LAD-series Portable Warehouse Ladders, 6-12 Steps Instruction Manual

Size: px
Start display at page:

Download "LAD-series Portable Warehouse Ladders, 6-12 Steps Instruction Manual"

Transcription

1 Rev. 3/3/07 LAD (6- STEPS), MANUAL VESTIL MANUFACTURING CORP. 999 North Wayne Street, P.O. Box 507, Angola, IN Telephone: (60) or- Toll Free (800) Fax: (60) HU U LAD-series Portable Warehouse Ladders, 6- Steps Instruction Manual Receiving instructions: After delivery, remove the packaging from the product. Inspect the product closely to determine whether it sustained damage during transport. If damage is discovered, record a complete description of it on the bill of lading. If the product is undamaged, discard the packaging. NOTE: The end-user is solely responsible for confirming that product design, installation, use, and maintenance comply with laws, regulations, codes, and mandatory standards applied where the product is used. Table of Contents Signal words. Hazards of improper use.... Specifications... 3 FIGS. -8: Exploded parts diagrams and bills of materials 4 - Assembly instructions - 6 Using the ladder..6 Inspections & Maintenance.. 6 Labeling diagram... 7 Limited warranty Copyright 07 Vestil Manufacturing Co. Page of 8

2 Rev. 3/3/07 LAD (6- STEPS), MANUAL Signal Words: This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the probable seriousness of injuries that might occur if the product is misused in the ways described. Other signal words call attention to uses of the product likely cause property damage. The signal words used in this manual appear below along with the meaning of each word: Identifies a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS INJURY. Use of this signal word is limited to the most extreme situations. Identifies a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS INJURY. Indicates a hazardous situation which, if not avoided, COULD result in MINOR or MODERATE injury. Identifies practices likely to result in product/property damage, such as operation that might damage the ladder. Hazards of Improper Use: Vestil strives to identify foreseeable hazards associated with the use of its products. However, no manual can address every possible risk. The end-user ultimately is responsible for exercising sound judgment at all times. If this product is used improperly or carelessly, the operator and/or bystanders might sustain serious personal injuries or could even be killed. ALWAYS use the product properly: Failure to read and understand the entire manual before assembling, using or servicing the product constitutes misuse. DO NOT exceed the rated load of the ladder. The total weight applied to the ladder (weight of the user plus tools, etc.) must be less than the rated load. DO NOT climb the ladder UNLESS the front casters retract out of contact with the ground when weight is applied to the bottom step. DO NOT use the ladder on uneven, inclined, or unstable surfaces. The surface must be able to support the ladder and a full capacity load. ONLY use the ladder on level, even surfaces. Make sure that you will not contact overhead objects with your body or with the ladder during use or while moving the ladder. Always unload the ladder before leaving it unattended. Remove foreign matter, like mud or grease, from your shoes before stepping onto the ladder. ALWAYS use the handrails while ascending and descending the ladder. DO NOT attempt to increase the height of the platform or of any individual step by standing on objects placed on the ladder. Inspect the ladder as described in Inspections & Maintenance on p. 6. DO NOT use the ladder if it is not in normal condition. Immediately tag out the ladder and replace each part that fails to pass inspection. DO NOT use the product until it is fully restored to normal condition. ONLY use manufacturer-approved replacement parts. DO NOT use the ladder if any unusual noise or movement is observed while weight is applied to it. Remove the unit from service. DO NOT use the ladder again until it is restored to normal operating condition. DO NOT lean or reach over the sides of the ladder. Reposition the ladder if you cannot safely reach the object you want. DO NOT remove or obscure any label (see Labeling diagram on p. 7). All labels must be readable and undamaged. DO NOT modify this ladder! Unauthorized modifications automatically void the limited warranty (see p. 8) and might make the ladder unsafe to use. This product must be properly maintained to function properly. Keep the ladder clean & dry. Periodically check the integrity of the ladder frame. The ladder should be solid and square and free of rust and corrosion. Copyright 07 Vestil Manufacturing Co. Page of 8

3 Rev. 3/3/07 LAD (6- STEPS), MANUAL Specifications: Dimensions, capacity, and net weight information for each LAD model appears in the diagrams and table below. B A D E F 0 riser height 58 climb angle 0 wheel C 3 front casters G H Model no. LAD-6-4-G LAD-6-4-P LAD-6--G LAD-6--P LAD-7-4-G LAD-7-4-P LAD-7--G LAD-7--P LAD-8-4-G LAD-8-4-P LAD-8--G LAD-8--P LAD-9-4-G LAD-9-4-P LAD-9--G LAD-9--P LAD-0-4-G LAD-0-4-P LAD-0--G LAD-0--P LAD--4-G LAD--4-P LAD---G LAD---P LAD--4-G LAD--4-P LAD---G LAD---P # of steps A: Overall height B: Usable width C: Overall width D: Platform depth E: Step depth F: Platform height G: Usable length H: Overall length / 6 34 / / / / 6 34 / / / 6 34 / / 60 / / 6 34 / / 66 5 / / 6 34 / / / / 6 34 / / / / 6 34 / / 6 7 / / 6 34 / / / / 6 34 / / / / 6 34 / / / / 6 34 / / 85 / / 6 34 / / 9 / / 6 34 / / / / 6 34 / / 4 97 / Net weight 57.0 lb lb. 68. lb lb lb kg 87. lb. 85. kg 9. lb lb lb lb lb lb. 9.5 lb. 6.9 lb. 7.3 lb. 4.6 lb lb lb. 9.4 lb lb lb lb lb lb lb. 3.3 lb. Capacity 59 kg 59 kg 59 kg 59 kg 59 kg 59 kg 59 kg 59 kg 59 kg 59 kg 59 kg 59 kg 59 kg 59 kg Copyright 07 Vestil Manufacturing Co. Page 3 of 8

4 Rev. 3/3/07 LAD (6- STEPS), MANUAL FIG. : Foot Lock Mechanism Exploded Parts Diagram and Bill of Materials Part no. Description Quantity / 6 in. 8 x in. HHCS # zinc-plated bolt / 8 in. 6 zinc-plated hex nut 05 3 / 8 in. 6 x in. hex head bolt / 8 in. shoulder x 3 / 4 in. x 5 / 6 in / 6 in. 8 x in. HHCS # zinc-plated bolt Weldment, frame, caster pivot foot lock / 8 in. Nylock insert nut Roller guide Spring / 8 in. I.D. 0 gauge machine bushing / 6 in. x in. zinc-plated cotter pin / 6 in. USS zinc-plated flat washer Copyright 07 Vestil Manufacturing Co. Page 4 of 8

