1 of 11 4/11/ :35 AM

Size: px
Start display at page:

Download "1 of 11 4/11/ :35 AM"

Transcription

1 1 of 11 4/11/ :35 AM Rear Disc Brake Pads Replacement Special Tools * KM-6007 Resetting Tool * KM Adaptor Removal Procedure

2 2 of 11 4/11/ :35 AM Caution: Refer to Brake Dust Caution ( See: Brakes and Traction Control > Technician Safety Information > Brake Dust Caution). Caution: Refer to Brake Fluid Irritant Caution ( See: Brakes and Traction Control > Technician Safety Information > Brake Fluid Irritant Caution). Important: Brake pads on one axle must be replaced as a set. 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle ( See: Maintenance > Service Intervals). 2. Release the parking brake cable. * Release the parking brake lever. * Remove the cover of the diagnostic connection. * Remove the parking brake bellows.

3 3 of 11 4/11/ :35 AM * Release the parking brake cable by unscrewing the adjusting nut. Important: Ensure that dust sleeve between actuating lever and brake caliper is not damaged. 3. Remove the rear wheels. Refer to Tire and Wheel Removal and Installation ( See: Wheels and Tires > Removal and Replacement > Tire and Wheel Removal and Installation). Important: Ensure that dust sleeve between actuating lever and brake caliper is not damaged. 4. Remove the parking brake cable from the brake caliper. * Press the brake caliper actuating lever (1) downwards in the direction of the arrow using a screwdriver (2) and remove the parking brake cable. * Remove the retention clip (3) and pull the parking brake cable (4) out of the bracket.

4 4 of 11 4/11/ :35 AM 5. Remove the brake pads from the brake caliper. * Remove the bolt (1) from the brake caliper. Counterhold using an open-ended wrench (2). * Fold the brake caliper upwards.

5 5 of 11 4/11/ :35 AM Important: * Brake fluid level increases in brake fluid reservoir. Remove brake fluid with siphon bottle if necessary. * Ensure that the collar (arrow) of KM points towards the hand wheel or hexagonal section of KM Unscrew the brake piston. * Position KM-6007 (2) on brake caliper with KM (1). Push KM over KM * Unscrew the brake piston as far as the stop - then pull it out of the brake caliper until the next cutout (3) in the brake piston is flush

6 6 of 11 4/11/ :35 AM with the opening on the brake caliper. Important: The brake caliper must be completely removed from the brake carrier before mounting the brake pads. 7. Remove the brake caliper from the brake support. * Remove the upper bolt from the brake caliper. Counterhold using an open-ended wrench. * Remove the brake caliper from the brake carrier. Suspend it from the rear spring with a suitable wire.

7 7 of 11 4/11/ :35 AM 8. Remove the brake pads and the guide plates (1). Installation Procedure Important: Ensure that the residues of adhesive on the brake pad surfaces are removed and the surfaces cleaned afterwards. 1. Clean the guides for the brake pads in the top and bottom of the brake carrier (2) and contact surfaces with the brake pads on the brake piston (1) and the opposing surfaces (arrows). Clean the threads in the brake caliper. Important: Replace brake caliper and/or brake carrier if the brake caliper is leaking, protective cap on piston is damaged or sealing sleeve on the brake carrier is damaged. Refer to Rear Brake Caliper Replacement ( See: Brake Caliper > Removal and Replacement > Rear Brake Caliper Replacement). 2. Inspect the brake discs for wear. Refer to Brake Rotor Surface and Wear Inspection ( See: Brake Rotor/Disc > Component Tests and General Diagnostics > Brake Rotor Surface and Wear Inspection).

8 8 of 11 4/11/ :35 AM Caution: Refer to Brake Dust Caution ( See: Brakes and Traction Control > Technician Safety Information > Brake Dust Caution). Caution: Refer to Brake Fluid Irritant Caution ( See: Brakes and Traction Control > Technician Safety Information > Brake Fluid Irritant Caution). Important: The protective film (1) on the back of the brake pads must be removed after inserting the brake pads. Brake pad with mechanical wear indicator (if present) must be on the inside. 3. Insert the new metal guide sheets in the brake carrier. * Apply the special grease to the brake carrier below the metal guide sheets (marked surfaces - enlargement (1). * Insert the metal guide sheets (2) in the brake carrier.

