITH WORLD SWITCH STANDARD UNIT INCLUDES SHIM SET & GRIND SPACER OPTIONAL MOUNTING PAD FOR HORIZONTAL & VERTICAL SHIM ADJUSTMENT. MOUNTING PAD SHOWN IN POSITION 2 (OPTION M2) MOUNTING PAD SHOWN IN POSITION 4 (OPTION M4) RELEASED 2/2/17 Welker Engineered Products 1401 Piedmont Troy, MI
2 APPLICATION GUIDE HP5 Bull Pins are made for inline balanced loads. There is an anti-rotate feature but it is for orientation only - not for offset loads. GOOD APPLICATIONS (VIEWS ARE FROM PIN END, HP5 SHOWN) ROUND PIN DIAMOND PIN PUSHER BLOCK PIN/PUSHER BLOCK COMBO BAD APPLICATIONS FOR HP5, GOOD APPLICATIONS FOR WP6 SHOT PINS (VIEWS ARE FROM PIN END, WP6 SHOWN) OFFSET PIN PIN WITH OFFSET PUSHER BLOCK PUSHER BLOCK WITH OFFSET PIN DOUBLE PIN SHEET 2
3 ORDERING INFORMATION NOTE: ALL BOXES MUST BE FILLED IN FOR A COMPLETE PART NUMBER H P Cylinder P Pneumatic H Hydraulic Port Position 1 Position 1 2 Position 2 3 Position 3 4 Position 4 Mounting Assembly 00 None M2 Mounting Position 2 M4 Mounting Position 4 Switch Option 00 None VE World Switch L3 Cylinder Switch (Pneumatic Option only) Welker Cylinder Switch Chart Option Switch Part # Mfr L3 SWITCH L3 Welker L3 switch is weld field immune, comparable to World Switches. Switch is 4-wire, 4-pin, DC M12 x 1 (PNP) Quick Disconnect Order Number SO1 EXTEND (E) or SO1 RETRACT (R) Part Num ber Manufacturer Description 00 NONE World Switch VE or VR NBN2-F S6-E8-V1 Pepperl & Fuchs 3-Wire, 4-Pin, DC M12 X 1 (PNP) Quick Disconnect SHEET 3
4 571.2 RETURNED EXTENDED GENERAL DIMENSIONS HYDRAULIC CYLINDER HYDRAULIC CYLINDER: 2" BORE X 97mm [3.818] STROKE, 1400 PSI MAX CUSHIONS BOTH ENDS #6 SAE PORTS FLUOROCARBON SEALS FOR PISTON AND ROD HIGH LOAD PISTON WORLD SWITCH OPTION ONLY PNEUMATIC CYLINDER: 4" BORE X 100mm STROKE LESS 3.0mm FOR RAP 97.0mm ACTUAL STROKE 1/2" NPT PORTS 11.0 SLOT TYP n10.00 S.F. THRU (2) PLACES RETURNED EXTENDED n6.35 DRILL THRU FOR THIS VIEW'S DIMENSIONS SEE SHEET 5 A A 8.36 PNEUMATIC CYLINDER SOLID STATE CYLINDER SWITCH (SHOWN) OR WORLD SWITCH SHIM/SPACER INCLUDED M10x1.5 TAP x 20.0 (2) PLACES NEARSIDE, (2) PLACES FARSIDE IN LINE M6x1 TAP x (2) PLACES KEYWAY x6.00 KEYWAY x 6.00 KEYWAY CUSTOMER TO SUPPLY KEYS REF REF SECTION A-A SHEET 4
5 GENERAL DIMENSIONS: HP5 NOSE END VIEW M5x0.8 TAP x 10.0 (4) PLACES IN HOUSING 3 M8x1.25 TAP x n x M5x0.8 TAP x 15.0 (4) PLACES IN RAM n4.0 S.F. x 8.0 SHEET 5
6 MOUNTING OPTION DIMENSIONS HP5 WITH MOUNTING ASSEMBLY OPTION M2: SHOWN WITH HYDRAULIC CYLINDER n10.00 S.F. THRU (2) PLACES n10.50 DRILL THRU (4) PLACES WELDED ON BOTH ENDS & STITCH WELDED ON LENGTH OF RETAINER BOTH SIDES (NO WELD IN CENTER ON INNER FACE) M4 MOUNT SHIM/SPACER SHIM/SPACER HP5 WITH MOUNTING ASSEMBLY OPTION M4: SHOWN WITH PNEUMATIC CYLINDER M2 MOUNT KEY INCLUDED WITH MOUNTING OPTION FOR CUSTOMER USE ON OPPOSING MOUNTING DETAIL x 6.00 KEYWAY KEYWAY THRU SHEET 6
UB4 SERIES GOLD LINE SHOT PIN
ISO 9001 REGISTERED UB4 SERIES GOLD LINE SHOT PIN NPT or G PORTS INTEGRATED CYLINDER INTEGRATED WORLD SWITCH LIGHTWEIGHT ALUMINUM BODY RAP OR RIGID COUPLER CORROSION & WELD SPATTER RESISTANT STEEL RAM.
