LAND ROVER GROUP / Freelander I 2.5 V6 / 09/ /2007 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.

Size: px
Start display at page:

Download "LAND ROVER GROUP / Freelander I 2.5 V6 / 09/ /2007 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2."

Transcription

1 1 Vehicle LAND ROVER GROUP / Freelander I 2.5 V6 / 09/ /2007 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.5 / 130 kw Motor tag KV 6 MPI RB key LRG 48 Replacement Interval Guide Land Rover recommend replacement every 72,000 miles or 6 years. The previous use and service history of the vehicle must always be taken into account. Check For Engine Damage CAUTION: This engine has been identified as an INTERFERENCE engine in which the possibility of valve-to-piston damage in the event of a timing belt failure is MOST LIKELY to occur. A compression check of all cylinders should be performed before removing the cylinder head(s). Repair Times - hrs Remove & install 4,50 Special Tools Crankshaft pulley holding tool - Land Rover No.LRT Crankshaft pulley holding tool handle - Land Rover No.LRT Locking tools for camshafts - Land Rover No.LRT Alignment plate for camshaft sprockets - Land Rover No.LRT Camshaft sprocket holding tool - Land Rover No.LRT Camshaft alignment pins - Land Rover No.LRT Camshaft aligning tool - Land Rover No.LRT Timing pin - Land Rover No.LRT Special Precautions Disconnect battery earth lead. DO NOT turn crankshaft or camshaft when timing belt removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of rotation (unless otherwise stated). DO NOT turn engine via camshaft or other sprockets. Observe all tightening torques. Front Timing Belt

2 2 Removal 1. Raise and support front of vehicle. 2. Remove: Engine undershield. RH front wheel. RH splash guard. 3. Drain engine oil. 4. Support engine. 5. Remove: Engine top cover. RH engine mounting bracket. Auxiliary drive belt. Auxiliary drive belt tensioner. Auxiliary drive belt guide pulley. Alternator. LH rear timing belt cover [1]. 6. Turn crankshaft clockwise to 'SAFE' position. Ensure timing marks aligned [2]. 7. Ensure timing marks on camshaft rear sprockets aligned [3]. 8. Insert timing pin into hole in crankcase to lock flywheel [25]. Tool No.LRT NOTE: Hole for timing pin [25] is at front of engine closest to the cylinder block. 9. Remove: PAS pump pulley. PAS pump. DO NOT disconnect hoses. Engine stabiliser bar. Timing belt covers [4] & [5]. Dipstick. Dipstick tube. NOTE: Remove securing bolt. Depress dipstick tube locking collar and pull dipstick tube upwards. 10. Hold crankshaft pulley. Use tool Nos.LRT & LRT Slacken crankshaft pulley bolt [6]. 12. Remove: Crankshaft pulley bolt [6]. Crankshaft pulley [7]. Timing belt lower cover [8]. AC compressor heat shield.

3 3 AC compressor. DO NOT disconnect hoses. AC compressor bracket. Alternator bracket. Engine lifting bracket. Engine front mounting plate [9]. Rubber plug from around automatic tensioner unit. 13. Turn tensioner pulley away from belt. Use Allen key [10]. 14. Slowly compress pushrod into tensioner body until holes aligned [17]. Retain pushrod with 1,5 mm diameter pin through hole in tensioner body. NOTE: DO NOT slacken tensioner pulley bolt. 15. Remove: Automatic tensioner unit bolts [11]. Automatic tensioner unit [12]. 16. Mark direction of rotation on belt with chalk if belt is to be reused. 17. Remove timing belt. RH: NOTE: If cylinder heads are removed, water pump replaced, new camshaft sprockets fitted or if belt has been in use for more than 48,000 miles a new belt must be fitted. LH: NOTE: If cylinder heads are removed, water pump replaced, new camshaft sprockets fitted or if belt has been in use for more than km a new belt must be fitted. 18. Remove front oil seals from exhaust camshafts [13]. 19. Lock camshaft sprockets [14]. Use tool No.LRT Ensure tools located correctly on end of exhaust camshafts [15]. 21. Remove bolts from camshaft sprockets [16]. DO NOT reuse bolts. WARNING: Damage to camshafts may occur if locking tools are not installed when slackening or tightening camshaft sprocket bolts. 22. Remove: Locking tools [14]. Camshaft sprockets with hubs. Installation 1. Thoroughly clean camshaft sprockets and hubs. 2. Install hubs to camshaft sprockets. Then install both assemblies to camshafts.