9 9 of 11 4/11/ :35 AM 4. Insert the new brake pads in the guide plates on the brake carrier. Important: Make sure that the sheet metal guides are not bent and the adhesive surfaces of the brake linings only contact the brake caliper after they have been correctly positioned. Notice: Refer to Fastener Notice ( See: Vehicle > Vehicle Damage Warnings > Fastener Notice). 5. Install the brake caliper to the brake carrier.

10 10 of 11 4/11/ :35 AM * Place the brake caliper on the brake carrier. Slide the brake caliper exactly in the direction of the arrow, from back to front, on the brake carrier. * Install the brake caliper bolts to the brake carrier. - Clean the thread and insert the new bolts with the locking compound. - Counterhold using an open-ended wrench. Tighten the bolts to 25 N.m (18 lb ft). 6. Install the parking brake cable to the brake caliper.

11 11 of 11 4/11/ :35 AM * Install the parking brake cable to the bracket with the retaining clip (2). * Press the actuating lever (1) downwards in the direction of the arrow using a screwdriver and install the parking brake cable. 7. Install the rear wheels. Refer to Tire and Wheel Removal and Installation ( See: Wheels and Tires > Removal and Replacement > Tire and Wheel Removal and Installation). 8. Actuate the brake pedal repeatedly. 9. Start the engine. 10. Keep the brake pedal depressed for approximately 30 seconds using medium pressure. 11. Top up the brake fluid to the MAX mark. Refer to Master Cylinder Reservoir Filling ( See: Brake Master Cylinder > Procedures > Master Cylinder Reservoir Filling). 12. Adjust the parking park. Refer to Park Brake Adjustment ( See: Parking Brake System > Adjustments > Park Brake Adjustment) ALLDATA, LLC. All Rights Reserved. (Version )

Front brakes, servicing

Front brakes, servicing Page 1 / 12 46-1 Front brakes, servicing Front brakes - brake caliper Girling, servicing Note : After replacing brake pads, depress brake pedal several times firmly to properly seat brake pads in their

More information

ALLDATA Online Hummer H2 V8-6.0L - Brake Pads Replacement - Rear. Brake Pads Replacement - Rear

ALLDATA Online Hummer H2 V8-6.0L - Brake Pads Replacement - Rear. Brake Pads Replacement - Rear Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Hummer H2 V8-6.0L Conversion Calculator Vehicle Level Brakes

More information

2007 Pontiac G BRAKES Disc Brakes - G6

2007 Pontiac G BRAKES Disc Brakes - G6 REAR DISC BRAKE PADS REPLACEMENT Removal Procedure CAUTION: Refer to Brake Dust Caution. 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between

More information

Release the electrical wire from the bracket -2- toward the left -A- and remove.

Release the electrical wire from the bracket -2- toward the left -A- and remove. Page 1 of 8 Front Brake Pads, FBC-60, Removing and Installing Always replace on both axles. Special tools and workshop equipment required t Torque Wrench 5 50 Nm -V.A.G 1331- t Reversible Ratchet -V.A.G.

More information

2005 Cadillac CTS BRAKES Disc Brakes - CTS

2005 Cadillac CTS BRAKES Disc Brakes - CTS Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid

More information

2005 Cadillac CTS BRAKES Disc Brakes - CTS

2005 Cadillac CTS BRAKES Disc Brakes - CTS Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid

More information

Servicing front brakes

Servicing front brakes 46-1 Servicing front brakes C54 brake caliper, servicing Special tools and workshop equipment required VAG 1331 Torque wrench (or equivalent) VAG 1410 Torque wrench (or equivalent) VAG 1869/2 Brake pedal

More information

Notice: Refer to Adding Fluid to the Brake System Notice in the Preface section.

Notice: Refer to Adding Fluid to the Brake System Notice in the Preface section. Page 1 of 6 2008 Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: 2065646 Front Disc Brake Pads Replacement Removal Procedure Tools Required J 23738-A Hand Vacuum Pump.