More informationUB2 SERIES GOLD LINE SHOT PIN
ISO 9001 REGISTERED UB2 SERIES GOLD LINE SHOT PIN NO LUBRICATION REQUIRED NPT OR G PORTS INTEGRATED CYLINDER SHROUD SOLID STATE CYLINDER SWITCH OR WORLD SWITCH NAAMS STANDARD MOUNTING RAP OR RIGID COUPLER
More informationGROUND BLOCK RETRACT CYLINDERS
ISO 9001 REGISTERED GROUND BLOCK RETRACT CYLINDERS FOR ALL MIG & ARC WELDING APPLICATIONS IN FIXTURES, TRUNIONS, AND DIAL TABLES. INSULATED GROUND BLOCK CYLINDERS ARE IDEAL FOR SINGLE-POINT WELDING. SOLID
More informationDB4 GUIDED SLIDE APPLICATIONS: ISO 9001 REGISTERED RETRACTABLE PINS & LOCATORS PUSHERS CROWDERS THRUSTERS SMALL LIFTERS SLIDES
ISO 9001 REGISTERED DB4 GUIDED SLIDE 1/4" NPT or G1/4 PORTS RAP OR RIGID COUPLER TOOL MOUNTING SURFACE WELKER 70mm BORE PNEUMATIC CYLINDER SOLID STATE CYLINDER SWITCH NAAMS STOPS OR WELKER SMART STOPS
More informationUPE/SPE SERIES PART EJECTOR ONE ACTUATOR TO LIFT AND TIP TO EJECT
ISO 9001 REGISTERED UPE/SPE SERIES PART EJECTOR ONE ACTUATOR TO LIFT AND TIP TO EJECT OPTIONAL TIP ANGLES 11, 22, 31, 39, 45 TREATED STEEL TIP PLATE WITH TAPPED HOLES/DOWELS & KEY FOR TOOLING WORLD SWITCH
More informationUB4 SERIES GOLD LINE SHOT PIN
ISO 9001 REGISTERED UB4 SERIES GOLD LINE SHOT PIN NPT or G PORTS INTEGRATED PNEUMATIC CYLINDER INTEGRATED WORLD SWITCH LIGHTWEIGHT ALUMINUM BODY SHROUD RAP OR RIGID COUPLER CORROSION & WELD SPATTER RESISTANT
More informationUB4 SERIES GOLD LINE SHOT PIN
ISO 9001 REGISTERED UB4 SERIES GOLD LINE SHOT PIN NPT or G PORTS* INTEGRATED PNEUMATIC CYLINDER INTEGRATED WORLD SWITCH* WITH SWITCH GUARD LIGHTWEIGHT ALUMINUM BODY SHROUD* RAP OR RIGID COUPLER* CORROSION
More informationLST SERIES PART POSITIONER
ISO 9001 REGISTERED LST SERIES PART POSITIONER ONE ACTUATOR TO ETEND AND TIP TOOLING AWAY REPEATABLE RETRACTED POSITION CHOICE OF TIP ANGLES* 11, 22, 31, 39, 45 TREATED STEEL TIP PLATE WITH TAPPED HOLES/DOWELS
More informationLOW PROFILE RAIL SLIDES
ISO 9001 REGISTERED LOW PROFILE RAIL SLIDES NL3 100mm BORE STANDARD MOUNTING FOR TOOLING (TAPS AND DOWELS) WELD SPATTER RESISTANT ALUMINIZED KEVLAR RAIL SHROUDS SHOCKS 425mm 350mm 760mm + STROKE - 100mm
More informationMPE PART EJECTOR MST PART POSITIONER
PART EJECTOR PART POSITIONER ISO 9001 REGISTERED CAM ACTION LIFTS UP TIP PLATE 30mm AND TIPS OUT 30 CAM ACTION ROTATES TIP PLATE 30 THEN CLAMPS DOWN VERTICALLY 25mm NAAMS STANDARD TAPPED/DOWEL HOLES TO
More informationUPE/SPE SERIES PART EJECTOR ONE ACTUATOR TO LIFT AND TIP TO EJECT
ISO 9001 REGISTERED UPE/SPE SERIES PART EJECTOR ONE ACTUATOR TO LIFT AND TIP TO EJECT OPTIONAL TIP ANGLES 11, 22, 31, 39, 45 TREATED STEEL TIP PLATE WITH TAPPED HOLES/DOWELS & KEY FOR TOOLING WORLD SWITCH
More informationSB4 & SB6 SERIES GOLD LINE SIDE-BY-SIDE SHOT PINS
ISO 9001 REGISTERED SB4 & SB6 SERIES GOLD LINE SIDE-BY-SIDE SHOT PINS CORROSION & WELD SPATTER RESISTANT MOUNTING FOR CYLINDICATOR STYLE PROX SWITCHES NAAMS STANDARD MOUNTING NPT or G PORTS LIGHTWEIGHT
More informationSST SERIES PART POSITIONER
ISO 9001 REGISTERED SST SERIES PART POSITIONER ONE ACTUATOR TO ETEND AND TIP TOOLING AWAY REPEATABLE RETRACTED POSITION TREATED STEEL TIP PLATE WITH TAPPED HOLES/DOWELS & KEY FOR TOOLING 30 TIP ANGLE BASE
More informationSTROKES: 025, 050, 075, 100, 125, 150, 175, 200mm PNEUMATIC OR HYDRAULIC CYLINDER LIGHTWEIGHT ALUMINUM BODY