4 4 3. Fit new bolts [16]. Tighten finger tight. 4. Ensure camshaft sprockets can turn freely without tilting. 5. Temporarily fit timing belt to camshaft sprockets. 6. Install locking tools to camshaft sprockets [14]. Tool No.LRT Ensure tools located correctly on end of exhaust camshafts [15]. 8. Turn camshaft sprockets fully clockwise as viewed from front of engine. 9. Ensure timing pin located correctly [25]. 10. Ensure timing marks on camshaft rear sprockets aligned [3]. 11. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 12. Use suitable wedge to hold belt in position at crankshaft sprocket. NOTE: Turn each camshaft sprocket anti-clockwise just enough to allow belt teeth to engage in sprocket. 13. Turn tensioner pulley against belt. Use Allen key [10]. 14. Install automatic tensioner unit [12]. Tighten bolts [11]. Tightening torque: 25 Nm. Use new bolts. 15. Remove Allen key from tensioner pulley [10]. 16. Remove pin from tensioner body to release pushrod [17]. 17. Fit rubber plug to automatic tensioner unit. 18. Tighten camshaft sprocket bolts [16]. Tightening torque: 27 Nm Remove locking tools from camshaft sprockets [14]. 20. Remove any wedges used to hold belt in position. 21. Remove timing pin [25]. 22. Install new oil seals on exhaust camshafts [13]. 23. Turn crankshaft slowly two turns clockwise. Ensure timing marks aligned [3]. 24. Ensure timing pin can be inserted easily [25]. 25. Remove timing pin [25]. 26. Install components in reverse order of removal. 27. Tighten crankshaft pulley bolt [6]. Tightening torque: 160 Nm. 28. Tighten sump plug. Tightening torque: 25 Nm. 29. Refill engine oil. Capacity: 5,2 litres (includes filter).

5 5 30. Tighten wheel nuts. Tightening torque: 115 Nm. Rear Timing Belts Removal NOTE: The following instructions apply to both RH and LH rear timing belts. Removal and installation should only be carried out on ONE timing belt at a time. 1. Raise and support front of vehicle. 2. Remove: Engine upper cover. Engine undershield. RH front wheel. RH splash guard. Timing belt rear cover [1]. Inlet manifold. 3. Turn crankshaft clockwise to 'SAFE' position. Ensure timing marks aligned [2]. 4. Ensure timing marks on camshaft rear sprockets aligned [3]. 5. Remove and discard front oil seal from exhaust camshaft of cylinder bank being worked on (i.e. RH or LH bank) [13]. 6. Fit alignment plate to camshaft rear sprockets [18]. Tool No.LRT Remove bolts [19]. 8. Remove camshaft sprockets, timing belt and alignment plate as an assembly [20]. 9. Remove: Alignment plate [18]. Timing belt. RH: NOTE: Mark direction of rotation on belt with chalk if belt is to be reused. If belt has been in use for more than 48,000 miles: Fit new belt. LH: NOTE: Mark direction of rotation on belt with chalk if belt is to be reused. If belt has been in use for more than km: Fit new belt. Installation 1. Thoroughly clean camshaft sprockets. 2. Place sprockets on a flat surface.