More information

minimum allowable level, remove brake fluid to the midway point before proceeding.

minimum allowable level, remove brake fluid to the midway point before proceeding. 1 of 6 12/7/2011 6:45 PM aution: Refer to Brake Dust Caution in Service Precautions. Caution: Refer to Brake Fluid Irritant Caution in Service Precautions. Removal Procedure 1. Inspect the fluid level

More information

Front brakes, servicing (HP-2 dual-piston calipers - steel)

Front brakes, servicing (HP-2 dual-piston calipers - steel) Page 1 of 19 46-9 Front s, servicing (HP-2 dualpiston calipers - steel) Note: Always install complete repair kit After replacing pads and before moving vehicle, depress pedal several times firmly to properly

More information

2004 Ford Expedition

2004 Ford Expedition DISC BRAKE PADS Removal (Front) WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning

More information

Caution: Refer to Adding Fluid to the Brake System Caution in the Preface section.

Caution: Refer to Adding Fluid to the Brake System Caution in the Preface section. Page 1 of 6 2009 Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: 2094891 Rear Disc Brake Pads Replacement Special Tools J 23738-A Hand Vacuum Pump. Removal Procedure Warning:

More information

1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date:

1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date: 1988 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 025288 Date: 880711 Right Front Axle Shaft Seal - Installation Models 1986-88 Jeep Comanche,

More information

2003 Infiniti G35. CAUTION: When brake caliper is removed, DO NOT depress brake pedal, or piston will pop out.

2003 Infiniti G35. CAUTION: When brake caliper is removed, DO NOT depress brake pedal, or piston will pop out. FRONT & REAR DISC PADS CAUTION: When brake caliper is removed, DO NOT depress brake pedal, or piston will pop out. To determine which brake system vehicle is equipped with, see MODEL IDENTIFICATION. Removal

More information

1 of 9 7/19/2016 5:35 PM

1 of 9 7/19/2016 5:35 PM 1 of 9 7/19/2016 5:35 PM PADS - FRONT/REAR BRAKE - SRT8 STANDARD PROCEDURE BRAKE PAD BURNISHING CAUTION: After installing NEW brake pads, keep in mind that braking effectiveness might be somewhat reduced

More information

REMOVING AND INSTALLING THE FRONT DISC BRAKE PADS

REMOVING AND INSTALLING THE FRONT DISC BRAKE PADS Page 1 of 5 REMOVING AND INSTALLING THE FRONT DISC BRAKE PADS It is essential to observe the following points when changing brake pads. Use brake pads of the correct quality (in accordance with spare parts

More information

REAR HUB UNIT BEARING

REAR HUB UNIT BEARING 2014 Subaru Forester F4-2.5L DOHC Vehicle > Steering and Suspension > Wheels and Tires > Wheel Bearing > Service and Repair > Removal and Replacement REAR HUB UNIT BEARING Rear Hub Unit Bearing REMOVAL

More information

M-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS

M-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

2003 Jaguar X-Type BRAKES' 'Disc - X-Type

2003 Jaguar X-Type BRAKES' 'Disc - X-Type REAR DISC BRAKE CALIPER WARNING: Brake dust, if inhaled can damage your health. Always remove brake dust using a vacuum brush. Do not use a compressed air line to disperse brake dust into the atmosphere.

More information

Special tools required:

Special tools required: 34 11 000 Removing and installing/replacing brake linings on both front disk brakes Special tools required: 34 1 080 34 6 320 Necessary preliminary tasks: Remove wheels. Observe safety instructions on

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DRUM TO DISC BRAKE CONVERSION KIT A118 pre-1985 Ford F150 (except 1983-1984 w/super H/D axle) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION FRONT DISC BRAKE PADS 1. Raise and support front of vehicle. Remove wheels. Remove caliper bolt and brakeline bracket bolts. Pivot caliper aside. Remove pads and pad shim. Remove

More information

DISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed:

DISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed: Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarification. It is important to note that these instructions contain

More information

INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT

INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT INSTALLATION INSTRUCTIONS R1 REAR CONVERSION KIT INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-4 FULL FLOATING AXLE OR A130-5 (1 PIECE AXLE) Thank you