5 Rev. 3/3/07 LAD (6- STEPS), MANUAL FIG. : LAD-6-4-P, LAD-6-4-G, LAD-6--P, & LAD-6--G exploded parts diagram and bill of materials See FIG. on p. 4 Item no. Part no. Description Quantity Weldment, 6-step frame: LAD-6-4-G LAD-6-4-P LAD-6--G LAD-6--P Weldment, handrail, 6-step ladder: LAD-6-4-G & LAD-6-4-P LAD-6--G & LAD-6--P Weldment, frame, back platform Weldment, back leg, 6-step Frame, base support: LAD-6-4-G & LAD-6-4-P LAD-6--G & LAD-6--P ** Weldment, frame, caster pivot foot lock x, 60 duro. square cap plastic plug ** Spring Wheel axle x / wheel with 6mm steel hub Caster, front ** Roller guide / 6 8 x / zinc-plated # bolt / 6 8 zinc-plated # Nylon lock nut / 8 6 UNC x 3 / 8 zinc-plated hex cap screw / 8 zinc-plated USS flat washer 8 ** / 6 8 x HHCS # zinc-plated bolt 4 ** / 8 I.D. 0 gauge machine bushing ** / 6 x zinc-plated cotter pin ** 05 3 / 8 6 x in. hex head bolt ** / 8 6 zinc-plated hex nut ** / 8 shoulder x 3 / 4 x 5 / 6 8 bolt ** / 8 Nylock insert nut / 6 x / zinc-plated cotter pin / 6 8 x 3 / 4 HHCS # zinc-plated bolt ** / 6 USS zinc-plated USS flat washer ** / 6 8 x HHCS # zinc-plated bolt **Items shown in FIG. on p. 4. Copyright 07 Vestil Manufacturing Co. Page 5 of 8

6 Rev. 3/3/07 LAD (6- STEPS), MANUAL FIG. 3: LAD-7-4-G, LAD-7-4-P, LAD-7--G & LAD-7--P exploded parts diagram and bill of materials Item no. Part no. Description Quantity Weldment, 7-step frame: LAD-7-4-G LAD-7-4-P LAD-7--G LAD-7--P Weldment, handrail, 7-step ladder: LAD-7-4-G & LAD-7-4-P LAD-7--G & LAD-7--P Weldment, frame, back platform Weldment, back leg, 7-step Frame, base support: LAD-7-4-G & LAD-7-4-P LAD-7--G & LAD-7--P ** Weldment, frame, caster pivot foot lock x, 60 duro. square cap plastic plug ** Spring Wheel axle x / wheel with 6mm steel hub Caster, front ** Roller guide / 6 8 x / zinc-plated # bolt / 6 8 zinc-plated # Nylon lock nut / 8 6 UNC x 3 / 8 zinc-plated hex cap screw / 8 zinc-plated USS flat washer / 6 8 x HHCS # zinc-plated bolt 4 ** / 8 I.D. 0 gauge machine bushing ** / 6 x zinc-plated cotter pin ** 05 3 / 8 6 x in. hex head bolt / 8 6 zinc-plated hex nut / 8 shoulder x 3 / 4 x 5 / 6 8 bolt ** / 8 Nylock insert nut / 6 x / zinc-plated cotter pin / 6 8 x 3 / 4 HHCS # zinc-plated bolt ** / 6 USS zinc-plated USS flat washer ** / 6 8 x HHCS # zinc-plated bolt **Items shown in FIG. on p. 4. See FIG. on p. 4 Copyright 07 Vestil Manufacturing Co. Page 6 of 8

7 Rev. 3/3/07 LAD (6- STEPS), MANUAL FIG. 4: LAD-8-4-G, LAD-8-4-P, LAD-8--G, & LAD-8--P exploded parts diagram and bill of materials See FIG. on p. 4 Item no. Part no. Description Quantity Weldment, 8-step frame: LAD-8-4-G LAD-8-4-P LAD-8--G LAD-8--P Weldment, handrail, 8-step ladder: LAD-8-4-G & LAD-8-4-P LAD-8--G & LAD-8--P Weldment, frame, back platform Weldment, back leg, 8-step Frame, base support: LAD-8-4-G & LAD-8-4-P LAD-8--G & LAD-8--P ** Weldment, frame, caster pivot foot lock x, 60 duro. square cap plastic plug ** Spring Wheel axle x / wheel with 6mm steel hub Caster, front ** Roller guide / 6 8 x / zinc-plated # bolt / 6 8 zinc-plated # Nylon lock nut / 8 6 UNC x 3 / 8 zinc-plated hex cap screw / 8 zinc-plated USS flat washer / 6 8 x HHCS # zinc-plated bolt 4 ** / 8 I.D. 0 gauge machine bushing ** / 6 x zinc-plated cotter pin ** 05 3 / 8 6 x in. hex head bolt / 8 6 zinc-plated hex nut / 8 shoulder x 3 / 4 x 5 / 6 8 bolt ** / 8 Nylock insert nut / 6 x / zinc-plated cotter pin / 6 8 x 3 / 4 HHCS # zinc-plated bolt ** / 6 USS zinc-plated USS flat washer ** / 6 8 x HHCS # zinc-plated bolt **Items shown in FIG. on p. 4. Copyright 07 Vestil Manufacturing Co. Page 7 of 8

8 Rev. 3/3/07 LAD (6- STEPS), MANUAL FIG. 5: LAD-9-4-G, LAD-9-4-P, LAD-9--G, & LAD-9--P exploded parts diagram and bill of materials See FIG. on p. 4 Item no. Part no. Description Quantity Weldment, 9-step frame: LAD-9-4-G LAD-9-4-P LAD-9--G LAD-9--P Weldment, handrail, 9-step ladder: LAD-9-4-G & LAD-9-4-P LAD-9--G & LAD-9--P Weldment, frame, back platform Weldment, back leg, 9-step Frame, base support: LAD-9-4-G & LAD-9-4-P LAD-9--G & LAD-9--P ** Weldment, frame, caster pivot foot lock x, 60 duro. square cap plastic plug ** Spring Wheel axle x / wheel with 6mm steel hub Caster, front ** Roller guide / 6 8 x / zinc-plated # bolt / 6 8 zinc-plated # Nylon lock nut / 8 6 UNC x 3 / 8 zinc-plated hex cap screw / 8 zinc-plated USS flat washer / 6 8 x HHCS # zinc-plated bolt 4 ** / 8 I.D. 0 gauge machine bushing ** / 6 x zinc-plated cotter pin ** 05 3 / 8 6 x in. hex head bolt / 8 6 zinc-plated hex nut / 8 shoulder x 3 / 4 x 5 / 6 8 bolt ** / 8 Nylock insert nut / 6 x / zinc-plated cotter pin / 6 8 x 3 / 4 HHCS # zinc-plated bolt ** / 6 USS zinc-plated USS flat washer ** / 6 8 x HHCS # zinc-plated bolt **Items shown in FIG. on p. 4. Copyright 07 Vestil Manufacturing Co. Page 8 of 8