6 6 3. Ensure timing marks on camshaft sprockets aligned [3]. Ensure lugs pointing towards each other [21]. 4. Fit timing belt to sprockets. Ensure timing marks aligned [3]. 5. Fit special tool between sprockets [22]. Tool No.LRT Turn centre screw to separate sprockets until alignment plate can be fitted to camshaft sprockets [18]. Tool No.LRT Remove special tool [22]. Tool No.LRT Install alignment pins to camshafts [23]. Tool No.LRT Ensure timing marks aligned [2]. 10. Install camshaft sprockets, timing belt and alignment plate as an assembly [20]. 11. Fit aligning tool to exhaust camshaft [24]. Tool No.LRT Turn exhaust camshaft and align locating slots to sprockets. Use 30 mm socket and tool No.LRT Remove alignment pins [23]. Tool No.LRT Tighten camshaft sprocket bolts [19]. Tightening torque: 27 Nm Use new bolts. 15. Remove alignment plate [18]. Tool No.LRT Remove aligning tool [24]. Tool No.LRT Fit new oil seal [13]. 18. Turn crankshaft two turns clockwise. Ensure timing marks aligned [2] & [3]. 19. Install components in reverse order of removal. 20. Tighten wheel nuts. Tightening torque: 115 Nm.

7 7

LAND ROVER GROUP / Freelander I 2.0 Diesel / 09/ /2003 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.

LAND ROVER GROUP / Freelander I 2.0 Diesel / 09/ /2003 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2. Vehicle LAND ROVER GROUP / Freelander I 2.0 Diesel / 09/1997-09/2003 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.0 / 70-72 kw Motor tag TCie 17N,18N RB key LRG 46 Replacement Interval

More information

PEUGEOT / 206 CC 1.6i 16V / 09/ /2007 / Cabriolet Country of manufacture EU Cubic capacity/power 1.6 / 80 kw Motor tag RB key PEU 814

PEUGEOT / 206 CC 1.6i 16V / 09/ /2007 / Cabriolet Country of manufacture EU Cubic capacity/power 1.6 / 80 kw Motor tag RB key PEU 814 1 Vehicle PEUGEOT / 206 CC 1.6i 16V / 09/2000-03/2007 / Cabriolet Country of manufacture EU Cubic capacity/power 1.6 / 80 kw Motor tag NFU RB key PEU 814 Replacement Interval Guide Peugeot recommend: 206:

More information

ALLDATA Online Land Rover Freelander (LN) V6-2.5L - Camshaft Timing Belt

ALLDATA Online Land Rover Freelander (LN) V6-2.5L - Camshaft Timing Belt Page 1 of 13 Camshaft Timing Belt Service Repair No - 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt. 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash

More information

2003 Land Rover Freelander S. CAUTION: DO NOT rotate crankshaft or camshafts with timing belt removed and cylinder heads installed.

2003 Land Rover Freelander S. CAUTION: DO NOT rotate crankshaft or camshafts with timing belt removed and cylinder heads installed. FRONT TIMING BELT CAUTION: DO NOT rotate crankshaft or camshafts with timing belt removed and cylinder heads installed. Removal CAUTION: Camshaft timing belt must be replaced if cylinder head is to be

More information

Telephone: Fax: VAT Registration No.: Year: Registration:

Telephone: Fax: VAT Registration No.: Year: Registration: Telephone: Fax: VAT Registration No.: Name: Manufacturer: Renault Address: Model: Year: Registration: Tel - Private: Tel - Business: Mileage: Job number: Important note Important note The intervals and

More information

Important note. Important Note. Telephone: Fax: VAT Registration No.:

Important note. Important Note. Telephone: Fax: VAT Registration No.: Telephone: Fax: VAT Registration No.: Important note NOTE: Timing belt check and replacement intervals are subject to change at any time. To ensure that you are using the most up-to-date and accurate information

More information

Timing belt replacement intervals

Timing belt replacement intervals Important note Important note The intervals and procedures given are subject to alteration by the manufacturer at any time. Check the regularly updated Timing Belts section on our website to ensure that