ISO 9001 REGISTERE WP4 & 6 SERIES GOL LINE STROKES: 025, 050, 075, 100, 125, 150, 175, 200mm PNEUMATIC OR HYRAULIC CYLINER SHOT PINS WP4 40mm SQUARE RAM SOLI STATE CYLINER SWITCH AVAILALE WITH WP4 70mm
More informationSB4 & SB6 SERIES GOLD LINE SIDE-BY-SIDE SHOT PINS
ISO 9001 REGISTERE SB4 & SB6 SERIES GOL LINE SIE-BY-SIE SHOT PINS CORROSION & WEL SPATTER RESISTANT RAM MOUNTING FOR CYLINICATOR STYLE SWITCHES (NOT INCLUE) NAAMS STANAR MOUNTING NPT or G S LIGHTWEIGHT
More informationMAINTENANCE MANUAL UB SERIES SHOT PINS
ENGINEERED PRODUCTS ISO 9001 REGISTERED MAINTENANCE MANUAL UB SERIES SHOT PINS UB4 WORLD SWITCH & SWITCH GUARD WELKER PNEUMATIC TIE ROD CYLINDER UB2 STEEL SOLID STATE CYLINDER SWITCH WELKER PNEUMATIC COMPACT
More informationMAINTENANCE MANUAL UB SERIES SHOT PINS
ENGINEERED PRODUCTS ISO 9001 REGISTERED MAINTENANCE MANUAL UB SERIES SHOT PINS UB4 WORLD SWITCH WELKER PNEUMATIC TIE ROD CYLINDER UB2 STEEL SOLID STATE CYLINDER SWITCH WELKER PNEUMATIC COMPACT CYLINDER
More informationXPC PIN CLAMPS & XFC HOOK CLAMPS
Proven locking pin clamp in a new cost saving design Enhanced locking pin clamp for airless transfer pallets Easy pin location adjustment using the XYZ shim box Built in pin riser for improved weld gun
More informationFLEX PIVOT NWP WELKER SMART STOPS* OR NAAMS STOPS. 100mm BORE NON-LOCKING PNEUMATIC CYLINDER* NPT OR G PORTS*
ISO 9001 REGISTERED FLEX PIVOT NWP FIXED SIDE MOUNTING WELKER SMART STOPS* OR NAAMS STOPS MOVABLE FLAT MOUNTING STYLE* MOVABLE BLADE MOUNTING STYLE* FIXED SIDE MOUNTING 100mm BORE NON-LOCKING PNEUMATIC
More informationCS1 COMPACT POWERED SLIDE
ISO 9001 REGISTERED CS1 COMPACT POWERED SLIDE WELKER 50mm BORE COMPACT CYLINDER NPT OR G PORTS OPTIONAL SOLID STATE CYLINDER SWITCH AVAILABLE METAL SHROUD KEEPS RAILS COVERED AT ALL TIMES (MOVES WITH )
More informationMAINTENANCE MANUAL LP SERIES RAIL SLIDES
ENGINEERED PRODUCTS ISO 9001 REGISTERED MAINTENANCE MANUAL LP SERIES RAIL SLIDES PNEUMATIC CYLINDER SHROUD SIDE SHROUD SIDE SHROUD LP1 SOLID STATE CYLINDER SWITCH CARRIAGE PLATE LP2 LUBE ACCESS PORT SHOCK
More informationMAINTENANCE MANUAL DS3 DOUBLE SHEAR LOCKOUT UNIT
ENGINEERED PRODUCTS ISO 9001 REGISTERED MAINTENANCE MANUAL DS3 DOUBLE SHEAR LOCKOUT UNIT 70mm BORE PNEUMATIC CYLINDER DOUBLE ROD SHOWN LOCKOUT DISK* SOLID STATE CYLINDER * *OPTIONAL SHEET 1 REV 2/14/2018
More informationMAINTENANCE MANUAL UPE/SPE PART EJECTORS LST/SST PART POSITIONERS
ENGINEERED PRODUCTS ISO 9001 REGISTERED MAINTENANCE MANUAL UPE/SPE PART EJECTORS LST/SST PART POSITIONERS TIP PLATE SIDE PLATE CAM SLOT UPE/SPE WORLD SWITCH (INTEGRATED) WORLD SWITCH (BOX-STYLE) SHROUD
More informationPIN CLAMP MAINTENANCE MANUAL PCS, PCT, PCM
ENGINEERED PRODUCTS ISO 9001 REGISTERED PIN CLAMP MAINTENANCE MANUAL PCS, PCT, PCM STANDARD BULLET NOSE PIN PNEUMATIC NPT or G PORTS STANDARD LOW PROFILE PIN STANDARD STEEL PART BACKUP SOLID STATE CYLINDER
More informationPSP SERIES PSP SHOT PIN. Superior part locating and positioning. Provides the best repeatability in its class. Patent Pending PSP01A
PSP SERIES PSP SHOT PIN Superior part locating and positioning. Provides the best repeatability in its class. Port Fittings Option Switch Options Weld Cover Option Patent Pending ORDERING DATA: SERIES
More informationSMART STOP TM WELKER SMART STOP DOES ALL STOPPING & SENSING FUNCTIONS IN ONE PART. MINIMIZES ENGINEERING, FIELD SET UP AND OPERATOR ADJUSTMENT TIME.
