WALKWAYS and LADDERS. MEYER Tower Dryer ME1000S/SG-ME2650S/SG

Transcription

1 WALKWAYS and LADDERS MEYER Tower Dryer ME000S/SG-ME0S/SG May 0 MFH98-B

2 BROCK MEYER Walkways and Ladders WARNING! SAFETY First! Recognize SAFETY Information This symbol is used throughout this Manual to identify particular stages where the bin Contractor and/or Operator need to take special note and precautions regarding the danger described in these Instructions. Please read all the SAFETY information and the instructions completely prior to beginning the construction. This is the Safety-Alert Symbol. When you see this symbol on your equipment or in this Manual, be alert to the potential for personal injury. Signal words DANGER, WARNING, or CAUTION, are used with the Safety-Alert Symbol. Be sure to follow ALL National and Local Safety Standards governing each installation site. Understand Signal Words DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. WARNING indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. CAUTION indicates a hazardous situation which, if not avoided, MAY result in minor or moderate injury. Do not attach yourself to, or carry loose or dangling rope on structures near or adjacent to the Tower Dryer entry area. Loose rope or material can be suddenly sucked into the Dryer Fans (which may start automatically). This can cause equipment damage, severe personal injury or death. WORK SAFE! While some photographs in this Manual were taken at sites where certain PPE might not be required, Brock recommends using SAFETY equipment, especially hard hats and SAFETY harnesses at all installations. ALWAYS follow appropriate federal, state and local codes for PPR requirements. See Base Manual MFH98- for recommended PPE. WARNING! Use Fall Restraint/Arrest Systems When working on or inside a Tower Dryer at heights where fall hazards exist, use an adequate fall restraint or fall arrest system with a lifeline and harness, tied to a secure point. A proper fall arrest system should withstand,00 pounds [9 kg] of stress to prevent falling. A fall restraint system typically withstands less than 00 pounds and allows a limited fall of about ' [0]. To ease injury, it is recommended the falldistance on restraints be set at ' [ 89] maximum. Purchase and use secure lifelines and adequate fall restraint/arrest systems. Some facilities mandate that safety harnesses be used where there is risk of fall and/or entrapment. Failure to use fall restraint and/or arrest systems consistently when climbing or entering grain drying towers can cause serious injury or death. Table of Contents SAFETY First! Recognize SAFETY Information... Understand Signal Words DANGER, WARNING, CAUTION Use Fall Restraint/Arrest Systems... About This Manual... Definition of Terms and Symbols Measurements Identification of Parts and Hardware... Ladder SAFETY Procedures... Installations While the Tower Is on the Tower Trailer... - Install Walkways and Ship Loose Ladders-and-Cage on the Main Tower... Be Careful Stepping on the Horizontal Tower... Order of Walkway Installation... Bracket Installations... Walkway/ Catwalk Arms Floor Sections Upright Posts Handrails, Upper and Mid... MFH98-B

3 BROCK MEYER Walkways and Ladders Ladder-and-Cage Installation Basics, Horizontal Tower... - Outside Ladder Sections Ladder Splice... - Cage Hoop Halves... Lift the Tower to First Stage to Work Underneath... Types of Walkways... - Common Parts in Walkways... Full Walkway (-000) Partial Walkway (-000), All Models Eave Platform (-00) Roof Module All Models... - Eave Platform on the ME000S - ME00S... Outside Ladder-and-Cage Installation... - Ladder-and-Cage Parts Identification... Top Ladder Extension Through the Eave Platform... Extension Rail Bracing to the MEYER Roof... Outside Ladder Brackets to the Tower Ladder-and-Cage Sections Hoop Halves... 0 Cage Channels... Bottom Flared Cage Section... Outside Bottom Ladder (May Be Pre-Installed)... Locking Ladder Door Assembly Tie-Back Installation... Diagrams: Outside Walkways and Ladder-and-Cage... - Outside Ladder-and-Cage Packages... Outside Ladder Package Kit Numbers Chart... ME000S with Level Catwalk (-0008)... 8 ME00S with Level Catwalk (-0008)... 9 ME00S with or Level Catwalks (-00)...0 ME00S with Level Catwalk ( ME00S with or Level Catwalks (-00)... ME00S with Level Catwalk (-0008)... ME00S with or Level Catwalks (-00)... ME800S with Level Catwalks (-00088)... ME800S with Level Catwalks (-009)... ME000S with Level Catwalks (-00089)... ME000S with Level Catwalks (-00)... 8 ME000S with Level Catwalks (-008)... 9 ME00S with or Level Catwalks (-0009)...0 ME00S with Level Catwalks (-000)... ME0S with Level Catwalks (-00)... ME0S with Level Catwalks (-008)... ME0S with Level Catwalks (-008)... Inside Ladder Installations... - Inside Ladder Sections... Internal Service Platform Ladder Access... Top Inside Ladder Sections... Pre-Installed Inside Ladder Sections... Diagrams: Inside Ladders Inside Ladder Package Kit Numbers Chart... 8 ME000S... 9 ME00S... 0 ME00S... ME00S... ME800S... ME000S... ME00S... ME0S... MFH98-B

4 About This Manual BROCK MEYER Walkways and Ladders About This Manual IMPORTANT! CAUTION! IMPORTANT! The intent of this Manual is to help you follow step-by-step instructions for plumbing installations in the BROCK MEYER Dryer. Pay particular attention to all SAFETY Information in this Manual. Read and understand this Manual. Failure to follow proper procedures may cause damage to equipment or personal injury. Contact your Brock Dealer to replace this Manual should it become lost or damaged. Store it in a convenient place for easy reference. Definition of Terms and Symbols This Planning Symbol is used in areas where planning needs to take place before assembly and/or installation can continue. Horizontal, vertical, bottom, and top refer to the Dryer as it is standing. The symbols ('') equal inches and (') equals feet in English measurements. Measurements The symbols ('') equals inches and (') equals feet in English measurements. Metric measurements are shown in square brackets following the English measurement. For example: ' [. m] 90' [. m] Identification of Parts and Hardware Names for some components which have BROCK Part Numbers have been capitalized throughout this Manual to call attention to them. Parts and basic components are identified in Figures and their accompanying Tables as Items with a black number in white circle. See Figure below. Hardware is identified by a shaded circle and table item cell. Dimensions and lengths are noted with a white circle on an arrow or line, then identified with numeric values in a Figure Table. Pictures may vary slightly from actual components, which may have been modified for better fit or function. 8 8 U-0 Ladder Cap 8 U- Extension Rail '' [ ] 9-0 Nut, Flange /'' Washer, Flat / x /'' 9-0 Bolt, Hex Head /-8 x /'' Gr. Figure. Part and Hardware Identification Hardware Basics: Organize all hardware so the packages and buckets are easy to locate. When leaving for the day, remember where you are in the installation, which connections are tight, and which connections are loose. Always have a second person check the tightening on all Ladder and Walkway connections! This Pre-Assemble Symbol (left) suggests that a particular assembly can be finished ahead of time. Plan to sub-assemble and add hardware any parts that can be prior to installation. Make sure to use proper hardware. MFH98-B