More information

Timing belt replacement intervals

Timing belt replacement intervals Telephone: Fax: VAT Registration No.: Name: 1,8 66kw Manufacturer: Citroen Address: Model: Year: 1998 Registration: Tel - Private: Mileage: Tel - Business: Job number: Tel - Mobile Date Important note

More information

Important note. Important Note. Telephone: Fax: VAT Registration No.:

Important note. Important Note. Telephone: Fax: VAT Registration No.: Telephone: Fax: VAT Registration No.: Important note NOTE: Timing belt check and replacement intervals are subject to change at any time. To ensure that you are using the most up-to-date and accurate information

More information

Important note. Important Note. Telephone: Fax: VAT Registration No.:

Important note. Important Note. Telephone: Fax: VAT Registration No.: Telephone: Fax: VAT Registration No.: Important note NOTE: Timing belt check and replacement intervals are subject to change at any time. To ensure that you are using the most up-to-date and accurate information

More information

REMOVAL AND REPLACEMENT

REMOVAL AND REPLACEMENT 2002 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/36847/component/64/itype/401/nonstandard/

More information

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE HONDA 2.2L & 2.3L 4-Cylinder - DOHC & SOHC - 1990-97 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1990-94 vehicles, the manufacturer recommends camshaft and balance shaft belts be replaced at 90,000

More information

& MX Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands.

& MX Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands. Vehicle: 1996 MAZDA 626: DX 2.0L L4 GAS-FI-N Content: Engine Service >> Timing Belt >> Timing Belt, Replace 1993-97 626 & MX-6 This engine is classified as an Interference engine. If the timing belt breaks

More information

Timing Drive Components Camshaft Timing

Timing Drive Components Camshaft Timing SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner

More information

2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair

2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor

More information

Removing and installing toothed belt

Removing and installing toothed belt Page 1 of 10 Special tools and workshop equipment required Diesel injection pump locking pin -3359- (2x) Pin wrench -T10020- Crankshaft stop -T10050- for engines with circular crankshaft sprocket Locking

More information

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation. TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan

More information

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer

More information

Timing Chain - Renew ( )

Timing Chain - Renew ( ) «Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140

More information

BMW N12 PSA 1.4 / 1.6 Chain. Engine timing tools. K 10558

BMW N12 PSA 1.4 / 1.6 Chain. Engine timing tools.  K 10558 Engine timing tools BMW N12 PSA 1.4 / 1.6 Chain K 10558 www.kamasatools.com Plan Layout C A D A B Component Identification Ref OEM Ref BMW OEM Ref PSA Description A 11 9 540 0197-A3 B 11 9 540 0197-A1

More information

ENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean.

ENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean. REPAIRS Seal - crankshaft - rear 1. Ensure both seal location and running surface on crankshaft are clean. 1. Automatic gearbox models: converter drive plate. ENGINE - V8, REPAIRS, Plate - drive - automatic.

More information

VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ

VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ Telephone: 01752 667007 Fax: 01752 663399 Email: mail@volkscity.com 1 Accelerator pedal position (APP) sensor - above pedal 2 Brake pedal position (BPP)

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

2005 BMW 545i. Crank engine at central bolt in direction of rotation until drive belt is fully guided in belt pulley.

2005 BMW 545i. Crank engine at central bolt in direction of rotation until drive belt is fully guided in belt pulley. Fig. 235: Installing Special Tool On Drive Belt Crank engine at central bolt in direction of rotation until drive belt is fully guided in belt pulley. Remove special tool 64 1 040. Installation: Check

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory

More information

1999 Honda Accord DX

1999 Honda Accord DX Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are

More information

URGENT : Ensure that the precautions relating to safety and cleanliness are adhered to (refer to the brochure: RECOMMENDATIONS - PRECAUTIONS).