9 Rev. 3/3/07 LAD (6- STEPS), MANUAL FIG. 6: LAD-0-4-G, LAD-0-4-P, LAD-0--G, & LAD-0--P exploded parts diagram and bill of materials See FIG. on p. 4 Item no. Part no. Description Quantity Weldment, 0-step frame: LAD-0-4-G LAD-0-4-P LAD-0--G LAD-0--P Weldment, handrail, 0-step ladder: LAD-0-4-G & LAD-0-4-P LAD-0--G & LAD-0--P Weldment, frame, back platform Weldment, back leg, 0-step Frame, base support: LAD-0-4-G & LAD-0-4-P LAD-0--G & LAD-0--P ** Weldment, frame, caster pivot foot lock x, 60 duro. square cap plastic plug ** Spring Wheel axle x / wheel with 6mm steel hub Caster, front ** Roller guide / 6 8 x / zinc-plated # bolt / 6 8 zinc-plated # Nylon lock nut / 8 6 UNC x 3 / 8 zinc-plated hex cap screw / 8 zinc-plated USS flat washer / 6 8 x HHCS # zinc-plated bolt 4 ** / 8 I.D. 0 gauge machine bushing ** / 6 x zinc-plated cotter pin ** 05 3 / 8 6 x in. hex head bolt / 8 6 zinc-plated hex nut / 8 shoulder x 3 / 4 x 5 / 6 8 bolt ** / 8 Nylock insert nut / 6 x / zinc-plated cotter pin / 6 8 x 3 / 4 HHCS # zinc-plated bolt ** / 6 USS zinc-plated USS flat washer ** / 6 8 x HHCS # zinc-plated bolt **Items shown in FIG. on p. 4. Copyright 07 Vestil Manufacturing Co. Page 9 of 8

10 Rev. 3/3/07 LAD (6- STEPS), MANUAL FIG. 7: LAD--4-G, LAD--4-P, LAD---G, & LAD---P exploded parts diagram and bill of materials Item no. Part no. Description Quantity Weldment, step 58, warehouse, upper: LAD--4-G LAD--4-P LAD---G LAD---P Weldment, -step, frame, lower: LAD--4-G LAD--4-P & LAD---G & LAD---P Assembly, outrigger, right ** Assembly, outrigger, left Weldment, frame, back platform Weldment, back leg, -step Weldment, frame, caster pivot foot lock Weldment, handrail, 58 climb, 8-step: LAD--4-G & LAD--4-P LAD---G & LAD---P Weldment, handrail, -step warehouse Assembly, specialty hardware, handrail splice Hinge plates, connector Frame, base support: LAD--4-G & LAD--4-P LAD---G & LAD---P Toeguard, removable back plate, formed Wheel axle / 4 snap hook x / wheel, 6mm steel hub Caster ** Roller guide 4 ** Spring x, 60 duro., square cap plastic plug, black Grip, square tube sleeve / 6 chain, 4 long / 6 8 x 3 / 4 HHCS # zinc-plated bolt / 6 8 UNC x / 4 HHCS # zinc-plated bolt / 6 8 UNC x 3 / 4 HHCS # zinc-plated bolt / 6 8 UNC x / 4 HHCS # zinc-plated bolt / 8 6 x in. hex head bolt ** / 8 shoulder x 3 / 4 x 5 / 6 8 bolt / 6 USS zinc-plated USS flat washer 0 ** / zinc-plated USS flat washer 8 6 ** / 8 I.D. 0 gauge machine bushing See FIG. on p / 8 6 zinc-plated hex nut / 6 8 zinc-plated # Nylon lock nut 46 ** / 8 Nylock insert nut / 6 x / zinc-plated cotter pin ** / 6 x zinc-plated cotter pin **Items shown in FIG. on p. 4. Copyright 07 Vestil Manufacturing Co. Page 0 of 8

11 Rev. 3/3/07 LAD (6- STEPS), MANUAL FIG. 8: LAD--4-G, LAD--4-P, LAD---G, & LAD---P exploded parts diagram and bill of materials See FIG. on p. 4 Item no. Part no. Description Quantity Weldment, step 58, warehouse, upper: LAD--4-G LAD--4-P LAD---G LAD---P Weldment, -step, frame, lower: LAD--4-G LAD--4-P & LAD---G & LAD---P Assembly, outrigger, right ** Assembly, outrigger, left Weldment, frame, back platform Weldment, back leg, -step Weldment, frame, caster pivot foot lock Weldment, handrail, 58 climb, 8-step: LAD--4-G & LAD--4-P LAD---G & LAD---P Weldment, handrail, -step warehouse Assembly, specialty hardware, handrail splice Hinge plates, connector Frame, base support: LAD--4-G & LAD--4-P LAD---G & LAD---P Toeguard, removable back plate, formed Wheel axle / 4 snap hook x / wheel, 6mm steel hub Caster ** Roller guide 4 ** Spring x, 60 duro., square cap plastic plug, black Grip, square tube sleeve / 6 chain, 4 long / 6 8 x 3 / 4 HHCS # zinc-plated bolt / 6 8 UNC x / 4 HHCS # zinc-plated bolt / 6 8 UNC x 3 / 4 HHCS # zinc-plated bolt / 6 8 UNC x / 4 HHCS # zinc-plated bolt / 8 6 x in. hex head bolt ** / 8 shoulder x 3 / 4 x 5 / 6 8 bolt / 6 USS zinc-plated USS flat washer 0 ** / 8 zinc-plated USS flat washer 6 ** / 8 I.D. 0 gauge machine bushing / 8 6 zinc-plated hex nut / 6 8 zinc-plated # Nylon lock nut 50 ** / 8 Nylock insert nut / 6 x / zinc-plated cotter pin ** / 6 x zinc-plated cotter pin **Items shown in FIG. on p. 4. Copyright 07 Vestil Manufacturing Co. Page of 8

12 Rev. 3/3/07 LAD (6- STEPS), MANUAL Assembly instructions: Numbers in parentheses correspond to item numbers in the exploded parts diagrams on pp. 4-. Step [ and -step models only]: Attach the upper () and lower () stair weldments using hinge plates () using 5 / 6 8 hardware as shown in the illustration below. Install bolts through the bolt holes in the hinge plates and the hinge brackets highlighted with arrows. Hinge bracket a e f g h d b c Hinge plate () f e g h Lower step weldment () Hinge bracket Upper step weldment () d a b c 5 / 6 8 lock nut 5 / 6 8 x 3 / 4 bolt Copyright 07 Vestil Manufacturing Co. Page of 8

13 Rev. 3/3/07 LAD (6- STEPS), MANUAL Step : Fasten the back leg weldment to the stair frame weldment with 5 / 6 in. hardware. Be sure to orient the back leg weldment as shown below. Back leg weldment + Stair frame weldment Base bracket Axle receiver 5 / 6 in.-8 lock nut 5 / 6 in.-8 x / in. bolt Step 3: Fasten the base supports to the assembly with 5 / 6 in. 8 hardware as shown below. + Ladder assembly Base support 3 / 8 in. 6 x in. bolt 3 / 8 in. 6 lock nut 5 / 6 in. 8 lock nut 5 / 6 in. 8 x / 4 in. bolt Copyright 07 Vestil Manufacturing Co. Page 3 of 8

14 Rev. 3/3/07 LAD (6- STEPS), MANUAL Step 4: Install the plugs, caps, axle and wheels. a) Install the plastic plugs and square caps in the front legs. First, press the in. plastic plugs into the front legs. Then, press the square caps over the plugs and onto the ends of the legs. If necessary, use a rubber mallet to gently tap the plugs and caps into place. b) Insert the axle through the axle receiver of the back leg weldment. c) Then, slide the wheels onto the ends of the axle. Secure the wheels to the axle by inserting a cotter pin through the pinhole in each end of the axle. Periodically lubricate the axle to allow the wheels to rotate freely. Axle Ladder assembly Wheel Cotter pin Cotter pin Axle receiver Axle Cotter pin in. black plastic plug in. x in. square cap Wheel Axle Step 5: Install the outriggers as diagrammed ( and step models only). Left side outrigger Right side outrigger 5 / 6 8 x 3 / 4 bolt 5 / 6 in. lock nut Outrigger (right) Outriggers installed Copyright 07 Vestil Manufacturing Co. Page 4 of 8

