FUEL PUMP CAMSHAFT TIMING CHECK
|
|
- Tracy Reed
- 5 years ago
- Views:
Transcription
1 PUBLISHED: 26-FEB RANGE ROVER SPORT (LS), ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING CHECK (G ) GENERAL PROCEDURES HIGH PRESSURE FUEL TIMING CHECK 5000 CC, AJ V USED WITHINS SPECIAL TOOL(S) Timing Tool
2 JLR Alignment Tool, Fuel Pump Camshaft Timing PART(S) STEP PART NAME QUANTITY Check Step 14 Brake vacuum pump seal 1 Check Step 17 Oil pan drain plug 1 CHECK 1. Disconnect the battery ground cable. Refer to: Specifications ( Battery, Mounting and Cables, Specifications).
3 2. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle. 3. Refer to: Engine Undershield ( Front End Body Panels, Removal and Installation). 4.
4 5. CAUTION: Be prepared to collect escaping oil. NOTES: Discard the sealing washer. Collect the engine oil in a clean container. 6.
5 7. CAUTIONS: Only rotate the crankshaft clockwise. Make sure that the crankshaft is fully locked. Install the Special Tool(s): Using a suitable marker, mark the position of the crankshaft pulley as illustrated.
6 9. NOTE: Discard the seal. 10. Remove the Special Tool(s):
7 11. If required, carefully adjust the crankshaft position to allow correct installation of the special tool. Install the Special Tool(s): JLR
8 12. CAUTION: Do not use excessive force when adjusting the crankshaft position. NOTE: If the crankshaft timing tool cannot be installed, adjustment of the fuel pump camshaft timing will be required. If required, carefully adjust the crankshaft position to allow correct installation of the special tool. Install the Special Tool(s): If the crankshaft timing tool cannot be installed, adjustment of the fuel pump camshaft timing will be required. Refer to: Fuel Pump Camshaft Timing Adjustment ( Engine - V8 N /A 5.0L Petrol, General Procedures).
9 13. Remove the Special Tool(s): JLR NOTE: Install a new seal. Renew Part: Brake vacuum pump seal Quantity: 1. Torque: 12 Nm
10 15. Remove the Special Tool(s): Torque: 10 Nm
11 17. NOTE: Install a new sealing washer. Renew Part: Oil pan drain plug Quantity: 1. Torque: 24 Nm 18. Connect the battery ground cable. Refer to: Specifications ( Battery, Mounting and Cables, Specifications). 19. CAUTION: Make sure that the vehicle is left for 5 minutes from filling with oil and that the engine oil level is reading at least minimum (by following Steps 22-28), before starting the engine. Fill the engine with oil - for filling values on vehicles without supercharger: Refer to: Specifications ( Engine - V8 N/A 5.0L Petrol, Specifications). Fill the engine with oil - for filling values on vehicles with supercharger: Refer to: Specifications ( Engine - V8 S/C 5.0L Petrol, Specifications). Clean any residual engine oil from the oil filler cap area.
12 20. CAUTION: Make sure that the vehicle has been left for 5 minutes from filling with oil. Follow the Steps before starting the engine. 21. Start the engine and allow to run for 10 minutes, stop the engine. Check for leaks. 22. CAUTIONS: Make sure that the selector lever and the gearshift mechanism are in the park (P) position. Make sure that the hood is open. Turn the ignition on.
13 23. Press the right-hand directional button to access the instrument cluster menu. 24. Press the right-hand OK button.
14 25. Press the right-hand directional button to access the Oil Level Display.
15 26. Press the right-hand OK button and follow the instructions. 27. Press the cruise control cancel button twice within 2 seconds.
16 28. The message center display will revert to the normal display in the trip computer. Press the right-hand OK button and follow the instructions. Check that the oil level display shows an oil level reading. Only after having started and run the engine for 10 minutes (as indicated in Step 21), switch off the engine, then stabilizing for 10 minutes, take a reading from the oil level display and, if necessary top up with engine oil. 29. NOTE: If instructed to follow Steps in a previous step, return to Step 21 and continue the procedure. Turn the ignition off. 30. Allow 10 minutes for the engine oil level to stabilize if there has been additional oil top up.
17 31. NOTE: The following steps are to update the average oil level value. Turn the ignition on. Press and hold the cruise control cancel button for more than 2 seconds. 32. The message center display will revert to the normal display in the trip computer. 33. Turn the ignition off. 34. Turn the ignition on.