URGENT : Ensure that the precautions relating to safety and cleanliness are adhered to (refer to the brochure: RECOMMENDATIONS - PRECAUTIONS). PAGE 1 - b1eg1xp0 - removing - refitting timing belt removing - refitting timing belt INJECTION ES9J4S URGENT Ensure that the precautions relating to safety and cleanliness are adhered to (refer to the

More information

2002 Explorer Sport/Sport Trac Workshop Manual

2002 Explorer Sport/Sport Trac Workshop Manual Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)

More information

Tech Talk. Timing Belt 6VD1/6VE1

Tech Talk. Timing Belt 6VD1/6VE1 Holden DOHC V6 Frontera 6VD1 3.2L 1999 2004 Jackaroo 6VE1 3.5L 1998 2004 Rodeo TF 6VD1 3.2L 1998 2003 Rodeo RA 6VE1 3.5L 2003 2005 Important: Read through all the instructions before proceeding with the

More information

(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel TYPE TIGHTENING TORQUES. Rev. 2.0 OE

(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel TYPE TIGHTENING TORQUES. Rev. 2.0 OE (DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel 1 TYPE TIGHTENING TORQUES 1. Cylinder head CAUTION : (*) Follow the tightening sequence. Reference Designation (1) bolts - Throttle butterfly housing Tightening

More information

IN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256)

IN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256) 303-01A-1 IN-VEHICLE REPAIR Timing Drive Components Camshaft Drive Cassette, LH 303-01A-1 Special Tool(s) Holding Tool, Camshaft Sprocket 303-564 (T97T-6256) Adapter for 303-564 303-578 (T97T-6256-A) Holding

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)

More information

TECHNICAL SERVICE BULLETIN

TECHNICAL SERVICE BULLETIN TECHNICAL SERVICE BULLETIN SUBJECT: NO.: 09-15-93 Camshaft Timing Belt Replacement/Adjustment GROUP: Engine Service Procedure DATE: Sep.17, 1993 This Bulletin Is Supplied As Technical Information Only

More information

Removing and installing timing case cover. A. Engine

Removing and installing timing case cover. A. Engine 01-2100 Removing and installing timing case cover Operation no. of operation texts and work units or standard texts and flat rates 01-0080, 8009 A. Engine 119.960 Viscous fan clutch remove, install (20-3120).

More information

CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.

CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage. REMOVAL Timing Chain 1. Disconnect negative battery cable. 2. Drain cooling system. 3. Remove upper intake manifold. 4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.

More information

AST4950 Petrol Engine Setting/Locking Tool Kit

AST4950 Petrol Engine Setting/Locking Tool Kit AST4950 Petrol Engine Setting/Locking Tool Kit Applications: FIAT 1.2 & 1.4 8v. Petrol engines in FIAT New 500 Idea Grande Punto Linea Doblo Panda* 1.2 8v. 169A4.000, 199A4.000 1.4 8v. 350A1.000 *1.2 8v.

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns

More information

Fiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan.

Fiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan. Fiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan. Introduction This document outlines how to replace a timing belt on a Fiat X1/9 1500cc

More information

AST4950 Petrol Engine Setting/Locking Tool Kit

AST4950 Petrol Engine Setting/Locking Tool Kit AST4950 Petrol Engine Setting/Locking Tool Kit Applications: FIAT 1.2 & 1.4 8v. Petrol engines in FIAT New 500 Idea Grande Punto Linea Doblo Panda* 1.2 8v. 169A4.000, 199A4.000 1.4 8v. 350A1.000 *1.2 8v.