15 Rev. 3/3/07 LAD (6- STEPS), MANUAL Step 6: Install the toeboard ( & -step models only). 5 / 6 flat washer Toeboard ( ) 5 / 6 8 lock nut 5 / 6 flat washer 5 / 6 8 x / 4 bolt Step 7A: (0; & step models) fasten the upper and lower portions of the handrails to the ladder assembly. Upper handrail Cross bar 5 / 6 flat washer and lock washer Cross bar Attach snap hooks to the hook rings on the handrails tube sleeve (black). Slide onto ends of upper handrails 5 / 6 8 x / bolt 5 / 6 8 UNC x 3 / 4 and 5 / 6 8 lock nut Snap hook Hook ring Lower handrail Splice To connect the upper and lower handrails, first slide a tube sleeve () onto the end of each upper handrail (8). Next, A) press the splice (0) into the interior space of the handrails; and B) tighten the connection by turning the hub clockwise. Then, slide the tube sleeves over the splices. A. Insert into upper handrail B. Set screw 5 / 6 8 UNC x 3 / 4 and 5 / 6 8 lock nut Insert into lower handrail Set screw Copyright 07 Vestil Manufacturing Co. Page 5 of 8

16 Rev. 3/3/07 LAD (6- STEPS), MANUAL Step 7B: Install the handrails, handrail cross bar, and safety chain. Cross bar 5 / 6 in. flat washer 5 / 6 8 x / bolt 5 / 6 in. lock washer 5 / 6 in. 8 lock nut 5 / 6 in. 8 x / in. bolt Brake release bracket Using the ladder: Before climbing the ladder, press on the bottom step and confirm that the front casters automatically rotate upward and out of contact with the ground. This safety feature ensures that the ladder is supported in front by the square caps on the bottoms of the front legs rather than by the front casters. The caps prevent the front end of the ladder from sliding. If the casters do not automatically retract, do not use the ladder until it is restored to normal operating condition. To move the ladder, bring the front casters back into contact with the ground. To do this, press on the brake release brackets while lifting the ladder by the handrails. Inspections & Maintenance: Regular inspections and maintenance are necessary to keep the ladder in normal working condition. Initial inspection before using a new ladder for the first time, inspect it to confirm normal condition. After the first us, inspect the following features at least once per month: Front casters/bottom step mechanism: inspect daily for cracks and damage. The casters should retract automatically whenever weight is applied to the bottom step. They should not wobble while spinning but should roll smoothly and easily. Examine the caster stems and retaining hardware. Springs should be undamaged and should forcefully recoil. Rear wheels, axle, & hardware: Make sure that each wheel is undamaged and rotates smoothly and evenly. Examine the axle and the axle receiver (see step 4, p. 4) of the back leg weldment. They should not be bent or cracked. Confirm that all retaining hardware is securely fastened. All frame pieces (step weldment, back leg weldment, brace supports) and all fasteners (bolts, nuts, pins): Inspect weekly for damage such as excessive wear, warps, and cracks. Replace all parts that are damaged before using the ladder again. All frame pieces should be square, rigid and free of rust and corrosion. Remove rust with steel wool or a metal bristle brush and apply touch-up paint. Handrails: Examine the handrails. Confirm that each handrail is solidly fastened to the step weldment(s). Check all fasteners and tighten any connection that is loose. Rubber caps (on front legs; see step 4 on p. 4): check the caps for cracks and/or excessive or uneven wear. If either cap is significantly worn or damaged, replace it before returning the ladder to service. Maintenance: in addition to correcting issues discovered during inspections, maintain the ladder by Cleaning the ladder to remove dirt and grime, especially from step surfaces. Applying touchup paint wherever the finish is damaged. Copyright 07 Vestil Manufacturing Co. Page 6 of 8

17 Rev. 3/3/07 LAD (6- STEPS), MANUAL Labeling diagram: Each ladder should be labeled as shown below. Replace any label that is damaged or missing. A A B E C D C B F E D F Ladders with gate option A: Label 8 B: Label 87 C: Label 740 D: Label 79 E: Label 468 F: Label 998 Copyright 07 Vestil Manufacturing Co. Page 7 of 8

18 Rev. 3/3/07 LAD (6- STEPS), MANUAL LIMITED WARRANTY Vestil Manufacturing Corporation ( Vestil ) warrants this product to be free of defects in material and workmanship during the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is covered by the warranty, after we receive a proper request from the warrantee (you) for warranty service. Who may request service? Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an authorized distributor AND Vestil has been fully paid. What is an original part? An original part is a part used to make the product as shipped to the warrantee. What is a proper request? A request for warranty service is proper if Vestil receives: ) a photocopy of the Customer Invoice that displays the shipping date; AND ) a written request for warranty service including your name and phone number. Send requests by any of the following methods: Mail Fax Vestil Manufacturing Corporation (60) sales@vestil.com 999 North Wayne Street, PO Box 507 Phone Angola, IN (60) In the written request, list the parts believed to be defective and include the address where replacements should be delivered. What is covered under the warranty? After Vestil receives your request for warranty service, an authorized representative will contact you to determine whether your claim is covered by the warranty. Before providing warranty service, Vestil may require you to send the entire product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the following original dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders. It also covers defects in original parts that wear under normal usage conditions ( wearing parts ), such as bearings, hoses, wheels, seals, brushes, and batteries. How long is the warranty period? The warranty period for original dynamic components is 90 days. For wearing parts, the warranty period is 90 days. The warranty periods begin on the date when Vestil ships the product to the warrantee. If the product was purchased from an authorized distributor, the periods begin when the distributor ships the product. Vestil may, at its sole discretion, extend the warranty periods for products shipped from authorized distributors by up to 30 days to account for shipping time. If a defective part is covered by the warranty, what will Vestil do to correct the problem? Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact you to discuss your claim. What is not covered by the warranty?. Labor;. Freight; 3. Occurrence of any of the following, which automatically voids the warranty: Product misuse; Negligent operation or repair; Corrosion or use in corrosive conditions; Inadequate or improper maintenance; Damage sustained during shipping; Accidents involving the product; Unauthorized modifications: DO NOT modify the product IN ANY WAY without first receiving written authorization from Vestil. Modification(s) might make the product unsafe to use or might cause excessive and/or abnormal wear. Do any other warranties apply to the product? Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty. Copyright 07 Vestil Manufacturing Co. Page 8 of 8

LAD-EZ Series Portable Warehouse Ladders, 6-12 Steps Assembly Manual

LAD-EZ Series Portable Warehouse Ladders, 6-12 Steps Assembly Manual Rev. 3/3/07 LAD-EZ (6- STEPS), MANUAL Vestil Manufacturing Corp. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-339 www.vestilmfg.com