5 BROCK MEYER Walkways and Ladders Ladder SAFETY Procedures Ladder SAFETY Procedures DANGER! Failure to comply with the following instructions may result in death or serious injury. IMPORTANT! The Ladder Section with the DANGER Decal (Part No. -90) in Figure at left must be installed as the BOTTOM Section of each Ladder.. The WORKING LOAD of the Ladder is 00 lbs [ kg]. Do not overload.. Never climb a damaged or improperly assembled Ladder. Before use, inspect the Ladder carefully for deterioration from chemicals or weather.. Keep the Ladder and Bin away from power lines and live electric wires.. Keep rungs free from slippery material such as ice, snow, mud, grease, manure, etc.. Wear slip-resistant shoes.. DO NOT USE LADDERS if you tire easily, or are subject to fainting spells, or use medicine or alcohol, or are physically handicapped.. FACE THE LADDER when ascending or descending. Maintain a firm grip. Center your body between Side Rails. 8. Discard and replace the Ladder if it is exposed to fire or damaging chemicals. 9. Never use the Ladder as a horizontal platform, plank or material hoist. 0.Never apply a side load. Never push or pull anything while on the Ladder..Never drop or apply an impact load to the Ladder..Never sit on the ends of Ladder Side Rails..Never use the Ladder as a scaffold.. Never use the Ladder when in poor health. DANGER! Figure. Ladder DANGER Decal -90 DANGER! DO NOT enter the Tower Dryer through the Manhole during the filling/ unloading operation or while the Dryer is in use! When the Dryer and auxiliary equipment are not LOCKED OUT, grain fill may start at any time without warning. DO NOT allow the Dryer to run while any adjustments are being made. SHUT OFF, LOCKOUT and TAGOUT all electrical power BEFORE working on or near the Dryer. Keep hands, feet, hair, and clothing away from all parts in motion. Failure to shut off, LOCKOUT and TAGOUT power to the Dryer will lead to personal injury or death. Figure. Slippage and Suffocation Hazards in Flowing Grain at Roof Module MFH98-B

6 Installations While the Tower Is on the Tower Trailer BROCK MEYER Walkways and Ladders Installations While the Tower Is on the Tower Trailer TOWARD TOWER TOP IMPORTANT! Install Walkways and Ship Loose Ladders-and-Cage on the Main Tower Orientation: Remember at all times that the actual TOP of the structure is toward the cab of the truck. The BOTTOM of the Tower is toward the back end of the truck. Install all possible Walkways and Side Ladder-and-Cages while the Tower trailer is horizontal. Refer to pages - for installation of /'' hardware on Walkways. DO NOT TIGHTEN Walkway Handrail or Post connections, as they must be leveled to vertical after the tower is raised. The lower Partial Walkway (-000, pages 0-) cannot be installed until the Tower is raised to vertical. Cage sections are not pre-installed. Hardware is located in the Ship Loose Bolt Kit. Refer to pages - for installation of Outside Ladder-and-Cage hardware/parts. TIGHTEN all Ladder and Cage connections. They will have to be re-tightened after the Tower is raised to vertical. Figure. BE CAREFUL Stepping on the Horizontal Tower Begin on ' stepladders, and continue the installation stepping only on the screen Stiffeners (pairs). Remember to step sideways so Screens will not be damaged. BE CAREFUL! STEP ONLY on Stringers/Stiffeners! DO NOT place your weight on the Screens. Step SIDEWAYS so the Screens will not be damaged. Use the next Stiffener to pull yourself up. Figure. Stand on Stringers Only MFH98-B

7 BROCK MEYER Walkways and Ladders Installations While the Tower Is on the Tower Trailer Order of Walkway Installation Walkway Arm Brackets Walkway Arms Floor Sections Vertical Posts Handrails See common parts on page. Figure. Right: Walkway Installation on Horizontal Tower Be cautious of personal SAFETY while working on the Tower in this position. Use an adequate number of ladders. Bracket Installations For your convenience, Walkway Arm Brackets (-000), Ladder Brackets, and some Ladder Sections are pre-installed. Check these Brackets for tightness when the Dryer is onsite. Figure 8. L/R Ladder Brackets on Module as Shipped Figure. Walkway Arm Bracket Pre-Installed on Intermediate Module and Horizontal Tower Module -000 Walkway Arm Bracket Tower, Horizontal -009 Ladder Bracket-LEFT -008 Ladder Bracket-RIGHT MFH98-B

8 Installations While the Tower Is on the Tower Trailer BROCK MEYER Walkways and Ladders Walkway/ Catwalk Arms Consecutive Walkway Arms are bolted into the eleventh and twelfth (th/th) bolt holes from the first set of bolts. There are ten (0) holes between Arms. Figure 9. Install Walkway Arms Attach the Walkway Arms, twelve () per Full Walkway, to the pre-installed Arm Brackets with three () /8 x '' galvanized Hex Head Bolts. Secure with Flange Nuts. Continue installing Arms around the Tower. Remaining Arms must be installed after the Tower is raised to vertical. All Arms must remain loose until all Walkway Floor Sections are attached. 8 MFH98-B

9 BROCK MEYER Walkways and Ladders Installations While the Tower Is on the Tower Trailer When the Walkway is tightened, tighten this Bolt first. Item Description Walkway Arm Bracket Walkway Arm Stringer / x '' HH Bolt galv /'' Flange Nut Figure 0. Walkway Arm Installation MFH98-B 9