More information

1990 SUSPENSION Front ES250, LS400

1990 SUSPENSION Front ES250, LS400 SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,

More information

ALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front

ALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front Page 1 of 18 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1991 Lexus LS 400 V8-4.0L (1UZ-FE) Conversion Calculator Vehicle

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS R1 REAR DRUM TO DISC BRAKE CONVERSION KIT A130-3 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your

More information

Rear Brake Rotor Replacement

Rear Brake Rotor Replacement Page 1 of 7 2009 Pontiac G8 G8 Service Manual Suspension Rear Suspension Repair Instructions Document ID: 2094899 Rear Brake Rotor Replacement Removal Procedure Warning: Refer to Safety Glasses Warning

More information

BRAKE SYSTEM Article Text 1992 Mitsubishi Mirage For a a a a a Copyright 1998 Mitchell Repair Information Company, LLC Monday, April 01, :05AM

BRAKE SYSTEM Article Text 1992 Mitsubishi Mirage For a a a a a Copyright 1998 Mitchell Repair Information Company, LLC Monday, April 01, :05AM Article Text ARTICLE BEGINNING 1992 BRAKES Chrysler Motors/Mitsubishi - Disc & Drum Chrysler Motors: Colt, Colt 200, Colt Vista, Ram-50, Stealth, Summit, Summit Wagon; Mitsubishi: Diamante, Eclipse, Expo/Expo

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to

More information

BPW height-adjustable drawbars

BPW height-adjustable drawbars Maintenance instructions ZAV BPW BERGISCHE ACHSEN BPW height-adjustable drawbars Series ZAV REPAIR, MAINTENANCE AND OPERATING INSTRUCTIONS Maintenance and Operating Instructions ZAV Table of contents:

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION REAR BRAKE CALIPER NOTE: For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any

More information

BR 25 BRAKE HYDRAULIC BRAKE BOOSTER REMOVAL

BR 25 BRAKE HYDRAULIC BRAKE BOOSTER REMOVAL AKE HYDRAULIC AKE BOOSTER 25 REMOVAL When installing, coat the parts indicated by arrows with lithium soap base glycol grease (See page - 13). As high pressure is applied to the brake actuator tube No.

More information

SCdefault. 900 Installation instructions

SCdefault. 900 Installation instructions SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-3 1988-98 CHEVY K1500 4WD 10" DRUMS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time

More information

The following information shows the steps to change the rear brake pads and rotors on an E36 chassis.

The following information shows the steps to change the rear brake pads and rotors on an E36 chassis. 1 of 20 1/18/2010 9:15 PM See More DIY Articles Bookmark Site! The following information shows the steps to change the rear brake pads and rotors on an E36 chassis. Disclaimer: The following information

More information

PAN 17 MECHANICAL SLIDING CALLIPER DISC BRAKE ASSEMBLY AND MAINTENANCE INSTRUCTIONS

PAN 17 MECHANICAL SLIDING CALLIPER DISC BRAKE ASSEMBLY AND MAINTENANCE INSTRUCTIONS PAN 17 MECHANICAL SLIDING CALLIPER DISC BRAKE ASSEMBLY AND MAINTENANCE INSTRUCTIONS PAN 17 MECHANICAL SLIDING CALLIPER DISC BRAKE Assembly and Maintenance Instructions 2nd edition This publication is

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

Volkswagen New Beetle Brake System ABS, ABS/EDL 45 Anti-lock Brake System (ABS) (Page GR-45)

Volkswagen New Beetle Brake System ABS, ABS/EDL 45 Anti-lock Brake System (ABS) (Page GR-45) 45 Anti-lock Brake System (ABS) (Page GR-45) Anti-lock brake system (ABS) and anti-lock brake system with electronic differential lock (ABS/EDL) ITT Mark 20 IE Differences between ABS ITT Mark 20 IE and

More information

Saab 9-3 CV M04-, 4D/5D M06-

Saab 9-3 CV M04-, 4D/5D M06- SCdefault 900 Installation instructions SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Sports chassis Accessories Part No. Group Date Instruction Part

More information

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica

More information

BRAKE SYSTEM Return To Main Table of Contents

BRAKE SYSTEM Return To Main Table of Contents BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...