More information

LAD-MM Series Mobile Ladder Stands Instruction Manual

LAD-MM Series Mobile Ladder Stands Instruction Manual Rev..8.07 LAD-MM, MANUAL Vestil Manufacturing Corp. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-339 Web: www.vestilmfg.com

More information

RLAD-series Portable 2-Step Ladders Instruction Manual

RLAD-series Portable 2-Step Ladders Instruction Manual VESTIL MANUFACTURING CORP. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-1339 www.vestilmfg.com e-mail: HUsales@vestil.comU

More information

LAD-RF Series Collapsible Mobile Ladder Stands Instruction Manual

LAD-RF Series Collapsible Mobile Ladder Stands Instruction Manual Rev..4.05 LAD-RF, MANUAL.doc Vestil Manufacturing Corp. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-339 Url: www.vestilmfg.com

More information

COLV-6 SERIES VERTICAL CROSSOVER LADDERS INSTRUCTION MANUAL

COLV-6 SERIES VERTICAL CROSSOVER LADDERS INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

CANT-Series Cantilever Carts Instruction Manual

CANT-Series Cantilever Carts Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: HUinfo@vestil.comU CANT-Series

More information

RDC 100 & RDC DRUM ROTATING CARTS ASSEMBLY INSTRUCTIONS

RDC 100 & RDC DRUM ROTATING CARTS ASSEMBLY INSTRUCTIONS Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665 7586 or Toll Free (800) 348 0868 Fax: (260) 665 1339 www.vestilmfg.com e mail: info@vestil.com RDC

More information

CYL-EH, CYL-EH-FF, CYL-EH-FP, & CYL-EH-FP-FF Cylinder Dollies Instruction Manual

CYL-EH, CYL-EH-FF, CYL-EH-FP, & CYL-EH-FP-FF Cylinder Dollies Instruction Manual Vestil Manufacturing Co. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com CYL-EH,

More information

MCHT-350 MAGNETIC CYLINDER HAND TRUCK INSTRUCTION MANUAL

MCHT-350 MAGNETIC CYLINDER HAND TRUCK INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

CJ-BEAM Trailer Stabilizing Jacks Instruction Manual

CJ-BEAM Trailer Stabilizing Jacks Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

CYL-EX-12-S, CYL-EX-12-E, CYL-EX-18-S & CYL-EX-18-E Series Cylinder Storage Cabinets Assembly and Maintenance Manual

CYL-EX-12-S, CYL-EX-12-E, CYL-EX-18-S & CYL-EX-18-E Series Cylinder Storage Cabinets Assembly and Maintenance Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

TT Series Benchtop Turntables Instruction Manual

TT Series Benchtop Turntables Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 6703 Telephone: (260) 665-7586 -or- Toll Free (800) 38-0868 Fax: (260) 665-1339 URL: www.vestilmfg.com Email: info@vestil.com

More information

08/2010 Rev. 2/7/2018 DGS-A, MANUAL. DGS-A, DGD-A, & DGS-AG Fork-Mounted Drum Lifters Use and Maintenance Manual DGS-AG

08/2010 Rev. 2/7/2018 DGS-A, MANUAL. DGS-A, DGD-A, & DGS-AG Fork-Mounted Drum Lifters Use and Maintenance Manual DGS-AG Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com Email: info@vestil.com DGS-A,

More information

CRP-series Carpet Rams Instruction Manual

CRP-series Carpet Rams Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: info@vestil.com

More information

LSC 3052 PCW LANDSCAPE CART ASSEMBLY INSTRUCTIONS

LSC 3052 PCW LANDSCAPE CART ASSEMBLY INSTRUCTIONS VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665 7586 or Toll Free (800) 348 0868 Fax: (260) 665 339 www.vestilmfg.com e mail: sales@vestil.com LSC

More information

rev. 2/24/2017 ALUMINUM SHEET DECK PLATFORM TRUCK ASD

rev. 2/24/2017 ALUMINUM SHEET DECK PLATFORM TRUCK ASD VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

SBRL-SERIES SPREADER BEAMS INSTRUCTION MANUAL

SBRL-SERIES SPREADER BEAMS INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: info@vestil.com

More information

LSC SD LANDSCAPE CART ASSEMBLY I NSTRUCTIONS

LSC SD LANDSCAPE CART ASSEMBLY I NSTRUCTIONS VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665 7586 or Toll Free (800) 348 0868 Fax: (260) 665 1339 www.vestilmfg.com e mail: sales@vestil.com LSC

More information

HOP-LP Portable Steel Dumping Hoppers Instruction Manual

HOP-LP Portable Steel Dumping Hoppers Instruction Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

CRF-SERIES CARPET POLES INSTRUCTION MANUAL

CRF-SERIES CARPET POLES INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

HOOK-BASE INSTRUCTION MANUAL

HOOK-BASE INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 www.vestilmfg.com e-mail: sales@vestil.com

More information

CART-800-D-TS INSTRUCTION MANUAL

CART-800-D-TS INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

08/2010 Rev. 4/28/2017 FMDL, MANUAL. FMDL-Series Single & Double Eagle Beak Fork-Mounted Drum Lifters Use and Maintenance Manual

08/2010 Rev. 4/28/2017 FMDL, MANUAL. FMDL-Series Single & Double Eagle Beak Fork-Mounted Drum Lifters Use and Maintenance Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com Email: info@vestil.com FMDL-Series

More information

P-HOP-Series Portable Steel Hoppers Instruction Manual

P-HOP-Series Portable Steel Hoppers Instruction Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

Rev. 12/16/2015 WTJ-HITCH, MANUAL. WTJ-HITCH Series Hitch-Mounted Jib Cranes Use and Maintenance Manual

Rev. 12/16/2015 WTJ-HITCH, MANUAL. WTJ-HITCH Series Hitch-Mounted Jib Cranes Use and Maintenance Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

Instruction Manual DJG-100 and DJG

Instruction Manual DJG-100 and DJG Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: info@vestil.com

More information

ABLT-H SERIES AIR BAG LIFT TABLES INSTRUCTION MANUAL

ABLT-H SERIES AIR BAG LIFT TABLES INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com ABLT-H

More information

Rev. 10/27/2015 CDL-2000, MANUAL

Rev. 10/27/2015 CDL-2000, MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com CDL-2000

More information

FE-Series Fork Extensions Instruction Manual

FE-Series Fork Extensions Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: info@vestil.com

More information

VAN-J Series Vehicle Mounted Jib Cranes Instruction Manual

VAN-J Series Vehicle Mounted Jib Cranes Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 4670 Telephone: (260) 665-7586 -or- Toll Free (800) 48-0868 Fax: (260) 665-19 Web: www.vestilmfg.com e-mail: HUinfo@vestil.comU

More information

WP-400 Series Electric Work Platforms Instruction Manual

WP-400 Series Electric Work Platforms Instruction Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

PEL-88-A-SWA & PEL-100-A-SWA Wrapping Machines Use and Maintenance Manual

PEL-88-A-SWA & PEL-100-A-SWA Wrapping Machines Use and Maintenance Manual VESTIL MANUFACTURING CORP. 999 North Wayne Street, P.O. Box 507, Angola, IN 6703 Telephone: (60) 665-7586 -or- Toll Free (800) 38-0868 Fax: (60) 665-339 www.vestilmfg.com e-mail: sales@vestil.com PEL-88-A-SWA