ISO 9001 REGISTERED SMART STOP TM TM WELKER SMART STOP DOES ALL STOPPING & SENSING FUNCTIONS IN ONE PART. MINIMIZES ENGINEERING, FIELD SET UP AND OPERATOR ADJUSTMENT TIME. ELIMINATES: n NEED FOR SEPARATE
More informationTPCA Power Clamps Catalog
TPCA Power Clamps Catalog Pneumatically Operated, Weld-Contamination Sealed, Heavy Duty Power Clamps > Degree of arm opening can be adjusted from -12 > One clamp for both dual or single arms > Uses TRILOK
More informationSMA Aluminum Cylinders
SMA Aluminum Cylinders PNEUMATIC TO 200 PSI HYDRAULIC 250 TO 400 PSI Non shock 1 1/8, 1, 2, 3 BORE SPACE SAVING AND CONVENTIONAL DESIGNS REPAIRABLE Very high quality Pancake type cylinders with all of
More informationSTABILIZER STABILIZER CYLINDERS
STABILIZER RAM Mechanical Locking Stabilizer cylinders replace manual systems used to position equipment at a desired location and height. Traditional methods to secure equipment are the use of crank type
More informationHIGH PRESSURE BALL VALVES
HIGH PRESSURE BALL VALVES HIGH PRESSURE BALL VALVES TABLE OF CONTENTS Page Description 3 Valve Design 3 Product Features 3 Available Options 3 2-Way with NPT and SAE Connections 4 2-Way with SAE Split
More informationPneumatic Cylinders. Series 3A and 3AN. Series 3A and 3AN
Series 3A and 3AN for Heavy-Duty Service n High-Tech Duralon Rod Bearing n State-of-the-Art Rod and Piston Sealing System n Heavy-Duty Piston-to-Rod Connection n1.50" 14.00" Bores n 150 250 psi Pressure
More informationSMS Solid Stainless Cylinders
SMS Solid Stainless Cylinders Space Saving and Conventional Lengths Pneumatic to 200 PSI Hydraulic 400 to 500 PSI Non shock /8,, 2, 3 Bore 300 Series Stainless Exterior Assures Aesthetics and Function
More informationLinear Slides Pneumatic
Linear Slides Pneumatic Mini DLM Modular Series DLM Series No Adaptor Plates Required! DLM-07M-50-50-P mini linear slide. Shown smaller than actual size. Highly Configurable Modular Automation Exclusive
More informationParallel Grippers- DPW DIRECTCONNECT Wide Body Series
DPW SERIES 1.196 Parallel Grippers- DPW DIRECTCONNECT Wide Body Series DIRECTCONNECT Connectivity: DIRECTCONNECT Tapped and Dowel mounting on body. Large or Wide Parts: Wide body design provides secure
More informationMAINTENANCE MANUAL MPE PART EJECTOR MST PART POSITIONER
ENGINEERED PRODUCTS ISO 9001 REGISTERED MAINTENANCE MANUAL MPE PART EJECTOR MST PART POSITIONER WORLD SWITCH MPE MST STANDARD SHROUD PNEUMATIC CYLINDER SOLID STATE CYLINDER SWITCH SHEET 1 REV 4/29/2016
More informationBimba Extruded Linear Thrusters 2X FF X EE DP 2X DD 2X Ø DD X EE DP U V W X Y Z R S Dimensions - ET T B 4X TAP AA THRU Ø BB C BORE X CC DP (OPP.SIDE)
Bimba Extruded Linear Thrusters Engineering Specifications Maximum Operating Pressure 140 psi (10 bar) Temperature Range 15 to 160 degrees F (-10 to 70 degrees C) Expected Service Life 1,500 miles (with
More informationSTRETCH ROD CYLINDERS for Krones Stretch Blow Molding Machines
PACKAGING COMPONENTS PLASTIC GROUP BCK STRETCH ROD CYLINDERS for Krones Stretch Blow Molding Machines Quality Delivery Support SOLUTIONS A division of PHD Simplified Pneumatic System Easy Maintenance Better
More informationFor material handling and clamping of small workpieces
For material handling and clamping of small workpieces Power Clamp Cylinder New ø25, ø32 Compact Type INFORMATION 34 mm Lightweight Compact High clamping force Lock function 53 mm Lightweight Weight :
More informationUnique CORROSION RESISTANT PLASTIC SLIDE UNIT FEATURES. Major Benefits. Industry Uses
Unique CORROSION RESISTANT PLASTIC SLIDE Model# ML305733 PLASTIC SLIDE PET GRIPPERS UNIT FEATURES Bore Size: Stroke: Body: Tool Plate: Guide Shafts: Retaining Rings: Fasteners: 2X 32 mm DIA 2.000 +.080/-.000
More informationSMA Aluminum Cylinders
SMA Aluminum Cylinders PNEUMATIC TO 200 PSI HYDRAULIC 250 TO 400 PSI Non shock /8,, 2, 3 BORE SPACE SAVING AND CONVENTIONAL DESIGNS REPAIRABLE Very high quality Pancake type cylinders with all of the engineering
More informationUser Guide: TPCA Power Clamps
734592D User Guide: TPCA Power Clamps Covers Standard TPCA42, TPCA52, TPCA62, and TPCA82 Clamp Models. 2X M8X1.25 16. NEAR/FAR SIDE 15.±.1 11.±.1 63.5±.1 4.±.5 9. PIVOT POINT 36.5±.5 111.5 32.±.1 45.±.3
More informationFisher 1061 Pneumatic Piston Rotary Actuator with Style H & J Mounting Adaptations
Instruction Manual 1061 H & J Actuator Fisher 1061 Pneumatic Piston Rotary Actuator with Style H & J Mounting Adaptations Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...
