SMS Solid Stainless Cylinders
|
|
|
- Adela Florence Haynes
- 5 years ago
- Views:
Transcription
1 SMS Solid Stainless Cylinders Space Saving and Conventional Lengths Pneumatic to 200 PSI Hydraulic 400 to 500 PSI Non shock /8, /2, 2, 3 Bore 300 Series Stainless Exterior Assures Aesthetics and Function in Washdown Applications or other Harsh Environments A U R O R A A I R P R O D U C T S 35
2 SMS DESIGN FEATURES Piston rod is hard chrome plated type 303 stainless Rod extension/wrench flats are long enough to fit standard wrenches. Special heavy duty wiper not only seals out solid contaminants but also effectively prevents liquids and gases from entering the cylinder interior. End caps are type 303 stainless steel Clean crevice free threaded construction assures maximum strength and allows easy wash down Heavy /8 wall type 304 stainless tube is precision honed Brass or aluminum piston is attached with a high strength threaded joint. Reduce noise and fatigue problems such as rod breakage with urethane/nitrile shock pads. Add /4" to the cylinder length for each pad. Pneumatic use only to 80 F. Pneumatic rod seal is a "longlife" nitrile cup. Hydraulic rod seal is pressure energized and extra long wearing for improved sealability. Composite rod bushing has high temperature capability and excellent chemical resistance. Solid lubricant fillers provide excellent wear characteristics for non-lube service. The bearing is inboard of the wiper and seal, away from the environment Optional wick provides teflon lube for non-lube service on O ring piston. Standard piston seal is large cross section O ring. Compounds are carefully selected for maximum cycle life. Optional U cup piston seals with teflon wear strip stretch the limits of service even futher. Reduce friction and operate without lube in the severest applications while extending or eliminating the service interval. If space permits for applications involving side loads or long strokes, select SMS, 2, 3, 5, 7, 8, 9, which have extra long bearings with added space between support points. Strokes longer than the maximum listed in the ordering procedure can be produced but careful consideration must be given to how the cylinder is applied how well is the load supported or guided, is the cylinder used in push or tension, is the cylinder vertical or horizontal, etc. Consult factory on all strokes longer than standard. Stroke increments other than standard can also be made. Special lengths are generally available in a few days and are priced as "non-standard" strokes. TM 36
3 /2 BORE SMS STAINLESS 200 PSI MAX. AIR 500 PSI MAX. HYD. Non shock SMS SMS2 2 3/4 /8-27 NPT 2 3/32 + STROKE 7/6 /8-27 NPT /4-2 UNF.249 PILOT.246 x /64 LG. 3/4 / 2-24 x 5/8 DP. 3 7/8 + STROKE 2 9/6 /6 7/6 3/4 Spring Return Cylinders Pneumatic only Springs add to cyl. length 0-2 stroke add /2 extra 2 /2-4 stroke add 3 extra over 4 stroke not available Spring force Fully extended 5# Fully compressed 50# Spring material Stainless steel Optional Male Rod Thread I.D. /8-27 NPT /4-2 UNF /2.249 PILOT.246 x /64 LG. -24 x 5/8 DP. /2-20 UNF 2A SMS /6 + STROKE 7/6 3/4 /4-2SS Nut Nose Mounting Nut Not included with cylinder Order Separately 7/8 23/32 /8-27 NPT /4-2 UNF.249 PILOT.246 x /64 LG. /2-24 x 5/8 DP. SMS5 /4-20 UNC THR'D. EQUAL SPACED ON 2.87 B.C. (CLEARANCE FOR #0 S.H.C.S.) 2 3/32 + STROKE 5/8 3/4 7/6 SS-500 Rod Clevis and Nut /6 2 /4 SMS6 2 5/8 7/ /4-2 UNF.249 PILOT /8-27 NPT.246 x /64 LG. 2 5/32 + STR 9/6-24 x 5/8 /2 /2-24 x 5/8 DP. /2-20 THREAD 303 Stainless 7/8 SQUARE.377 SS-50 Clevis Pin Assembly Used on SS Stainless /8-27 N.P.T. 5/8 + STR CLEAR /4-20 S.H.C.S., 5/6-8 x 5/8, 40
4 ALL AURORA PRODUCTS AVAILABLE FOR 24 HOUR DELIVERY TM SMS Options Shock Pads Viton Seals Non-lube Service Magnetic Piston U Cup Piston Non-rotate (SMA 7,8,9) 90 Rear Clevis SSC-90 Low Profile Clevis Brk t Used on SMS /32 /4 /4 /4 TYP. SS-00 St d Clevis Brk t Used on SMS 2 9/6 /6 SS-00T Trunnion Brk t Used on SMS 0, 304 Stainless 3/32 7/64 THRU, 4 PLC. /32 2 PLC. 3/6 /2 R. /2 R. /32 2 PLC. 3/ /4 SQUARE /2 /4 2 /4 /2 / THRU 5/8.500 THRU 5/8 SMS7 SMS8 SMS /32 + STROKE 7/32 9/6 /2-24 x 5/8.375 /8-27 N.P.T. 2 /8-27 N.P.T /6 2 7/32 + STR /8-27 N.P.T. /8-27 N.P.T. CLEAR /4-20 S.H.C.S., CLEAR /4-20 S.H.C.S., 5/6-8 x 5/8, 2 3/32 + STROKE 9/6 /2-24 x 5/8 /6 CLEAR /4-20 S.H.C.S., 5/6-8 x 5/8, 3 3/6 + STROKE 9/6 /2-24 x 5/8 2 3/32 + STROKE 3/4 TYP. /6 5/6-8 x 5/8, -24 x 5/8 /2 Series SMS Solid Stainless 9/6 /4 /6 2 /4 All Aurora Cylinders are 00% Factory Tested to insure Trouble Free Performance SMS0 SMS /8-27 N.P.T. /8-27 N.P.T. 2 /8-27 N.P.T. 3/6 3 3/6 + STROKE 3/4 TYP. 3/6 3/32 TYP. -24 x 5/8 3/32 TYP /