10 Installations While the Tower Is on the Tower Trailer BROCK MEYER Walkways and Ladders IMPORTANT! Floor Sections Do not tighten Walkway Arms until all Floor Sections are connected to form a complete Walkway around the Tower.. Attach Walkway Floor sections. Drop in / x '' galvanized Hex Head Bolts, heads on top of the Walkway. Secure with Flange Nuts underneath. Be sure the Floor Panel (edge) is turned UP, toward the Tower TOP. Figure. Floor Sections TOWARD TOWER TOP * Item Description Walkway Arm Bracket Walkway Arm Floor Section / x ' HH Bolt galv /'' Flange Nut Figure. Walkway Floor Sections 0 MFH98-B

11 BROCK MEYER Walkways and Ladders Installations While the Tower Is on the Tower Trailer TOP VIEW TOWARD TOP UNDERSIDE VIEW Connect adjacent Floor Sections around the Tower as far as there is clearance to do so. Detail Detail Item Description Walkway Arm Bracket Walkway Arm Floor Section / x ' HH Bolt galv /'' Flange Nut TOWARD TOWER TOP Figure. Connect Adjacent Floor Sections MFH98-B

12 Installations While the Tower Is on the Tower Trailer BROCK MEYER Walkways and Ladders Upright Posts Attach the Upright Posts to the outer ends of the Walkway Arms with four () '' bolts. Secure with Flange Nuts. Figure. Walkway Posts: DO NOT TIGHTEN at this time! Item Description Walkway Arm Bracket Walkway Arm Floor Section / x ' HH Bolt galv /'' Flange Nut UNDERSIDE DETAIL Handrails, Upper and Mid When Vertical Posts are installed, attach Handrails and Handrails between Posts, Bolt heads inside the Post (same hardware). Repeat Handrail installation all the way around as far as you can. Figure. Top and Mid Handrails MFH98-B

13 BROCK MEYER Walkways and Ladders Installations While the Tower Is on the Tower Trailer Ladder-and-Cage Installation Basics, Horizontal Tower Outside Ladder Sections Check the tightness of factory-installed Ladder Brackets on the Tower, to be sure they are still tight after delivery. Some Ladder sections may already be installed in the Brackets with Locking Clips. Figure. Locate Pre-Installed Ladder Brackets and Ladder Sections on the Tower Detail Slide new Ladder Sections through the Ladder Brackets. Figure. Slide Ladder Sections Through Brackets Ladder Splice Ladder Sections (', ', ' and ') are bolted together using Ladder Rail Splicers (U-) with / x ' Gr. Hex Head Bolts and Flange Nuts. U- Ladder Rail Splicer varies Side Ladder 9-00 Bolt, HHBS /-8 x /'' Gr Nut, Flange /''-8 Figure 8. Ladder Rail Splice MFH98-B

14 Installations While the Tower Is on the Tower Trailer BROCK MEYER Walkways and Ladders Secure Ladder Sections with Locking Clips (in the Bolt Kit). Be sure the Ladder DANGER Decal shown in Figure is right side up. Figure 9. Locking Clips and Splices Cage Hoop Halves Attach Cage Hoop Halves to the Ladder rail on each side with Locking Clips. Attach the Hoop Halves in the middle front with hardware from the Bolt Kit. See Details on pages 0-. Figure 0. Cage Installation MFH98-B

15 BROCK MEYER Walkways and Ladders Installations While the Tower Is on the Tower Trailer IMPORTANT! Lift the Tower to First Stage to Work Underneath After all possible Walkways and Ladder-and-Cage sections have been installed to the horizontal Tower Module on the Tower trailer, lift the Tower to the FIRST STAGE. FIRST STAGE is a partially raised position that allows the remainder of the full Access Platforms to be installed. After the remaining Access Platform(s) have been installed, tighten the Platform and Arms. DO NOT TIGHTEN Walkway Arms until all Floor Sections are connected to make a complete Walkway. DO NOT tighten the Handrails or Upright Posts. On the ME000S through 00S Models, the Tower Module and Roof Module are shipped preassembled together and as one unit on the Tower trailer. Some Eave Platform assembly can be done while the lift truck is in First Stage lift. Remaining Ladder-and- Cage, and Partial Walkway installations are done after the Tower and Modules are raised to vertical. WARNING! Use CAUTION when raising the Tower section to First Stage. Be sure to use all locking pins specified. Use CAUTION when raising the Tower section to full height. Stand clear! Follow all SAFETY Decals. DO NOT attempt to MOVE the truck with the hoist/tower in a raised position! Protect or LOCK THE CONTROLS so that no hoist movement can be made unintentionally. Failure to follow this instruction could cause death, serious injury, and/or equipment damage. Figure. Install Walkways at Tower Trailer FIRST STAGE Lift MFH98-B

16 Types of Walkways BROCK MEYER Walkways and Ladders Types of Walkways 0 9 Figure. Eave Platform ( Floor Sections) Figure. Partial Walkway ( Floor Sections) -000 Figure. Full OUTSIDE Walkway ( Floor Sections) -000 MFH98-B

17 BROCK MEYER Walkways and Ladders Types of Walkways Common Parts in Walkways page. Walkway Common Parts Figure. Eave Platform -00 FRONT VIEW Full Outside Walkway Partial Walkway Qty. Qty. Qty Walkway Floor Section.'' -000 Handrail Walkway Arm -000 Walkway Arm Bracket** -000 Walkway Arm Bracket LONG -00 Brace, Roof Handrail '' -00 Brace, Roof Handrail RIGHT '' 8-00 Brace, Roof Handrail LEFT '' (not shown) 9-00 Platform Roof Mount Rail, TPH /8'' -000 Endrail/Handrail External -000 Vertical Post, /'' * Screw, /-8 x ' HWH 98 0 Eave Platform *-0000 Nut, Flange /''-8 Serr *Hardware in Ship Loose Bolt Kit **This Bracket pre-installed on Tower/Modules MFH98-B