18 35. Press the right-hand directional button to access the instrument cluster menu. 36. Press the right-hand OK button.
19 37. Press the right-hand directional button to access the Oil Level Display.
20 38. Press the right-hand OK button and follow the instructions. Make sure that the average oil level value has now been updated. 39. Refer to: Engine Undershield ( Front End Body Panels, Removal and Installation). 40. Torque: 10 Nm
21 PUBLISHED: 10-OCT RANGE ROVER SPORT (LS), ENGINE - V8 N/A 5.0L PETROL FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G ) GENERAL PROCEDURES HIGH PRESSURE FUEL TIMING CHECK AND ADJUST 5000 CC, AJ V8, NATURALLY ASPIRATED 6.00 USED WITHINS HIGH PRESSURE FUEL TIMING CHECK AND ADJUST 5000 CC, AJ V8, SUPERCHARGED 6.70 USED WITHINS SPECIAL TOOL(S) Timing Tool
22 JLR Alignment Tool, Fuel Pump Camshaft Timing ADJUSTMENT 1. Disconnect the battery ground cable. Refer to: Specifications ( Battery, Mounting and Cables, Specifications). 2. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle. 3. Refer to: Fuel Pump Camshaft Timing Check ( Engine - V8 S/C 5.0L Petrol, General Procedures). 4. Refer to: Lower Timing Cover ( Engine - V8 N/A 5.0L Petrol, Removal and Installation). Refer to: Lower Timing Cover ( Engine - V8 S/C 5.0L Petrol, Removal and Installation).
23 5. CAUTIONS: Make sure that the area around the component is clean and free of foreign material. Inspect the 3 timing chain oil nozzles for signs of damage, install as necessary.
24 6. NOTE: Using a suitable tie strap, position the tensioner to one side. Special Tool(s): JLR Torque: 12 Nm 7. Refer to: Lower Timing Cover ( Engine - V8 N/A 5.0L Petrol, Removal and Installation). Refer to: Lower Timing Cover ( Engine - V8 S/C 5.0L Petrol, Removal and Installation).
25 8. Remove the Special Tool(s): Torque: 10 Nm 10. NOTE: Install a new sealing washer. Torque: 24 Nm
26 11. Connect the battery ground cable. Refer to: Specifications ( Battery, Mounting and Cables, Specifications). 12. CAUTION: Make sure that the vehicle is left for 5 minutes from filling with oil and that the engine oil level is reading at least minimum (by following Steps 15-21), before starting the engine. Fill the engine with oil - for filling values on vehicles without supercharger: Refer to: Specifications ( Engine - V8 N/A 5.0L Petrol, Specifications). Fill the engine with oil - for filling values on vehicles with supercharger: Refer to: Specifications ( Engine - V8 S/C 5.0L Petrol, Specifications). Clean any residual engine oil from the oil filler cap area. 13. CAUTION: Make sure that the vehicle has been left for 5 minutes from filling with oil. Follow the Steps before starting the engine. 14. Start the engine and allow to run for 10 minutes, stop the engine. Check for leaks. 15. CAUTIONS: Make sure that the selector lever and the gearshift mechanism are in the park (P) position. Make sure that the hood is open. Turn the ignition on.
27 16. Press the right-hand directional button to access the instrument cluster menu. 17. Press the right-hand OK button.
28 18. Press the right-hand directional button to access the Oil Level Display.
29 19. Press the right-hand OK button and follow the instructions. 20. Press the cruise control cancel button twice within 2 seconds.
30 21. The message center display will revert to the normal display in the trip computer. Press the right-hand OK button and follow the instructions. Check that the oil level display shows an oil level reading. Only after having started and run the engine for 10 minutes (as indicated in Step 14), switch off the engine, then stabilizing for 10 minutes, take a reading from the oil level display and, if necessary top up with engine oil. 22. NOTE: If instructed to follow Steps in a previous step, return to Step 14 and continue the procedure. Turn the ignition off. 23. Allow 10 minutes for the engine oil level to stabilize if there has been additional oil top up.
31 24. NOTE: The following steps are to update the average oil level value. Turn the ignition on. Press and hold the cruise control cancel button for more than 2 seconds. 25. The message center display will revert to the normal display in the trip computer. 26. Turn the ignition off. 27. Turn the ignition on.
32 28. Press the right-hand directional button to access the instrument cluster menu. 29. Press the right-hand OK button.
