USA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:

Transcription

1 SECIFICIONS D05H attern Directional Control Valves lso refer to "Directional Valve Features, Selection and Operating Recommendations" (dynexdcvoperating.pdf) CONC INFORMION US Headquarters 770 Capitol Drive ewaukee, WI U.S.. el: F: ower Units & Systems 54 Nickerson Road shland, M U.S.. el: F: ashland@dynexhydraulics.com European Sales Unit C5 Steel Close, Little End Road, Eaton Socon, Huntingdon, Cambs. E19 8 United Kingdom el: +44 (0) F: +44 (0) sales@dynexhydraulics.co.uk For more information visit our web site: ROCHURE NOES: Consult the Dynex sales department for a review of any application which requires operating above the rated flows or pressures, or higher than normal operating temperatures. Specifications shown were in effect when published. Since errors or omissions are possible, contact your sales representative for the most current specifications before ordering. Dynex reserves the right to discontinue or change designs at any time without incurring any obligation. DYNE High ressure Hydraulics Copyright ulletin dynexvesd05hspecs-0509

2 F3000 D05H SERIES, SIZE 10 DESIGN ressure Drop ( ) VLVE DESCRIION D05H valves provide high flow capability, one-third greater than D05 valves. he valve s low pressure drop is enhanced with the use of the Dynex standard subplate, which takes advantage of the valve s special double tank port design. For a description of spools, operators and application information, see dynexdcvoperating.pdf. Mounting Subplate, N.F... D05 (CEO 5) pattern, with auxiliary and Y ports for external pilot and drain. Rated Flow 30 U.S. gpm (114 L/min) nominal; 40 U.S. gpm (151 L/min) maximum for most spool types. Models with ype 56 or 58 are rated for 15 gpm (57 L/min) maximum. For higher flows, contact the sales department. Rated ressure 5000 psi (350 bar). ank ort ressure (Maximum) Standard External Drain: 5000 psi (350 bar). Internal Drain ( ID Option): Solenoid models, 1500 psi (105 bar); Solenoid models with H Option, C models, 2300 psi (160 bar), DC models, 3000 psi (210 bar); ir piloted models, 3000 psi (210 bar). Response ime (Full Stroke) Spring Centered Models: Solenoid Energized, ms. Spring Returned, ms. Spring Offset Models: Solenoid Energized, ms. Spring Returned, 85 ms. Flow Curve Reference Flow ath 6600 Series Solenoid iloted Models ilot ressure: Minimum, 65 psi (5 bar); Maximum, 5000 psi ( 350 bar). Solenoids: hese models use a D03 valve as a pilot. Models are available with standard C or DC solenoids. Optional lug-in-erminal Solenoids fit DIN Connector, Standard Form ( Hirschmann type). See dynexdcvoperating.pdf for Electrical Connections and Explosion roof Option Series Hydraulic iloted Models ilot ressure: Minimum, 100 psi (7 bar), except models with Code 5 internal operator, 85 psi (6 bar); Maximum, 3000 psi ( 210 bar). Required Volume (to shift spool full stroke): 0.21 in 3 (3,4 cm 3 ). 2 Spool ype C C C C C C E F F E D D E F F E D D C Models with ype 56 and 59 spools are rated for 15 U.S. gpm (57 L/min) maximum flow Series ir iloted Models hese models use an air piloted D03 valves as a pilot. ir ilot ressure: Minimum, 40 psi (3 bar); Maximum, 200 psi (14 bar). Required Volume (to shift spool full stroke): 0.22 in 3 (3,6 cm 3 ). VLVE EFFICIENCY Efficiency for all models is shown by the typical performance curves, above. he table identifies the appropriate pressure drop curve for each spool and flow path. For example, In the table under spool ype 5, curve is called out to determine the pressure drop for. Looking at the curves, indicates a drop of about 165 psi at 30 U.S. gpm (11,4 bar at 114 L/min). o determine total loop drop, the individual pressure drops for and (or and ) must be added.