18 Types of Walkways BROCK MEYER Walkways and Ladders FULL Walkway (-000) FULL Walkways are installed all the way around the Dryer with an opening for the Ladder-and-Cage. There may be several outside Walkways, depending on the Model. Refer to Outside Ladder Diagrams on page - for the number and placement of Walkways on each different MEYER model. Figure. Full Outside Walkway ( Floor Sections) -000 Qty Walkway Floor Section.'' -000 Handrail -000 Walkway Arm -000 Walkway Arm Bracket** -000 Vertical Post, Walkway /'' * Screw, /-8 x '' HWH 98 *-0000 Nut, Flange /''-8 Serr. 98 *Hardware in Ship Loose Bolt Kit **This Bracket pre-installed on Tower/Modules * ** TOP VIEW Left, Figure. ME00, One () Platform 8 MFH98-B

19 BROCK MEYER Walkways and Ladders Types of Walkways First Level Walkway -000 ONE PLATFORM: Models ME000S-00S Qty Walkway Floor Section.'' -000 Handrail -000 Walkway Arm -000 Walkway Arm Bracket -000 Vertical Post /'' Bolt, /-8 x '' HWH Whizlock Nut, /''-8 HWH Flange 98 TWO Walkway Assembly -000 TWO PLATFORMS: Models ME800S-000S Standard and ME000-00S Optional Qty Walkway Floor Section.'' -000 Handrail Walkway Arm -000 Walkway Arm Bracket -000 Vertical Post, /'' *Bolt, /-8 x '' HWH Whizlock *Nut, /''-8 HWH Flange 9 *Located in the Ship Loose Bolt Kit THREE Walkway Assembly -000 THREE PLATFORMS: Models ME00S Standard and ME00S, ME S Optional Qty Walkway Floor Section.'''' -000 Handrail -000 Walkway Arm -000 Walkway Arm Bracket -000 Vertical Post, /'' *Bolt, /-8 x '' HWH Whizlock *Nut, /''-8 HWH Flange 9 *Located in the Ship Loose Bolt Kit Figure 8A. Three Platforms Figure 8B. Five Platforms MFH98-B 9

20 Types of Walkways BROCK MEYER Walkways and Ladders PARTIAL Walkway (-000), All Models Locate the End Handrail Brace (Item ) one () Screen directly above Use Inside Ladder Brace (Item, -9) on the inside Screen as a reference. On the corresponding outside Screen (see Top View), locate the second and third (nd/ rd) bolt counter-clockwise from the Screen flange to attach the first Walkway Arm. Hardware is located in the Ship Loose Bolt Kit. The End Brace of the left Walkway Floor Panel will mount just outside the Ladder rail below the Hi-Limit Box. There will be ten (0) bolts between Ladder Brackets. PARTIAL Walkway Location Chart Model Height* Module ME0S Screen ME00S Screen ME00S Screen ME000S Screen ME800S Screen ME00S Screen B ME00S Screen B ME00S Screen B ME000S Screen A *Counting up from bottom of Module 8 * ** TOP VIEW Figure 9. Partial Walkway (-000) 0 MFH98-B

21 BROCK MEYER Walkways and Ladders Types of Walkways Figure 0. Partial Walkway Views The Partial Walkway is built in this location after the Tower Module has been raised and connected to the Unload Module. Qty Walkway Floor Section.'' -000 Handrail Walkway Arm -000 Walkway Arm Bracket** -000 Walkway Arm Bracket LONG -000 Endrail/Handrail External -000 Vertical Post, /'' * Screw, /-8 x '' HWH *-0000 Nut, Flange /''-8 Serr Ladder Chord MFH98-B

22 Types of Walkways BROCK MEYER Walkways and Ladders Eave Platform (-00), Roof Module, All Models Figure. Eave Platform Ladder Brackets: Counting from the left/ right, LEFT Ladder Brackets attach at the th and th Brackets holes from the Wall post. RIGHT Ladder Brackets attach at the 8th and 9th holes. Qty Walkway Floor Section.'' -000 Handrail -000 Walkway Arm -000 Walkway Arm Bracket** -00 Brace, Roof Handrail '' -00 Brace, Roof Handrail RIGHT '' 8-00 Brace, Roof Handrail LEFT '' 9-00 Platform Roof Mount Rail, TPH /8'' -000 Endrail/Handrail External -000 Vertical Post, /'' * Screw, /-8 x '' HWH 0 *-0000 Nut, Flange /''-8 Serr Ladder Extension: Pages - MFH98-B

23 BROCK MEYER Walkways and Ladders Types of Walkways Install supports for the upright (both sides). Install the U-shaped Roof Mount Bracket (Item 9) over the Roof Rib where the electrical conduit routes and exits down the Module Figure. Roof Mount Brackets. Connect the Roof Upright Brace (Item ) to the top of the Bracket. Connect the top End Handrail (Item ) to the top of the Brace Figure. Roof Mount End/Back Connections MFH98-B

24 Types of Walkways BROCK MEYER Walkways and Ladders Eave Platform on the ME000S Through ME00S On the MEYER ME000S through ME00S Models, the Tower Module and Roof Module are shipped pre-assembled together and as one unit on the lift truck. Some Eave Platform assembly can be done while the lift truck is in First Stage lift. 8 9 Figure. Eave Platform Front View MFH98-B

25 BROCK MEYER Walkways and Ladders Outside Ladder and Cage Installation Outside Ladder and Cage Installation Ladder-and-Cage Parts Identification A B U-9 Locking Clip Assembly -000 Inside Ladder Bracket (see page ) U- Ladder Rail Splicer U-0000 ' [ 9] Ladder Section U-0000 ' [ ] Ladder Section U-0000 ' [ 89] Ladder Section A B Ladder Bracket-LEFT Ladder Bracket-RIGHT U-0 Ladder Cap U- Extension Rail Brace Bracket 8 U- Extension Rail '' [ ] O.A. 9 U-9 Extension Rail Spacer Tube 0 U- Cage Hoop Half Cage Channel '' [ ] (BUNDLE # 988) field-cut Cage Channel '' SHORT (not shown) U-0 Cage Hoop Expander -90 Ladder DANGER Decal ( per Section) 9- BACK Tube, /8'' 9- SIDE Tube 8'' 9-00 Bolt, / x /'' BS Gr /'' Flange Nut 9-00 Bolt, / x /'' Hex Head BS Gr /'' Hex Nut Bolt, /'' x '' Hex Head Gr Bolt, Hex Head /-8 x /'' Gr Washer, Flat / x /'' 9-0 Bolt, Hex Head /-8 x /'' Gr. 9-0 Washer, Weatherseal /'' Figure. Ladder and Cage Parts MFH98-B