More informationYour Global Flow Control Partner. Series 92/93 Pneumatic Actuators. Technical Manual
Your Global Flow Control Partner Series 92/93 Technical Manual TM-1056 Pneumatic Actuator - 04/18/2017 Bray Series 92/93 Technical Manual - Table of Contents Topic...Page(s) Actuator Installation Notes...
More informationMobile Cylinder Div. Standard Build Series. Catalog HY /US Rev C
Mobile Cylinder Div. Standard Build Series Catalog HY18-0014/US Rev C WARNING - USER RESPONSIBILITY FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE
More informationDME HYDRAULIC LOCKING CORE PULL CYLINDERS Specification No. ME-E (A) Part No. HLCP-PS02 Page 1 of 13
Specification No. ME-E32-0002(A) Part No. HLCP-PS02 Page 1 of 13 IMPORTANT SAFETY INFORMATION 1. To avoid injury, exercise caution by reading these instructions before servicing or operating the system.
More informationUT Series. Pneumatic Actuators. UT-**-DA Series UT-**-SR Series. A full range of double acting and spring return actuators designed
UT-**-DA Series UT-**-SR Series A full range of double acting and spring return actuators designed to NAMUR for air supply ports and top mounting with ISO 5211 for base mounting patterns. Features Dual
More informationSMA Aluminum Cylinders
SMA Aluminum Cylinders PNEUMATIC TO 200 PSI HYDRAULIC 250 TO 400 PSI Non shock /8,, 2, 3 BORE SPACE SAVING AND CONVENTIONAL DESIGNS REPAIRABLE Very high quality Pancake type cylinders with all of the engineering
More informationSMS Solid Stainless Cylinders
SMS Solid Stainless Cylinders Space Saving and Conventional Lengths Pneumatic to 200 PSI Hydraulic 400 to 500 PSI Non shock /8, /2, 2, 3 Bore 300 Series Stainless Exterior Assures Aesthetics and Function
More informationSpring Return and Double Acting Pneumatic Quarter-turn Actuators Operations Manual
Spring Return and Double Acting Pneumatic Quarter-turn Actuators Operations Manual Table of Contents General..................... 1 Pneumatic Recommendations... 1 Construction................. 2 Disassembly
More informationDURA-SCAPE CC-SERIES. Non-Rotating Air Cylinder CC-1 CC-2 TECHINICAL SPECIFICATION OPERATING PRINCIPLES
CC Series of Non-Rotating Air Cylinders are designed as multi purpose units. The CC series is designed for applications where all the features of our SC series are not required, while still offering the
More informationINTEGRATED HYDRAULIC BRAKE
INTEGRATED HYDRAULIC BRAKE INTEGRATED HYDRAULIC BRAKE The integrated hydraulic brake is comprised of a pneumatic cylinder that acts as an actuator and an oleo-dynamic circuit that acts as a brake. The
More informationPNEUMATIC SLIDES (SERIES ZA)
ZA PNEUMATIC SLIDES (SERIES ZA) Bore 2x6, 2x8, 2x12, 2x16 or 2x20 mm. Stroke from 10 mm to 150mm. Optional end of stroke adjustments using shock absorbers, rubber bumpers, (FGD) or grub screw, (FPD). Optional
More informationHEAVY LIFTERS FOR MATERIAL HANDLING
HEAVY LIFTERS FOR MATERIAL HANDLING Ideal for automated, high load part liftg the automotive and assembly mache builder dustries Available as a drop- replacement M002 Mountg M001 Mountg Switches Stop Collars
More informationAV INSTALLATION, OPERATION & MAINTENANCE MANUAL
Rack & Pinion Pneumatic Actuators AV INSTALLATION, OPERATION & MAINTENANCE MANUAL AVCS PO Box 68172 Minneapolis, MN 55418 TABLE OF CONTENTS CHAPTER 1: PRODUCT DESCRIPTION 3 CHAPTER 2: TECHNICAL FEATURES
More informationSLIDE UNITS (for pneumatic cylinders)
SLIDE UNITS (for pneumatic cylinders) Series J J 10 A 5 5 100 B J SERIES Slide Units Series Cylinder option Stroke (mm) Cylinder bore size (mm) Size of slide unit With scraper bearings (always) Slide Unit
More informationHTR TIE-ROD CYLINDERS H I K M N TUBE OD
1 Brand Cylinders LINE THE HTR Pressure Ratings: 2" - 4" Bore = 2500 PSI, 5" Bore = 2000 PSI BORE (INCH) B C D E F G = J 2.0 1.015 2.125 1.625 1.000 1.000 1.142 2.5 1.015 2.125 1.625 1.000 1.000 1.142
More informationSERIES SCV SLIDES DESIGN 2/6 INFORMATION SHEET
SERIES SC SLIDES DESIGN / INFORMATION SHEET IMPORTANT INFORMATION DO NOT DISCARD! Use this information sheet to assist with slide installation and setup. File with maintenance or machine documentation.