More information

FRONT BRAKE COMPONENTS

FRONT BRAKE COMPONENTS BR18 BRAKE SYSTEM FRONT BRAKE COMPONENTS REPLACEMENT OF BRAKE PADS HINT: If a squealing noise occurs from the front brakes while driving, check the pad wear indicator. If there are traces of the indicator

More information

Incorrect Torque Specification Front & Rear Brake Caliper Retaining Bolts & Guide Pins

Incorrect Torque Specification Front & Rear Brake Caliper Retaining Bolts & Guide Pins SERVICE XK8 DATE 2/97 TECHNICAL BULLETIN Incorrect Torque Specification Front & Rear Brake Caliper Retaining Bolts & Guide Pins MODEL VIN 206-03 1997 MY-ON XK8 Range 001001-ON Issue: The torque specifications

More information

A proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting.

A proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting. Page 1 of 21 ARTICLE BEGINNING DESCRIPTION & OPERATION WARNING: For warnings and procedures regarding vehicles equipped with Anti- Lock Brake Systems (ABS), see ANTI-LOCK BRAKE SYSTEM article in the BRAKES

More information

SECTION 4A HYDRAULIC BRAKES

SECTION 4A HYDRAULIC BRAKES SECTION 4A HYDRAULIC BRAKES Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical

More information

Removing and Installing Battery

Removing and Installing Battery ALLDATA Online - 2005 Porsche 911 GT3 (996) F6-3.6L - Removing and Installing Bat... Page 1 of 13 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's

More information

Removing/installing final drive

Removing/installing final drive 1(16) Removing/installing final drive Special tools: 998 5972, 999 5561, 999 5652, 999 5659, 999 5660 Removing Note! Position the rear lifting arms on the arrows on the sills. This is so the support arm

More information

2006 Volkswagen Phaeton

2006 Volkswagen Phaeton 27 - Vacuum hose Insert into brake booster unit Fig. 22: Connection Of Brake Lines From Dual Master Brake Cylinder To Hydraulic Unit Connection of brake lines from dual master brake cylinder to hydraulic

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A157 1991-2004 Dodge Dakota 2WD 1991-2002 Dodge Dakota 4WD 1998-2002 Dodge Durango Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for

More information

Parking brake Mechanical brake acting on rear wheels

Parking brake Mechanical brake acting on rear wheels 11 Brake System 11.1 General SPECIFICATIONS EJTC0010 Master cylinder Type Tandem type I.D. mm(in.) 20.64 mm (0.813 in.) Fluid level warning sensor Provided Brake booster Type Vacuum Boosting ratio 4.0

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W155-5 CHRYSLER 8 3 /4" & 9 3 /4" REAR AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Please take the time

More information

MAXXUS 22. Mechanical Sliding Disc Brake Caliper

MAXXUS 22. Mechanical Sliding Disc Brake Caliper MAXXUS 22 Mechanical Sliding Disc Brake Caliper MAXXUS 22 Mechanical Sliding Disc Brake Caliper Assembly Instructions/ Maintenance Guidelines Edition 1 This publication is not subject to any update service.

More information

Tools, Equipment and Supplies Needed:

Tools, Equipment and Supplies Needed: 153-162 DISC BRAKE/DUAL MASTER CYLINDER CONVERSION Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarifi cation.

More information

MAXX TM 22T MECHANICAL SLIDING CALIPER DISC BRAKE INSTALLATION AND MAINTENANCE INSTRUCTIONS

MAXX TM 22T MECHANICAL SLIDING CALIPER DISC BRAKE INSTALLATION AND MAINTENANCE INSTRUCTIONS MAXX TM 22T MECHANICAL SLIDING CALIPER DISC BRAKE INSTALLATION AND MAINTENANCE INSTRUCTIONS MAXX TM 22T Mechanical Sliding Caliper Disc Brake Installation and Maintenance Instructions Edition 1 This publication