26 Outside Ladder and Cage Installation BROCK MEYER Walkways and Ladders Top Ladder Extension Through the Eave Platform Build Ladder Extension Rails (Kit 9-099, All Models) Install a pair of '' [ ] Ladder Extension Rails (Item 8) to the ' Top Ladder Section (Item ) at the Eave. On both the left and right sides of the top Ladder Section, add an Extension Rail. Insert the upper / x /'' Hex Head Bolt (Item ) from inside the Ladder Section through the Ladder Cap (Item ) and Spacer Tube (Item 9). Put a Flange Nut (Item ) on the outside of the Extension Rail. Add the same Hardware and Spacer Tube for the lower connection below the Ladder Rung. See Detail B below. Top ends of the Side Ladder and Extension Rail are finished with a Ladder Cap. Secure as shown in Detail A below, adding a ga. Washer (Item 8). Use a / x /'' HHBS Bolt (Item ) on top, with a Weatherseal Washer (Item ) and a Hex Nut (Item ). Detail A FRONT VIEW B 9 Detail B U Ladder Section ' A B -009 Ladder Bracket LEFT -008 Ladder Bracket RIGHT U-0 Ladder Cap 8 U- Extension Rail '' [ ] O.A. 9 U-9 Extension Rail Spacer Tube 9-00 Bolt, HHBS /-8 x /'' Gr Nut, Flange /'' Nut, Hex /'' 9-0 Bolt, Hex Head /-8 x /'' Gr Washer, Flat / x /'' 9-0 Bolt, Hex Head /-8 x /'' Gr. Figure. () Ladder Extensions on Top Ladder Section MFH98-B

27 BROCK MEYER Walkways and Ladders Outside Ladder and Cage Installation Extension Rail Bracing to the MEYER Roof To brace the Extension Rails to the Roof, bolt the Brace Tubes as shown below. Bolt the flatter ends of two () Ladder Back Brace Tubes (Item ) to the top of the Ladder Extension Rails (Item 8) as shown in Detail A below. Bolt the single Ladder Side Brace Tube (Item ) to the Ladder Extension Rails as shown in Detail B below Detail B 9 8 Back Brace Detail A 8 Side Brace Detail B 9 OR 0 8 Detail D Brace-to-Roof Detail C Secure tops ends of Braces with a Flange Nut (Item 9) on a Brace Bracket (Item ) and Locking Clip (Item ) as shown in Detail D above. Bottom ends of Braces connect to the Roof Module. Field drill. Use a / x /'' HHBS Bolt (Item ) on top, with a Weatherseal Washer (Item ) between the Brace and Roof, and a Hex Nut (Item ) under the Rib. See Detail C above. Qty U-0000 Ladder Assy, ' U- Rail, Ladder Extension Cage U-9 Tube, Cage Ext Rail Spacer U-9 Ladder Locking Clip Assy U- Extension Rail Brace Bracket 9- BACK Tube, /8'' 9- SIDE Tube 8'' 9-00 Bolt, HHBS /-8 x /'' Gr Nut, Flange /'' Nut, Hex /'' Washer, Weatherseal /'' Figure. Bracing Ladder Extensions on Top Ladder Section Through the Eave Platform MFH98-B

28 Outside Ladder and Cage Installation BROCK MEYER Walkways and Ladders WARNING! IMPORTANT! Outside Ladder Brackets to the Tower Ladder installations MUST use all specified connecting Brackets to maintain SAFETY. Failure to follow specific Hardware instructions during assembly could result in serious operator injury and /or structural damage. Install all Ladder sections with the ROUGH side of the rungs facing UPWARD and with DANGER Decals right-side-up at the bottom of each Ladder section. varies Side Ladder A -009 Ladder Bracket LEFT Top B -008 Ladder Bracket RIGHT Top varies Grain Sampler Tube Top Ladder ends: Counting from the left/right, LEFT Ladder Brackets attach at the th and th Brackets holes from the Wall post. RIGHT Ladder Brackets attach at the 9th and 0th holes. A B Detail A Detail B A B DETAIL C DETAIL A Mid Ladder areas: Counting from the left/right, LEFT Ladder Brackets attach at the 0th and th Brackets holes from the Wall post. RIGHT Ladder Brackets attach at the th and th holes. Figure 8. Outside Ladder Brackets 8 MFH98-B

29 BROCK MEYER Walkways and Ladders Outside Ladder and Cage Installation A B Ladder area at the upper JIC Box: Counting from the left/right, LEFT Ladder Brackets attach at the rd and th Brackets holes from the Wall post. RIGHT Ladder Brackets attach at the th and 8th holes. varies Side Ladder A -009 Ladder Bracket LEFT Top B -008 Ladder Bracket RIGHT Top A B Figure 9. Outside Ladder Brackets MFH98-B 9

30 Outside Ladder and Cage Installation BROCK MEYER Walkways and Ladders Ladder-and-Cage Sections Ladder-and-Cage Sections are installed approximately every '' [ 8]. Connect the Hoop ends to the front side of the Ladder Extension Rail (refer to Page ) with Locking Clip assemblies (Item ), secured on the outside with Flange Nuts. OUTSIDE VIEW 0 Hoop Halves The Cage is begun by joining two () Hoop Halves (Item 0), even with the top of the Ladder Extension Rails, above the Eave. See Detail A. Overlap the Hoop Halves by aligning the three front holes. See Detail B. Connect with / x /'' Hex Head Bin Seal Bolts, Bolt heads inside, and /'' Hex Nuts, leaving a Bolt out of the center hole. Tighten Bolts from the head side. Detail A INSIDE VIEW Detail A Detail B 8 0 Detail B 0 Build the top Hoop. Figure 0. Cage Start at Top of Extension Rails U-9 Locking Clip Assembly varies Ladder Section U-0 Ladder Cap 8 U- Extension Rail '' [ ] O.A. 0 U- Cage Hoop Half Cage Channel '' [ ] 9-00 Bolt, / x /'' BS Gr /'' Flange Nut /'' Hex Nut Build the second Hoop. Once there are two () complete Hoops, they can be connected with Cage Channels. 0 Figure. Second Hoop 0 MFH98-B