More informationLION HYDRAULIC TIE-ROD CYLINDERS
LION HYDRAULIC TIE-ROD CYLINDERS 2 and 2-1/2 have 3/8 NPT Ports Rest have 1/2 NPT ports Double Ported NPFT Inline Ports M1 LH SERIES 3000 PSI Size Inches Pin to Pin Our Price Bore & Rod Center Cylinder
More informationQUICK INDEX. Series SMA Aluminum. Pancake and conventional lengths 1 1/8 thru 3 bore. Series SMS Solid Stainless
QUICK INDEX A U R O R A A I R P R O D U C T S Series SMA Aluminum Pancake and conventional lengths /8 thru 3 bore Series SMS Solid Stainless Pancake and conventional lengths for hostile environments Series
More informationSERIES BCS STRETCH ROD CYLINDERS
BCS y Q ua lit Support SOLUTIONS for the Plastic Bottle Blowing Industry DIRECT REPLACEMENT FOR SIDEL SERIES AND SERIES MACHINES P U O C PACK TI A S y er iv el D ENTS GR N O G COM P IN G SERIES BCS STRETCH
More informationFour Shaft Linear Thrusters
Four Shaft Linear Thrusters FOUR SHAFT THRUSTERS Three Models with bores from 2 to 4 Twice the load capacity of comparable two shaft units Reduced deflection and bearing play Compact, light weight robust
More informationTHD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS
THD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS INTRODUCTION A-T Controls THD scotch yoke actuators have been designed and engineered to
More informationTwin-Trak Component Tech-Sheets
Twin-Trak Component Tech-Sheets McGINTY CONVEYORS, INC. 5002 W. WASHINGTON ST. INDIANAPOLIS, IN 46241 PHONE: (317) 244-3353 FAX: (317) 240-4323 EMAIL: info@mcgintyconveyors.com WEB: www.mcgintyconveyors.com
More informationFULL COLOR TAB #11 IT AB121
FULL COLOR TAB #11 IT AB121 208 AB121 Air SERIES: AUTO RECIPROCATING AIR BOOSTER Model Numbers: AB121 & AB221 This 2:1 ratio air-to-air booster is compact and self-contained. Unit incorporates integral
More informationSERIES: AB2 WITH AIR RESERVOIR Model AB2 Air Booster furnished with Air Reservoir. Anodized Aluminum Tube and End Cap construction. How to order: AB2
SERIES: AUTO RECIPROCATING AIR BOOSTER This 2: ratio air-to-air booster is compact and self-contained. Unit incorporates integral valve components to perform auto-reciprocating function. Can amplify inadequate
More informationXRAY Grippers - Extreme Force and Torque. Patented Synchronous Technology - Extended Life
XRAY XRAY Grippers - Extreme Force and Torque The XRAY concept was developed for applications that impart high acceleration to heavy objects or require extremely long, precisely positioned jaws. These
More informationParallel Grippers. Body One piece anodized aluminum body
Catalog 19-2/US Features Rack and Pinion Rack and pinion drive mechanism provides synchronous motion. Body One piece anodized aluminum body Bushings Four composite bushings provide the support needed for
More informationpneumatic swing clamps
pneumatic swing clamps Sizing and Application Chart Series Standard Features Bore Clamping Clamping Force [lbf.]n 90 Series [0.86] 22 [0.] 13 [34] 0 Arm rotates at the top of stroke Shielded rod protects
More information2500 PSI STANDARD FEATURES 2500 PSI CYLINDERS
2500 PSI STANDARD FEATURES Intended Use: Double acting applications Rated Pressure: 2500 PSI Material: High Tensile SAE C1045, ground and polished hard chrome plated Barrel Material: High tensile SAE C1026/St52.3
More informationSeries SS Solid Stainless Cylinders