More information

2002 Escape Workshop Manual

2002 Escape Workshop Manual SECTION 303-01B: Engine 3.0L (4V) IN-VEHICLE REPAIR Procedure revision date: 10/09/2003 Timing Drive Components Removal CAUTION: Failure to verify correct timing drive component alignment will result in

More information

1992 Mitsubishi 3000GT VR-4

1992 Mitsubishi 3000GT VR-4 TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner

More information

Engine Dismantle and Assemble ( )

Engine Dismantle and Assemble ( ) Engine Dismantle and Assemble ( 34 8) Special Tools 5 053 Slide hammer 47 Vibration damper remover 47 5053 00 Splined head socket, cylinder head bolts 87 Mounting stand with geared drive 00 059C Installer

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS

More information

Remove four nuts, then the cooling fan assembly.

Remove four nuts, then the cooling fan assembly. The DOHC and SOHC engines both use the same Service and Repair procedure from Isuzu. Make note that the DOHC and SOHC engines both use a single gear for the camshaft but use different alignment marks.

More information

PART NO. K310. Engine Timing Tools. Renault 3.0 V6 24V.

PART NO. K310. Engine Timing Tools. Renault 3.0 V6 24V. PART NO. K310 Engine Timing Tools Renault 3.0 V6 24V www.kamasatools.com Plan Layout omponent Identification F Part No Part Number OEM Ref Description Identification A MM 23061-03 M8 x 35 H.T. Setscrew

More information

2003 Hyundai Sonata LX

2003 Hyundai Sonata LX TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate

More information

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS 2000 Suzuki Truck Grand Vitara LTD JLS 2WD V6-2.5L Vehicle > Engine, Cooling and Exhaust > Engine > Specifications > Mechanical TORQUE SPECIFICATIONS Engine Torque Specifications TORQUE COMPONENT TIGHTENING

More information

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin... Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine

More information

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover Show Timing Belt and Covers REMOVAL & INSTALLATION 1983 87 626 NOTE: For access, safely support the car, then remove the right front wheel and splash shield. 1. Loosen the alternator mounting bolts and

More information

Replacing timing belt

Replacing timing belt "VCC001207 EN 20100809" 1(5) Replacing timing belt Special tools: 998 8500, 999 5456 spark plugs cover two fuel lines clamps lift up expansion tank and place over engine to one side front timing cover

More information

Timing Drive Components ( )

Timing Drive Components ( ) Page 1 of 14 (12.65.13) Removal 1. Remove the engine front cover. For additional information, refer to For additional information, refer to. 2. Remove the spark plugs. 3. Remove the crankshaft position

More information

FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G )

FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G ) PUBLISHED: 10-OCT-2017 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G1473741) GENERAL PROCEDURES 19.90.17 HIGH PRESSURE FUEL TIMING CHECK AND

More information

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent 303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue

2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,

More information

Removal. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys

Removal. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission

More information

IMING BELT COMPONENTS REMOVAL

IMING BELT COMPONENTS REMOVAL 1 of 11 11/21/2012 2:21 PM IMING BELT COMPONENTS REMOVAL 1. Remove the wheel of passenger side. 2. Remove the side cover. 3. Remove the engine cover. 4. Disconnect the power steering hose fixing on the

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Timing Components» Timing Chain» Service and Repair» Procedures» Timing Chain and Sprockets Replacement Timing Chain and Sprockets Replacement Tools Required

More information

2003 Hyundai Truck Santa Fe V6-3.5L

2003 Hyundai Truck Santa Fe V6-3.5L Page 1 of 12 2003 Hyundai Truck Santa Fe V6-3.5L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Page 2 of 12 REMOVAL 1. Remove the wheel of passenger side. 2. Remove the

More information

Timing Belt. Removal ENGINE MECHANICAL (6VD1 3.2L) 6A-27

Timing Belt. Removal ENGINE MECHANICAL (6VD1 3.2L) 6A-27 Removal 1. Disconnect battery ground cable. 2. Remove air cleaner assembly. 3. Remove radiator upper fan shroud from radiator. 4. Move drive belt tensioner to loose side using wrench then remove drive

More information

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE MAZDA 1.6L & 1.8L 4-Cylinder - 1986-95 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1992 and earlier model years, the manufacturer recommends the belt be replaced every 60,000 miles. For 1993-95

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

Timing Belt. Removal 6A 27 ENGINE MECHANICAL (6VD1 3.2L)

Timing Belt. Removal 6A 27 ENGINE MECHANICAL (6VD1 3.2L) Removal 1.Disconnect battery ground cable. 2.Remove air cleaner assembly. 3.Remove radiator upper fan shroud from radiator. 4.Move drive belt tensioner to loose side using wrench then remove drive belt.

