Removing and installing parts of the lubrication system Removing and installing parts of the lubrication system
|
|
- Julianna Little
- 5 years ago
- Views:
Transcription
1 Side 1 av 15 Removing and parts of the lubrication system Removing and parts of the lubrication system Notes: If large quantities of metal particles or other deposits (caused, for example, by partial seizure of the crankshaft or conrod bearings) are found in the engine oil when performing repairs, clean the oil passages thoroughly and renew the oil cooler in order to prevent further damage from occurring later. The oil level must not be above the max. mark - danger of damage to catalyst! Checking oil pressure => Page Oil system capacity1): Without oil filter 5.0 ltrs. With oil filter 5.5 ltrs. 1) Up-to-date figures: => "Emission and idling test" binder Engine oil specification: Vehicles without long-life service Naturally aspirated Diesel (engine codes AAB, AJA): Only use engine oil conforming to VW standard , , , or or multi-grade oil to ACEA B3/B4. Turbo Diesel (engine codes ACV, AJT, AHY, AUF): Only use engine oil conforming to VW standard or Engine oil specification: Vehicles05.99 with long-life service Only use engine oil conforming to VW standard or Note: Engine oils conforming to VW standard or can be used furthermore. The oil must then be changed every 12 months or every 15,000 km and the service interval display must be programmed correspondingly. Procedure: => Maintenance manual I =>Page 17-4 II =>Page 17-10
2 Side 2 av 15 Part I Nm + 1/2 turn (180 ) further Renew Threads and shoulder must be free of oil and grease Counterhold with T10025 to loosen and tighten Removing,
3 Side 3 av 15 and tensioning camshaft toothed belt=> Page Nm + 1/4 turn (90 ) further Ribbed belt Mark direction of rotation before removing Check for wear Remove and install with lever 3299 => Page Vibration damper with ribbed V-belt pulley When note fixing arrangement 5. Toothed belt guard - upper part 6. Camshaft toothed belt Mark D.O.R. before removing Check for wear Do not kink
4 Side 4 av 15 Removing, and tensioning: Vehicles => Page Camshaft sprocket securing bolt Observe steel type markings on bolt head: 8.8 = 85 Nm 10.9 = 100 Nm To loosen and tighten use counterhold Camshaft sprocket Note position when toothed belt: Vehicles => Page 13-45, Removing, and tensioning camshaft toothed belt Nm
5 Side 5 av Rear toothed belt guard =>Page 13-12, item Nm 12. Oil pump When note coupling ring on crankshaft => Page 17-15, item 38 Only renew complete Must be located on dowel sleeves 13. End plate 14. Oil pump Identification mark " " points in direction of end plate 15. Pressure relief valve, 40 Nm Opening pressure: bar 16. Seal Renewing => Page Crankshaft toothed belt sprocket
6 Side 6 av Tensioner Idler wheel Remove with puller 3034 and bolt 3034/1 20. Toothed belt guard - lower part 21. Vibration damper with V-belt pulley When note fixing arrangement Nm Coat threads and bolt head contact surfaces with sealing paste AMV Counter-
7 Side 7 av 15 hold with T10025 to loosen and tighten Removing, and tensioning camshaft toothed belt=> Page V-belt For alternator Check tension by thumb pressure max. deflection: new V-belt approx. 2 mm used V-belt approx. 5 mm Checking V-belt tension on vehicles with toothed rack tensioner =>Page V-belt For P.A.S vane pump Check tension by thumb pressure deflection: approx. 5 mm (new and used V- belt) Adjusting V-belt tension: => Running gear; Repair
8 Side 8 av 15 group 48; Assembly overview: vane pump, reservoir, hydraulic pipes 25. Washer Renew diamond coated Part II 1. Oil filter Loosen with strap wrench Tighten by hand Note instructions on filter when Nm 3. Oil collector 4. Oil cooler Coat contact
