1995 Aerostar/Ranger/Explorer

Size: px

Start display at page:

Download "1995 Aerostar/Ranger/Explorer"

Alicia Rodgers
5 years ago
Views:

1 Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses, emission control system, ignition system, flywheel or flexplate and front end accessory drive components. For more detailed information on any particular system, refer to the specific section in the appropriate repair group. NOTE: All valve train components should be identified to make sure they are installed in their original positions during assembly. With the engine (6007) mounted on a work stand: Remove the left and right hand valve covers (6582) as outlined in this section and discard the gaskets. 2. Remove the right exhaust manifold (9430) and left exhaust manifold. 3. Remove the upper intake manifold, the fuel injection supply manifold (9D280), fuel injectors and lower intake manifold as outlined in Section 03-04C and in this section. 4. Remove the bolt and clamp retaining the oil pump drive shaft and remove the oil pump drive shaft. 5. Remove the oil level dipstick (6750) and oil level indicator tube (6754) and remove the oil filter, adapter and oil cooler (if equipped). 6. Remove the rocker arm (6564), rocker arm shaft (6563), rocker arm shaft support (6531), and push rod (6565) as outlined in this section. 7. Remove the cylinder heads (6049) as outlined in this section. 8. Remove the crankshaft position sensor (CKP sensor) (6C315), crankshaft vibration damper and pulley (6B321) from the front of the engine as outlined in this section. 9. Remove the oil pan (6675) as outlined in this section and discard the oil pan gasket (6710). 10. Remove the water pump housing gasket (8507) and front cover as an assembly. Discard the gasket and seal. 11. Remove the oil pump (6600), oil pump screen cover and tube (6622), oil pump intermediate shaft (6A618) and crankshaft oil windage baffle (6L680). 12. Remove the crankshaft rear oil seal. 13. Remove the timing chain vibration damper (6284). 14. Remove the camshaft sprocket capscrew and slide the timing chain vibration damper, crankshaft sprocket (6306) and camshaft sprocket (6256) off as an assembly. Remove the timing chain guide (6K297). 15. Remove the camshaft thrust plate (6269) and remove the camshaft (6250). 16. NOTE: Pistons (6108), connecting rods (6200) and connecting rod bearings (6211) should be numbered to make sure they are assembled in their original positions. NOTE: Before removing pistons, inspect the top of the cylinder bores. If necessary, remove the ridge and/or carbon deposits from each cylinder using Cylinder Ridge Reamer T64L-6011-EA. Remove the connecting rod caps and remove the pistons. 17. CAUTION: When removing the crankshaft (6303), take care not to damage any of the bearing surfaces on the crankshaft. NOTE: The location of the main bearing caps and the crankshaft main bearings (6333) should be identified. When the engine is assembled, crankshaft main bearings which are to be reused should be installed in their original positions. Remove the crankshaft main bearing caps, crankshaft main bearings and crankshaft. 18. For cleaning purposes, the oil gallery and coolant drain plugs can be removed. Assembly SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Rear Crank Seal Replacer T97T-6701-A Rear Oil Seal Replacer T95T-6701-A Valve Stem Seal Replacer T90T-6571-A Before assembling cylinder block (6010), all sealing surfaces must be clean and free of chips, dirt, paint, and foreign material. Also, make sure coolant and oil passages are clear. If new piston rings are to be installed and no visible cross hatch marks remain on the cylinder wall, remove cylinder wall glaze using a spring type tool. Follow instructions of tool manufacturer. Crankshaft Assembly, Installation