3 F3000 D05H SERIES, SIZE 10 DESIGN INSLLION ND DIMENSIONS Valve Mounting D05H valves have a second port into a common tank passageway, for lower pressure drop. he mounting surface drawing shows the standard N.F... pattern, with auxiliary and Y ports for external pilot and drain. ort o-rings are included with valves. Mounting bolts must be ordered separately: U.N.C. hreaded x 1.00 inch (25,4 mm), Grade 8 or better, four required. Recommended mounting torque is 12 lb ft (16 N m). ilot and Drain Options he Section - drawing shows the location of the orifice for standard internal pilot, and plug for standard external drain on solenoid and air piloted models. 32 (0,80).0004/4.0 (0,010/102).18 (4,6) ORS (2),Y (66,55).093 (2,36) U.N.C. HREDED.38 DEE, 4 MOUNING HOLES E. ILO 3 (91,9) (50,80).437 (11,10).125 (3,18).656 (16,66) (26,97) (37,31) (65,07) Y E. DR..75 (19,0).43 (10,9) ORS (5).250 (6,35).844 (21,44).41 (10,4) (46,02) (32,54) (43,64) Recommended Minimum Mounting Surface, N.F... D05 (CEO 5) attern With uxiliary and Y ports and wo orts () Into Common ank assageway ORIFICE FOR INERNL ILO (SNDRD), LUG FOR EERNL ILO OION LUG FOR EERNL DRIN (SNDRD), REMOVED FOR INERNL DRIN OION Section - Solenoid Model Dimensions Dimensions are shown for both C and DC solenoids. DC configuration is shown printed in gray. he overall length of a single solenoid model (not shown) is 7.00 inches (177,8 mm) C and 7 inches (193,5 mm) DC. Single Solenoid, C, 9.3 lb (4,2 kg); DC, 9.8 lb (4,4 kg). Double Solenoid, C, 10.0 lb (4,5 kg); DC, 11.3 lb (5,1 kg) U.N.C. HREDED x 1.00 (25,4) LONG MOUNING OLS, 4 REQUIRED; ORQUE: 12 L F (16,3 N M) MNUL CUOR IN 3.91 (99,3) MIN V LVE SOLENOID FOR YE 56, 58 SOOLS; SOLENOID FOR YE 5, 6, 8, 9 SOOLS 5.69 (144,5) 2.29 (58,2) D.C (170,7) SNDRD 8.48 (215,4) WIH SCH OION CLERNCE O REMOVE COIL 1.68 (42,7).C. 1/2-14 N... SNDRD ELECRIC ENRY, 1 ECH END; REMOVE LUG, 3/8 INCH INERNL HE, FOR CCESS O HIS END 5.00 (127,0) 8.C. SOLENOID (218,9) 9.82 (249,4) D.C. SOLENOID 6600 Series, Double Solenoid iloted Models 1 MIN V L V E SOLENOID FOR YE 5, 6, 8, 9, SOOLS; SOLENOID FOR YE 56, 58 SOOLS 3

4 F3000 DO5H SERIES, SIZE 10 DESIGN Explosion roof Solenoids E solenoids with special enclosures are approved by UL and CS for use in hazardous locations. Overall length of single solenoid models (not shown) is 8.90 inches (226,1 mm). Single Solenoid, 14.3 lb (6,5 kg); Double Solenoid, 20.0 lb (9,1 kg). CLERNCE O REMOVE COIL 3.25 (82,6) 1/2-14 N... SNDRD ELECRIC ENRY, 1 ECH END; NOE SOLENOID OSIION LIMI (73.2) MNUL OVERRIDE IN 4.66 (118,4) LEDWIRES (4) YICL #18 WG ROIMELY 18 INCHES (457) LONG 1.63 (41,4) MIN VLVE SOLENOID FOR YE 56, 58 SOOLS SOLENOID FOR YE 5,6,8,9, SOOLS (317,5) GROUNDWIRE (2) YICL #18 WG (GREEN INSULION) ROIMELY 18 INCHES (457) LONG NOE: KEE IR G EWEEN SOLENOID ND VLVE ODY CLEN MIN VLVE SOLENOID FOR YE 56, 58 SOOLS SOLENOID FOR YE 5,6,8,9, SOOLS Direct Hydraulic ilot Operated s shown, these models use a crossover block to direct pilot pressure from auxiliary ports and Y. 6.0 lb (2,7 kg). and Y ort Function 6.69 (169,9) SNDRD 8.45 (214,6) WIH SCH OION U.N.C. HREDED x 1.00 (25,4) LONG MOUNING OLS, 4 REQUIRED; ORQUE: 12 L F (16,3 N M) (54,0) 6600 Series, Double E Solenoid Models 1 Model ort ort Y 681 ctuator External Drain.69 (17,5) 2.19 (55,6) 682 External Drain ctuator 685 ctuator for: ype 5, 6, 8, 9 ctuator for: ype 56, 58 ctuator for: ype 5, 6, 8, 9 ctuator for: ype 56, (93,0) ir iloted Models Overall length of single actuator configuration (not shown) is 6.24 inches (158,5 mm). Single ctuator, 8.4 lb (3,8 kg); Double ctuator, 9.1 lb (4,1 kg). ILO ORS (2) 1/8-27 N U.N.C. HREDED x 1.00 LONG (25,4) MOUNING OLS, 4 REQUIRED; ORQUE: 12 L F (16,3 N M) 6800 Series, Direct Hydraulic iloted Models MIN VLVE CUOR FOR YE 56, 58 SOOLS; CUOR FOR YE 5, 6, 8, 9, SOOLS 7.09 (180,1) 3.53 (89,7) 1 MIN VLVE CUOR FOR YE 56, 58 SOOLS; CUOR FOR YE 5, 6, 8, 9, SOOLS 1.78 (45,2) D05H SULE ND OL KIS art Number Subplates: Description 3.91 (99,3) 5.07 (128,8) SNDRD 6.83 (173,5) WIH SCH OION 1.25 (31,8) HE 22-D05H-.75 ottom orts, 3/4-14 N...F. SO22-D05H-.75 olt Kit: 22-K Side orts, 3/4-14 N...F. Four U.N.C. hreaded x 1.00 inch (25,4 mm) U.N.C. HREDED x 1.00 (25,4) LONG MOUNING OLS, 4 REQUIRED; ORQUE: 12 L F (16,3 N M) 6900 Series, Double ir iloted Models 1 4