9 Side 9 av 15 area to flange, outside the seal, with AMV Ensure clearance to adjacent components See note => Page O-ring Renew if damaged 6. Oil filter bracket Installation position determined by dowel pin 7. Sealing ring Renew 8. Sealing plug, 40 Nm 9. Sealing plug, 20 Nm 10. Banjo bolt, 30 Nm 11. Oil supply pipe Engine codes ACV, AHY, AJT, AUF, AXG, AXL, AYC To exhaust turbocharger 12. Banjo bolt, 70 Nm 13. Cap 14. Gasket Renew if
10 Side 10 av 15 damaged 15. Dipstick The oil level must not be above the max. mark! 16. Oil filler tube Engine code: AAB, AJA Engine codes ACV, AHY, AJT, AUF, AXG, AXL, AYC with crankcase breather valve Nm bar oil pressure switch (F1), 25 Nm Only on vehicles
11 Side 11 av 15 with two oil pressure switches If sealing ring is leaking nip open and replace. Checking => Page Oil pressure retention valve 20. Adapter, 50 Nm If sealing ring is leaking nip open and replace bar oil pressure switch (F22), 25 Nm Only on vehicles with two oil pressure switches On vehicles with one oil pressure switch: 0.7 bar (F1) If sealing ring is leaking nip open and replace. Checking
12 Side 12 av 15 => Page Oil spray jet For piston cooling Nm Install with AMV Sump gasket Series production: Silicone sealant Case of repair: Gasket Renew 25. Suction pipe Clean strainer if soiled 26. Sump Clean sealing surface before Nm M8, install bolt with hexagon head to gearbox side 28. Oil seal Renew if damaged 29. Oil level/temperature sender (G266)
13 Side 13 av 15 Check => Current flow diagrams, Electrical fault finding and Fitting locations binder 30. Retaining clip Nm Nm Remove and install with socket 3249 With flywheel installed: Turn flywheel so that cutouts align with bolts 33. Spreader clip 34. Sump cover 35. Oil drain plug, 50 Nm 36. Securing plate Engine code: AAB, AJA Renew 37. Gasket Renew 38. Coupling ring For oil pump With four drive lugs Heat new coupling
14 Side 14 av 15 ring to max. 200 C before fitting 39. Guide tube For dipstick Engine codes ACV, AJT, AHY, AUF, AXG, AXL, AYC with connection for oil return pipe Nm Nm 42. Oil return pipe Engine codes ACV, AHY, AJT, AUF, AXG, AXL, AYC To exhaust turbocharger
15 Side 15 av 15
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pressure and oil pressure switch, checking Sump, removing and installing Valve gear, servicing (Page
More informationLubrication system components, removing and installing
17-1 Lubrication system components, removing and installing Note: If large quantities of metal particles or other deposits (caused, for example, by partial seizure of the crankshaft or conrod bearings)
More informationVolkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13)
13 Engine-Crankshaft, Cylinder block (Page GR-13) Engine, disassembly and assembly 10-222 A/21 guide from 10-222 A support tool, modifying Ribbed belt, removing and installing Semi-automatic toothed belt
More informationLubrication system components
17-1 Lubrication system components If you find metal shavings or large quantities of metal particles (possibly caused by partial seizure of crankshaft and connecting rod bearings) in the engine oil while
More informationLubrication system components, removing and installing
Page 1 of 33 17-1 Lubrication system components, removing and installing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once,
More informationSealing flanges and flywheel/drive plate, removing and installing
Page 1 of 20 13-47 Sealing flanges and flywheel/drive plate, removing and installing Note: For repairs to the clutch: Repair Manual, 5 Spd. Manual Transmission 012/01W Front Wheel Drive, Repair Group 30
More informationRemoving and installing cylinder head
31 30 29 28 27 26 25 24 23 22 1 2 3 11 12 10 4 9 5 6 7 8 Removing and installing cylinder head Checking compression pressure page 15-24. Notes: When installing a replacement cylinder head with a mounted
More informationRemoving and installing timing case cover. A. Engine
01-2100 Removing and installing timing case cover Operation no. of operation texts and work units or standard texts and flat rates 01-0080, 8009 A. Engine 119.960 Viscous fan clutch remove, install (20-3120).