33 30. Press the right-hand directional button to access the Oil Level Display.
34 31. Press the right-hand OK button and follow the instructions. Make sure that the average oil level value has now been updated. 32. Refer to: Engine Undershield ( Front End Body Panels, Removal and Installation). 33. Torque: 10 Nm
35 PUBLISHED: 04-DEC RANGE ROVER SPORT (LS), ENGINE - V8 N/A 5.0L PETROL SPECIFICATIONS Engine Data ENGINE DESCRIPTION ENGINE CAPACITY MAXIMUM ENGINE TORQUE (EEC) MAXIMUM ENGINE POWER (EEC) COMPRESSION RATIO BORE STROKE 90 "Vee" 8 Cylinder 32 Valves ccm 510 Nm at RPM 276 kw at RPM 11.5 ± mm 93 mm Engine Firing Order FIRING ORDER 1:2:7:3:4:5:6:8 Engine Valve Clearance (cold) INTAKE VALVE EXHAUST VALVE N/A 0.25 mm ± 0.02 Spark Plugs SPECIFICATION SPARK PLUG GAP ILKR6C-10 1 mm Lubricants, Fluids, Sealers and Adhesives DESCRIPTION SPECIFICATION Engine Oil - Vehicles built up to 2015 SAE 5W20 WSS-M2C925-A or SAE 0W20 STJLR Engine Oil - Vehicles built from 2015 SAE 0W20 STJLR Sealant WSE-M4G323-A6
36 Core plug and stub pipe retainer WSK-M2G349-A7 Capacities DESCRIPTION LITERS Engine oil, initial fill 9.5 Engine oil, service fill with oil filter change 8.0 Cylinder Head and Valve Train ITEM Cylinder head maximum permitted warp (flatness specification) SPECIFICATION 0.2mm (0.008in) Valve guide inner diameter (mm) 5.51 ± 0.01 Intake valve effective length (mm) (tip to gauge line) ± 0.1 Exhaust valve effective length (mm) (tip to gauge line) ± 0.1 Valve stem to guide clearance intake diametrical (mm) Valve stem to guide clearance exhaust diametrical (mm) Valve head diameter intake (mm) 36 ± 0.1 Valve head diameter exhaust (mm) 30 ± 0.1 Intake valve face angle (degrees) ± Exhaust valve face angle (degrees) ± Valve stem diameter intake (mm) ± Valve stem diameter exhaust (mm) ± Valve spring free length (mm) - inlet Valve spring free length (mm) - exhaust 46.1 Valve spring installed height (mm) - inlet Valve spring installed height (mm) - exhaust 35.1 Camshaft lobe lift intake (mm) 5.5 (low) (high) Camshaft lobe lift exhaust (mm) 9.36 Camshaft journal to cylinder head bearing surface clearance diametrical (mm) Camshaft journal diameter - all positions ± 0.01 Bearing diameter - all positions ± 0.01 Camshaft journal maximum run out limit (mm)
37 Camshaft journals to end journals 0.03 Camshaft journals to adjacent journals Camshaft journal maximum out of round (mm) - all journals Torque Specifications NOTE: A = Refer to procedure for correct torque sequence. DESCRIPTION NM LB-FT LB-IN Engine cover mounting bolts Accessory drive belt tensioner retaining bolt Secondary drive belt idler retaining bolts Power steering pump pulley retaining bolts Power steering pump retaining bolts Power steering pump bracket to engine retaining bolts Generator retaining bolts Starter motor retaining bolts Air conditioning compressor retaining bolts Engine mounting to engine mounting bracket retaining nuts Engine mounting to subframe retaining bolts Engine mounting bracket to engine retaining bolts Crankshaft damper pulley retaining LH threaded bolt Flexplate retaining bolts Exhaust manifold heat shield retaining bolts A - - Exhaust manifold retaining bolts A - - Engine wiring harness bracket retaining bolts Coolant outlet pipe Intercooler retaining bolts Intake manifold retaining bolts Oil Cooler retaining bolts
38 Knock sensor (KS) retaining bolt Ignition coil retaining bolts 8-71 Spark plugs Fuel rail retaining bolts A - - High pressure fuel pipe retaining bolts A - - High pressure fuel pump retaining bolts Oil filter housing assembly retaining bolts Oil filter cap Lifting eye bolts Manifold absolute pressure and temperature (MAPT) sensor sensor retaining bolts 5-44 Coolant pump retaining bolts Variable valve timing (VVT) oil control solenoid retaining bolts Camshaft position (CMP) sensor retaining bolts Camshaft cover retaining bolts Front upper timing cover retaining bolts Front lower timing cover retaining bolts A - - Engine rear cover retaining bolts A - - VVT to camshaft retaining bolts Camshaft bearing caps retaining bolts Primary timing chain fixed guide retaining bolts Primary timing chain tensioner retaining bolts Primary timing chain tensioner guide blade retaining bolts Auxiliary chain tensioner guide retaining bolts Auxiliary chain fixed guide retaining bolt Oil pump sprocket retaining bolt Cylinder head retaining bolts A - - Engine oil level (EOL) sensor retaining bolt Crankshaft position (CKP) sensor retaining bolt Oil sump body to engine retaining bolts Oil pan drain plug Oil transfer tube to Oil pan body retaining bolts