5 F3000 D05H SERIES, SIZE 10 DESIGN YICL MODEL CODE D05H 115DF R CH Valve ype Subplate Mounted Directional Control ctuator 6 Solenoid Operated 8 Hydraulic iloted 9 ir iloted 1 2 Internal Operator wo osition: Spring Offset ( ), ctuator Offset ( ) wo osition: Spring Offset ( ), ctuator Offset ( ) 3 wo osition: ctuator Offset, Detented 4 wo osition: Spring Centered, ctuator Offset 5 hree osition: Spring Centered, ctuator Offset For most spools, normal flow is actuator offset. For Spool ypes 56 or 58, normal flow is actuator offset. 5 6 Spools D05H R H3 H3 H5 H5 C CG H M SL Valve Size N.F... D05 (CEO 5) Mounting attern with auxiliary "" port (external pilot) and "Y" port (external drain) Reverse Flow Option Reverse Flow (Code 4 Operator Only) Solenoid Options Design Number 3-pin Connector for single solenoid models on port "" end ➂ 3-pin Connector for single solenoid models on port "" end ➂ 5-pin Connector for single or double solenoid models on port "" end ➂ 5-pin Connector for single or double solenoid models on port "" end ➂ CS and UL Recognized Coils (Etched with Symbol) ➃ Modification Number Cable Grip for.38 to.44 inch (9,5 to 11,1 mm) O.D. machine tool cable High ressure ank ort: 2300 psi (160 bar) maximum C models; 3000 psi (210 bar) maximum DC models Hand ctuated Manual Override Solenoid Lights (available 115DF C only) erminal Strip Option not available with E solenoid models. Option not available with lug-in erminal solenoid models. ➂ N.F... standard ;.N.S.I. standard 93.55M ➃ vailable with 115DF solenoids only Closed Crossover Open Crossover General Options CH Flow Control (ilot Choke) 3000 psi (210 bar) maximum pressure ID Internal Drain External ilot Not available with hydraulic piloted models. Electrical Options Standard C Solenoids (Dual Frequency): Standard DC Solenoids: 24DF 24V/60Hz, 24V/50Hz 12DC 12VDC 115DF 115V/60HZ, 110V/50Hz 24DC 24VDC 230DF 230V/60Hz, 220V/50Hz 460DF 460V/60Hz, 440V/50Hz lug-in erminal C Solenoids: lug-in erminal DC Solenoids: 115H 115V/60Hz, 110V/50Hz 12HD 12VDC 230H 230V/60Hz, 220V/50Hz 24HD 24VDC Explosion-roof C Solenoids: Explosion-roof DC Solenoids: 115E 115V/60Hz 12E 12VDC 110E 110V/50Hz 24E 24VDC 220E 220V/50Hz Fits DIN Connector Standard Form ( Hirschmann type). 5