More informationRemoving and installing cylinder head Removing, installing and tensioning toothed belt
Page 1 of 10 Removing and installing cylinder head Removing, installing and tensioning toothed belt Special tools, workshop equipment, test and measuring appliances and auxiliary items required 3359 Locking
More informationEngine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
More informationVolkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 19 Engine-Cooling system (Page GR-19)
19 Engine-Cooling system (Page GR-19) Cooling system components, removing and installing Continued coolant circulation pump (V51), checking Coolant hose connection diagram Coolant pump, removing and installing
More informationCrankshaft, Remove and Install (Engine Removed) (Z 22 SE)
Page 1 of 36 Crankshaft, Remove and Install (Engine Removed) (Z 22 SE) Remove 1. Remove the engine Note: See operation "Engine, Remove and Install". 2. Separate the manual transmission from the engine.
More informationE03 CYLINDER HEAD ASSY 1 BN0030 Dowel Pin 4
E01 FAN COVER ASSY 1 BN0061-1 Clip 1 2 150ZT-E01.02 BN0064 Fan Cover 1 3 BN0061-2 Bracket 1 4 150ZT-E01.04 BN0064-4 Carburetor Cooling Duct 1 5 150ZT-E01.05 BN0064-3 Decorative Cover 1 6 150ZT-E01.06 BN0063-2
More informationE02 CYLINDER HEAD COVER ASSY
TNG 150cc ZT E01 FAN COVER ASSY 1 BN0061-1 Clip 1 2 150ZT-E01.02 BN0064 Fan Cover 1 3 BN0061-2 Bracket 1 4 150ZT-E01.04 BN0064-4 Carburetor Cooling Duct 1 5 150ZT-E01.05 BN0064-3 Decorative Cover 1 6 150ZT-E01.06
More informationContiTech: Expert Tips for Changing Timing Belts
ContiTech: Expert Tips for Changing Timing Belts Detailed instructions for a CT1015 WP1 and CT1018K1 in an Audi A4 (B6) 2.5-liter V6 TDI with engine code AKE MY 2001 ContiTech shows how to avoid errors
More informationTiming Belt: Service and Repair Dismantling the Belt Drive. Dismantling Belt drive, dismantling Special tools: , ,
2005 Volvo XC90 L5-2.5L Turbo VIN 59 B5254T2 Page 1 Timing Belt: Service and Repair Dismantling the Belt Drive Dismantling Belt drive, dismantling Special tools: 999 5304, 999 5433, 999 5747 Note: As the
More informationgas passes through baffle plates in cylinder oil separator inlet port. Separated oil returns The first separation will happen when blowby
2 05 LAYOUT AND OVERVIEW Lubrication System PCV Oil Separator Cylinder head cover (oil + gas) Blow-by gas (air duct hose) Inlet port Oil (oil gauge pipe) The first separation will happen when blowby gas
More informationTD 3.6 L4. Parts Manual. Deutz Engine. Telescopic Handlers. Gehl RS6-34 (Tier IV) Manitou MT6034 T (Tier IV)
TD 3.6 L4 Form No. 50960088 Revision A September 04 Deutz Engine Telescopic Handlers Gehl RS6-34 (Tier IV) Manitou MT6034 T (Tier IV) Parts Manual Introduction Deutz TD 3.6 L4 The Table of Contents pages
More informationEngine Dismantle and Assemble ( )
Engine Dismantle and Assemble ( 34 8) Special Tools 5 053 Slide hammer 47 Vibration damper remover 47 5053 00 Splined head socket, cylinder head bolts 87 Mounting stand with geared drive 00 059C Installer
More informationCooling system components, removing and installing
Page 1 of 40 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate
More informationTOOTHED DRIVE BELT, REMOVING, INSTALLING AND TENSIONING
2005 Audi A4 Sedan (8E2) L4-1.8L Turbo (AMB) Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair > Removal and Replacement TOOTHED DRIVE BELT, REMOVING,
More informationENG-05, Camshaft (Timing) Belt and Balance Shaft Belt Removal
ENG-05, Camshaft (Timing) Belt and Balance Shaft Belt Removal Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Flywheel Lock (P9206) Balance Shaft
More informationMfg. No: 49T G1
Parts Manual Mfg. No: 49T877-0004-G1 Copyright Briggs and Stratton. All Rights reserved 28-Feb-2018 Model Components Table Of Contents Page Blower Housing, Air Cleaner............................................................................