31 BROCK MEYER Walkways and Ladders Outside Ladder and Cage Installation Cage Channels Vertical Cage Channels (Item ) are shipped in bundles of eight (8). The Cage has seven () Channels around. Channels connect outside the Hoop Halves with the same hardware as above, Bolt heads inside. Tighten Bolts from the head side. Field-cut Channels as needed. U-9 Locking Clip Assembly U- Ladder Rail Splicer varies Ladder Section U-0 Ladder Cap 0 U- Cage Hoop Half Cage Channel '' [ ] 9-00 Bolt, / x /'' BS Gr /'' Flange Nut /'' Hex Nut Figure. Building the Cage with Hoop Halves and Channels Continue building the Ladder and Cage downward. Ladder Sections are bolted together using Ladder Rail Splicers U- (Item ), / x /" Gr. Hex Head Bolts and Flange Nuts (Items and ). B 0 A Splice Detail (Outside View) 0 Figure. Outside Ladder Brackets MFH98-B

32 Outside Ladder and Cage Installation BROCK MEYER Walkways and Ladders Bottom Flared Cage Section Build the bottom Flare Hoop by connecting the two () Hoop Halves (Item 0) with an Expander section (Item ) in between, using / x /'' Hex Head Bin Seal Bolts (heads inside) and Hex Nuts. The ends of bottom Hoop Halves attach to the back edge (next to the bin wall) of the Ladder Rail with a Locking Clip Assembly, with Bolt Heads inside. 0 0 U-9 Locking Clip Assembly varies Ladder Section U-0 Ladder Cap 0 U- Cage Hoop Half Cage Channel '' [ ] U-0 Cage Hoop Expander 9-00 Bolt, / x /'' BS Gr /'' Flange Nut /'' Hex Nut TOP HOOP CONNECTION DETAIL Figure. Bottom Flared Section FLARE HOOP CONNECTION DETAIL FRONT VIEW MFH98-B

33 BROCK MEYER Walkways and Ladders Outside Ladder and Cage Installation Outside Bottom Ladder (May Be Pre-Installed) The Ladder section on the Unload Base Module will be needed for access throughout the installation. Figure. Bottom Ladder and Access Door Figure.. Bottom Ladder at Unload Module MFH98-B

34 Outside Ladder and Cage Installation BROCK MEYER Walkways and Ladders Locking Ladder Door Assembly 9-0 Install locking devices to reduce the risk of unauthorized access at tower points of entry. This Door is installed on the bottom Outside Ladder section at the Unload. Plan whether your Ladder Door is to be LEFT- or RIGHT-opening before attaching the Door assembly to the Ladder. The Door may be secured with a padlock (not included). Figure. Locking Ladder Door 9-0. Bolt the Upper and Lower Hinge Assemblies (Item ) to the Door (Item ) with two /8'' Carriage Bolts (Item ) (heads outside) and Lock Nuts (Item 8) inside. See Detail A at right.. Install the Handle (Item ) on the Door with two /'' Bin Seal Bolts (Item ), heads outside and Lock Nuts (Item 8) inside.. Bolt the two Hinge Assemblies to the Ladder Rail with two /'' Hex Head Bolts (Item ), heads toward inside of the Ladder, and Lock Nuts (Item 8). See Detail A.. Bolt the Lock Bracket (Item ) to the opposite Ladder Rail. It is installed either above or below the Door Handle. Use two /'' Hex Head Bolts (Item ), heads inside the Ladder, and Lock Nuts (Item 8). The Lock Bracket flange should be turned toward the back (bin side) of the Ladder, to line up with one of the round holes in the Door. Detail B Detail A Qty Door, Bin Ladder 9-0 Hinge Assembly 9-00 Bracket -9 Handle Ladder 88 / - 8 x /8'' Carriage Bolt, Gr. - / - 8 x /8'' Hex Head Bolt, Gr / - 8 x /'' Bin Seal Bolt, Gr /'' - 8 Lock Nut 8 9 Figure 8. Locking Ladder Door MFH98-B

35 BROCK MEYER Walkways and Ladders Outside Ladder and Cage Installation Item Part No. Tie-Back Hardware Qty. B Dryer Sidewall D Door (open) - Chain ' 0 S-Hook - Spring Extension 9-00 /'' Eyebolt 9-0 /'' Weatherseal Washer /'' Hex Nut FRONT VIEW Figure 9. Lock Bracket Detail Tie-Back Installation: The Door in its open position uses a Tie-Back Chain/Spring assembly.. Attach an S-Hook to each end of the Tie-Back Chain. Put one S-Hook in a Lock hole in the Door. Adjust length and tension.. Locate the bin vertical seam nearest the hinge side of the Ladder, (or fielddrill a hole nearer the Ladder). In feed bins, use any available hole in a Ladder Standoff Rail, X-Brace, or Leg.. Replace regular seam hardware, from the outside, with: the Eyebolt, /'' Hex Nut, and Weatherseal Washer. Use a second Hex Nut inside. To lock, close the Door. Insert a padlock or locking device (not provided). To reduce the risk of unauthorized entry to the Dryer, the Owner/ Operator should install PADLOCKS wherever appropriate, especially on Access Doors in the Cooling Floor / Plenum, the Roof Manhole, and any other point of entry. Install Locks on Electrical Cabinets and the Disconnect Handle. Figure 0. Chain and Eyebolt Detail B SIDE VIEW OUTSIDE D FRONT VIEW B Figure. Padlock Suggestion (Owner-Supplied) for Locking Ladder Door and Disconnect Handle LOOP MFH98-B

36 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage Outside Ladder-and-Cage Packages Tower Description Part No. ME000 with Level Walkway ME00 with Level Walkway ME00 with or Level Walkways -00 ME00 with Level Walkway -00 ME00 with or Level Walkways -00 ME00 with Level Walkway ME00 with or Level Walkways -00 ME800 with Level Walkways ME800 with Level Walkways -009 ME000 with Level Walkways ME000 with Level Walkways -00 ME000 with Level Walkways -008 ME00 with or Level Walkways ME00 with Level Walkways -000 ME0 with Level Walkways -00 ME0 with Level Walkways -008 ME0 with Level Walkways -008 MFH98-B