2 Page 2 of 13 Item Part Number Stud, Main Bearing Cap (4 Places) Bolt, Main Bearing Cap (4 Places) 3 Main Bearing Cap (Part of 6010) Crankshaft Thrust Main Bearing (No. 3 Main Bearing) Crankshaft Main Bearing (No. 2) Crankshaft Sprocket G5 Key Crankshaft Main Bearing (No. 1) Oil Gallery Plug Crankshaft Main Bearing (No. 4) Crankshaft 12 Rear Main Bearing Cap (Part of 6010) Oil Gallery Plug Camshaft Rear Bearing Cover A Tighten to Nm (66-77 Lb-Ft) B Tighten to 6-12 Nm (4-9 Lb-Ft) Description C Seal Here with Silicone Rubber D6AZ BA or Equivalent Meeting Ford Specifications ESB-M4G92-A and ESE-M4G195-A D Apply Engine Fill Oil E Tighten to Nm (20-27 Lb-Ft) 1. NOTE: Lightly oil all attaching bolt and stud threads before installation, except those specifying special sealant. CAUTION: Prevent engine contamination. Always use necessary precautions to prevent old sealer or gasket material from falling into the engine. Before beginning to assemble engine : a. Clean ALL the oil and the old sealer from the oil pan, taking special care to remove ALL the old sealer from the oil pan gasket groove in the oil pan. Thoroughly wash the oil pan. b. Clean ALL the old sealer from the rear main bearing cap USING A SCRAPER AND WIRE WHEEL. The original sealer used during production assembly becomes extremely hard after it has cured. It is extremely important that ALL the old sealer be removed from joint faces and grooves. c. Clean ALL the oil and old sealer from the cylinder block oil pan sealing area and the rear main bearing cap joint area. d. After all the parts have been cleaned they must be wiped down with a cleaner that leaves no residue or film such as Ford Extra Strength Spot Remover B7A AA meeting Ford specification ESR-M5B197-A or denatured alcohol. e. Clean the transmission bell-housing area and the rear of the cylinder block of ALL oil residue. Verify with a black light that all oil residues have been cleaned from this area. 2. Place crankshaft upper main bearings in position in the bores with the tang fitting in the slot provided. Lubricate bearings with SAE 50 Service SG oil. 3. Install the lower main bearings in the bearing caps. 4. Lower crankshaft into place. Use care to prevent damage to bearing surfaces. 5. Check clearance of each main bearing, following the procedure under Fitting Main and Connecting Rod Bearings in Section After crankshaft main bearings have been fitted, apply SAE 50 Service SG oil to the journals and bearings. 7. NOTE: Apply Silicone Rubber D6AZ BA meeting Ford specifications ESB-M4G92 and ESE-M4G195-A or equivalent in a 1.59mm (1/16-inch) bead in each corner of rear main bearing cap saddle, the full length of the saddle. Install all bearings and caps except thrust bearing cap (No. 3 bearing). MAKE SURE MAIN BEARING CAPS ARE INSTALLED IN THEIR ORIGINAL POSITION. Tighten bearing caps to Nm (66-77 lb-ft).

Page 3 of 13 8. Install thrust bearing cap (No. 3) with bolts finger-tight. 9. Pry crankshaft forward against thrust surface of upper half of bearing. 10.

3 cap bolts to specification. 12. Force crankshaft toward the rear of the engine. 13. Check crankshaft end play. End play should be 0.05-0.32mm (0.002-0.0125 inch). Refer to Section 03-00.

3 Page 3 of Install thrust bearing cap (No. 3) with bolts finger-tight. 9. Pry crankshaft forward against thrust surface of upper half of bearing. 10. Hold crankshaft forward and pry thrust bearing cap to the rear. This will align thrust surfaces of both halves of the bearing. 11. Retain forward pressure on crankshaft. Tighten No. 3 cap bolts to specification. 12. Force crankshaft toward the rear of the engine. 13. Check crankshaft end play. End play should be mm ( inch). Refer to Section Thrust Bearing Cap, Installation 14. Coat all camshaft bearings, camshaft lobes and oil pump drive shaft with SAE 50 Service SG oil. 15. Slide camshaft carefully through camshaft bearings. Install camshaft thrust plate with groove toward cylinder block. Tighten thrust plate retaining bolts. 16. Check camshaft end play. Refer to Section If not within specification, replace camshaft thrust plate. 17. Install the timing chain guide with the guide pin in to the oil supply hole. Tighten guide bolts to Nm (7-9 lb-ft). 18. Install camshaft sprocket, timing chain/belt (6268) and crankshaft sprocket. Position sprockets and timing chain/belt on camshaft and crankshaft simultaneously. 19. NOTE: A packaging clip from a new automatic tensioner can be used to hold tensioner in a retracted position. If a packaging clip is not available, fabricate a clip using shop materials. 20. With the timing chain vibration damper held in the retracted position with clip, install the tensioner and tighten the bolts to 9-11 Nm (7-8 lb-ft). 21. Install the camshaft capscrew. Tighten camshaft capscrew to Nm (44-50 lb-ft). 1 E S200 Torx Screw Camshaft Sprocket Camshaft 4 E S75 Torx Bolt 5 6K297 Timing Chain Guide

Page 4 of 13 6 6268 Timing Chain/Belt 7 6K254 Timing Chain/Belt Tensioner 8 E600112-5 Bolt 9 6269 Camshaft Thrust Plate A Tighten to 60-68 Nm (44-50 Lb-Ft) B Camshaft End Play to Be Within 0.065-0.