Series SS Solid Stainless Cylinders Pneumatic to 200 PSI Hydraulic to 000 PSI Non shock 3/4, /8,, 2 Bore To Help Brighten Your Corner of the World. All exterior components 300 series stainless A U R O
More informationREPAIR PROCEDURES MANUAL
REPAIR PROCEDURES MANUAL PVX Series Vane Pumps A Design Series Step-by-Step Guide to Troubleshooting and Repairing PVX Series Vane Pumps Introduction Thank you for choosing Continental Hydraulics PVX Vane
More informationAngle Seat Valve /2" up to 3"
1/ up to up to 428 F Pneumatically operated angle seat valve for the control of neutral and aggressive gases, liquids and steam. Compact design For temperatures from -22 F up to +428 F Working pressure
More informationHeavy Duty Bench Top Presses
Heavy Duty Bench Top Presses Model: BTP-501 (FOR SINGLE PISTON ROD, 5 BORE, MF1 MOUNT CYLINDERS) Model: BTP-502 (FOR TRA TRIPLE PISTON ROD, 5 BORE, MF1 MOUNT CYLINDERS) Heavy Duty Bench Top Press shown
More informationConstruction characteristics. Technical characteristics. End plates Rod Barrel Rod-guide bushing Piston
Construction characteristics nd plates Rod Barrel Rod-guide bushing Piston Seals Cushion adjusting screws die-casting aluminium C3 chromed steel or stainless steel aluminium alloy anodised spheroid bronze
More informationPNEUMATIC ROTARY ACTUATORS
Bulletin FRA.C-09 Prices effective September 1, 2011 PNEUMATIC ROTARY ACTUATORS FRA & FRC Series FRA Series Features 1. Magnetic pistons are standard on all models. 2. Compact design saves space. 3. Rectangular
More informationINSTALLATION, OPERATION & MAINTENANCE MANUAL
Rack & Pinion Pneumatic Actuators INSTALLATION, OPERATION & MAINTENANCE MANUAL QSM, Inc. 127 Village Lane Easley, SC 29642 U.S.A. Ph: (864) 605-0150 Fax: (864) 605-0830 www.tru-flo.com TABLE OF CONTENTS
More informationParallel Grippers- Two Jaw Precision Spring Series
Courtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (8) 426-548 www.cmafh.com 1.186 TM Parallel Grippers- Two Jaw Precision Spring Series Mounting Information: Grippers
More informationHinge cylinders DFAW
Key features At a glance Hinge cylinder for clamping components during the welding process Sintered bronze bushes as lowfriction bearing material on rod clevis and swivel bearing Clamping unit: With piston
More informationKRONES DIRECT REPLACEMENTS
PLASTIC PACKAGING COMPONENTS GRO Quality Support Delivery SOLUTIONS A BLOW division MOLDING SOLUTIONS of PHD PLASTIC PACKAGING COMPONENTS P KRONES DIRECT REPLACEMENTS phdinc.com (800) 624-8511 INCREASE
More informationPneumatic cylinders series CX Double acting with magnetic piston, ISO 15552, stainless steel G1/8 to G1/2 piston Ø 32 to 100 mm
Pneumatic cylinders series CX Double acting with magnetic piston, ISO 15552, stainless steel 000 400 Order code CX-032-0250-000 Note: Piston Ø 125, 160 and 200 on request. Series Piston Ø Stroke length
More informationDisplacement. (cc/rev) Tap Water Sea Water PC PV
J anus Pumps - Axial Piston Totally oil free, clean and completely safe for people, processes and products. As a result of employing advanced materials, high velocity and loaded sliding surfaces can operate
More informationFULL COLOR TAB #12 BTP
FULL COLOR TAB #12 BTP 216 HEAVY DUTY BENCH PRESS BTP - How to MODEL: BTP-501 FOR SINGLE PISTON ROD, 5.00 BORE, MF1 MOUNT CYLINDERS Heavy Duty Bench Top Press shown with 5.00 Bore three (3) Stage Multi-Stage
More informationBTPSeries. BenchTopPress. Cylinders 95% OFOURCYLINDERSSHIPIN2-3DAYS! ONEDAYRUSHSERVICEAVAILABLEONALLCATALOGEDCYLINDERMODELS!