37 MFH98-B MEYER Model: Outside Ladder Package Kit No Number of Tower Walkway Levels or or or or U- Cage Hoop Half U-0 Cage Hoop Expander 988 Channel Bundle of Kit, Ladder Cage Extension -008 Ladder Standoff Bracket-RIGHT Ladder Standoff Bracket-LEFT U-9 Locking Clip Assembly U- Ladder Rail Splicer U-0000 ' Ladder Assembly U-0000 ' Ladder Assembly U-0000 ' Ladder Assembly *-0000 Nut, /''-8 Flange HWH Serr * Bolt, /-8 x '' HWH Whizlock zc * Additional quantities in Ship Loose Bolt Kit below Ship Loose Kits U- Cage Hoop Half U-0 Cage Hoop Expander 988 Channel Bundle of Kit, Ladder Cage Extension -008 Ladder Standoff Bracket-RIGHT Ladder Standoff Bracket-LEFT U-9 Locking Clip Assembly U- Ladder Rail Splicer U-0000 ' Ladder Assembly U-0000 ' Ladder Assembly 8 0 U-0000 ' Ladder Assembly -000 Bottom Ladder (for Unload Module) -000G0 Ship Loose Bolt Kit G0 G0 G0/ G0 G0 G0 G0 G0 G0/ G0 G08 G Nut, /''-8 Flange HWH Serr Bolt, /-8 x '' HWH Whizlock zc BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage

38 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders ME000S 0 9 U-0000 ' [ 9] Ladder Section U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside ladder 0 0 Figure. Outside Ladders and Cages on ME000S with Level Catwalk (-0008) 8 MFH98-B

39 BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage ME00S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE All Ladders, Brackets and Splices from this point down, both sides SHIP LOOSE Brackets and Ladders this section only 9 U-0000 ' [ 9] Ladder Section U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside ladder 0 9 * Figure. Outside Ladders and Cages on ME00S with Level Catwalk (-0008) MFH98-B 9

40 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders ME00S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE All Ladders, Brackets and Splices from this point down, both sides 8 SHIP LOOSE Brackets and Ladders this section only U-0000 ' [ 9] Ladder Section U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside ladder 0 9 * Figure. Outside Ladders and Cages on ME00S with or Level Catwalks (-00) 0 MFH98-B

41 BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage ME00S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE Brackets and Ladders this section only U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside ladder 0 SHIP LOOSE All Ladders, Brackets and Splices from this point DOWN, BOTH SIDES 9 * Figure. Outside Ladders and Cages on ME00S with Level Catwalk (-00) MFH98-B

42 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders ME00S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE Brackets and Ladder this section only U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder 0 SHIP LOOSE All Ladders, Brackets and Splices from this point DOWN, BOTH SIDES 9 * Figure. Outside Ladders and Cages on ME00S with or Level Catwalks (-00) MFH98-B

43 BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage ME00S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE Brackets and Ladder this section only U-0000 ' [ 9] Ladder Section U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder 0 SHIP LOOSE All Ladders, Brackets and Splices from this point DOWN, BOTH SIDES Figure. Outside Ladders and Cages on ME00S with Level Catwalk (-0008) MFH98-B * 9

44 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders ME00S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE Brackets and Ladder this section only Ladder Section, ' U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder 0 SHIP LOOSE All Ladders, Brackets and Splices from this point DOWN, BOTH SIDES 0 0 This Bracket to be installed on the Tower Figure. Outside Ladders and Cages on ME00S with or Level Catwalks (-00) * 9 MFH98-B

45 BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage ME800S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE Ladders from this point UP 0 Ladder Section, U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder SHIP LOOSE All Ladders, Brackets and Splices from this point DOWN, BOTH SIDES 0 Figure 8. Outside Ladders and Cages on ME800S with Level Catwalks (-00088) * 9 MFH98-B

46 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders ME800S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE Ladders from this point UP SHIP LOOSE All Ladders, Brackets and Splices from this point DOWN, BOTH SIDES SHIP LOOSE Ladder Section, U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder 0 * Figure 9. Outside Ladders and Cages on ME800S with Level Catwalks (option) (-009) 9 MFH98-B

47 BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage ME000S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE Ladder Bracket here 0 SHIP LOOSE Brackets and Ladders from this point UP, BOTH SIDES U-0000 ' [ 9] Ladder Section U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder SHIP LOOSE All Ladders, Brackets and Splices from this point DOWN, BOTH 0 8 Figure 0. Outside Ladders and Cages on ME000S with Level Catwalks (-00089) * 9 MFH98-B

48 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders ME000S 0 SHIP LOOSE Ladder Bracket here 0 SHIP LOOSE Ladder Bracket here NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE All Ladders from this point UP, BOTH SIDES U-0000 ' [ 9] Ladder Section U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder SHIP LOOSE All Ladders, Brackets and Splices from this point DOWN, BOTH SIDES Figure. Outside Ladders and Cages on ME000S with Level Catwalks (-00) * 8 MFH98-B

49 BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage ME000S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE All Ladders from this point UP, BOTH SIDES U-0000 ' [ 9] Ladder Section U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder SHIP LOOSE All Ladders, Brackets and Splices from this point DOWN, BOTH SIDES Figure. Outside Ladders and Cages on ME000S with Level Catwalks (-008) * MFH98-B 9

50 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders ME00S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) 0 0 SHIP LOOSE Ladders, Brackets here 0 All Ladders, Brackets and Splices SHIP LOOSE from this point DOWN, BOTH SIDES 0 * All Ladders, Brackets and Splices SHIP LOOSE from this point UP, BOTH SIDES U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder 9 Figure. Outside Ladders and Cages on ME00S with or Catwalks (-0009) 0 MFH98-B

51 BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage ME00S Catwalks NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) 0 0 SHIP LOOSE Ladders, Brackets here 0 All Ladders, Brackets and Splices SHIP LOOSE from this point DOWN, BOTH SIDES 0 All Ladders, Brackets and Splices SHIP LOOSE from this point UP, BOTH SIDES U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder Figure. Outside Ladders and Cages on ME00 with Catwalks (-000) MFH98-B * 9

52 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders ME0S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) Shipping Tower SHIP LOOSE SHIP LOOSE from this point UP U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder 0 All Ladders, Brackets and Splices SHIP LOOSE from this point DOWN, BOTH SIDES 0 Figure. Outside Ladders and Cages on ME0S with Catwalks (-00) * 9 * All Ladders, Brackets and Splices shown above SHIP LOOSE; bottom () ' Ladders (*) called out in Base assembly. MFH98-B

53 BROCK MEYER Walkways and Ladders Diagrams: Outside Walkways and Ladder-and-Cage ME0S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) SHIP LOOSE from this point UP U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder 0 All Ladders, Brackets and Splices SHIP LOOSE from this point DOWN, BOTH SIDES * 9 SHIP LOOSE from here down 0 Figure. Outside Ladders and Cages on ME0S with Catwalks (-0008) * All Ladders, Brackets and Splices shown above SHIP LOOSE; bottom () ' Ladders (*) called out in Base assembly. MFH98-B

54 Diagrams: Outside Walkways and Ladder-and-Cage BROCK MEYER Walkways and Ladders ME0S NOTE: This group of Ladder and Safety Cage parts is located at the Leg position (shown here for clarity) U-0000 ' [ ] Ladder Section * U-0000 ' [ ] Ladder Section (called out, loose assy.) U-0000 ' [ 89] Ladder Section U- Cage Hoop (Half) Cage Channel '' [] 8 Cage Channel '' 9 U-0 Cage Hoop Expander 0 varies Side Ladder Bracket Partial Walkway -000 Full Walkway -00 Eave Platform -000 Walkway Arm Walk-Through Leg '' Ladder Position varies Inside Ladder All Ladders, Brackets and Splices SHIP LOOSE from this point UP, BOTH SIDES All Ladders, Brackets and Splices SHIP LOOSE from this point DOWN, BOTH SIDES 9 * 0 All Ladders, Brackets and Splices shown above SHIP LOOSE; bottom () ' Ladders (*) called out in Base assembly. Figure. Outside Ladders and Cages on ME0S with Catwalks (-0008) MFH98-B

55 BROCK MEYER Walkways and Ladders Inside Ladder Installations Inside Ladder Installations WARNING! Inside Ladder Sections Inside Ladder sections are mounted on Ladder Chords. While the same Locking Clip Assembly is used to attach the Ladder Bracket to the Ladder Rail, the Inside Ladder Bracket -000 differs from Outside Brackets. Be sure Ladder DANGER Decal -90 (left) on each Ship-Loose Ladder section to be installed is readable right-side-up when the Tower is upright. Ladder installations MUST use all specified connecting Brackets to maintain SAFETY. Failure to follow specific Hardware instructions during assembly could result in serious operator injury and /or structural damage. Attach the Ladder to the Bracket on both sides, using the Ladder Clips. IMPORTANT! Install all Ladder sections with the ROUGH side of the rungs facing UPWARD and with DANGER Decals right-sideup at the bottom of each Ladder section. Splice sections together. See Figure 8 on page. varies Inside Ladder (location) -000 Inside Ladder Bracket varies Inside Screen -000 Inside Ladder Clip U-9 Locking Clip Figure 8. Inside Ladder Bracket and Ladder Clips MFH98-B

56 Inside Ladder Installations BROCK MEYER Walkways and Ladders Internal Service Platform Ladder Access Continue the Inside Ladder-and-Cage installation through the Inside Service Platform opening in the Tower. Figure 9. Inside Ladder Through the Service Platform Opening Figure 0. Inside Ladder with Cage Finish the access area by installing Safety Rails. Figure. Rails at Service Platform Ladder Access -00 Post, Work Platform -00 Handrail, Work Platform MFH98-B

57 BROCK MEYER Walkways and Ladders Inside Ladder Installations IMPORTANT! Top Inside Ladder Sections You must field-install the Ladder section above the # Inside Service Platform. There are four () Ladder splices above and below the Platform. Figure. Top Inside Ladder Installation in the Tower Special Note on Model 0: The 0'' distance between the Inside Service Platform and where the Inside Ladder must be mounted is a difficult reach. take a ' or ' stepladder up with you to help make the task easier. Pre-Installed Inside Ladder Sections The Upper Inside Ladder section is factoryinstalled, as well as the Ladder section attached to the Air Duct. Item Description Ladder Section Air Duct Duct Access Door Bracket -008 Figure. Inside Ladder at Air Duct (LP Model shown), Pre-Installed MFH98-B

58 Diagrams: Inside Ladders BROCK MEYER Walkways and Ladders Diagrams: Inside Ladders MEYER Model: INSIDE Ladder Package Kit Number Bracket Ladder Attachment U-9 Locking Clip Assembly U- Ladder Rail Splicer U-0000 ' Ladder Assembly U-0000 ' Ladder Assembly U-0000 ' Ladder Assembly *Bolt, /-8 x '' HWH Whizlock * Bolt, /-8 x /8'' Hex Fla 8 0 *-0000 Nut, /''-8 Flange HWH Serr. 8 0 * Additional quantities in Ship Loose Bolt Kit below Ship Loose Kits -000 Bracket Ladder Attachment U-9 Locking Clip Assembly U- Ladder Rail Splicer 8 0 U-0000 ' Ladder Assembly U-0000 ' Ladder Assembly U-0000 ' Ladder Assembly U-0000 ' Ladder Assembly Ship Loose Bolt Kit Bolt, /-8 x /8'' Hex Fla Nut, /''-8 Flange HWH Serr '' 8 MFH98-B

59 BROCK MEYER Walkways and Ladders Diagrams: Inside Ladders ME000S -00 Ladder Chord, 0'' -009 Ladder Chord, '' U-0000 ' [9] Ladder Section U-0000 ' [ 9] Ladder Section U-0000 ' [ ] Ladder Section -000 Inside Ladder Bracket 8 U-9 Locking Clip Assembly 0 Ladder should be as close as possible to the Plenum Access Door without interference, when the Door is open. Plenum Floor Inside Ladder (position) Plenum Access Door Plumbing side Main Entrance on Base Module *In SHIP LOOSE Package 0 * * * * Figure. Inside Ladder Location, Model ME000S (-00) Figure. Inside Ladder Location, Top View, Typical All Models MFH98-B 9