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR CONVERSION KIT A111-2 (FORD 8" & 9" SMALL BEARING) & REAR CONVERSION KIT A111-3 (FORD 9 TORINO) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking

More information

REPLACEMENT 1. REMOVE FRONT WHEEL

REPLACEMENT 1. REMOVE FRONT WHEEL 3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake

More information

2011 Mercedes-Benz C350 Sport

2011 Mercedes-Benz C350 Sport Fig. 3: Identifying Seat-Back Lining, Tabs And Guides Model 207, 204.3 shown with front seat removed Fig. 4: Identifying Seat-Back Lining, Tabs And Screws Remove/install 1.1 Adjust left or right front

More information

DRAIN BRAKE FLUID NOTICE:

DRAIN BRAKE FLUID NOTICE: REAR DISC OVERHAUL Overhaul the RH side by the same procedure as the LH side. 1. REMOVE REAR WHEEL 2. DRAIN FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DRUM TO DISC BRAKE CONVERSION KIT A130 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTRUCTION FOR ASSEMBLY OF JEEP CJ SERIES W/AMC 20 REAR AXLES, 5 x 5-1/2" BOLT CIRCLE WITH A130-1 FULL FLOATING AXLE OR A130-2 (1 PIECE AXLE) Thank you for choosing STAINLESS

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FORCE 10 SPORT R1 REAR DISC CONVERSION KIT A126-50 2005-10 Chevrolet Silverado and GMC Sierra Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

Replace brake pads and discs - rear * (Volkswagen Golf )

Replace brake pads and discs - rear * (Volkswagen Golf ) Replace brake pads and discs - rear * (Volkswagen Golf 1997-2004) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR A136 REAR DRUM TO DISC BRAKE CONVERSION KIT for 1970-75 Jeep, CJ SERIES with Dana 44 flanged axle Thank you for choosing STAINLESS STEEL BRAKES CORPORATION

More information

1 of 27 7/21/2015 3:33 PM

1 of 27 7/21/2015 3:33 PM 1 of 27 7/21/2015 3:33 PM WM 489819 Removing and installing hydraulic pump - as of model year 2009 Tools Technical values Information 2 of 27 7/21/2015 3:33 PM Overview of hydraulic pump Preliminary work

More information

Service Procedure. 1. Raise the vehicle on a suitable hoist and support as necessary. 2. Remove both front tires and wheels.

Service Procedure. 1. Raise the vehicle on a suitable hoist and support as necessary. 2. Remove both front tires and wheels. Service Procedure The following procedure provides instructions for repairing a corrosion condition where the front wheel speed sensor mounts on the front wheel bearing assembly. 1. Raise the vehicle on

More information

2005 Dodge Grand Caravan

2005 Dodge Grand Caravan REMOVAL REMOVAL - REAR DISC BRAKE SHOES 1. Raise vehicle. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE). 2. Remove rear wheel and tire assemblies from vehicle. 3. Remove the caliper

More information

kit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions

kit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions InstalLation Instructions trail-safe samurai inner axle seal 300748-3-kit 1986-1995 suzuki samurai (all engines) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A120-4 & A120-5 1964-1/2-66 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to

More information

Performance Brake Caliper Guide Bushing Set Installation Guide

Performance Brake Caliper Guide Bushing Set Installation Guide Performance Brake Caliper Guide Bushing Set Installation Guide Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125-42 GM 10 & 12 Bolt Rear Axles with Staggered or non-staggered Shocks with C-Clips Thank you for choosing STAINLESS STEEL BRAKES CORPORATION

More information

FRONT WHEEL AND BRAKE DISCS. Order Job/Part Q ty Remarks Removing the front wheel and brake discs NOTE:

FRONT WHEEL AND BRAKE DISCS. Order Job/Part Q ty Remarks Removing the front wheel and brake discs NOTE: FRONT WHEEL AND BRAKE DISCS EAS00514 SIS FRONT WHEEL AND BRAKE DISCS 1 2 3 4 Order Job/Part Q ty Remarks Removing the front wheel and brake discs Remove the parts in the order listed. Place the motorcycle