More information

P-JIB Portable Jib Crane Instruction Manual

P-JIB Portable Jib Crane Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: info@vestil.com

More information

CART-FP Scissor Carts with 2-Speed Auto-Shifting Foot Pump Instruction Manual

CART-FP Scissor Carts with 2-Speed Auto-Shifting Foot Pump Instruction Manual Rev. 4/18/2018 CART-FP, MANUAL Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com

More information

H-SERIES HOPPERS Instruction Manual

H-SERIES HOPPERS Instruction Manual Rev. /2/208 H, MANUAL.doc VESTIL MANUFACTURING CORP. 2 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-33 www.vestilmfg.com e-mail:

More information

LP-6 LPG Cylinder Truck Use & Maintenance Manual

LP-6 LPG Cylinder Truck Use & Maintenance Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com LP-6 LPG Cylinder Truck

More information

H-SERIES HOPPERS Instruction Manual

H-SERIES HOPPERS Instruction Manual Rev. 7/20/208 H-hoppers MANUAL Vestil Manufacturing Corp. 2 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-33 Web: www.vestilmfg.com

More information

JIB-FM Series Floor Mounted Jib Cranes Instruction Manual

JIB-FM Series Floor Mounted Jib Cranes Instruction Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: HUsales@vestil.comU

More information

OROAD-400 Traction Drive Electric Cart Use & Maintenance Manual

OROAD-400 Traction Drive Electric Cart Use & Maintenance Manual Rev. 8/8/2017 OROAD-400, MANUAL.doc VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com

More information

D-SERIES HOPPERS Instruction Manual

D-SERIES HOPPERS Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 Website: www.vestilmfg.com e-mail: info@vestil.com

More information

A-LIFT Manual Winch Lift Trucks Instruction Manual

A-LIFT Manual Winch Lift Trucks Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: HUsales@vestil.comU

More information

Table of Contents Rev. 10/31/2018 FHA MANUAL. FHA-series Fixed Height Aluminum Gantry Crane Instruction Manual

Table of Contents Rev. 10/31/2018 FHA MANUAL. FHA-series Fixed Height Aluminum Gantry Crane Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 Web: www.vestilmfg.com e-mail: info@vestil.com

More information

PEL-Series Pallet Handlers Instruction Manual

PEL-Series Pallet Handlers Instruction Manual Rev. 8/3/207 Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 www.vestilmfg.com e-mail: sales@vestil.com

More information

Instruction Manual. Forklift-Karrier

Instruction Manual. Forklift-Karrier Instruction Manual Forklift-Karrier Note: The Owner/Operator must read carefully and understand all the information presented in this manual before using this device. - 0 - Contents 1. Figure and Parameter

More information

FHS-Series Steel Fixed Height Gantry Cranes Instruction Manual

FHS-Series Steel Fixed Height Gantry Cranes Instruction Manual 24 rev. /5/205 FHS, MANUAL.doc Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 Url: www.vestilmfg.com

More information

INSTRUCTION MANUAL MODELS COVERED: CART-300-S-HR, FOR PREMIUM SCISSOR LIFT CARTS CART-600-S-HR,, CART-1000-S-HR, CART-400-D-HR - 1 -

INSTRUCTION MANUAL MODELS COVERED: CART-300-S-HR, FOR PREMIUM SCISSOR LIFT CARTS CART-600-S-HR,, CART-1000-S-HR, CART-400-D-HR - 1 - INSTRUCTION MANUAL FOR PREMIUM SCISSOR LIFT CARTS MODELS COVERED: CART-300-S-HR, CART-600-S-HR,, CART-1000-S-HR, CART-400-D-HR - 1 - Content 1. Warning.3 2. Caution..4 3. Name of parts...5 4. Daily inspection

More information

LPC-SERIES POSITIVE LOCKING PLATE CLAMPS USE AND MAINTENANCE MANUAL

LPC-SERIES POSITIVE LOCKING PLATE CLAMPS USE AND MAINTENANCE MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

LM-Series and LMS-Series Fork Truck Attachments Use and Maintenance Manual

LM-Series and LMS-Series Fork Truck Attachments Use and Maintenance Manual 0/ rev. 7/29/204 LM-boom, manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 www.vestilmfg.com

More information

Rev. 6/16/2015 EMC, MANUAL.doc. EMC-Series Tilting Tables Use and Maintenance Manual

Rev. 6/16/2015 EMC, MANUAL.doc. EMC-Series Tilting Tables Use and Maintenance Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

VESTIL MANUFACTURING CORP. OPERATION & SERVICE MANUAL PORTABLE DRUM JACK (DRUM-55-S) 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703

VESTIL MANUFACTURING CORP. OPERATION & SERVICE MANUAL PORTABLE DRUM JACK (DRUM-55-S) 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 OPERATION & SERVICE MANUAL PORTABLE DRUM JACK (DRUM-55-S) VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868 FAX:

More information

CART-DC Scissor Carts with Battery-Powered Tabletop Operation and Maintenance Manual

CART-DC Scissor Carts with Battery-Powered Tabletop Operation and Maintenance Manual Rev. 4/18/2018 CART-DC, MANUAL Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com

More information

SCTAB-500, SCTAB-750D, SCTAB-1000 & SCTAB-2000 SCISSOR LIFT TABLES USE AND MAINTENANCE MANUAL

SCTAB-500, SCTAB-750D, SCTAB-1000 & SCTAB-2000 SCISSOR LIFT TABLES USE AND MAINTENANCE MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

HDC-905 Series Hydraulic Drum Crushers Instruction Manual

HDC-905 Series Hydraulic Drum Crushers Instruction Manual HDC-905 Series Hydraulic Drum Crushers Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax:

More information

OWNER'S MANUAL HYDRAULIC DRUM CRUSHER/COMPACTOR MODELS HDC-900 & HDC-905

OWNER'S MANUAL HYDRAULIC DRUM CRUSHER/COMPACTOR MODELS HDC-900 & HDC-905 Vestil Manufacturing Corporation 2999 North Wayne Street, P.O. Box 507 Angola, Indiana 46703 USA Distributed by Ergonomic Partners Email: sales@ergonomicpartners.com Web: www.ergonomicpartners.com PH:

More information

STEEL ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL

STEEL ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL AHS manual 1011 rev. 10/6/011 STEEL ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 4670 TELEPHONE: (60) 665-7586 -OR- TOLL

More information

OPERATION & SERVICE MANUAL DRUM (MANUAL DRUM LIFTER)

OPERATION & SERVICE MANUAL DRUM (MANUAL DRUM LIFTER) OPERATION & SERVICE MANUAL DRUM-55-36 (MANUAL DRUM LIFTER) Vestil Manufacturing Corp. 2999 North Wayne St., Angola, IN 46703 Ph: 260-665-7586. Fax: 260-665-1339 E-mail: Sales@vestil.com Website: www.vestil.com

More information

CART-CTD Scissor Carts with Powered Tabletop and Powered Drive Operation and Maintenance Manual