More information

Engine, disassembly and

Engine, disassembly and Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move

More information

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat

More information

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with

More information

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly. Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE

More information

Torque Guidelines (Z 22 SE)

Torque Guidelines (Z 22 SE) Page 1 of 14 Torque Guidelines (Z 22 SE) No. Designation Nm 1 Retaining bolts, coolant pump sprocket to coolant pump 2 Retaining bolts, balancer shaft timing chain guide rail to 3 Retaining bolts, balancer

More information

Replacing the oil pump / front crankshaft seal

Replacing the oil pump / front crankshaft seal "VCC097797 EN 20100518" 1(5) Replacing the oil pump / front crankshaft seal Special tools: 998 6187, 999 5433, 999 5455, 999 5919, 999 5747, 951 2050 Note! As the illustrations in the information are used

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and

More information

Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L

Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt Removal Special Tools Required - Holder handle 07JAB-001020A - Holder attachment, 50 mm, offset 07MAB-PY3010A - Socket, 19 mm 07JAA-001020A

More information

FUEL PUMP CAMSHAFT TIMING CHECK

FUEL PUMP CAMSHAFT TIMING CHECK PUBLISHED: 26-FEB-2018 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING CHECK (G1473740) GENERAL PROCEDURES 19.90.16 HIGH PRESSURE FUEL TIMING CHECK 5000 CC,

More information

1 of 17 2/19/ :10 AM TIMING BELT

1 of 17 2/19/ :10 AM TIMING BELT 1 of 17 2/19/2012 11:10 AM TIMING BELT 2 of 17 2/19/2012 11:10 AM INSTALLATION SPROCKET 1) Install right-hand belt cover No.2. 3 of 17 2/19/2012 11:10 AM 2) Install left-hand belt cover No.2. 3) Install

More information

2002 Mitsubishi Montero Limited

2002 Mitsubishi Montero Limited Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components

More information

General Specifications

General Specifications General Specifications Engine Data General Engine management EEC V/SEFI Emission standard 96 EEC Engine code N3A Firing order 1-3-4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cc 1998 Compression ratio

More information

2003 Cadillac CTS V6-3.2L VIN N

2003 Cadillac CTS V6-3.2L VIN N 1 of 16 5/11/2013 11:18 AM 2003 Cadillac CTS V6-3.2L VIN N Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair» Timing Belt Replacement Timing Belt Replacement Tools Required

More information

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right

More information

Timing Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket.

Timing Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket. Timing Belt Removal CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). Turn the crankshaft so that No. 1 piston is at top dead center (page 6-64). Before removing the timing belt,

More information

1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1)

1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) 1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) Service and Repair Notes REMOVAL STEPS Preparation: Battery ground cable 1. Radiator upper fan shroud Remove from radiator. 2. Cooling fan assembly

More information

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s) 303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket

More information

14-6. TSB Revision ENGINE COOLING ON-VEHICLE SERVICE

14-6. TSB Revision ENGINE COOLING ON-VEHICLE SERVICE 14-6 RADIATOR CAP DRAIN PLUG ENGINE COOLING ON-VEHICLE SERVICE When removing the radiator cap, use care to avoid contact with hot coolant or steam Place a shop towel over the cap and turn the cap counterclockwise

More information

ENGINE <6G7> Click on the applicable bookmark to selected the required model year.