More information

TOYOTA TUNDRA BIG BRAKE KIT Section I - Installation Preparation

TOYOTA TUNDRA BIG BRAKE KIT Section I - Installation Preparation TOYOTA TUNDRA 2007- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-34070 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake

More information

Installation Guide. Installing the FRK Hydraulic Compact Unit (HCU) on International School Buses TP-0913 Issued 1 Technical Bulletin

Installation Guide. Installing the FRK Hydraulic Compact Unit (HCU) on International School Buses TP-0913 Issued 1 Technical Bulletin Issued 12-08 Installation Guide Installing the FRK 08-10086 Hydraulic Compact Unit (HCU) on International School Buses Issued 1 Technical 12-08 Bulletin Hazard Alert Messages Read and observe all Warning

More information

1993 SUSPENSION Volkswagen Rear. EuroVan

1993 SUSPENSION Volkswagen Rear. EuroVan Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Rear EuroVan DESCRIPTION Suspension uses control arms and axle beam for stabilization. Control arms and axle beam are combined as one unit. Brake

More information

OVERHAUL. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder.

OVERHAUL. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. OVERHAUL COMPONENTS: See page 3232 Overhaul the RH side by the same procedures with LH side. Two types of brake pad exist; one is with slit and the other without slit. 1. REMOVE REAR WHEEL 2. DRAIN FLUID

More information

1994 Mazda MX-5 Miata. BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum BRAKES Mazda - Disc & Drum

1994 Mazda MX-5 Miata. BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum BRAKES Mazda - Disc & Drum BRAKE PEDAL FREE PLAY 1994 Mazda MX-5 Miata DESCRIPTION & OPERATION BRAKE SYSTEM 1994 BRAKES Mazda - Disc & Drum NOTE: For information on anti-lock brake systems, see ANTI-LOCK BRAKE SYSTEM article in

More information

Outside Rear View Mirror, Remove and Install

Outside Rear View Mirror, Remove and Install 102989Outside Rear View Mirror, and file://c:\program Files\cosids\DATA\TMP\00102989.rtf.html Page 1 of 2 Outside Rear View Mirror, and 1. Move sash window downwards 2. Detach panel for front door inside

More information

Wheel bearing housing, removing and installing

Wheel bearing housing, removing and installing Page 1 of 17 40-54 Wheel bearing housing, removing and installing Removing - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit to remove trim cap. - Remove bolt for drive axle. WARNING!

More information

disc brake axle with WABCO calipers

disc brake axle with WABCO calipers 1 2 disc brake axle with WABCO calipers 3 4 disc brake axle with WABCO calipers 5 6 disc brake axle with WABCO calipers IMT axles are supplied as non-cambered and are within the limits of a 2 minute negative

More information

M-4851-M8A SUPER 8.8 IRS MUSTANG AUTOMATIC PINION FLANGE KIT

M-4851-M8A SUPER 8.8 IRS MUSTANG AUTOMATIC PINION FLANGE KIT Please visit fordperformanceracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND

More information

1999 Toyota RAV BRAKES Disc & Drum - Trucks & Vans

1999 Toyota RAV BRAKES Disc & Drum - Trucks & Vans DESCRIPTION & OPERATION 1999-2000 BRAKES Disc & Drum - Trucks & Vans WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see appropriate ANTI-LOCK article.

More information

Caliper Bushing Inspection & Replacement. DB 22 Serial Number , DB 22 LT Serial Number , Manufactured after May 3rd, 2010

Caliper Bushing Inspection & Replacement. DB 22 Serial Number , DB 22 LT Serial Number , Manufactured after May 3rd, 2010 Caliper Bushing Inspection & Replacement Haldex DB 22 LT & DB 22 Modul-X Air Disc Brake DB 22 Serial Number 10180001, DB 22 LT Serial Number 10180001, Manufactured after May 3rd, 2010 This Service Bulletin

More information

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically

More information

BR 43. BRAKE HYDRAULIC BRAKE BOOSTER (w/ VSC) REMOVAL

BR 43. BRAKE HYDRAULIC BRAKE BOOSTER (w/ VSC) REMOVAL AKE HYDRAULIC AKE BOOSTER (w/ VSC) 43 REMOVAL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 20 times. As high pressure is applied to the brake