4 Page 4 of Timing Chain/Belt 7 6K254 Timing Chain/Belt Tensioner 8 E Bolt Camshaft Thrust Plate A Tighten to Nm (44-50 Lb-Ft) B Camshaft End Play to Be Within mm ( Inch) C Tighten to Nm (7-9 Lb-Ft) D Tighten to 9-11 Nm (7-8 Lb-Ft) 22. After the sprockets have been installed, insert the crankshaft sprocket key. Make sure timing marks on the sprockets are aligned as shown Camshaft Sprocket 2 Camshaft Timing Mark (Part of 6256) 3 6K297 Timing Chain Guide 4 Crankshaft Timing Mark (Part of 6306) Crankshaft Sprocket 6 6K254 Timing Chain/Belt Tensioner 23. Remove the clip that holds the timing chain vibration damper in a released position. 24. Oil the piston rings, pistons and cylinder walls. Be sure to install the pistons in the same cylinders from which they were removed. 25. Make sure the ring gaps are properly spaced around the circumference of the piston. Refer to Piston and Connecting Rod Installation in this section. 26. NOTE: Install piston with indentation notch in the piston head toward front of engine. Install a piston ring compressor on the piston and push piston in with a hammer handle until it is slightly below the top of the cylinder. Be sure to guide connecting rods to avoid damaging crankshaft journals (cover studs). 27. Check clearance of each connecting rod bearing. Refer to procedure in Section After bearings have been fitted, apply a light coat of SAE 50 Service SG oil to the journals and bearings. 29. Turn the crankshaft throw to the bottom of its stroke. Push piston all the way down until connecting rod bearing seats on the crankshaft journal. 30. Install connecting rod cap. Tighten nuts to Nm (18-24 lb-ft). 31. Check side clearance between connecting rods on each crankshaft journal.

Page 5 of 13 32. Check the crankshaft and connecting rod bearings for assembled rotational torque.

Check the piston installed height if any of the following repair procedures have been performed: New pistons were installed. New connecting rods were installed. New cylinder block was installed.

Refer to Piston and Connecting Rod Removal and Installation procedures in this section for piston height checking procedure. 34. NOTE: New rear main bearing bolts must be used during assembly.

5 Page 5 of Check the crankshaft and connecting rod bearings for assembled rotational torque. Torque required to rotate the crankshaft assembly with pistons installed is not to exceed 45 Nm (33 lb-ft). 33. Check the piston installed height if any of the following repair procedures have been performed: New pistons were installed. New connecting rods were installed. New cylinder block was installed. Cylinder block machine work (that could affect cylinder block deck height). Cylinder block crankshaft align boring. Refer to Piston and Connecting Rod Removal and Installation procedures in this section for piston height checking procedure. 34. NOTE: New rear main bearing bolts must be used during assembly. Seal and assemble the rear main cap to the cylinder block. a. Place a bead of Ford Gasket Eliminator E1FZ A meeting Ford specification WSK-M2G348-AA or Loctite 515 sealer to the block along the corners of the rear main bearing cap joint area and on the joint face, approximately 13mm (1/2 inch) from the rear of the block as shown in illustration. b. Verify that the lower rear main bearing insert is in place. Install the rear main bearing cap and snug the bolts. c. Align the rear main bearing cap to cylinder block by moving the bearing fore or aft approximately 13mm (1/2 inch) inward in the rear oil seal bore so that the rear seal stop of the block and cap line up. This will ensure that the crankshaft rear oil seal (6701) will seat squarely when installed in the bore. d. Torque the rear main cap bolts to Nm (66-77 lb-ft). e. Fill the cavities on both sides of the rear main cap with Ford Gasket Eliminator E1FZ A meeting Ford specification WSK-M2G348-A4 or Loctite 515. f. Wipe the excessive sealer from the cylinder block/rear main cap area. 35. Install the crankshaft oil windage baffle. Tighten nuts to Nm (13-15 lb-ft). 36. Prime the oil pump with XO-5W30-QSP meeting Ford specification ESE-M2C153-E or equivalent SAE 5W-30 Service SG oil and install oil pump, oil pump intermediate shaft, and oil pump screen cover and tube. Tighten oil pump bolts to Nm (13-15 lb-ft).

