Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.
|
|
|
- Percival Russell
- 6 years ago
- Views:
Transcription
1 Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE UNDER COVER 7. SEPARATE RADIATOR HOSE NO.1 8. SEPARATE RADIATOR HOSE NO.2 9. SEPARATE OIL COOLER INLET TUBE NO SEPARATE OIL COOLER OUTLET TUBE NO REMOVE AIR CLEANER ASSEMBLY 12. REMOVE RADIATOR ASSEMBLY a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly. 13. REMOVE FAN AND GENERATOR V BELT 14. REMOVE VANE PUMP ASSEMBLY a. Remove the 2 bolts and nut, and the vane pump assembly. HINT: Vane pump assembly should be removed with the hoses connected and then hung with a rope or wire in the body's side. 15. REMOVE GENERATOR ASSEMBLY 16. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH HINT: The cooler compressor together with the magnetic clutch should be removed with the low-pressure and high-pressure hoses connected and then hung with a rope or wire in the body's side. 17. REMOVE TIMING CHAIN OR BELT COVER NO REMOVE TIMING BELT COVER SUB-ASSEMBLY N0.3 LH 19. REMOVE TIMING BELT COVER SUB-ASSEMBLY NO REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 21. REMOVE IDLER PULLEY ASSEMBLY 22. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY
2 a. Using SST, remove the pulley bolt. SST , b. Using SST, remove the crankshaft pulley. SST ( , , , , ) 23. REMOVE TIMING BELT NO.1 COVER a. Remove the 4 bats and timing belt cover. 24. REMOVE CRANKSHAFT POSITION SENSOR PLATE NO REMOVE TIMING BELT
3 a. If re-using the timing belt, check the installation marks on the timing belt. 1. Check that there are 3 installation marks on the timing belt by turning the crankshaft as shown in the illustration. If the installation marks have disappeared, place a new installation mark on the timing belt before removing each part. b. Set the No. 1 cylinder to approximately 50 BTDC/ compression. 1. Using the crankshaft damper bolt, turn the crankshaft to align the timing marks of the crankshaft timing pulley and oil pump body.
4 2. Check that the timing marks of the camshaft timing pulleys and timing belt plates aligned. If not, turn the crankshaft 1 revolution (360 ). 3. Using the crankshaft damper bolt, turn the crankshaft counterclockwise by approximately 50. NOTICE: If the timing belt is disengaged, having the crankshaft pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when you remove the camshaft timing pulley and camshaft, causing damage. So always set the crankshaft pulley at the correct angle. c. Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot.
5 d. Using SST, loosen the tension between the camshaft timing pulley (RH bank) and crankshaft timing pulley by slightly turning the camshaft timing pulley (RH bank) counterclockwise. SST ( , ) e. Disconnect the timing belt from the timing belt idler No.1, and remove the timing belt. 26. INSTALL TIMING BELT a. Check the timing belt idler No. 1 and No Visually check the seal portion of the idler pulley for oil leakage. If leakage is found, replace the idler. 2. Check that the idler turns smoothly. If necessary, replace the idler.
6 b. Check the water pump. 1. Visually check the air hole and water hole for coolant leakage. If leakage is found, replace the water pump and timing belt. 2. Turn the pulley, and check that the water pump bearing moves smoothly and quietly. If necessary, replace the water pump. c. Remove any oil or water on the crankshaft pulley, oil pump pulley, water pump pulley, idler No. 1 and idler No.2, and keep them clean. NOTICE: Only wipe the pulleys; do not use any cleansing agent. d. Set the No. 1 cylinder to TDC/compression.
7 1. Turn the hexagon wrench head portion of the camshaft to align the timing marks of the camshaft timing pulleys and timing belt plates aligned. HINT: Setting positions of the camshaft timing pulleys by turning them slightly clockwise makes it easy to install the timing belt: Camshaft timing pulley of LH bank: 1/2 teeth Camshaft timing pulley of RH bank:1 tooth 2. Using the crankshaft damper bolt, turn the crankshaft to align the timing marks of the crankshaft timing pulley and oil pump body.