BTPSeries BenchTopPress& BenchTopPress Page196 Press Page199 95% OFOURCYLINDERSSHIPIN2-3DAYS! ONEDAYRUSHSERVICEAVAILABLEONALLCATALOGEDCYLINDERMODELS! HEAVY DUTY BENCH PRESS BTP - How to MODEL: BTP-501
More informationAngle Seat Valve 7010
Angle Seat Valve 7 DN 8 up to DN 8 PN 16 - PN Pneumatically operated angle seat valve for the control of neutral, slightly aggressive and highly aggressive media. Compact design Unaffected by lightly contaminated
More informationFig Variable Speed Valve Parts
5 DISASSEMBLY OF VARIABLE SPEED CONTROL VALVE (Seal Replacement with Control Valve in the Bobcat). Remove seat and seat plate (Fig. ).. Remove variable speed control lever linkage rod. 3. Remove temperature
More informationSERIES MH (NFPA) CYLINDER
MH SERIES TAB 58 Floating Rod Bushing SELF ALIGNMENT FEATURE Rod Bushing is designed to float.002 to improve bearing surface alignment. SERIES MH (NFPA) CYLINDER Reduces cylinder drag and erratic operation
More informationAngle Seat Valve 7010
Angle Seat Valve 7 DN 8 up to DN 8 PN 16 - PN 4 Pneumatically operated angle seat valve for the control of neutral, slightly aggressive and highly aggressive media. Compact design Unaffected by lightly
More informationContents. Hydraulic Cylinder
Hydraulic Cylinder Contents Tie Rod Cylinders of 2500psi series----------------------------------------2~3 Tie Rod Cylinders of 3000psi series----------------------------------------4~5 NFPA interchangeable
More informationDrawings for fabricating a StoolZippa from EHS Manufacturing.
Drawings for fabricating a StoolZippa from EHS Manufacturing. These drawings also include all critical dimensions and component information to manufacture your own closing wheel. This critical information
More informationClippard offers more types of miniature pneumatic cylinders for the MINIMATIC CYLINDER
MINIMATIC CYLINDER Clippard offers more types of miniature pneumatic cylinders for the designer s convenience, including: spring return, spring extend, air retract, double-acting and double rod models.
More informationHinge cylinders DW Key features
Key features At a glance Hinge cylinder for clamping components during the welding process Easy assembly thanks to swivel bearing on the bearing cap Integrated flow control Integrated end-position cushioning
More informationHigh-Torque, Easy Speed & Stroke Control, Field Adaptable
D R I V I N G T H E I N D U S T R Y F O R W A R D High-Torque, Easy Speed & Stroke Control, Field Adaptable Fully Adjustable Stroke Length and Jaw Stop Positions Flow Controls Fitted as Standard Quick
More informationbrochure PN
brochure PN-2013-01 www.bitorq.com/pneumatic.html Pneumatic Actuators PAGES 4-11 ON THE WEB AT BITORQ.COM/PNEUMATIC_PN.HTML COMPACT, RELIABLE DESIGN OPEN-CLOSED ADJUSTMENT STOPS DOUBLE ACTING AND SPRING
More informationActuator Maintenance Manual, E-Type size 8 to 150
English Actuator Maintenance Manual, E-Type size 8 to 150 Precautions - Warning Always take care to follow this manual in order to correctly maintain the TruTorq actuators. Before removing the actuator,
More informationCompact Cylinder. Series SZ. Specifications. Features: Features. Ø12mm - 100mm
SZ Compact Cylinder Specifications Features Type Series Compact Cylinder SZ Configurations SZ6 Double Acting, Single Rod, SZD6 Double Acting, Double Rod, SZV6 Double Acting, Non-Rotating, SZ7 Single Acting,
More information22mm. Compact Guide Cylinder (Basic type) New. Up to. Series MGP. Weight reduced!
1-161 Compact Guide Cylinder (Basic type) ø12, ø16, ø20, ø25, ø32, ø40, ø50, ø63, ø80, ø100 Up to 17% Weight reduced! New Weight reduced by up to 17% with a shorter guide rod and thinner plate Guide rod
More informationSUBJECT: INTEGRATED FUEL SYSTEM (IFS) UNIT PUMP SERVICE
DATE: July 30, 2010 SERVICE BULLETIN SUPERSEDES: S.B. 560 dated November 22, 2008 NO: 560R1 SUBJECT: INTEGRATED FUEL SYSTEM (IFS) UNIT PUMP SERVICE RELATED PUBLICATIONS: IFS OPERATION AND INSTRUCTION MANUAL
More informationCONTROLS. Bray Pneumatic Actuators & Accessories. Technical Manual. A Division of BRAY INTERNATIONAL, Inc.
CONTROLS A Division of BRAY INTERNATIONAL, Inc. Bray Pneumatic Actuators & Accessories Technical Manual TM-056 Pneumatic Actuator - 08//00 Bray Pneumatic Actuators & Accessories Technical Manual - Table
More informationCylinders. Series TQ Agricultural Cylinders. Vickers. Nominal Pressure: 2500 psi
Vickers Cylinders Series TQ Agricultural Cylinders Nominal Pressure: 500 psi Released 10 91 113A Series TQ Hydraulic Cylinders Designed for Agricultural Applications Features Working pressure to 500 psi
More information82L Series. Pneumatic Power Clamps Ordering Information 03 B8 H 82L 2G B PC-PPC-15. Base Model Size Description 2G 3G 3N 4G 4N
82L..-2... Series Pneumatic Power Clamps Ordering Information 82L 2G B -2 3 B8 H Base Size Description Arm Style Description 2G 3G 3N 4G 4N Ø25 (G1/8) Cylinder Bore Size Ø32 (G1/8) Cylinder Bore Size Ø32
More information