39 Oil pump to engine block retaining bolts Pick-up pipe to oil pump retaining bolts Windage tray retaining bolts Piston cooling jet retaining bolts Engine block coolant draining plug Cooling fan pulley Connecting Rod bolts Stage Stage Main bearing cap M10 bolt Stage M10 bolt Stage M8 bolt Stage M8 bolt Stage PUBLISHED: 11-MAY RANGE ROVER SPORT (LS), FRONT END BODY PANELS ENGINE UNDERSHIELD (G354673) REMOVAL AND INSTALLATION ENGINE UNDERSHIELD ALL DERIVATIVES 0.20 USED WITHINS REMOVAL
40 1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle. 2. CAUTION: Note the special washer. Remove the engine undershield. Remove the 10 bolts. INSTALLATION 1. To install, reverse the removal procedure. Tighten the bolts to 62 Nm (46 lb.ft). PUBLISHED: 13-JUL RANGE ROVER SPORT (LS),
41 BATTERY, MOUNTING AND CABLES SPECIFICATIONS Torque Specifications DESCRIPTION NM LB-FT Battery clamp bolts 5 4 Battery terminal nuts 5 4 Battery tray nuts 12 9 Auxiliary battery tray nuts 12 9 PUBLISHED: 12-JUN RANGE ROVER SPORT (LS), ENGINE - V8 S/C 5.0L PETROL SPECIFICATIONS Engine Data ENGINE DESCRIPTION ENGINE CAPACITY MAXIMUM ENGINE TORQUE (EEC) MAXIMUM ENGINE POWER (EEC) COMPRESSION RATIO BORE STROKE 90 "Vee" 8 Cylinder 32 Valves ccm 625 Nm at RPM 375 kw at RPM 9.5 ± mm 93 mm Engine Firing Order FIRING ORDER 1:2:7:3:4:5:6:8
42 Engine Valve Clearance (cold) INTAKE VALVE EXHAUST VALVE 0.20 ± ±0.02 Spark Plugs SPECIFICATION SPARK PLUG GAP ILKR6C-10 1 mm Lubricants, Fluids, Sealers and Adhesives DESCRIPTION SPECIFICATION Engine Oil WSS-M2C925-A Sealant WSE-M4G323-A6 Core plug and stub pipe retainer WSK-M2G349-A7 Capacities DESCRIPTION LITERS Engine oil, initial fill 9.65 Engine oil, service fill with oil filter change 8.0 Cylinder Head and Valve Train ITEM SPECIFICATION Cylinder head maximum permitted warp (flatness specification) 0.2 Valve guide inner diameter (mm) 5.51 ± 0.01 Intake valve effective length (mm) (tip to gauge line) ± 0.1 Exhaust valve effective length (mm) (tip to gauge line) ± 0.1 Valve stem to guide clearance intake diametrical (mm) Valve stem to guide clearance exhaust diametrical (mm) Valve head diameter intake (mm) 36 ± 0.1 Valve head diameter exhaust (mm) 30 ± 0.1 Intake valve face angle (degrees) ± Exhaust valve face angle (degrees) ± 0.125
43 Valve stem diameter intake (mm) ± Valve stem diameter exhaust (mm) ± Valve spring free length (mm) - inlet 46.1 Valve spring free length (mm) - exhaust 46.1 Valve spring installed height (mm) - inlet Valve spring installed height (mm) - exhaust 35.1 Camshaft lobe lift intake (mm) 10 Camshaft lobe lift exhaust (mm) 9.36 Camshaft journal to cylinder head bearing surface clearance diametrical (mm) Camshaft journal diameter - all positions ± 0.01 Bearing diameter - all positions ± 0.01 Camshaft journal maximum run out limit (mm) Camshaft journals to end journals 0.03 Camshaft journals to adjacent journals Camshaft journal maximum out of round (mm) - all journals Torque Specifications NOTE: A = Refer to procedure for correct torque sequence. DESCRIPTION NM LB-FT LB-IN Engine cover mounting bolts Accessory drive belt tensioner retaining bolt Supercharger belt idler/tensioner bracket retaining bolts Secondary drive belt idler retaining bolts Power steering pump pulley retaining bolts Power steering pump retaining bolts Power steering pump bracket to engine retaining bolts Generator retaining bolts Starter motor retaining bolts Air conditioning compressor retaining bolts