8 e. Install the timing belt. 1. Remove any oil or water on the each pulley, and keep them clean. NOTICE: Only wipe the pulleys; do not use any cleansing agent. 2. Face the front mark (arrow) on the timing belt forward. 3. Connect the timing belt to the crankshaft timing pulley. Align the installation mark on the timing belt with the timing mark of the crankshaft timing pulley. 4. Connect the timing belt to the idler No Connect the timing belt to the camshaft timing pulley (LH bank). Align the installation mark on the timing belt with the timing mark of the camshaft timing pulley. 6. Connect the timing belt to the water pump pulley. 7. Connect the timing belt to the camshaft timing pulley (RH bank). Align the installation mark on the timing belt with the timing mark of the camshaft timing pulley. 8. Connect the timing belt to the idler No.1. f. Set the belt tensioner. 1. Using a press, slowly press in the push rod using 981-9,807 N (100
9 - 1,000 kgf, 220-2,205 lbs.) of pressure. 2. Align the holes of the push rod and housing, pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod. 3. Release the press. 4. Install the dust boot to the belt tensioner. g. Install the belt tensioner. 1. Temporarily install the belt tensioner with the 2 bolts. 2. Alternately tighten the 2 bolts Torque: 26 Nm (270 kgf-cm, 19 ft. lbs.) 3. Using pliers, remove the 1.27 mm hexagon wrench from the belt tensioner. h. Check the valve timing. NOTICE: Always turn the crankshaft pulley clockwise.
10 1. Using the crankshaft damper bolt,slowly turn the crankshaft pulley 2 revolutions from TDC to TDC. 2. Check that each pulley aligns with the timing marks as shown in the illustration. If the timing marks do not align, remove the timing belt and reinstall it. 3. Remove the crankshaft damper bolt. 27. INSTALL CRANKSHAFT POSITION SENSOR PLATE NO.1
11 a. Install the crank angle sensor plate as shown in the illustration. NOTICE: Take care not to install it in the wrong direction. 28. INSTALL TIMING BELT NO.1 COVER a. Install the timing belt cover with the 4 bolts. Torque: 7.5 Nm (80 kgf-cm, 66 inch lbs.) 29. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY a. Using SST and a hammer, tap in the crankshaft damper. SST b. Using SST, install the damper bolt. SST ,
12 Torque: 245 Nm (2,500 kgf-cm, 181 ft. lbs.) c. Align the damper set key with the key groove of the crankshaft damper. 30. INSTALL IDLER PULLEY ASSEMBLY a. Install the idler with the 2 bolts and 2 nuts. Torque: 16 Nm (160 kgf-cm, 12 ft. lbs.) for 12 mm head 32 Nm (330 kgf-cm, 24 ft. lbs.) for 14 mm head HINT: Each bolt length is indicated in the illustration. Bolt Length: 106 mm (4.17 inch) for 12 mm head (A) 114 mm (4.49 inch) for 14 mm head (B) 31. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY a. Install the belt tensioner with the bolt and 2 nuts. Torque: 15.5 Nm (160 kgf-cm, 11 ft. lbs.) HINT: Use a bolt 106 mm (4.18 inch) in length.