5 /2 BORE SMS STAINLESS 200 PSI MAX. AIR 500 PSI MAX. HYD. Non shock 2 SMS4 2 3/6 + STROKE /8-27 NPT 3/32 + STROKE 7/32 7/32 /4-20 UNC THR'D. EQUAL SPACED ON 2.87 B.C. (CLEARANCE FOR #0 S.H.C.S.) /2-24 x 5/8 DP. 2 5/8 2 /4 /4-20 UNC THR'D. EQUAL SPACED ON 2.87 B.C. (CLEARANCE FOR #0 S.H.C.S.) Spring Return Cylinders Pneumatic only Springs add to cyl. length 0-2 stroke add /2 extra 2 /2-4 stroke add 3 extra over 4 stroke not available Spring force Fully extended 5# Fully compressed 50# Spring material Stainless steel Optional Male Rod Thread 3/4 2 /4 2 /8-27 NPT SMS /6 9/6 /8-27 NPT 2 7/8 + STROKE 7/32 /2-24 x 5/8 DP. 2 5/8 /4-20 UNC THR'D. EQUAL SPACED ON 2.87 B.C. (CLEARANCE FOR #0 S.H.C.S.) 2 /4 SS-500 Rod Clevis and Nut /2-20 UNF 2A /6 2 SMS I.D. /8-27 NPT 3/32 + STROKE 5/8 7/32 /2-24 x 5/8 DP. 2 5/8 /4-20 UNC THR'D. 8 HOLES EQUAL SPACED ON 2.87 B.C. (CLEARANCE FOR #0 S.H.C.S.) /2-20 THREAD 303 Stainless 7/8 SQUARE.377 SS-50 Clevis Pin Assembly Used on SS Stainless 2 /4 SMS7 SSC-90 Low Profile Clevis Brk t Used on SMS /32 /4 3/ /32 /8-27 NPT -24 x 5/8 DP. SS-00 St d Clevis Brk t Used on SMS 6 /32 2 PLC. /2 2 5/8 /2 R. /2.500 THRU 5/8 All Aurora Cylinders are Fully Repairable /4 /4 TYP. 3/4 SQUARE 7/64 THRU, 4 PLC. 9/6 /6 3/6 /4 2 /4 42
6 ORDERING PROCEDURE - SMS Stainless Select code numbers/letters (bold type) from each of the six boxes below - then select options desired from the table below. List codes in the same sequence as shown. Bore Code Type Code Service Code /8" /2" 2" 3" Double acting Single acting spring return (Adds to cyl. length) Spring extend not available C A Pneumatic Hydraulic E G Mounting Style/Code SMS SMS 2 SMS 3 SMS 5 SMS 6 SMS 7 SMS 8 SMS 9 SMS 0 SMS SMS 4 SMS 5 SMS 6 SMS 7 Stroke Code is stroke in total /8" increments Example: " stroke = 8 2 /4" stroke = 8 Stocked in the following strokes: /8, /4,, /2, 3/4,, /4, /2, 3/4, 2 and /2" increments to 0" 3" bore - Limited to 8" max. stroke Piston Rod Codes Bore Thread Code x 3/4 Male M /6-8 x 5/8 Female 5/6-24 x 5/8 Female F3 F4.500 /2-20 x Male M x 5/8 Female F x 5/8 Female F /8-8 x /8 Male M /2-20x 3/4 Female F /4-6 x /4 Male M /4-6 x Female F0 With non-rotate option enter code Option Description Code Extra rod extension /4 " increments Shock pads Pneu. only to 80 F Double acting only Specify code letter J followed by extra length required as a two place decimal om the table Example: J.50 = /2" extra J.25 = /4"extra Add to either or both ends in /8", /2", 2" bore up to 2" stroke. Over 2" stroke and on all 3" bore must be added to both ends Each pad adds /4" length Rod end only Cap end only Both ends Non-lube service Available on standard O ring Piston. Not available or necessary on U cup piston P Viton seals U cup piston Standard seals are nitrile and urethane +0 to +200 F For service 0 to +400 F specify viton Extends cycle life and reduces friction Piston is aluminum and includes teflon wear strip adds /2" to length Clevis 90 to std SMS 2, 6, only T Magnetic piston Adds /2" to length W Non rotate Available only on double acting SMS 7, 8, 9, 4, 5, 7 with male stud without male stud /4" oversize ports 2" bore only SMS, 2, 3, 6, 7, 8, 9, only Not available with option x,y Z J L M N R S X Y Part No. Example:.500 bore Mounting style SMS9.500 stroke /2-20 x male thread 5 SMS9 C 2 E M8 R W Double acting Pneumatic Magnetic piston Viton seals 48
7 SMS Service Parts When ordering any repair part please provide the part number and description shown below along with the serial number and part number of the cylinder being serviced. TM Key Description /8 Bore /2 Bore 2 Bore 3 Bore Seal kits for cylinders with O ring piston Pneumatic, Nitrile Pneumatic, Viton Hydraulic, Nitrile Hydraulic, Viton Add suffix NL for Non-Lube Add suffix NL for Non-Lube SMS 34 SMS 34V SMS 35 SMS 35V SMS 345 SMS 345V SMS 355 SMS 355V SMS 3420 SMS 3420V SMS 3520 SMS 3520V SMS 3430 SMS 3430V SMS 3530 SMS 3530V Seal kits for cylinders with U cup piston includes Teflon wear strip Pneumatic, Nitrile Pneumatic, Viton Hydraulic, Nitrile Hydraulic, Viton Rear port cap 2 Rear pivot cap 2 90 Rear pivot cap Side port cap Rear flange cap Square cap Tube Piston rod assembly Spring guide Pair Spring Magnet Flange head Nose Mount Head Short square Head Long square