ENGINE <6G7> Click on the applicable bookmark to selected the required model year. ENGINE Click on the applicable bookmark to selected the required model year. 11A-2 ENGINE CONTENTS GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 SEALANT... 4 SPECIAL TOOLS... 4 ON-VEHICLE

More information

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.

1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.

More information

Service and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3.

Service and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3. 1 of 12 5/4/2008 10:31 PM Home Account Contact ALLDATA Log Out Help METRO TOYOTA Select Vehicle New TSBs Technician's Reference 1992 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Vehicle Level Engine, Cooling

More information

IN-VEHICLE SERVICE. Engine Components

IN-VEHICLE SERVICE. Engine Components file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown

More information

Timing Belt: Service and Repair

Timing Belt: Service and Repair 2000 Isuzu Truck VehiCROSS (4WD) V6-3.5L Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Removal 1. Disconnect battery ground cable. 2. Remove air cleaner assembly. 3. Remove radiator

More information

General Specifications

General Specifications General Specifications Engine Data Description Litres Engine management EEC V/SFI Emission standard 96 EEC Engine code NSD Firing order 1-3 - 4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cm 3 1998 Compression

More information

6.0 Liter Timing Chain, Crankshaft Sprocket, Camshaft Position Actuator, and Solenoid Valve Replacement

6.0 Liter Timing Chain, Crankshaft Sprocket, Camshaft Position Actuator, and Solenoid Valve Replacement Special Tools EN 46330 Timing Belt Tensioner Retaining Pin J 8433 Two Jaw Puller J 41478 Crankshaft Front Oil Seal Installer J 41558 Crankshaft Sprocket Remover J 41665 Crankshaft Balancer and Sprocket

More information

DISASSEMBLY AND REASSEMBLY

DISASSEMBLY AND REASSEMBLY 24 01 DISASSEMBLY AND REASSEMBLY COMPONENTS AND SPECIAL TOOLS Injector Puller Y99220072B Glow Plug Wrench Y99220132B Fuel Pipe Wrench Sealing Caps 665 995 5844 Injector Copper Washer Puller Y99220022B

More information

1 of 10 2/10/2017 5:20 PM

1 of 10 2/10/2017 5:20 PM 1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft

More information

2/17/2017 Timing Belt Service and Repair, Removal and Replacement

2/17/2017 Timing Belt Service and Repair, Removal and Replacement http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com

More information

AJV8 Engine Assembly. AJV8 Engine Assembly

AJV8 Engine Assembly. AJV8 Engine Assembly AJV8 Engine Assembly Contents Cylinder Block Dowels, Plugs and Pipes 2 4 Crankshaft Bearing and Cylinder Bore Dimensions 5 9 Bearing Measuring 6 Engine Dimensions and Codes 6 7 Main Bearing Selection Chart

More information

11.Preparation for Overhaul

11.Preparation for Overhaul 11.Preparation for Overhaul A: PROCEDURE 1) After removing the engine from body, secure it in the ST shown below. ST1 498457000 ENGINE STAND ADAPTER RH ST2 498457100 ENGINE STAND ADAPTER LH ST3 499817000

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (Standard Tensioner

More information

Engine Dismantle and Assemble ( )

Engine Dismantle and Assemble ( ) Engine Dismantle and Assemble (2 34 8) Special Tools 2-036A Remover for pilot bearing 2-37 Oil seal installer/aligner 237 2036A 2-044A Installer/Aligner, Pilot Bearing/Clutch Plate 244 2-44 Inlet manifold

More information

2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300

2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300 Crankcase Vent Housing Removal Fig. 324: Removing & Installing Engine Vent Housing 1. Remove the hoses from the chamber. 2. Remove the chamber bolts. 3. Remove the chamber. 4. Remove the gasket material.

More information

Instructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines. Model No: VS4760.V3 1. SAFETY INSTRUCTIONS

Instructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines. Model No: VS4760.V3 1. SAFETY INSTRUCTIONS Instructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines Model No: VS4760.V3 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.

More information