CART-CTD Scissor Carts with Powered Tabletop and Powered Drive Operation and Maintenance Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Web: www.vestilmfg.com e-mail: info@vestil.com

More information

HYDRA SERIES MANUAL HYDRAULIC LIFT TRUCKS ASSEMBLY, USE, AND MAINTENANCE MANUAL

HYDRA SERIES MANUAL HYDRAULIC LIFT TRUCKS ASSEMBLY, USE, AND MAINTENANCE MANUAL VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

FORK EXTENSIONS, SERIES FE INSTRUCTION MANUAL

FORK EXTENSIONS, SERIES FE INSTRUCTION MANUAL FORK EXTENSIONS, SERIES FE INSTRUCTION MANUAL STANDARD FE ROUNDED FE TRIANGULAR FE VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL

More information

CBS-Series Counterbalanced Stackers Instruction Manual

CBS-Series Counterbalanced Stackers Instruction Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

FOR PREMIUM SCISSOR LIFT CARTS MODELS COVERED: CART-300-S-FR, CART-300-D-FR, CART-600-S-FR, CART-600-D-FR, CART-1000-S-FR, CART-1000-D-FR

FOR PREMIUM SCISSOR LIFT CARTS MODELS COVERED: CART-300-S-FR, CART-300-D-FR, CART-600-S-FR, CART-600-D-FR, CART-1000-S-FR, CART-1000-D-FR INSTRUCTION MANUAL FOR PREMIUM SCISSOR LIFT CARTS MODELS COVERED: CART-300-S-FR, CART-300-D-FR, CART-600-S-FR, CART-600-D-FR, CART-1000-S-FR, CART-1000-D-FR Note: Owner/Operator must read and understand

More information

01/11 rev. 3/12/2013 LM-series fork-mountable booms

01/11 rev. 3/12/2013 LM-series fork-mountable booms 0/ rev. /2/20 LM-series fork-mountable booms FORK-MOUNTED LIFT MASTER BOOMS USE AND MAINTENANCE MANUAL LM-OBT & LM-OBNT LM-HRT & LM-HRNT LM-T & LM-NT LM-EBT & LM-EBNT VESTIL MANUFACTURING CORP. 2999 NORTH

More information

ALUMINUM ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL

ALUMINUM ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL AHA manual 1111 rev. 1/5/01 ALUMINUM ADJUSTABLE-HEIGHT GANTRY CRANE INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. 999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 4670 TELEPHONE: (60) 665-7586 -OR- TOLL

More information

4/12/2017 SWA-48, MANUAL. SWA-48 and SWA-48-PMO Instruction Manual

4/12/2017 SWA-48, MANUAL. SWA-48 and SWA-48-PMO Instruction Manual Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 www.vestilmfg.com e-mail: info@vestil.com SWA-48

More information

CB-PMPS Series Counterbalanced Pallet Handlers Instruction Manual

CB-PMPS Series Counterbalanced Pallet Handlers Instruction Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: sales@vestil.com

More information

03/10/03 9/7/2017 HDD, MANUAL

03/10/03 9/7/2017 HDD, MANUAL Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-339 Web: www.vestilmfg.com e-mail: info@vestil.com

More information

E-TUG SERIES ELECTRIC POWERED TUGGER

E-TUG SERIES ELECTRIC POWERED TUGGER E-TUG SERIES ELECTRIC POWERED TUGGER OPERATION AND MAINTENANCE MANUAL E-TUG, Manual VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll

More information

INSTRUCTION MANUAL MOBILE LADDER STAND

INSTRUCTION MANUAL MOBILE LADDER STAND INSTRUCTION MANUAL MOBILE LADDER STAND LAD-RF MODEL NO. SERIAL NO. VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868

More information

03/10/03 10/10/2017 T-HOP, MANUAL

03/10/03 10/10/2017 T-HOP, MANUAL Vestil Manufacturing Corp. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 Website: www.vestilmfg.com Email: info@vestil.com

More information

Before equipment use, please read this operation manual carefully. Serial Number: Date Purchased:

Before equipment use, please read this operation manual carefully. Serial Number: Date Purchased: Pushed & Geared Trolleys OPERATION MANUAL This operation manual is intended as an instruction manual for trained personnel who are in charge of installation, maintenance, repair etc. Before equipment use,

More information

TCD -Series Trash Can Dumpers Instruction Manual

TCD -Series Trash Can Dumpers Instruction Manual Vestil Manufacturing Corp. 999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (60) 665-7586 -or- Toll Free (800) 348-0868 Fax: (60) 665-1339 Web: www.vestilmfg.com Email: info@vestil.com

More information

On-A-Roll Lifter Instruction Manual for Standard Models Read Before Use!

On-A-Roll Lifter Instruction Manual for Standard Models Read Before Use! On-A-Roll Lifter Instruction Manual for Standard Models Read Before Use! Important instructional, safety and precautionary information! It is the user s responsibility to exercise good judgment, common

More information

INSTRUCTION MANUAL VERTICAL PLATE CLAMP MODEL EPC (10, 20, 40, & 80)

INSTRUCTION MANUAL VERTICAL PLATE CLAMP MODEL EPC (10, 20, 40, & 80) INSTRUCTION MANUAL VERTICAL PLATE CLAMP MODEL EPC (10, 20, 40, & 80) MODEL NO. SERIAL NO. VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR-

More information

Heavy Duty Jack Stands

Heavy Duty Jack Stands Heavy Duty Jack Stands Operating Instructions & Parts Manual Made in the U.S.A. Model Number HW93511 Capacity per pair 10 Ton Model Number HW93512 Capacity per pair 10 Ton This is the safety alert symbol.

More information

MANUAL HYDRAULIC LIFT TRUCKS INSTRUCTION MANUAL

MANUAL HYDRAULIC LIFT TRUCKS INSTRUCTION MANUAL MANUAL HYDRAULIC LIFT TRUCKS INSTRUCTION MANUAL HYDRA-2 HYDRA-4 HYDRA-HD MODEL NO. SERIAL NO. VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586

More information

Heavy Duty Engine Cranes

Heavy Duty Engine Cranes Heavy Duty Engine Cranes Operating Instructions & Parts Manual Model Number Atd-7484 Atd-7485 (Foldable Legs) Capacity 2 Ton 2 Ton Model Atd-7484 Model Atd-7485 Atd Tools Inc. 160 Enterprise Drive, Wentzville,

More information

INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. MODELS NUMBER: PM4-xxxx-LP URL:

INSTRUCTION MANUAL VESTIL MANUFACTURING CORP. MODELS NUMBER: PM4-xxxx-LP URL: INSTRUCTION MANUAL FOR Low Profile 4,000 lbs. Pallet Truck MODELS NUMBER: PM4-xxxx-LP VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL

More information

UMS Storage Rack ASSEMBLY INSTRUCTIONS Chief Automotive Systems, Inc.

UMS Storage Rack ASSEMBLY INSTRUCTIONS Chief Automotive Systems, Inc. UMS Storage Rack ASSEMBLY INSTRUCTIONS R 2000 Chief Automotive Systems, Inc. Chief s Limited One-Year Warranty & Liability CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies,

More information

Operator s Manual. Go Galvanized! YOU'RE ALWAYS AHEAD...WITH A MODERN BEHIND.