Head Square non rotate head Trunnion head Non-rotate guide bushing Cap end shock pad Head end shock pad Add suffix 250 for 2" bore /4 NPT Add suffix 250 for 2" bore /4 NPT Add suffix 250 for 2" bore /4 NPT Add suffix 250 for 2" bore /4 NPT Add suffix 250 for 2" bore /4 NPT SMS59 and SS325 supplied in pairs Add suffix NR for non-rotate Add suffix 250 for 2" bore, /4 NPT Add suffix 250 for 2" bore, /4 NPT Add suffix 250 for 2" bore, /4 NPT Pair SMS 54 SMS 545 SMS 5420 SMS 5430 SMS 54V SMS 545V SMS 5420V SMS 5430V SMS 55 SMS 555 SMS 5520 SMS 5530 SMS 55V SMS 555V SMS 5520V SMS 5530V SMS 0 SMS 05 SMS 020 SMS 030 SMS SMS 5 SMS 20 SMS 30 SMS 90 SMS 590 SMS 2090 SMS 3090 SMS 48 SMS 485 SMS 4820 SMS 4830 SMS 3 SMS 35 SMS 320 SMS 330 SMS 46 SMS 465 SMS 4620 part No. is T followed by the complete cylinder part number SMS part 3 No. is PR followed by the complete cylinder part number SMS 2 SMS 25 SMS 220 SMS 230 SS 2 SS 25 SS 220 SS 220 SMS 59 SS 325 SS 3220 SS 3230 SMS 4 SMS 45 SMS 420 SMS 430 SMS 0 SMS 05 SMS 020 SMS 030 SMS 44 SMS 445 SMS 4420 SMS 45 SMS 455 SMS 4520 SMS 45NR SMS 455NR SMS 4520NR SMS 45T SMS 455T SMS 4520T SMS 5 SMS 5 SMS 5 Consult factory 3MSP CSP 5CSP 2CSP 3MSP Series SMS Solid Stainless 49
SMS Solid Stainless Cylinders
SMS Solid Stainless Cylinders Space Saving and Conventional Lengths Pneumatic to 200 PSI Hydraulic 400 to 500 PSI Non shock /8,, 2, 3 Bore 300 Series Stainless Exterior Assures Aesthetics and Function
SMA Aluminum Cylinders
SMA Aluminum Cylinders PNEUMATIC TO 200 PSI HYDRAULIC 250 TO 400 PSI Non shock 1 1/8, 1, 2, 3 BORE SPACE SAVING AND CONVENTIONAL DESIGNS REPAIRABLE Very high quality Pancake type cylinders with all of
SMA Aluminum Cylinders
SMA Aluminum Cylinders PNEUMATIC TO 200 PSI HYDRAULIC 250 TO 400 PSI Non shock /8,, 2, 3 BORE SPACE SAVING AND CONVENTIONAL DESIGNS REPAIRABLE Very high quality Pancake type cylinders with all of the engineering
SMA Aluminum Cylinders
SMA Aluminum Cylinders PNEUMATIC TO 200 PSI HYDRAULIC 250 TO 400 PSI Non shock /8,, 2, 3 BORE SPACE SAVING AND CONVENTIONAL DESIGNS REPAIRABLE Very high quality Pancake type cylinders with all of the engineering
QUICK INDEX. Series SMA Aluminum. Pancake and conventional lengths 1 1/8 thru 3 bore. Series SMS Solid Stainless
QUICK INDEX A U R O R A A I R P R O D U C T S Series SMA Aluminum Pancake and conventional lengths /8 thru 3 bore Series SMS Solid Stainless Pancake and conventional lengths for hostile environments Series
Series SS Solid Stainless Cylinders
Series SS Solid Stainless Cylinders Pneumatic to 200 PSI Hydraulic to 000 PSI Non shock 3/4, /8,, 2 Bore To Help Brighten Your Corner of the World. All exterior components 300 series stainless A U R O
Series HB Solid Brass Cylinders
Series HB Solid Brass Cylinders For General Industrial Use in most nvironments 00 PSI Pneumatic 500 PSI Hydraulic Non shock,, /8,, Bores Magnetic piston available to operate Aurora stainless proximity
Series HB Solid Brass Cylinders
Series HB Solid Brass Cylinders or General Industrial Use in most nvironments 00 PSI Pneumatic 500 PSI Hydraulic Non shock,, /8, /, Bores Magnetic piston available to operate Aurora stainless proximity
Series HB Solid Brass Cylinders
Series HB Solid Brass Cylinders or General Industrial Use in most nvironments 00 PSI Pneumatic 500 PSI Hydraulic Non shock,, /8, /, Bores Magnetic piston available to operate Aurora stainless proximity
* Screw clearance to allow bolt head to pass through - no counter bores
Technical Data: Medium: Filtered, lubricated or nonlubricated, compressed air Operating Pressure 00 psig (.6 Bar) Max. Temperature Range: Standard Nitrile seals: -0 F to 00 F (-0 to 65 ) 50 F max. with
Stainless Steel Flat-I The Corrosion Resistant, IP69K Rated Solution for Low Profile Applications. We make things MOVE
Stainless Steel Flat-I The Corrosion Resistant, IP69K Rated Solution for Low Profile Applications We make things MOVE Stainless Steel Flat-I Stainless Steel Flat-I Cylinders are designed specifically for
ACTUATORS. F-Series Plus Cylinders Single and Double acting 9/16" to 3" bore. Technical features Medium: Filtered, lubricated or nonlubricated,
F-Series Plus ylinders Technical features Medium: Filtered, lubricated or nonlubricated, compressed air Operating pressure 200 psig (3.6 Bar) Max. Temperature range: Standard Nitrile seals: -40 F to 200
FP 106 x PTM - PS
Single and Double acting 9/6" to " bore Technical Data: Medium: Filtered, lubricated or nonlubricated, compressed air Operating Pressure 00 psig (.6 Bar) Max. Temperature Range: Standard Nitrile seals:
Provenair Series AN Cylinders Parts List / Service Instructions
Provenair Series AN Cylinders Parts List / Service Instructions 1-1/2, 2, 2-1/2, 3-1/4 and 4 BORES EXTRUDED BARREL CONSTRUCTION 5, 6, 8 and 10 BORES TIE ROD CONSTRUCTION TYPE: Aluminum, repairable, square
HYDRAULIC HEAVY DUTY
Catalog #HHD-16 12/16 HYDRAULIC HEAVY DUTY Series HHD 3000 PSI RATED 10-25-16 WARNING IMPROPER SELECTION, IMPROPER USE OR FAILURE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN CAN CAUSE PROPERTY DAMAGE,
SUPERIOR CONSTRUCTION FEATURES SERIES B AIR CYLINDERS, 1 2" THRU 2" BORE SIZE MAXIMUM PSI 250
SUPERIOR CONSTRUCTION FEATURES SERIES B AIR CYLINDERS, 1 2" THRU 2" BORE SIZE MAXIMUM PSI 250 ALUMINUM HEADS & CAPS LARGE PORTS PISTON PACKING PISTON WIPER BRONZE BEARING PACKING TUBE SEAL CYLINDER TUBE
FULL COLOR TAB #6 TC 105
FULL COLOR TAB #6 TC 105 SERIES TC 2-STAGE TELESCOPING CYLINDER CONSTRUCTION FEATURES 3 Bore Sizes: 0.75, 1.50 and 2.50 Strokes up to 60 2-Stage Telescoping Space Saving Design 100% Double Action Heavy-Duty
LP/LPM Series. Non-Lube Air Cylinder P1M. Tooling Plate P1M. Swing Clamp P1M. Contents E51
Non-Lube Air Cylinder P1G C05(S) LP(M) Swing Clamp Tooling Plate Contents Features...52 Ordering Information...53 Specifications...54 Basic Dimensions...55 Mounting Options...56 Spring Data...57 Rod Options...58
Flat Cylinders Flat-1 Square Flat-1 2.3-2.12 2.13-2.19 Flat Cylinders Flat-II Square Flat-II F02, F03, F04 (multiple power) FOP (multiple position) Flat Accessories Stainless Steel Flat-1 EF1 Cylinders
SERIES PA PNEUMATIC CYLINDERS FOR VALVE ACTUATION BORE SIZE: 3 1/4 TO 20 RATING: 150 PSIG (1000 KPA)
BORE SIZE: 3 /4 TO 0 RATING: 50 PSIG (000 KPA) PNEUMATIC CYLINDERS FOR VALVE ACTUATION FEATURES THE PA SERIES OF VALVE ACTUATORS ARE DESIGNED TO AUTOMATE VALVE OPERATION. THESE ACTUATORS CAN BE ADAPTED
ASP Series Steel Body NFPA Cylinder Line
Series Steel Body NFPA Cylinder Line www.numatics.com Table of Contents Series Features and Benefits 3 Standard Mounts 4 How to Order 5 Port Size Availability 6 Dimensions 7-34 Rod Ends 7 Large Bore 8
Clippard offers more types of miniature pneumatic cylinders for the MINIMATIC CYLINDER
MINIMATIC CYLINDER Clippard offers more types of miniature pneumatic cylinders for the designer s convenience, including: spring return, spring extend, air retract, double-acting and double rod models.
Series AM/MM/WM Mill Type Cylinders
ET AH To order this part, call Lifco Hydraulics USA Toll Free at -00-- S S ZE* SS* SW (TYP) FB THRU, () PLACES TE UF WA / EE P* ØE EE P* CD 00 M CW S Series AM/MM/WM Mill Type Cylinders Table of Contents
SRX Series Stainless Steel Body Air Cylinders with Continuous Position Feedback
with Continuous Position Feedback P P1L SRX SR/SRM, SR/SRM Contents Features... 42 Cylinder Ordering Information... 43 Specifications... 44 Engineering Specifications... 45 imensions...46-50 Mechanical
Mobile Cylinder Div. Standard Build Series. Catalog HY /US Rev C
Mobile Cylinder Div. Standard Build Series Catalog HY18-0014/US Rev C WARNING - USER RESPONSIBILITY FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE
HTR TIE-ROD CYLINDERS H I K M N TUBE OD
1 Brand Cylinders LINE THE HTR Pressure Ratings: 2" - 4" Bore = 2500 PSI, 5" Bore = 2000 PSI BORE (INCH) B C D E F G = J 2.0 1.015 2.125 1.625 1.000 1.000 1.142 2.5 1.015 2.125 1.625 1.000 1.000 1.142
The Lehigh Miracalube Air Cylinder The Only Real Self-Lube Air Cylinder in the World BENEFITS!
SERIES JHD HEAVY DUTY AIR CYLINDER The Lehigh Miracalube Air Cylinder The Only Real Self-Lube Air Cylinder in the World BENEFITS! The true test of a cylinder is how well it performs in your application.
TaskMaster Pneumatic Cylinder
TaskMaster Pneumatic Cylinder Index TaskMaster Cylinders Index Air to 200 psi, 1-1/2" thru 6" Bore Page 1-1/2" thru 4" Bore Features & Specifications 2 (profile version) How to Order 3-5 Mounting Styles
FA SERIES KNIFE GATE PNEUMATIC CYLINDERS... 8
FA SERIES KNIFE GATE PNEUMATIC CYLINDERS......... 8 section 8 154 ORDERING INFORMATION For Rod End Dimensions see back cover foldout... Dimensional Information FA SERIES DIMENSIONS BASIC DIMENSIONS PLUS
The friction free alternative
Rolling The Rolling Diaphragm Air Cylinder The advent of the long stroke rolling diaphragm as a means of low-friction dynamic sealing has led to the development of the ControlAir Diaphragm Air Cylinder.
RP SERIES 200 psi Mill-type Cylinder
Actuation Solutions and Systems for the SERIES 200 psi Mill-type Cylinder Delivering superior long-term performance and value Designed and engineered for severe-service applications Bore Size: 2 to 20
Position Control Hard chrome-plated carbon steel piston rod with blackened threads and wrench flats Sintered bronze rod bushing Internally lubricated
Position Control System Products Cylinders 7.3-7.9 Cylinder Rod Lock 7.10-7.11 Cylinder Accessories 7.12-7.15 Pneu-Turn 7.16-7.24 Position Control System 7.25-7.36 Digital Panel Meter 7.37-7.42 Electronic
RPD Series Delrin End Cap Roundline Plus Stainless Steel Body Actuators 9/16" to 2" bore Double acting pneumatic actuators
RP Series elrin nd ap Roundline Plus Stainless Steel Body ctuators 9/6" to 2" bore ouble acting pneumatic actuators elrin cetal Resin end cap cylinders for washdown, and corrosive environment application
Compact Select Cylinders Inch Series.
Compact Select Cylinders Inch Series Table of Contents: Inch Series Inch Series, Options and ccessories Inch Series How to Order: Inch Series... pg. Forces, Pressure Ratings, Envelope Dimensions... pg.
Original & T Series 8 Bores, 1/2" 4" Features & Benefits General, Standard Specifications
Original & T Series 8 Bores, /2" 4" Section Index Features & Benefits....2 General, Standard Specifications....2 Page Construction Details....3,.4 How a Pancake is built Information....5,.6 How a Pancake
Original Line Original Line How to Order Introduction to Bimba Standard Air Three-Position Air with Adjustable Cushions MRS Non-Rotating Air PC Steel Non-Repairable Original Line Steel Repairable (Bell
FULL COLOR TAB #12 BTP
FULL COLOR TAB #12 BTP 216 HEAVY DUTY BENCH PRESS BTP - How to MODEL: BTP-501 FOR SINGLE PISTON ROD, 5.00 BORE, MF1 MOUNT CYLINDERS Heavy Duty Bench Top Press shown with 5.00 Bore three (3) Stage Multi-Stage
BTPSeries. BenchTopPress. Cylinders 95% OFOURCYLINDERSSHIPIN2-3DAYS! ONEDAYRUSHSERVICEAVAILABLEONALLCATALOGEDCYLINDERMODELS!
BTPSeries BenchTopPress& BenchTopPress Page196 Press Page199 95% OFOURCYLINDERSSHIPIN2-3DAYS! ONEDAYRUSHSERVICEAVAILABLEONALLCATALOGEDCYLINDERMODELS! HEAVY DUTY BENCH PRESS BTP - How to MODEL: BTP-501
FULL COLOR TAB #16 TECHNICAL DATA
FULL COLOR TAB #16 TECHNICAL DATA 276 General How Force Charts Weight Charts Seal Kits Conversion Charts TECHNICAL DATA How to determine the right cylinder size for the job. To determine what cylinder
Options selector for T, VT, and ET V T S R 3 / 8 R C E N 1-1/8 5. 5/16" or 3/8"
Series T, T & VT Tiny Tim TUTORS /" and -/8" bore Single and double rod end styles Viton seals optional for higher temperatures Technical data Medium: ompressed air, filtered, lubricated or non-lubricated
Table of Contents General Specifications, Available Mountings... 1 Introduction... 2 Application Examples... 3 Features... 4 Theory of Operation... 5
With Continuous Position Feedback Catalog AU08-0971/NA September, 2002! Compact Design! Highly Accurate Position Feedback Capability! Electronic Controllers Available! 5 Bore Sizes Table of Contents General
DIMENSIONS & MOUNTS. NOTE: For Spring Return and Fail safe options, double the stroke when calculating overall dimensions HEAD NUT (SSSM-114)
STAINLESS STEEL SMALL BORE CYLINDERS SSSM (All Stainless Steel). Available in 1-1/8 bore only. MODEL REAR PORTED - NO TANG Model SSSM (All Stainless Steel). Available in 1-1/8 (28mm) bore only. Pressure
SERIES PSI OPERATING PRESSURE HEAVY HYDRAULIC DUTY CYLINDER HEAVY DUTY HYDRAULIC CYLINDER PURAKAL CYLINDERS, INC CYLINDERS, INC
CYLINDERS, INC SERIES 2500 3000 PSI ORATING PRESSURE HEAVY DUTY HEAVY HYDRAULIC DUTY CYLINDER HYDRAULIC CYLINDER PURAKAL CYLINDERS, INC PURAKAL P.O. Box 22038 CYLINDERS, INC P.O. Eugene, Box OR 22038 97402-0414
Catalog PAN2-2. Pancake. II Air Cylinders. Superior Interchangeable Industrial Air Cylinders
Catalog PN2-2 Pancake II ir Cylinders Superior Interchangeable Industrial ir Cylinders Pancake II Cylinders Product Index Standard Series PSD, PSR, PSX, PWD, PTD How it works....................................
Heavy Duty Bench Top Presses
Heavy Duty Bench Top Presses Model: BTP-501 (FOR SINGLE PISTON ROD, 5 BORE, MF1 MOUNT CYLINDERS) Model: BTP-502 (FOR TRA TRIPLE PISTON ROD, 5 BORE, MF1 MOUNT CYLINDERS) Heavy Duty Bench Top Press shown
RL-G70 PARTS LIST # I USE THIS PARTS LIST FOR: Hoist Serial Number 6597 to
RL-G70 PARTS LIST # 102693I USE THIS PARTS LIST FOR: Hoist Serial Number 6597 to For older hoists use the following: Parts List No. 102692H for Serial Number 2485 to 6596 IF YOUR HOIST DOES NOT FALL WITHIN
CATALOG FL-16-B THE LIGHT-WEIGHT LINE WITH HEAVY-DUTY FEATURES
HEAVY-DUTY CATALOG FL-6-B THE LIGHT-WEIGHT LINE WITH HEAVY-DUTY FEATURES TABLE OF CONTENTS CYLINDER FEATURES DOUBLE-ACTING Series T, TS, TL and TLS 4 DOUBLE-ACTING DOUBLE-ENDED Series TDE and TSDE 4 MAGNETIC
High Performance Repairable Pneumatic Cylinder Parker Hannifin Corporation
High Performance Repairable Pneumatic Cylinder 219 Pneumatic ivision eatures Optional Piston Magnet Located under wear band, piston magnet is used for through-thebarrel sensors for electronic piston position
TABLE OF CONTENTS CYLINDER FEATURES MOUNTING STYLES DOUBLE-ACTING Series T and TS 4 DOUBLE-ACTING DOUBLE-ENDED Series TDE and TSDE 4 MAGNETIC SWITCH D
HEAVY-DUTY CATALOG FL-6-A FLAIRLINE FAST Shipped in - days THE LIGHT-WEIGHT LINE WITH HEAVY-DUTY FEATURES TABLE OF CONTENTS CYLINDER FEATURES MOUNTING STYLES DOUBLE-ACTING Series T and TS 4 DOUBLE-ACTING
DURA-TRANS NB-SERIES. Bi-Directional Transfer NB-10 NB-20 TECHNICAL SPECIFICATION OPERATING PRINCIPLES 6-1.1
NB-SERIES NB Series of Bidirectional Transfer Devices, commonly known as tuckers, provide a practical low-cost method for automatic work positioning. The units are extremely compact and eliminate the need
P1E Series ISO Cylinders
High fibre nitrile Combined cushion/ Aluminium tube to Zinc diecast end plates Retained cushion piston rod seal non return seal for give high strength on 32, & 50mm bore adjusting screw allows a and polyurethane
Air/Oil Tanks Air Boosters Cylinder Options Multi-Stage Triple-Rod Basic Cylinders Accessories Technical Data TECHNICAL DATA: FORCE CHART BORE STROKE
How to determine the right size Cylinder for the job TECHNICAL DATA To determine what size cylinder the task requires, you need to answer a few questions about three main points: load, velocity and air
Double-Wall Cylinders/Repairable Stainless Steel Cylinders
Double-Wall Cylinders/Repairable Stainless Steel Cylinders Double-Wall Cylinders 6.3-6.15 Repairable Stainless Steel Cylinders 6.16-6.24 DW/RSS Cylinders Bimba Double-Wall Cylinders The Bimba Double-Wall
acting, spring return, spring extend and double rod models. Hall Effect sensors and magnetic piston versions are also available.
AIR FORCE ONE COMPACT CYLINDER Clippard Instrument Laboratory, Inc. Air Force One compact cylinders are available in double acting, spring return, spring extend and double rod models. Hall Effect sensors
Original Line Cylinders
How to Order Introduction to Bimba Standard Air.3.4-.9.0-.65 Three-Position.66-.67 Air with Adjustable Cushions.68-.75 MRS.76-.86 Non-Rotating Air.87-.97 PC.98-.03 All Stainless Steel Repairable (Bell
HEAVY DUTY PNEUMATIC CYLINDERS
HEAVY DUTY PNEUMATIC CYLINDES Features: Conforms to ISO:30 standard. Double Acting, with adj. cushioning at both ends. Sizes: Ø, Ø, Ø, Ø, Ø, Ø0, Ø1, Ø0, Ø0 & Ø0. : Other bore sizes on request Seamless
SERIES MH (NFPA) CYLINDER
MH SERIES TAB 58 Floating Rod Bushing SELF ALIGNMENT FEATURE Rod Bushing is designed to float.002 to improve bearing surface alignment. SERIES MH (NFPA) CYLINDER Reduces cylinder drag and erratic operation
250 psi rating. series. pneumatic cylinders. bulletin 0606ST.
20 psi rating series ST pneumatic cylinders bulletin 0606ST www.royalcylinders.com i Contents Page Description 1 Mounting Styles 2 Features Description Mounting dimensions 3 STNM No Mount (MX0) 3 STME
AS/ASH SERIES ALUMINUM PNEUMATIC AND HYDRAULIC CYLINDERS... 6
AS/ASH SERIES ALUMINUM PNEUMATIC AND HYDRAULIC CYLINDERS............. 6 Section 6 8 ORDERING INFORMATION For Rod End Dimensions see back cover foldout... Basic Cylinder No Mount.0" to 4.00" For pressure
KRONES DIRECT REPLACEMENTS
PLASTIC PACKAGING COMPONENTS GRO Quality Support Delivery SOLUTIONS A BLOW division MOLDING SOLUTIONS of PHD PLASTIC PACKAGING COMPONENTS P KRONES DIRECT REPLACEMENTS phdinc.com (800) 624-8511 INCREASE
Bimba Extruded Linear Thrusters 2X FF X EE DP 2X DD 2X Ø DD X EE DP U V W X Y Z R S Dimensions - ET T B 4X TAP AA THRU Ø BB C BORE X CC DP (OPP.SIDE)
Bimba Extruded Linear Thrusters Engineering Specifications Maximum Operating Pressure 140 psi (10 bar) Temperature Range 15 to 160 degrees F (-10 to 70 degrees C) Expected Service Life 1,500 miles (with
Actuator Products Compact Cylinders
Low profile design Flexible construction with special modification capability High density iron rod bearing provides maximum support for longer life Single and double acting versions available 6 mounting
PURAKAL SERIES 100 TABLE OF CONTENTS
TABLE OF CONTENTS How to Order Cylinder......................... Repair Kit......................... Seal Kit......................... Warranty......................... Parts List.........................
Original Line Cylinders
How to Order Introduction to Bimba 1.3 1.4-1.9 Standard Air 1.10-1.66 Three-Position 1.67-1.68 Air with Adjustable Cushions 1.69-1.76 MRS 1.77-1.87 Non-Rotating Air 1.88-1.98 PC 1.99-1.104 Steel Non-Repairable
Catalog PAN2-2. II Air Cylinders. Pancake. Superior Interchangeable Industrial Air Cylinders
Catalog PN- Prices effective September 1, 011 Pancake II ir Cylinders Superior Interchangeable Industrial ir Cylinders 5-8-10 Pancake II Cylinders Product Index Standard Series PSD, PSR, PSX, PWD, PTD
STAINLESS STEEL CYLINDER CONSTRUCTION
STAINLESS STEEL CYLINDER CONSTRUCTION In the early 950 s, Clippard introduced miniature pneumatic cylinders and valves to industry. No other manufacturer can boast of the same experience or knowledge of
Cylinders Small Bore Tie Rod
Cylinders Small Bore Tie Rod Reference Control Valves Cylinders Specialty Valves Production Devices Index Cylinder Materials Heads: Tubes: Piston: Rod: Bearing: Piston and Rod Seals: Rod Wiper: Tie Rods:
Cylinders. Series TQ Agricultural Cylinders. Vickers. Nominal Pressure: 2500 psi
Vickers Cylinders Series TQ Agricultural Cylinders Nominal Pressure: 500 psi Released 10 91 113A Series TQ Hydraulic Cylinders Designed for Agricultural Applications Features Working pressure to 500 psi
ML SERIES. Double-Acting Hydraulic Valve Actuator. Thrusts up to 1,500,000 lbs SIL-3 Capable GT3 Triple Seal Gland for Severe Service Applications
Actuation Solutions and Systems for the World s Most Challenging nvironments ML SRIS Double-Acting Hydraulic Valve Actuator Designed & ngineered for Severe-Service Applications Thrusts up to 1,500,000
Bimba Original Line - Stainless Steel Body Air Cylinders
Bimba Original Line - Stainless Steel Body Air Cylinders How to Order The model number of all Original Line cylinders consists of three alphanumeric clusters. These designate product type, bore size and
MEDIUM DUTY HYDRAULIC NFPA STYLE 1 1/2 TO 8 BORE AIR 250 PSI HYDRAULIC 1500 PSI
AIR CYLINDERS & MEDIUM DUTY HYDRAULIC NFPA STYLE 1 1/2 TO 8 BORE AIR 250 PSI HYDRAULIC 1500 PSI CONSTRUCTION FEATURES 1. Rod Wiper Urethane 90A 65 to +220F, large cross section lip type wiper designed
AIR-MITE AIR-MITE DEVICES, INC W. MONTROSE AVENUE CHICAGO, ILLINOIS PHONE: 773/ FAX: 773/
CATALOG NO. 97 PNEUMATIC AUTO M ATION COMPONENTS AIR-MITE 4739 W. MONTROSE AVENUE CHICAGO, ILLINOIS 60641 PHONE: 773/286-3393 FAX: 773/286-4703 introduction Air Power, the harnessed servant of industrial
NEN Series NFPA Aluminum Cylinders
NEN Series NP luminum ylinders 1-1/2" to 4" bore sizes ompetitively priced Magnetic piston standard djustable cushion standard Sleeve nut construction standard Stocked strokes Technical data Medium: iltered
LF90C thru current printed 7/19/2012 Page 1 of 5
Drill Serial Number Range: LF90C 2011 001 thru current For Drill Build: DRILL MODULE, LF90C (3549226 Rev: D) Document Number: 5400780 Rev. A Effective Date: 1 Jan 2011 KIT SUMMARY 1 102629 KIT, BASE FRAME
Table of Contents ISO
Table of Contents ISO 6432...3-12 Features and Benefits...3 How to Order....4 Dimensions Single Rod End, Single and Double Acting...5 Single and Double Acting-Double Rod...6 Mounting Accessories...7-10
SERIES BCZ2D NOZZLE CYLINDER START-UP AND INFORMATION SHEET
Model Number Definition SERIES BCZD NOZZLE CYLINDER START-UP AND INFORMATION SHEET IMPORTANT INFORMATION DO NOT DISCARD! Use this information sheet to assist with cylinder installation, setup and repair.
Drill Serial Number Range: LF90C thru current
Drill Serial Number Range: LF90C- 2011-001 thru current For Drill Build: DRILL MODULE, LF90C (3549226 Rev: D) Document Number: 5400780 Rev. B Effective Date: 1- Jan- 2011 KIT SUMMARY 1 102629 KIT, BASE
Heavy Duty 3500/5000. psi rating. series. hydraulic cylinders. bulletin 0207XH
3500/5000 psi rating Heavy Duty series XH hydraulic cylinders bulletin 0207XH www.royalcylinders.com 1 Contents Page Description 1 Contents 2 Features Description Mounting Dimensions 3 C Clevis Mount 3
SERIES HH (NFPA) CYLINDER
HH SERIES TAB 5 Floating Rod Bushing SELF ALIGNMENT FEATURE Rod Bushing is designed to float.002 to improve bearing surface alignment. SERIES HH (NFPA) CYLINDER HH Rod Lock Reduces cylinder drag and erratic
Table of Contents Tiny Titan Series Features and Benefits How to Order Optional Features
Table of Contents Tiny Titan Series. 3-22 Features and Benefits.................. 3 How to Order......................... 4 Optional Features..................... 5 Basic and Front Flange Mounts..........