13 32. INSTALL TIMING BELT COVER SUB-ASSEMBLY NO.2 a. Fit the timing belt cover, matching the claws and pin with each part. b. Install the timing belt cover with the 2 bolts. Torque: 16 Nm (160 kgf-cm, 12 ft. lbs.) HINT: Use bolts 106 mm (4.17 inch) in length. 33. INSTALL TIMING BELT COVER SUB-ASSEMBLY N0.3 LH Torque: 7.5 Nm (80 kgf-cm, 66 inch lbs.) 34. INSTALL TIMING CHAIN OR BELT COVER NO.2 Torque: 7.5 Nm (80 kgf-cm, 66 inch lbs.) 35. INSTALL COMPRESSOR AND MAGNETIC CLUTCH a. Install the cooler compressor, stay and wire bracket with the 3 bolts and nut. Torque: 49 Nm (500 kgf-cm, 36 ft. lbs.) for bolts 29 Nm (300 kgf-cm, 21 ft. lbs.) for nuts 36. INSTALL GENERATOR ASSEMBLY 37. INSTALL VANE PUMP ASSEMBLY a. Install the vane pump assembly with the 2 bolts and nut. Alternately tighten the bolts and nut. Torque: 39.2 Nm (400 kgf-cm, 29 inch lbs.) for bolts 43.1 Nm (440 kgf-cm, 32 ft. lbs.) for nuts 38. INSTALL FAN AND GENERATOR V BELT
14 39. INSTALL RADIATOR ASSEMBLY a. Install the radiator and cooling fan assembly with the 2 upper radiator supports and 2 nuts. Torque: 13.5 Nm (135 kgf-cm, 10 ft. lbs.) 40. INSTALL AIR CLEANER ASSEMBLY Torque: 5.0 Nm (50 kgf-cm, 41 inch lbs.) 41. INSTALL AIR CLEANER INLET NO.1 Torque: 5.0 Nm (50 kgf-cm, 41 inch lbs.) 42. INSTALL INTAKE AIR CONNECTOR PIPE Torque: 5.0 Nm (50 kgf-cm, 41 inch lbs.) 43. INSTALL V-BANK COVER Torque: 5.0 Nm (50 kgf-cm, 41 inch lbs.) 44. REFILL ENGINE COOLANT 45. CHECK ENGINE COOLANT LEAK 46. INSTALL ENGINE UNDER COVER
10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.
14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE
2/17/2017 Timing Belt Service and Repair, Removal and Replacement
http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com
2000 Toyota Truck Tundra. Timing Belt: Service and Repair
Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE
EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION
EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL
REPLACEMENT. 12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 5 bolts, the engine moving control rod and the engine mounting stay.
1484 ENGINE MECHANICAL REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT WIPER ARM HEAD CAP 3. REMOVE FR WIPER ARM RH (See page 668 ) 4. REMOVE FR WIPER ARM LH (See page 668 ) 5. REMOVE COWL TOP VENTILATOR
TIMING BELT COMPONENTS EM 15
ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work
TIMING BELT (1MZ FE Jan., 2003)
14 100 TIMING BELT (1MZ FE Jan., 2003) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL RH 3. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See Pub. No. RM972U on page
12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket.
TIMING BELT (3MZFE) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FR WIPER ARM RH (See page 669) 3. REMOVE FR WIPER ARM LH (See page 669) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 669) 5.
EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION
EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be
1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION
Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002
Timing Belt: Service and Repair Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 REMOVAL 1. REMOVE OUTER FR COWL TOP PANEL ASSEMBLY 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FENDER APRON SEAL 4. REMOVE GENERATOR
INSTALLATION. NOTICE: Do not scratch the angle sensor of the timing pulley.
EM26 INSTALLATION EM11B01 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000, 0996300600) Torque:
EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE
ENGINE EG37 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZGE EG38 ENGINE 2JZ GTE ENGINE EG39 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. REMOVE BATTERY AND BATTERY TRAY
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
REMOVAL. 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY (See page CO 1 5) 4. REMOVE DRIVE BELT (See page 1) CH
ENGINE MECHANICAL (2JZGE) EM1 7 REMOVAL EM1S301 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY (See page CO 1 5) 4. REMOVE DRIVE BELT (See page 1) CH 5. REMOVE PS PUMP
Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI Timing Belt: Service and Repair
Toyota Camry CE Sedan L4-2.2L DOHC (5S-FE) MFI 2001 Timing Belt: Service and Repair REMOVAL 1. REMOVE GENERATOR 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FRONT FENDER APRON SEAL 4. REMOVE PS PUMP DRIVE BELT
EM 6 VALVE CLEARANCE ENGINE MECHANICAL EM11I 01 ADJUSTMENT HINT:
EM6 ADJUSTMENT EM11I01 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY
REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.
14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
INSTALLATION. 6. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Temporarily install the crankshaft pulley bolt to the crankshaft.
EM19 ENGINE MECHANICAL (5VZFE) INSTALLATION EM0Z003 1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley and slide on the timing pulley. (b) Slide on
REMOVAL. 16. LOOSEN CRANKSHAFT PULLEY BOLT Using SST, loosen the pulley bolt. SST ( ), EM 20 SST TIMING BELT
EM20 REMOVAL EM11901 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY 5. REMOVE NO.2 CYLINDER HEAD COVER 6. REMOVE IGNITION COILS (See
TIMING CHAIN COMPONENTS
h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:
TIMING CHAIN COMPONENTS
Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil
2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove
INSTALLATION EM 21. Inward. Sensor. Plate Washer. 10 mm Hexagon Wrench SST. Fulcrum Length SST TIMING BELT ENGINE MECHANICAL 2002 AVALON (RM872U)
Inward Sensor A05060 INSTALLATION EM21 EM0ZD02 1. INSTALL CRANKSHAFT TIMING PULLEY (a) Align the pulley set key with the key groove of the timing pulley, and slide on the timing pulley. (b) Install the
3/13/ :32 AM. NOTICE: Do not disconnect the hose.
1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install
ALLDATA Online Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15. Timing Belt Installation. Timing Belt (3S-FE)
ALLDATA Online - 1990 Toyota Camry Wagon L4-2.0L (3S-FE) - Timing Belt Installat... Page 1 of 15 Timing Belt Installation Timing Belt (3S-FE) INSTALLATION OF TIMING BELT 1. INSTALL OIL PUMP PULLEY a. Align
1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
TIMING BELT COMPONENTS
EG134 3SGTE ENGINE TIMING BELT COMPONENTS 3SGTE ENGINE EG135 EG136 3SGTE ENGINE 3SGTE ENGINE TIMING BELT REMOVAL EG137 (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
8/14/2016 8:12 PM. Bolt: Part No for Type B
1 of 21 2 of 21 REMOVAL 1. DISCONNECT PS RESERVOIR AND REMOVE RESERVOIR BRACKET 2. DISCONNECT WIRE HARNESS BRACKET FOR DLC1 3. REMOVE GENERATOR 4. REMOVE GENERATOR BRACKET 5. w/ ABS: REMOVE NO.3 ABS ACTUATOR
26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]
![26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]](/thumbs/85/92233007.jpg "26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]")
Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005
1992 Mitsubishi 3000GT VR-4
TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner
Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage.
1991 Daihatsu Truck Rocky L4-1589cc 1.6L SOHC Page 1 Timing Belt: Service and Repair Installation NOTE: Check the water pump for water leakage and the oil seal for oil leakage. Repair any water leakage
TIMING BELT (5S FE) COMPONENTS
ENGINE MECHANICAL Timing Belt (5SFE) EM67 TIMING BELT (5SFE) COMPONENTS REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20 seconds
ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)
ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See
11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.
1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.
Page 1 of 44 REPLACEMENT 1. 2. 3. 4. REMOVE ENGINE UNDER COVER RH DRAIN COOLANT (See REPLACEMENT ) REMOVE FRONT WHEEL RH REMOVE CYLINDER HEAD COVER NO. 2 a. Remove the 2 nuts, 2 clips and cylinder head
CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT
REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE
Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
TIMING BELT (3S FE) COMPONENTS
Timing Belt (3SFE) TIMING BELT (3SFE) COMPONENTS EM23 REMOVAL OF TIMING BELT 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY 2. REMOVE RH FRONT WHEEL 3. REMOVE ENGINE RH UNDER COVER 4. REMOVE CRUISE
2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
ENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
TIMING BELT (4A FE) COMPONENTS
EM30 Timing Belt (4AFE) TIMING BELT (4AFE) COMPONENTS REMOVAL OF TIMING BELT 1. REMOVE RH FRONT WHEEL 2. REMOVE RH ENGINE UNDER COVER 3. REMOVE WASHER TANK 4. LOOSEN WATER PUMP PULLEY BOLTS AND REMOVE
VALVE CLEARANCE (K3-VE)
ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT
SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.
EG45 ONVEHICLE INSPECTION 1. INSPECT OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. (a) Park the vehicle on a level spot and turn the engine off. (b) 4WD: Remove the LH front
INSTALLATION. Check that the idler pulley moves smoothly.
ENGINE MECHANICAL (5SFE) INSTALLATION EM23 EM08604 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000,
REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.
21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)
PARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2.
ENGINE MECHANICAL 1475 REPLACEMENT 141FV01 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. A66316 2. REMOVE IGNITION COIL NO.1 (a) Remove the 4 bolts and pull out
REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.
21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine
Timing Belt: Service and Repair Timing Belt Replace. Timing Belt Removal
1998 Toyota Corolla DX Sedan 4-Door L4-1762cc 1.8L DOHC MFI Page 1 Timing Belt: Service and Repair Timing Belt Replace Timing Belt Removal SPECIAL SERVICE TOOL (SST) REQUIRED ^ 09213-70010 Crankshaft Pulley
Timing Belt: Service and Repair
2000 Hyundai Sonata L4-2.4L Page 1 Timing Belt: Service and Repair REMOVAL 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 2000 Hyundai Sonata
3. Using the ST, align the Top mark on crank sprocket to nine o clock position as shown in the figure
2008 Tribeca (3.6L) MECHANICAL(H6DO) > Timing Chain Assembly Report a problem with this article INSTALLATION Be careful that the foreign matter is not into or onto assembled component during installation.
VALVE CLEARANCE (1NZ-FXE)
146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY
15.Timing Belt Assembly
MECHANICAL 15.Timing Belt Assembly A: REMOVAL 1. TIMING BELT 1) Remove the V-belt. 2) Remove the crank pulley.
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
CYLINDER HEAD (for Bank 2 4WD and Pre-Runner)
144 1GR-FE ENGINE MECHANICAL CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) ENGINE 1GR-FE ENGINE MECHANICAL COMPONENTS 88 (897, 65) x4 88 (897, 65) x4 NO. 1
1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT
1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT CAUTION: a. Do not bend or twist timing belt. b. After removing timing belt, do not turn crankshaft and
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.
EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle
Engine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
Remove four nuts, then the cooling fan assembly.
The DOHC and SOHC engines both use the same Service and Repair procedure from Isuzu. Make note that the DOHC and SOHC engines both use a single gear for the camshaft but use different alignment marks.
15.Timing Belt. Timing Belt A: REMOVAL ME(H4DOTC) TIMING BELT
15. A: REMOVAL 1. TIMING BELT 1) Remove the V-belts. 2) Remove the crank pulley. 3) Remove the timing belt cover.
DISASSEMBLY. SORENTO(BL) > 2004 > G 3.5 DOHC > Engine Mechanical System
SORENTO(BL) > 2004 > G 3.5 DOHC > Engine Mechanical System DISASSEMBLY 1. Remove the engine cover. 2. Disconnect the battery negative terminal. 3. Disconnect the radiator lower hose. 4. Disconnect the
1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.
DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.
1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1)
1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) Service and Repair Notes REMOVAL STEPS Preparation: Battery ground cable 1. Radiator upper fan shroud Remove from radiator. 2. Cooling fan assembly
2003 Hyundai Truck Santa Fe V6-3.5L
Page 1 of 12 2003 Hyundai Truck Santa Fe V6-3.5L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Page 2 of 12 REMOVAL 1. Remove the wheel of passenger side. 2. Remove the
Engine, disassembling and
Page 1 of 38 13-1 Engine, disassembling and assembling Lock carrier, moving into service position Special tools and equipment 3369 support tool 1 - Bolts 2 - Bolts 3 - Bolts 4 - Bolts 5 - Bore 45 Nm (33
Intake Manifold: Service and Repair Removal
1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS
2004 Toyota CAMRY Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS REPLACEMENT 1. REMOVE HOOD SU-ASSY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER
VALVE CLEARANCE (3ZZ FE/4ZZ FE)
ENGINE MECHANICAL ADJUSTMENT 1. REMOVE CYLINDER HEAD COVER NO.2 1487 140M901 Remove the 2 nuts, 2 clips and cylinder head cover. 2. REMOVE IGNITION COIL ASSY Disconnect the 4 connectors. (b) Remove the
VALVE CLEARANCE ADJUSTMENT EM 7
GR-FE ENGE MECHANICAL VALVE CLEARANCE VALVE CLEARANCE ADJUSTMENT 7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMAL 2. DRA ENGE COOLANT (See page CO-3) 3. ROVE V-BANK COVER (See page ES-44) 4. ROVE AIR CLEANER
Timing Belt Replacement
2004 Accord Timing Belt Replacement Report a problem with this article NOTE: The following procedure is for the installation of a new timing belt. If you are installing a used belt, refer to the timing
OIL AND FILTER INSPECTION
F 20 C 29 Recommended Viscosity (SAE): 0 18 20 7 5W30 40 4 60 16 80 27 LUBRICATION (2UZFE) 100 38 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE B16233 OIL AND FILTER OIL AND FILTER INSPECTION 1.
1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)
![4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)](/thumbs/96/128786582.jpg "4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)")
TIMING CHAIN REMOVAL/INSTALLA... < Previous Next > 2007 Mazda3 Engine TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Remove the battery cover. 2. Disconnect the negative battery cable. 3. Remove the
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing.
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. ST 499817100 ENGINE STAND Apply a coat of engine oil to the bearing and
15.Timing Belt. Timing Belt A: REMOVAL ME(STI) TIMING BELT
15.Timing Belt A: REMOVAL NOTE: Perform the work with the engine installed to body when replacing a single part. For operation procedures, refer to Timing Belt in the PM section.
11.Preparation for Overhaul
11.Preparation for Overhaul A: PROCEDURE 1) After removing the engine from body, secure it in the ST shown below. ST1 498457000 ENGINE STAND ADAPTER RH ST2 498457100 ENGINE STAND ADAPTER LH ST3 499817000
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor
REMOVAL & INSTALLATION
Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip
1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
![1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6](/thumbs/95/124411779.jpg "1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6")
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT
2002 Mitsubishi Montero Limited
Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components
Radiator Service Tool Set Hexagon Wrench Set TOYOTA Electrical Tester Set. Capacity
ENGINE EG329 PREPARATION SST (SPECIAL SERVICE TOOLS) 0923001010 Radiator Service Tool Set 0923114010 Punch 2JZGE only (Aluminum type) RECOMMENDED TOOLS 0904000010 Hexagon Wrench Set 0908200050 TOYOTA Electrical
OIL PUMP (for 4WD and Pre-Runner)
1GR-FE BRICATION OIL PUMP (for 4WD and Pre-Runner) OIL PUMP (for 4WD and Pre-Runner) ENGINE 1GR-FE BRICATION COMPONENTS 23 88 (897, 65) 88 (897, 65) NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY FRONT PROPELLER
Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) Timing Chain: Service and Repair
Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) 2002 Timing Chain: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE OIL 3. 4 WD: REMOVE FRONT DIFFERENTIAL AND DRIVE SHAFTS
REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
TIMING BELT/CHAIN AND SPROCKETS
9-82 ENGINE 4.7L DN TIMING BELT / CHAIN COVER(S) (Continued) Fig. 130 Accessory Drive Belt Tensioner 1 - TENSIONER ASSEMBLY 2 - FASTENER TENSIONER TO FRONT COVER Fig. 132 Timing Chain Cover Fasteners (4)
TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR
COOLANT COOLANT INSPECTION HINT: Check the coolant level when the engine is cold. 1. CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR The engine coolant level should be between the LOW and FULL lines at
Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L
Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt Removal Special Tools Required - Holder handle 07JAB-001020A - Holder attachment, 50 mm, offset 07MAB-PY3010A - Socket, 19 mm 07JAA-001020A
VALVE CLEARANCE ADJUSTMENT EM 8
8 1GR-FE ENGE MECHANICAL VALVE CLEARANCE VALVE CLEARANCE ADJUSTMENT 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMAL 2. DRA ENGE COOLANT (See page CO-3) 3. ROVE V-BANK COVER (See page ES-428) 4. ROVE AIR