Operator s Manual. Go Galvanized! YOU'RE ALWAYS AHEAD...WITH A MODERN BEHIND. SUMMER 2008 rock & landscape rake Operator s Manual 003-7445 003-7450 003-7460 003-7440 003-7445 003-7450 YOU'RE ALWAYS AHEAD...WITH A MODERN BEHIND. P.O. Box 790 Beaumont, Tx 77704 409.833.2665 1.800.231.8198

More information

Installation and Parts Manual for SPANCO E Series Gantry Cranes

Installation and Parts Manual for SPANCO E Series Gantry Cranes Manual No. 103-0004 REV. 1/10 Installation and Parts Manual for SPANCO E Series Gantry Cranes ISO 9001 REGISTERED SPANCO, Inc. TABLE OF CONTENTS Warnings... 3 Assembly Instructions... 4 Serial Number Location...

More information

Breezy EC Transport Wheelchair

Breezy EC Transport Wheelchair B r e e z y E C Tr a n s p o r t W h e e l c h a i r Breezy EC Transport Wheelchair O w n e r s M a n u a l READ BEFORE USE REVIEW THIS MANUAL Before using this chair you, and each person who may assist

More information

INSTALLATION INSTRUCTIONS FOR MOUNTING HARDWARE KIT F-105K2.5

INSTALLATION INSTRUCTIONS FOR MOUNTING HARDWARE KIT F-105K2.5 MY SAFE T PLUS UNIT INSTALLATION INSTRUCTIONS FOR MOUNTING HARDWARE KIT F-105K2.5 This kit supports installation of SAFE T PLUS : MODEL # 41-140 (RED) MODEL # 41-180 (WHITE) MODEL #41-230 (BLUE) KEEP INSTRUCTIONS

More information

MODEL 400A-60 & 400Z-72 HYDRA-LIFT KARRIERS

MODEL 400A-60 & 400Z-72 HYDRA-LIFT KARRIERS OPERATOR S MANUAL FOR 400Z SERIES MANUAL TILT S The letter Z in the model number indicates that the unit is for 55 gallon standard steel drum ( 22.5 diameter) and accepts attachments to handle a 55 gallon

More information

BEAM CLAMPS INSTRUCTION MANUAL

BEAM CLAMPS INSTRUCTION MANUAL Beam Clamp Manual 0109 10/7/2010 update BEAM CLAMPS INSTRUCTION MANUAL MODEL BC-2, -4, -6, & -8 VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586

More information

MODEL L/R/EF Sectional Tire Spreader

MODEL L/R/EF Sectional Tire Spreader MODEL L/R/EF Sectional Tire Spreader Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV08032016 P/N: 81-0195E TABLE

More information

Quadratec Dual Steering Stabilizer Kit

Quadratec Dual Steering Stabilizer Kit Quadratec Dual Steering Stabilizer Kit Installation Manual: for 97-06 (TJ) Wrangler # 16116.0202 PARTS LIST: Steering Damper - Qty 2 Black Boot & Boot Tie - Qty 2 (each) Decal - Qty 2 Hourglass Bushing

More information

Hydraulic Transmission Jacks

Hydraulic Transmission Jacks Hydraulic Transmission Jacks Operating Instructions & Parts Manual Model Number Atd-7435 Atd-7436 Atd-7437 Capacity 1100 Lb. 2000 Lb. 3000 Lb. Model Atd-7435 Model Atd-7436 Model Atd-7437 Atd Tools Inc.

More information

Heavy Duty Engine Cranes

Heavy Duty Engine Cranes Heavy Duty Engine Cranes Operating Instructions & Parts Manual Model Number ATD-7484 ATD-7485 (Foldable Legs) Capacity 2 Ton 2 Ton Model ATD-7484 Model ATD-7485 WARNING: This product may contain chemicals,

More information

Operating Instructions & Parts Manual

Operating Instructions & Parts Manual Forklift Jack Operating Instructions & Parts Manual Model Number HW93659 Capacity 4 Ton Made in the U.S.A.! This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

More information

6602LP CAPACITY: 2 TON LOW RIDER SERVICE JACK

6602LP CAPACITY: 2 TON LOW RIDER SERVICE JACK CONTENTS: Page 1 Specifications 2 Warning Information 3 Setup Instructions 4 Operating Instructions, Preventative Maintenance, Inspection and Proper Storage 5 Hydraulic Jack Maintenance Guide and Regular

More information

CART-2000 & CART-4000

CART-2000 & CART-4000 Operating nstructions & Parts Manual CART-2000 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself

More information

MODEL 7400 STRUT SPRING COMPRESSOR

MODEL 7400 STRUT SPRING COMPRESSOR MODEL 7400 STRUT SPRING COMPRESSOR Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV112712 P/N: 81-0103A TABLE OF

More information

MODEL 7600 STRUT SPRING COMPRESSOR

MODEL 7600 STRUT SPRING COMPRESSOR MODEL 7600 STRUT SPRING COMPRESSOR Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV6162014 P/N: 81-0246 TABLE OF

More information

Important. Contents. Contact us:

Important. Contents. Contact us: Operator's Manual First Edition Ninth Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall

More information

Operation & Service Manual

Operation & Service Manual Operation & Service Manual Model: 02-1248-0112 12 Ton Single Stage Jack 11/2004 Rev. 02 Includes Illustrated Parts Lists 1740 Eber Rd Tronair, Inc. Phone: (419) 866-6301 Holland, OH 43528-9794 www.tronair.com

More information

MODEL 5500 Tire Repair Station

MODEL 5500 Tire Repair Station MODEL 5500 Tire Repair Station Installation, Operation and Repair Parts Information Branick Industries, Inc. 4245 Main Ave P.O. Box 1937 Fargo, North Dakota 58103 P/N: 81-0047C TABLE OF CONTENTS SAFETY

More information

201 Series Portable Drum Rotators Operator s Manual for Morse Portable Drum Rotators

201 Series Portable Drum Rotators Operator s Manual for Morse Portable Drum Rotators Contents Page Receiving Procedures.................... 1 Warranty............................. 1 Safety Information..................... 1-2 Machine Description................... 3 Options.............................

More information

MG12K24T60V4 Mechanical Grapple

MG12K24T60V4 Mechanical Grapple 170 State Route 271 Attachment Solutions MG12K24T60V4 Mechanical Grapple Operators Manual KENCO Mechanical Grapple Operation Manual 1 TABLE OF CONTENTS 170 State Route 271 Section I. General Information....

More information

Air Operated End Lift

Air Operated End Lift Air Operated End Lift Operating Instructions & Parts Manual Model Number HW93690 Capacity 10 Ton Made in the U.S.A. This is the safety alert symbol. It is used to alert you to potential personal injury

More information

VersaHitch Bike Rack

VersaHitch Bike Rack VersaHitch Bike Rack Installation Manual: for Jeep Wrangler with VersaHitch # 92034.3000 PARTS LIST: Receiver Bases - QTY 2 Main Rack System - QTY 1 Installation Hardware - SEE PAGE 3 REQUIRED TOOLS: Safety

More information