More informationAccurate guidelines for longer engine life
VOLKSWAGEN VOLVO Issue 16 2013 VKMC 01270 VKMC 01258-1 VKMC 01258-2 Accurate guidelines for longer engine life Many technicians are taking chances by not following all the manufacturer recommendations
More informationPage 1 of 5 21: Drive train, B6284T S80 (-06), 1999, B6284T, 4T65EV-GT, L.H.D 17/3/2013 PRINT 21: Drive train, B6284T Replacing the Special tools: 999 5433 999 5456 Removing the Preparation Caution! the
More informationDisassembly and Assembly
SENR9973-01 September 2007 Disassembly and Assembly 400C Industrial Engine HB (Engine) HD (Engine) HH (Engine) HL (Engine) HM (Engine) HN (Engine) HP (Engine) HR (Engine) Important Safety Information Most
More informationReplacing the oil pump / front crankshaft seal
"VCC097797 EN 20100518" 1(5) Replacing the oil pump / front crankshaft seal Special tools: 998 6187, 999 5433, 999 5455, 999 5919, 999 5747, 951 2050 Note! As the illustrations in the information are used
More informationEngine, disassembling and
Page 1 of 38 13-1 Engine, disassembling and assembling Lock carrier, moving into service position Special tools and equipment 3369 support tool 1 - Bolts 2 - Bolts 3 - Bolts 4 - Bolts 5 - Bore 45 Nm (33
More informationEngine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
More informationPreventive maintenance 4
00 Series Preventive maintenance Preventive maintenance periods Use the procedures in this chapter to maintain your engine in accordance with the preventive maintenance schedule. Check the periods given
More informationRemoval. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys
Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission
More informationContiTech: Expert Tips on Replacing Timing Chains
Practical Tip ContiTech Power Transmission Group ContiTech: Expert Tips on Replacing Timing Chains Detailed instructions for a TC 1003K1 in a 1.2 l VW Polo with engine code BMD, model year 2010 ContiTech
More information1999 Acura SLX. Fig. 6: Identifying Piston & Connecting Rod Size Courtesy of ISUZU MOTOR CO.
3. Check cylinder bore to determine piston-to-cylinder clearance. Clearance should be within specification. See PISTONS, PIN & RINGS table under ENGINE SPECIFICATIONS. Fig. 6: Identifying Piston & Connecting
More information71253, XL 440H Lawn Tractor, 2008 (SN ) : BLOWER HOUSING ASSEMBLY BRIGGS AND STRATTON MODEL 31P E1 [1/
71253, XL 440H Lawn Tractor, 2008 (SN 280000001-280999999) : BLOWER HOUSING ASSEMBLY BRIGGS AND STRATTON MODEL 31P777-0133-E1 [1/ Page 1 of 50 71253, XL 440H Lawn Tractor, 2008 (SN 280000001-280999999)
More informationIllustrated Parts List to
TYPE NUMBERS 0022 through 0035, 0040 through 0062, 0070, 0076,0100, 0102, 0120 through 0125, 0307, 0318,0320, 0326, 0340 through 0366, 0370 through 0378, 0382, 0385, 0390, 0391, 0394, 0398, 0402, Illustrated
More informationDisassembly and Assembly
K EN R 623 2-00 August 2006 Disassembly and Assembly 2506-15 Industrial Engine M G A (Engine) MGB (Engine) M G D (Engine) Important Safety Information Most accidents that involve product operation, maintenance
More informationTiming Chain, Balancer Shaft, Replace (Z 22 SE)
Page 1 of 34 Timing Chain, Balancer Shaft, Replace (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release
More informationCarrier Transicold Diesel Engine CT4-91-TV (V1505) Service Parts List Rev A
Carrier Transicold Diesel Engine CT--TV (V0) Service Parts List -0 Rev A Service Parts List DIESEL ENGINE CT--TV (V0) CONTENTS INTRODUCTION... REPLACEMENT ENGINE PART NO.... ORDERING INSTRUCTIONS... GENERAL
More information1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder
Removal & Installation See VALVE SPRINGS under CYLINDER HEAD under OVERHAUL. CAMSHAFT Removal 1. Rotate crankshaft until "0" mark on flywheel aligns with timing mark on flywheel cover. Remove inspection
More informationPiston Cooling Nozzle, Replacement
Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces Service Bulletin 221-49, Piston Cooling, dated (1.2007), publication no. PV776-20177472. DService Bulletin Trucks Date Group
More informationD8 - Distributor. D9 - Auxiliary unit belts
D8 - Distributor l ubricate Lubricate the distributor shaft sparingly (1-2 drops of oil) D9 - Auxiliary unit belts check/adjust Applies to engines which do not have multi-tooth belts Check belt tension.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationCamshaft. vw-wi://rl/v.en-us.k wi:: xml?xsl=3. Special tools and workshop equipment required
Page 1 of 9 Camshaft Special tools and workshop equipment required Diesel Injection Pump Locking Pin -3359- Counterhold - Camshaft Gear -T10051- Puller - Camshaft Sprocket -T10052- Camshaft Fitting Tool
More informationService 5. Workshop Manual FABIA /55; 1.4/74 Engine - Mechanical Components Edition Service Department. Technical Information
Service 5 Workshop Manual FABIA 2000 1.4/55; 1.4/74 Engine - Mechanical Components Edition 08.99 Engine code AUA AUB BBY BBZ BKY Service Department. Technical Information Printed in Czech Republic S00.5306.00.20
More informationPrinted from MediaCat
Illustration A Crankcase Illustration A Crankcase Ref.Nr. Item code Quantity Description 1 1106 020 2506 1 Crankcase (2) 2-11 2 0000 988 5217 1 Connector (2) 3 0000 988 5200 2 Connector (2) 4 1106 641
More informationCylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
More information1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
More informationRemoving and installing toothed belt
Page 1 of 10 Special tools and workshop equipment required Diesel injection pump locking pin -3359- (2x) Pin wrench -T10020- Crankshaft stop -T10050- for engines with circular crankshaft sprocket Locking
More informationAir Filter Element, Replacing and Cleaning Housing
Air Filter Element, Replacing and Cleaning Housing Note Only use silicone-free lubricant for assembling the intake hoses. Secure all hose connections with hose clamps that match current standard production.
More informationJCB Engine Tier III Parts
GVF JCB Engine Tier III Parts 3033 Benzie Hwy. Benzonia, MI 49616 231-882-5921 Fax 231-882-5637 www.gillisons.com 800-392-6059 2 JCB TIER III ENGINE PARTS 1 MAIN INDEX TITLE PAGE NUMBER CHANGE NUMBER A
More information(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel TYPE TIGHTENING TORQUES. Rev. 2.0 OE
(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel 1 TYPE TIGHTENING TORQUES 1. Cylinder head CAUTION : (*) Follow the tightening sequence. Reference Designation (1) bolts - Throttle butterfly housing Tightening
More informationGREAVES COTTON LTD. SPARE PARTS CATALOGUE. G SERIES 3G11Tx - ENGINE GREAVES COTTON LTD.
GREAVES COTTON LTD. SPARE PARTS CATALOGUE G SERIES 3G11Tx - ENGINE GREAVES COTTON LTD. Diesel Engines Unit, Chinchwad, Pune 411019, India, Tel: (91) 20 27473564 Fax: (91) 20-27472276 Document number. P
More informationX4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY
2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 2 of 80 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3570-001 1 /P Intake,
More information6 cylinder turbocharged diesel engines for industrial applications
Perkins 2800 Models 2806C-E16 WORKSHOP MANUAL 6 cylinder turbocharged diesel engines for industrial applications Publication TSD3450E, Issue 1 Proprietary information of Perkins Engines Company Limited,
More informationTIMING CHAIN. TIMING CHAIN Removal and Installation EM-35 PFP:13028 EBS00I2X KBIA2511E
TIMING CHAIN Removal and Installation PFP:13028 EBS00I2X A EM C D E F G H I J K L M KBIA2511E EM-35 1. Camshaft sprocket (left bank EXH) 2. Camshaft sprocket (left bank INT) 3. Camshaft sprocket (right
More informationIllustrated Parts List
FORM MS 4183 10/31/2006 REPLACES FORM MS 9748 7/1997 FILE IN SECT. 2 OF SERVICE MANUAL 290700 Illustrated Parts List Model Series 290700 TYPE NUMBERS 0100, 0102, 0106, 0107, 0108, 0333, 0402, 0410. TO
More informationIllustrated Parts List to
Illustrated Parts List Vanguard Model Series 161400 to 161499 TYPE NUMBERS 0010 through 0036, 0040, 0041, 0047, 0049, 0051, 0070, 0073, 0079 through 0085, 0090, 0101, 0110 through 0135, 0199. FORM MS 9877
More informationTiming Chain - Renew ( )
«Escort 1991/1996 Table of Contents» «Group 21: Basic Engine» «Section 21-09: 2.0l DOHC 16V Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 15-030 AUniversal flange holding
More informationH132 Rear-Engine Riding Mower
Form Number H132 Rear-Engine Riding Mower Model No. 70186-260732867 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the quantity, and the description
More informationAR01.30-P-5800PK Remove/install cylinder head
Page 1 of 10 AR01.30-P-5800PK Remove/install cylinder head 7.6.00 ENGINE 111.955 in MODEL 203.045 /245 /745 P01.30-2081-09 1 Air filter housing 2 Air recirculation flap actuator 3 Top engine trim panels
More informationDisassembling and assembling transmission
27-640 Disassembling and assembling transmission Preceding work: Removing and installing transmission with torque converter (27-600). Operation number of operation texts and operation values or standard
More informationLAND ROVER GROUP / Freelander I 2.5 V6 / 09/ /2007 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.
1 Vehicle LAND ROVER GROUP / Freelander I 2.5 V6 / 09/2001-03/2007 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.5 / 130 kw Motor tag KV 6 MPI RB key LRG 48 Replacement Interval Guide
More informationService and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.
Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE
More informationCooling system components, removing and installing
19-1 Cooling system components, removing and installing Note: When the engine is warm the cooling system is under pressure. If necessary release pressure before starting repair work. Hoses are secured
More information1000 Mud Pro Model Number A2013MLW1PUSN Model Number A2013MLW1POSN - International SHARE OUR PASSION.
2013 1000 Mud Pro Model Number A2013MLW1PUSN Model Number A2013MLW1POSN - International TM SHARE OUR PASSION. TABLE OF CONTENTS 2013 ATV 1000 Mud Pro (Model No. A2013MLW1PUSN) (Model No. A2013MLW1POSN
More informationTechnical data. Part Thread (mm) Nm ±10% Tolerance Sidestand
section 3 - Torque settings Frame torque settings Sidestand Stand sensor bolt 5 Pre-applied threadlocker Stand plate fixing screw M10x25 43 Pre-applied threadlocker Side stand fastening pin Side stand
More informationIllustrated Parts Manual. Model Number A2011ICS4BUSG (Green) A2011ICS4BOSG (Green - International)
Illustrated Parts Manual 2 1 10 650 Model Number A2011ICS4BUSG (Green) A2011ICS4BOSG (Green - International) S H A R E O U R PAS S IO N. TM TABLE OF CONTENTS 2011 ATV 650 Green (Model No. A2011ICS4BUSG)
More informationCylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
More informationTiming Chain: Service and Repair
2005 Nissan-Datsun Altima L4-2.5L (QR25DE) Copyright 2013, ALLDATA 10.52SS Page 1 Timing Chain: Service and Repair TIMING CHAIN Removal and Installation Apply new engine oil to parts marked in illustration
More information1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.
DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.
More informationENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean.
REPAIRS Seal - crankshaft - rear 1. Ensure both seal location and running surface on crankshaft are clean. 1. Automatic gearbox models: converter drive plate. ENGINE - V8, REPAIRS, Plate - drive - automatic.
More information2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper
More informationATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY
2006 ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY 2006 ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 2 of 60 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-005
More informationReplacing the timing belt
"VCC116740 EN 20091209" 1(5) Replacing the timing belt Special tools: 999 5433, 999 5456 Removing the timing belt Note! As the illustrations in this service information are used for different model years
More informationHexhead Torque Values
Contents: 11: Engine 12: Engine Electrical 13: Fuel Preparation 16: Fuel Supply 17: Cooling 18: Exhaust 21: Clutch 23: Gearbox 31: Front Axle, Front Wheel Steering 32: Steering 33: Rear axle, rear-wheel
More informationDISASSEMBLY AND REASSEMBLY
24 01 DISASSEMBLY AND REASSEMBLY COMPONENTS AND SPECIAL TOOLS Injector Puller Y99220072B Glow Plug Wrench Y99220132B Fuel Pipe Wrench Sealing Caps 665 995 5844 Injector Copper Washer Puller Y99220022B
More informationATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 1 of 58 AIR INTAKE ASSEMBLY
2008 ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 1 of 58 AIR INTAKE ASSEMBLY 2008 ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 2 of 58 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description
More informationATV I l. l u. r a. Parts Manual ARCTIC CAT. 250 cc/300 cc
2000 I l l u st ATV 250 cc/300 cc Model No. A2000ATE2AUSG (250 - Green) Model No. A2000ATE2AUSR (250 - Red) Model No. A2000ATF2AUSG (300 2x4 - Green) Model No. A2000ATF2AUSR (300 2x4 - Red) Model No. A2000ATF4AUSG
More informationTiming Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: , Removal
2003 Volvo XC90 T6 AWD L6-2.9L Turbo VIN 91 B6294T Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: 999 5433, 999 5456
More informationTUNE-UP - DIESEL Isuzu Trooper II IDENTIFICATION ENGINE IDENTIFICATION TESTING ENGINE COMPRESSION ADJUSTMENTS VALVE CLEARANCE
TUNE-UP - DIESEL 1986 Isuzu Trooper II 1986 Isuzu Diesel 4 Tune-Up TUNE-UP P UP 2.2L, 2.2L Turbo, Trooper II 2.2L Turbo IDENTIFICATION ENGINE IDENTIFICATION Engine serial number is stamped on front part
More information1 of 8 1/17/2017 8:18 AM
Timing Belt Service and Repair, Removal and Replacement: Replacing... http://repair.alldata.com/alldata/article/display.action?componentid=64&... 1 of 8 1/17/2017 8:18 AM Replacing the timing belt Special
More informationIllustrated Parts List. Model Series 124T00. TYPE NUMBERS 0001 through TABLE OF CONTENTS
Illustrated Parts List Model Series 124T00 TYPE NUMBERS 0001 through 6952. TABLE OF CONTENTS FORM MS3730--Rev P--03/13/2015 REPLACES FORM MS3730--Rev N--07/11/2014 FILE IN SECT. 2 OF SERVICE MANUAL 124T00
More information1 of 11 4/11/ :35 AM
1 of 11 4/11/2015 11:35 AM Rear Disc Brake Pads Replacement Special Tools * KM-6007 Resetting Tool * KM-6007-30 Adaptor Removal Procedure 2 of 11 4/11/2015 11:35 AM Caution: Refer to Brake Dust Caution
More information650 H1 TRV EFT MODEL NUMBER A2008TBS4BETI (RED) MODEL NUMBER A2008TBS4BETM (GREEN) MODEL NUMBER A2008TBS4BETJ (CAT GREEN)
2008 650 H1 TRV EFT Illustrated Parts Manual MODEL NUMBER A2008TBS4BETI (RED) MODEL NUMBER A2008TBS4BETM (GREEN) MODEL NUMBER A2008TBS4BETJ (CAT GREEN) (VADA644AV80X05001 - VADA644AV80X05250) MORE TO GO
More informationToothed belt, removing and installing
Toothed belt, removing and installing Special Tools and Equipment ^ 3212 spanner wrench ^ 3387 pin wrench ^ T40011 pin ^ T40026 locking pin ^ T40028 socket ^ T40030 camshaft adjuster gauge Removing Lock
More informationIllustrated Parts List. Model Series. TYPE NUMBERS 0110 through TABLE OF CONTENTS
Illustrated Parts List Model Series TYPE NUMBERS 0110 through 5159. TABLE OF CONTENTS FORM MS10113 REV G 07/12/2012 REPLACES FORM MS10113 REV F 02/07/2012 FILE IN SECT. 2 OF SERVICE MANUAL Air Cleaner...
More informationIntake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
More informationReproduction. Not for. Illustrated Parts List 49E700. Model Series TYPE NUMBERS FORM MS /17/2014 FILE IN SECT. 2 OF SERVICE MANUAL 49E700
FORM MS10562 10/17/2014 FILE IN SECT. 2 OF SERVICE MANUAL 49E700 Illustrated Parts List Model Series 49E700 TYPE NUMBERS 0001. PRINTED IN U.S.A. COPYRIGHT by BRIGGS & STRATTON CORPORATION All rights reserved.
More informationIllustrated Parts List 126T00
FORM MS 3728 12/20/2007 REPLACES FORM MS 3728 09/15/2007 FILE IN SECT. 2 OF SERVICE MANUAL 126T00 Illustrated Parts List Model Series 126T00 TYPE NUMBERS 0004 through 3842. TABLE OF CONTENTS Air Cleaner.........................
More informationReproduction. Not for. Illustrated Parts List 44S700. Model Series TYPE NUMBERS 0001 THROUGH 0003, 0005, 0007, 0009, 0011, 0013 THROUGH 0020.
FORM MS10464 REV B 06/03/2016 MS10464 REV A 06/10/2015 FILE IN SECT. 2 OF SERVICE MANUAL 44S700 Illustrated Parts List Model Series 44S700 TYPE NUMBERS 0001 THROUGH 0003, 0005, 0007, 0009, 0011, 0013 THROUGH
More informationIllustrated Parts List. Model Series 31N800 TYPE NUMBERS TABLE OF CONTENTS
Illustrated Parts List Model Series 31N800 TYPE NUMBERS 0440. TABLE OF CONTENTS FORM MS--3593--04/20/2009 REPLACES FORM MS--3593--09/25/2008 FILE IN SECT. 2 OF SERVICE MANUAL 31N800 Air Cleaner... 5 Alternator...
More information1000 XT Model Number A2013AGW1PUSW Model Number A2013AGW1POSW - International SHARE OUR PASSION.
2013 1000 XT Model Number A2013AGW1PUSW Model Number A2013AGW1POSW - International TM SHARE OUR PASSION. TABLE OF CONTENTS 2013 ATV 1000 XT (Model No. A2013AGW1PUSW) (Model No. A2013AGW1POSW - International)
More informationLawn Mower. 22in Recycler. Parts Catalog. Form Number Rev A. Model No and up.
Form Number 3358-999 Rev A 22in Recycler Lawn Mower Model No. 20067-280000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the quantity, and
More information& MX Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands.
Vehicle: 1996 MAZDA 626: DX 2.0L L4 GAS-FI-N Content: Engine Service >> Timing Belt >> Timing Belt, Replace 1993-97 626 & MX-6 This engine is classified as an Interference engine. If the timing belt breaks
More informationM162 ENGINE MECHANICAL
SECTION 1B1 M162 ENGINE MECHANICAL CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed
More information2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300
Crankcase Vent Housing Removal Fig. 324: Removing & Installing Engine Vent Housing 1. Remove the hoses from the chamber. 2. Remove the chamber bolts. 3. Remove the chamber. 4. Remove the gasket material.
More informationTPD1352E, Issue 4 November User s Handbook Series EDi WK WL WM WN WP WQ WR WS
TPD1352E, Issue 4 November 2011 User s Handbook 1300 Series EDi WK WL WM WN WP WQ WR WS Thispublication iswritten in PerkinsApproved Clear English This publication is divided into six chapters: 1 General
More informationGM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions
GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions Set Includes: Locking Tool... 536594 Locking Tool... 536595 Crankshaft Holding Tool... 536596 Alignment Gauge... 536608 Belt Installation
More informationATV 300 DVX CAT GREEN (A2011KSF2BUSZ) Page 1 of 56 AIR INTAKE ASSEMBLY
2011 ATV 300 DVX CAT GREEN (A2011KSF2BUSZ) Page 1 of 56 AIR INTAKE ASSEMBLY 2011 ATV 300 DVX CAT GREEN (A2011KSF2BUSZ) Page 2 of 56 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-705
More information1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
More information