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A158 1994-97 Dodge Ram 1500 (2WD & 4WD) and REAR DISC BRAKE CONVERSION KIT A158-1 1998-01 Dodge Ram 1500 (2WD & 4WD) Thank you for choosing STAINLESS

More information

Toothed belt, removing and installing

Toothed belt, removing and installing Toothed belt, removing and installing Special Tools and Equipment ^ 3212 spanner wrench ^ 3387 pin wrench ^ T40011 pin ^ T40026 locking pin ^ T40028 socket ^ T40030 camshaft adjuster gauge Removing Lock

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KITS A112, A112-1 & A112-93 1979-93 FORD MUSTANG with 7.5" & 8.8" AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT SUM-BK1414-X 1997-2004 JEEP WRANGLER (TJ) WITH DANA 44 AXLES (non-abs) Thank you for choosing SUMMIT RACING for your braking needs. Pleases take the time

More information

PARKING BRAKES 36-1 CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 2 PARKING BRAKE LEVER... 5 LUBRICANTS... 2 PARKING BRAKE CABLE...

PARKING BRAKES 36-1 CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 2 PARKING BRAKE LEVER... 5 LUBRICANTS... 2 PARKING BRAKE CABLE... 36-1 PARKING BRAKES CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 2 LUBRICANTS... 2 ON-VEHICLE SERVICE... 3 Parking Brake Lever Stroke Check and Adjustment... 3 Parking Brake Switch Check...

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A128-4 1997-2004 JEEP WRANGLER (TJ) WITH DANA 44 AXLES (non-abs) Thank you for choosing STAINLESS STEEL BRAKES for your braking needs. Pleases take the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FX4 ELITE REAR DISC CONVERSION KITS WITH INTERNAL PARKING BRAKE A110-14, A111-25, A111-29 for FORD 8" & 9" REAR ENDS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION

More information

Service Bulletin No. 3023

Service Bulletin No. 3023 Service Bulletin No. 3023 MODEL TYPE SECTION/GROUP DATE D / E / J Series Coaches Service Information 4--Brakes Sept. 8, 2009 SUBJECT DISC PLUS EX225 BRAKE ACTUATOR TEST PROCEDURE CONDITIONS Service Information

More information

Wheel bearings, assembly overview

Wheel bearings, assembly overview Volkswagen Passat B6 - Wheel bearings, assembly overview Стр 1 из 9 40-5 Wheel bearings, assembly overview Suspension strut Multi-point socket head bolt Tip of bolt must point in direction of travel Left

More information

Dura Force Disc Brake System Service Manual

Dura Force Disc Brake System Service Manual TS 20809_a 3501 Shotwell Drive ISO/TS 16949:2002 Registered (PH): 937.743.8125 Franklin, OH 45005 www.waltheremc.com (FX): 937.743.8232 Table of Contents General Description 1 3 Fastener Torque Chart 4

More information

Suspension strut, removing and installing

Suspension strut, removing and installing Page 1 of 16 40-39 Suspension strut, removing and installing Removing - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit to remove trim cap. - Remove wheels. - Remove rubber grommets

More information

Mechanical Sliding Caliper Disc Brake. Type PAN 19-1 Assembly and Maintenance Instructions

Mechanical Sliding Caliper Disc Brake. Type PAN 19-1 Assembly and Maintenance Instructions WABCO Mannheim Mechanical Sliding Caliper Disc Brake Type PAN 19-1 Assembly and Maintenance Instructions WABCO Radbremsen GmbH Postfach 71 02 63 D-68222 Mannheim Bärlochweg 25 D-68229 Mannheim +49 (0)6

More information

for filling and bleeding hydraulic disk brake systems Instruction

for filling and bleeding hydraulic disk brake systems Instruction Seite 1 von 6 Instruction All processes described in this instruction are applicable for brake fluid DOT4 and hydraulic fluid based on mineral oil. Never the less the fluids must never be mixed up, otherwise

More information

OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder.

OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder. OVERHAUL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 40 times. HINT: When a pressure in power supply system is released, reaction force become

More information