Page 6 of 13 1 6A618 Oil Pump Intermediate Shaft 2 6629 Oil Pump Intermediate Shaft Retaining Ring 3 6622 Oil Pump Screen Cover and Tube 4 6600 Oil Pump 5 E804387 Screw 6 E804553 Screw 7 6626 Oil

6 Page 6 of A618 Oil Pump Intermediate Shaft Oil Pump Intermediate Shaft Retaining Ring Oil Pump Screen Cover and Tube Oil Pump 5 E Screw 6 E Screw Oil Pump Inlet Tube Gasket A Tighten to Nm (13-15 Lb-Ft) B Tighten to 9-13 Nm (7-10 Lb-Ft) 37. Install crankshaft rear oil seal. ( Refer to the procedure in this section.) 38. Install crankshaft front seal (6700), gasket, and front cover. Tighten cover bolts to Nm (13-15 lb-ft). 39. Install crankshaft vibration damper and pulley as detailed in this section. Tighten bolt to Nm (30-37 lb-ft). Then tighten bolt another 85 degrees. 40. Install crankshaft position sensor and tighten bolts to 9-12 Nm ( lb-in). 41. Install the oil filter adapter (6881), oil cooler (if equipped) and a new oil bypass filter (6714). Oil Pan, Installation 1 E S72 Bolt, M6 2 6C624 Low Oil Level Sensor 3 6C626 Low Oil Level Sensor Washer Oil Pan Oil Pan Gasket 6 E60012-S72 Nut 7 Stud (Part of 6010) 8 6A674 Clip Oil Pan Drain Plug Gasket Oil Pan Drain Plug

Page 7 of 13 11 6C629 Torx Bolt A Tighten to 7-10 Nm (5-7 Lb-Ft) B Tighten to 17-21 Nm (13-20 Lb-Ft) C Tighten to 4 Nm (35 Lb-In) 42. Install and seal the oil pan: a.

b. Place a bead of Ford Silicone Sealer F1AZ-19562-A meeting Ford specification WSE-M4G320-A2 or Loctite 598 on top of the oil pan gasket at the radius areas at the front and rear of the oil pan. c.

7 Page 7 of C629 Torx Bolt A Tighten to 7-10 Nm (5-7 Lb-Ft) B Tighten to Nm (13-20 Lb-Ft) C Tighten to 4 Nm (35 Lb-In) 42. Install and seal the oil pan: a. Place a bead of Ford Silicone Sealer F1AZ A meeting Ford specification WSE-M4G320-A2 or Loctite 598 sealer in the oil pan gasket groove at the radius areas at the front and rear of the oil pan. b. Place a bead of Ford Silicone Sealer F1AZ A meeting Ford specification WSE-M4G320-A2 or Loctite 598 on top of the oil pan gasket at the radius areas at the front and rear of the oil pan. c. Place a bead of Ford Silicone Sealer F1AZ A meeting Ford specification WSE-M4G320-A2 or Loctite 598 on the cylinder block at the cylinder block to front cover joint area. d. Set the oil pan in place and snug the 4 pan nuts. Ensure integral wedge seal is properly located. e. Align the rear face of the oil pan with the rear face of the cylinder block. f. Install the remaining oil pan bolts and torque to 7-10 Nm (62-89 lb-ft). 43. NOTE: Always use a new rear main seal. Refer to Crankshaft Rear Oil Seal Installation in this section. 44. NOTE: The transmission bolts to the engine and oil pan when installed, so it is important to measure the difference between the surface of the rear face of the oil pan (at the spacer locations) and the rear face of the cylinder block. If the rear face of the oil pan cannot be aligned within.0100 in. of the rear face of the cylinder block, the appropriate shims must be used. Refer to the following procedure for checking this dimension. CAUTION: Failure to measure the required spacer thickness can result in insufficient, or excessive clearance between the oil pan and transmission when installed in the vehicle. This can lead to oil pan damage, and/or oil leakage. Determine if spacers are needed and if so, what thickness: a. With the oil pan installed on the engine, position a straightedge on the rear of the cylinder block so that it is in contact with the transmission mounting machined face of the cylinder block and extends over one of the oil pan/transmission bolt mounting pads. b. Using a feeler gauge, measure the gap between the mounting pad and the straightedge. Repeat the procedure on the other mounting pad. Select spacers of the required thickness from the chart. c. Install the selected spacers to the mounting pads on the rear of the oil pan before bolting the engine and transmission together. SPACER SELECTION CHART Measured Gap Spacer Required mm Inch mm Inch Shim Color Code None None Yellow Blue