44 Engine mounting to engine mounting bracket retaining nuts Engine mounting to subframe retaining bolts Engine mounting bracket to engine retaining bolts Crankshaft damper pulley retaining LH threaded bolt Flexplate retaining bolts Exhaust manifold heat shield retaining bolts A - - Exhaust manifold retaining bolts A - - Engine wiring harness bracket retaining bolts Coolant outlet pipe Intercooler retaining bolts Oil Cooler retaining bolts Knock sensor (KS) retaining bolt Ignition coil retaining bolts 8-71 Spark plugs Fuel rail retaining bolts A - - High pressure fuel pipe retaining bolts A - - High pressure fuel pump retaining bolts Oil filter housing assembly retaining bolts Oil filter cap Lifting eye bolts Manifold absolute pressure and temperature (MAPT) sensor sensor retaining bolts 5-44 Coolant pump retaining bolts Variable valve timing (VVT) oil control solenoid retaining bolts Camshaft position (CMP) sensor retaining bolts Camshaft cover retaining bolts Front upper timing cover retaining bolts Front lower timing cover retaining bolts A - - Engine rear cover retaining bolts A - - VVT to camshaft retaining bolts Camshaft bearing caps retaining bolts
45 Primary timing chain fixed guide retaining bolts Primary timing chain tensioner retaining bolts Primary timing chain tensioner guide blade retaining bolts Auxiliary chain tensioner guide retaining bolts Auxiliary chain fixed guide retaining bolt Oil pump sprocket retaining bolt Cylinder head retaining bolts A - - Engine oil level (EOL) sensor retaining bolt Crankshaft position (CKP) sensor retaining bolt Oil sump body to engine retaining bolts Oil pan drain plug Oil transfer tube to Oil pan body retaining bolts Oil pump to engine block retaining bolts Pick-up pipe to oil pump retaining bolts Windage tray retaining bolts Piston cooling jet retaining bolts Engine block coolant draining plug Cooling fan pulley Connecting Rod bolts Stage Stage Main bearing cap M10 bolt Stage M10 bolt Stage M8 bolt Stage M8 bolt Stage
FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G )
PUBLISHED: 10-OCT-2017 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G1473741) GENERAL PROCEDURES 19.90.17 HIGH PRESSURE FUEL TIMING CHECK AND
More informationSECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep
More informationSECTION A Engine 3.7L
303-01A-i Engine 3.7L 303-01A-i SECTION 303-01A Engine 3.7L CONTENTS PAGE SPECIFICATIONS... 303-01A-2 303-01A-2 Engine 3.7L 303-01A-2 SPECIFICATIONS Material Motorcraft High Performance Engine RTV Silicone
More informationWSS- M97B51-A1 WSS- M2C930-A. 5.7L (6 qt) with filter WSE- M4G323-A4
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual SPECIFICATIONS Procedure revision date: 01/22/2009 Material Item Specification Fill Capacity Gasket Maker TA-16 WSK- M2G348-A5 Motorcraft
More information2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
More informationSECTION B Engine 5.0L (4V)
303-01B-i Engine 5.0L (4V) 303-01B-i SECTION 303-01B Engine 5.0L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01B-2 303-01B-2 Engine 5.0L (4V) 303-01B-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep
More informationPage 1 of 32 09-Mar-2014 Fuel Charging and Controls - V8 5.0L Petrol - High Pressure Fuel Pump 1 Removal and Installation Removal CAUTION: Always carry out the cleaning process before carrying out any
More informationASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)
303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket
More informationEngine 3.5L 2010 Edge, MKX. SPECIFICATIONS Procedure revision date: 08/26/2013. Specification. Item Specification Fill Capacity
2010 Edge Report a prolem with this article 303-01 Engine 3.5L 2010 Edge, MKX SPECIFICATIONS Procedure revision date: 08/26/2013 s Material Fill Capacity Motorcraft High Performance Engine RTV Silicone
More informationAJV8 Engine Assembly. AJV8 Engine Assembly
AJV8 Engine Assembly Contents Cylinder Block Dowels, Plugs and Pipes 2 4 Crankshaft Bearing and Cylinder Bore Dimensions 5 9 Bearing Measuring 6 Engine Dimensions and Codes 6 7 Main Bearing Selection Chart
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More informationEngine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D)
SECTION 303-01A: Engine 4.0L SOHC 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 05/10/2010 Engine Special Tool(s) Adapter for 303-564 303-578 (T97T-6256-A) Adapter for 303-577 303-576
More informationGeneral Specifications
General Specifications General Engine management EEC V Emission standard 96 EC Engine code Y5A Firing order 1 3 4 2 Bore mm 89,6 Stroke mm 91 Cubic capacity cc 2295 Compression ratio 10,0:1 Compression
More informationPage 1 of 75 303-01D Engine - 5.2L 32V Ti-VCT 2016 Mustang Assembly Procedure revision date: 12/15/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 205-142 (T80T-4000-J) Installer,