D5 & 10-5 SERIES AIR OPERATED LIQUID PUMPS
D & 1- SERIES AIR OPERATED LIQUID PUMPS PRESSURE RATIO OLD & NEW PART NUMBERS In the mid 199 s with the advent of a new inventory and computer system, SC Hydraulic Engineering was forced to change the
AIR AND HYDRAULIC CYLINDERS NFPA INDUSTRIAL TYPE
AIR AND HYDRAULIC CYLINDERS NFPA INDUSTRIAL TYPE NFPA Industrial Type Cylinders TaskMaster Pneumatic Cylinders (to 200 psi) 1 1/2" - 4" Bores 5" & 6" Bores Profile Design External Tie Rods PowerMaster
Duty Types and Forces
Types and Forces Threaded Body Metric Cylinders cting Compact Cylinders, End s: mm, mm, and mm Threaded Body Metric Cylinders TB series cylinders are single acting. Their single port is located at the
RL-H80 PARTS LIST # H USE THIS PARTS LIST FOR: Hoist Serial Number 2733 to
RL-H80 PARTS LIST # 102837H USE THIS PARTS LIST FOR: Hoist Serial Number 2733 to For older hoists use the following: Parts List No. 102837G for Serial Number 2485 to 2732 IF YOUR HOIST DOES NOT FALL WITHIN
A SERIES. Heavy-Duty Pneumatic Cylinders Pressure Rating 250 PSI
A SERIES Heavy-Duty Pneumatic Cylinders Pressure Rating 250 PSI 1, 2, 6, 43 Heads, Caps, Retainers, Mountings The heads, retainers, and mountings, are machined from steel. The trunnion head, flanges and
AZ Cylinder. Specifications. Features: Features Type ISO 6431 VDMA CETOP RP43P. Ø32mm - 100mm ISO 6431 VDMA CETOP RP43P.
Specifications Features Type ISO 6431 VDM 24562 CTOP P43P Series Z Configurations Z Double cting, Single od, Magnetic Piston, Cushions ZD Double cting, Double od, Magnetic Piston Construction Materials
Your Global Flow Control Partner. Series 92/93 Pneumatic Actuators. Technical Manual
Your Global Flow Control Partner Series 92/93 Technical Manual TM-1056 Pneumatic Actuator - 04/18/2017 Bray Series 92/93 Technical Manual - Table of Contents Topic...Page(s) Actuator Installation Notes...
Stainless Steel Air Cylinders. Series SA
Stainless Steel Air Cylinders aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding In line with our policy of continuing
AIR DRIVEN HIGH PRESSURE HYDRAULIC PUMPS & POWER UNITS
AIR DRIVEN HIGH PRESSURE HYDRAULIC PUMPS & POWER UNITS . orporated was formed in California to specialize in the supply of air driven high pressure hydraulic pumps and power units to customers located
P2 Pathwinder Conveyor. Pivoting Structure. Clamp/Support Guide. Coated Spring Steel
FLEX END ASSEMBLY Upper Tower Pivoting Structure Flex Track Multiple Distribution Discharge Points Drive Structure Clamp/Support Guide Flex Track Track Lower Tower Coated Spring Steel Illustration shows
Series HOL-W Welded Construction Hydraulic Cylinders
Series HOL-W Welded Construction Hydraulic Cylinders Description Series HOL-W hydraulic cylinders are available in Industrial and Marine specifications, they are of a heavy duty welded construction and
Flat SquareFlat Flat SquareFlat FO2, FO3, FO4(multiple power)
Flat Cylinders Flat-1 2.3-2.11 SquareFlat-1 2.12-2.18 Flat-11 2.19-2.23 SquareFlat-11 2.24-2.28 FO2, FO3, FO4(multiple power) 2.29-2.34 FOP(multiple position) 2.35-2.41 Flat Accessories 2.42-2.43 EF1 Cylinders
HYDROSTATIC TEST SYSTEM MANUAL
PDQC HYDROSTATIC TEST SYSTEM MANUAL Technical Specification Operating Instructions Part List Revised 12-2016 Manual # PDQC- 6,000 And PDQC-10,000 1 PDQC PERFORMANCE DATA Model Number Maximum Pressure Volume
Cylinders HD1 Cylinders
Cylinders HD Cylinders Cylinders For Abusive Conditions Operating Parameters Reference Control Valves Cylinders Specialty Valves Production Devices Index Combining NFPA dimensional interchangeability and
Plumbing. Controls, Drains, Piping, Flanges, Couplings, Caps and Plugs
Plumbing Hale offers a wide variety of plumbing components to make the pump installation and operation easier for the OEM and End User. Hale controls allow for a clean and compact pump panel. Controls
Angular and Parallel Grippers
CAP0551_Grippers_R2.qxp:OEM_TA 2/8/17 2:16 PM Page ii Angular and Parallel Grippers Table of Contents: Grippers Angular Grippers, Parallel Grippers and Options & Accessories Angular Grippers Introduction...
SERIES BCS STRETCH ROD CYLINDERS
BCS y Q ua lit Support SOLUTIONS for the Plastic Bottle Blowing Industry DIRECT REPLACEMENT FOR SIDEL SERIES AND SERIES MACHINES P U O C PACK TI A S y er iv el D ENTS GR N O G COM P IN G SERIES BCS STRETCH
4050A. Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies
4050A Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies Parts Identification READ these instructions before placing unit in service KEEP these and other materials
SAE FLANGES V C. Specialists in VESCOR. Hydraulic Reservoirs and Accessories
SAE FLANGES V C VESCOR Specialists in Hydraulic Reservoirs and Accessories V C TABLE OF CONTENTS V C General Information / Split Flange Clamp............................page 1 Welding Information / Simplified
Stainless steel Cylinders Series 90
90 S E R I E S Catalogue 200 Stainless steel Cylinders Series 90 DIN/ISO 643 Single and double-acting (magnetic) ø 32, 40, 50, 63, 80, 00 and 25 cushioned Stainless steel cylinders Series 90 ø 32, 40,