8 Page 8 of Pink 45. Install valve tappets (6500) in their original bores. 46. NOTE: If cylinder head was completely disassembled, refer to Cylinder Head Disassembly and Assembly in this section. NOTE: Head gaskets are not interchangeable. Install cylinder head locating dowels. Position cylinder head gaskets (6051) on cylinder block ensuring the installation arrows on the head gaskets are pointing to the front of the engine. Cylinder Head, Installation Cylinder Head Bolt Cylinder Head Head Gasket (LH) 4 6A008 Cylinder Head to Block Dowel Valve Tappet Head Gasket (RH) A Installation Arrows (on Top) Must Point to Front of Engine 47. Install and tighten the cylinder head bolts, in the sequence shown, in the following steps. Step Nm (22-26 lb-ft) Step Nm (52-56 lb-ft) Step 3 rotate bolts 90 degrees 48. NOTE: Once applied, the silicone sealer will set up in approximately 15 minutes. The intake manifold must be installed immediately after the sealer is applied. Apply Silicone Rubber D6AZ BA or equivalent meeting Ford specifications ESB-M4G92-A and ESE-M4G195-A to the block and cylinder head mating surfaces at the four corners. Install the intake manifold gasket (9439) and again apply sealer to the four corner locations.

Page 9 of 13 1 6049 Cylinder Head 2 9439 Intake Manifold Gasket 3 9424 Intake Manifold A Examine Closely for Erosion, Corrosion, or Pitting on This Surface B Silicone Sealer 4 Places 1 W702301S309M

9 Page 9 of Cylinder Head Intake Manifold Gasket Intake Manifold A Examine Closely for Erosion, Corrosion, or Pitting on This Surface B Silicone Sealer 4 Places 1 W702301S309M Bolt with Captive Washer (8) 2 12A648 Engine Coolant Temperature Sensor Water Temperature Indicator Sender Unit Water Pump 5 Stud (Part of 9424) Intake Manifold Gasket Intake Manifold A Tighten to 16 Nm (12 Lb-Ft) B Used to Locate Lower Intake Manifold Only 49. Position the intake manifold (9424) with the aid of two guide studs in position 3 and 4 below, and then install the intake manifold bolts. Remove the two guide studs and replace with bolts. Tighten the intake manifold bolts in three stages following the sequence shown. a. 8 Nm (6 lb-ft) b. 15 Nm (11 lb-ft) c. 22 Nm (16 lb-ft) 50. NOTE: Lightly oil bolts with engine oil prior to installation. Do not place any oil in the threads on the cylinder head. Install valve tappets, rocker arm and shaft assemblies as outlined in this section.

Page 10 of 13 51. Install oil level indicator tube, oil level dipstick assembly. 52.

Apply Silicone Rubber D6AZ-19562-BA or equivalent meeting Ford specifications ESB-M4G92-A and ESE-M4G195-A to intake manifold-to-cylinder head parting seam and an 8mm (1/8-inch) ball of sealer to

Rocker Arm Cover and Gasket, Installation 1 6582 Valve Cover Aerostar (RH) 2 E800390-S72 Screw, M6x22 Flange Head 3 6582 Valve Cover (LH) 4 W701041 Stud 5 9424 Intake Manifold 6 6049 Cylinder Head

10 Page 10 of Install oil level indicator tube, oil level dipstick assembly. 52. NOTE: Since silicone rubber will set up within 15 minutes, if you are installing both covers, apply only to one side at a time. Apply Silicone Rubber D6AZ BA or equivalent meeting Ford specifications ESB-M4G92-A and ESE-M4G195-A to intake manifold-to-cylinder head parting seam and an 8mm (1/8-inch) ball of sealer to valve cover bolt holes on exhaust side. Rocker Arm Cover and Gasket, Installation Valve Cover Aerostar (RH) 2 E S72 Screw, M6x22 Flange Head Valve Cover (LH) 4 W Stud Intake Manifold Cylinder Head (RH) Valve Cover Gasket Valve Cover Ranger and Explorer (RH) Cylinder Head (LH) Cylinder Block A Tighten to 8-10 Nm (71-89 Lb-In) 53. Install left valve cover, rocker arm cover flange plates (6A523), and bolts and snug bolts starting from center bolts and working in crisscross pattern to end bolts. Tighten in same pattern to 6-8 Nm (53-70 lb-in). 54. Install the upper intake manifold and tighten the nuts to Nm (15-18 lb-ft). 55. Install the oil pump drive and secure with the clamp and bolt. Tighten the bolt to Nm (13-15 lb-ft). For Ranger and Explorer vehicles refer to Assembly, Ranger and Explorer below.