More informationGeneral Specifications
General Specifications Engine Data General Engine management EEC V/SEFI Emission standard 96 EEC Engine code N3A Firing order 1-3-4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cc 1998 Compression ratio
More informationIntake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
More informationTECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump SERVICE DATE MODEL 2002 MY.
SERVICE V8 XJ Series DATE 12/02 TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump 100-21 MODEL 2002 MY V8 XJ Series VIN F44114 - F55936 Issue: Some 2002
More informationEngine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
More informationASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More information2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper
More informationDISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
More informationDISASSEMBLY. Engine. Special Tool(s) Locking Tool, Camshaft Phaser Sprocket Special Tool(s)
303-01B-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Rear Slinger 303-514 (T95P-6701-AH) Special Tool(s) 303-01B-1 Locking Tool, Camshaft Phaser Sprocket 303-1046 Remover, Crankshaft Rear Seal
More informationGeneral Specifications
General Specifications Engine Data Description Litres Engine management EEC V/SFI Emission standard 96 EEC Engine code NSD Firing order 1-3 - 4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cm 3 1998 Compression
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More informationCylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
More informationEngine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More informationFastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
More informationEngine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)
Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,
More informationDESCRIPTION AND OPERATION
303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589
More informationfile://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...
Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor
More information1995 Aerostar/Ranger/Explorer
Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,
More informationSECTION C Engine 6.4L Diesel
303-01C-i Engine 6.4L Diesel 303-01C-i SECTION 303-01C Engine 6.4L Diesel CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 6.4L Diesel 303-01C-2 SPECIFICATIONS Material Gasket Maker TA-16 Motorcraft
More information2006 Freestar/Monterey Workshop Manual. IN-VEHICLE REPAIR Procedure revision date: 12/01/2005
SECTION 303-01: Engine 3.9L and 4.2L IN-VEHICLE REPAIR Procedure revision date: 12/01/2005 Valve Cover LH Item Part Number Description 1 W708650 Oil level indicator tube bolt 2 6754 Oil level indicator
More information2006 Expedition/Navigator Workshop Manual
7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section
More informationSECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
More informationPage 1 of 11 Assembly 50. Install the timing chain guide. Tighten to 12 Nm. Page 2 of 11 51. Install the crankshaft sprocket. 52. Install the chain tensioning tool 303-532 to the exhaust camshaft sprocket.
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Procedures» Removal Cylinder Heads http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=376&nonstandardid=682956&vehicleid=45317&windowname=maina
More informationPage 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft
More information1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder
ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION
More informationTiming Drive Components ( )
Page 1 of 14 (12.65.13) Removal 1. Remove the engine front cover. For additional information, refer to For additional information, refer to. 2. Remove the spark plugs. 3. Remove the crankshaft position
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
More information2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
More information2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
More informationRemoval. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys
Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission
More informationREMOVAL. Cylinder Head. All cylinder heads. 1. Remove the engine. For additional information, refer to Engine in this section.
303-01B-1 303-01B-1 REMOVAL Cylinder Head Material Item Specification Special Tool(s) Motorcraft Metal Surface Prep Modular Engine Lift Bracket ZC-31 303-F047 (014-00073) or equivalent Silicone Gasket
More informationDISASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More informationM-6007-A50NA Engine Specifications and Owner's Manual
M-6007-A50NA Engine Specifications and Owner's Manual Fordracingparts.com Techline 1-800-367-3788 Page 1 of 11 IS-1850-0377 Please visit www.fordracingparts.com for the most current instruction information.!!!
More information1.6L 4-CYL - VIN [E]
1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES
More informationCylinder Head. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Compressor, Valve Spring
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 03/15/2009 Cylinder Head Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039
More informationK EN R A ugu st Specifications Industrial Engine. M G D (Engine) MGB (Engine)
K EN R 623 0-00 A ugu st 200 6 Specifications 2506-15 Industrial Engine M G A (Engine) MGB (Engine) M G D (Engine) Important Safety Information i01658146 Most accidents that involve product operation,
More informationPage 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and
More information2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)
1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15
More informationPage 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding
More information2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
More informationEngine Dismantle and Assemble ( )
Engine Dismantle and Assemble ( 34 8) Special Tools 5 053 Slide hammer 47 Vibration damper remover 47 5053 00 Splined head socket, cylinder head bolts 87 Mounting stand with geared drive 00 059C Installer
More informationTiming Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar
Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer
More informationIN-VEHICLE SERVICE. Engine Components
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown
More informationPARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
More informationPARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque
ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)
More informationIN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
More informationTiming Chain - Renew ( )
«Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140
More informationENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean.
REPAIRS Seal - crankshaft - rear 1. Ensure both seal location and running surface on crankshaft are clean. 1. Automatic gearbox models: converter drive plate. ENGINE - V8, REPAIRS, Plate - drive - automatic.
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01A-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01A-1 Special Tool(s) SAE 5W-20 Premium WSS-M2C930-A Synthetic Blend Motor Oil Alignment Plate, Camshaft XO-5W20-QSP (in Canada
More informationEngine Dismantle and Assemble ( )
Engine Dismantle and Assemble (21 134 8) Special Tools 15-030A Universal flange-holding wrench 21147 21-147 Vibration damper remover 15030A 16-067 Locator for clutch disc 21-167 Wrench for cylinder head
More information2007 Ford Freestyle SEL
Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold
More informationIN-VEHICLE REPAIR. Camshaft RH. Removal. 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section.
303-01B-1 IN-VEHICLE REPAIR Camshaft RH Special Tool(s) Compressor, Valve Spring 303-1039 Wedge, Timing Chain 303-1175 303-01B-1 2. Remove the RH valve cover. For additional information, refer to Valve
More informationDISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX)
2012 Cadillac CTS Wagon AWD V6-3.0L Vehicle > Engine, Cooling and Exhaust > Engine > Locations > Components DISASSEMBLED VIEWS Disassembled Views Engine Covers and Component Assemblies (1 of 2) (LF1, LFW
More informationEngine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
More information2010 Transit Connect Workshop Manual. 31. Remove the 3 bolts, thermostat housing and thermostat.
31. Remove the 3 bolts, thermostat housing and thermostat. 32. Remove the 2 bolts, stud bolt and the A/C compressor. 33. Remove the bolt and the KS. 34. Remove the 8 bolts and the crankcase vent oil separator.
More informationTorque Guidelines (Z 22 SE)
Page 1 of 14 Torque Guidelines (Z 22 SE) No. Designation Nm 1 Retaining bolts, coolant pump sprocket to coolant pump 2 Retaining bolts, balancer shaft timing chain guide rail to 3 Retaining bolts, balancer
More informationPARTIAL ENGINE ASSY (2ZZ GE)
COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy
More information2002 Mustang Workshop Manual
Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)
More informationPage 1 of 8 303-01A Engine 2.3L 2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid IN-VEHICLE REPAIR Procedure revision date: 10/05/2008 Cylinder Head Special Tool(s) Alignment Plate, Camshaft 303-465 (T94P-6256-CH)
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More information2004 F-150 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047
More information1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder
NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness
More informationhttps://www.hyundaitechinfo.com/viewer/content.asp?isprint=true&imgnum=1&print_titl...
Page 1 of 7 VELOSTER(FS) >2013 > G 1.6 T-GDI > Engine Mechanical System > General Information > Specifications Specifications General Type Description Specifications Except Europe In-line, DOHC Number
More informationservice bulletin MCM 7.4L Bravo, MIE 7.4L Inboard GM Generation V Engine Specifications No. 91-6
service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 91-6 MCM 7.4L Bravo, MIE 7.4L Inboard GM Generation V Engine Specifications NOTE: Generation V Engines Have the Fuel Pump Mounted on the
More informationINTAKE MANIFOLD (G )
PUBLISHED: 13-FEB-2018 2011.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 N/A 5.0L PETROL INTAKE MANIFOLD (G1245958) REMOVAL AND INSTALLATION 30.15.02 MANIFOLD - INTAKE - LH /FRONT /EACH - RENEW 5000 CC,
More information(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel TYPE TIGHTENING TORQUES. Rev. 2.0 OE
(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel 1 TYPE TIGHTENING TORQUES 1. Cylinder head CAUTION : (*) Follow the tightening sequence. Reference Designation (1) bolts - Throttle butterfly housing Tightening
More informationPage 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description
More information7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
More informationFord 4.6L (2V) SPECIFICATIONS
Ford 4.6L (2V) SPECIFICATIONS General Specifications Item Specifications Silicone Gasket and Sealant F7AZ-19554-EA WSE-M4G323-A4 Premium Engine Coolant VC-4A, VC-5 in Oregon, CXC-10 in Canada ESE-M97B44-A
More information2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing
1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement
More information1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
More informationIN-VEHICLE REPAIR. Camshaft RH. Removal. 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section.
303-01C-1 IN-VEHICLE REPAIR Camshaft RH Special Tool(s) 303-01C-1 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section. Compressor, Valve Spring 3. NOTICE:
More informationTORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More informationEngine Remove and Install ( ) Remove. 2,5l TCI Diesel Engine. Special Tools. Workshop Equipment Transmission jack Trolley jack Workshop crane
Engine Remove and Install ( 34 0) Special Tools 068 A 068A Engine lifting tackle 4 003 Coolant hose clamp removal and fitting tool Workshop Equipment Transmission jack Trolley jack Workshop crane Materials
More informationPistons and Connecting Rods, Remove and Install
Page 1 of 46 Pistons and Connecting Rods, Remove and Install Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release
More information5.7L ENGINE PARTS BOOK. Not for. Reproduction
5.7L ENGINE PARTS BOOK Engine Model: Engine Family: PSI, Industrial Engine Spec N.: 39004120-39004248 Parts Book Revision: December, 2015 TABLE OF CONTENTS SECTION PAGE CYLINDER BLOCK... 3-5 CYLINDER HEAD...
More informationBMW DIESEL. Pistons DESCRIPTION
BMW DIESEL DESCRIPTION The diesel engine fitted to New Range Rover is a 2.5 litre, liquid cooled, 6 cylinder, in-line unit. It has an electronically regulated fuel injection system and is turbocharged.
More informationIN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Position the crankshaft keyway at the 12 o clock position.
303-01B-1 IN-VEHICLE REPAIR Timing Drive Components 303-01B-1 Special Tool(s) Compressor, Valve Spring 303-1039 Locking Tool, Camshaft Phaser Sprocket 303-1046 3. Position the crankshaft keyway at the
More informationWorkshop Manual. F-Super Duty : Powertrain. 03: Engine
Workshop Manual 1999 F-Super Duty 250-550 3: Powertrain 03: Engine 1999 F-Super Duty 250-550 Contents/Index GROUP 03: Engine SECTION 303-00: Engine System General Information SECTION 303-01A: Engine 5.4L
More information2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)
Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with
More informationNOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
More informationCylinder head/gasket, replacing
1(16) Cylinder head/gasket, replacing Special tools: 951 2666, 951 2767, 999 5450, 999 5452, 999 5454, 999 5670, 999 5718, 999 5719, 999 5750, 999 5972 Removing the cylinder head gasket Note! As the illustrations
More information2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
More informationTiming Chain Renew ( )
Timing Chain Renew (1 314 0) Special Tools 1 137 Oil seal installer/aligner, crankshaft front 1168 1 168 Crankshaft immobilising tool 1137 1 140 Engine support bar 4 003 Remover/installer, radiator hose
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More information