11 Page 11 of Install wiring harnesses, emission control system, fuel system, ignition system and front end accessory drive components, by referring to procedures in the specific sections. Assembly, Ranger and Explorer 1. After performing Steps 1-55 above, rotate crankshaft until TDC mark on the damper is accessible. If not present, place an additional mark on the damper at 26 degrees After Top Dead Center (ATDC). This position is 34mm (1.34 inches) counterclockwise from the Top Dead Center (TDC) mark. 2. Position No. 1 cylinder to TDC between compression and ignition stroke. (Both intake and exhaust valves must be closed with TDC mark on vibration damper at pointer.) 3. Lubricate oil pump drive pinion and O-ring on assembled oil pump drive gear and CID sensor with SM-2C 1013-A oil. Do not get oil above mounting flange. 1 12K073 CID Sensor (California Only) 2 E S O-Ring Oil Pump Drive Assembly Engine Distributor Hold-Down Clamp 6 E Screw A Tighten to Nm (13-15 Lb-Ft) B Maximum Level for Pre-Oiling Drive Gear C Minimum Level for Pre-Oiling Drive Gear 4. NOTE: Normal CID sensor rotation is clockwise viewed from top of CID sensor. Align the CID sensor rotor as shown with the trailing edge of the vane lined up with the short mark at the left hand side of the plastic window. 5. Position the sensor above its hole at right angles to the block rear face. 6. Install the assembled CID sensor and oil pump drive gear into the engine. As the assembly is pushed into place, the camshaft gear will rotate the sensor vane clockwise toward the center of the window.

12 Page 12 of Rotate the CID sensor counterclockwise. Install clamp and screw finger-tight. Rotate the sensor back to its position at right angles to the back of the block. 8. NOTE: For out of vehicle assembly, use loose 12 volt battery or battery in a conveniently located vehicle. Connect the CID Testing Wiring Harness T94T-50-B to the CID Sensor. 9. Connect the CID Testing Wiring Harness leads: a. Red harness wire to battery positive terminal. b. Black harness wire to battery negative terminal. c. Voltmeter positive lead to harnesses white lead. d. Voltmeter negative lead to battery negative terminal. 1 T94T-50-B CID Testing Wiring Harness 2 White Lead (Part of T94T-50-B) 3 Red Lead (Part of T94T-50-B) 4 Positive Terminal (Part of 10655) Battery 6 Red Lead (Part of ) Rotunda Digital Volt-Ohmmeter or Equivalent 8 Black Lead (Part of ) 9 Negative Terminal (Part of 10655) 10 Black Lead (Part of T94T-50-B) 11 Connector (Part of T94T-50-B) (Attaches to CID Sensor) 10. Rotate engine two revolutions to take up slack in timing chain and return No. 1 cylinder to its compression stroke. 11. Verify that No. 1 cylinder is on its compression stroke (both valves closed). 12. NOTE: No. 1 cylinder must be at 26 degrees After Top Dead Center (ATDC) to set CID sensor. Continue to rotate the crankshaft until the new 26 degrees ATDC mark lines up with the timing pointer.

13 Page 13 of NOTE: The voltmeter will register battery voltage whenever the CID sensor closes and makes a complete circuit. Rotate the CID sensor and stop at the exact point where the sensor switches from 0 to 12 volts on the voltmeter. 14. NOTE: The final movement to set the CID sensor must be in a COUNTERCLOCKWISE direction. Rotate the CID sensor clockwise past the CID switching point (from 12 to 0 volts). 15. Rotate the CID sensor counterclockwise and stop at the exact point the voltmeter switches from 0 to 12 volts. 16. Tighten the CID sensor hold-down bolt to Nm (13-15 lb-ft) using Sensor Adjusting Wrench T94T A. 17. Disconnect the testing wiring harness and the voltmeter and proceed with Step 55 of Installation above.

ASSEMBLY Procedure revision date: 11/22/2001

ASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop